Browse Source

Load balance some tests

vanilla_fb_2.0.x
Scott Lahteine 5 years ago
parent
commit
9b886c2ad4
  1. 11
      Marlin/src/pins/rambo/pins_RAMBO.h
  2. 8
      Marlin/src/pins/ramps/pins_RAMPS.h
  3. 37
      buildroot/share/tests/mega2560-tests
  4. 35
      buildroot/share/tests/rambo-tests

11
Marlin/src/pins/rambo/pins_RAMBO.h

@ -72,6 +72,10 @@
#define Z_MIN_PROBE_PIN 30 #define Z_MIN_PROBE_PIN 30
#endif #endif
#ifndef FIL_RUNOUT_PIN
#define FIL_RUNOUT_PIN 5
#endif
// //
// Steppers // Steppers
// //
@ -153,6 +157,13 @@
#define SPINDLE_LASER_ENA_PIN 31 // Pullup! #define SPINDLE_LASER_ENA_PIN 31 // Pullup!
#define SPINDLE_DIR_PIN 32 #define SPINDLE_DIR_PIN 32
//
// SPI for Max6675 or Max31855 Thermocouple
//
#ifndef MAX6675_SS_PIN
#define MAX6675_SS_PIN 32 // SPINDLE_DIR_PIN / STAT_LED_BLUE_PIN
#endif
// //
// M7/M8/M9 - Coolant Control // M7/M8/M9 - Coolant Control
// //

8
Marlin/src/pins/ramps/pins_RAMPS.h

@ -169,11 +169,11 @@
#define TEMP_BED_PIN 14 // Analog Input #define TEMP_BED_PIN 14 // Analog Input
#endif #endif
//
// SPI for Max6675 or Max31855 Thermocouple // SPI for Max6675 or Max31855 Thermocouple
#if DISABLED(SDSUPPORT) //
#define MAX6675_SS_PIN 66 // Don't use 53 if using Display/SD card #ifndef MAX6675_SS_PIN
#else #define MAX6675_SS_PIN 66 // Don't use 53 if using Display/SD card (SDSS) or 49 (SD_DETECT_PIN)
#define MAX6675_SS_PIN 66 // Don't use 49 (SD_DETECT_PIN)
#endif #endif
// //

37
buildroot/share/tests/mega2560-tests

@ -12,43 +12,6 @@ set -e
#restore_configs #restore_configs
#exec_test $1 $2 "Default Configuration" #exec_test $1 $2 "Default Configuration"
#
# Test 2 extruders (one MAX6675) and heated bed on basic RAMPS 1.4
# Test a "Fix Mounted" Probe with Safe Homing, some arc options,
# linear bed leveling, M48, leveling debug, and firmware retraction.
#
restore_configs
opt_set MOTHERBOARD BOARD_RAMPS_14_EEB
opt_set EXTRUDERS 2
opt_set TEMP_SENSOR_0 -2
opt_set TEMP_SENSOR_1 1
opt_set TEMP_SENSOR_BED 2
opt_set TEMP_SENSOR_PROBE 1
opt_add TEMP_PROBE_PIN 12
opt_set TEMP_SENSOR_CHAMBER 3
opt_add HEATER_CHAMBER_PIN 45
opt_set GRID_MAX_POINTS_X 16
opt_set FANMUX0_PIN 53
opt_disable USE_WATCHDOG
opt_enable REPRAP_DISCOUNT_SMART_CONTROLLER LCD_PROGRESS_BAR LCD_PROGRESS_BAR_TEST \
FIX_MOUNTED_PROBE Z_SAFE_HOMING CODEPENDENT_XY_HOMING PIDTEMPBED \
PROBING_HEATERS_OFF PROBING_FANS_OFF PROBING_STEPPERS_OFF WAIT_FOR_BED_HEATER \
EEPROM_SETTINGS SDSUPPORT SD_REPRINT_LAST_SELECTED_FILE BINARY_FILE_TRANSFER \
BLINKM PCA9632 RGB_LED RGB_LED_R_PIN RGB_LED_G_PIN RGB_LED_B_PIN LED_CONTROL_MENU \
NEOPIXEL_LED CASE_LIGHT_ENABLE CASE_LIGHT_USE_NEOPIXEL CASE_LIGHT_MENU \
PID_PARAMS_PER_HOTEND PID_AUTOTUNE_MENU PID_EDIT_MENU LCD_SHOW_E_TOTAL \
PRINTCOUNTER SERVICE_NAME_1 SERVICE_INTERVAL_1 LEVEL_BED_CORNERS \
NOZZLE_PARK_FEATURE FILAMENT_RUNOUT_SENSOR FILAMENT_RUNOUT_DISTANCE_MM \
ADVANCED_PAUSE_FEATURE FILAMENT_LOAD_UNLOAD_GCODES FILAMENT_UNLOAD_ALL_EXTRUDERS \
AUTO_BED_LEVELING_BILINEAR Z_MIN_PROBE_REPEATABILITY_TEST DISTINCT_E_FACTORS \
SKEW_CORRECTION SKEW_CORRECTION_FOR_Z SKEW_CORRECTION_GCODE \
BACKLASH_COMPENSATION BACKLASH_GCODE BAUD_RATE_GCODE BEZIER_CURVE_SUPPORT \
FWRETRACT ARC_P_CIRCLES CNC_WORKSPACE_PLANES CNC_COORDINATE_SYSTEMS \
PSU_CONTROL AUTO_POWER_CONTROL POWER_LOSS_RECOVERY POWER_LOSS_PIN POWER_LOSS_STATE \
SLOW_PWM_HEATERS THERMAL_PROTECTION_CHAMBER LIN_ADVANCE EXTRA_LIN_ADVANCE_K \
HOST_ACTION_COMMANDS HOST_PROMPT_SUPPORT PINS_DEBUGGING MAX7219_DEBUG M114_DETAIL
exec_test $1 $2 "RAMPS | EXTRUDERS 2 | CHAR LCD + SD | FIX Probe | ABL-Linear | Advanced Pause | PLR | LEDs ..."
# #
# Test a probeless build of AUTO_BED_LEVELING_UBL, with lots of extruders # Test a probeless build of AUTO_BED_LEVELING_UBL, with lots of extruders
# #

