diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h
index 6f722714ca..1c217ba37a 100644
--- a/Marlin/Configuration.h
+++ b/Marlin/Configuration.h
@@ -1181,6 +1181,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/default/Configuration.h b/Marlin/src/config/default/Configuration.h
index 6f722714ca..1c217ba37a 100644
--- a/Marlin/src/config/default/Configuration.h
+++ b/Marlin/src/config/default/Configuration.h
@@ -1181,6 +1181,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration.h b/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration.h
index 23bd05f4bd..01f3899683 100644
--- a/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration.h
+++ b/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration.h
@@ -1201,6 +1201,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/AliExpress/CL-260/Configuration.h b/Marlin/src/config/examples/AliExpress/CL-260/Configuration.h
index e53f2fb10b..fcdf603a36 100644
--- a/Marlin/src/config/examples/AliExpress/CL-260/Configuration.h
+++ b/Marlin/src/config/examples/AliExpress/CL-260/Configuration.h
@@ -1181,6 +1181,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/Anet/A2/Configuration.h b/Marlin/src/config/examples/Anet/A2/Configuration.h
index b5094adb97..c4a3d9f963 100644
--- a/Marlin/src/config/examples/Anet/A2/Configuration.h
+++ b/Marlin/src/config/examples/Anet/A2/Configuration.h
@@ -1181,6 +1181,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/Anet/A2plus/Configuration.h b/Marlin/src/config/examples/Anet/A2plus/Configuration.h
index 3dc67ec384..d94d99f383 100644
--- a/Marlin/src/config/examples/Anet/A2plus/Configuration.h
+++ b/Marlin/src/config/examples/Anet/A2plus/Configuration.h
@@ -1181,6 +1181,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/Anet/A6/Configuration.h b/Marlin/src/config/examples/Anet/A6/Configuration.h
index 1c52d31f4a..03455faa1a 100644
--- a/Marlin/src/config/examples/Anet/A6/Configuration.h
+++ b/Marlin/src/config/examples/Anet/A6/Configuration.h
@@ -1319,6 +1319,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/Anet/A8/Configuration.h b/Marlin/src/config/examples/Anet/A8/Configuration.h
index 88dc9fbd9e..65cc9574d4 100644
--- a/Marlin/src/config/examples/Anet/A8/Configuration.h
+++ b/Marlin/src/config/examples/Anet/A8/Configuration.h
@@ -1194,6 +1194,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/ArmEd/Configuration.h b/Marlin/src/config/examples/ArmEd/Configuration.h
index 72921111d2..b9ecefef9b 100644
--- a/Marlin/src/config/examples/ArmEd/Configuration.h
+++ b/Marlin/src/config/examples/ArmEd/Configuration.h
@@ -1193,6 +1193,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/Azteeg/X5GT/Configuration.h b/Marlin/src/config/examples/Azteeg/X5GT/Configuration.h
index ccc791f628..f704db110c 100644
--- a/Marlin/src/config/examples/Azteeg/X5GT/Configuration.h
+++ b/Marlin/src/config/examples/Azteeg/X5GT/Configuration.h
@@ -1181,6 +1181,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration.h b/Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration.h
index bbee93ffcc..f086b85f46 100644
--- a/Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration.h
+++ b/Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration.h
@@ -1181,6 +1181,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/BIBO/TouchX/default/Configuration.h b/Marlin/src/config/examples/BIBO/TouchX/default/Configuration.h
index 4f4346a6d1..59d6e72a80 100644
--- a/Marlin/src/config/examples/BIBO/TouchX/default/Configuration.h
+++ b/Marlin/src/config/examples/BIBO/TouchX/default/Configuration.h
@@ -1181,6 +1181,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/BQ/Hephestos/Configuration.h b/Marlin/src/config/examples/BQ/Hephestos/Configuration.h
index eb29efce1c..72f5e66513 100644
--- a/Marlin/src/config/examples/BQ/Hephestos/Configuration.h
+++ b/Marlin/src/config/examples/BQ/Hephestos/Configuration.h
@@ -1169,6 +1169,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/BQ/Hephestos_2/Configuration.h b/Marlin/src/config/examples/BQ/Hephestos_2/Configuration.h
index 34088b6523..fe7f7d8997 100644
--- a/Marlin/src/config/examples/BQ/Hephestos_2/Configuration.h
