diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h
index 2d795cef95..2220f376ed 100644
--- a/Marlin/Configuration_adv.h
+++ b/Marlin/Configuration_adv.h
@@ -960,6 +960,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/Marlin/src/HAL/HAL_STM32F1/fastio.h b/Marlin/src/HAL/HAL_STM32F1/fastio.h
index 463d951c1e..3aafb9de39 100644
--- a/Marlin/src/HAL/HAL_STM32F1/fastio.h
+++ b/Marlin/src/HAL/HAL_STM32F1/fastio.h
@@ -29,32 +29,33 @@
 
 #include <libmaple/gpio.h>
 
-#define READ(IO)              (PIN_MAP[IO].gpio_device->regs->IDR & (1U << PIN_MAP[IO].gpio_bit) ? HIGH : LOW)
-#define WRITE(IO,V)           (PIN_MAP[IO].gpio_device->regs->BSRR = (1U << PIN_MAP[IO].gpio_bit) << ((V) ? 0 : 16))
-#define TOGGLE(IO)            (PIN_MAP[IO].gpio_device->regs->ODR = PIN_MAP[IO].gpio_device->regs->ODR ^ (1U << PIN_MAP[IO].gpio_bit))
+#define READ(IO)                (PIN_MAP[IO].gpio_device->regs->IDR & (1U << PIN_MAP[IO].gpio_bit) ? HIGH : LOW)
+#define WRITE(IO,V)             (PIN_MAP[IO].gpio_device->regs->BSRR = (1U << PIN_MAP[IO].gpio_bit) << ((V) ? 0 : 16))
+#define TOGGLE(IO)              (PIN_MAP[IO].gpio_device->regs->ODR = PIN_MAP[IO].gpio_device->regs->ODR ^ (1U << PIN_MAP[IO].gpio_bit))
 
-#define _GET_MODE(IO)         gpio_get_mode(PIN_MAP[IO].gpio_device, PIN_MAP[IO].gpio_bit)
-#define _SET_MODE(IO,M)       gpio_set_mode(PIN_MAP[IO].gpio_device, PIN_MAP[IO].gpio_bit, M)
-#define _SET_OUTPUT(IO)       _SET_MODE(IO, GPIO_OUTPUT_PP)
-#define _SET_OUTPUT_OD(IO)    _SET_MODE(IO, GPIO_OUTPUT_OD)
+#define _GET_MODE(IO)           gpio_get_mode(PIN_MAP[IO].gpio_device, PIN_MAP[IO].gpio_bit)
+#define _SET_MODE(IO,M)         gpio_set_mode(PIN_MAP[IO].gpio_device, PIN_MAP[IO].gpio_bit, M)
+#define _SET_OUTPUT(IO)         _SET_MODE(IO, GPIO_OUTPUT_PP)
+#define _SET_OUTPUT_OD(IO)      _SET_MODE(IO, GPIO_OUTPUT_OD)
 
-#define OUT_WRITE(IO,V)       do{ _SET_OUTPUT(IO); WRITE(IO,V); }while(0)
-#define OUT_WRITE_OD(IO,V)    do{ _SET_OUTPUT_OD(IO); WRITE(IO,V); }while(0)
+#define OUT_WRITE(IO,V)         do{ _SET_OUTPUT(IO); WRITE(IO,V); }while(0)
+#define OUT_WRITE_OD(IO,V)      do{ _SET_OUTPUT_OD(IO); WRITE(IO,V); }while(0)
 
-#define SET_INPUT(IO)         _SET_MODE(IO, GPIO_INPUT_FLOATING)
-#define SET_INPUT_PULLUP(IO)  _SET_MODE(IO, GPIO_INPUT_PU)
-#define SET_OUTPUT(IO)        OUT_WRITE(IO, LOW)
-#define SET_PWM(IO)           pinMode(IO, PWM)    // do{ gpio_set_mode(PIN_MAP[pin].gpio_device, PIN_MAP[pin].gpio_bit, GPIO_AF_OUTPUT_PP); timer_set_mode(PIN_MAP[pin].timer_device, PIN_MAP[pin].timer_channel, TIMER_PWM); }while(0)
-#define SET_PWM_OD(IO)        pinMode(IO, PWM_OPEN_DRAIN)
+#define SET_INPUT(IO)           _SET_MODE(IO, GPIO_INPUT_FLOATING)
+#define SET_INPUT_PULLUP(IO)    _SET_MODE(IO, GPIO_INPUT_PU)
+#define SET_INPUT_PULLDOWN(IO)  _SET_MODE(IO, GPIO_INPUT_PD)
+#define SET_OUTPUT(IO)          OUT_WRITE(IO, LOW)
+#define SET_PWM(IO)             pinMode(IO, PWM)    // do{ gpio_set_mode(PIN_MAP[pin].gpio_device, PIN_MAP[pin].gpio_bit, GPIO_AF_OUTPUT_PP); timer_set_mode(PIN_MAP[pin].timer_device, PIN_MAP[pin].timer_channel, TIMER_PWM); }while(0)
+#define SET_PWM_OD(IO)          pinMode(IO, PWM_OPEN_DRAIN)
 
-#define IS_INPUT(IO)          (_GET_MODE(IO) == GPIO_INPUT_FLOATING || _GET_MODE(IO) == GPIO_INPUT_ANALOG || _GET_MODE(IO) == GPIO_INPUT_PU || _GET_MODE(IO) == GPIO_INPUT_PD)
-#define IS_OUTPUT(IO)         (_GET_MODE(IO) == GPIO_OUTPUT_PP || _GET_MODE(IO) == GPIO_OUTPUT_OD)
+#define IS_INPUT(IO)            (_GET_MODE(IO) == GPIO_INPUT_FLOATING || _GET_MODE(IO) == GPIO_INPUT_ANALOG || _GET_MODE(IO) == GPIO_INPUT_PU || _GET_MODE(IO) == GPIO_INPUT_PD)
+#define IS_OUTPUT(IO)           (_GET_MODE(IO) == GPIO_OUTPUT_PP || _GET_MODE(IO) == GPIO_OUTPUT_OD)
 
