diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h
index 64258a181a..ed218e771c 100644
--- a/Marlin/Configuration.h
+++ b/Marlin/Configuration.h
@@ -1077,6 +1077,11 @@
 // Add a menu item to move between bed corners for manual bed adjustment
 //#define LEVEL_BED_CORNERS
 
+#if ENABLED(LEVEL_BED_CORNERS)
+  #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
+#endif
+
 /**
  * Commands to execute at the end of G29 probing.
  * Useful to retract or move the Z probe out of the way.
diff --git a/Marlin/src/config/default/Configuration.h b/Marlin/src/config/default/Configuration.h
index 64258a181a..ed218e771c 100644
--- a/Marlin/src/config/default/Configuration.h
+++ b/Marlin/src/config/default/Configuration.h
@@ -1077,6 +1077,11 @@
 // Add a menu item to move between bed corners for manual bed adjustment
 //#define LEVEL_BED_CORNERS
 
+#if ENABLED(LEVEL_BED_CORNERS)
+  #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
+#endif
+
 /**
  * Commands to execute at the end of G29 probing.
  * Useful to retract or move the Z probe out of the way.
diff --git a/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration.h b/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration.h
index 84ed1495e4..97deff0e60 100644
--- a/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration.h
+++ b/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration.h
@@ -1097,6 +1097,11 @@
 // Add a menu item to move between bed corners for manual bed adjustment
 //#define LEVEL_BED_CORNERS
 
+#if ENABLED(LEVEL_BED_CORNERS)
+  #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
+#endif
+
 /**
  * Commands to execute at the end of G29 probing.
  * Useful to retract or move the Z probe out of the way.
diff --git a/Marlin/src/config/examples/AliExpress/CL-260/Configuration.h b/Marlin/src/config/examples/AliExpress/CL-260/Configuration.h
index 0c871f9fcf..bea4e28ef3 100644
--- a/Marlin/src/config/examples/AliExpress/CL-260/Configuration.h
+++ b/Marlin/src/config/examples/AliExpress/CL-260/Configuration.h
@@ -1077,6 +1077,11 @@
 // Add a menu item to move between bed corners for manual bed adjustment
 //#define LEVEL_BED_CORNERS
 
+#if ENABLED(LEVEL_BED_CORNERS)
+  #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
+#endif
+
 /**
  * Commands to execute at the end of G29 probing.
  * Useful to retract or move the Z probe out of the way.
diff --git a/Marlin/src/config/examples/Anet/A6/Configuration.h b/Marlin/src/config/examples/Anet/A6/Configuration.h
index d38ac01cd1..f9691003b9 100644
--- a/Marlin/src/config/examples/Anet/A6/Configuration.h
+++ b/Marlin/src/config/examples/Anet/A6/Configuration.h
@@ -1215,6 +1215,11 @@
 // Add a menu item to move between bed corners for manual bed adjustment
 //#define LEVEL_BED_CORNERS
 
+#if ENABLED(LEVEL_BED_CORNERS)
+  #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
+#endif
+
 /**
  * Commands to execute at the end of G29 probing.
  * Useful to retract or move the Z probe out of the way.
diff --git a/Marlin/src/config/examples/Anet/A8/Configuration.h b/Marlin/src/config/examples/Anet/A8/Configuration.h
index 632da57bc2..3ebb2894cc 100644
--- a/Marlin/src/config/examples/Anet/A8/Configuration.h
+++ b/Marlin/src/config/examples/Anet/A8/Configuration.h
@@ -1095,6 +1095,11 @@
 // Add a menu item to move between bed corners for manual bed adjustment
 //#define LEVEL_BED_CORNERS
 
+#if ENABLED(LEVEL_BED_CORNERS)
+  #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
+#endif
+
 /**
  * Commands to execute at the end of G29 probing.
  * Useful to retract or move the Z probe out of the way.
diff --git a/Marlin/src/config/examples/Azteeg/X5GT/Configuration.h b/Marlin/src/config/examples/Azteeg/X5GT/Configuration.h
index 10d0be6d55..1f2c77b663 100644
--- a/Marlin/src/config/examples/Azteeg/X5GT/Configuration.h
+++ b/Marlin/src/config/examples/Azteeg/X5GT/Configuration.h
@@ -1077,6 +1077,11 @@
 // Add a menu item to move between bed corners for manual bed adjustment
 //#define LEVEL_BED_CORNERS
 
+#if ENABLED(LEVEL_BED_CORNERS)
+  #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
+#endif
+
 /**
  * Commands to execute at the end of G29 probing.
  * Useful to retract or move the Z probe out of the way.
diff --git a/Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration.h b/Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration.h
index 88fa590cec..20834e9831 100644
--- a/Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration.h
+++ b/Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration.h
@@ -1077,6 +1077,11 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 // Add a menu item to move between bed corners for manual bed adjustment
 #define LEVEL_BED_CORNERS
 
+#if ENABLED(LEVEL_BED_CORNERS)
+  #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
+#endif
+
 /**
  * Commands to execute at the end of G29 probing.
  * Useful to retract or move the Z probe out of the way.
diff --git a/Marlin/src/config/examples/BIBO/TouchX/default/Configuration.h b/Marlin/src/config/examples/BIBO/TouchX/default/Configuration.h
index af00bcb797..c41063f2ed 100644
--- a/Marlin/src/config/examples/BIBO/TouchX/default/Configuration.h
+++ b/Marlin/src/config/examples/BIBO/TouchX/default/Configuration.h
@@ -1077,6 +1077,11 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 // Add a menu item to move between bed corners for manual bed adjustment
 #define LEVEL_BED_CORNERS
 
+#if ENABLED(LEVEL_BED_CORNERS)
+  #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
+#endif
+
 /**
  * Commands to execute at the end of G29 probing.
  * Useful to retract or move the Z probe out of the way.
diff --git a/Marlin/src/config/examples/BQ/Hephestos/Configuration.h b/Marlin/src/config/examples/BQ/Hephestos/Configuration.h
index 517e7921ee..e4dc07e98e 100644
--- a/Marlin/src/config/examples/BQ/Hephestos/Configuration.h
+++ b/Marlin/src/config/examples/BQ/Hephestos/Configuration.h
@@ -1065,6 +1065,11 @@
 // Add a menu item to move between bed corners for manual bed adjustment
 //#define LEVEL_BED_CORNERS
 