+++ b/Marlin/src/config/examples/BQ/Hephestos_2/Configuration.h
@@ -1181,6 +1181,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/BQ/WITBOX/Configuration.h b/Marlin/src/config/examples/BQ/WITBOX/Configuration.h
index 4903a06954..3d8ccbb5db 100644
--- a/Marlin/src/config/examples/BQ/WITBOX/Configuration.h
+++ b/Marlin/src/config/examples/BQ/WITBOX/Configuration.h
@@ -1169,6 +1169,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/Cartesio/Configuration.h b/Marlin/src/config/examples/Cartesio/Configuration.h
index 1dfb0729ab..cc40f4ca68 100644
--- a/Marlin/src/config/examples/Cartesio/Configuration.h
+++ b/Marlin/src/config/examples/Cartesio/Configuration.h
@@ -1180,6 +1180,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/Creality/CR-10/Configuration.h b/Marlin/src/config/examples/Creality/CR-10/Configuration.h
index 0d14cb0f3d..3f97f0bbdb 100755
--- a/Marlin/src/config/examples/Creality/CR-10/Configuration.h
+++ b/Marlin/src/config/examples/Creality/CR-10/Configuration.h
@@ -1191,6 +1191,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/Creality/CR-10S/Configuration.h b/Marlin/src/config/examples/Creality/CR-10S/Configuration.h
index 8dc44c8a1b..7a7e9fed6b 100644
--- a/Marlin/src/config/examples/Creality/CR-10S/Configuration.h
+++ b/Marlin/src/config/examples/Creality/CR-10S/Configuration.h
@@ -1182,6 +1182,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/Creality/CR-10mini/Configuration.h b/Marlin/src/config/examples/Creality/CR-10mini/Configuration.h
index 537b644a32..25df8a90c1 100644
--- a/Marlin/src/config/examples/Creality/CR-10mini/Configuration.h
+++ b/Marlin/src/config/examples/Creality/CR-10mini/Configuration.h
@@ -1200,6 +1200,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/Creality/CR-8/Configuration.h b/Marlin/src/config/examples/Creality/CR-8/Configuration.h
index ffa28d181e..b519d775af 100644
--- a/Marlin/src/config/examples/Creality/CR-8/Configuration.h
+++ b/Marlin/src/config/examples/Creality/CR-8/Configuration.h
@@ -1191,6 +1191,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/Creality/Ender-2/Configuration.h b/Marlin/src/config/examples/Creality/Ender-2/Configuration.h
index 0aaffdb3e2..62a115de1a 100644
--- a/Marlin/src/config/examples/Creality/Ender-2/Configuration.h
+++ b/Marlin/src/config/examples/Creality/Ender-2/Configuration.h
@@ -1185,6 +1185,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/Creality/Ender-3/Configuration.h b/Marlin/src/config/examples/Creality/Ender-3/Configuration.h
index cc7e3c6cd4..b2951032cd 100644
--- a/Marlin/src/config/examples/Creality/Ender-3/Configuration.h
+++ b/Marlin/src/config/examples/Creality/Ender-3/Configuration.h
@@ -1185,6 +1185,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/Creality/Ender-4/Configuration.h b/Marlin/src/config/examples/Creality/Ender-4/Configuration.h
index 5e56e80dab..9e9be1c820 100644
--- a/Marlin/src/config/examples/Creality/Ender-4/Configuration.h
+++ b/Marlin/src/config/examples/Creality/Ender-4/Configuration.h
@@ -1191,6 +1191,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/Einstart-S/Configuration.h b/Marlin/src/config/examples/Einstart-S/Configuration.h
index efab082def..c732b5feeb 100644
--- a/Marlin/src/config/examples/Einstart-S/Configuration.h
+++ b/Marlin/src/config/examples/Einstart-S/Configuration.h
@@ -1191,6 +1191,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/Felix/Configuration.h b/Marlin/src/config/examples/Felix/Configuration.h
index 4a6425cdba..666e65c374 100644
--- a/Marlin/src/config/examples/Felix/Configuration.h
+++ b/Marlin/src/config/examples/Felix/Configuration.h
@@ -1163,6 +1163,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/Felix/DUAL/Configuration.h b/Marlin/src/config/examples/Felix/DUAL/Configuration.h
index 6e8fd2b48e..19a63a0f54 100644
--- a/Marlin/src/config/examples/Felix/DUAL/Configuration.h
+++ b/Marlin/src/config/examples/Felix/DUAL/Configuration.h
@@ -1163,6 +1163,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration.h b/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration.h
index c25ad304a0..763eaf244b 100644