-#define PWM_PIN(IO)           (PIN_MAP[IO].timer_device != nullptr)
+#define PWM_PIN(IO)             (PIN_MAP[IO].timer_device != nullptr)
 
 // digitalRead/Write wrappers
-#define extDigitalRead(IO)    digitalRead(IO)
-#define extDigitalWrite(IO,V) digitalWrite(IO,V)
+#define extDigitalRead(IO)      digitalRead(IO)
+#define extDigitalWrite(IO,V)   digitalWrite(IO,V)
 
 //
 // Pins Definitions
diff --git a/Marlin/src/feature/power_loss_recovery.cpp b/Marlin/src/feature/power_loss_recovery.cpp
index 52671b0ecb..0cf0fc5885 100644
--- a/Marlin/src/feature/power_loss_recovery.cpp
+++ b/Marlin/src/feature/power_loss_recovery.cpp
@@ -65,6 +65,9 @@ PrintJobRecovery recovery;
 #ifndef POWER_LOSS_RETRACT_LEN
   #define POWER_LOSS_RETRACT_LEN 0
 #endif
+#ifndef POWER_LOSS_ZRAISE
+  #define POWER_LOSS_ZRAISE 2
+#endif
 
 /**
  * Clear the recovery info
@@ -235,10 +238,34 @@ void PrintJobRecovery::save(const bool force/*=false*/, const bool save_queue/*=
 }
 
 #if PIN_EXISTS(POWER_LOSS)
+
   void PrintJobRecovery::_outage() {
-    save(true);
+    #if ENABLED(BACKUP_POWER_SUPPLY)
+      static bool lock = false;
+      if (lock) return; // No re-entrance from idle() during raise_z()
+      lock = true;
+    #endif
+    if (IS_SD_PRINTING()) save(true);
+    #if ENABLED(BACKUP_POWER_SUPPLY)
+      raise_z();
+    #endif
+
     kill(GET_TEXT(MSG_OUTAGE_RECOVERY));
   }
+
+  #if ENABLED(BACKUP_POWER_SUPPLY)
+
+    void PrintJobRecovery::raise_z() {
+      // Disable all heaters to reduce power loss
+      thermalManager.disable_all_heaters();
+      quickstop_stepper();
+      // Raise Z axis
+      gcode.process_subcommands_now_P(PSTR("G91\nG0 Z" STRINGIFY(POWER_LOSS_ZRAISE)));
+      planner.synchronize();
+    }
+
+  #endif
+
 #endif
 
 /**
@@ -260,8 +287,6 @@ void PrintJobRecovery::write() {
  */
 void PrintJobRecovery::resume() {
 
-  #define RECOVERY_ZRAISE 2
-
   const uint32_t resume_sdpos = info.sdpos; // Get here before the stepper ISR overwrites it
 
   #if HAS_LEVELING
@@ -272,15 +297,27 @@ void PrintJobRecovery::resume() {
   // Reset E, raise Z, home XY...
   gcode.process_subcommands_now_P(PSTR("G92.9 E0"
     #if Z_HOME_DIR > 0
-      // If Z homing goes to max, reset E and home all
-      "\nG28R0"
+
+      // If Z homing goes to max, just reset E and home all
+      "\n"
+      "G28R0"
       #if ENABLED(MARLIN_DEV_MODE)
         "S"
       #endif
-    #else
+
+    #else // "G92.9 E0 ..."
+
       // Set Z to 0, raise Z by RECOVERY_ZRAISE, and Home (XY only for Cartesian)
       // with no raise. (Only do simulated homing in Marlin Dev Mode.)
-      "Z0\nG1Z" STRINGIFY(RECOVERY_ZRAISE) "\nG28R0"
+      #if ENABLED(BACKUP_POWER_SUPPLY)
+        "Z" STRINGIFY(POWER_LOSS_ZRAISE)    // Z-axis was already raised at outage
+      #else
+        "Z0\n"                              // Set Z=0
+        "G1Z" STRINGIFY(POWER_LOSS_ZRAISE)  // Raise Z
+      #endif
+      "\n"
+
+      "G28R0"
       #if ENABLED(MARLIN_DEV_MODE)
         "S"
       #elif !IS_KINEMATIC
diff --git a/Marlin/src/feature/power_loss_recovery.h b/Marlin/src/feature/power_loss_recovery.h
index 92d7f7cdb3..771fce44df 100644
--- a/Marlin/src/feature/power_loss_recovery.h
+++ b/Marlin/src/feature/power_loss_recovery.h
@@ -168,7 +168,7 @@ class PrintJobRecovery {
 
   #if PIN_EXISTS(POWER_LOSS)
     static inline void outage() {
-      if (enabled && IS_SD_PRINTING() && READ(POWER_LOSS_PIN) == POWER_LOSS_STATE)
+      if (enabled && READ(POWER_LOSS_PIN) == POWER_LOSS_STATE)
         _outage();
     }
   #endif
@@ -184,6 +184,10 @@ class PrintJobRecovery {
   private:
     static void write();
 
+  #if ENABLED(BACKUP_POWER_SUPPLY)
+    static void raise_z();
+  #endif
+
   #if PIN_EXISTS(POWER_LOSS)
     static void _outage();
   #endif
diff --git a/Marlin/src/gcode/feature/powerloss/M1000.cpp b/Marlin/src/gcode/feature/powerloss/M1000.cpp
index c454a34c05..f14dc60685 100644
--- a/Marlin/src/gcode/feature/powerloss/M1000.cpp
+++ b/Marlin/src/gcode/feature/powerloss/M1000.cpp
@@ -52,8 +52,13 @@ inline void plr_error(PGM_P const prefix) {
 void GcodeSuite::M1000() {
 
   if (recovery.valid()) {
-    if (parser.seen('S'))
-      ui.goto_screen(menu_job_recovery);
+    if (parser.seen('S')) {
+      #if HAS_LCD_MENU
+        ui.goto_screen(menu_job_recovery);
+      #else
+        SERIAL_ECHO_MSG("Resume requires LCD.");
+      #endif
+    }
     else
       recovery.resume();
   }
diff --git a/Marlin/src/inc/SanityCheck.h b/Marlin/src/inc/SanityCheck.h
index e356c6f9b7..4f53dd1332 100644
--- a/Marlin/src/inc/SanityCheck.h
+++ b/Marlin/src/inc/SanityCheck.h
@@ -2336,8 +2336,8 @@ static_assert(   _ARR_TEST(3,0) && _ARR_TEST(3,1) && _ARR_TEST(3,2)
   #endif
 #endif
 
