Bob-the-Kuhn
8 years ago
committed by
Scott Lahteine
Scott Lahteine
41 changed files with 3709 additions and 10 deletions
File diff suppressed because it is too large
File diff suppressed because it is too large
@ -0,0 +1,274 @@ |
|||||
|
/**
|
||||
|
* Marlin 3D Printer Firmware |
||||
|
* Copyright (C) 2017 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
||||
|
* |
||||
|
* Based on Sprinter and grbl. |
||||
|
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm |
||||
|
* |
||||
|
* This program is free software: you can redistribute it and/or modify |
||||
|
* it under the terms of the GNU General Public License as published by |
||||
|
* the Free Software Foundation, either version 3 of the License, or |
||||
|
* (at your option) any later version. |
||||
|
* |
||||
|
* This program is distributed in the hope that it will be useful, |
||||
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of |
||||
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
||||
|
* GNU General Public License for more details. |
||||
|
* |
||||
|
* You should have received a copy of the GNU General Public License |
||||
|
* along with this program. If not, see <http://www.gnu.org/licenses/>.
|
||||
|
* |
||||
|
*/ |
||||
|
|
||||
|
/**
|
||||
|
* Anet V1.0 board pin assignments |
||||
|
*/ |
||||
|
|
||||
|
/**
|
||||
|
* Rev B 16 JUN 2017 |
||||
|
* |
||||
|
* 1) no longer uses Sanguino files to define some of the pins |
||||
|
* 2) added pointers to useable Arduino IDE extensions |
||||
|
* |
||||
|
*/ |
||||
|
|
||||
|
/**
|
||||
|
* The standard Arduino IDE extension (board manager) for this board |
||||
|
* is located at https://github.com/SkyNet3D/anet-board.
|
||||
|
* |
||||
|
* Installation instructions are on that page. |
||||
|
* |
||||
|
* After copying the files to the appropriate location, restart Arduino and |
||||
|
* you'll see "Anet V1.0" and "Anet V1.0 (Optiboot)" in the boards list. |
||||
|
* |
||||
|
* "Anet V1.0" uses the bootloader that was installed on the board when |
||||
|
* it shipped from the factory. |
||||
|
* |
||||
|
* "Anet V1.0 (Optiboot)" frees up another 3K of FLASH. You'll need to burn |
||||
|
* a new bootloader to the board to be able to automatically download a |
||||
|
* compiled image. |
||||
|
* |
||||
|
*/ |
||||
|
|
||||
|
/**
|
||||
|
* Another usable Arduino IDE extension (board manager) can be found at |
||||
|
* https://github.com/Lauszus/Sanguino
|
||||
|
* |
||||
|
* This extension has been tested on Arduino 1.6.12 & 1.8.0 |
||||
|
* |
||||
|
* Here's the JSON path: |
||||
|
* https://raw.githubusercontent.com/Lauszus/Sanguino/master/package_lauszus_sanguino_index.json
|
||||
|
* |
||||
|
* When installing select 1.0.2 |
||||
|
* |
||||
|
* Installation instructions can be found at https://learn.sparkfun.com/pages/CustomBoardsArduino
