🔧 Normal FET layout with Spindle/Laser (#23409)

Marlin/src/pins/mega/pins_HJC2560C_REV2.h

@@ -112,7 +112,7 @@
 //
 // M3/M4/M5 - Spindle/Laser Control
 //
-#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
+#if HAS_CUTTER
   #define SPINDLE_DIR_PIN                     16
   #define SPINDLE_LASER_ENA_PIN               17  // Pin should have a pullup!
   #define SPINDLE_LASER_PWM_PIN                9  // Hardware PWM

Marlin/src/pins/pins.h

@@ -45,7 +45,7 @@
   #define FET_ORDER_EFF 1
 #elif MB(RAMPS_13_EEF, RAMPS_14_EEF, RAMPS_PLUS_EEF, RAMPS_14_RE_ARM_EEF, RAMPS_SMART_EEF, RAMPS_DUO_EEF, RAMPS4DUE_EEF)
   #define FET_ORDER_EEF 1
-#elif MB(RAMPS_13_SF,  RAMPS_14_SF,  RAMPS_PLUS_SF,  RAMPS_14_RE_ARM_SF,  RAMPS_SMART_SF,  RAMPS_DUO_SF,  RAMPS4DUE_SF) || EITHER(SPINDLE_FEATURE, LASER_FEATURE)
+#elif MB(RAMPS_13_SF,  RAMPS_14_SF,  RAMPS_PLUS_SF,  RAMPS_14_RE_ARM_SF,  RAMPS_SMART_SF,  RAMPS_DUO_SF,  RAMPS4DUE_SF)
   #define FET_ORDER_SF 1
 #elif HAS_MULTI_HOTEND && TEMP_SENSOR_BED
   #define FET_ORDER_EEB 1

Marlin/src/pins/ramps/pins_TT_OSCAR.h

@@ -226,7 +226,7 @@
 //
 // M3/M4/M5 - Spindle/Laser Control
 //
-#if EITHER(SPINDLE_FEATURE, LASER_FEATURE) && !PIN_EXISTS(SPINDLE_LASER_ENA)
+#if HAS_CUTTER && !PIN_EXISTS(SPINDLE_LASER_ENA)
   #if !NUM_SERVOS                                 // Prefer the servo connector
     #define SPINDLE_LASER_ENA_PIN              4  // Pullup or pulldown!
     #define SPINDLE_LASER_PWM_PIN              6  // Hardware PWM

Marlin/src/pins/sanguino/pins_SANGUINOLOLU_11.h

@@ -135,7 +135,7 @@
   #define LCD_BACKLIGHT_PIN                   17  // LCD backlight LED
 #endif
 
-#if NONE(SPINDLE_FEATURE, LASER_FEATURE) && ENABLED(SANGUINOLOLU_V_1_2) && !BOTH(IS_ULTRA_LCD, IS_NEWPANEL) // try to use IO Header
+#if !HAS_CUTTER && ENABLED(SANGUINOLOLU_V_1_2) && !BOTH(IS_ULTRA_LCD, IS_NEWPANEL) // try to use IO Header
   #define CASE_LIGHT_PIN                       4  // Hardware PWM  - see if IO Header is available
 #endif
 

Marlin/src/pins/stm32f4/pins_BTT_SKR_V2_0_common.h

@@ -253,7 +253,7 @@
   #define FAN_PIN                           PB7   // Fan0
 #endif
 
-#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
+#if HAS_CUTTER
   #ifndef SPINDLE_LASER_PWM_PIN
     #define SPINDLE_LASER_PWM_PIN           PB5
   #endif