diff --git a/Marlin/src/HAL/STM32/sdio.cpp b/Marlin/src/HAL/STM32/sdio.cpp index 558cb4686e..4333006713 100644 --- a/Marlin/src/HAL/STM32/sdio.cpp +++ b/Marlin/src/HAL/STM32/sdio.cpp @@ -33,256 +33,410 @@ #include #include -// use local drivers #if defined(STM32F103xE) || defined(STM32F103xG) - #include + #include + #include #elif defined(STM32F4xx) - #include + #include + #include + #include + #include #elif defined(STM32F7xx) - #include + #include + #include + #include + #include #elif defined(STM32H7xx) - #include + #define SDIO_FOR_STM32H7 + #include + #include + #include + #include #else - #error "SDIO only supported with STM32F103xE, STM32F103xG, STM32F4xx, STM32F7xx, or STM32H7xx." + #error "SDIO is only supported with STM32F103xE, STM32F103xG, STM32F4xx, STM32F7xx, and STM32H7xx." #endif +// SDIO Max Clock (naming from STM Manual, don't change) +#define SDIOCLK 48000000 + // Target Clock, configurable. Default is 18MHz, from STM32F1 #ifndef SDIO_CLOCK #define SDIO_CLOCK 18000000 // 18 MHz #endif -#define SD_TIMEOUT 1000 // ms +SD_HandleTypeDef hsd; // SDIO structure -// SDIO Max Clock (naming from STM Manual, don't change) -#define SDIOCLK 48000000 +static uint32_t clock_to_divider(uint32_t clk) { + #ifdef SDIO_FOR_STM32H7 + // SDMMC_CK frequency = sdmmc_ker_ck / [2 * CLKDIV]. + uint32_t sdmmc_clk = HAL_RCCEx_GetPeriphCLKFreq(RCC_PERIPHCLK_SDMMC); + return sdmmc_clk / (2U * SDIO_CLOCK) + (sdmmc_clk % (2U * SDIO_CLOCK) != 0); + #else + // limit the SDIO master clock to 8/3 of PCLK2. See STM32 Manuals + // Also limited to no more than 48Mhz (SDIOCLK). + const uint32_t pclk2 = HAL_RCC_GetPCLK2Freq(); + clk = min(clk, (uint32_t)(pclk2 * 8 / 3)); + clk = min(clk, (uint32_t)SDIOCLK); + // Round up divider, so we don't run the card over the speed supported, + // and subtract by 2, because STM32 will add 2, as written in the manual: + // SDIO_CK frequency = SDIOCLK / [CLKDIV + 2] + return pclk2 / clk + (pclk2 % clk != 0) - 2; + #endif +} -#if defined(STM32F1xx) - DMA_HandleTypeDef hdma_sdio; - extern "C" void DMA2_Channel4_5_IRQHandler(void) { - HAL_DMA_IRQHandler(&hdma_sdio); - } -#elif defined(STM32F4xx) - DMA_HandleTypeDef hdma_sdio_rx; - DMA_HandleTypeDef hdma_sdio_tx; - extern "C" void DMA2_Stream3_IRQHandler(void) { - HAL_DMA_IRQHandler(&hdma_sdio_rx); +// Start the SDIO clock +void HAL_SD_MspInit(SD_HandleTypeDef *hsd) { + UNUSED(hsd); + #ifdef SDIO_FOR_STM32H7 + pinmap_pinout(PC_12, PinMap_SD); + pinmap_pinout(PD_2, PinMap_SD); + pinmap_pinout(PC_8, PinMap_SD); + #if PINS_EXIST(SDIO_D1, SDIO_D2, SDIO_D3) // Define D1-D3 only for 4-bit wide SDIO bus + pinmap_pinout(PC_9, PinMap_SD); + pinmap_pinout(PC_10, PinMap_SD); + pinmap_pinout(PC_11, PinMap_SD); + #endif + __HAL_RCC_SDMMC1_CLK_ENABLE(); + HAL_NVIC_EnableIRQ(SDMMC1_IRQn); + #else + __HAL_RCC_SDIO_CLK_ENABLE(); + #endif +} + +#ifdef SDIO_FOR_STM32H7 + + #define SD_TIMEOUT 1000 // ms + + extern "C" void SDMMC1_IRQHandler(void) { HAL_SD_IRQHandler(&hsd); } + + uint8_t waitingRxCplt = 0, waitingTxCplt = 0; + void HAL_SD_TxCpltCallback(SD_HandleTypeDef *hsdio) { waitingTxCplt = 0; } + void HAL_SD_RxCpltCallback(SD_HandleTypeDef *hsdio) { waitingRxCplt = 0; } + + void HAL_SD_MspDeInit(SD_HandleTypeDef *hsd) { + __HAL_RCC_SDMMC1_FORCE_RESET(); delay(10); + __HAL_RCC_SDMMC1_RELEASE_RESET(); delay(10); } - extern "C" void DMA2_Stream6_IRQHandler(void) { - HAL_DMA_IRQHandler(&hdma_sdio_tx); + bool SDIO_Init() { + HAL_StatusTypeDef sd_state = HAL_OK; + if (hsd.Instance == SDMMC1) HAL_SD_DeInit(&hsd); + + // HAL SD initialization + hsd.Instance = SDMMC1; + hsd.Init.ClockEdge = SDMMC_CLOCK_EDGE_RISING; + hsd.Init.ClockPowerSave = SDMMC_CLOCK_POWER_SAVE_DISABLE; + hsd.Init.BusWide = SDMMC_BUS_WIDE_1B; + hsd.Init.HardwareFlowControl = SDMMC_HARDWARE_FLOW_CONTROL_DISABLE; + hsd.Init.ClockDiv = clock_to_divider(SDIO_CLOCK); + sd_state = HAL_SD_Init(&hsd); + + #if PINS_EXIST(SDIO_D1, SDIO_D2, SDIO_D3) + if (sd_state == HAL_OK) + sd_state = HAL_SD_ConfigWideBusOperation(&hsd, SDMMC_BUS_WIDE_4B); + #endif + + return (sd_state == HAL_OK); } -#elif defined(STM32H7xx) - #define __HAL_RCC_SDIO_FORCE_RESET __HAL_RCC_SDMMC1_FORCE_RESET - #define __HAL_RCC_SDIO_RELEASE_RESET __HAL_RCC_SDMMC1_RELEASE_RESET - #define __HAL_RCC_SDIO_CLK_ENABLE __HAL_RCC_SDMMC1_CLK_ENABLE - #define SDIO SDMMC1 - #define SDIO_IRQn SDMMC1_IRQn - #define SDIO_IRQHandler SDMMC1_IRQHandler - #define SDIO_CLOCK_EDGE_RISING SDMMC_CLOCK_EDGE_RISING - #define SDIO_CLOCK_POWER_SAVE_DISABLE SDMMC_CLOCK_POWER_SAVE_DISABLE - #define SDIO_BUS_WIDE_1B SDMMC_BUS_WIDE_1B - #define SDIO_BUS_WIDE_4B SDMMC_BUS_WIDE_4B - #define SDIO_HARDWARE_FLOW_CONTROL_DISABLE SDMMC_HARDWARE_FLOW_CONTROL_DISABLE -#endif -uint8_t waitingRxCplt = 0; -uint8_t waitingTxCplt = 0; -SD_HandleTypeDef hsd; +#else // !SDIO_FOR_STM32H7 -extern "C" void SDIO_IRQHandler(void) { - HAL_SD_IRQHandler(&hsd); -} + #define SD_TIMEOUT 500 // ms -void HAL_SD_TxCpltCallback(SD_HandleTypeDef *hsdio) { - waitingTxCplt = 0; -} + // SDIO retries, configurable. Default is 3, from STM32F1 + #ifndef SDIO_READ_RETRIES + #define SDIO_READ_RETRIES 3 + #endif -void HAL_SD_RxCpltCallback(SD_HandleTypeDef *hsdio) { - waitingRxCplt = 0; -} + // F4 supports one DMA for RX and another for TX, but Marlin will never + // do read and write at same time, so we use the same DMA for both. + DMA_HandleTypeDef hdma_sdio; -void HAL_SD_MspInit(SD_HandleTypeDef *hsd) { - pinmap_pinout(PC_12, PinMap_SD); - pinmap_pinout(PD_2, PinMap_SD); - pinmap_pinout(PC_8, PinMap_SD); - #if