+#if ENABLED(LEVEL_BED_CORNERS)
+  #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
+#endif
+
 /**
  * Commands to execute at the end of G29 probing.
  * Useful to retract or move the Z probe out of the way.
diff --git a/Marlin/src/config/examples/BQ/Hephestos_2/Configuration.h b/Marlin/src/config/examples/BQ/Hephestos_2/Configuration.h
index bd559d2f7d..f743e4e35d 100644
--- a/Marlin/src/config/examples/BQ/Hephestos_2/Configuration.h
+++ b/Marlin/src/config/examples/BQ/Hephestos_2/Configuration.h
@@ -1089,6 +1089,11 @@
 // Add a menu item to move between bed corners for manual bed adjustment
 //#define LEVEL_BED_CORNERS
 
+#if ENABLED(LEVEL_BED_CORNERS)
+  #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
+#endif
+
 /**
  * Commands to execute at the end of G29 probing.
  * Useful to retract or move the Z probe out of the way.
diff --git a/Marlin/src/config/examples/BQ/WITBOX/Configuration.h b/Marlin/src/config/examples/BQ/WITBOX/Configuration.h
index 5e8ff50ed8..6d6a85a02b 100644
--- a/Marlin/src/config/examples/BQ/WITBOX/Configuration.h
+++ b/Marlin/src/config/examples/BQ/WITBOX/Configuration.h
@@ -1065,6 +1065,11 @@
 // Add a menu item to move between bed corners for manual bed adjustment
 //#define LEVEL_BED_CORNERS
 
+#if ENABLED(LEVEL_BED_CORNERS)
+  #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
+#endif
+
 /**
  * Commands to execute at the end of G29 probing.
  * Useful to retract or move the Z probe out of the way.
diff --git a/Marlin/src/config/examples/Cartesio/Configuration.h b/Marlin/src/config/examples/Cartesio/Configuration.h
index 40df14b419..707015ce7c 100644
--- a/Marlin/src/config/examples/Cartesio/Configuration.h
+++ b/Marlin/src/config/examples/Cartesio/Configuration.h
@@ -1076,6 +1076,11 @@
 // Add a menu item to move between bed corners for manual bed adjustment
 //#define LEVEL_BED_CORNERS
 
+#if ENABLED(LEVEL_BED_CORNERS)
+  #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
+#endif
+
 /**
  * Commands to execute at the end of G29 probing.
  * Useful to retract or move the Z probe out of the way.
diff --git a/Marlin/src/config/examples/Creality/CR-10/Configuration.h b/Marlin/src/config/examples/Creality/CR-10/Configuration.h
index eff898141a..91d13f9f6b 100755
--- a/Marlin/src/config/examples/Creality/CR-10/Configuration.h
+++ b/Marlin/src/config/examples/Creality/CR-10/Configuration.h
@@ -1087,6 +1087,11 @@
 // Add a menu item to move between bed corners for manual bed adjustment
 #define LEVEL_BED_CORNERS
 
+#if ENABLED(LEVEL_BED_CORNERS)
+  #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
+#endif
+
 /**
  * Commands to execute at the end of G29 probing.
  * Useful to retract or move the Z probe out of the way.
diff --git a/Marlin/src/config/examples/Creality/CR-10S/Configuration.h b/Marlin/src/config/examples/Creality/CR-10S/Configuration.h
index 77e11e6e7d..3533bfbb9f 100644
--- a/Marlin/src/config/examples/Creality/CR-10S/Configuration.h
+++ b/Marlin/src/config/examples/Creality/CR-10S/Configuration.h
@@ -1078,6 +1078,11 @@
 // Add a menu item to move between bed corners for manual bed adjustment
 #define LEVEL_BED_CORNERS
 
+#if ENABLED(LEVEL_BED_CORNERS)
+  #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
+#endif
+
 /**
  * Commands to execute at the end of G29 probing.
  * Useful to retract or move the Z probe out of the way.
diff --git a/Marlin/src/config/examples/Creality/CR-10mini/Configuration.h b/Marlin/src/config/examples/Creality/CR-10mini/Configuration.h
index 5b0a0889e5..f16b7999c8 100644
--- a/Marlin/src/config/examples/Creality/CR-10mini/Configuration.h
+++ b/Marlin/src/config/examples/Creality/CR-10mini/Configuration.h
@@ -1096,6 +1096,11 @@
 // Add a menu item to move between bed corners for manual bed adjustment
 //#define LEVEL_BED_CORNERS
 
+#if ENABLED(LEVEL_BED_CORNERS)
+  #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
+#endif
+
 /**
  * Commands to execute at the end of G29 probing.
  * Useful to retract or move the Z probe out of the way.
diff --git a/Marlin/src/config/examples/Creality/CR-8/Configuration.h b/Marlin/src/config/examples/Creality/CR-8/Configuration.h
index 8eb9143968..16c6086d38 100644
--- a/Marlin/src/config/examples/Creality/CR-8/Configuration.h
+++ b/Marlin/src/config/examples/Creality/CR-8/Configuration.h
@@ -1087,6 +1087,11 @@
 // Add a menu item to move between bed corners for manual bed adjustment
 //#define LEVEL_BED_CORNERS
 
+#if ENABLED(LEVEL_BED_CORNERS)
+  #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
+#endif
+
 /**
  * Commands to execute at the end of G29 probing.
  * Useful to retract or move the Z probe out of the way.
diff --git a/Marlin/src/config/examples/Creality/Ender-2/Configuration.h b/Marlin/src/config/examples/Creality/Ender-2/Configuration.h
index af703097a6..ff6089adf5 100644
--- a/Marlin/src/config/examples/Creality/Ender-2/Configuration.h
+++ b/Marlin/src/config/examples/Creality/Ender-2/Configuration.h
@@ -1081,6 +1081,11 @@
 // Add a menu item to move between bed corners for manual bed adjustment
 //#define LEVEL_BED_CORNERS
 