-#if ENABLED(POWER_LOSS_RECOVERY) && DISABLED(ULTIPANEL)
-  #error "POWER_LOSS_RECOVERY currently requires an LCD Controller."
+#if ENABLED(BACKUP_POWER_SUPPLY) && !PIN_EXISTS(POWER_LOSS)
+  #error "BACKUP_POWER_SUPPLY requires a POWER_LOSS_PIN."
 #endif
 
 #if ENABLED(Z_STEPPER_AUTO_ALIGN)
diff --git a/config/default/Configuration_adv.h b/config/default/Configuration_adv.h
index 2d795cef95..2220f376ed 100644
--- a/config/default/Configuration_adv.h
+++ b/config/default/Configuration_adv.h
@@ -960,6 +960,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/3DFabXYZ/Migbot/Configuration_adv.h b/config/examples/3DFabXYZ/Migbot/Configuration_adv.h
index 0531f0495a..c76afc181c 100644
--- a/config/examples/3DFabXYZ/Migbot/Configuration_adv.h
+++ b/config/examples/3DFabXYZ/Migbot/Configuration_adv.h
@@ -960,6 +960,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/ADIMLab/Gantry v1/Configuration_adv.h b/config/examples/ADIMLab/Gantry v1/Configuration_adv.h
index f195c6b342..3d3bbffafb 100644
--- a/config/examples/ADIMLab/Gantry v1/Configuration_adv.h	
+++ b/config/examples/ADIMLab/Gantry v1/Configuration_adv.h	
@@ -960,6 +960,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         28 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/ADIMLab/Gantry v2/Configuration_adv.h b/config/examples/ADIMLab/Gantry v2/Configuration_adv.h
index f6efba14b4..5971cdbf22 100644
--- a/config/examples/ADIMLab/Gantry v2/Configuration_adv.h	
+++ b/config/examples/ADIMLab/Gantry v2/Configuration_adv.h	
@@ -960,6 +960,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/AlephObjects/TAZ4/Configuration_adv.h b/config/examples/AlephObjects/TAZ4/Configuration_adv.h
index abcc783b80..b21db2f3df 100644
--- a/config/examples/AlephObjects/TAZ4/Configuration_adv.h
+++ b/config/examples/AlephObjects/TAZ4/Configuration_adv.h
@@ -960,6 +960,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/Alfawise/U20-bltouch/Configuration_adv.h b/config/examples/Alfawise/U20-bltouch/Configuration_adv.h
index 386fbd0632..b5d0f7cb78 100644
--- a/config/examples/Alfawise/U20-bltouch/Configuration_adv.h
+++ b/config/examples/Alfawise/U20-bltouch/Configuration_adv.h
@@ -961,6 +961,8 @@
    */
   #define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/Alfawise/U20/Configuration_adv.h b/config/examples/Alfawise/U20/Configuration_adv.h
index 0769d251f1..da18ae8971 100644
--- a/config/examples/Alfawise/U20/Configuration_adv.h
+++ b/config/examples/Alfawise/U20/Configuration_adv.h
@@ -960,6 +960,8 @@
    */
   #define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/AliExpress/UM2pExt/Configuration_adv.h b/config/examples/AliExpress/UM2pExt/Configuration_adv.h
index 1a7816181a..c9ab0d2451 100644
--- a/config/examples/AliExpress/UM2pExt/Configuration_adv.h
+++ b/config/examples/AliExpress/UM2pExt/Configuration_adv.h
@@ -960,6 +960,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/Anet/A2/Configuration_adv.h b/config/examples/Anet/A2/Configuration_adv.h
index 9a32e13000..4281d075cd 100644
--- a/config/examples/Anet/A2/Configuration_adv.h
+++ b/config/examples/Anet/A2/Configuration_adv.h
@@ -960,6 +960,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/Anet/A2plus/Configuration_adv.h b/config/examples/Anet/A2plus/Configuration_adv.h
index 9a32e13000..4281d075cd 100644
--- a/config/examples/Anet/A2plus/Configuration_adv.h
+++ b/config/examples/Anet/A2plus/Configuration_adv.h
@@ -960,6 +960,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/Anet/A6/Configuration_adv.h b/config/examples/Anet/A6/Configuration_adv.h
index b587fcfc00..cc3a59b3fd 100644
--- a/config/examples/Anet/A6/Configuration_adv.h
+++ b/config/examples/Anet/A6/Configuration_adv.h
@@ -960,6 +960,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/Anet/A8/Configuration_adv.h b/config/examples/Anet/A8/Configuration_adv.h
index d46c59accf..dae7767ef3 100644
--- a/config/examples/Anet/A8/Configuration_adv.h
+++ b/config/examples/Anet/A8/Configuration_adv.h
@@ -960,6 +960,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/Anet/A8plus/Configuration_adv.h b/config/examples/Anet/A8plus/Configuration_adv.h
index 10cac4fad5..8dd831ba98 100644
--- a/config/examples/Anet/A8plus/Configuration_adv.h
+++ b/config/examples/Anet/A8plus/Configuration_adv.h
@@ -960,6 +960,8 @@
    */
   #define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/Anet/E16/Configuration_adv.h b/config/examples/Anet/E16/Configuration_adv.h
index 772cf31c3e..16da6fdbad 100644
--- a/config/examples/Anet/E16/Configuration_adv.h
+++ b/config/examples/Anet/E16/Configuration_adv.h
@@ -960,6 +960,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/AnyCubic/i3/Configuration_adv.h b/config/examples/AnyCubic/i3/Configuration_adv.h
index 7c9e6c3dd9..192260a204 100644
--- a/config/examples/AnyCubic/i3/Configuration_adv.h
+++ b/config/examples/AnyCubic/i3/Configuration_adv.h
@@ -960,6 +960,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/ArmEd/Configuration_adv.h b/config/examples/ArmEd/Configuration_adv.h
index 51f6125b9c..a46cd535e7 100644
--- a/config/examples/ArmEd/Configuration_adv.h
+++ b/config/examples/ArmEd/Configuration_adv.h
@@ -964,6 +964,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h b/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h
index 6c0a284ea3..f9d5b3e26b 100644
--- a/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h
+++ b/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h
@@ -960,6 +960,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/BIBO/TouchX/default/Configuration_adv.h b/config/examples/BIBO/TouchX/default/Configuration_adv.h
index 6bf31f8f94..56423a519f 100644
