From a20b7d95812018cb55b2f341455a78dd5e21abf9 Mon Sep 17 00:00:00 2001 From: Roxy-3D Date: Thu, 27 Apr 2017 10:08:33 -0500 Subject: [PATCH] Better tuned Example file for FolgerTech i3-2020 Also setting up Z-Probe on the machine. --- .../FolgerTech-i3-2020/Configuration.h | 31 +++++++++---------- 1 file changed, 15 insertions(+), 16 deletions(-) diff --git a/Marlin/example_configurations/FolgerTech-i3-2020/Configuration.h b/Marlin/example_configurations/FolgerTech-i3-2020/Configuration.h index d6f9970a02..c931585ec2 100644 --- a/Marlin/example_configurations/FolgerTech-i3-2020/Configuration.h +++ b/Marlin/example_configurations/FolgerTech-i3-2020/Configuration.h @@ -87,7 +87,7 @@ // startup. Implementation of an idea by Prof Braino to inform user that any changes made to this // build by the user have been successfully uploaded into firmware. #define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes. -//#define SHOW_BOOTSCREEN +#define SHOW_BOOTSCREEN #define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during bootup in line 1 #define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during bootup in line 2 @@ -347,7 +347,7 @@ // If your configuration is significantly different than this and you don't understand the issues involved, you probably // shouldn't use bed PID until someone else verifies your hardware works. // If this is enabled, find your own PID constants below. -//#define PIDTEMPBED +#define PIDTEMPBED //#define BED_LIMIT_SWITCHING @@ -569,8 +569,8 @@ * NUM_SERVOS also needs to be set. This is found later in this file. Set it to * 1 + the number of other servos in your system. */ -//#define Z_ENDSTOP_SERVO_NR 0 // Defaults to SERVO 0 connector. -//#define Z_SERVO_ANGLES {70,0} // Z Servo Deploy and Stow angles +#define Z_ENDSTOP_SERVO_NR 0 // Defaults to SERVO 0 connector. +#define Z_SERVO_ANGLES {40,85} // Z Servo Deploy and Stow angles /** * The BLTouch probe emulates a servo probe. @@ -622,9 +622,9 @@ * O-- FRONT --+ * (0,0) */ -#define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle] -#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle] -#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle] +#define X_PROBE_OFFSET_FROM_EXTRUDER 38 // X offset: -left +right [of the nozzle] +#define Y_PROBE_OFFSET_FROM_EXTRUDER -7 // Y offset: -front +behind [the nozzle] +#define Z_PROBE_OFFSET_FROM_EXTRUDER -9.65 // Z offset: -below +above [the nozzle] // X and Y axis travel speed (mm/m) between probes #define XY_PROBE_SPEED 7500 @@ -696,7 +696,6 @@ #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN - // Enable Z Probe Repeatability test to see how accurate your probe is #define Z_MIN_PROBE_REPEATABILITY_TEST @@ -775,11 +774,11 @@ // @section machine // Travel limits after homing (units are in mm) -#define X_MIN_POS 0 -#define Y_MIN_POS 0 +#define X_MIN_POS 6 +#define Y_MIN_POS 3 #define Z_MIN_POS 0 -#define X_MAX_POS 203 -#define Y_MAX_POS 180 +#define X_MAX_POS 207 +#define Y_MAX_POS 177 #define Z_MAX_POS 175 // If enabled, axes won't move below MIN_POS in response to movement commands. //#define MIN_SOFTWARE_ENDSTOPS @@ -921,12 +920,12 @@ #define UBL_MESH_INSET 1 // Mesh inset margin on print area #define GRID_MAX_POINTS_X 10 // Don't use more than 15 points per axis, implementation limited. #define GRID_MAX_POINTS_Y 10 - #define UBL_PROBE_PT_1_X 39 // These set the probe locations for when UBL does a 3-Point leveling + #define UBL_PROBE_PT_1_X 45 // These set the probe locations for when UBL does a 3-Point leveling #define UBL_PROBE_PT_1_Y 170 // of the mesh. - #define UBL_PROBE_PT_2_X 39 - #define UBL_PROBE_PT_2_Y 20 + #define UBL_PROBE_PT_2_X 45 + #define UBL_PROBE_PT_2_Y 25 #define UBL_PROBE_PT_3_X 180 - #define UBL_PROBE_PT_3_Y 20 + #define UBL_PROBE_PT_3_Y 25 #define UBL_G26_MESH_EDITING // Enable G26 mesh editing #elif ENABLED(MESH_BED_LEVELING)