Claus Näveke
5 years ago
committed by
GitHub
4 changed files with 168 additions and 0 deletions
@ -0,0 +1,157 @@ |
|||
/**
|
|||
* Marlin 3D Printer Firmware |
|||
* Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
|||
* |
|||
* Based on Sprinter and grbl. |
|||
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm |
|||
* |
|||
* This program is free software: you can redistribute it and/or modify |
|||
* it under the terms of the GNU General Public License as published by |
|||
* the Free Software Foundation, either version 3 of the License, or |
|||
* (at your option) any later version. |
|||
* |
|||
* This program is distributed in the hope that it will be useful, |
|||
* but WITHOUT ANY WARRANTY; without even the implied warranty of |
|||
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
|||
* GNU General Public License for more details. |
|||
* |
|||
* You should have received a copy of the GNU General Public License |
|||
* along with this program. If not, see <http://www.gnu.org/licenses/>.
|
|||
* |
|||
*/ |
|||
#pragma once |
|||
|
|||
/**
|
|||
* ANYCUBIC Trigorilla Pro (STM32F130ZET6) board pin assignments. |
|||
* It is the same used by the Tronxy X5SA thanks to ftoz1 for sharing it |
|||
* https://github.com/MarlinFirmware/Marlin/issues/14655
|
|||
* https://github.com/MarlinFirmware/Marlin/files/3401484/x5sa-main_board-2.pdf
|
|||
*/ |
|||
|
|||
#ifndef __STM32F1__ |
|||
#error "Oops! Select an STM32F1 board in 'Tools > Board.'" |
|||
#elif HOTENDS > 2 || E_STEPPERS > 2 |
|||
#error "Trigorilla Pro supports up to 2 hotends / E-steppers. Comment out this line to continue." |
|||
#endif |
|||
|
|||
#define BOARD_INFO_NAME "Trigorilla Pro" |
|||
#define DISABLE_JTAG |
|||
|
|||
//
|
|||
// EEPROM
|
|||
//
|
|||
#define FLASH_EEPROM_EMULATION |
|||
#if ENABLED(FLASH_EEPROM_EMULATION) |
|||
// SoC Flash (framework-arduinoststm32-maple/STM32F1/libraries/EEPROM/EEPROM.h)
|
|||
#define EEPROM_START_ADDRESS (0x8000000UL + (512 * 1024) - 2 * EEPROM_PAGE_SIZE) |
|||
#define EEPROM_PAGE_SIZE (0x800U) // 2KB, but will use 2x more (4KB)
|
|||
#define MARLIN_EEPROM_SIZE EEPROM_PAGE_SIZE |
|||
#else |
|||
#define MARLIN_EEPROM_SIZE (0x800U) // On SD, Limit to 2KB, require this amount of RAM
|
|||
#endif |
|||
|
|||
//
|
|||
// Limit Switches
|
|||
//
|
|||
#define X_MAX_PIN PG10 |
|||
#define Y_MAX_PIN PA12 |
|||
#define Z_MAX_PIN PA14 |
|||
#define Z_MIN_PIN PA13 |
|||
|
|||
//
|
|||
// Steppers
|
|||
//
|
|||
#define X_ENABLE_PIN PC13 |
|||
#define X_STEP_PIN PE5 |
|||
#define X_DIR_PIN PE6 |
|||
|
|||
#define Y_ENABLE_PIN PE4 |
|||
#define Y_STEP_PIN PE2 |
|||
#define Y_DIR_PIN PE3 |