--- a/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration.h
+++ b/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration.h
@@ -1187,6 +1187,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/Formbot/Raptor/Configuration.h b/Marlin/src/config/examples/Formbot/Raptor/Configuration.h
index 87635af120..53a281a987 100644
--- a/Marlin/src/config/examples/Formbot/Raptor/Configuration.h
+++ b/Marlin/src/config/examples/Formbot/Raptor/Configuration.h
@@ -1286,6 +1286,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/Formbot/T_Rex_2+/Configuration.h b/Marlin/src/config/examples/Formbot/T_Rex_2+/Configuration.h
index 6f7b286c87..ab18b231ea 100644
--- a/Marlin/src/config/examples/Formbot/T_Rex_2+/Configuration.h
+++ b/Marlin/src/config/examples/Formbot/T_Rex_2+/Configuration.h
@@ -1216,6 +1216,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/Formbot/T_Rex_3/Configuration.h b/Marlin/src/config/examples/Formbot/T_Rex_3/Configuration.h
index c0f52b2a7a..f0027c2f84 100644
--- a/Marlin/src/config/examples/Formbot/T_Rex_3/Configuration.h
+++ b/Marlin/src/config/examples/Formbot/T_Rex_3/Configuration.h
@@ -1206,6 +1206,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/Geeetech/GT2560/Configuration.h b/Marlin/src/config/examples/Geeetech/GT2560/Configuration.h
index d789606957..092a51c1d5 100644
--- a/Marlin/src/config/examples/Geeetech/GT2560/Configuration.h
+++ b/Marlin/src/config/examples/Geeetech/GT2560/Configuration.h
@@ -1196,6 +1196,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h b/Marlin/src/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h
index c1225b9c8b..71e38598da 100644
--- a/Marlin/src/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h
+++ b/Marlin/src/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h
@@ -1181,6 +1181,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/Geeetech/MeCreator2/Configuration.h b/Marlin/src/config/examples/Geeetech/MeCreator2/Configuration.h
index 8d51028303..1189ac1a86 100644
--- a/Marlin/src/config/examples/Geeetech/MeCreator2/Configuration.h
+++ b/Marlin/src/config/examples/Geeetech/MeCreator2/Configuration.h
@@ -1188,6 +1188,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h b/Marlin/src/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h
index 631209d201..a9e9d72f6c 100644
--- a/Marlin/src/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h	
+++ b/Marlin/src/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h	
@@ -1197,6 +1197,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h b/Marlin/src/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h
index b41a0e009b..6c6871b454 100644
--- a/Marlin/src/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h	
+++ b/Marlin/src/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h	
@@ -1196,6 +1196,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h b/Marlin/src/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h
index 0d874185b3..9a3d4f8664 100644
--- a/Marlin/src/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h	
+++ b/Marlin/src/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h	
@@ -1181,6 +1181,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h b/Marlin/src/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h
index 799dea79e4..1a9f9ee8b9 100644
--- a/Marlin/src/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h	
+++ b/Marlin/src/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h	
@@ -1181,6 +1181,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/Infitary/i3-M508/Configuration.h b/Marlin/src/config/examples/Infitary/i3-M508/Configuration.h
index 4155b8f811..dd475189e6 100644
--- a/Marlin/src/config/examples/Infitary/i3-M508/Configuration.h
+++ b/Marlin/src/config/examples/Infitary/i3-M508/Configuration.h
@@ -1185,6 +1185,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/JGAurora/A5/Configuration.h b/Marlin/src/config/examples/JGAurora/A5/Configuration.h
index f4c1a398b4..4262a99251 100644
--- a/Marlin/src/config/examples/JGAurora/A5/Configuration.h
+++ b/Marlin/src/config/examples/JGAurora/A5/Configuration.h