--- a/config/examples/BIBO/TouchX/default/Configuration_adv.h
+++ b/config/examples/BIBO/TouchX/default/Configuration_adv.h
@@ -960,6 +960,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/BQ/Hephestos/Configuration_adv.h b/config/examples/BQ/Hephestos/Configuration_adv.h
index 2b5e8a582a..adf1b45e1e 100644
--- a/config/examples/BQ/Hephestos/Configuration_adv.h
+++ b/config/examples/BQ/Hephestos/Configuration_adv.h
@@ -960,6 +960,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/BQ/Hephestos_2/Configuration_adv.h b/config/examples/BQ/Hephestos_2/Configuration_adv.h
index 29b4bed784..f229ffa39e 100644
--- a/config/examples/BQ/Hephestos_2/Configuration_adv.h
+++ b/config/examples/BQ/Hephestos_2/Configuration_adv.h
@@ -968,6 +968,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/BQ/WITBOX/Configuration_adv.h b/config/examples/BQ/WITBOX/Configuration_adv.h
index 2b5e8a582a..adf1b45e1e 100644
--- a/config/examples/BQ/WITBOX/Configuration_adv.h
+++ b/config/examples/BQ/WITBOX/Configuration_adv.h
@@ -960,6 +960,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/Cartesio/Configuration_adv.h b/config/examples/Cartesio/Configuration_adv.h
index 38b1f3d050..f6ac22b509 100644
--- a/config/examples/Cartesio/Configuration_adv.h
+++ b/config/examples/Cartesio/Configuration_adv.h
@@ -960,6 +960,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/Creality/CR-10/Configuration_adv.h b/config/examples/Creality/CR-10/Configuration_adv.h
index c93ab47381..1a0467811c 100644
--- a/config/examples/Creality/CR-10/Configuration_adv.h
+++ b/config/examples/Creality/CR-10/Configuration_adv.h
@@ -960,6 +960,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/Creality/CR-10S/Configuration_adv.h b/config/examples/Creality/CR-10S/Configuration_adv.h
index 63c4a41d9e..86136029ab 100644
--- a/config/examples/Creality/CR-10S/Configuration_adv.h
+++ b/config/examples/Creality/CR-10S/Configuration_adv.h
@@ -960,6 +960,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/Creality/CR-10_5S/Configuration_adv.h b/config/examples/Creality/CR-10_5S/Configuration_adv.h
index 0c63c4afdc..d8b0cb40c8 100644
--- a/config/examples/Creality/CR-10_5S/Configuration_adv.h
+++ b/config/examples/Creality/CR-10_5S/Configuration_adv.h
@@ -960,6 +960,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/Creality/CR-10mini/Configuration_adv.h b/config/examples/Creality/CR-10mini/Configuration_adv.h
index b620382e94..91f3ff00fa 100644
--- a/config/examples/Creality/CR-10mini/Configuration_adv.h
+++ b/config/examples/Creality/CR-10mini/Configuration_adv.h
@@ -960,6 +960,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/Creality/CR-20 Pro/Configuration_adv.h b/config/examples/Creality/CR-20 Pro/Configuration_adv.h
index 941187956f..4cb510f4b8 100644
--- a/config/examples/Creality/CR-20 Pro/Configuration_adv.h	
+++ b/config/examples/Creality/CR-20 Pro/Configuration_adv.h	
@@ -960,6 +960,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/Creality/CR-20/Configuration_adv.h b/config/examples/Creality/CR-20/Configuration_adv.h
index fafc8f292f..3fa373c31a 100644
--- a/config/examples/Creality/CR-20/Configuration_adv.h
+++ b/config/examples/Creality/CR-20/Configuration_adv.h
@@ -960,6 +960,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/Creality/CR-8/Configuration_adv.h b/config/examples/Creality/CR-8/Configuration_adv.h
index 4519a6c629..b5994c0f05 100644
--- a/config/examples/Creality/CR-8/Configuration_adv.h
+++ b/config/examples/Creality/CR-8/Configuration_adv.h
@@ -960,6 +960,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/Creality/Ender-2/Configuration_adv.h b/config/examples/Creality/Ender-2/Configuration_adv.h
index 4cc20f1499..36bc83327d 100644
--- a/config/examples/Creality/Ender-2/Configuration_adv.h
+++ b/config/examples/Creality/Ender-2/Configuration_adv.h
@@ -960,6 +960,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/Creality/Ender-3/Configuration_adv.h b/config/examples/Creality/Ender-3/Configuration_adv.h
index 17162201f9..22aae3047b 100644
--- a/config/examples/Creality/Ender-3/Configuration_adv.h
+++ b/config/examples/Creality/Ender-3/Configuration_adv.h
@@ -960,6 +960,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/Creality/Ender-4/Configuration_adv.h b/config/examples/Creality/Ender-4/Configuration_adv.h
index b015a22316..913b4c655f 100644
--- a/config/examples/Creality/Ender-4/Configuration_adv.h
+++ b/config/examples/Creality/Ender-4/Configuration_adv.h
@@ -960,6 +960,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/Creality/Ender-5/Configuration_adv.h b/config/examples/Creality/Ender-5/Configuration_adv.h
index dd86e87e58..bbe8f6fb4a 100644
--- a/config/examples/Creality/Ender-5/Configuration_adv.h
+++ b/config/examples/Creality/Ender-5/Configuration_adv.h
@@ -960,6 +960,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h b/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h
index c9cb50349e..299e404181 100644
--- a/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h	
+++ b/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h	
@@ -960,6 +960,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/EVNOVO (Artillery)/Sidewinder X1/Configuration_adv.h b/config/examples/EVNOVO (Artillery)/Sidewinder X1/Configuration_adv.h
index dc9bc367b3..8e61229309 100755
--- a/config/examples/EVNOVO (Artillery)/Sidewinder X1/Configuration_adv.h	
+++ b/config/examples/EVNOVO (Artillery)/Sidewinder X1/Configuration_adv.h	
@@ -960,6 +960,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/Einstart-S/Configuration_adv.h b/config/examples/Einstart-S/Configuration_adv.h
index c3e7568daa..0ea924ee65 100644
--- a/config/examples/Einstart-S/Configuration_adv.h