+#if ENABLED(LEVEL_BED_CORNERS)
+  #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
+#endif
+
 /**
  * Commands to execute at the end of G29 probing.
  * Useful to retract or move the Z probe out of the way.
diff --git a/Marlin/src/config/examples/Creality/Ender-4/Configuration.h b/Marlin/src/config/examples/Creality/Ender-4/Configuration.h
index 9fbf305737..45c58ae1bb 100644
--- a/Marlin/src/config/examples/Creality/Ender-4/Configuration.h
+++ b/Marlin/src/config/examples/Creality/Ender-4/Configuration.h
@@ -1087,6 +1087,11 @@
 // Add a menu item to move between bed corners for manual bed adjustment
 //#define LEVEL_BED_CORNERS
 
+#if ENABLED(LEVEL_BED_CORNERS)
+  #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
+#endif
+
 /**
  * Commands to execute at the end of G29 probing.
  * Useful to retract or move the Z probe out of the way.
diff --git a/Marlin/src/config/examples/Felix/Configuration.h b/Marlin/src/config/examples/Felix/Configuration.h
index d4637f1fe6..0e9a97f22b 100644
--- a/Marlin/src/config/examples/Felix/Configuration.h
+++ b/Marlin/src/config/examples/Felix/Configuration.h
@@ -1059,6 +1059,11 @@
 // Add a menu item to move between bed corners for manual bed adjustment
 //#define LEVEL_BED_CORNERS
 
+#if ENABLED(LEVEL_BED_CORNERS)
+  #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
+#endif
+
 /**
  * Commands to execute at the end of G29 probing.
  * Useful to retract or move the Z probe out of the way.
diff --git a/Marlin/src/config/examples/Felix/DUAL/Configuration.h b/Marlin/src/config/examples/Felix/DUAL/Configuration.h
index ae304f7458..b0e430c700 100644
--- a/Marlin/src/config/examples/Felix/DUAL/Configuration.h
+++ b/Marlin/src/config/examples/Felix/DUAL/Configuration.h
@@ -1059,6 +1059,11 @@
 // Add a menu item to move between bed corners for manual bed adjustment
 //#define LEVEL_BED_CORNERS
 
+#if ENABLED(LEVEL_BED_CORNERS)
+  #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
+#endif
+
 /**
  * Commands to execute at the end of G29 probing.
  * Useful to retract or move the Z probe out of the way.
diff --git a/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration.h b/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration.h
index 6b5c5c8e98..14bc806359 100644
--- a/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration.h
+++ b/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration.h
@@ -1101,6 +1101,11 @@
 // Add a menu item to move between bed corners for manual bed adjustment
 //#define LEVEL_BED_CORNERS
 
+#if ENABLED(LEVEL_BED_CORNERS)
+  #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
+#endif
+
 /**
  * Commands to execute at the end of G29 probing.
  * Useful to retract or move the Z probe out of the way.
diff --git a/Marlin/src/config/examples/Geeetech/GT2560/Configuration.h b/Marlin/src/config/examples/Geeetech/GT2560/Configuration.h
index c8e5e0d03b..7a1227caa8 100644
--- a/Marlin/src/config/examples/Geeetech/GT2560/Configuration.h
+++ b/Marlin/src/config/examples/Geeetech/GT2560/Configuration.h
@@ -1092,6 +1092,11 @@
 // Add a menu item to move between bed corners for manual bed adjustment
 //#define LEVEL_BED_CORNERS
 
+#if ENABLED(LEVEL_BED_CORNERS)
+  #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
+#endif
+
 /**
  * Commands to execute at the end of G29 probing.
  * Useful to retract or move the Z probe out of the way.
diff --git a/Marlin/src/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h b/Marlin/src/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h
index d315874c2c..785a1c7622 100644
--- a/Marlin/src/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h
+++ b/Marlin/src/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h
@@ -1077,6 +1077,11 @@
 // Add a menu item to move between bed corners for manual bed adjustment
 //#define LEVEL_BED_CORNERS
 
+#if ENABLED(LEVEL_BED_CORNERS)
+  #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
+#endif
+
 /**
  * Commands to execute at the end of G29 probing.
  * Useful to retract or move the Z probe out of the way.
diff --git a/Marlin/src/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h b/Marlin/src/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h
index 11650783ac..12ee32e484 100644
--- a/Marlin/src/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h	
+++ b/Marlin/src/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h	
@@ -1093,6 +1093,11 @@
 // Add a menu item to move between bed corners for manual bed adjustment
 #define LEVEL_BED_CORNERS
 
+#if ENABLED(LEVEL_BED_CORNERS)
+  #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
+#endif
+
 /**
  * Commands to execute at the end of G29 probing.
  * Useful to retract or move the Z probe out of the way.
diff --git a/Marlin/src/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h b/Marlin/src/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h
index 1d6b250b08..97c30cbadd 100644
--- a/Marlin/src/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h	
+++ b/Marlin/src/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h	
@@ -1092,6 +1092,11 @@
 // Add a menu item to move between bed corners for manual bed adjustment
 #define LEVEL_BED_CORNERS
 
+#if ENABLED(LEVEL_BED_CORNERS)
+  #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
+#endif
+
 /**
  * Commands to execute at the end of G29 probing.
  * Useful to retract or move the Z probe out of the way.
diff --git a/Marlin/src/config/examples/Infitary/i3-M508/Configuration.h b/Marlin/src/config/examples/Infitary/i3-M508/Configuration.h
index 1d2758ecd2..d4f61a8181 100644
--- a/Marlin/src/config/examples/Infitary/i3-M508/Configuration.h
+++ b/Marlin/src/config/examples/Infitary/i3-M508/Configuration.h
@@ -1081,6 +1081,11 @@
 // Add a menu item to move between bed corners for manual bed adjustment
 //#define LEVEL_BED_CORNERS
 