@@ -1193,6 +1193,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/MakerParts/Configuration.h b/Marlin/src/config/examples/MakerParts/Configuration.h
index f9698bee4c..1449ac8c06 100644
--- a/Marlin/src/config/examples/MakerParts/Configuration.h
+++ b/Marlin/src/config/examples/MakerParts/Configuration.h
@@ -1201,6 +1201,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/Malyan/M150/Configuration.h b/Marlin/src/config/examples/Malyan/M150/Configuration.h
index 14773ab541..f850719d88 100644
--- a/Marlin/src/config/examples/Malyan/M150/Configuration.h
+++ b/Marlin/src/config/examples/Malyan/M150/Configuration.h
@@ -1209,6 +1209,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/Malyan/M200/Configuration.h b/Marlin/src/config/examples/Malyan/M200/Configuration.h
index 839fb9a878..f9efa57ac8 100644
--- a/Marlin/src/config/examples/Malyan/M200/Configuration.h
+++ b/Marlin/src/config/examples/Malyan/M200/Configuration.h
@@ -1180,6 +1180,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/Micromake/C1/basic/Configuration.h b/Marlin/src/config/examples/Micromake/C1/basic/Configuration.h
index f078e602db..8ce483f3d8 100644
--- a/Marlin/src/config/examples/Micromake/C1/basic/Configuration.h
+++ b/Marlin/src/config/examples/Micromake/C1/basic/Configuration.h
@@ -1185,6 +1185,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration.h b/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration.h
index 9fd7edefee..198da19109 100644
--- a/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration.h
+++ b/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration.h
@@ -1185,6 +1185,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/Mks/Robin/Configuration.h b/Marlin/src/config/examples/Mks/Robin/Configuration.h
index d981f821a5..48f549782a 100644
--- a/Marlin/src/config/examples/Mks/Robin/Configuration.h
+++ b/Marlin/src/config/examples/Mks/Robin/Configuration.h
@@ -1182,6 +1182,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/Mks/Sbase/Configuration.h b/Marlin/src/config/examples/Mks/Sbase/Configuration.h
index 0930fbe49a..effe65ab9f 100644
--- a/Marlin/src/config/examples/Mks/Sbase/Configuration.h
+++ b/Marlin/src/config/examples/Mks/Sbase/Configuration.h
@@ -1181,6 +1181,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/RepRapPro/Huxley/Configuration.h b/Marlin/src/config/examples/RepRapPro/Huxley/Configuration.h
index 0c317a5848..bc5dfd13ab 100644
--- a/Marlin/src/config/examples/RepRapPro/Huxley/Configuration.h
+++ b/Marlin/src/config/examples/RepRapPro/Huxley/Configuration.h
@@ -1230,6 +1230,7 @@ Black rubber belt(MXL), 18 - tooth aluminium pulley : 87.489 step per mm (Huxley
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/RepRapWorld/Megatronics/Configuration.h b/Marlin/src/config/examples/RepRapWorld/Megatronics/Configuration.h
index 87ee0ca9c4..a0e9c8d391 100644
--- a/Marlin/src/config/examples/RepRapWorld/Megatronics/Configuration.h
+++ b/Marlin/src/config/examples/RepRapWorld/Megatronics/Configuration.h
@@ -1181,6 +1181,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/RigidBot/Configuration.h b/Marlin/src/config/examples/RigidBot/Configuration.h
index dc68e13d6e..f51b28e2ed 100644
--- a/Marlin/src/config/examples/RigidBot/Configuration.h
+++ b/Marlin/src/config/examples/RigidBot/Configuration.h
@@ -1179,6 +1179,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/SCARA/Configuration.h b/Marlin/src/config/examples/SCARA/Configuration.h
index 4deb779eac..c4b0be0e25 100644
--- a/Marlin/src/config/examples/SCARA/Configuration.h
+++ b/Marlin/src/config/examples/SCARA/Configuration.h
@@ -1194,6 +1194,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/STM32F10/Configuration.h b/Marlin/src/config/examples/STM32F10/Configuration.h
index 03c5265ab4..2e640ff639 100644
--- a/Marlin/src/config/examples/STM32F10/Configuration.h
+++ b/Marlin/src/config/examples/STM32F10/Configuration.h
@@ -1183,6 +1183,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/STM32F4/Configuration.h b/Marlin/src/config/examples/STM32F4/Configuration.h
index ffb4feeae1..5da61c9bcc 100644
--- a/Marlin/src/config/examples/STM32F4/Configuration.h
