diff --git a/Marlin/src/config/examples/Creality/Ender-3/Configuration.h b/Marlin/src/config/examples/Creality/Ender-3/Configuration.h new file mode 100644 index 0000000000..d3a0b7dd6e --- /dev/null +++ b/Marlin/src/config/examples/Creality/Ender-3/Configuration.h @@ -0,0 +1,1889 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ + +/** + * Configuration.h + * + * Basic settings such as: + * + * - Type of electronics + * - Type of temperature sensor + * - Printer geometry + * - Endstop configuration + * - LCD controller + * - Extra features + * + * Advanced settings can be found in Configuration_adv.h + * + */ +#ifndef CONFIGURATION_H +#define CONFIGURATION_H +#define CONFIGURATION_H_VERSION 020000 + +//=========================================================================== +//============================= Getting Started ============================= +//=========================================================================== + +/** + * Here are some standard links for getting your machine calibrated: + * + * http://reprap.org/wiki/Calibration + * http://youtu.be/wAL9d7FgInk + * http://calculator.josefprusa.cz + * http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide + * http://www.thingiverse.com/thing:5573 + * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap + * http://www.thingiverse.com/thing:298812 + */ + +//=========================================================================== +//============================= DELTA Printer =============================== +//=========================================================================== +// For a Delta printer start with one of the configuration files in the +// config/examples/delta directory and customize for your machine. +// + +//=========================================================================== +//============================= SCARA Printer =============================== +//=========================================================================== +// For a SCARA printer start with the configuration files in +// config/examples/SCARA and customize for your machine. +// + +// @section info + +// User-specified version info of this build to display in [Pronterface, etc] terminal window during +// startup. Implementation of an idea by Prof Braino to inform user that any changes made to this +// build by the user have been successfully uploaded into firmware. +#define STRING_CONFIG_H_AUTHOR "(thisiskeithb, Ender-3)" // Who made the changes. +#define SHOW_BOOTSCREEN +#define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during bootup in line 1 +#define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during bootup in line 2 + +/** + * *** VENDORS PLEASE READ *** + * + * Marlin allows you to add a custom boot image for Graphical LCDs. + * With this option Marlin will first show your custom screen followed + * by the standard Marlin logo with version number and web URL. + * + * We encourage you to take advantage of this new feature and we also + * respecfully request that you retain the unmodified Marlin boot screen. + */ + +// Enable to show the bitmap in Marlin/_Bootscreen.h on startup. +#define SHOW_CUSTOM_BOOTSCREEN + +// Enable to show the bitmap in Marlin/_Statusscreen.h on the status screen. +#define CUSTOM_STATUS_SCREEN_IMAGE + +// @section machine + +/** + * Select the serial port on the board to use for communication with the host. + * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. + * + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] + */ +#define SERIAL_PORT 0 + +/** + * Select a secondary serial port on the board to use for communication with the host. + * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. + * + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] + */ +#define SERIAL_PORT_2 -1 + +/** + * This setting determines the communication speed of the printer. + * + * 250000 works in most cases, but you might try a lower speed if + * you commonly experience drop-outs during host printing. + * You may try up to 1000000 to speed up SD file transfer. + * + * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000] + */ +#define BAUDRATE 115200 + +// Enable the Bluetooth serial interface on AT90USB devices +//#define BLUETOOTH + +// The following define selects which electronics board you have. +// Please choose the name from boards.h that matches your setup +#ifndef MOTHERBOARD + #define MOTHERBOARD BOARD_MELZI_CREALITY +#endif + +// Optional custom name for your RepStrap or other custom machine +// Displayed in the LCD "Ready" message +#define CUSTOM_MACHINE_NAME "Ender-3" + +// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) +// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +//#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" + +// @section extruder + +// This defines the number of extruders +// :[1, 2, 3, 4, 5] +#define EXTRUDERS 1 + +// Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc. +#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75 + +// For Cyclops or any "multi-extruder" that shares a single nozzle. +//#define SINGLENOZZLE + +/** + * Průša MK2 Single Nozzle Multi-Material Multiplexer, and variants. + * + * This device allows one stepper driver on a control board to drive + * two to eight stepper motors, one at a time, in a manner suitable + * for extruders. + * + * This option only allows the multiplexer to switch on tool-change. + * Additional options to configure custom E moves are pending. + */ +//#define MK2_MULTIPLEXER +#if ENABLED(MK2_MULTIPLEXER) + // Override the default DIO selector pins here, if needed. + // Some pins files may provide defaults for these pins. + //#define E_MUX0_PIN 40 // Always Required + //#define E_MUX1_PIN 42 // Needed for 3 to 8 steppers + //#define E_MUX2_PIN 44 // Needed for 5 to 8 steppers +#endif + +// A dual extruder that uses a single stepper motor +//#define SWITCHING_EXTRUDER +#if ENABLED(SWITCHING_EXTRUDER) + #define SWITCHING_EXTRUDER_SERVO_NR 0 + #define SWITCHING_EXTRUDER_SERVO_ANGLES { 0, 90 } // Angles for E0, E1[, E2, E3] + #if EXTRUDERS > 3 + #define SWITCHING_EXTRUDER_E23_SERVO_NR 1 + #endif +#endif + +// A dual-nozzle that uses a servomotor to raise/lower one of the nozzles +//#define SWITCHING_NOZZLE +#if ENABLED(SWITCHING_NOZZLE) + #define SWITCHING_NOZZLE_SERVO_NR 0 + #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 + //#define HOTEND_OFFSET_Z { 0.0, 0.0 } +#endif + +/** + * Two separate X-carriages with extruders that connect to a moving part + * via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN. + */ +//#define PARKING_EXTRUDER +#if ENABLED(PARKING_EXTRUDER) + #define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage + #define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil + #define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined. + #define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders + #define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder + #define PARKING_EXTRUDER_SECURITY_RAISE 5 // Z-raise before parking + #define HOTEND_OFFSET_Z { 0.0, 1.3 } // Z-offsets of the two hotends. The first must be 0. +#endif + +/** + * "Mixing Extruder" + * - Adds a new code, M165, to