+#if ENABLED(LEVEL_BED_CORNERS)
+  #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
+#endif
+
 /**
  * Commands to execute at the end of G29 probing.
  * Useful to retract or move the Z probe out of the way.
diff --git a/Marlin/src/config/examples/JGAurora/A5/Configuration.h b/Marlin/src/config/examples/JGAurora/A5/Configuration.h
index 67712a9214..6986956a75 100644
--- a/Marlin/src/config/examples/JGAurora/A5/Configuration.h
+++ b/Marlin/src/config/examples/JGAurora/A5/Configuration.h
@@ -1088,6 +1088,11 @@
 // Add a menu item to move between bed corners for manual bed adjustment
 #define LEVEL_BED_CORNERS
 
+#if ENABLED(LEVEL_BED_CORNERS)
+  #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
+#endif
+
 /**
  * Commands to execute at the end of G29 probing.
  * Useful to retract or move the Z probe out of the way.
diff --git a/Marlin/src/config/examples/MakerParts/Configuration.h b/Marlin/src/config/examples/MakerParts/Configuration.h
index fff251b577..000fd9778f 100644
--- a/Marlin/src/config/examples/MakerParts/Configuration.h
+++ b/Marlin/src/config/examples/MakerParts/Configuration.h
@@ -1097,6 +1097,11 @@
 // Add a menu item to move between bed corners for manual bed adjustment
 //#define LEVEL_BED_CORNERS
 
+#if ENABLED(LEVEL_BED_CORNERS)
+  #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
+#endif
+
 /**
  * Commands to execute at the end of G29 probing.
  * Useful to retract or move the Z probe out of the way.
diff --git a/Marlin/src/config/examples/Malyan/M150/Configuration.h b/Marlin/src/config/examples/Malyan/M150/Configuration.h
index 84e197f251..a799c51f8a 100644
--- a/Marlin/src/config/examples/Malyan/M150/Configuration.h
+++ b/Marlin/src/config/examples/Malyan/M150/Configuration.h
@@ -1116,6 +1116,11 @@
 // Add a menu item to move between bed corners for manual bed adjustment
 //#define LEVEL_BED_CORNERS
 
+#if ENABLED(LEVEL_BED_CORNERS)
+  #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
+#endif
+
 /**
  * Commands to execute at the end of G29 probing.
  * Useful to retract or move the Z probe out of the way.
diff --git a/Marlin/src/config/examples/Malyan/M200/Configuration.h b/Marlin/src/config/examples/Malyan/M200/Configuration.h
index 339c4502a1..038ffb376e 100644
--- a/Marlin/src/config/examples/Malyan/M200/Configuration.h
+++ b/Marlin/src/config/examples/Malyan/M200/Configuration.h
@@ -1076,6 +1076,11 @@
 // Add a menu item to move between bed corners for manual bed adjustment
 #define LEVEL_BED_CORNERS
 
+#if ENABLED(LEVEL_BED_CORNERS)
+  #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
+#endif
+
 /**
  * Commands to execute at the end of G29 probing.
  * Useful to retract or move the Z probe out of the way.
diff --git a/Marlin/src/config/examples/Micromake/C1/basic/Configuration.h b/Marlin/src/config/examples/Micromake/C1/basic/Configuration.h
index d6a7d4c085..d8f8bb31a7 100644
--- a/Marlin/src/config/examples/Micromake/C1/basic/Configuration.h
+++ b/Marlin/src/config/examples/Micromake/C1/basic/Configuration.h
@@ -1081,6 +1081,11 @@
 // Add a menu item to move between bed corners for manual bed adjustment
 //#define LEVEL_BED_CORNERS
 
+#if ENABLED(LEVEL_BED_CORNERS)
+  #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
+#endif
+
 /**
  * Commands to execute at the end of G29 probing.
  * Useful to retract or move the Z probe out of the way.
diff --git a/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration.h b/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration.h
index 41b536b21c..7d471bca3a 100644
--- a/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration.h
+++ b/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration.h
@@ -1081,6 +1081,11 @@
 // Add a menu item to move between bed corners for manual bed adjustment
 //#define LEVEL_BED_CORNERS
 
+#if ENABLED(LEVEL_BED_CORNERS)
+  #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
+#endif
+
 /**
  * Commands to execute at the end of G29 probing.
  * Useful to retract or move the Z probe out of the way.
diff --git a/Marlin/src/config/examples/Mks/Sbase/Configuration.h b/Marlin/src/config/examples/Mks/Sbase/Configuration.h
index 5f40c3908c..9d9a3aa152 100644
--- a/Marlin/src/config/examples/Mks/Sbase/Configuration.h
+++ b/Marlin/src/config/examples/Mks/Sbase/Configuration.h
@@ -1077,6 +1077,11 @@
 // Add a menu item to move between bed corners for manual bed adjustment
 #define LEVEL_BED_CORNERS
 
+#if ENABLED(LEVEL_BED_CORNERS)
+  #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
+#endif
+
 /**
  * Commands to execute at the end of G29 probing.
  * Useful to retract or move the Z probe out of the way.
diff --git a/Marlin/src/config/examples/RepRapPro/Huxley/Configuration.h b/Marlin/src/config/examples/RepRapPro/Huxley/Configuration.h
index 3cc8104068..e6ccd46d72 100644
--- a/Marlin/src/config/examples/RepRapPro/Huxley/Configuration.h
+++ b/Marlin/src/config/examples/RepRapPro/Huxley/Configuration.h
@@ -1126,6 +1126,11 @@ Black rubber belt(MXL), 18 - tooth aluminium pulley : 87.489 step per mm (Huxley
 // Add a menu item to move between bed corners for manual bed adjustment
 //#define LEVEL_BED_CORNERS
 
+#if ENABLED(LEVEL_BED_CORNERS)
+  #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
+#endif
+
 /**
  * Commands to execute at the end of G29 probing.
  * Useful to retract or move the Z probe out of the way.
diff --git a/Marlin/src/config/examples/RepRapWorld/Megatronics/Configuration.h b/Marlin/src/config/examples/RepRapWorld/Megatronics/Configuration.h
index 6cee845e8d..43846ef426 100644
--- a/Marlin/src/config/examples/RepRapWorld/Megatronics/Configuration.h
+++ b/Marlin/src/config/examples/RepRapWorld/Megatronics/Configuration.h
@@ -1077,6 +1077,11 @@
 // Add a menu item to move between bed corners for manual bed adjustment
 //#define LEVEL_BED_CORNERS
 