+++ b/config/examples/Einstart-S/Configuration_adv.h
@@ -960,6 +960,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/FYSETC/AIO_II/Configuration_adv.h b/config/examples/FYSETC/AIO_II/Configuration_adv.h
index c64833db44..d34b606bf1 100644
--- a/config/examples/FYSETC/AIO_II/Configuration_adv.h
+++ b/config/examples/FYSETC/AIO_II/Configuration_adv.h
@@ -960,6 +960,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration_adv.h b/config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration_adv.h
index affc7a56a1..9f12f8dfc0 100644
--- a/config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration_adv.h	
+++ b/config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration_adv.h	
@@ -960,6 +960,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/FYSETC/Cheetah 1.2/base/Configuration_adv.h b/config/examples/FYSETC/Cheetah 1.2/base/Configuration_adv.h
index affc7a56a1..9f12f8dfc0 100644
--- a/config/examples/FYSETC/Cheetah 1.2/base/Configuration_adv.h	
+++ b/config/examples/FYSETC/Cheetah 1.2/base/Configuration_adv.h	
@@ -960,6 +960,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/FYSETC/Cheetah/BLTouch/Configuration_adv.h b/config/examples/FYSETC/Cheetah/BLTouch/Configuration_adv.h
index affc7a56a1..9f12f8dfc0 100644
--- a/config/examples/FYSETC/Cheetah/BLTouch/Configuration_adv.h
+++ b/config/examples/FYSETC/Cheetah/BLTouch/Configuration_adv.h
@@ -960,6 +960,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/FYSETC/Cheetah/base/Configuration_adv.h b/config/examples/FYSETC/Cheetah/base/Configuration_adv.h
index affc7a56a1..9f12f8dfc0 100644
--- a/config/examples/FYSETC/Cheetah/base/Configuration_adv.h
+++ b/config/examples/FYSETC/Cheetah/base/Configuration_adv.h
@@ -960,6 +960,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/FYSETC/F6_13/Configuration_adv.h b/config/examples/FYSETC/F6_13/Configuration_adv.h
index e6ae67a590..9cfb57c300 100644
--- a/config/examples/FYSETC/F6_13/Configuration_adv.h
+++ b/config/examples/FYSETC/F6_13/Configuration_adv.h
@@ -960,6 +960,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/Felix/DUAL/Configuration_adv.h b/config/examples/Felix/DUAL/Configuration_adv.h
index f7f441d4f2..160b43653f 100644
--- a/config/examples/Felix/DUAL/Configuration_adv.h
+++ b/config/examples/Felix/DUAL/Configuration_adv.h
@@ -960,6 +960,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/Felix/Single/Configuration_adv.h b/config/examples/Felix/Single/Configuration_adv.h
index f7f441d4f2..160b43653f 100644
--- a/config/examples/Felix/Single/Configuration_adv.h
+++ b/config/examples/Felix/Single/Configuration_adv.h
@@ -960,6 +960,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/FlashForge/CreatorPro/Configuration_adv.h b/config/examples/FlashForge/CreatorPro/Configuration_adv.h
index 2e32f62008..7c9783ef43 100644
--- a/config/examples/FlashForge/CreatorPro/Configuration_adv.h
+++ b/config/examples/FlashForge/CreatorPro/Configuration_adv.h
@@ -959,6 +959,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/FolgerTech/i3-2020/Configuration_adv.h b/config/examples/FolgerTech/i3-2020/Configuration_adv.h
index 8206074d79..2a59f13568 100644
--- a/config/examples/FolgerTech/i3-2020/Configuration_adv.h
+++ b/config/examples/FolgerTech/i3-2020/Configuration_adv.h
@@ -960,6 +960,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/Formbot/Raptor/Configuration_adv.h b/config/examples/Formbot/Raptor/Configuration_adv.h
index f04d3b7c4e..7aa6dc10a1 100644
--- a/config/examples/Formbot/Raptor/Configuration_adv.h
+++ b/config/examples/Formbot/Raptor/Configuration_adv.h
@@ -960,6 +960,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/Formbot/T_Rex_2+/Configuration_adv.h b/config/examples/Formbot/T_Rex_2+/Configuration_adv.h
index 466bcca85f..9bae1d51e2 100644
--- a/config/examples/Formbot/T_Rex_2+/Configuration_adv.h
+++ b/config/examples/Formbot/T_Rex_2+/Configuration_adv.h
@@ -952,6 +952,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/Formbot/T_Rex_3/Configuration_adv.h b/config/examples/Formbot/T_Rex_3/Configuration_adv.h
index 788687f033..e016e7e981 100644
--- a/config/examples/Formbot/T_Rex_3/Configuration_adv.h
+++ b/config/examples/Formbot/T_Rex_3/Configuration_adv.h
@@ -964,6 +964,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/Geeetech/A10/Configuration_adv.h b/config/examples/Geeetech/A10/Configuration_adv.h
index a03bcafd91..3a9464b6d6 100644
--- a/config/examples/Geeetech/A10/Configuration_adv.h
+++ b/config/examples/Geeetech/A10/Configuration_adv.h
@@ -960,6 +960,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/Geeetech/A10M/Configuration_adv.h b/config/examples/Geeetech/A10M/Configuration_adv.h
index 5c2753c6fc..a00e5cde49 100644
--- a/config/examples/Geeetech/A10M/Configuration_adv.h
+++ b/config/examples/Geeetech/A10M/Configuration_adv.h
@@ -960,6 +960,8 @@
    */
   #define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     #define POWER_LOSS_PIN           69 // Pin to detect power loss
     #define POWER_LOSS_STATE        LOW // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/Geeetech/A20M/Configuration_adv.h b/config/examples/Geeetech/A20M/Configuration_adv.h
index a4bbf1ab2e..2a2c6438a2 100644
--- a/config/examples/Geeetech/A20M/Configuration_adv.h
+++ b/config/examples/Geeetech/A20M/Configuration_adv.h
@@ -960,6 +960,8 @@
    */
   #define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     #define POWER_LOSS_PIN           69 // Pin to detect power loss
     #define POWER_LOSS_STATE        LOW // State of pin indicating power loss
     #define POWER_LOSS_PULL             // Set pullup / pulldown as appropriate