set the current mix factors. + * - Extends the stepping routines to move multiple steppers in proportion to the mix. + * - Optional support for Repetier Firmware M163, M164, and virtual extruder. + * - This implementation supports only a single extruder. + * - Enable DIRECT_MIXING_IN_G1 for Pia Taubert's reference implementation + */ +//#define MIXING_EXTRUDER +#if ENABLED(MIXING_EXTRUDER) + #define MIXING_STEPPERS 2 // Number of steppers in your mixing extruder + #define MIXING_VIRTUAL_TOOLS 16 // Use the Virtual Tool method with M163 and M164 + //#define DIRECT_MIXING_IN_G1 // Allow ABCDHI mix factors in G1 movement commands +#endif + +// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing). +// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder). +// For the other hotends it is their distance from the extruder 0 hotend. +//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis +//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis + +// @section machine + +/** + * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN + * + * 0 = No Power Switch + * 1 = ATX + * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC) + * + * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' } + */ +#define POWER_SUPPLY 0 + +#if POWER_SUPPLY > 0 + // Enable this option to leave the PSU off at startup. + // Power to steppers and heaters will need to be turned on with M80. + //#define PS_DEFAULT_OFF + + //#define AUTO_POWER_CONTROL // Enable automatic control of the PS_ON pin + #if ENABLED(AUTO_POWER_CONTROL) + #define AUTO_POWER_FANS // Turn on PSU if fans need power + #define AUTO_POWER_E_FANS + #define AUTO_POWER_CONTROLLERFAN + #define POWER_TIMEOUT 30 + #endif + +#endif + +// @section temperature + +//=========================================================================== +//============================= Thermal Settings ============================ +//=========================================================================== + +/** + * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table + * + * Temperature sensors available: + * + * -3 : thermocouple with MAX31855 (only for sensor 0) + * -2 : thermocouple with MAX6675 (only for sensor 0) + * -1 : thermocouple with AD595 + * 0 : not used + * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 3 : Mendel-parts thermistor (4.7k pullup) + * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! + * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) + * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) + * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) + * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) + * 8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) + * 9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup) + * 10 : 100k RS thermistor 198-961 (4.7k pullup) + * 11 : 100k beta 3950 1% thermistor (4.7k pullup) + * 12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed) + * 13 : 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE" + * 15 : 100k thermistor calibration for JGAurora A5 hotend + * 20 : the PT100 circuit found in the Ultimainboard V2.x + * 60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950 + * 66 : 4.7M High Temperature thermistor from Dyze Design + * 70 : the 100K thermistor found in the bq Hephestos 2 + * 75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor + * + * 1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k. + * (but gives greater accuracy and more stable PID) + * 51 : 100k thermistor - EPCOS (1k pullup) + * 52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup) + * 55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup) + * + * 1047 : Pt1000 with 4k7 pullup + * 1010 : Pt1000 with 1k pullup (non standard) + * 147 : Pt100 with 4k7 pullup + * 110 : Pt100 with 1k pullup (non standard) + * + * Use these for Testing or Development purposes. NEVER for production machine. + * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. + * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. + * + * :{ '0': "Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '66':"Dyze Design 4.7M High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595",'998':"Dummy 1", '999':"Dummy 2" } + */ +#define TEMP_SENSOR_0 1 +#define TEMP_SENSOR_1 0 +#define TEMP_SENSOR_2 0 +#define TEMP_SENSOR_3 0 +#define TEMP_SENSOR_4 0 +#define TEMP_SENSOR_BED 1 +#define TEMP_SENSOR_CHAMBER 0 + +// Dummy thermistor constant temperature readings, for use with 998 and 999 +#define DUMMY_THERMISTOR_998_VALUE 25 +#define DUMMY_THERMISTOR_999_VALUE 100 + +// Use temp sensor 1 as a redundant sensor with sensor 0. If the readings +// from the two sensors differ too much the print will be aborted. +//#define TEMP_SENSOR_1_AS_REDUNDANT +#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 + +// Extruder temperature must be close to target for this long before M109 returns success +#define TEMP_RESIDENCY_TIME 10 // (seconds) +#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one +#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early. + +// Bed temperature must be close to target for this long before M190 returns success +#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) +#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one +#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early. + +// The minimal temperature defines the temperature below which the heater will not be enabled It is used +// to check that the wiring to the thermistor is not broken. +// Otherwise this would lead to the heater being powered on all the time. +#define HEATER_0_MINTEMP 5 +#define HEATER_1_MINTEMP 5 +#define HEATER_2_MINTEMP 5 +#define HEATER_3_MINTEMP 5 +#define HEATER_4_MINTEMP 5 +#define BED_MINTEMP 5 + +// When temperature exceeds max temp, your heater will be switched off. +// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! +// You should use MINTEMP for thermistor short/failure protection. +#define HEATER_0_MAXTEMP 275 +#define HEATER_1_MAXTEMP 275 +#define HEATER_2_MAXTEMP 275 +#define HEATER_3_MAXTEMP 275 +#define HEATER_4_MAXTEMP 275 +#define BED_MAXTEMP 125 + +//=========================================================================== +//============================= PID Settings ================================ +//=========================================================================== +// PID Tuning Guide here: http://reprap.org/wiki/PID_Tuning + +// Comment the following line to disable PID and enable bang-bang. +#define PIDTEMP +#define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current +#define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current +#define PID_K1 0.95 // Smoothing factor within any PID loop +#if ENABLED(PIDTEMP) + #define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result. + //#define PID_DEBUG // Sends debug data to the serial port. + //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX + //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay + //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders) + // Set/get with gcode: M301 E[extruder number, 0-2] + #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature + // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max. + + // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it + // Creality Ender-3 + #define DEFAULT_Kp 21.73 + #define DEFAULT_Ki 1.54 + #define DEFAULT_Kd 76.55 + + // Ultimaker + //#define DEFAULT_Kp 22.2 + //#define DEFAULT_Ki 1.08 + //#define DEFAULT_Kd 114 + + // MakerGear + //#define DEFAULT_Kp 7.0 + //#define DEFAULT_Ki 0.1 + //#define DEFAULT_Kd 12 + + // Mendel Parts V9 on 12V + //#define DEFAULT_Kp 63.0 + //#define DEFAULT_Ki 2.25 + //#define DEFAULT_Kd 440 + +#endif // PIDTEMP + +//=========================================================================== +//============================= PID > Bed Temperature Control =============== +//=========================================================================== + +/** + * PID Bed Heating + * + * If this option is enabled set PID constants below. + * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis. + * + * The PID frequency will be the same as the extruder PWM. + * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz, + * which is fine for driving a square wave into a resistive load and does not significantly + * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W + * heater. If your configuration is significantly different than this and you don't understand + * the issues involved, don't use bed PID until someone else verifies that your hardware works. + */ +//#define PIDTEMPBED + +//#define BED_LIMIT_SWITCHING + +/** + * Max Bed Power + * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis). + * When set to any value below 255, enables a form of PWM to the bed that acts like a divider + * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED) + */ +#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current + +#if ENABLED(PIDTEMPBED) + + //#define PID_BED_DEBUG // Sends debug data to the serial port. + + //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) + //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) + #define DEFAULT_bedKp 10.00 + #define DEFAULT_bedKi .023 + #define DEFAULT_bedKd 305.4 + + //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) + //from pidautotune + //#define DEFAULT_bedKp 97.1 + //#define DEFAULT_bedKi 1.41 + //#define DEFAULT_bedKd 1675.16 + + // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. +#endif // PIDTEMPBED + +// @section extruder + +// This option prevents extrusion if the temperature is below EXTRUDE_MINTEMP. +// It also enables the M302 command to set the minimum extrusion temperature +// or to allow moving the extruder regardless of the hotend temperature. +// *** IT IS HIGHLY RECOMMENDED TO LEAVE THIS OPTION ENABLED! *** +#define PREVENT_COLD_EXTRUSION +#define EXTRUDE_MINTEMP 170 + +// This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH. +// Note that for Bowden Extruders a too-small value here may prevent loading. +#define PREVENT_LENGTHY_EXTRUDE +#define EXTRUDE_MAXLENGTH 200 + +//=========================================================================== +//======================== Thermal Runaway Protection ======================= +//=========================================================================== + +/** + * Thermal Protection provides additional protection to your printer from damage + * and fire. Marlin always includes safe min and max temperature ranges which + * protect against a broken or disconnected thermistor wire. + * + * The issue: If a thermistor falls out, it will report the much lower + * temperature of the air in the room, and the the firmware will keep + * the heater on. + * + * If you get "Thermal Runaway" or "Heating failed" errors the + * details can be tuned in Configuration_adv.h + */ + +#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders +#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed + +//=========================================================================== +//============================= Mechanical Settings ========================= +//=========================================================================== + +// @section machine + +// Uncomment one of these options to enable CoreXY, CoreXZ, or CoreYZ kinematics +// either in the usual order or reversed +//#define COREXY +//#define COREXZ +//#define COREYZ +//#define COREYX +//#define COREZX +//#define COREZY + +//=========================================================================== +//============================== Endstop Settings =========================== +//=========================================================================== + +// @section homing + +// Specify here all the endstop connectors that are connected to any endstop or probe. +// Almost all printers will be using one per axis. Probes will use one or more of the +// extra connectors. Leave undefined any used for non-endstop and non-probe purposes. +#define USE_XMIN_PLUG +#define USE_YMIN_PLUG +#define USE_ZMIN_PLUG +//#define USE_XMAX_PLUG +//#define USE_YMAX_PLUG +//#define USE_ZMAX_PLUG + +// Enable pullup for all endstops to prevent a floating state +#define ENDSTOPPULLUPS +#if DISABLED(ENDSTOPPULLUPS) + // Disable ENDSTOPPULLUPS to set pullups individually + //#define ENDSTOPPULLUP_XMAX + //#define ENDSTOPPULLUP_YMAX + //#define ENDSTOPPULLUP_ZMAX + //#define ENDSTOPPULLUP_XMIN + //#define ENDSTOPPULLUP_YMIN + //#define ENDSTOPPULLUP_ZMIN + //#define ENDSTOPPULLUP_ZMIN_PROBE +#endif + +// Enable pulldown for all endstops to prevent a floating state +//#define ENDSTOPPULLDOWNS +#if DISABLED(ENDSTOPPULLDOWNS) + // Disable ENDSTOPPULLDOWNS to set pulldowns individually + //#define ENDSTOPPULLDOWN_XMAX + //#define ENDSTOPPULLDOWN_YMAX + //#define ENDSTOPPULLDOWN_ZMAX + //#define ENDSTOPPULLDOWN_XMIN + //#define ENDSTOPPULLDOWN_YMIN + //#define ENDSTOPPULLDOWN_ZMIN + //#define ENDSTOPPULLDOWN_ZMIN_PROBE +#endif + +// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup). +#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop. +#define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop. +#define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop. +#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop. +#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop. +#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop. +#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe. + +// Enable this feature if all enabled endstop pins are interrupt-capable. +// This will remove the need to poll the interrupt pins, saving many CPU cycles. +//#define ENDSTOP_INTERRUPTS_FEATURE + +//============================================================================= +//============================== Movement Settings ============================ +//============================================================================= +// @section motion + +/** + * Default Settings + * + * These settings can be reset by M502 + * + * Note that if EEPROM is enabled, saved values will override these. + */ + +/** + * With this option each E stepper can have its own factors for the + * following movement settings. If fewer factors are given than the + * total number of extruders, the last value applies to the rest. + */ +//#define DISTINCT_E_FACTORS + +/** + * Default Axis Steps Per Unit (steps/mm) + * Override with M92 + * X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]] + */ +#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 400, 93 } + +/** + * Default Max Feed Rate (mm/s) + * Override with M203 + * X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]] + */ +#define DEFAULT_MAX_FEEDRATE { 500, 500, 5, 25 } + +/** + * Default Max Acceleration (change/s) change = mm/s + * (Maximum start speed for accelerated moves) + * Override with M201 + * X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]] + */ +#define DEFAULT_MAX_ACCELERATION { 500, 500, 100, 5000 } + +/** + * Default Acceleration (change/s) change = mm/s + * Override with M204 + * + * M204 P Acceleration + * M204 R Retract Acceleration + * M204 T Travel Acceleration + */ +#define DEFAULT_ACCELERATION 500 // X, Y, Z and E acceleration for printing moves +#define DEFAULT_RETRACT_ACCELERATION 500 // E acceleration for retracts +#define DEFAULT_TRAVEL_ACCELERATION 500 // X, Y, Z acceleration for travel (non printing) moves + +/** + * Default Jerk (mm/s) + * Override with M205 X Y Z E + * + * "Jerk" specifies the minimum speed change that requires acceleration. + * When changing speed and direction, if the difference is less than the + * value set here, it may happen instantaneously. + */ +#define DEFAULT_XJERK 10.0 +#define DEFAULT_YJERK 10.0 +#define DEFAULT_ZJERK 0.3 +#define DEFAULT_EJERK 5.0 + +/** + * Realtime Jerk Control + * + * This option eliminates vibration during printing by fitting a Bézier + * curve to move acceleration, producing much smoother direction changes. + * Because this is computationally-intensive, a 32-bit MCU is required. + * + * See https://github.com/synthetos/TinyG/wiki/Jerk-Controlled-Motion-Explained + */ +//#define BEZIER_JERK_CONTROL + +//=========================================================================== +//============================= Z Probe Options ============================= +//=========================================================================== +// @section probes + +// +// See http://marlinfw.org/docs/configuration/probes.html +// + +/** + * Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN + * + * Enable this option for a probe connected to the Z Min endstop pin. + */ +#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN + +/** + * Z_MIN_PROBE_ENDSTOP + * + * Enable this option for a probe connected to any pin except Z-Min. + * (By default Marlin assumes the Z-Max endstop pin.) + * To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below. + * + * - The simplest option is to use a free endstop connector. + * - Use 5V for powered (usually inductive) sensors. + * + * - RAMPS 1.3/1.4 boards may use the 5V, GND, and Aux4->D32 pin: + * - For simple switches connect... + * - normally-closed switches to GND and D32. + * - normally-open switches to 5V and D32. + * + * WARNING: Setting the wrong pin may have unexpected and potentially + * disastrous consequences. Use with caution and do your homework. + * + */ +//#define Z_MIN_PROBE_ENDSTOP + +/** + * Probe Type + * + * Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc. + * Activate one of these to use Auto Bed Leveling below. + */ + +/** + * The "Manual Probe" provides a means to do "Auto" Bed Leveling without a probe. + * Use G29 repeatedly, adjusting the Z height at each point with movement commands + * or (with LCD_BED_LEVELING) the LCD controller. + */ +//#define PROBE_MANUALLY + +/** + * A Fix-Mounted Probe either doesn't deploy or needs manual deployment. + * (e.g., an inductive probe or a nozzle-based probe-switch.) + */ +//#define FIX_MOUNTED_PROBE + +/** + * Z Servo Probe, such as an endstop switch on a rotating arm. + */ +//#define Z_PROBE_SERVO_NR 0 // Defaults to SERVO 0 connector. +//#define Z_SERVO_ANGLES {70,0} // Z Servo Deploy and Stow angles + +/** + * The BLTouch probe uses a Hall effect sensor and emulates a servo. + */ +//#define BLTOUCH +#if ENABLED(BLTOUCH) + //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed +#endif + +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + +// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) +//#define SOLENOID_PROBE + +// A sled-mounted probe like those designed by Charles Bell. +//#define Z_PROBE_SLED +//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. + +// +// For Z_PROBE_ALLEN_KEY see the Delta example configurations. +// + +/** + * Z Probe to nozzle (X,Y) offset, relative to (0, 0). + * X and Y offsets must be integers. + * + * In the following example the X and Y offsets are both positive: + * #define X_PROBE_OFFSET_FROM_EXTRUDER 10 + * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 + * + * +-- BACK ---+ + * | | + * L | (+) P | R <-- probe (20,20) + * E | | I + * F | (-) N (+) | G <-- nozzle (10,10) + * T | | H + * | (-) | T + * | | + * O-- FRONT --+ + * (0,0) + */ +#define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle] +#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle] +#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle] + +// Certain types of probes need to stay away from edges +#define MIN_PROBE_EDGE 10 + +// X and Y axis travel speed (mm/m) between probes +#define XY_PROBE_SPEED 8000 + +// Feedrate (mm/m) for the first approach when double-probing (MULTIPLE_PROBING == 2) +#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z + +// Feedrate (mm/m) for the "accurate" probe of each point +#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2) + +// The number of probes to perform at each point. +// Set to 2 for a fast/slow probe, using the second probe result. +// Set to 3 or more for slow probes, averaging the results. +//#define MULTIPLE_PROBING 2 + +/** + * Z probes require clearance when deploying, stowing, and moving between + * probe points to avoid hitting the bed and other hardware. + * Servo-mounted probes require extra space for the arm to rotate. + * Inductive probes need space to keep from triggering early. + * + * Use these settings to specify the distance (mm) to raise the probe (or + * lower the bed). The values set here apply over and above any (negative) + * probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD. + * Only integer values >= 1 are valid here. + * + * Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle. + * But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle. + */ +#define Z_CLEARANCE_DEPLOY_PROBE 10 // Z Clearance for Deploy/Stow +#define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points +//#define Z_AFTER_PROBING 5 // Z position after probing is done + +#define Z_PROBE_LOW_POINT -2 // Farthest distance below the trigger-point to go before stopping + +// For M851 give a range for adjusting the Z probe offset +#define Z_PROBE_OFFSET_RANGE_MIN -20 +#define Z_PROBE_OFFSET_RANGE_MAX 20 + +// Enable the M48 repeatability test to test probe accuracy +//#define Z_MIN_PROBE_REPEATABILITY_TEST + +// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 +// :{ 0:'Low', 1:'High' } +#define X_ENABLE_ON 0 +#define Y_ENABLE_ON 0 +#define Z_ENABLE_ON 0 +#define E_ENABLE_ON 0 // For all extruders + +// Disables axis stepper immediately when it's not being used. +// WARNING: When motors turn off there is a chance of losing position