+#if ENABLED(LEVEL_BED_CORNERS)
+  #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
+#endif
+
 /**
  * Commands to execute at the end of G29 probing.
  * Useful to retract or move the Z probe out of the way.
diff --git a/Marlin/src/config/examples/RigidBot/Configuration.h b/Marlin/src/config/examples/RigidBot/Configuration.h
index 274dfa2f4e..24219b04af 100644
--- a/Marlin/src/config/examples/RigidBot/Configuration.h
+++ b/Marlin/src/config/examples/RigidBot/Configuration.h
@@ -1075,6 +1075,11 @@
 // Add a menu item to move between bed corners for manual bed adjustment
 //#define LEVEL_BED_CORNERS
 
+#if ENABLED(LEVEL_BED_CORNERS)
+  #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
+#endif
+
 /**
  * Commands to execute at the end of G29 probing.
  * Useful to retract or move the Z probe out of the way.
diff --git a/Marlin/src/config/examples/SCARA/Configuration.h b/Marlin/src/config/examples/SCARA/Configuration.h
index 37038757e5..4d405cfc97 100644
--- a/Marlin/src/config/examples/SCARA/Configuration.h
+++ b/Marlin/src/config/examples/SCARA/Configuration.h
@@ -1090,6 +1090,11 @@
 // Add a menu item to move between bed corners for manual bed adjustment
 //#define LEVEL_BED_CORNERS
 
+#if ENABLED(LEVEL_BED_CORNERS)
+  #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
+#endif
+
 /**
  * Commands to execute at the end of G29 probing.
  * Useful to retract or move the Z probe out of the way.
diff --git a/Marlin/src/config/examples/STM32F10/Configuration.h b/Marlin/src/config/examples/STM32F10/Configuration.h
index 10b2cb3282..159d212910 100644
--- a/Marlin/src/config/examples/STM32F10/Configuration.h
+++ b/Marlin/src/config/examples/STM32F10/Configuration.h
@@ -1080,6 +1080,11 @@
 // Add a menu item to move between bed corners for manual bed adjustment
 //#define LEVEL_BED_CORNERS
 
+#if ENABLED(LEVEL_BED_CORNERS)
+  #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
+#endif
+
 /**
  * Commands to execute at the end of G29 probing.
  * Useful to retract or move the Z probe out of the way.
diff --git a/Marlin/src/config/examples/STM32F4/Configuration.h b/Marlin/src/config/examples/STM32F4/Configuration.h
index 7636003048..de67b28c56 100644
--- a/Marlin/src/config/examples/STM32F4/Configuration.h
+++ b/Marlin/src/config/examples/STM32F4/Configuration.h
@@ -1077,6 +1077,11 @@
 // Add a menu item to move between bed corners for manual bed adjustment
 //#define LEVEL_BED_CORNERS
 
+#if ENABLED(LEVEL_BED_CORNERS)
+  #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
+#endif
+
 /**
  * Commands to execute at the end of G29 probing.
  * Useful to retract or move the Z probe out of the way.
diff --git a/Marlin/src/config/examples/Sanguinololu/Configuration.h b/Marlin/src/config/examples/Sanguinololu/Configuration.h
index d307e2dd1e..9d9daafbbf 100644
--- a/Marlin/src/config/examples/Sanguinololu/Configuration.h
+++ b/Marlin/src/config/examples/Sanguinololu/Configuration.h
@@ -1108,6 +1108,11 @@
 // Add a menu item to move between bed corners for manual bed adjustment
 //#define LEVEL_BED_CORNERS
 
+#if ENABLED(LEVEL_BED_CORNERS)
+  #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
+#endif
+
 /**
  * Commands to execute at the end of G29 probing.
  * Useful to retract or move the Z probe out of the way.
diff --git a/Marlin/src/config/examples/TheBorg/Configuration.h b/Marlin/src/config/examples/TheBorg/Configuration.h
index 3e77d576da..98aad2d7f9 100644
--- a/Marlin/src/config/examples/TheBorg/Configuration.h
+++ b/Marlin/src/config/examples/TheBorg/Configuration.h
@@ -1077,6 +1077,11 @@
 // Add a menu item to move between bed corners for manual bed adjustment
 //#define LEVEL_BED_CORNERS
 
+#if ENABLED(LEVEL_BED_CORNERS)
+  #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
+#endif
+
 /**
  * Commands to execute at the end of G29 probing.
  * Useful to retract or move the Z probe out of the way.
diff --git a/Marlin/src/config/examples/TinyBoy2/Configuration.h b/Marlin/src/config/examples/TinyBoy2/Configuration.h
index 33adf7a53c..8422f7ce6e 100644
--- a/Marlin/src/config/examples/TinyBoy2/Configuration.h
+++ b/Marlin/src/config/examples/TinyBoy2/Configuration.h
@@ -1133,6 +1133,11 @@
 // Add a menu item to move between bed corners for manual bed adjustment
 //#define LEVEL_BED_CORNERS
 
+#if ENABLED(LEVEL_BED_CORNERS)
+  #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
+#endif
+
 /**
  * Commands to execute at the end of G29 probing.
  * Useful to retract or move the Z probe out of the way.
diff --git a/Marlin/src/config/examples/Tronxy/X1/Configuration.h b/Marlin/src/config/examples/Tronxy/X1/Configuration.h
index c48bfb12b6..021bb9a453 100644
--- a/Marlin/src/config/examples/Tronxy/X1/Configuration.h
+++ b/Marlin/src/config/examples/Tronxy/X1/Configuration.h
@@ -1077,6 +1077,11 @@
 // Add a menu item to move between bed corners for manual bed adjustment
 #define LEVEL_BED_CORNERS
 