+++ b/Marlin/src/config/examples/STM32F4/Configuration.h
@@ -1181,6 +1181,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/Sanguinololu/Configuration.h b/Marlin/src/config/examples/Sanguinololu/Configuration.h
index f4f2746bb6..dc09359a67 100644
--- a/Marlin/src/config/examples/Sanguinololu/Configuration.h
+++ b/Marlin/src/config/examples/Sanguinololu/Configuration.h
@@ -1212,6 +1212,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/TheBorg/Configuration.h b/Marlin/src/config/examples/TheBorg/Configuration.h
index 9a735d83a8..e51046d969 100644
--- a/Marlin/src/config/examples/TheBorg/Configuration.h
+++ b/Marlin/src/config/examples/TheBorg/Configuration.h
@@ -1181,6 +1181,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/TinyBoy2/Configuration.h b/Marlin/src/config/examples/TinyBoy2/Configuration.h
index 7ba6877326..350d2e3b98 100644
--- a/Marlin/src/config/examples/TinyBoy2/Configuration.h
+++ b/Marlin/src/config/examples/TinyBoy2/Configuration.h
@@ -1237,6 +1237,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/Tronxy/X1/Configuration.h b/Marlin/src/config/examples/Tronxy/X1/Configuration.h
index 3e87c2f0ed..8ee968c103 100644
--- a/Marlin/src/config/examples/Tronxy/X1/Configuration.h
+++ b/Marlin/src/config/examples/Tronxy/X1/Configuration.h
@@ -1181,6 +1181,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/Tronxy/X3A/Configuration.h b/Marlin/src/config/examples/Tronxy/X3A/Configuration.h
index a0d2107fbc..76b13d3767 100644
--- a/Marlin/src/config/examples/Tronxy/X3A/Configuration.h
+++ b/Marlin/src/config/examples/Tronxy/X3A/Configuration.h
@@ -1185,6 +1185,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/Tronxy/X5S/Configuration.h b/Marlin/src/config/examples/Tronxy/X5S/Configuration.h
index e7f32ef694..fbe1027d5b 100644
--- a/Marlin/src/config/examples/Tronxy/X5S/Configuration.h
+++ b/Marlin/src/config/examples/Tronxy/X5S/Configuration.h
@@ -1181,6 +1181,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/Tronxy/XY100/Configuration.h b/Marlin/src/config/examples/Tronxy/XY100/Configuration.h
index b932f1e7b0..c022b68a82 100644
--- a/Marlin/src/config/examples/Tronxy/XY100/Configuration.h
+++ b/Marlin/src/config/examples/Tronxy/XY100/Configuration.h
@@ -1192,6 +1192,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/UltiMachine/Archim1/Configuration.h b/Marlin/src/config/examples/UltiMachine/Archim1/Configuration.h
index 8edbafe432..bc322e86e8 100644
--- a/Marlin/src/config/examples/UltiMachine/Archim1/Configuration.h
+++ b/Marlin/src/config/examples/UltiMachine/Archim1/Configuration.h
@@ -1181,6 +1181,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/UltiMachine/Archim2/Configuration.h b/Marlin/src/config/examples/UltiMachine/Archim2/Configuration.h
index e144765503..2f3ee4d849 100644
--- a/Marlin/src/config/examples/UltiMachine/Archim2/Configuration.h
+++ b/Marlin/src/config/examples/UltiMachine/Archim2/Configuration.h
@@ -1181,6 +1181,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/VORONDesign/Configuration.h b/Marlin/src/config/examples/VORONDesign/Configuration.h
index 816f56ce00..cb062ef580 100644
--- a/Marlin/src/config/examples/VORONDesign/Configuration.h
+++ b/Marlin/src/config/examples/VORONDesign/Configuration.h
@@ -1190,6 +1190,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/Velleman/K8200/Configuration.h b/Marlin/src/config/examples/Velleman/K8200/Configuration.h
index d35442c261..d3f10a0709 100644
--- a/Marlin/src/config/examples/Velleman/K8200/Configuration.h
+++ b/Marlin/src/config/examples/Velleman/K8200/Configuration.h
@@ -1211,6 +1211,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/Velleman/K8400/Configuration.h b/Marlin/src/config/examples/Velleman/K8400/Configuration.h
index e400c389c1..def3e65983 100644
--- a/Marlin/src/config/examples/Velleman/K8400/Configuration.h
+++ b/Marlin/src/config/examples/Velleman/K8400/Configuration.h
@@ -1181,6 +1181,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/Velleman/K8400/Dual-head/Configuration.h b/Marlin/src/config/examples/Velleman/K8400/Dual-head/Configuration.h
index a9721054cf..87a6af28b5 100644
--- a/Marlin/src/config/examples/Velleman/K8400/Dual-head/Configuration.h
+++ b/Marlin/src/config/examples/Velleman/K8400/Dual-head/Configuration.h
@@ -1181,6 +1181,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/Wanhao/Duplicator 6/Configuration.h b/Marlin/src/config/examples/Wanhao/Duplicator 6/Configuration.h
index f834dc932d..742e3c83bf 100644
--- a/Marlin/src/config/examples/Wanhao/Duplicator 6/Configuration.h	
+++ b/Marlin/src/config/examples/Wanhao/Duplicator 6/Configuration.h	
@@ -1191,6 +1191,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/adafruit/ST7565/Configuration.h b/Marlin/src/config/examples/adafruit/ST7565/Configuration.h
index e2827b7513..b67aa21216 100644
--- a/Marlin/src/config/examples/adafruit/ST7565/Configuration.h
+++ b/Marlin/src/config/examples/adafruit/ST7565/Configuration.h
@@ -1181,6 +1181,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/delta/Anycubic/Kossel/Configuration.h b/Marlin/src/config/examples/delta/Anycubic/Kossel/Configuration.h
index a4d11d46ed..0b456fc07e 100644
--- a/Marlin/src/config/examples/delta/Anycubic/Kossel/Configuration.h
+++ b/Marlin/src/config/examples/delta/Anycubic/Kossel/Configuration.h
@@ -1372,6 +1372,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration.h b/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration.h
index bd0293a20e..db51df5dba 100644
--- a/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration.h
+++ b/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration.h
@@ -1310,6 +1310,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/delta/FLSUN/kossel/Configuration.h b/Marlin/src/config/examples/delta/FLSUN/kossel/Configuration.h
index 5cec8860a7..361fbed4fb 100644
--- a/Marlin/src/config/examples/delta/FLSUN/kossel/Configuration.h
+++ b/Marlin/src/config/examples/delta/FLSUN/kossel/Configuration.h
@@ -1309,6 +1309,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration.h b/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration.h
index 0d7e928cb2..5fe046503f 100644
--- a/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration.h
+++ b/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration.h
@@ -1309,6 +1309,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/delta/Geeetech/Rostock 301/Configuration.h b/Marlin/src/config/examples/delta/Geeetech/Rostock 301/Configuration.h
index 740cdb1001..9a32647e8c 100644
--- a/Marlin/src/config/examples/delta/Geeetech/Rostock 301/Configuration.h	
+++ b/Marlin/src/config/examples/delta/Geeetech/Rostock 301/Configuration.h	
@@ -1311,6 +1311,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/delta/Hatchbox_Alpha/Configuration.h b/Marlin/src/config/examples/delta/Hatchbox_Alpha/Configuration.h
index c95f970379..d092b2ab26 100644
--- a/Marlin/src/config/examples/delta/Hatchbox_Alpha/Configuration.h
+++ b/Marlin/src/config/examples/delta/Hatchbox_Alpha/Configuration.h
@@ -1312,6 +1312,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/delta/MKS/SBASE/Configuration.h b/Marlin/src/config/examples/delta/MKS/SBASE/Configuration.h
index 6f4b1dc010..d7459fc9de 100644
--- a/Marlin/src/config/examples/delta/MKS/SBASE/Configuration.h
+++ b/Marlin/src/config/examples/delta/MKS/SBASE/Configuration.h
@@ -1297,6 +1297,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/delta/Tevo Little Monster/Configuration.h b/Marlin/src/config/examples/delta/Tevo Little Monster/Configuration.h
index 5a2d09de91..dc900dec29 100644
--- a/Marlin/src/config/examples/delta/Tevo Little Monster/Configuration.h	
+++ b/Marlin/src/config/examples/delta/Tevo Little Monster/Configuration.h	
@@ -1301,6 +1301,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/delta/generic/Configuration.h b/Marlin/src/config/examples/delta/generic/Configuration.h
index 0afc8f099e..934cd9c84a 100644
--- a/Marlin/src/config/examples/delta/generic/Configuration.h
+++ b/Marlin/src/config/examples/delta/generic/Configuration.h
@@ -1297,6 +1297,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/delta/kossel_mini/Configuration.h b/Marlin/src/config/examples/delta/kossel_mini/Configuration.h
index ac4c9e0685..1b12ee84e7 100644
--- a/Marlin/src/config/examples/delta/kossel_mini/Configuration.h
+++ b/Marlin/src/config/examples/delta/kossel_mini/Configuration.h
@@ -1299,6 +1299,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/delta/kossel_pro/Configuration.h b/Marlin/src/config/examples/delta/kossel_pro/Configuration.h
index 212d607aec..864b6ef85c 100644
--- a/Marlin/src/config/examples/delta/kossel_pro/Configuration.h
+++ b/Marlin/src/config/examples/delta/kossel_pro/Configuration.h
@@ -1300,6 +1300,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/delta/kossel_xl/Configuration.h b/Marlin/src/config/examples/delta/kossel_xl/Configuration.h
index 52b08dea6d..c5c4d79c53 100644
--- a/Marlin/src/config/examples/delta/kossel_xl/Configuration.h
+++ b/Marlin/src/config/examples/delta/kossel_xl/Configuration.h
@@ -1300,6 +1300,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration.h b/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration.h
index ef68bfac32..8117e36bd9 100644
--- a/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration.h
+++ b/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration.h
@@ -1195,6 +1195,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/makibox/Configuration.h b/Marlin/src/config/examples/makibox/Configuration.h
index 674ad33825..fda77fda48 100644
--- a/Marlin/src/config/examples/makibox/Configuration.h
+++ b/Marlin/src/config/examples/makibox/Configuration.h
@@ -1184,6 +1184,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/stm32f103ret6/Configuration.h b/Marlin/src/config/examples/stm32f103ret6/Configuration.h
index cd897f062d..f16fd8bcaf 100644
--- a/Marlin/src/config/examples/stm32f103ret6/Configuration.h
+++ b/Marlin/src/config/examples/stm32f103ret6/Configuration.h
@@ -1183,6 +1183,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/tvrrug/Round2/Configuration.h b/Marlin/src/config/examples/tvrrug/Round2/Configuration.h
index 39778186b6..d7ed61ade5 100644
--- a/Marlin/src/config/examples/tvrrug/Round2/Configuration.h
+++ b/Marlin/src/config/examples/tvrrug/Round2/Configuration.h
@@ -1176,6 +1176,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/config/examples/wt150/Configuration.h b/Marlin/src/config/examples/wt150/Configuration.h
index 92d0a05b4c..8dc2568e30 100644
--- a/Marlin/src/config/examples/wt150/Configuration.h
+++ b/Marlin/src/config/examples/wt150/Configuration.h
@@ -1186,6 +1186,7 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/Marlin/src/lcd/menu/menu.h b/Marlin/src/lcd/menu/menu.h
index 7044bd22ca..5646153c49 100644
--- a/Marlin/src/lcd/menu/menu.h
+++ b/Marlin/src/lcd/menu/menu.h
@@ -154,8 +154,8 @@ template<typename NAME>
 class TMenuItem : MenuItemBase {
   private:
     typedef typename NAME::type_t type_t;
-    inline static float unscale(const float value)    { return value * (1.0f / NAME::scale);  }
-    inline static float scale(const float value)      { return value * NAME::scale;           }
+    static inline float unscale(const float value)    { return value * (1.0f / NAME::scale);  }
+    static inline float scale(const float value)      { return value * NAME::scale;           }
     static void  load(void *ptr, const int32_t value) { *((type_t*)ptr) = unscale(value);     }
     static char* to_string(const int32_t value)       { return NAME::strfunc(unscale(value)); }
   public:
diff --git a/Marlin/src/lcd/menu/menu_bed_corners.cpp b/Marlin/src/lcd/menu/menu_bed_corners.cpp
index 037d6be03a..eeb660a4ea 100644
--- a/Marlin/src/lcd/menu/menu_bed_corners.cpp
+++ b/Marlin/src/lcd/menu/menu_bed_corners.cpp
@@ -32,12 +32,18 @@
 #include "../../module/motion.h"
 #include "../../module/planner.h"
 
+#ifndef LEVEL_CORNERS_Z_HOP
+  #define LEVEL_CORNERS_Z_HOP 4.0
+#endif
+
+static_assert(LEVEL_CORNERS_Z_HOP >= 0, "LEVEL_CORNERS_Z_HOP must be >= 0. Please update your configuration.");
+
 /**
  * Level corners, starting in the front-left corner.
  */
 static int8_t bed_corner;
 void _lcd_goto_next_corner() {
-  line_to_z(4.0);
+  line_to_z(LEVEL_CORNERS_Z_HOP);
   switch (bed_corner) {
     case 0:
       current_position[X_AXIS] = X_MIN_BED + LEVEL_CORNERS_INSET;