accuracy! +#define DISABLE_X false +#define DISABLE_Y false +#define DISABLE_Z false +// Warn on display about possibly reduced accuracy +//#define DISABLE_REDUCED_ACCURACY_WARNING + +// @section extruder + +#define DISABLE_E false // For all extruders +#define DISABLE_INACTIVE_EXTRUDER false // Keep only the active extruder enabled. + +// @section machine + +// Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way. +#define INVERT_X_DIR true +#define INVERT_Y_DIR true +#define INVERT_Z_DIR false + +// Enable this option for Toshiba stepper drivers +//#define CONFIG_STEPPERS_TOSHIBA + +// @section extruder + +// For direct drive extruder v9 set to true, for geared extruder set to false. +#define INVERT_E0_DIR true +#define INVERT_E1_DIR false +#define INVERT_E2_DIR false +#define INVERT_E3_DIR false +#define INVERT_E4_DIR false + +// @section homing + +//#define NO_MOTION_BEFORE_HOMING // Inhibit movement until all axes have been homed + +//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off. + +//#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ... + // Be sure you have this distance over your Z_MAX_POS in case. + +// Direction of endstops when homing; 1=MAX, -1=MIN +// :[-1,1] +#define X_HOME_DIR -1 +#define Y_HOME_DIR -1 +#define Z_HOME_DIR -1 + +// @section machine + +// The size of the print bed +#define X_BED_SIZE 220 +#define Y_BED_SIZE 220 + +// Travel limits (mm) after homing, corresponding to endstop positions. +#define X_MIN_POS 0 +#define Y_MIN_POS 0 +#define Z_MIN_POS 0 +#define X_MAX_POS X_BED_SIZE +#define Y_MAX_POS Y_BED_SIZE +#define Z_MAX_POS 250 + +/** + * Software Endstops + * + * - Prevent moves outside the set machine bounds. + * - Individual axes can be disabled, if desired. + * - X and Y only apply to Cartesian robots. + * - Use 'M211' to set software endstops on/off or report current state + */ + +// Min software endstops constrain movement within minimum coordinate bounds +#define MIN_SOFTWARE_ENDSTOPS +#if ENABLED(MIN_SOFTWARE_ENDSTOPS) + #define MIN_SOFTWARE_ENDSTOP_X + #define MIN_SOFTWARE_ENDSTOP_Y + #define MIN_SOFTWARE_ENDSTOP_Z +#endif + +// Max software endstops constrain movement within maximum coordinate bounds +#define MAX_SOFTWARE_ENDSTOPS +#if ENABLED(MAX_SOFTWARE_ENDSTOPS) + #define MAX_SOFTWARE_ENDSTOP_X + #define MAX_SOFTWARE_ENDSTOP_Y + #define MAX_SOFTWARE_ENDSTOP_Z +#endif + +#if ENABLED(MIN_SOFTWARE_ENDSTOPS) || ENABLED(MAX_SOFTWARE_ENDSTOPS) + //#define SOFT_ENDSTOPS_MENU_ITEM // Enable/Disable software endstops from the LCD +#endif + +/** + * Filament Runout Sensors + * Mechanical or opto endstops are used to check for the presence of filament. + * + * RAMPS-based boards use SERVO3_PIN for the first runout sensor. + * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc. + * By default the firmware assumes HIGH=FILAMENT PRESENT. + */ +//#define FILAMENT_RUNOUT_SENSOR +#if ENABLED(FILAMENT_RUNOUT_SENSOR) + #define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each. + #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor. + #define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins. + //#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins. + #define FILAMENT_RUNOUT_SCRIPT "M600" +#endif + +//=========================================================================== +//=============================== Bed Leveling ============================== +//=========================================================================== +// @section calibrate + +/** + * Choose one of the options below to enable G29 Bed Leveling. The parameters + * and behavior of G29 will change depending on your selection. + * + * If using a Probe for Z Homing, enable Z_SAFE_HOMING also! + * + * - AUTO_BED_LEVELING_3POINT + * Probe 3 arbitrary points on the bed (that aren't collinear) + * You specify the XY coordinates of all 3 points. + * The result is a single tilted plane. Best for a flat bed. + * + * - AUTO_BED_LEVELING_LINEAR + * Probe several points in a grid. + * You specify the rectangle and the density of sample points. + * The result is a single tilted plane. Best for a flat bed. + * + * - AUTO_BED_LEVELING_BILINEAR + * Probe several points in a grid. + * You specify the rectangle and the density of sample points. + * The result is a mesh, best for large or uneven beds. + * + * - AUTO_BED_LEVELING_UBL (Unified Bed Leveling) + * A comprehensive bed leveling system combining the features and benefits + * of other systems. UBL also includes integrated Mesh Generation, Mesh + * Validation and Mesh Editing systems. + * + * - MESH_BED_LEVELING + * Probe a grid manually + * The result is a mesh, suitable for large or uneven beds. (See BILINEAR.) + * For machines without a probe, Mesh Bed Leveling provides a method to perform + * leveling in steps so you can manually adjust the Z height at each grid-point. + * With an LCD controller the process is guided step-by-step. + */ +//#define AUTO_BED_LEVELING_3POINT +//#define AUTO_BED_LEVELING_LINEAR +//#define AUTO_BED_LEVELING_BILINEAR +//#define AUTO_BED_LEVELING_UBL +//#define MESH_BED_LEVELING + +/** + * Normally G28 leaves leveling disabled on completion. Enable + * this option to have G28 restore the prior leveling state. + */ +//#define RESTORE_LEVELING_AFTER_G28 + +/** + * Enable detailed logging of G28, G29, M48, etc. + * Turn on with the command 'M111 S32'. + * NOTE: Requires a lot of PROGMEM! + */ +//#define DEBUG_LEVELING_FEATURE + +#if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL) + // Gradually reduce leveling correction until a set height is reached, + // at which point movement will be level to the machine's XY plane. + // The height can be set with M420 Z + #define ENABLE_LEVELING_FADE_HEIGHT + + // For Cartesian machines, instead of dividing moves on mesh boundaries, + // split up moves into short segments like a Delta. This follows the + // contours of the bed more closely than edge-to-edge straight moves. + #define SEGMENT_LEVELED_MOVES + #define LEVELED_SEGMENT_LENGTH 5.0 // (mm) Length of all segments (except the last one) + + /** + * Enable the G26 Mesh Validation Pattern tool. + */ + //#define G26_MESH_VALIDATION + #if ENABLED(G26_MESH_VALIDATION) + #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle. + #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool. + #define MESH_TEST_HOTEND_TEMP 205.0 // (°C) Default nozzle temperature for the G26 Mesh Validation Tool. + #define MESH_TEST_BED_TEMP 60.0 // (°C) Default bed temperature for the G26 Mesh Validation Tool. + #endif + +#endif + +#if ENABLED(AUTO_BED_LEVELING_LINEAR) || ENABLED(AUTO_BED_LEVELING_BILINEAR) + + // Set the number of grid points per dimension. + #define GRID_MAX_POINTS_X 3 + #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X + + // Set the boundaries for probing (where the probe can reach). + //#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE + //#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - MIN_PROBE_EDGE) + //#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE + //#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - MIN_PROBE_EDGE) + + // Probe along the Y axis, advancing X after each column + //#define PROBE_Y_FIRST + + #if