+#if ENABLED(LEVEL_BED_CORNERS)
+  #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
+#endif
+
 /**
  * Commands to execute at the end of G29 probing.
  * Useful to retract or move the Z probe out of the way.
diff --git a/Marlin/src/config/examples/Tronxy/X5S/Configuration.h b/Marlin/src/config/examples/Tronxy/X5S/Configuration.h
index 45eb828c85..dea4652bf9 100644
--- a/Marlin/src/config/examples/Tronxy/X5S/Configuration.h
+++ b/Marlin/src/config/examples/Tronxy/X5S/Configuration.h
@@ -1077,6 +1077,11 @@
 // Add a menu item to move between bed corners for manual bed adjustment
 #define LEVEL_BED_CORNERS
 
+#if ENABLED(LEVEL_BED_CORNERS)
+  #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
+#endif
+
 /**
  * Commands to execute at the end of G29 probing.
  * Useful to retract or move the Z probe out of the way.
diff --git a/Marlin/src/config/examples/Tronxy/XY100/Configuration.h b/Marlin/src/config/examples/Tronxy/XY100/Configuration.h
index 32ab20251e..b22d24aa22 100644
--- a/Marlin/src/config/examples/Tronxy/XY100/Configuration.h
+++ b/Marlin/src/config/examples/Tronxy/XY100/Configuration.h
@@ -1088,6 +1088,11 @@
 // Add a menu item to move between bed corners for manual bed adjustment
 //#define LEVEL_BED_CORNERS
 
+#if ENABLED(LEVEL_BED_CORNERS)
+  #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
+#endif
+
 /**
  * Commands to execute at the end of G29 probing.
  * Useful to retract or move the Z probe out of the way.
diff --git a/Marlin/src/config/examples/UltiMachine/Archim2/Configuration.h b/Marlin/src/config/examples/UltiMachine/Archim2/Configuration.h
index c2f7e72d0d..75796866ab 100644
--- a/Marlin/src/config/examples/UltiMachine/Archim2/Configuration.h
+++ b/Marlin/src/config/examples/UltiMachine/Archim2/Configuration.h
@@ -1077,6 +1077,11 @@
 // Add a menu item to move between bed corners for manual bed adjustment
 //#define LEVEL_BED_CORNERS
 
+#if ENABLED(LEVEL_BED_CORNERS)
+  #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
+#endif
+
 /**
  * Commands to execute at the end of G29 probing.
  * Useful to retract or move the Z probe out of the way.
diff --git a/Marlin/src/config/examples/Velleman/K8200/Configuration.h b/Marlin/src/config/examples/Velleman/K8200/Configuration.h
index 7784e4055a..bac37eb7cb 100644
--- a/Marlin/src/config/examples/Velleman/K8200/Configuration.h
+++ b/Marlin/src/config/examples/Velleman/K8200/Configuration.h
@@ -1107,6 +1107,11 @@
 // Add a menu item to move between bed corners for manual bed adjustment
 //#define LEVEL_BED_CORNERS
 
+#if ENABLED(LEVEL_BED_CORNERS)
+  #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
+#endif
+
 /**
  * Commands to execute at the end of G29 probing.
  * Useful to retract or move the Z probe out of the way.
diff --git a/Marlin/src/config/examples/Velleman/K8400/Configuration.h b/Marlin/src/config/examples/Velleman/K8400/Configuration.h
index c49ec753f7..4e5375853f 100644
--- a/Marlin/src/config/examples/Velleman/K8400/Configuration.h
+++ b/Marlin/src/config/examples/Velleman/K8400/Configuration.h
@@ -1077,6 +1077,11 @@
 // Add a menu item to move between bed corners for manual bed adjustment
 //#define LEVEL_BED_CORNERS
 
+#if ENABLED(LEVEL_BED_CORNERS)
+  #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
+#endif
+
 /**
  * Commands to execute at the end of G29 probing.
  * Useful to retract or move the Z probe out of the way.
diff --git a/Marlin/src/config/examples/Velleman/K8400/Dual-head/Configuration.h b/Marlin/src/config/examples/Velleman/K8400/Dual-head/Configuration.h
index 6787408e79..942c905188 100644
--- a/Marlin/src/config/examples/Velleman/K8400/Dual-head/Configuration.h
+++ b/Marlin/src/config/examples/Velleman/K8400/Dual-head/Configuration.h
@@ -1077,6 +1077,11 @@
 // Add a menu item to move between bed corners for manual bed adjustment
 //#define LEVEL_BED_CORNERS
 
+#if ENABLED(LEVEL_BED_CORNERS)
+  #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
+#endif
+
 /**
  * Commands to execute at the end of G29 probing.
  * Useful to retract or move the Z probe out of the way.
diff --git a/Marlin/src/config/examples/Wanhao/Duplicator 6/Configuration.h b/Marlin/src/config/examples/Wanhao/Duplicator 6/Configuration.h
index c3d79d361c..e657dcf8c6 100644
--- a/Marlin/src/config/examples/Wanhao/Duplicator 6/Configuration.h	
+++ b/Marlin/src/config/examples/Wanhao/Duplicator 6/Configuration.h	
@@ -1084,6 +1084,11 @@
 // Add a menu item to move between bed corners for manual bed adjustment
 //#define LEVEL_BED_CORNERS
 
+#if ENABLED(LEVEL_BED_CORNERS)
+  #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
+#endif
+
 /**
  * Commands to execute at the end of G29 probing.
  * Useful to retract or move the Z probe out of the way.
diff --git a/Marlin/src/config/examples/adafruit/ST7565/Configuration.h b/Marlin/src/config/examples/adafruit/ST7565/Configuration.h
index 2e4e8d0b8b..4dedbce9b6 100644
--- a/Marlin/src/config/examples/adafruit/ST7565/Configuration.h
+++ b/Marlin/src/config/examples/adafruit/ST7565/Configuration.h
@@ -1077,6 +1077,11 @@
 // Add a menu item to move between bed corners for manual bed adjustment
 //#define LEVEL_BED_CORNERS
 
+#if ENABLED(LEVEL_BED_CORNERS)
+  #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
+#endif
+
 /**
  * Commands to execute at the end of G29 probing.
  * Useful to retract or move the Z probe out of the way.
diff --git a/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration.h b/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration.h
index 73bd69972a..7515d0749f 100644
--- a/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration.h
+++ b/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration.h
@@ -1228,6 +1228,11 @@
 // Add a menu item to move between bed corners for manual bed adjustment
 //#define LEVEL_BED_CORNERS
 