diff --git a/config/examples/Geeetech/MeCreator2/Configuration_adv.h b/config/examples/Geeetech/MeCreator2/Configuration_adv.h
index 2dc7184e6f..a5b6c76cf7 100644
--- a/config/examples/Geeetech/MeCreator2/Configuration_adv.h
+++ b/config/examples/Geeetech/MeCreator2/Configuration_adv.h
@@ -960,6 +960,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h b/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h
index a03bcafd91..3a9464b6d6 100644
--- a/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h	
+++ b/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h	
@@ -960,6 +960,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h b/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h
index a03bcafd91..3a9464b6d6 100644
--- a/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h	
+++ b/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h	
@@ -960,6 +960,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/HMS434/Configuration_adv.h b/config/examples/HMS434/Configuration_adv.h
index 765325b5a2..6d50f426bf 100644
--- a/config/examples/HMS434/Configuration_adv.h
+++ b/config/examples/HMS434/Configuration_adv.h
@@ -945,6 +945,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PURGE_LEN   20 // (mm) Length of filament to purge on resume
diff --git a/config/examples/Infitary/i3-M508/Configuration_adv.h b/config/examples/Infitary/i3-M508/Configuration_adv.h
index cb448044ad..a721f46e81 100644
--- a/config/examples/Infitary/i3-M508/Configuration_adv.h
+++ b/config/examples/Infitary/i3-M508/Configuration_adv.h
@@ -960,6 +960,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/JGAurora/A1/Configuration_adv.h b/config/examples/JGAurora/A1/Configuration_adv.h
index ff76107f32..4eec43f38b 100644
--- a/config/examples/JGAurora/A1/Configuration_adv.h
+++ b/config/examples/JGAurora/A1/Configuration_adv.h
@@ -965,6 +965,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/JGAurora/A5/Configuration_adv.h b/config/examples/JGAurora/A5/Configuration_adv.h
index 28e62d2122..d1ab25f23a 100644
--- a/config/examples/JGAurora/A5/Configuration_adv.h
+++ b/config/examples/JGAurora/A5/Configuration_adv.h
@@ -960,6 +960,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/JGAurora/A5S/Configuration_adv.h b/config/examples/JGAurora/A5S/Configuration_adv.h
index ff76107f32..4eec43f38b 100644
--- a/config/examples/JGAurora/A5S/Configuration_adv.h
+++ b/config/examples/JGAurora/A5S/Configuration_adv.h
@@ -965,6 +965,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/MakerParts/Configuration_adv.h b/config/examples/MakerParts/Configuration_adv.h
index 5cf277eab2..a0c4259341 100644
--- a/config/examples/MakerParts/Configuration_adv.h
+++ b/config/examples/MakerParts/Configuration_adv.h
@@ -957,6 +957,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/Malyan/M150/Configuration_adv.h b/config/examples/Malyan/M150/Configuration_adv.h
index 454369fb9b..6cc2eadfae 100644
--- a/config/examples/Malyan/M150/Configuration_adv.h
+++ b/config/examples/Malyan/M150/Configuration_adv.h
@@ -957,6 +957,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/Malyan/M200/Configuration_adv.h b/config/examples/Malyan/M200/Configuration_adv.h
index 02d3a00a5f..a84ffab9b7 100644
--- a/config/examples/Malyan/M200/Configuration_adv.h
+++ b/config/examples/Malyan/M200/Configuration_adv.h
@@ -959,6 +959,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/Micromake/C1/enhanced/Configuration_adv.h b/config/examples/Micromake/C1/enhanced/Configuration_adv.h
index 0d082c3af7..c8209f8d86 100644
--- a/config/examples/Micromake/C1/enhanced/Configuration_adv.h
+++ b/config/examples/Micromake/C1/enhanced/Configuration_adv.h
@@ -957,6 +957,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/Mks/Robin/Configuration_adv.h b/config/examples/Mks/Robin/Configuration_adv.h
index 020deb50cc..5d3152e633 100644
--- a/config/examples/Mks/Robin/Configuration_adv.h
+++ b/config/examples/Mks/Robin/Configuration_adv.h
@@ -957,6 +957,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/Mks/Sbase/Configuration_adv.h b/config/examples/Mks/Sbase/Configuration_adv.h
index 1c895f58f6..616511ebcc 100644
--- a/config/examples/Mks/Sbase/Configuration_adv.h
+++ b/config/examples/Mks/Sbase/Configuration_adv.h
@@ -958,6 +958,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/RapideLite/RL200/Configuration_adv.h b/config/examples/RapideLite/RL200/Configuration_adv.h
index 6e1d2315c5..322fc87231 100644
--- a/config/examples/RapideLite/RL200/Configuration_adv.h
+++ b/config/examples/RapideLite/RL200/Configuration_adv.h
@@ -957,6 +957,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/RigidBot/Configuration_adv.h b/config/examples/RigidBot/Configuration_adv.h
index 8ea5acecbd..40d88dd6a5 100644
--- a/config/examples/RigidBot/Configuration_adv.h
+++ b/config/examples/RigidBot/Configuration_adv.h
@@ -957,6 +957,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/SCARA/Configuration_adv.h b/config/examples/SCARA/Configuration_adv.h
index 68a86e0e65..c947fbf1b6 100644
--- a/config/examples/SCARA/Configuration_adv.h
+++ b/config/examples/SCARA/Configuration_adv.h
@@ -957,6 +957,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h b/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h
index 7216d55212..f88043c886 100644
--- a/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h
+++ b/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h
@@ -957,6 +957,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/Sanguinololu/Configuration_adv.h b/config/examples/Sanguinololu/Configuration_adv.h
index 8b79f756e2..b85ebeff4e 100644
--- a/config/examples/Sanguinololu/Configuration_adv.h
+++ b/config/examples/Sanguinololu/Configuration_adv.h