|
||||
|
* Just use the above JSON URL instead of Sparkfun's JSON. |
||||
|
* |
||||
|
* Once installed select the Sanguino board and then select the CPU. |
||||
|
* |
||||
|
*/ |
||||
|
|
||||
|
/**
|
||||
|
* To burn a new bootloader: |
||||
|
* |
||||
|
* 1. Connect your programmer to the board. |
||||
|
* 2. In the Arduino IDE select the board and then select the programmer. |
||||
|
* 3. In the Arduino IDE click on "burn bootloader". Don't worry about the "verify failed at 1F000" error message. |
||||
|
* 4. The programmer is no longer needed. Remove it. |
||||
|
*/ |
||||
|
|
||||
|
/**
|
||||
|
* Additional info: |
||||
|
* |
||||
|
* Anet Schematics - https://github.com/ralf-e/ANET-3D-Board-V1.0
|
||||
|
* Wiring RRDFG Smart Controller - http://www.thingiverse.com/thing:2103748
|
||||
|
* SkyNet3D Anet software development - https://github.com/SkyNet3D/Marlin/
|
||||
|
* Anet Users / Skynet SW on Facebook - https://www.facebook.com/skynet3ddevelopment/
|
||||
|
* |
||||
|
* Many thanks to Hans Raaf (@oderwat) for developing the Anet-specific software and supporting the Anet community. |
||||
|
*/ |
||||
|
|
||||
|
#if !defined(__AVR_ATmega1284P__) |
||||
|
#error "Oops! Make sure you have 'Anet V1.0', 'Anet V1.0 (Optiboot)' or 'Sanguino' selected from the 'Tools -> Boards' menu." |
||||
|
#endif |
||||
|
|
||||
|
#ifndef BOARD_NAME |
||||
|
#define BOARD_NAME "Anet" |
||||
|
#endif |
||||
|
|
||||
|
#define LARGE_FLASH true |
||||
|
|
||||
|
//
|
||||
|
// Limit Switches
|
||||
|
//
|
||||
|
#define X_STOP_PIN 18 |
||||
|
#define Y_STOP_PIN 19 |
||||
|
#define Z_STOP_PIN 20 |
||||
|
|
||||
|
//
|
||||
|
// Steppers
|
||||
|
//
|
||||
|
#define X_STEP_PIN 15 |
||||
|
#define X_DIR_PIN 21 |
||||
|
#define X_ENABLE_PIN 14 |
||||
|
|
||||
|
#define Y_STEP_PIN 22 |
||||
|
#define Y_DIR_PIN 23 |
||||
|
#define Y_ENABLE_PIN 14 |
||||
|
|
||||
|
#define Z_STEP_PIN 3 |
||||
|
#define Z_DIR_PIN 2 |
||||
|
#define Z_ENABLE_PIN 26 |
||||
|
|
||||
|
#define E0_STEP_PIN 1 |
||||
|
#define E0_DIR_PIN 0 |
||||
|
#define E0_ENABLE_PIN 14 |
||||
|
|
||||
|
//
|
||||
|
// Temperature Sensors
|
||||
|
//
|
||||
|
#define TEMP_0_PIN 7 // Analog Input (pin 33 extruder)
|
||||
|
#define TEMP_BED_PIN 6 // Analog Input (pin 34 bed)
|
||||
|
|
||||
|
//
|
||||
|
// Heaters / Fans
|
||||
|
//
|
||||
|
#define HEATER_0_PIN 13 // (extruder)
|
||||
|
#define HEATER_BED_PIN 12 // (bed)
|
||||
|
#define FAN_PIN 4 |
||||
|
|
||||
|
//
|
||||
|
// Misc. Functions
|
||||
|
//
|
||||
|
#define SDSS 31 |
||||
|
#define LED_PIN -1 |
||||
|
|
||||
|
/**
|
||||
|
* LCD / Controller |
||||
|
* |
||||
|
* Only the following displays are supported: |
||||
|
* ANET_KEYPAD_LCD |
||||
|
* ANET_FULL_GRAPHICS_LCD |
||||
|
* REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER |
||||