+#if ENABLED(LEVEL_BED_CORNERS)
+  #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
+#endif
+
 /**
  * Commands to execute at the end of G29 probing.
  * Useful to retract or move the Z probe out of the way.
diff --git a/Marlin/src/config/examples/delta/FLSUN/kossel/Configuration.h b/Marlin/src/config/examples/delta/FLSUN/kossel/Configuration.h
index 5e9a715452..73dccf0fd4 100644
--- a/Marlin/src/config/examples/delta/FLSUN/kossel/Configuration.h
+++ b/Marlin/src/config/examples/delta/FLSUN/kossel/Configuration.h
@@ -1210,6 +1210,11 @@
 // Add a menu item to move between bed corners for manual bed adjustment
 //#define LEVEL_BED_CORNERS
 
+#if ENABLED(LEVEL_BED_CORNERS)
+  #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
+#endif
+
 /**
  * Commands to execute at the end of G29 probing.
  * Useful to retract or move the Z probe out of the way.
diff --git a/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration.h b/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration.h
index 228fa2f75d..2fe5f17e1a 100644
--- a/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration.h
+++ b/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration.h
@@ -1209,6 +1209,11 @@
 // Add a menu item to move between bed corners for manual bed adjustment
 //#define LEVEL_BED_CORNERS
 
+#if ENABLED(LEVEL_BED_CORNERS)
+  #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
+#endif
+
 /**
  * Commands to execute at the end of G29 probing.
  * Useful to retract or move the Z probe out of the way.
diff --git a/Marlin/src/config/examples/delta/Hatchbox_Alpha/Configuration.h b/Marlin/src/config/examples/delta/Hatchbox_Alpha/Configuration.h
index 67dd248a91..13213e3cdb 100644
--- a/Marlin/src/config/examples/delta/Hatchbox_Alpha/Configuration.h
+++ b/Marlin/src/config/examples/delta/Hatchbox_Alpha/Configuration.h
@@ -1223,6 +1223,11 @@
 // Add a menu item to move between bed corners for manual bed adjustment
 //#define LEVEL_BED_CORNERS
 
+#if ENABLED(LEVEL_BED_CORNERS)
+  #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
+#endif
+
 /**
  * Commands to execute at the end of G29 probing.
  * Useful to retract or move the Z probe out of the way.
diff --git a/Marlin/src/config/examples/delta/generic/Configuration.h b/Marlin/src/config/examples/delta/generic/Configuration.h
index a3464642f1..cb1c2771b9 100644
--- a/Marlin/src/config/examples/delta/generic/Configuration.h
+++ b/Marlin/src/config/examples/delta/generic/Configuration.h
@@ -1197,6 +1197,11 @@
 // Add a menu item to move between bed corners for manual bed adjustment
 //#define LEVEL_BED_CORNERS
 
+#if ENABLED(LEVEL_BED_CORNERS)
+  #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
+#endif
+
 /**
  * Commands to execute at the end of G29 probing.
  * Useful to retract or move the Z probe out of the way.
diff --git a/Marlin/src/config/examples/delta/kossel_mini/Configuration.h b/Marlin/src/config/examples/delta/kossel_mini/Configuration.h
index 5a8eb0d80b..4fbffa4ba8 100644
--- a/Marlin/src/config/examples/delta/kossel_mini/Configuration.h
+++ b/Marlin/src/config/examples/delta/kossel_mini/Configuration.h
@@ -1200,6 +1200,11 @@
 // Add a menu item to move between bed corners for manual bed adjustment
 //#define LEVEL_BED_CORNERS
 
+#if ENABLED(LEVEL_BED_CORNERS)
+  #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
+#endif
+
 /**
  * Commands to execute at the end of G29 probing.
  * Useful to retract or move the Z probe out of the way.
diff --git a/Marlin/src/config/examples/delta/kossel_pro/Configuration.h b/Marlin/src/config/examples/delta/kossel_pro/Configuration.h
index 2eae24eeb6..47430ba14c 100644
--- a/Marlin/src/config/examples/delta/kossel_pro/Configuration.h
+++ b/Marlin/src/config/examples/delta/kossel_pro/Configuration.h
@@ -1200,6 +1200,11 @@
 // Add a menu item to move between bed corners for manual bed adjustment
 //#define LEVEL_BED_CORNERS
 
+#if ENABLED(LEVEL_BED_CORNERS)
+  #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
+#endif
+
 /**
  * Commands to execute at the end of G29 probing.
  * Useful to retract or move the Z probe out of the way.
diff --git a/Marlin/src/config/examples/delta/kossel_xl/Configuration.h b/Marlin/src/config/examples/delta/kossel_xl/Configuration.h
index c4a9ec7d42..fb929a0710 100644
--- a/Marlin/src/config/examples/delta/kossel_xl/Configuration.h
+++ b/Marlin/src/config/examples/delta/kossel_xl/Configuration.h
@@ -1200,6 +1200,11 @@
 // Add a menu item to move between bed corners for manual bed adjustment
 //#define LEVEL_BED_CORNERS
 
+#if ENABLED(LEVEL_BED_CORNERS)
+  #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
+#endif
+
 /**
  * Commands to execute at the end of G29 probing.
  * Useful to retract or move the Z probe out of the way.
diff --git a/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration.h b/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration.h
index 8a3fd065da..61fc5f51ff 100644
--- a/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration.h
+++ b/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration.h
@@ -1098,6 +1098,11 @@
 // Add a menu item to move between bed corners for manual bed adjustment
 //#define LEVEL_BED_CORNERS
 
+#if ENABLED(LEVEL_BED_CORNERS)
+  #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
+#endif
+
 /**
  * Commands to execute at the end of G29 probing.
  * Useful to retract or move the Z probe out of the way.
diff --git a/Marlin/src/config/examples/makibox/Configuration.h b/Marlin/src/config/examples/makibox/Configuration.h
index fa75a70413..794918d312 100644
--- a/Marlin/src/config/examples/makibox/Configuration.h
+++ b/Marlin/src/config/examples/makibox/Configuration.h
@@ -1080,6 +1080,11 @@
 // Add a menu item to move between bed corners for manual bed adjustment
 //#define LEVEL_BED_CORNERS
 