@@ -957,6 +957,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/Tevo/Michelangelo/Configuration_adv.h b/config/examples/Tevo/Michelangelo/Configuration_adv.h
index 85ee27fbaf..88ca1c074d 100644
--- a/config/examples/Tevo/Michelangelo/Configuration_adv.h
+++ b/config/examples/Tevo/Michelangelo/Configuration_adv.h
@@ -957,6 +957,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/Tevo/Tarantula Pro/Configuration_adv.h b/config/examples/Tevo/Tarantula Pro/Configuration_adv.h
index 314d46966a..26f5d8a06b 100755
--- a/config/examples/Tevo/Tarantula Pro/Configuration_adv.h	
+++ b/config/examples/Tevo/Tarantula Pro/Configuration_adv.h	
@@ -957,6 +957,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration_adv.h b/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration_adv.h
index 5981cb0112..c8a85545fc 100755
--- a/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration_adv.h	
+++ b/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration_adv.h	
@@ -957,6 +957,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration_adv.h b/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration_adv.h
index 5981cb0112..c8a85545fc 100755
--- a/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration_adv.h	
+++ b/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration_adv.h	
@@ -957,6 +957,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/TheBorg/Configuration_adv.h b/config/examples/TheBorg/Configuration_adv.h
index 0d2ca00636..8ac80ffefe 100644
--- a/config/examples/TheBorg/Configuration_adv.h
+++ b/config/examples/TheBorg/Configuration_adv.h
@@ -957,6 +957,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/TinyBoy2/Configuration_adv.h b/config/examples/TinyBoy2/Configuration_adv.h
index 18b796ae89..69835e01cc 100644
--- a/config/examples/TinyBoy2/Configuration_adv.h
+++ b/config/examples/TinyBoy2/Configuration_adv.h
@@ -957,6 +957,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/Tronxy/X3A/Configuration_adv.h b/config/examples/Tronxy/X3A/Configuration_adv.h
index 7cba362a8f..55a99620f0 100644
--- a/config/examples/Tronxy/X3A/Configuration_adv.h
+++ b/config/examples/Tronxy/X3A/Configuration_adv.h
@@ -957,6 +957,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/Tronxy/X5S-2E/Configuration_adv.h b/config/examples/Tronxy/X5S-2E/Configuration_adv.h
index caacac95d4..d23a8696dc 100644
--- a/config/examples/Tronxy/X5S-2E/Configuration_adv.h
+++ b/config/examples/Tronxy/X5S-2E/Configuration_adv.h
@@ -957,6 +957,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/UltiMachine/Archim1/Configuration_adv.h b/config/examples/UltiMachine/Archim1/Configuration_adv.h
index bb4df0d36d..17357f5b57 100644
--- a/config/examples/UltiMachine/Archim1/Configuration_adv.h
+++ b/config/examples/UltiMachine/Archim1/Configuration_adv.h
@@ -957,6 +957,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/UltiMachine/Archim2/Configuration_adv.h b/config/examples/UltiMachine/Archim2/Configuration_adv.h
index a3d7618971..1949aa6374 100644
--- a/config/examples/UltiMachine/Archim2/Configuration_adv.h
+++ b/config/examples/UltiMachine/Archim2/Configuration_adv.h
@@ -957,6 +957,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/VORONDesign/Configuration_adv.h b/config/examples/VORONDesign/Configuration_adv.h
index 9bfb8672a6..9b6fff1722 100644
--- a/config/examples/VORONDesign/Configuration_adv.h
+++ b/config/examples/VORONDesign/Configuration_adv.h
@@ -957,6 +957,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/Velleman/K8200/Configuration_adv.h b/config/examples/Velleman/K8200/Configuration_adv.h
index 2ff3603389..fd2f8a5219 100644
--- a/config/examples/Velleman/K8200/Configuration_adv.h
+++ b/config/examples/Velleman/K8200/Configuration_adv.h
@@ -970,6 +970,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/Velleman/K8400/Dual-head/Configuration_adv.h b/config/examples/Velleman/K8400/Dual-head/Configuration_adv.h
index b72cfcf310..9d2a94a28d 100644
--- a/config/examples/Velleman/K8400/Dual-head/Configuration_adv.h
+++ b/config/examples/Velleman/K8400/Dual-head/Configuration_adv.h
@@ -957,6 +957,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/Velleman/K8400/Single-head/Configuration_adv.h b/config/examples/Velleman/K8400/Single-head/Configuration_adv.h
index b72cfcf310..9d2a94a28d 100644
--- a/config/examples/Velleman/K8400/Single-head/Configuration_adv.h
+++ b/config/examples/Velleman/K8400/Single-head/Configuration_adv.h
@@ -957,6 +957,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/WASP/PowerWASP/Configuration_adv.h b/config/examples/WASP/PowerWASP/Configuration_adv.h
index cfe6fd16aa..f199cfa283 100644
--- a/config/examples/WASP/PowerWASP/Configuration_adv.h
+++ b/config/examples/WASP/PowerWASP/Configuration_adv.h
@@ -957,6 +957,8 @@
    */
   #define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     #define POWER_LOSS_PIN           65 // Pin to detect power loss
     #define POWER_LOSS_STATE        LOW // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/Wanhao/Duplicator 6/Configuration_adv.h b/config/examples/Wanhao/Duplicator 6/Configuration_adv.h
index 3ed1cfda89..5a10579859 100644
--- a/config/examples/Wanhao/Duplicator 6/Configuration_adv.h	
+++ b/config/examples/Wanhao/Duplicator 6/Configuration_adv.h	
@@ -959,6 +959,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/Wanhao/Duplicator i3 2.1/Configuration_adv.h b/config/examples/Wanhao/Duplicator i3 2.1/Configuration_adv.h
index 18e29f3cc7..19f4773df0 100644
--- a/config/examples/Wanhao/Duplicator i3 2.1/Configuration_adv.h	
+++ b/config/examples/Wanhao/Duplicator i3 2.1/Configuration_adv.h	