ENABLED(AUTO_BED_LEVELING_BILINEAR) + + // Beyond the probed grid, continue the implied tilt? + // Default is to maintain the height of the nearest edge. + //#define EXTRAPOLATE_BEYOND_GRID + + // + // Experimental Subdivision of the grid by Catmull-Rom method. + // Synthesizes intermediate points to produce a more detailed mesh. + // + //#define ABL_BILINEAR_SUBDIVISION + #if ENABLED(ABL_BILINEAR_SUBDIVISION) + // Number of subdivisions between probe points + #define BILINEAR_SUBDIVISIONS 3 + #endif + + #endif + +#elif ENABLED(AUTO_BED_LEVELING_UBL) + + //=========================================================================== + //========================= Unified Bed Leveling ============================ + //=========================================================================== + + //#define MESH_EDIT_GFX_OVERLAY // Display a graphics overlay while editing the mesh + + #define MESH_INSET 1 // Set Mesh bounds as an inset region of the bed + #define GRID_MAX_POINTS_X 10 // Don't use more than 15 points per axis, implementation limited. + #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X + + #define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle + #define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500 + + //#define UBL_Z_RAISE_WHEN_OFF_MESH 2.5 // When the nozzle is off the mesh, this value is used + // as the Z-Height correction value. + +#elif ENABLED(MESH_BED_LEVELING) + + //=========================================================================== + //=================================== Mesh ================================== + //=========================================================================== + + #define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed + #define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited. + #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X + + //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS + +#endif // BED_LEVELING + +/** + * Points to probe for all 3-point Leveling procedures. + * Override if the automatically selected points are inadequate. + */ +#if ENABLED(AUTO_BED_LEVELING_3POINT) || ENABLED(AUTO_BED_LEVELING_UBL) + //#define PROBE_PT_1_X 15 + //#define PROBE_PT_1_Y 180 + //#define PROBE_PT_2_X 15 + //#define PROBE_PT_2_Y 20 + //#define PROBE_PT_3_X 170 + //#define PROBE_PT_3_Y 20 +#endif + +/** + * Use the LCD controller for bed leveling + * Requires MESH_BED_LEVELING or PROBE_MANUALLY + */ +//#define LCD_BED_LEVELING + +#if ENABLED(LCD_BED_LEVELING) + #define MBL_Z_STEP 0.025 // Step size while manually probing Z axis. + #define LCD_PROBE_Z_RANGE 4 // Z Range centered on Z_MIN_POS for LCD Z adjustment +#endif + +// Add a menu item to move between bed corners for manual bed adjustment +//#define LEVEL_BED_CORNERS + +#if ENABLED(LEVEL_BED_CORNERS) + #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling + //#define LEVEL_CENTER_TOO // Move to the center after the last corner +#endif + +/** + * Commands to execute at the end of G29 probing. + * Useful to retract or move the Z probe out of the way. + */ +//#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" + + +// @section homing + +// The center of the bed is at (X=0, Y=0) +//#define BED_CENTER_AT_0_0 + +// Manually set the home position. Leave these undefined for automatic settings. +// For DELTA this is the top-center of the Cartesian print volume. +//#define MANUAL_X_HOME_POS 0 +//#define MANUAL_Y_HOME_POS 0 +//#define MANUAL_Z_HOME_POS 0 + +// Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area. +// +// With this feature enabled: +// +// - Allow Z homing only after X and Y homing AND stepper drivers still enabled. +// - If stepper drivers time out, it will need X and Y homing again before Z homing. +// - Move the Z probe (or nozzle) to a defined XY point before Z Homing when homing all axes (G28). +// - Prevent Z homing when the Z probe is outside bed area. +// +//#define Z_SAFE_HOMING + +#if ENABLED(Z_SAFE_HOMING) + #define Z_SAFE_HOMING_X_POINT ((X_BED_SIZE) / 2) // X point for Z homing when homing all axes (G28). + #define Z_SAFE_HOMING_Y_POINT ((Y_BED_SIZE) / 2) // Y point for Z homing when homing all axes (G28). +#endif + +// Homing speeds (mm/m) +#define HOMING_FEEDRATE_XY (50*60) +#define HOMING_FEEDRATE_Z (4*60) + +// @section calibrate + +/** + * Bed Skew Compensation + * + * This feature corrects for misalignment in the XYZ axes. + * + * Take the following steps to get the bed skew in the XY plane: + * 1. Print a test square (e.g., https://www.thingiverse.com/thing:2563185) + * 2. For XY_DIAG_AC measure the diagonal A to C + * 3. For XY_DIAG_BD measure the diagonal B to D + * 4. For XY_SIDE_AD measure the edge A to D + * + * Marlin automatically computes skew factors from these measurements. + * Skew factors may also be computed and set manually: + * + * - Compute AB : SQRT(2*AC*AC+2*BD*BD-4*AD*AD)/2 + * - XY_SKEW_FACTOR : TAN(PI/2-ACOS((AC*AC-AB*AB-AD*AD)/(2*AB*AD))) + * + * If desired, follow the same procedure for XZ and YZ. + * Use these diagrams for reference: + * + * Y Z Z + * ^ B-------C ^ B-------C ^ B-------C + * | / / | / / | / / + * | / / | / / | / / + * | A-------D | A-------D | A-------D + * +-------------->X +-------------->X +-------------->Y + * XY_SKEW_FACTOR XZ_SKEW_FACTOR YZ_SKEW_FACTOR + */ +//#define SKEW_CORRECTION + +#if ENABLED(SKEW_CORRECTION) + // Input all length measurements here: + #define XY_DIAG_AC 282.8427124746 + #define XY_DIAG_BD 282.8427124746 + #define XY_SIDE_AD 200 + + // Or, set the default skew factors directly here + // to override the above measurements: + #define XY_SKEW_FACTOR 0.0 + + //#define SKEW_CORRECTION_FOR_Z + #if ENABLED(SKEW_CORRECTION_FOR_Z) + #define XZ_DIAG_AC 282.8427124746 + #define XZ_DIAG_BD 282.8427124746 + #define YZ_DIAG_AC 282.8427124746 + #define YZ_DIAG_BD 282.8427124746 + #define YZ_SIDE_AD 200 + #define XZ_SKEW_FACTOR 0.0 + #define YZ_SKEW_FACTOR 0.0 + #endif + + // Enable this option for M852 to set skew at runtime + //#define SKEW_CORRECTION_GCODE +#endif + +//============================================================================= +//============================= Additional Features =========================== +//============================================================================= + +// @section extras + +// +// EEPROM +// +// The microcontroller can store settings in the EEPROM, e.g. max velocity... +// M500 - stores parameters in EEPROM +// M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily). +// M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to. +// +#define EEPROM_SETTINGS // Enable for M500 and M501 commands +//#define DISABLE_M503 // Saves ~2700 bytes of PROGMEM. Disable for release! +#define EEPROM_CHITCHAT // Give feedback on EEPROM commands. Disable to save PROGMEM. + +// +// Host Keepalive +// +// When enabled Marlin will send a busy status message to the host +// every couple of seconds when it can't accept commands. +// +#define HOST_KEEPALIVE_FEATURE // Disable this if your host doesn't like keepalive messages +#define DEFAULT_KEEPALIVE_INTERVAL 2 // Number of seconds between "busy" messages. Set with M113. +#define BUSY_WHILE_HEATING // Some hosts require "busy" messages even during heating + +// +// M100 Free Memory Watcher +// +//#define M100_FREE_MEMORY_WATCHER // Add M100 (Free Memory Watcher) to debug memory usage + +// +// G20/G21 Inch mode support +// +//#define INCH_MODE_SUPPORT + +// +// M149 Set temperature units support +// +//#define TEMPERATURE_UNITS_SUPPORT + +// @section temperature + +// Preheat Constants +#define PREHEAT_1_TEMP_HOTEND 185 +#define PREHEAT_1_TEMP_BED 45 +#define PREHEAT_1_FAN_SPEED 255 // Value from 0 to 255 + +#define PREHEAT_2_TEMP_HOTEND 240 +#define PREHEAT_2_TEMP_BED 0 +#define PREHEAT_2_FAN_SPEED 255 // Value from 0 to 255 + +/** + * Nozzle Park + * + * Park the nozzle at the given XYZ position on idle or G27. + * + * The "P" parameter controls the action applied to the Z axis: + * + * P0 (Default) If Z is below park Z raise the nozzle. + * P1 Raise the nozzle always to Z-park height. + * P2 Raise the nozzle by Z-park amount, limited to Z_MAX_POS. + */ +//#define NOZZLE_PARK_FEATURE + +#if ENABLED(NOZZLE_PARK_FEATURE) + // Specify a park position as { X, Y, Z } + #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 } + #define NOZZLE_PARK_XY_FEEDRATE 100 // X and Y axes feedrate in mm/s (also used for delta printers Z axis) + #define NOZZLE_PARK_Z_FEEDRATE 5 // Z axis feedrate in mm/s (not used for delta printers) +#endif + +/** + * Clean Nozzle Feature -- EXPERIMENTAL + * + * Adds the G12 command to perform a nozzle cleaning process. + * + * Parameters: + * P Pattern + * S Strokes / Repetitions + * T Triangles (P1 only) + * + * Patterns: + * P0 Straight line (default). This process requires a sponge type material + * at a fixed bed location. "S" specifies strokes (i.e. back-forth motions) + * between the start / end points. + * + * P1 Zig-zag pattern between (X0, Y0) and (X1, Y1), "T" specifies the + * number of zig-zag triangles to do. "S" defines the number of strokes. + * Zig-zags are done in whichever is the narrower dimension. + * For example, "G12 P1 S1 T3" will execute: + * + * -- + * | (X0, Y1) | /\ /\ /\ | (X1, Y1) + * | | / \ / \ / \ | + * A | | / \ / \ / \ | + * | | / \ / \ / \ | + * | (X0, Y0) | / \/ \/ \ | (X1, Y0) + * -- +--------------------------------+ + * |________|_________|_________| + * T1 T2 T3 + * + * P2 Circular pattern with middle at NOZZLE_CLEAN_CIRCLE_MIDDLE. + * "R" specifies the radius. "S" specifies the stroke count. + * Before starting, the nozzle moves to NOZZLE_CLEAN_START_POINT. + * + * Caveats: The ending Z should be the same as starting Z. + * Attention: EXPERIMENTAL. G-code arguments may change. + * + */ +//#define NOZZLE_CLEAN_FEATURE + +#if ENABLED(NOZZLE_CLEAN_FEATURE) + // Default number of pattern repetitions + #define NOZZLE_CLEAN_STROKES 12 + + // Default number of triangles + #define NOZZLE_CLEAN_TRIANGLES 3 + + // Specify positions as { X, Y, Z } + #define NOZZLE_CLEAN_START_POINT { 30, 30, (Z_MIN_POS + 1)} + #define NOZZLE_CLEAN_END_POINT {100, 60, (Z_MIN_POS + 1)} + + // Circular pattern radius + #define NOZZLE_CLEAN_CIRCLE_RADIUS 6.5 + // Circular pattern circle fragments number + #define NOZZLE_CLEAN_CIRCLE_FN 10 + // Middle point of circle + #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT + + // Moves the nozzle to the initial position + #define NOZZLE_CLEAN_GOBACK +#endif + +/** + * Print Job Timer + * + * Automatically start and stop the print job timer on M104/M109/M190. + * + * M104 (hotend, no wait) - high temp = none, low temp = stop timer + * M109 (hotend, wait) - high temp = start timer, low temp = stop timer + * M190 (bed, wait) - high temp = start timer, low temp = none + * + * The timer can also be controlled with the following commands: + * + * M75 - Start the print job timer + * M76 - Pause the print job timer + * M77 - Stop the print job timer + */ +#define PRINTJOB_TIMER_AUTOSTART + +/** + * Print Counter + * + * Track statistical data such as: + * + * - Total print jobs + * - Total successful print jobs + * - Total failed print jobs + * - Total time printing + * + * View the current statistics with M78. + */ +//#define PRINTCOUNTER + +//============================================================================= +//============================= LCD and SD support ============================ +//============================================================================= + +// @section lcd + +/** + * LCD LANGUAGE + * + * Select the language to display on the LCD. These languages are available: + * + * en, an, bg, ca, cn, cz, de, el, el-gr, es, eu, fi, fr, + * gl, hr, it, jp-kana, nl, pl, pt, pt-br, ru, sk, + * tr, uk, zh_CN, zh_TW, test + * + * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'jp-kana':'Japanese', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'ru':'Russian', 'sk':'Slovak', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Traditional)', test':'TEST' } + */ +#define LCD_LANGUAGE en + +/** + * LCD Character Set + * + * Note: This option is NOT applicable to Graphical Displays. + * + * All character-based LCDs provide ASCII plus one of these + * language extensions: + * + * - JAPANESE ... the most common + * - WESTERN ... with more accented characters + * - CYRILLIC ... for the Russian language + * + * To determine the language extension installed on your controller: + * + * - Compile and upload with LCD_LANGUAGE set to 'test' + * - Click the controller to view the LCD menu + * - The LCD will display Japanese, Western, or Cyrillic text + * + * See http://marlinfw.org/docs/development/lcd_language.html + * + * :['JAPANESE', 'WESTERN', 'CYRILLIC'] + */ +#define DISPLAY_CHARSET_HD44780 WESTERN + +/** + * LCD TYPE + * + * Enable ULTRA_LCD for a 16x2, 16x4, 20x2, or 20x4 character-based LCD. + * Enable DOGLCD for a 128x64 (ST7565R) Full Graphical Display. + * (These options will be enabled automatically for most displays.) + * + * IMPORTANT: The U8glib library is required for Full Graphic Display! + * https://github.com/olikraus/U8glib_Arduino + */ +//#define ULTRA_LCD // Character based +//#define DOGLCD // Full graphics display + +/** + * SD CARD + * + * SD Card support is disabled by default. If your controller has an SD slot, + * you must uncomment the following option or it won't work. + * + */ +#define SDSUPPORT + +/** + * SD CARD: SPI SPEED + * + * Enable one of the following items for a slower SPI transfer speed. + * This may be required to resolve "volume init" errors. + */ +//#define SPI_SPEED SPI_HALF_SPEED +//#define SPI_SPEED SPI_QUARTER_SPEED +//#define SPI_SPEED SPI_EIGHTH_SPEED + +/** + * SD CARD: ENABLE CRC + * + * Use CRC checks and retries on the SD communication. + */ +//#define SD_CHECK_AND_RETRY + +/** + * LCD Menu Items + * + * Disable all menus and only display the Status Screen, or + * just remove some extraneous menu items to recover space. + */ +//#define NO_LCD_MENUS +//#define SLIM_LCD_MENUS + +// +// ENCODER SETTINGS +// +// This option overrides the default number of encoder pulses needed to +// produce one step. Should be increased for high-resolution encoders. +// +//#define ENCODER_PULSES_PER_STEP 4 + +// +// Use this option to override the number of step signals required to +// move between next/prev menu items. +// +//#define