+#if ENABLED(LEVEL_BED_CORNERS)
+  #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
+#endif
+
 /**
  * Commands to execute at the end of G29 probing.
  * Useful to retract or move the Z probe out of the way.
diff --git a/Marlin/src/config/examples/stm32f103ret6/Configuration.h b/Marlin/src/config/examples/stm32f103ret6/Configuration.h
index 347564c7e1..11abf8de60 100644
--- a/Marlin/src/config/examples/stm32f103ret6/Configuration.h
+++ b/Marlin/src/config/examples/stm32f103ret6/Configuration.h
@@ -1078,6 +1078,11 @@
 // Add a menu item to move between bed corners for manual bed adjustment
 //#define LEVEL_BED_CORNERS
 
+#if ENABLED(LEVEL_BED_CORNERS)
+  #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
+#endif
+
 /**
  * Commands to execute at the end of G29 probing.
  * Useful to retract or move the Z probe out of the way.
diff --git a/Marlin/src/config/examples/tvrrug/Round2/Configuration.h b/Marlin/src/config/examples/tvrrug/Round2/Configuration.h
index b99134350d..83b435ce80 100644
--- a/Marlin/src/config/examples/tvrrug/Round2/Configuration.h
+++ b/Marlin/src/config/examples/tvrrug/Round2/Configuration.h
@@ -1072,6 +1072,11 @@
 // Add a menu item to move between bed corners for manual bed adjustment
 //#define LEVEL_BED_CORNERS
 
+#if ENABLED(LEVEL_BED_CORNERS)
+  #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
+#endif
+
 /**
  * Commands to execute at the end of G29 probing.
  * Useful to retract or move the Z probe out of the way.
diff --git a/Marlin/src/config/examples/wt150/Configuration.h b/Marlin/src/config/examples/wt150/Configuration.h
index 7971ab651c..c7e779ca45 100644
--- a/Marlin/src/config/examples/wt150/Configuration.h
+++ b/Marlin/src/config/examples/wt150/Configuration.h
@@ -1082,6 +1082,11 @@
 // Add a menu item to move between bed corners for manual bed adjustment
 //#define LEVEL_BED_CORNERS
 
+#if ENABLED(LEVEL_BED_CORNERS)
+  #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
+#endif
+
 /**
  * Commands to execute at the end of G29 probing.
  * Useful to retract or move the Z probe out of the way.
diff --git a/Marlin/src/inc/SanityCheck.h b/Marlin/src/inc/SanityCheck.h
index 165690a2a1..fe30e07aa6 100644
--- a/Marlin/src/inc/SanityCheck.h
+++ b/Marlin/src/inc/SanityCheck.h
@@ -270,6 +270,8 @@
   #error "AUTOMATIC_CURRENT_CONTROL is now MONITOR_DRIVER_STATUS. Please update your configuration."
 #elif defined(FILAMENT_CHANGE_LOAD_LENGTH)
   #error "FILAMENT_CHANGE_LOAD_LENGTH is now FILAMENT_CHANGE_FAST_LOAD_LENGTH. Please update your configuration."
+#elif ENABLED(LEVEL_BED_CORNERS) && !defined(LEVEL_CORNERS_INSET)
+  #error "LEVEL_BED_CORNERS requires a LEVEL_CORNERS_INSET value. Please update your Configuration.h."
 #endif
 
 #define BOARD_MKS_13     -47
diff --git a/Marlin/src/lcd/ultralcd.cpp b/Marlin/src/lcd/ultralcd.cpp
index a633b6a8d1..af19eade33 100644
--- a/Marlin/src/lcd/ultralcd.cpp
+++ b/Marlin/src/lcd/ultralcd.cpp
@@ -1834,27 +1834,43 @@ void kill_screen(const char* lcd_msg) {
       line_to_z(4.0);
       switch (bed_corner) {
         case 0:
-          current_position[X_AXIS] = X_MIN_BED + 10;
-          current_position[Y_AXIS] = Y_MIN_BED + 10;
+          current_position[X_AXIS] = X_MIN_BED + LEVEL_CORNERS_INSET;
+          current_position[Y_AXIS] = Y_MIN_BED + LEVEL_CORNERS_INSET;
           break;
         case 1:
-          current_position[X_AXIS] = X_MAX_BED - 10;
+          current_position[X_AXIS] = X_MAX_BED - LEVEL_CORNERS_INSET;
           break;
         case 2:
-          current_position[Y_AXIS] = Y_MAX_BED - 10;
+          current_position[Y_AXIS] = Y_MAX_BED - LEVEL_CORNERS_INSET;
           break;
         case 3:
-          current_position[X_AXIS] = X_MIN_BED + 10;
+          current_position[X_AXIS] = X_MIN_BED + LEVEL_CORNERS_INSET;
           break;
+        #if ENABLED(LEVEL_CENTER_TOO)
+          case 4:
+            current_position[X_AXIS] = X_CENTER;
+            current_position[Y_AXIS] = Y_CENTER;
+            break;
+        #endif
       }
       planner.buffer_line_kinematic(current_position, MMM_TO_MMS(manual_feedrate_mm_m[X_AXIS]), active_extruder);
       line_to_z(0.0);
-      if (++bed_corner > 3) bed_corner = 0;
+      if (++bed_corner > 3
+        #if ENABLED(LEVEL_CENTER_TOO)
+          + 1
+        #endif
+      ) bed_corner = 0;
     }
 
     void _lcd_corner_submenu() {
       START_MENU();
-      MENU_ITEM(function, MSG_NEXT_CORNER, _lcd_goto_next_corner);
+      MENU_ITEM(function,
+        #if ENABLED(LEVEL_CENTER_TOO)
+          MSG_LEVEL_BED_NEXT_POINT
+        #else
+          MSG_NEXT_CORNER
+        #endif
+        , _lcd_goto_next_corner);
       MENU_ITEM(function, MSG_BACK, lcd_goto_previous_menu_no_defer);
       END_MENU();
     }