PINS_EXIST(SDIO_D1, SDIO_D2, SDIO_D3) // define D1-D3 only if have a four bit wide SDIO bus - // D1-D3 - pinmap_pinout(PC_9, PinMap_SD); - pinmap_pinout(PC_10, PinMap_SD); - pinmap_pinout(PC_11, PinMap_SD); + #ifdef STM32F1xx + #define DMA_IRQ_HANDLER DMA2_Channel4_5_IRQHandler + #elif defined(STM32F4xx) + #define DMA_IRQ_HANDLER DMA2_Stream3_IRQHandler + #else + #error "Unknown STM32 architecture." #endif - __HAL_RCC_SDIO_CLK_ENABLE(); - HAL_NVIC_EnableIRQ(SDIO_IRQn); + extern "C" void SDIO_IRQHandler(void) { HAL_SD_IRQHandler(&hsd); } + extern "C" void DMA_IRQ_HANDLER(void) { HAL_DMA_IRQHandler(&hdma_sdio); } + + /* + SDIO_INIT_CLK_DIV is 118 + SDIO clock frequency is 48MHz / (TRANSFER_CLOCK_DIV + 2) + SDIO init clock frequency should not exceed 400kHz = 48MHz / (118 + 2) + + Default TRANSFER_CLOCK_DIV is 2 (118 / 40) + Default SDIO clock frequency is 48MHz / (2 + 2) = 12 MHz + This might be too fast for stable SDIO operations + + MKS Robin SDIO seems stable with BusWide 1bit and ClockDiv 8 (i.e., 4.8MHz SDIO clock frequency) + More testing is required as there are clearly some 4bit init problems. + */ + + void go_to_transfer_speed() { + /* Default SDIO peripheral configuration for SD card initialization */ + hsd.Init.ClockEdge = hsd.Init.ClockEdge; + hsd.Init.ClockBypass = hsd.Init.ClockBypass; + hsd.Init.ClockPowerSave = hsd.Init.ClockPowerSave; + hsd.Init.BusWide = hsd.Init.BusWide; + hsd.Init.HardwareFlowControl = hsd.Init.HardwareFlowControl; + hsd.Init.ClockDiv = clock_to_divider(SDIO_CLOCK); + + /* Initialize SDIO peripheral interface with default configuration */ + SDIO_Init(hsd.Instance, hsd.Init); + } - // DMA Config - #if defined(STM32F1xx) - __HAL_RCC_DMA2_CLK_ENABLE(); - HAL_NVIC_EnableIRQ(DMA2_Channel4_5_IRQn); - hdma_sdio.Instance = DMA2_Channel4; - hdma_sdio.Init.Direction = DMA_PERIPH_TO_MEMORY; + void SD_LowLevel_Init() { + uint32_t tempreg; + + // Enable GPIO clocks + __HAL_RCC_GPIOC_CLK_ENABLE(); + __HAL_RCC_GPIOD_CLK_ENABLE(); + + GPIO_InitTypeDef GPIO_InitStruct; + + GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; + GPIO_InitStruct.Pull = 1; // GPIO_NOPULL + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; + + #if DISABLED(STM32F1xx) + GPIO_InitStruct.Alternate = GPIO_AF12_SDIO; + #endif + + GPIO_InitStruct.Pin = GPIO_PIN_8 | GPIO_PIN_12; // D0 & SCK + HAL_GPIO_Init(GPIOC, &GPIO_InitStruct); + + #if PINS_EXIST(SDIO_D1, SDIO_D2, SDIO_D3) // define D1-D3 only if have a four bit wide SDIO bus + GPIO_InitStruct.Pin = GPIO_PIN_9 | GPIO_PIN_10 | GPIO_PIN_11; // D1-D3 + HAL_GPIO_Init(GPIOC, &GPIO_InitStruct); + #endif + + // Configure PD.02 CMD line + GPIO_InitStruct.Pin = GPIO_PIN_2; + HAL_GPIO_Init(GPIOD, &GPIO_InitStruct); + + // Setup DMA + #ifdef STM32F1xx + hdma_sdio.Init.Mode = DMA_NORMAL; + hdma_sdio.Instance = DMA2_Channel4; + HAL_NVIC_EnableIRQ(DMA2_Channel4_5_IRQn); + #elif defined(STM32F4xx) + hdma_sdio.Init.Mode = DMA_PFCTRL; + hdma_sdio.Instance = DMA2_Stream3; + hdma_sdio.Init.Channel = DMA_CHANNEL_4; + hdma_sdio.Init.FIFOMode = DMA_FIFOMODE_ENABLE; + hdma_sdio.Init.FIFOThreshold = DMA_FIFO_THRESHOLD_FULL; + hdma_sdio.Init.MemBurst = DMA_MBURST_INC4; + hdma_sdio.Init.PeriphBurst = DMA_PBURST_INC4; + HAL_NVIC_EnableIRQ(DMA2_Stream3_IRQn); + #endif + HAL_NVIC_EnableIRQ(SDIO_IRQn); hdma_sdio.Init.PeriphInc = DMA_PINC_DISABLE; hdma_sdio.Init.MemInc = DMA_MINC_ENABLE; hdma_sdio.Init.PeriphDataAlignment = DMA_PDATAALIGN_WORD; hdma_sdio.Init.MemDataAlignment = DMA_MDATAALIGN_WORD; - hdma_sdio.Init.Mode = DMA_NORMAL; hdma_sdio.Init.Priority = DMA_PRIORITY_LOW; - HAL_DMA_Init(&hdma_sdio); + __HAL_LINKDMA(&hsd, hdmarx, hdma_sdio); + __HAL_LINKDMA(&hsd, hdmatx, hdma_sdio); + + #ifdef STM32F1xx + __HAL_RCC_SDIO_CLK_ENABLE(); + __HAL_RCC_DMA2_CLK_ENABLE(); + #else + __HAL_RCC_SDIO_FORCE_RESET(); delay(2); + __HAL_RCC_SDIO_RELEASE_RESET(); delay(2); + __HAL_RCC_SDIO_CLK_ENABLE(); + + __HAL_RCC_DMA2_FORCE_RESET(); delay(2); + __HAL_RCC_DMA2_RELEASE_RESET(); delay(2); + __HAL_RCC_DMA2_CLK_ENABLE(); + #endif + + // Initialize the SDIO (with initial <400Khz Clock) + tempreg = 0 // Reset value + | SDIO_CLKCR_CLKEN // Clock enabled + | SDIO_INIT_CLK_DIV; // Clock Divider. Clock = 48000 / (118 + 2) = 400Khz + // Keep the rest at 0 => HW_Flow Disabled, Rising Clock Edge, Disable CLK ByPass, Bus Width = 0, Power save Disable + SDIO->CLKCR = tempreg; + + // Power up the SDIO + SDIO_PowerState_ON(SDIO); + hsd.Instance = SDIO; + } - __HAL_LINKDMA(hsd, hdmarx ,hdma_sdio); - __HAL_LINKDMA(hsd, hdmatx, hdma_sdio); - #elif defined(STM32F4xx) - __HAL_RCC_DMA2_CLK_ENABLE(); - HAL_NVIC_EnableIRQ(DMA2_Stream3_IRQn); - HAL_NVIC_EnableIRQ(DMA2_Stream6_IRQn); - hdma_sdio_rx.Instance = DMA2_Stream3; - hdma_sdio_rx.Init.Channel = DMA_CHANNEL_4; - hdma_sdio_rx.Init.Direction = DMA_PERIPH_TO_MEMORY; - hdma_sdio_rx.Init.PeriphInc = DMA_PINC_DISABLE; - hdma_sdio_rx.Init.MemInc = DMA_MINC_ENABLE; - hdma_sdio_rx.Init.PeriphDataAlignment = DMA_PDATAALIGN_WORD; - hdma_sdio_rx.Init.MemDataAlignment = DMA_MDATAALIGN_WORD; - hdma_sdio_rx.Init.Mode = DMA_PFCTRL; - hdma_sdio_rx.Init.Priority = DMA_PRIORITY_LOW; - hdma_sdio_rx.Init.FIFOMode = DMA_FIFOMODE_ENABLE; - hdma_sdio_rx.Init.FIFOThreshold = DMA_FIFO_THRESHOLD_FULL; - hdma_sdio_rx.Init.MemBurst = DMA_MBURST_INC4; - hdma_sdio_rx.Init.PeriphBurst = DMA_PBURST_INC4; - HAL_DMA_Init(&hdma_sdio_rx); - - __HAL_LINKDMA(hsd,hdmarx,hdma_sdio_rx); - - hdma_sdio_tx.Instance = DMA2_Stream6; - hdma_sdio_tx.Init.Channel = DMA_CHANNEL_4; - hdma_sdio_tx.Init.Direction = DMA_MEMORY_TO_PERIPH; - hdma_sdio_tx.Init.PeriphInc = DMA_PINC_DISABLE; - hdma_sdio_tx.Init.MemInc = DMA_MINC_ENABLE; - hdma_sdio_tx.Init.PeriphDataAlignment = DMA_PDATAALIGN_WORD; - hdma_sdio_tx.Init.MemDataAlignment = DMA_MDATAALIGN_WORD; - hdma_sdio_tx.Init.Mode = DMA_PFCTRL; - hdma_sdio_tx.Init.Priority = DMA_PRIORITY_LOW; - hdma_sdio_tx.Init.FIFOMode = DMA_FIFOMODE_ENABLE; - hdma_sdio_tx.Init.FIFOThreshold = DMA_FIFO_THRESHOLD_FULL; - hdma_sdio_tx.Init.MemBurst = DMA_MBURST_INC4; - hdma_sdio_tx.Init.PeriphBurst = DMA_PBURST_INC4; - HAL_DMA_Init(&hdma_sdio_tx); - - __HAL_LINKDMA(hsd,hdmatx,hdma_sdio_tx); - #endif -} + bool SDIO_Init() { + uint8_t retryCnt = SDIO_READ_RETRIES; -void HAL_SD_MspDeInit(SD_HandleTypeDef *hsd) { - #if !defined(STM32F1xx) - __HAL_RCC_SDIO_FORCE_RESET(); - delay(10); - __HAL_RCC_SDIO_RELEASE_RESET(); - delay(10); - #endif -} + bool status; + hsd.Instance = SDIO; + hsd.State = HAL_SD_STATE_RESET; -static uint32_t clock_to_divider(uint32_t clk) { - #if defined(STM32H7xx) - // SDMMC_CK frequency = sdmmc_ker_ck / [2 * CLKDIV]. - uint32_t sdmmc_clk = HAL_RCCEx_GetPeriphCLKFreq(RCC_PERIPHCLK_SDMMC); - return sdmmc_clk / (2U * SDIO_CLOCK) + (sdmmc_clk % (2U * SDIO_CLOCK) != 0); - #else - // limit the SDIO master clock to 8/3 of PCLK2. See STM32 Manuals - // Also limited to no more than 48Mhz (SDIOCLK). - const uint32_t pclk2 = HAL_RCC_GetPCLK2Freq(); - clk = min(clk, (uint32_t)(pclk2 * 8 / 3)); - clk = min(clk, (uint32_t)SDIOCLK); - // Round up divider, so we don't run the card over the speed supported, - // and subtract by 2, because STM32 will add 2, as written in the manual: - // SDIO_CK frequency = SDIOCLK / [CLKDIV + 2] - return pclk2 / clk + (pclk2 % clk != 0) - 2; - #endif -} + SD_LowLevel_Init(); -bool SDIO_Init() { - HAL_StatusTypeDef sd_state = HAL_OK; - if (hsd.Instance == SDIO) - HAL_SD_DeInit(&hsd); - - /* HAL SD initialization */ - hsd.Instance = SDIO; - hsd.Init.ClockEdge = SDIO_CLOCK_EDGE_RISING; - hsd.Init.ClockPowerSave = SDIO_CLOCK_POWER_SAVE_DISABLE; - hsd.Init.BusWide = SDIO_BUS_WIDE_1B; - hsd.Init.HardwareFlowControl = SDIO_HARDWARE_FLOW_CONTROL_DISABLE; - hsd.Init.ClockDiv = clock_to_divider(SDIO_CLOCK); - sd_state = HAL_SD_Init(&hsd); - - #if PINS_EXIST(SDIO_D1, SDIO_D2, SDIO_D3) - if (sd_state == HAL_OK) { - //sd_state = HAL_SD_ConfigWideBusOperation(&hsd, SDIO_BUS_WIDE_4B); - //Fix 4b sdio - SDIO_InitTypeDef Init; - uint32_t errorstate; - - /* Send CMD55 APP_CMD with argument as card's RCA.*/ - errorstate = SDMMC_CmdAppCommand(hsd.Instance, (uint32_t)(hsd.SdCard.RelCardAdd << 16U)); - if(errorstate != HAL_SD_ERROR_NONE) - { - return false; + uint8_t retry_Cnt = retryCnt; + for (;;) { + hal.watchdog_refresh(); + status = (bool) HAL_SD_Init(&hsd); + if (!status) break; + if (!