|
|
|
@ -294,9 +294,9 @@ |
|
|
|
// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
|
|
|
|
// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
|
|
|
|
// For the other hotends it is their distance from the extruder 0 hotend.
|
|
|
|
//#define HOTEND_OFFSET_X {0.0, 20.00} // (mm) relative X-offset for each nozzle
|
|
|
|
//#define HOTEND_OFFSET_Y {0.0, 5.00} // (mm) relative Y-offset for each nozzle
|
|
|
|
//#define HOTEND_OFFSET_Z {0.0, 0.00} // (mm) relative Z-offset for each nozzle
|
|
|
|
//#define HOTEND_OFFSET_X { 0.0, 20.00 } // (mm) relative X-offset for each nozzle
|
|
|
|
//#define HOTEND_OFFSET_Y { 0.0, 5.00 } // (mm) relative Y-offset for each nozzle
|
|
|
|
//#define HOTEND_OFFSET_Z { 0.0, 0.00 } // (mm) relative Z-offset for each nozzle
|
|
|
|
|
|
|
|
// @section machine
|
|
|
|
|
|
|
|
@ -724,8 +724,8 @@ |
|
|
|
|
|
|
|
// ANET A6 Firmwae V2.0 defaults: (steps/mm)
|
|
|
|
// Xsteps/mm: +100.0, Ysteps/mm: +100.0, Zsteps/mm: +0400.0, eSteps/mm: +0095.0
|
|
|
|
#define DEFAULT_AXIS_STEPS_PER_UNIT {100, 100, 400, 95} |
|
|
|
//#define DEFAULT_AXIS_STEPS_PER_UNIT {80, 80, 400, 95}
|
|
|
|
#define DEFAULT_AXIS_STEPS_PER_UNIT { 100, 100, 400, 95 } |
|
|
|
//#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 400, 95 }
|
|
|
|
|
|
|
|
/**
|
|
|
|
* Default Max Feed Rate (mm/s) |
|
|
|
@ -736,8 +736,8 @@ |
|
|
|
|
|
|
|
// ANET A6 Firmware V2.0 defaults (Vmax):
|
|
|
|
// Vmax x: 400, Vmax y: 400, Vmax z: 4, Vmax e: 25
|
|
|
|
#define DEFAULT_MAX_FEEDRATE {400, 400, 4, 25} |
|
|
|
//#define DEFAULT_MAX_FEEDRATE {400, 400, 20, 50}
|
|
|
|
#define DEFAULT_MAX_FEEDRATE { 400, 400, 4, 25 } |
|
|
|
//#define DEFAULT_MAX_FEEDRATE { 400, 400, 20, 50 }
|
|
|
|
|
|
|
|
|
|
|
|
/**
|
|
|
|
@ -868,8 +868,8 @@ |
|
|
|
/**
|
|
|
|
* Z Servo Probe, such as an endstop switch on a rotating arm. |
|
|
|
*/ |
|
|
|
//#define Z_PROBE_SERVO_NR 0 // Defaults to SERVO 0 connector.
|
|
|
|
//#define Z_SERVO_ANGLES {70,0} // Z Servo Deploy and Stow angles
|
|
|
|
//#define Z_PROBE_SERVO_NR 0 // Defaults to SERVO 0 connector.
|
|
|
|
//#define Z_SERVO_ANGLES { 70, 0 } // Z Servo Deploy and Stow angles
|
|
|
|
|
|
|
|
/**
|
|
|
|
* The BLTouch probe uses a Hall effect sensor and emulates a servo. |
|
|
|
@ -1641,7 +1641,7 @@ |
|
|
|
|
|
|
|
// Specify positions as { X, Y, Z }
|
|
|
|
#define NOZZLE_CLEAN_START_POINT { 30, 30, (Z_MIN_POS + 1)} |
|
|
|
#define NOZZLE_CLEAN_END_POINT {100, 60, (Z_MIN_POS + 1)} |
|
|
|
#define NOZZLE_CLEAN_END_POINT { 100, 60, (Z_MIN_POS + 1) } |
|
|
|
|
|
|
|
// Circular pattern radius
|
|
|
|
#define NOZZLE_CLEAN_CIRCLE_RADIUS 6.5 |
|
|
|
|
Scott Lahteine
5 years ago