35
buildroot/share/tests/rambo-tests

@ -33,5 +33,40 @@ opt_enable USE_XMAX_PLUG USE_YMAX_PLUG USE_ZMAX_PLUG \
opt_disable MIN_SOFTWARE_ENDSTOP_Z MAX_SOFTWARE_ENDSTOPS opt_disable MIN_SOFTWARE_ENDSTOP_Z MAX_SOFTWARE_ENDSTOPS
exec_test $1 $2 "Rambo CNC Configuration" exec_test $1 $2 "Rambo CNC Configuration"
#
# Lots of options - Formerly the first Mega2560 test
#
restore_configs
opt_set MOTHERBOARD BOARD_RAMBO
opt_set EXTRUDERS 2
opt_set TEMP_SENSOR_0 -2
opt_set TEMP_SENSOR_1 1
opt_set TEMP_SENSOR_BED 2
opt_set TEMP_SENSOR_PROBE 1
opt_add TEMP_PROBE_PIN 12
opt_set TEMP_SENSOR_CHAMBER 3
opt_add HEATER_CHAMBER_PIN 45
opt_set GRID_MAX_POINTS_X 16
opt_set FANMUX0_PIN 53
opt_disable USE_WATCHDOG
opt_enable REPRAP_DISCOUNT_SMART_CONTROLLER LCD_PROGRESS_BAR LCD_PROGRESS_BAR_TEST \
FIX_MOUNTED_PROBE Z_SAFE_HOMING CODEPENDENT_XY_HOMING PIDTEMPBED \
PROBING_HEATERS_OFF PROBING_FANS_OFF PROBING_STEPPERS_OFF WAIT_FOR_BED_HEATER \
EEPROM_SETTINGS SDSUPPORT SD_REPRINT_LAST_SELECTED_FILE BINARY_FILE_TRANSFER \
BLINKM PCA9632 RGB_LED RGB_LED_R_PIN RGB_LED_G_PIN RGB_LED_B_PIN LED_CONTROL_MENU \
NEOPIXEL_LED CASE_LIGHT_ENABLE CASE_LIGHT_USE_NEOPIXEL CASE_LIGHT_MENU \
PID_PARAMS_PER_HOTEND PID_AUTOTUNE_MENU PID_EDIT_MENU LCD_SHOW_E_TOTAL \
PRINTCOUNTER SERVICE_NAME_1 SERVICE_INTERVAL_1 LEVEL_BED_CORNERS \
NOZZLE_PARK_FEATURE FILAMENT_RUNOUT_SENSOR FILAMENT_RUNOUT_DISTANCE_MM \
ADVANCED_PAUSE_FEATURE FILAMENT_LOAD_UNLOAD_GCODES FILAMENT_UNLOAD_ALL_EXTRUDERS \
AUTO_BED_LEVELING_BILINEAR Z_MIN_PROBE_REPEATABILITY_TEST DISTINCT_E_FACTORS \
SKEW_CORRECTION SKEW_CORRECTION_FOR_Z SKEW_CORRECTION_GCODE \
BACKLASH_COMPENSATION BACKLASH_GCODE BAUD_RATE_GCODE BEZIER_CURVE_SUPPORT \
FWRETRACT ARC_P_CIRCLES CNC_WORKSPACE_PLANES CNC_COORDINATE_SYSTEMS \
PSU_CONTROL AUTO_POWER_CONTROL POWER_LOSS_RECOVERY POWER_LOSS_PIN POWER_LOSS_STATE \
SLOW_PWM_HEATERS THERMAL_PROTECTION_CHAMBER LIN_ADVANCE EXTRA_LIN_ADVANCE_K \
HOST_ACTION_COMMANDS HOST_PROMPT_SUPPORT PINS_DEBUGGING MAX7219_DEBUG M114_DETAIL
exec_test $1 $2 "RAMBO | EXTRUDERS 2 | CHAR LCD + SD | FIX Probe | ABL-Linear | Advanced Pause | PLR | LEDs ..."
# clean up # clean up
restore_configs restore_configs

Loading…
Cancel
Save