--retry_Cnt) return false; // return failing status if retries are exhausted + } + + go_to_transfer_speed(); + + #if PINS_EXIST(SDIO_D1, SDIO_D2, SDIO_D3) // go to 4 bit wide mode if pins are defined + retry_Cnt = retryCnt; + for (;;) { + hal.watchdog_refresh(); + if (!HAL_SD_ConfigWideBusOperation(&hsd, SDIO_BUS_WIDE_4B)) break; // some cards are only 1 bit wide so a pass here is not required + if (!--retry_Cnt) break; + } + if (!retry_Cnt) { // wide bus failed, go back to one bit wide mode + hsd.State = (HAL_SD_StateTypeDef) 0; // HAL_SD_STATE_RESET + SD_LowLevel_Init(); + retry_Cnt = retryCnt; + for (;;) { + hal.watchdog_refresh(); + status = (bool) HAL_SD_Init(&hsd); + if (!status) break; + if (!--retry_Cnt) return false; // return failing status if retries are exhausted + } + go_to_transfer_speed(); } + #endif - /* Send ACMD6 APP_CMD with argument as 2 for wide bus mode */ - errorstate = SDMMC_CmdBusWidth(hsd.Instance, 2U); - if(errorstate != HAL_SD_ERROR_NONE) - { + return true; + } + + /** + * @brief Read or Write a block + * @details Read or Write a block with SDIO + * + * @param block The block index + * @param src The data buffer source for a write + * @param dst The data buffer destination for a read + * + * @return true on success + */ + static bool SDIO_ReadWriteBlock_DMA(uint32_t block, const uint8_t *src, uint8_t *dst) { + if (HAL_SD_GetCardState(&hsd) != HAL_SD_CARD_TRANSFER) return false; + + hal.watchdog_refresh(); + + HAL_StatusTypeDef ret; + if (src) { + hdma_sdio.Init.Direction = DMA_MEMORY_TO_PERIPH; + HAL_DMA_Init(&hdma_sdio); + ret = HAL_SD_WriteBlocks_DMA(&hsd, (uint8_t*)src, block, 1); + } + else { + hdma_sdio.Init.Direction = DMA_PERIPH_TO_MEMORY; + HAL_DMA_Init(&hdma_sdio); + ret = HAL_SD_ReadBlocks_DMA(&hsd, (uint8_t*)dst, block, 1); + } + + if (ret != HAL_OK) { + HAL_DMA_Abort_IT(&hdma_sdio); + HAL_DMA_DeInit(&hdma_sdio); + return false; + } + + millis_t timeout = millis() + SD_TIMEOUT; + // Wait the transfer + while (hsd.State != HAL_SD_STATE_READY) { + if (ELAPSED(millis(), timeout)) { + HAL_DMA_Abort_IT(&hdma_sdio); + HAL_DMA_DeInit(&hdma_sdio); return false; } + } - /* Configure the SDIO peripheral */ - Init.ClockEdge = hsd.Init.ClockEdge; - Init.ClockBypass = hsd.Init.ClockBypass; - Init.ClockPowerSave = hsd.Init.ClockPowerSave; - Init.BusWide = SDIO_BUS_WIDE_4B; - Init.HardwareFlowControl = hsd.Init.HardwareFlowControl; - Init.ClockDiv = hsd.Init.ClockDiv; - (void)SDIO_Init(hsd.Instance, Init); - - /* Change State */ - hsd.State = HAL_SD_STATE_READY; - } - #endif + while (__HAL_DMA_GET_FLAG(&hdma_sdio, __HAL_DMA_GET_TC_FLAG_INDEX(&hdma_sdio)) != 0 + || __HAL_DMA_GET_FLAG(&hdma_sdio, __HAL_DMA_GET_TE_FLAG_INDEX(&hdma_sdio)) != 0) { /* nada */ } - return (sd_state == HAL_OK) ? true : false; -} + HAL_DMA_Abort_IT(&hdma_sdio); + HAL_DMA_DeInit(&hdma_sdio); -bool SDIO_ReadBlock(uint32_t block, uint8_t *dst) { - uint32_t timeout = HAL_GetTick() + SD_TIMEOUT; + timeout = millis() + SD_TIMEOUT; + while (HAL_SD_GetCardState(&hsd) != HAL_SD_CARD_TRANSFER) if (ELAPSED(millis(), timeout)) return false; - while (HAL_SD_GetCardState(&hsd) != HAL_SD_CARD_TRANSFER) { - if (HAL_GetTick() >= timeout) return false; + return true; } - waitingRxCplt = 1; - if (HAL_SD_ReadBlocks_DMA(&hsd, (uint8_t *)dst, block, 1) != HAL_OK) - return false; +#endif // !SDIO_FOR_STM32H7 - timeout = HAL_GetTick() + SD_TIMEOUT; - while (waitingRxCplt) - if (HAL_GetTick() >= timeout) return false; +/** + * @brief Read a block + * @details Read a block to media with SDIO + * + * @param block The block index + * @param src The block buffer + * + * @return true on success + */ +bool SDIO_ReadBlock(uint32_t block, uint8_t *dst) { + #ifdef SDIO_FOR_STM32H7 + + uint32_t timeout = HAL_GetTick() + SD_TIMEOUT; + + while (HAL_SD_GetCardState(&hsd) != HAL_SD_CARD_TRANSFER) + if (HAL_GetTick() >= timeout) return false; + + waitingRxCplt = 1; + if (HAL_SD_ReadBlocks_DMA(&hsd, (uint8_t*)dst, block, 1) != HAL_OK) + return false; + + timeout = HAL_GetTick() + SD_TIMEOUT; + while (waitingRxCplt) + if (HAL_GetTick() >= timeout) return false; - return true; + return true; + + #else + + uint8_t retries = SDIO_READ_RETRIES; + while (retries--) if (SDIO_ReadWriteBlock_DMA(block, nullptr, dst)) return true; + return false; + + #endif } +/** + * @brief Write a block + * @details Write a block to media with SDIO + * + * @param block The block index + * @param src The block data + * + * @return true on success + */ bool SDIO_WriteBlock(uint32_t block, const uint8_t *src) { - uint32_t timeout = HAL_GetTick() + SD_TIMEOUT; + #ifdef SDIO_FOR_STM32H7 - while (HAL_SD_GetCardState(&hsd) != HAL_SD_CARD_TRANSFER) - if (HAL_GetTick() >= timeout) return false; + uint32_t timeout = HAL_GetTick() + SD_TIMEOUT; - waitingTxCplt = 1; - if (HAL_SD_WriteBlocks_DMA(&hsd, (uint8_t *)src, block, 1) != HAL_OK) - return false; + while (HAL_SD_GetCardState(&hsd) != HAL_SD_CARD_TRANSFER) + if (HAL_GetTick() >= timeout) return false; + + waitingTxCplt = 1; + if (HAL_SD_WriteBlocks_DMA(&hsd, (uint8_t*)src, block, 1) != HAL_OK) + return false; - timeout = HAL_GetTick() + SD_TIMEOUT; - while (waitingTxCplt) - if (HAL_GetTick() >= timeout) return false; + timeout = HAL_GetTick() + SD_TIMEOUT; + while (waitingTxCplt) + if (HAL_GetTick() >= timeout) return false; - return true; + return true; + + #else + + uint8_t retries = SDIO_READ_RETRIES; + while (retries--) if (SDIO_ReadWriteBlock_DMA(block, src, nullptr)) return true; + return false; + + #endif } bool SDIO_IsReady() {