@@ -944,6 +944,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/Wanhao/Duplicator i3 Mini/Configuration_adv.h b/config/examples/Wanhao/Duplicator i3 Mini/Configuration_adv.h
index 0a4ed86749..32859dcc5d 100644
--- a/config/examples/Wanhao/Duplicator i3 Mini/Configuration_adv.h	
+++ b/config/examples/Wanhao/Duplicator i3 Mini/Configuration_adv.h	
@@ -957,6 +957,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/delta/Anycubic/Kossel/Configuration_adv.h b/config/examples/delta/Anycubic/Kossel/Configuration_adv.h
index 7d5e8caeac..23b3ade1e9 100644
--- a/config/examples/delta/Anycubic/Kossel/Configuration_adv.h
+++ b/config/examples/delta/Anycubic/Kossel/Configuration_adv.h
@@ -962,6 +962,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/delta/Dreammaker/Overlord/Configuration_adv.h b/config/examples/delta/Dreammaker/Overlord/Configuration_adv.h
index e4166c9f6e..50d84f2bca 100644
--- a/config/examples/delta/Dreammaker/Overlord/Configuration_adv.h
+++ b/config/examples/delta/Dreammaker/Overlord/Configuration_adv.h
@@ -962,6 +962,8 @@
    */
   #define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss (optional)
     #define POWER_LOSS_STATE        LOW // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/delta/Dreammaker/Overlord_Pro/Configuration_adv.h b/config/examples/delta/Dreammaker/Overlord_Pro/Configuration_adv.h
index 4c453b4d80..3a9b918669 100644
--- a/config/examples/delta/Dreammaker/Overlord_Pro/Configuration_adv.h
+++ b/config/examples/delta/Dreammaker/Overlord_Pro/Configuration_adv.h
@@ -962,6 +962,8 @@
    */
   #define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss (optional)
     #define POWER_LOSS_STATE        LOW // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h b/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h
index 3ba7648aa2..1a51893fbe 100644
--- a/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h
+++ b/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h
@@ -962,6 +962,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/delta/FLSUN/kossel/Configuration_adv.h b/config/examples/delta/FLSUN/kossel/Configuration_adv.h
index 3ba7648aa2..1a51893fbe 100644
--- a/config/examples/delta/FLSUN/kossel/Configuration_adv.h
+++ b/config/examples/delta/FLSUN/kossel/Configuration_adv.h
@@ -962,6 +962,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h b/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h
index 21d3e58d2d..75f07acaa3 100644
--- a/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h
+++ b/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h
@@ -962,6 +962,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h b/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h
index e21716b41c..c391643433 100644
--- a/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h	
+++ b/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h	
@@ -962,6 +962,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/delta/MKS/SBASE/Configuration_adv.h b/config/examples/delta/MKS/SBASE/Configuration_adv.h
index 57ad3a9667..9e82d67e8a 100644
--- a/config/examples/delta/MKS/SBASE/Configuration_adv.h
+++ b/config/examples/delta/MKS/SBASE/Configuration_adv.h
@@ -962,6 +962,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/delta/Tevo Little Monster/Configuration_adv.h b/config/examples/delta/Tevo Little Monster/Configuration_adv.h
index dcd4b09c05..ae43859c99 100644
--- a/config/examples/delta/Tevo Little Monster/Configuration_adv.h	
+++ b/config/examples/delta/Tevo Little Monster/Configuration_adv.h	
@@ -962,6 +962,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/delta/generic/Configuration_adv.h b/config/examples/delta/generic/Configuration_adv.h
index 21d3e58d2d..75f07acaa3 100644
--- a/config/examples/delta/generic/Configuration_adv.h
+++ b/config/examples/delta/generic/Configuration_adv.h
@@ -962,6 +962,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/delta/kossel_mini/Configuration_adv.h b/config/examples/delta/kossel_mini/Configuration_adv.h
index 21d3e58d2d..75f07acaa3 100644
--- a/config/examples/delta/kossel_mini/Configuration_adv.h
+++ b/config/examples/delta/kossel_mini/Configuration_adv.h
@@ -962,6 +962,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/delta/kossel_xl/Configuration_adv.h b/config/examples/delta/kossel_xl/Configuration_adv.h
index 963242d4b8..fdb6a5cf4e 100644
--- a/config/examples/delta/kossel_xl/Configuration_adv.h
+++ b/config/examples/delta/kossel_xl/Configuration_adv.h
@@ -962,6 +962,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/gCreate/gMax1.5+/Configuration_adv.h b/config/examples/gCreate/gMax1.5+/Configuration_adv.h
index de3492070c..701bf80dd7 100644
--- a/config/examples/gCreate/gMax1.5+/Configuration_adv.h
+++ b/config/examples/gCreate/gMax1.5+/Configuration_adv.h
@@ -960,6 +960,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/makibox/Configuration_adv.h b/config/examples/makibox/Configuration_adv.h
index c902408fd1..efdb02d2c2 100644
--- a/config/examples/makibox/Configuration_adv.h
+++ b/config/examples/makibox/Configuration_adv.h
@@ -957,6 +957,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/tvrrug/Round2/Configuration_adv.h b/config/examples/tvrrug/Round2/Configuration_adv.h
index 52045e3835..d3b0595534 100644
--- a/config/examples/tvrrug/Round2/Configuration_adv.h
+++ b/config/examples/tvrrug/Round2/Configuration_adv.h
@@ -957,6 +957,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/wt150/Configuration_adv.h b/config/examples/wt150/Configuration_adv.h
index aa7ba56e6f..35f18aa028 100644
--- a/config/examples/wt150/Configuration_adv.h
+++ b/config/examples/wt150/Configuration_adv.h
@@ -958,6 +958,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate