Apply #pragma once to configuration files

6 years ago · 9e663a624b
136 changed files with 136 additions and 544 deletions
--- a/Marlin/Configuration.h
+++ b/Marlin/Configuration.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration.h
@ -35,8 +36,6 @@
 * Advanced settings can be found in Configuration_adv.h
 *
 */
-#ifndef CONFIGURATION_H
-#define CONFIGURATION_H
 #define CONFIGURATION_H_VERSION 020000

 //===========================================================================
@ -2031,5 +2030,3 @@

 // Allow servo angle to be edited and saved to EEPROM
 //#define EDITABLE_SERVO_ANGLES
-
-#endif // CONFIGURATION_H
--- a/Marlin/Configuration_adv.h
+++ b/Marlin/Configuration_adv.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration_adv.h
@ -30,8 +31,6 @@
 * Basic settings can be found in Configuration.h
 *
 */
-#ifndef CONFIGURATION_ADV_H
-#define CONFIGURATION_ADV_H
 #define CONFIGURATION_ADV_H_VERSION 020000

 // @section temperature
@ -1831,5 +1830,3 @@

 // Enable Marlin dev mode which adds some special commands
 //#define MARLIN_DEV_MODE
-
-#endif // CONFIGURATION_ADV_H
--- a/Marlin/src/config/default/Configuration.h
+++ b/Marlin/src/config/default/Configuration.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration.h
@ -35,8 +36,6 @@
 * Advanced settings can be found in Configuration_adv.h
 *
 */
-#ifndef CONFIGURATION_H
-#define CONFIGURATION_H
 #define CONFIGURATION_H_VERSION 020000

 //===========================================================================
@ -2031,5 +2030,3 @@

 // Allow servo angle to be edited and saved to EEPROM
 //#define EDITABLE_SERVO_ANGLES
-
-#endif // CONFIGURATION_H
--- a/Marlin/src/config/default/Configuration_adv.h
+++ b/Marlin/src/config/default/Configuration_adv.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration_adv.h
@ -30,8 +31,6 @@
 * Basic settings can be found in Configuration.h
 *
 */
-#ifndef CONFIGURATION_ADV_H
-#define CONFIGURATION_ADV_H
 #define CONFIGURATION_ADV_H_VERSION 020000

 // @section temperature
@ -1831,5 +1830,3 @@

 // Enable Marlin dev mode which adds some special commands
 //#define MARLIN_DEV_MODE
-
-#endif // CONFIGURATION_ADV_H
--- a/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration.h
+++ b/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration.h
@ -35,8 +36,6 @@
 * Advanced settings can be found in Configuration_adv.h
 *
 */
-#ifndef CONFIGURATION_H
-#define CONFIGURATION_H
 #define CONFIGURATION_H_VERSION 020000

 //===========================================================================
@ -2051,5 +2050,3 @@

 // Allow servo angle to be edited and saved to EEPROM
 //#define EDITABLE_SERVO_ANGLES
-
-#endif // CONFIGURATION_H
--- a/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration_adv.h
+++ b/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration_adv.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration_adv.h
@ -30,8 +31,6 @@
 * Basic settings can be found in Configuration.h
 *
 */
-#ifndef CONFIGURATION_ADV_H
-#define CONFIGURATION_ADV_H
 #define CONFIGURATION_ADV_H_VERSION 020000

 // @section temperature
@ -1830,5 +1829,3 @@

 // Enable Marlin dev mode which adds some special commands
 //#define MARLIN_DEV_MODE
-
-#endif // CONFIGURATION_ADV_H
--- a/Marlin/src/config/examples/AliExpress/CL-260/Configuration.h
+++ b/Marlin/src/config/examples/AliExpress/CL-260/Configuration.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration.h
@ -35,8 +36,6 @@
 * Advanced settings can be found in Configuration_adv.h
 *
 */
-#ifndef CONFIGURATION_H
-#define CONFIGURATION_H
 #define CONFIGURATION_H_VERSION 020000

 //===========================================================================
@ -2031,5 +2030,3 @@

 // Allow servo angle to be edited and saved to EEPROM
 //#define EDITABLE_SERVO_ANGLES
-
-#endif // CONFIGURATION_H
--- a/Marlin/src/config/examples/Anet/A2/Configuration.h
+++ b/Marlin/src/config/examples/Anet/A2/Configuration.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration.h
@ -35,8 +36,6 @@
 * Advanced settings can be found in Configuration_adv.h
 *
 */
-#ifndef CONFIGURATION_H
-#define CONFIGURATION_H
 #define CONFIGURATION_H_VERSION 020000

 //===========================================================================
@ -2033,5 +2032,3 @@

 // Allow servo angle to be edited and saved to EEPROM
 //#define EDITABLE_SERVO_ANGLES
-
-#endif // CONFIGURATION_H
--- a/Marlin/src/config/examples/Anet/A2/Configuration_adv.h
+++ b/Marlin/src/config/examples/Anet/A2/Configuration_adv.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration_adv.h
@ -30,8 +31,6 @@
 * Basic settings can be found in Configuration.h
 *
 */
-#ifndef CONFIGURATION_ADV_H
-#define CONFIGURATION_ADV_H
 #define CONFIGURATION_ADV_H_VERSION 020000

 // @section temperature
@ -1830,5 +1829,3 @@

 // Enable Marlin dev mode which adds some special commands
 //#define MARLIN_DEV_MODE
-
-#endif // CONFIGURATION_ADV_H
--- a/Marlin/src/config/examples/Anet/A2plus/Configuration.h
+++ b/Marlin/src/config/examples/Anet/A2plus/Configuration.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration.h
@ -35,8 +36,6 @@
 * Advanced settings can be found in Configuration_adv.h
 *
 */
-#ifndef CONFIGURATION_H
-#define CONFIGURATION_H
 #define CONFIGURATION_H_VERSION 020000

 //===========================================================================
@ -2033,5 +2032,3 @@

 // Allow servo angle to be edited and saved to EEPROM
 //#define EDITABLE_SERVO_ANGLES
-
-#endif // CONFIGURATION_H
--- a/Marlin/src/config/examples/Anet/A2plus/Configuration_adv.h
+++ b/Marlin/src/config/examples/Anet/A2plus/Configuration_adv.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration_adv.h
@ -30,8 +31,6 @@
 * Basic settings can be found in Configuration.h
 *
 */
-#ifndef CONFIGURATION_ADV_H
-#define CONFIGURATION_ADV_H
 #define CONFIGURATION_ADV_H_VERSION 020000

 // @section temperature
@ -1830,5 +1829,3 @@

 // Enable Marlin dev mode which adds some special commands
 //#define MARLIN_DEV_MODE
-
-#endif // CONFIGURATION_ADV_H
--- a/Marlin/src/config/examples/Anet/A6/Configuration.h
+++ b/Marlin/src/config/examples/Anet/A6/Configuration.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration.h
@ -35,8 +36,6 @@
 * Advanced settings can be found in Configuration_adv.h
 *
 */
-#ifndef CONFIGURATION_H
-#define CONFIGURATION_H
 #define CONFIGURATION_H_VERSION 020000

 //===========================================================================
@ -2186,5 +2185,3 @@

 // Allow servo angle to be edited and saved to EEPROM
 //#define EDITABLE_SERVO_ANGLES
-
-#endif // CONFIGURATION_H
--- a/Marlin/src/config/examples/Anet/A6/Configuration_adv.h
+++ b/Marlin/src/config/examples/Anet/A6/Configuration_adv.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration_adv.h
@ -30,8 +31,6 @@
 * Basic settings can be found in Configuration.h
 *
 */
-#ifndef CONFIGURATION_ADV_H
-#define CONFIGURATION_ADV_H
 #define CONFIGURATION_ADV_H_VERSION 020000

 // @section temperature
@ -1829,5 +1828,3 @@

 // Enable Marlin dev mode which adds some special commands
 //#define MARLIN_DEV_MODE
-
-#endif // CONFIGURATION_ADV_H
--- a/Marlin/src/config/examples/Anet/A8/Configuration.h
+++ b/Marlin/src/config/examples/Anet/A8/Configuration.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration.h
@ -35,8 +36,6 @@
 * Advanced settings can be found in Configuration_adv.h
 *
 */
-#ifndef CONFIGURATION_H
-#define CONFIGURATION_H
 #define CONFIGURATION_H_VERSION 020000

 //===========================================================================
@ -2040,5 +2039,3 @@

 // Allow servo angle to be edited and saved to EEPROM
 //#define EDITABLE_SERVO_ANGLES
-
-#endif // CONFIGURATION_H
--- a/Marlin/src/config/examples/Anet/A8/Configuration_adv.h
+++ b/Marlin/src/config/examples/Anet/A8/Configuration_adv.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration_adv.h
@ -30,8 +31,6 @@
 * Basic settings can be found in Configuration.h
 *
 */
-#ifndef CONFIGURATION_ADV_H
-#define CONFIGURATION_ADV_H
 #define CONFIGURATION_ADV_H_VERSION 020000

 // @section temperature
@ -1830,5 +1829,3 @@

 // Enable Marlin dev mode which adds some special commands
 //#define MARLIN_DEV_MODE
-
-#endif // CONFIGURATION_ADV_H
--- a/Marlin/src/config/examples/ArmEd/Configuration.h
+++ b/Marlin/src/config/examples/ArmEd/Configuration.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration.h
@ -35,8 +36,6 @@
 * Advanced settings can be found in Configuration_adv.h
 *
 */
-#ifndef CONFIGURATION_H
-#define CONFIGURATION_H
 #define CONFIGURATION_H_VERSION 020000

 //===========================================================================
@ -2032,5 +2031,3 @@

 // Allow servo angle to be edited and saved to EEPROM
 //#define EDITABLE_SERVO_ANGLES
-
-#endif // CONFIGURATION_H
--- a/Marlin/src/config/examples/ArmEd/Configuration_adv.h
+++ b/Marlin/src/config/examples/ArmEd/Configuration_adv.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration_adv.h
@ -30,8 +31,6 @@
 * Basic settings can be found in Configuration.h
 *
 */
-#ifndef CONFIGURATION_ADV_H
-#define CONFIGURATION_ADV_H
 #define CONFIGURATION_ADV_H_VERSION 020000

 // @section temperature
@ -1807,5 +1806,3 @@

 // Enable Marlin dev mode which adds some special commands
 //#define MARLIN_DEV_MODE
-
-#endif // CONFIGURATION_ADV_H
--- a/Marlin/src/config/examples/Azteeg/X5GT/Configuration.h
+++ b/Marlin/src/config/examples/Azteeg/X5GT/Configuration.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration.h
@ -35,8 +36,6 @@
 * Advanced settings can be found in Configuration_adv.h
 *
 */
-#ifndef CONFIGURATION_H
-#define CONFIGURATION_H
 #define CONFIGURATION_H_VERSION 020000

 //===========================================================================
@ -2031,5 +2030,3 @@

 // Allow servo angle to be edited and saved to EEPROM
 //#define EDITABLE_SERVO_ANGLES
-
-#endif // CONFIGURATION_H
--- a/Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration.h
+++ b/Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration.h
@ -35,8 +36,6 @@
 * Advanced settings can be found in Configuration_adv.h
 *
 */
-#ifndef CONFIGURATION_H
-#define CONFIGURATION_H
 #define CONFIGURATION_H_VERSION 020000

 //===========================================================================
@ -2031,5 +2030,3 @@

 // Allow servo angle to be edited and saved to EEPROM
 //#define EDITABLE_SERVO_ANGLES
-
-#endif // CONFIGURATION_H
--- a/Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h
+++ b/Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration_adv.h
@ -30,8 +31,6 @@
 * Basic settings can be found in Configuration.h
 *
 */
-#ifndef CONFIGURATION_ADV_H
-#define CONFIGURATION_ADV_H
 #define CONFIGURATION_ADV_H_VERSION 020000

 // @section temperature
@ -1829,5 +1828,3 @@

 // Enable Marlin dev mode which adds some special commands
 //#define MARLIN_DEV_MODE
-
-#endif // CONFIGURATION_ADV_H
--- a/Marlin/src/config/examples/BIBO/TouchX/default/Configuration.h
+++ b/Marlin/src/config/examples/BIBO/TouchX/default/Configuration.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration.h
@ -35,8 +36,6 @@
 * Advanced settings can be found in Configuration_adv.h
 *
 */
-#ifndef CONFIGURATION_H
-#define CONFIGURATION_H
 #define CONFIGURATION_H_VERSION 020000

 //===========================================================================
@ -2031,5 +2030,3 @@

 // Allow servo angle to be edited and saved to EEPROM
 //#define EDITABLE_SERVO_ANGLES
-
-#endif // CONFIGURATION_H
--- a/Marlin/src/config/examples/BIBO/TouchX/default/Configuration_adv.h
+++ b/Marlin/src/config/examples/BIBO/TouchX/default/Configuration_adv.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration_adv.h
@ -30,8 +31,6 @@
 * Basic settings can be found in Configuration.h
 *
 */
-#ifndef CONFIGURATION_ADV_H
-#define CONFIGURATION_ADV_H
 #define CONFIGURATION_ADV_H_VERSION 020000

 // @section temperature
@ -1830,5 +1829,3 @@

 // Enable Marlin dev mode which adds some special commands
 //#define MARLIN_DEV_MODE
-
-#endif // CONFIGURATION_ADV_H
--- a/Marlin/src/config/examples/BQ/Hephestos/Configuration.h
+++ b/Marlin/src/config/examples/BQ/Hephestos/Configuration.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration.h
@ -35,8 +36,6 @@
 * Advanced settings can be found in Configuration_adv.h
 *
 */
-#ifndef CONFIGURATION_H
-#define CONFIGURATION_H
 #define CONFIGURATION_H_VERSION 020000

 //===========================================================================
@ -2019,5 +2018,3 @@

 // Allow servo angle to be edited and saved to EEPROM
 //#define EDITABLE_SERVO_ANGLES
-
-#endif // CONFIGURATION_H
--- a/Marlin/src/config/examples/BQ/Hephestos/Configuration_adv.h
+++ b/Marlin/src/config/examples/BQ/Hephestos/Configuration_adv.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration_adv.h
@ -30,8 +31,6 @@
 * Basic settings can be found in Configuration.h
 *
 */
-#ifndef CONFIGURATION_ADV_H
-#define CONFIGURATION_ADV_H
 #define CONFIGURATION_ADV_H_VERSION 020000

 // @section temperature
@ -1830,5 +1829,3 @@

 // Enable Marlin dev mode which adds some special commands
 //#define MARLIN_DEV_MODE
-
-#endif // CONFIGURATION_ADV_H
--- a/Marlin/src/config/examples/BQ/Hephestos_2/Configuration.h
+++ b/Marlin/src/config/examples/BQ/Hephestos_2/Configuration.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration.h
@ -35,8 +36,6 @@
 * Advanced settings can be found in Configuration_adv.h
 *
 */
-#ifndef CONFIGURATION_H
-#define CONFIGURATION_H
 #define CONFIGURATION_H_VERSION 020000

 //===========================================================================
@ -2031,5 +2030,3 @@

 // Allow servo angle to be edited and saved to EEPROM
 //#define EDITABLE_SERVO_ANGLES
-
-#endif // CONFIGURATION_H
--- a/Marlin/src/config/examples/BQ/Hephestos_2/Configuration_adv.h
+++ b/Marlin/src/config/examples/BQ/Hephestos_2/Configuration_adv.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration_adv.h
@ -30,8 +31,6 @@
 * Basic settings can be found in Configuration.h
 *
 */
-#ifndef CONFIGURATION_ADV_H
-#define CONFIGURATION_ADV_H
 #define CONFIGURATION_ADV_H_VERSION 020000

 // @section temperature
@ -1837,5 +1836,3 @@

 // Enable Marlin dev mode which adds some special commands
 //#define MARLIN_DEV_MODE
-
-#endif // CONFIGURATION_ADV_H
--- a/Marlin/src/config/examples/BQ/WITBOX/Configuration.h
+++ b/Marlin/src/config/examples/BQ/WITBOX/Configuration.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration.h
@ -35,8 +36,6 @@
 * Advanced settings can be found in Configuration_adv.h
 *
 */
-#ifndef CONFIGURATION_H
-#define CONFIGURATION_H
 #define CONFIGURATION_H_VERSION 020000

 //===========================================================================
@ -2019,5 +2018,3 @@

 // Allow servo angle to be edited and saved to EEPROM
 //#define EDITABLE_SERVO_ANGLES
-
-#endif // CONFIGURATION_H
--- a/Marlin/src/config/examples/BQ/WITBOX/Configuration_adv.h
+++ b/Marlin/src/config/examples/BQ/WITBOX/Configuration_adv.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration_adv.h
@ -30,8 +31,6 @@
 * Basic settings can be found in Configuration.h
 *
 */
-#ifndef CONFIGURATION_ADV_H
-#define CONFIGURATION_ADV_H
 #define CONFIGURATION_ADV_H_VERSION 020000

 // @section temperature
@ -1830,5 +1829,3 @@

 // Enable Marlin dev mode which adds some special commands
 //#define MARLIN_DEV_MODE
-
-#endif // CONFIGURATION_ADV_H
--- a/Marlin/src/config/examples/Cartesio/Configuration.h
+++ b/Marlin/src/config/examples/Cartesio/Configuration.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration.h
@ -35,8 +36,6 @@
 * Advanced settings can be found in Configuration_adv.h
 *
 */
-#ifndef CONFIGURATION_H
-#define CONFIGURATION_H
 #define CONFIGURATION_H_VERSION 020000

 //===========================================================================
@ -2030,5 +2029,3 @@

 // Allow servo angle to be edited and saved to EEPROM
 //#define EDITABLE_SERVO_ANGLES
-
-#endif // CONFIGURATION_H
--- a/Marlin/src/config/examples/Cartesio/Configuration_adv.h
+++ b/Marlin/src/config/examples/Cartesio/Configuration_adv.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration_adv.h
@ -30,8 +31,6 @@
 * Basic settings can be found in Configuration.h
 *
 */
-#ifndef CONFIGURATION_ADV_H
-#define CONFIGURATION_ADV_H
 #define CONFIGURATION_ADV_H_VERSION 020000

 // @section temperature
@ -1830,5 +1829,3 @@

 // Enable Marlin dev mode which adds some special commands
 //#define MARLIN_DEV_MODE
-
-#endif // CONFIGURATION_ADV_H
--- a/Marlin/src/config/examples/Creality/CR-10/Configuration.h
+++ b/Marlin/src/config/examples/Creality/CR-10/Configuration.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration.h
@ -35,8 +36,6 @@
 * Advanced settings can be found in Configuration_adv.h
 *
 */
-#ifndef CONFIGURATION_H
-#define CONFIGURATION_H
 #define CONFIGURATION_H_VERSION 020000

 //===========================================================================
@ -2041,5 +2040,3 @@

 // Allow servo angle to be edited and saved to EEPROM
 //#define EDITABLE_SERVO_ANGLES
-
-#endif // CONFIGURATION_H
--- a/Marlin/src/config/examples/Creality/CR-10/Configuration_adv.h
+++ b/Marlin/src/config/examples/Creality/CR-10/Configuration_adv.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration_adv.h
@ -30,8 +31,6 @@
 * Basic settings can be found in Configuration.h
 *
 */
-#ifndef CONFIGURATION_ADV_H
-#define CONFIGURATION_ADV_H
 #define CONFIGURATION_ADV_H_VERSION 020000

 // @section temperature
@ -1833,5 +1832,3 @@

 // Enable Marlin dev mode which adds some special commands
 //#define MARLIN_DEV_MODE
-
-#endif // CONFIGURATION_ADV_H
--- a/Marlin/src/config/examples/Creality/CR-10S/Configuration.h
+++ b/Marlin/src/config/examples/Creality/CR-10S/Configuration.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration.h
@ -35,8 +36,6 @@
 * Advanced settings can be found in Configuration_adv.h
 *
 */
-#ifndef CONFIGURATION_H
-#define CONFIGURATION_H
 #define CONFIGURATION_H_VERSION 020000

 //===========================================================================
@ -2032,5 +2031,3 @@

 // Allow servo angle to be edited and saved to EEPROM
 //#define EDITABLE_SERVO_ANGLES
-
-#endif // CONFIGURATION_H
--- a/Marlin/src/config/examples/Creality/CR-10S/Configuration_adv.h
+++ b/Marlin/src/config/examples/Creality/CR-10S/Configuration_adv.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration_adv.h
@ -30,8 +31,6 @@
 * Basic settings can be found in Configuration.h
 *
 */
-#ifndef CONFIGURATION_ADV_H
-#define CONFIGURATION_ADV_H
 #define CONFIGURATION_ADV_H_VERSION 020000

 // @section temperature
@ -1830,5 +1829,3 @@

 // Enable Marlin dev mode which adds some special commands
 //#define MARLIN_DEV_MODE
-
-#endif // CONFIGURATION_ADV_H
--- a/Marlin/src/config/examples/Creality/CR-10mini/Configuration.h
+++ b/Marlin/src/config/examples/Creality/CR-10mini/Configuration.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration.h
@ -44,8 +45,6 @@
 * CR10_STOCKDISPLAY (RAMPS-compatible with single 10-pin plug)
 */

-#ifndef CONFIGURATION_H
-#define CONFIGURATION_H
 #define CONFIGURATION_H_VERSION 020000

 //===========================================================================
@ -2050,5 +2049,3 @@

 // Allow servo angle to be edited and saved to EEPROM
 //#define EDITABLE_SERVO_ANGLES
-
-#endif // CONFIGURATION_H
--- a/Marlin/src/config/examples/Creality/CR-10mini/Configuration_adv.h
+++ b/Marlin/src/config/examples/Creality/CR-10mini/Configuration_adv.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration_adv.h
@ -30,8 +31,6 @@
 * Basic settings can be found in Configuration.h
 *
 */
-#ifndef CONFIGURATION_ADV_H
-#define CONFIGURATION_ADV_H
 #define CONFIGURATION_ADV_H_VERSION 020000

 // @section temperature
@ -1830,5 +1829,3 @@

 // Enable Marlin dev mode which adds some special commands
 //#define MARLIN_DEV_MODE
-
-#endif // CONFIGURATION_ADV_H
--- a/Marlin/src/config/examples/Creality/CR-8/Configuration.h
+++ b/Marlin/src/config/examples/Creality/CR-8/Configuration.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration.h
@ -35,8 +36,6 @@
 * Advanced settings can be found in Configuration_adv.h
 *
 */
-#ifndef CONFIGURATION_H
-#define CONFIGURATION_H
 #define CONFIGURATION_H_VERSION 020000

 //===========================================================================
@ -2041,5 +2040,3 @@

 // Allow servo angle to be edited and saved to EEPROM
 //#define EDITABLE_SERVO_ANGLES
-
-#endif // CONFIGURATION_H
--- a/Marlin/src/config/examples/Creality/CR-8/Configuration_adv.h
+++ b/Marlin/src/config/examples/Creality/CR-8/Configuration_adv.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration_adv.h
@ -30,8 +31,6 @@
 * Basic settings can be found in Configuration.h
 *
 */
-#ifndef CONFIGURATION_ADV_H
-#define CONFIGURATION_ADV_H
 #define CONFIGURATION_ADV_H_VERSION 020000

 // @section temperature
@ -1830,5 +1829,3 @@

 // Enable Marlin dev mode which adds some special commands
 //#define MARLIN_DEV_MODE
-
-#endif // CONFIGURATION_ADV_H
--- a/Marlin/src/config/examples/Creality/Ender-2/Configuration.h
+++ b/Marlin/src/config/examples/Creality/Ender-2/Configuration.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration.h
@ -35,8 +36,6 @@
 * Advanced settings can be found in Configuration_adv.h
 *
 */
-#ifndef CONFIGURATION_H
-#define CONFIGURATION_H
 #define CONFIGURATION_H_VERSION 020000

 //===========================================================================
@ -2035,5 +2034,3 @@

 // Allow servo angle to be edited and saved to EEPROM
 //#define EDITABLE_SERVO_ANGLES
-
-#endif // CONFIGURATION_H
--- a/Marlin/src/config/examples/Creality/Ender-2/Configuration_adv.h
+++ b/Marlin/src/config/examples/Creality/Ender-2/Configuration_adv.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration_adv.h
@ -30,8 +31,6 @@
 * Basic settings can be found in Configuration.h
 *
 */
-#ifndef CONFIGURATION_ADV_H
-#define CONFIGURATION_ADV_H
 #define CONFIGURATION_ADV_H_VERSION 020000

 // @section temperature
@ -1830,5 +1829,3 @@

 // Enable Marlin dev mode which adds some special commands
 //#define MARLIN_DEV_MODE
-
-#endif // CONFIGURATION_ADV_H
--- a/Marlin/src/config/examples/Creality/Ender-3/Configuration.h
+++ b/Marlin/src/config/examples/Creality/Ender-3/Configuration.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration.h
@ -35,8 +36,6 @@
 * Advanced settings can be found in Configuration_adv.h
 *
 */
-#ifndef CONFIGURATION_H
-#define CONFIGURATION_H
 #define CONFIGURATION_H_VERSION 020000

 //===========================================================================
@ -2035,5 +2034,3 @@

 // Allow servo angle to be edited and saved to EEPROM
 //#define EDITABLE_SERVO_ANGLES
-
-#endif // CONFIGURATION_H
--- a/Marlin/src/config/examples/Creality/Ender-3/Configuration_adv.h
+++ b/Marlin/src/config/examples/Creality/Ender-3/Configuration_adv.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration_adv.h
@ -30,8 +31,6 @@
 * Basic settings can be found in Configuration.h
 *
 */
-#ifndef CONFIGURATION_ADV_H
-#define CONFIGURATION_ADV_H
 #define CONFIGURATION_ADV_H_VERSION 020000

 // @section temperature
@ -1830,5 +1829,3 @@

 // Enable Marlin dev mode which adds some special commands
 //#define MARLIN_DEV_MODE
-
-#endif // CONFIGURATION_ADV_H
--- a/Marlin/src/config/examples/Creality/Ender-4/Configuration.h
+++ b/Marlin/src/config/examples/Creality/Ender-4/Configuration.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration.h
@ -35,8 +36,6 @@
 * Advanced settings can be found in Configuration_adv.h
 *
 */
-#ifndef CONFIGURATION_H
-#define CONFIGURATION_H
 #define CONFIGURATION_H_VERSION 020000

 //===========================================================================
@ -2041,5 +2040,3 @@

 // Allow servo angle to be edited and saved to EEPROM
 //#define EDITABLE_SERVO_ANGLES
-
-#endif // CONFIGURATION_H
--- a/Marlin/src/config/examples/Creality/Ender-4/Configuration_adv.h
+++ b/Marlin/src/config/examples/Creality/Ender-4/Configuration_adv.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration_adv.h
@ -30,8 +31,6 @@
 * Basic settings can be found in Configuration.h
 *
 */
-#ifndef CONFIGURATION_ADV_H
-#define CONFIGURATION_ADV_H
 #define CONFIGURATION_ADV_H_VERSION 020000

 // @section temperature
@ -1830,5 +1829,3 @@

 // Enable Marlin dev mode which adds some special commands
 //#define MARLIN_DEV_MODE
-
-#endif // CONFIGURATION_ADV_H
--- a/Marlin/src/config/examples/Einstart-S/Configuration.h
+++ b/Marlin/src/config/examples/Einstart-S/Configuration.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration.h
@ -35,8 +36,6 @@
 * Advanced settings can be found in Configuration_adv.h
 *
 */
-#ifndef CONFIGURATION_H
-#define CONFIGURATION_H
 #define CONFIGURATION_H_VERSION 020000

 //===========================================================================
@ -2037,5 +2036,3 @@

 // Allow servo angle to be edited and saved to EEPROM
 //#define EDITABLE_SERVO_ANGLES
-
-#endif // CONFIGURATION_H
--- a/Marlin/src/config/examples/Einstart-S/Configuration_adv.h
+++ b/Marlin/src/config/examples/Einstart-S/Configuration_adv.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration_adv.h
@ -30,8 +31,6 @@
 * Basic settings can be found in Configuration.h
 *
 */
-#ifndef CONFIGURATION_ADV_H
-#define CONFIGURATION_ADV_H
 #define CONFIGURATION_ADV_H_VERSION 020000

 // @section temperature
@ -1830,5 +1829,3 @@

 // Enable Marlin dev mode which adds some special commands
 //#define MARLIN_DEV_MODE
-
-#endif // CONFIGURATION_ADV_H
--- a/Marlin/src/config/examples/Felix/Configuration.h
+++ b/Marlin/src/config/examples/Felix/Configuration.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration.h
@ -35,8 +36,6 @@
 * Advanced settings can be found in Configuration_adv.h
 *
 */
-#ifndef CONFIGURATION_H
-#define CONFIGURATION_H
 #define CONFIGURATION_H_VERSION 020000

 //===========================================================================
@ -2013,5 +2012,3 @@

 // Allow servo angle to be edited and saved to EEPROM
 //#define EDITABLE_SERVO_ANGLES
-
-#endif // CONFIGURATION_H
--- a/Marlin/src/config/examples/Felix/Configuration_adv.h
+++ b/Marlin/src/config/examples/Felix/Configuration_adv.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration_adv.h
@ -30,8 +31,6 @@
 * Basic settings can be found in Configuration.h
 *
 */
-#ifndef CONFIGURATION_ADV_H
-#define CONFIGURATION_ADV_H
 #define CONFIGURATION_ADV_H_VERSION 020000

 // @section temperature
@ -1830,5 +1829,3 @@

 // Enable Marlin dev mode which adds some special commands
 //#define MARLIN_DEV_MODE
-
-#endif // CONFIGURATION_ADV_H
--- a/Marlin/src/config/examples/Felix/DUAL/Configuration.h
+++ b/Marlin/src/config/examples/Felix/DUAL/Configuration.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration.h
@ -35,8 +36,6 @@
 * Advanced settings can be found in Configuration_adv.h
 *
 */
-#ifndef CONFIGURATION_H
-#define CONFIGURATION_H
 #define CONFIGURATION_H_VERSION 020000

 //===========================================================================
@ -2013,5 +2012,3 @@

 // Allow servo angle to be edited and saved to EEPROM
 //#define EDITABLE_SERVO_ANGLES
-
-#endif // CONFIGURATION_H
--- a/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration.h
+++ b/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration.h
@ -35,8 +36,6 @@
 * Advanced settings can be found in Configuration_adv.h
 *
 */
-#ifndef CONFIGURATION_H
-#define CONFIGURATION_H
 #define CONFIGURATION_H_VERSION 020000

 //===========================================================================
@ -2037,5 +2036,3 @@

 // Allow servo angle to be edited and saved to EEPROM
 //#define EDITABLE_SERVO_ANGLES
-
-#endif // CONFIGURATION_H
--- a/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration_adv.h
+++ b/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration_adv.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration_adv.h
@ -30,8 +31,6 @@
 * Basic settings can be found in Configuration.h
 *
 */
-#ifndef CONFIGURATION_ADV_H
-#define CONFIGURATION_ADV_H
 #define CONFIGURATION_ADV_H_VERSION 020000

 // @section temperature
@ -1838,5 +1837,3 @@

 // Enable Marlin dev mode which adds some special commands
 //#define MARLIN_DEV_MODE
-
-#endif // CONFIGURATION_ADV_H
--- a/Marlin/src/config/examples/Formbot/Raptor/Configuration.h
+++ b/Marlin/src/config/examples/Formbot/Raptor/Configuration.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration.h
@ -35,8 +36,6 @@
 * Advanced settings can be found in Configuration_adv.h
 *
 */
-#ifndef CONFIGURATION_H
-#define CONFIGURATION_H
 #define CONFIGURATION_H_VERSION 020000

 //===========================================================================
@ -2137,5 +2136,3 @@

 // Allow servo angle to be edited and saved to EEPROM
 //#define EDITABLE_SERVO_ANGLES
-
-#endif // CONFIGURATION_H
--- a/Marlin/src/config/examples/Formbot/Raptor/Configuration_adv.h
+++ b/Marlin/src/config/examples/Formbot/Raptor/Configuration_adv.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration_adv.h
@ -30,8 +31,6 @@
 * Basic settings can be found in Configuration.h
 *
 */
-#ifndef CONFIGURATION_ADV_H
-#define CONFIGURATION_ADV_H
 #define CONFIGURATION_ADV_H_VERSION 020000

 // @section temperature
@ -1834,5 +1833,3 @@

 // Enable Marlin dev mode which adds some special commands
 //#define MARLIN_DEV_MODE
-
-#endif // CONFIGURATION_ADV_H
--- a/Marlin/src/config/examples/Formbot/T_Rex_2+/Configuration.h
+++ b/Marlin/src/config/examples/Formbot/T_Rex_2+/Configuration.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 //#define ROXYs_TRex         // Turn this on to get customizations only available on Roxy's T-Rex 2+
                             // Marlin controlled heat bed, Max7219 debug LED's, less bright LED light level
@ -38,8 +39,6 @@
 * Advanced settings can be found in Configuration_adv.h
 *
 */
-#ifndef CONFIGURATION_H
-#define CONFIGURATION_H
 #define CONFIGURATION_H_VERSION 020000

 //===========================================================================
@ -2078,5 +2077,3 @@

 // Allow servo angle to be edited and saved to EEPROM
 //#define EDITABLE_SERVO_ANGLES
-
-#endif // CONFIGURATION_H
--- a/Marlin/src/config/examples/Formbot/T_Rex_2+/Configuration_adv.h
+++ b/Marlin/src/config/examples/Formbot/T_Rex_2+/Configuration_adv.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration_adv.h
@ -30,8 +31,6 @@
 * Basic settings can be found in Configuration.h
 *
 */
-#ifndef CONFIGURATION_ADV_H
-#define CONFIGURATION_ADV_H
 #define CONFIGURATION_ADV_H_VERSION 020000

 // @section temperature
@ -1840,5 +1839,3 @@

 // Enable Marlin dev mode which adds some special commands
 //#define MARLIN_DEV_MODE
-
-#endif // CONFIGURATION_ADV_H
--- a/Marlin/src/config/examples/Formbot/T_Rex_3/Configuration.h
+++ b/Marlin/src/config/examples/Formbot/T_Rex_3/Configuration.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration.h
@ -35,8 +36,6 @@
 * Advanced settings can be found in Configuration_adv.h
 *
 */
-#ifndef CONFIGURATION_H
-#define CONFIGURATION_H
 #define CONFIGURATION_H_VERSION 020000

 //===========================================================================
@ -2064,5 +2063,3 @@

 // Allow servo angle to be edited and saved to EEPROM
 //#define EDITABLE_SERVO_ANGLES
-
-#endif // CONFIGURATION_H
--- a/Marlin/src/config/examples/Formbot/T_Rex_3/Configuration_adv.h
+++ b/Marlin/src/config/examples/Formbot/T_Rex_3/Configuration_adv.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration_adv.h
@ -30,8 +31,6 @@
 * Basic settings can be found in Configuration.h
 *
 */
-#ifndef CONFIGURATION_ADV_H
-#define CONFIGURATION_ADV_H
 #define CONFIGURATION_ADV_H_VERSION 020000

 // @section temperature
@ -1840,5 +1839,3 @@

 // Enable Marlin dev mode which adds some special commands
 //#define MARLIN_DEV_MODE
-
-#endif // CONFIGURATION_ADV_H
--- a/Marlin/src/config/examples/Geeetech/GT2560/Configuration.h
+++ b/Marlin/src/config/examples/Geeetech/GT2560/Configuration.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration.h
@ -35,8 +36,6 @@
 * Advanced settings can be found in Configuration_adv.h
 *
 */
-#ifndef CONFIGURATION_H
-#define CONFIGURATION_H
 #define CONFIGURATION_H_VERSION 020000

 //===========================================================================
@ -2055,5 +2054,3 @@

 // Allow servo angle to be edited and saved to EEPROM
 //#define EDITABLE_SERVO_ANGLES
-
-#endif // CONFIGURATION_H
--- a/Marlin/src/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h
+++ b/Marlin/src/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration.h
@ -35,8 +36,6 @@
 * Advanced settings can be found in Configuration_adv.h
 *
 */
-#ifndef CONFIGURATION_H
-#define CONFIGURATION_H
 #define CONFIGURATION_H_VERSION 020000

 //===========================================================================
@ -2031,5 +2030,3 @@

 // Allow servo angle to be edited and saved to EEPROM
 //#define EDITABLE_SERVO_ANGLES
-
-#endif // CONFIGURATION_H
--- a/Marlin/src/config/examples/Geeetech/MeCreator2/Configuration.h
+++ b/Marlin/src/config/examples/Geeetech/MeCreator2/Configuration.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration.h
@ -35,8 +36,6 @@
 * Advanced settings can be found in Configuration_adv.h
 *
 */
-#ifndef CONFIGURATION_H
-#define CONFIGURATION_H
 #define CONFIGURATION_H_VERSION 020000

 //===========================================================================
@ -2038,5 +2037,3 @@

 // Allow servo angle to be edited and saved to EEPROM
 //#define EDITABLE_SERVO_ANGLES
-
-#endif // CONFIGURATION_H
--- a/Marlin/src/config/examples/Geeetech/MeCreator2/Configuration_adv.h
+++ b/Marlin/src/config/examples/Geeetech/MeCreator2/Configuration_adv.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration_adv.h
@ -30,8 +31,6 @@
 * Basic settings can be found in Configuration.h
 *
 */
-#ifndef CONFIGURATION_ADV_H
-#define CONFIGURATION_ADV_H
 #define CONFIGURATION_ADV_H_VERSION 020000

 // @section temperature
@ -1816,5 +1815,3 @@

 // Enable Marlin dev mode which adds some special commands
 //#define MARLIN_DEV_MODE
-
-#endif // CONFIGURATION_ADV_H
--- a/Marlin/src/config/examples/Geeetech/Prusa
+++ b/Marlin/src/config/examples/Geeetech/Prusa
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration.h
@ -35,8 +36,6 @@
 * Advanced settings can be found in Configuration_adv.h
 *
 */
-#ifndef CONFIGURATION_H
-#define CONFIGURATION_H
 #define CONFIGURATION_H_VERSION 020000

 //===========================================================================
@ -2047,5 +2046,3 @@

 // Allow servo angle to be edited and saved to EEPROM
 //#define EDITABLE_SERVO_ANGLES
-
-#endif // CONFIGURATION_H
--- a/Marlin/src/config/examples/Geeetech/Prusa
+++ b/Marlin/src/config/examples/Geeetech/Prusa
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration.h
@ -35,8 +36,6 @@
 * Advanced settings can be found in Configuration_adv.h
 *
 */
-#ifndef CONFIGURATION_H
-#define CONFIGURATION_H
 #define CONFIGURATION_H_VERSION 020000

 //===========================================================================
@ -2046,5 +2045,3 @@

 // Allow servo angle to be edited and saved to EEPROM
 //#define EDITABLE_SERVO_ANGLES
-
-#endif // CONFIGURATION_H
--- a/Marlin/src/config/examples/Geeetech/Prusa
+++ b/Marlin/src/config/examples/Geeetech/Prusa
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration.h
@ -35,8 +36,6 @@
 * Advanced settings can be found in Configuration_adv.h
 *
 */
-#ifndef CONFIGURATION_H
-#define CONFIGURATION_H
 #define CONFIGURATION_H_VERSION 020000

 //===========================================================================
@ -2031,5 +2030,3 @@

 // Allow servo angle to be edited and saved to EEPROM
 //#define EDITABLE_SERVO_ANGLES
-
-#endif // CONFIGURATION_H
--- a/Marlin/src/config/examples/Geeetech/Prusa
+++ b/Marlin/src/config/examples/Geeetech/Prusa
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration_adv.h
@ -30,8 +31,6 @@
 * Basic settings can be found in Configuration.h
 *
 */
-#ifndef CONFIGURATION_ADV_H
-#define CONFIGURATION_ADV_H
 #define CONFIGURATION_ADV_H_VERSION 020000

 // @section temperature
@ -1830,5 +1829,3 @@

 // Enable Marlin dev mode which adds some special commands
 //#define MARLIN_DEV_MODE
-
-#endif // CONFIGURATION_ADV_H
--- a/Marlin/src/config/examples/Geeetech/Prusa
+++ b/Marlin/src/config/examples/Geeetech/Prusa
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration.h
@ -35,8 +36,6 @@
 * Advanced settings can be found in Configuration_adv.h
 *
 */
-#ifndef CONFIGURATION_H
-#define CONFIGURATION_H
 #define CONFIGURATION_H_VERSION 020000

 //===========================================================================
@ -2031,5 +2030,3 @@

 // Allow servo angle to be edited and saved to EEPROM
 //#define EDITABLE_SERVO_ANGLES
-
-#endif // CONFIGURATION_H
--- a/Marlin/src/config/examples/Geeetech/Prusa
+++ b/Marlin/src/config/examples/Geeetech/Prusa
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration_adv.h
@ -30,8 +31,6 @@
 * Basic settings can be found in Configuration.h
 *
 */
-#ifndef CONFIGURATION_ADV_H
-#define CONFIGURATION_ADV_H
 #define CONFIGURATION_ADV_H_VERSION 020000

 // @section temperature
@ -1830,5 +1829,3 @@

 // Enable Marlin dev mode which adds some special commands
 //#define MARLIN_DEV_MODE
-
-#endif // CONFIGURATION_ADV_H
--- a/Marlin/src/config/examples/Infitary/i3-M508/Configuration.h
+++ b/Marlin/src/config/examples/Infitary/i3-M508/Configuration.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration.h
@ -35,8 +36,6 @@
 * Advanced settings can be found in Configuration_adv.h
 *
 */
-#ifndef CONFIGURATION_H
-#define CONFIGURATION_H
 #define CONFIGURATION_H_VERSION 020000

 //===========================================================================
@ -2035,5 +2034,3 @@

 // Allow servo angle to be edited and saved to EEPROM
 //#define EDITABLE_SERVO_ANGLES
-
-#endif // CONFIGURATION_H
--- a/Marlin/src/config/examples/Infitary/i3-M508/Configuration_adv.h
+++ b/Marlin/src/config/examples/Infitary/i3-M508/Configuration_adv.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration_adv.h
@ -30,8 +31,6 @@
 * Basic settings can be found in Configuration.h
 *
 */
-#ifndef CONFIGURATION_ADV_H
-#define CONFIGURATION_ADV_H
 #define CONFIGURATION_ADV_H_VERSION 020000

 // @section temperature
@ -1830,5 +1829,3 @@

 // Enable Marlin dev mode which adds some special commands
 //#define MARLIN_DEV_MODE
-
-#endif // CONFIGURATION_ADV_H
--- a/Marlin/src/config/examples/JGAurora/A5/Configuration.h
+++ b/Marlin/src/config/examples/JGAurora/A5/Configuration.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * JGAurora A5 configuration
@ -40,8 +41,6 @@
 * Advanced settings can be found in Configuration_adv.h
 *
 */
-#ifndef CONFIGURATION_H
-#define CONFIGURATION_H
 #define CONFIGURATION_H_VERSION 020000

 //===========================================================================
@ -2042,5 +2041,3 @@

 // Allow servo angle to be edited and saved to EEPROM
 //#define EDITABLE_SERVO_ANGLES
-
-#endif // CONFIGURATION_H
--- a/Marlin/src/config/examples/JGAurora/A5/Configuration_adv.h
+++ b/Marlin/src/config/examples/JGAurora/A5/Configuration_adv.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration_adv.h
@ -30,8 +31,6 @@
 * Basic settings can be found in Configuration.h
 *
 */
-#ifndef CONFIGURATION_ADV_H
-#define CONFIGURATION_ADV_H
 #define CONFIGURATION_ADV_H_VERSION 020000

 // @section temperature
@ -1830,5 +1829,3 @@

 // Enable Marlin dev mode which adds some special commands
 //#define MARLIN_DEV_MODE
-
-#endif // CONFIGURATION_ADV_H
--- a/Marlin/src/config/examples/MakerParts/Configuration.h
+++ b/Marlin/src/config/examples/MakerParts/Configuration.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration.h
@ -35,8 +36,6 @@
 * Advanced settings can be found in Configuration_adv.h
 *
 */
-#ifndef CONFIGURATION_H
-#define CONFIGURATION_H
 #define CONFIGURATION_H_VERSION 020000

 //===========================================================================
@ -2051,5 +2050,3 @@

 // Allow servo angle to be edited and saved to EEPROM
 //#define EDITABLE_SERVO_ANGLES
-
-#endif // CONFIGURATION_H
--- a/Marlin/src/config/examples/MakerParts/Configuration_adv.h
+++ b/Marlin/src/config/examples/MakerParts/Configuration_adv.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration_adv.h
@ -30,8 +31,6 @@
 * Basic settings can be found in Configuration.h
 *
 */
-#ifndef CONFIGURATION_ADV_H
-#define CONFIGURATION_ADV_H
 #define CONFIGURATION_ADV_H_VERSION 020000

 // @section temperature
@ -1830,5 +1829,3 @@

 // Enable Marlin dev mode which adds some special commands
 //#define MARLIN_DEV_MODE
-
-#endif // CONFIGURATION_ADV_H
--- a/Marlin/src/config/examples/Malyan/M150/Configuration.h
+++ b/Marlin/src/config/examples/Malyan/M150/Configuration.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Maylan M150 Configuration
@ -40,8 +41,6 @@
 * Advanced settings can be found in Configuration_adv.h
 *
 */
-#ifndef CONFIGURATION_H
-#define CONFIGURATION_H
 #define CONFIGURATION_H_VERSION 020000

 //===========================================================================
@ -2059,5 +2058,3 @@

 // Allow servo angle to be edited and saved to EEPROM
 //#define EDITABLE_SERVO_ANGLES
-
-#endif // CONFIGURATION_H
--- a/Marlin/src/config/examples/Malyan/M150/Configuration_adv.h
+++ b/Marlin/src/config/examples/Malyan/M150/Configuration_adv.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration_adv.h
@ -30,8 +31,6 @@
 * Basic settings can be found in Configuration.h
 *
 */
-#ifndef CONFIGURATION_ADV_H
-#define CONFIGURATION_ADV_H
 #define CONFIGURATION_ADV_H_VERSION 020000

 // @section temperature
@ -1830,5 +1829,3 @@

 // Enable Marlin dev mode which adds some special commands
 //#define MARLIN_DEV_MODE
-
-#endif // CONFIGURATION_ADV_H
--- a/Marlin/src/config/examples/Malyan/M200/Configuration.h
+++ b/Marlin/src/config/examples/Malyan/M200/Configuration.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration.h
@ -35,8 +36,6 @@
 * Advanced settings can be found in Configuration_adv.h
 *
 */
-#ifndef CONFIGURATION_H
-#define CONFIGURATION_H
 #define CONFIGURATION_H_VERSION 020000

 //===========================================================================
@ -2030,5 +2029,3 @@

 // Allow servo angle to be edited and saved to EEPROM
 //#define EDITABLE_SERVO_ANGLES
-
-#endif // CONFIGURATION_H
--- a/Marlin/src/config/examples/Malyan/M200/Configuration_adv.h
+++ b/Marlin/src/config/examples/Malyan/M200/Configuration_adv.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration_adv.h
@ -30,8 +31,6 @@
 * Basic settings can be found in Configuration.h
 *
 */
-#ifndef CONFIGURATION_ADV_H
-#define CONFIGURATION_ADV_H
 #define CONFIGURATION_ADV_H_VERSION 020000

 // @section temperature
@ -1830,5 +1829,3 @@

 // Enable Marlin dev mode which adds some special commands
 //#define MARLIN_DEV_MODE
-
-#endif // CONFIGURATION_ADV_H
--- a/Marlin/src/config/examples/Micromake/C1/basic/Configuration.h
+++ b/Marlin/src/config/examples/Micromake/C1/basic/Configuration.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration.h
@ -35,8 +36,6 @@
 * Advanced settings can be found in Configuration_adv.h
 *
 */
-#ifndef CONFIGURATION_H
-#define CONFIGURATION_H
 #define CONFIGURATION_H_VERSION 020000

 //===========================================================================
@ -2035,5 +2034,3 @@

 // Allow servo angle to be edited and saved to EEPROM
 //#define EDITABLE_SERVO_ANGLES
-
-#endif // CONFIGURATION_H
--- a/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration.h
+++ b/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration.h
@ -35,8 +36,6 @@
 * Advanced settings can be found in Configuration_adv.h
 *
 */
-#ifndef CONFIGURATION_H
-#define CONFIGURATION_H
 #define CONFIGURATION_H_VERSION 020000

 //===========================================================================
@ -2035,5 +2034,3 @@

 // Allow servo angle to be edited and saved to EEPROM
 //#define EDITABLE_SERVO_ANGLES
-
-#endif // CONFIGURATION_H
--- a/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration_adv.h
+++ b/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration_adv.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration_adv.h
@ -30,8 +31,6 @@
 * Basic settings can be found in Configuration.h
 *
 */
-#ifndef CONFIGURATION_ADV_H
-#define CONFIGURATION_ADV_H
 #define CONFIGURATION_ADV_H_VERSION 020000

 // @section temperature
@ -1830,5 +1829,3 @@

 // Enable Marlin dev mode which adds some special commands
 //#define MARLIN_DEV_MODE
-
-#endif // CONFIGURATION_ADV_H
--- a/Marlin/src/config/examples/Mks/Sbase/Configuration.h
+++ b/Marlin/src/config/examples/Mks/Sbase/Configuration.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration.h
@ -35,8 +36,6 @@
 * Advanced settings can be found in Configuration_adv.h
 *
 */
-#ifndef CONFIGURATION_H
-#define CONFIGURATION_H
 #define CONFIGURATION_H_VERSION 020000

 //===========================================================================
@ -2031,5 +2030,3 @@

 // Allow servo angle to be edited and saved to EEPROM
 //#define EDITABLE_SERVO_ANGLES
-
-#endif // CONFIGURATION_H
--- a/Marlin/src/config/examples/Mks/Sbase/Configuration_adv.h
+++ b/Marlin/src/config/examples/Mks/Sbase/Configuration_adv.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration_adv.h
@ -30,8 +31,6 @@
 * Basic settings can be found in Configuration.h
 *
 */
-#ifndef CONFIGURATION_ADV_H
-#define CONFIGURATION_ADV_H
 #define CONFIGURATION_ADV_H_VERSION 020000

 // @section temperature
@ -1838,5 +1837,3 @@

 // Enable Marlin dev mode which adds some special commands
 //#define MARLIN_DEV_MODE
-
-#endif // CONFIGURATION_ADV_H
--- a/Marlin/src/config/examples/RepRapPro/Huxley/Configuration.h
+++ b/Marlin/src/config/examples/RepRapPro/Huxley/Configuration.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration.h
@ -35,8 +36,6 @@
 * Advanced settings can be found in Configuration_adv.h
 *
 */
-#ifndef CONFIGURATION_H
-#define CONFIGURATION_H
 #define CONFIGURATION_H_VERSION 020000

 //===========================================================================
@ -2080,5 +2079,3 @@ Black rubber belt(MXL), 18 - tooth aluminium pulley : 87.489 step per mm (Huxley

 // Allow servo angle to be edited and saved to EEPROM
 //#define EDITABLE_SERVO_ANGLES
-
-#endif // CONFIGURATION_H
--- a/Marlin/src/config/examples/RepRapWorld/Megatronics/Configuration.h
+++ b/Marlin/src/config/examples/RepRapWorld/Megatronics/Configuration.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration.h
@ -35,8 +36,6 @@
 * Advanced settings can be found in Configuration_adv.h
 *
 */
-#ifndef CONFIGURATION_H
-#define CONFIGURATION_H
 #define CONFIGURATION_H_VERSION 020000

 //===========================================================================
@ -2031,5 +2030,3 @@

 // Allow servo angle to be edited and saved to EEPROM
 //#define EDITABLE_SERVO_ANGLES
-
-#endif // CONFIGURATION_H
--- a/Marlin/src/config/examples/RigidBot/Configuration.h
+++ b/Marlin/src/config/examples/RigidBot/Configuration.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration.h
@ -35,8 +36,6 @@
 * Advanced settings can be found in Configuration_adv.h
 *
 */
-#ifndef CONFIGURATION_H
-#define CONFIGURATION_H
 #define CONFIGURATION_H_VERSION 020000

 //===========================================================================
@ -2031,5 +2030,3 @@

 // Allow servo angle to be edited and saved to EEPROM
 //#define EDITABLE_SERVO_ANGLES
-
-#endif // CONFIGURATION_H
--- a/Marlin/src/config/examples/RigidBot/Configuration_adv.h
+++ b/Marlin/src/config/examples/RigidBot/Configuration_adv.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration_adv.h
@ -30,8 +31,6 @@
 * Basic settings can be found in Configuration.h
 *
 */
-#ifndef CONFIGURATION_ADV_H
-#define CONFIGURATION_ADV_H
 #define CONFIGURATION_ADV_H_VERSION 020000

 // @section temperature
@ -1830,5 +1829,3 @@

 // Enable Marlin dev mode which adds some special commands
 //#define MARLIN_DEV_MODE
-
-#endif // CONFIGURATION_ADV_H
--- a/Marlin/src/config/examples/SCARA/Configuration.h
+++ b/Marlin/src/config/examples/SCARA/Configuration.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration.h
@ -35,8 +36,6 @@
 * Advanced settings can be found in Configuration_adv.h
 *
 */
-#ifndef CONFIGURATION_H
-#define CONFIGURATION_H
 #define CONFIGURATION_H_VERSION 020000

 //===========================================================================
@ -2044,5 +2043,3 @@

 // Allow servo angle to be edited and saved to EEPROM
 //#define EDITABLE_SERVO_ANGLES
-
-#endif // CONFIGURATION_H
--- a/Marlin/src/config/examples/SCARA/Configuration_adv.h
+++ b/Marlin/src/config/examples/SCARA/Configuration_adv.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration_adv.h
@ -30,8 +31,6 @@
 * Basic settings can be found in Configuration.h
 *
 */
-#ifndef CONFIGURATION_ADV_H
-#define CONFIGURATION_ADV_H
 #define CONFIGURATION_ADV_H_VERSION 020000

 // @section temperature
@ -1830,5 +1829,3 @@

 // Enable Marlin dev mode which adds some special commands
 //#define MARLIN_DEV_MODE
-
-#endif // CONFIGURATION_ADV_H
--- a/Marlin/src/config/examples/STM32F10/Configuration.h
+++ b/Marlin/src/config/examples/STM32F10/Configuration.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration.h
@ -35,8 +36,6 @@
 * Advanced settings can be found in Configuration_adv.h
 *
 */
-#ifndef CONFIGURATION_H
-#define CONFIGURATION_H
 #define CONFIGURATION_H_VERSION 020000

 //===========================================================================
@ -2033,5 +2032,3 @@

 // Allow servo angle to be edited and saved to EEPROM
 //#define EDITABLE_SERVO_ANGLES
-
-#endif // CONFIGURATION_H
--- a/Marlin/src/config/examples/STM32F4/Configuration.h
+++ b/Marlin/src/config/examples/STM32F4/Configuration.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration.h
@ -35,8 +36,6 @@
 * Advanced settings can be found in Configuration_adv.h
 *
 */
-#ifndef CONFIGURATION_H
-#define CONFIGURATION_H
 #define CONFIGURATION_H_VERSION 020000

 //===========================================================================
@ -2031,5 +2030,3 @@

 // Allow servo angle to be edited and saved to EEPROM
 //#define EDITABLE_SERVO_ANGLES
-
-#endif // CONFIGURATION_H
--- a/Marlin/src/config/examples/Sanguinololu/Configuration.h
+++ b/Marlin/src/config/examples/Sanguinololu/Configuration.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration.h
@ -35,8 +36,6 @@
 * Advanced settings can be found in Configuration_adv.h
 *
 */
-#ifndef CONFIGURATION_H
-#define CONFIGURATION_H
 #define CONFIGURATION_H_VERSION 020000

 //===========================================================================
@ -2062,5 +2061,3 @@

 // Allow servo angle to be edited and saved to EEPROM
 //#define EDITABLE_SERVO_ANGLES
-
-#endif // CONFIGURATION_H
--- a/Marlin/src/config/examples/Sanguinololu/Configuration_adv.h
+++ b/Marlin/src/config/examples/Sanguinololu/Configuration_adv.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration_adv.h
@ -30,8 +31,6 @@
 * Basic settings can be found in Configuration.h
 *
 */
-#ifndef CONFIGURATION_ADV_H
-#define CONFIGURATION_ADV_H
 #define CONFIGURATION_ADV_H_VERSION 020000

 // @section temperature
@ -1830,5 +1829,3 @@

 // Enable Marlin dev mode which adds some special commands
 //#define MARLIN_DEV_MODE
-
-#endif // CONFIGURATION_ADV_H
--- a/Marlin/src/config/examples/TheBorg/Configuration.h
+++ b/Marlin/src/config/examples/TheBorg/Configuration.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration.h
@ -35,8 +36,6 @@
 * Advanced settings can be found in Configuration_adv.h
 *
 */
-#ifndef CONFIGURATION_H
-#define CONFIGURATION_H
 #define CONFIGURATION_H_VERSION 020000

 //===========================================================================
@ -2031,5 +2030,3 @@

 // Allow servo angle to be edited and saved to EEPROM
 //#define EDITABLE_SERVO_ANGLES
-
-#endif // CONFIGURATION_H
--- a/Marlin/src/config/examples/TheBorg/Configuration_adv.h
+++ b/Marlin/src/config/examples/TheBorg/Configuration_adv.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration_adv.h
@ -30,8 +31,6 @@
 * Basic settings can be found in Configuration.h
 *
 */
-#ifndef CONFIGURATION_ADV_H
-#define CONFIGURATION_ADV_H
 #define CONFIGURATION_ADV_H_VERSION 020000

 // @section temperature
@ -1830,5 +1829,3 @@

 // Enable Marlin dev mode which adds some special commands
 //#define MARLIN_DEV_MODE
-
-#endif // CONFIGURATION_ADV_H
--- a/Marlin/src/config/examples/TinyBoy2/Configuration.h
+++ b/Marlin/src/config/examples/TinyBoy2/Configuration.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration.h
@ -35,8 +36,6 @@
 * Advanced settings can be found in Configuration_adv.h
 *
 */
-#ifndef CONFIGURATION_H
-#define CONFIGURATION_H
 #define CONFIGURATION_H_VERSION 020000

 /**
@ -2087,5 +2086,3 @@

 // Allow servo angle to be edited and saved to EEPROM
 //#define EDITABLE_SERVO_ANGLES
-
-#endif // CONFIGURATION_H
--- a/Marlin/src/config/examples/TinyBoy2/Configuration_adv.h
+++ b/Marlin/src/config/examples/TinyBoy2/Configuration_adv.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration_adv.h
@ -30,8 +31,6 @@
 * Basic settings can be found in Configuration.h
 *
 */
-#ifndef CONFIGURATION_ADV_H
-#define CONFIGURATION_ADV_H
 #define CONFIGURATION_ADV_H_VERSION 020000

 // @section temperature
@ -1830,5 +1829,3 @@

 // Enable Marlin dev mode which adds some special commands
 //#define MARLIN_DEV_MODE
-
-#endif // CONFIGURATION_ADV_H
--- a/Marlin/src/config/examples/Tronxy/X1/Configuration.h
+++ b/Marlin/src/config/examples/Tronxy/X1/Configuration.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration.h
@ -35,8 +36,6 @@
 * Advanced settings can be found in Configuration_adv.h
 *
 */
-#ifndef CONFIGURATION_H
-#define CONFIGURATION_H
 #define CONFIGURATION_H_VERSION 020000

 //===========================================================================
@ -2031,5 +2030,3 @@

 // Allow servo angle to be edited and saved to EEPROM
 //#define EDITABLE_SERVO_ANGLES
-
-#endif // CONFIGURATION_H
--- a/Marlin/src/config/examples/Tronxy/X3A/Configuration.h
+++ b/Marlin/src/config/examples/Tronxy/X3A/Configuration.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration.h
@ -35,8 +36,6 @@
 * Advanced settings can be found in Configuration_adv.h
 *
 */
-#ifndef CONFIGURATION_H
-#define CONFIGURATION_H
 #define CONFIGURATION_H_VERSION 020000

 //===========================================================================
@ -2035,5 +2034,3 @@

 // Allow servo angle to be edited and saved to EEPROM
 //#define EDITABLE_SERVO_ANGLES
-
-#endif // CONFIGURATION_H
--- a/Marlin/src/config/examples/Tronxy/X3A/Configuration_adv.h
+++ b/Marlin/src/config/examples/Tronxy/X3A/Configuration_adv.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration_adv.h
@ -30,8 +31,6 @@
 * Basic settings can be found in Configuration.h
 *
 */
-#ifndef CONFIGURATION_ADV_H
-#define CONFIGURATION_ADV_H
 #define CONFIGURATION_ADV_H_VERSION 020000

 // @section temperature
@ -1830,5 +1829,3 @@

 // Enable Marlin dev mode which adds some special commands
 //#define MARLIN_DEV_MODE
-
-#endif // CONFIGURATION_ADV_H
--- a/Marlin/src/config/examples/Tronxy/X5S/Configuration.h
+++ b/Marlin/src/config/examples/Tronxy/X5S/Configuration.h
@ -19,6 +19,7 @@
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
+#pragma once

 /**
 * Configuration.h
@ -35,8 +36,6 @@
 * Advanced settings can be found in Configuration_adv.h
 *
 */
-#ifndef CONFIGURATION_H
-#define CONFIGURATION_H
 #define CONFIGURATION_H_VERSION 020000

 //===========================================================================
@ -2031,5 +2030,3 @@

 // Allow servo angle to be edited and saved to EEPROM
 //#define EDITABLE_SERVO_ANGLES
-
-#endif // CONFIGURATION_H