|
*/ |
||||
|
|
||||
|
#if ENABLED(ULTRA_LCD) && ENABLED(NEWPANEL) |
||||
|
#define LCD_SDSS 28 |
||||
|
#if ENABLED(ADC_KEYPAD) |
||||
|
#define SERVO0_PIN 27 // free for BLTouch/3D-Touch
|
||||
|
#define LCD_PINS_RS 28 |
||||
|
#define LCD_PINS_ENABLE 29 |
||||
|
#define LCD_PINS_D4 10 |
||||
|
#define LCD_PINS_D5 11 |
||||
|
#define LCD_PINS_D6 16 |
||||
|
#define LCD_PINS_D7 17 |
||||
|
#define BTN_EN1 -1 |
||||
|
#define BTN_EN2 -1 |
||||
|
#define BTN_ENC -1 |
||||
|
#define ADC_KEYPAD_PIN 1 |
||||
|
#define ENCODER_FEEDRATE_DEADZONE 2 |
||||
|
#elif ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) || ENABLED(ANET_FULL_GRAPHICS_LCD) |
||||
|
// Pin definitions for the Anet A6 Full Graphics display and the RepRapDiscount Full Graphics
|
||||
|
// display using an adapter board // https://go.aisler.net/benlye/anet-lcd-adapter/pcb
|
||||
|
// See below for alternative pin definitions for use with https://www.thingiverse.com/thing:2103748
|
||||
|
#define SERVO0_PIN 29 // free for BLTouch/3D-Touch
|
||||
|
#define BEEPER_PIN 17 |
||||
|
#define LCD_PINS_RS 27 |
||||
|
#define LCD_PINS_ENABLE 28 |
||||
|
#define LCD_PINS_D4 30 |
||||
|
#define BTN_EN1 11 |
||||
|
#define BTN_EN2 10 |
||||
|
#define BTN_ENC 16 |
||||
|
#define ST7920_DELAY_1 DELAY_0_NOP |
||||
|
#define ST7920_DELAY_2 DELAY_1_NOP |
||||
|
#define ST7920_DELAY_3 DELAY_2_NOP |
||||
|
#ifndef ENCODER_STEPS_PER_MENU_ITEM |
||||
|
#define ENCODER_STEPS_PER_MENU_ITEM 1 |
||||
|
#endif |
||||
|
#ifndef ENCODER_PULSES_PER_STEP |
||||
|
#define ENCODER_PULSES_PER_STEP 4 |
||||
|
#endif |
||||
|
#endif |
||||
|
#endif // ULTRA_LCD && NEWPANEL
|
||||
|
|
||||
|
/**
|
||||
|
* ==================================================================== |
||||
|
* =============== Alternative RepRapDiscount Wiring ================== |
||||
|
* ==================================================================== |
||||
|
* |
||||
|
* An alternative wiring scheme for the RepRapDiscount Full Graphics Display is |
||||
|
* published by oderwat on Thingiverse at https://www.thingiverse.com/thing:2103748.
|
||||
|
* |
||||
|
* Using that adapter requires changing the pin definition as follows: |
||||
|
* #define SERVO0_PIN 27 // free for BLTouch/3D-Touch
|
||||
|
* #define BEEPER_PIN 28 |
||||
|
* #define LCD_PINS_RS 30 |
||||
|
* #define LCD_PINS_ENABLE 29 |
||||
|
* #define LCD_PINS_D4 17 |
||||
|
* |
||||
|
* The BLTouch pin becomes LCD:3 |
||||
|
*/ |
||||
|
|
||||
|
/**
|
||||
|
* ==================================================================== |
||||
|
* ===================== LCD PINOUTS ================================== |
||||
|
* ==================================================================== |
||||
|
* |
||||
|
* Anet V1.0 controller | ANET_KEYPAD_LCD | ANET_FULL_ | RepRapDiscount Full | Thingiverse RepRap wiring |