|||
|
|||
#define Z_ENABLE_PIN PE1 |
|||
#define Z_STEP_PIN PB9 |
|||
#define Z_DIR_PIN PE0 |
|||
|
|||
#define E0_ENABLE_PIN PB8 |
|||
#define E0_STEP_PIN PB4 |
|||
#define E0_DIR_PIN PB5 |
|||
|
|||
#define E1_ENABLE_PIN PG8 |
|||
#define E1_STEP_PIN PC7 |
|||
#define E1_DIR_PIN PC6 |
|||
|
|||
//
|
|||
// Temperature Sensors
|
|||
//
|
|||
#define TEMP_0_PIN PA1 // TH1
|
|||
#define TEMP_BED_PIN PA0 // TB1
|
|||
|
|||
//
|
|||
// Heaters
|
|||
//
|
|||
#define HEATER_0_PIN PG12 // HEATER1
|
|||
#define HEATER_BED_PIN PG11 // HOT BED
|
|||
#define HEATER_BED_INVERTING true |
|||
|
|||
//
|
|||
// Fans
|
|||
//
|
|||
#define CONTROLLER_FAN_PIN PD6 // FAN
|
|||
#define FAN_PIN PG13 // FAN
|
|||
#define FAN1_PIN PG14 // FAN
|
|||
|
|||
//
|
|||
// Misc
|
|||
//
|
|||
#define BEEPER_PIN PB0 |
|||
#define LED_PIN PD3 |
|||
//#define POWER_LOSS_PIN PG2 // PG4 PW_DET
|
|||
#define FIL_RUNOUT_PIN PA15 // MT_DET
|
|||
|
|||
/**
|
|||
* Note: MKS Robin TFT screens use various TFT controllers |
|||
* Supported screens are based on the ILI9341, ST7789V and ILI9328 (320x240) |
|||
* ILI9488 is not supported. |
|||
* Define init sequences for other screens in u8g_dev_tft_320x240_upscale_from_128x64.cpp |
|||
* |
|||
* If the screen stays white, disable 'LCD_RESET_PIN' to let the bootloader init the screen. |
|||
* |
|||
* Setting an 'LCD_RESET_PIN' may cause a flicker when entering the LCD menu |
|||
* because Marlin uses the reset as a failsafe to revive a glitchy LCD. |
|||
*/ |
|||
#define LCD_RESET_PIN PF11 |
|||
#define LCD_BACKLIGHT_PIN PD13 |
|||
#define FSMC_CS_PIN PD7 // NE4
|
|||
#define FSMC_RS_PIN PD11 // A0
|
|||
|
|||
#define LCD_USE_DMA_FSMC // Use DMA transfers to send data to the TFT
|
|||
#define FSMC_DMA_DEV DMA2 |
|||
#define FSMC_DMA_CHANNEL DMA_CH5 |
|||
|
|||
#if ENABLED(TOUCH_BUTTONS) |
|||
#define TOUCH_CS_PIN PB7 // SPI2_NSS
|
|||
#define TOUCH_SCK_PIN PA5 // SPI2_SCK
|
|||
#define TOUCH_MISO_PIN PA6 // SPI2_MISO
|
|||
#define TOUCH_MOSI_PIN PA7 // SPI2_MOSI
|
|||
#endif |
|||
|
|||
// SPI1(PA7) & SPI3(PB5) not available
|
|||
#define ENABLE_SPI2 |
|||
|
|||
#if ENABLED(SDIO_SUPPORT) |
|||
#define SCK_PIN PB13 // SPI2 ok
|
|||
#define MISO_PIN PB14 // SPI2 ok
|
|||
#define MOSI_PIN PB15 // SPI2 ok
|
|||
#define SS_PIN PC11 // PB12 is X- ok
|
|||
#define SD_DETECT_PIN -1 // SD_CD ok
|
|||
#else |
|||
// SD as custom software SPI (SDIO pins)
|
|||
#define SCK_PIN PC12 |
|||
#define MISO_PIN PC8 |
|||
#define MOSI_PIN PD2 |
|||
#define SS_PIN -1 |
|||
#define ONBOARD_SD_CS_PIN PC11 |
|||
#define SDSS PD2 |
|||
#define SD_DETECT_PIN -1 |
|||
#endif |
Loading…
Reference in new issue