||||
|
* physical logical alt | | GRAPHICS_LCD | Graphics Display Wiring | http://www.thingiverse
|
||||
|
* pin pin functions | | | | .com/thing:2103748 |
||||
|
*------------------------------------------------------------------------------------------------------------------------ |
||||
|
* ANET-J3.1 8 *** | N/A | J3_TX *** | | |
||||
|
* ANET-J3.2 9 *** | N/A | J3_RX *** | | |
||||
|
* ANET-J3.3 6 MISO | N/A | MISO *** | EXP2.1 MISO | EXP2.1 MISO |
||||
|
* ANET-J3.4 +5V | N/A | +5V | | |
||||
|
* ANET-J3.5 7 SCK | N/A | SCK *** | EXP2.2 SCK | EXP2.2 SCK |
||||
|
* ANET-J3.6 5 MOSI | N/A | MOSI *** | EXP2.6 MOSI | EXP2.6 MOSI |
||||
|
* ANET-J3.7 !RESET | N/A | button | EXP2.8 panel button | EXP2.8 panel button |
||||
|
* ANET-J3.8 GND | N/A | GND | EXP2.9 GND | EXP2.9 GND |
||||
|
* ANET-J3.9 4 Don't use | N/A | N/C | | |
||||
|
* ANET-J3.10 +3.3V | N/A | +3.3V *** | | |
||||
|
* | | | | |
||||
|
* | | | | |
||||
|
* ANET-LCD.1 GND | GND | GND | EXP1.9 GND | EXP1.9 GND |
||||
|
* ANET-LCD.2 +5V | +5V | +5V | EXP1.10 +5V | EXP1.10 +5V |
||||
|
* ANET-LCD.3 27 A4 | N/C * | LCD_PINS_RS | EXP1.4 LCD_PINS_RS | EXP2.4 SDSS or N/C * |
||||
|
* ANET-LCD.4 10 | LCD_PINS_D4 | BTN_EN2 | EXP2.3 BTN_EN2 | EXP2.3 BTN_EN2 |
||||
|
* ANET-LCD.5 28 A3 | LCD_PINS_RS | LCD_PINS_ENABLE | EXP1.3 LCD_PINS_ENABLE | EXP1.1 BEEPER_PIN |
||||
|
* ANET-LCD.6 11 | LCD_PINS_D5 | BTN_EN1 | EXP2.5 BTN_EN1 | EXP2.5 BTN_EN1 |
||||
|
* ANET-LCD.7 29 A2 | LCD_PINS_ENABLE | N/C * | EXP2.4 SDSS or N/C * | EXP1.3 LCD_PINS_ENABLE |
||||
|
* ANET-LCD.8 16 SCL | LCD_PINS_D6 | BTN_ENC | EXP1.2 BTN_ENC | EXP1.2 BTN_ENC |
||||
|
* ANET-LCD.9 30 A1 | ADC_KEYPAD_PIN ** | LCD_PINS_D4 | EXP1.5 LCD_PINS_D4 | EXP1.4 LCD_PINS_RS |
||||
|
* ANET-LCD.10 17 SDA | LCD_PINS_D7 | BEEPER_PIN | EXP1.1 BEEPER_PIN | EXP1.5 LCD_PINS_D4 |
||||
|
* |
||||
|
* N/C * - if not connected to the LCD can be used for BLTouch servo input |
||||
|
* ** - analog pin -WITHOUT a pullup |
||||
|
* *** - only connected to something if the Bluetooth module is populated |
||||
|
*/ |
||||
|
|
||||
|
/**
|
||||
|
* REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER |
||||
|
* physical pin function |
||||
|
* EXP1.1 BEEPER |
||||
|
* EXP1.2 BTN_ENC |
||||
|
* EXP1.3 LCD_PINS_ENABLE |
||||
|
* EXP1.4 LCD_PINS_RS |
||||
|
* EXP1.5 LCD_PINS_D4 |
||||
|
* EXP1.6 LCD_PINS_D5 (not used) |
||||
|
* EXP1.7 LCD_PINS_D6 (not used) |
||||
|
* EXP1.8 LCD_PINS_D7 (not used) |
||||
|
* EXP1.9 GND |
||||
|
* EXP1.10 VCC |
||||
|
* |
||||
|
* |
||||
|
* EXP2.1 MISO |
||||
|
* EXP2.2 SCK |
||||
|
* EXP2.3 BTN_EN2 |
||||
|
* EXP2.4 SDSS |
||||
|
* EXP2.5 BTN_EN1 |
||||
|
* EXP2.6 MOSI |
||||
|
* EXP2.7 SD_DETECT_PIN |
||||
|
* EXP2.8 button |
||||
|
* EXP2.9 GND |
||||
|
* EXP2.10 NC |
||||
|
*/ |
||||
Loading…
Reference in new issue