ENCODER_STEPS_PER_MENU_ITEM 1 + +/** + * Encoder Direction Options + * + * Test your encoder's behavior first with both options disabled. + * + * Reversed Value Edit and Menu Nav? Enable REVERSE_ENCODER_DIRECTION. + * Reversed Menu Navigation only? Enable REVERSE_MENU_DIRECTION. + * Reversed Value Editing only? Enable BOTH options. + */ + +// +// This option reverses the encoder direction everywhere. +// +// Set this option if CLOCKWISE causes values to DECREASE +// +//#define REVERSE_ENCODER_DIRECTION + +// +// This option reverses the encoder direction for navigating LCD menus. +// +// If CLOCKWISE normally moves DOWN this makes it go UP. +// If CLOCKWISE normally moves UP this makes it go DOWN. +// +//#define REVERSE_MENU_DIRECTION + +// +// Individual Axis Homing +// +// Add individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu. +// +//#define INDIVIDUAL_AXIS_HOMING_MENU + +// +// SPEAKER/BUZZER +// +// If you have a speaker that can produce tones, enable it here. +// By default Marlin assumes you have a buzzer with a fixed frequency. +// +#define SPEAKER + +// +// The duration and frequency for the UI feedback sound. +// Set these to 0 to disable audio feedback in the LCD menus. +// +// Note: Test audio output with the G-Code: +// M300 S P +// +//#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 2 +//#define LCD_FEEDBACK_FREQUENCY_HZ 5000 + +// +// CONTROLLER TYPE: Standard +// +// Marlin supports a wide variety of controllers. +// Enable one of the following options to specify your controller. +// + +// +// Original RADDS LCD Display+Encoder+SDCardReader +// http://doku.radds.org/dokumentation/lcd-display/ +// +//#define RADDS_DISPLAY + +// +// ULTIMAKER Controller. +// +//#define ULTIMAKERCONTROLLER + +// +// ULTIPANEL as seen on Thingiverse. +// +//#define ULTIPANEL + +// +// PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3) +// http://reprap.org/wiki/PanelOne +// +//#define PANEL_ONE + +// +// MaKr3d Makr-Panel with graphic controller and SD support. +// http://reprap.org/wiki/MaKr3d_MaKrPanel +// +//#define MAKRPANEL + +// +// ReprapWorld Graphical LCD +// https://reprapworld.com/?products_details&products_id/1218 +// +//#define REPRAPWORLD_GRAPHICAL_LCD + +// +// Activate one of these if you have a Panucatt Devices +// Viki 2.0 or mini Viki with Graphic LCD +// http://panucatt.com +// +//#define VIKI2 +//#define miniVIKI + +// +// Adafruit ST7565 Full Graphic Controller. +// https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/ +// +//#define ELB_FULL_GRAPHIC_CONTROLLER + +// +// RepRapDiscount Smart Controller. +// http://reprap.org/wiki/RepRapDiscount_Smart_Controller +// +// Note: Usually sold with a white PCB. +// +//#define REPRAP_DISCOUNT_SMART_CONTROLLER + +// +// GADGETS3D G3D LCD/SD Controller +// http://reprap.org/wiki/RAMPS_1.3/1.4_GADGETS3D_Shield_with_Panel +// +// Note: Usually sold with a blue PCB. +// +//#define G3D_PANEL + +// +// RepRapDiscount FULL GRAPHIC Smart Controller +// http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller +// +//#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER + +// +// MakerLab Mini Panel with graphic +// controller and SD support - http://reprap.org/wiki/Mini_panel +// +//#define MINIPANEL + +// +// RepRapWorld REPRAPWORLD_KEYPAD v1.1 +// http://reprapworld.com/?products_details&products_id=202&cPath=1591_1626 +// +// REPRAPWORLD_KEYPAD_MOVE_STEP sets how much should the robot move when a key +// is pressed, a value of 10.0 means 10mm per click. +// +//#define REPRAPWORLD_KEYPAD +//#define REPRAPWORLD_KEYPAD_MOVE_STEP 1.0 + +// +// RigidBot Panel V1.0 +// http://www.inventapart.com/ +// +//#define RIGIDBOT_PANEL + +// +// BQ LCD Smart Controller shipped by +// default with the BQ Hephestos 2 and Witbox 2. +// +//#define BQ_LCD_SMART_CONTROLLER + +// +// Cartesio UI +// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface +// +//#define CARTESIO_UI + +// +// ANET and Tronxy Controller supported displays. +// +//#define ZONESTAR_LCD // Requires ADC_KEYPAD_PIN to be assigned to an analog pin. + // This LCD is known to be susceptible to electrical interference + // which scrambles the display. Pressing any button clears it up. + // This is a LCD2004 display with 5 analog buttons. + +//#define ANET_FULL_GRAPHICS_LCD // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6 + // A clone of the RepRapDiscount full graphics display but with + // different pins/wiring (see pins_ANET_10.h). + +// +// LCD for Melzi Card with Graphical LCD +// +//#define LCD_FOR_MELZI + +// +// LCD for Malyan M200 printers. +// This requires SDSUPPORT to be enabled +// +//#define MALYAN_LCD + +// +// CONTROLLER TYPE: I2C +// +// Note: These controllers require the installation of Arduino's LiquidCrystal_I2C +// library. For more info: https://github.com/kiyoshigawa/LiquidCrystal_I2C +// + +// +// Elefu RA Board Control Panel +// http://www.elefu.com/index.php?route=product/product&product_id=53 +// +//#define RA_CONTROL_PANEL + +// +// Sainsmart (YwRobot) LCD Displays +// +// These require F.Malpartida's LiquidCrystal_I2C library +// https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/Home +// +//#define LCD_SAINSMART_I2C_1602 +//#define LCD_SAINSMART_I2C_2004 + +// +// Generic LCM1602 LCD adapter +// +//#define LCM1602 + +// +// PANELOLU2 LCD with status LEDs, +// separate encoder and click inputs. +// +// Note: This controller requires Arduino's LiquidTWI2 library v1.2.3 or later. +// For more info: https://github.com/lincomatic/LiquidTWI2 +// +// Note: The PANELOLU2 encoder click input can either be directly connected to +// a pin (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1). +// +//#define LCD_I2C_PANELOLU2 + +// +// Panucatt VIKI LCD with status LEDs, +// integrated click & L/R/U/D buttons, separate encoder inputs. +// +//#define LCD_I2C_VIKI + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + //#define U8GLIB_SSD1306 + #define U8GLIB_SH1106 +#endif + +// +// Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder +// https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) +// +//#define ULTI_CONTROLLER + +// +// CONTROLLER TYPE: Shift register panels +// +// 2 wire Non-latching LCD SR from https://goo.gl/aJJ4sH +// LCD configuration: http://reprap.org/wiki/SAV_3D_LCD +// +//#define SAV_3DLCD + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller +// https://www.aliexpress.com/item/Micromake-Makeboard-3D-Printer-Parts-3D-Printer-Mini-Display-1602-Mini-Controller-Compatible-with-Ramps-1/32765887917.html +// +//#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602 + +// +// MKS MINI12864 with graphic controller and SD support +// http://reprap.org/wiki/MKS_MINI_12864 +// +//#define MKS_MINI_12864 + +// +// Factory display for Creality CR-10 +// https://www.aliexpress.com/item/Universal-LCD-12864-3D-Printer-Display-Screen-With-Encoder-For-CR-10-CR-7-Model/32833148327.html +// +// This is RAMPS-compatible using a single 10-pin connector. +// (For CR-10 owners who want to replace the Melzi Creality board but retain the display) +// +#define CR10_STOCKDISPLAY + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// AZSMZ 12864 LCD with SD +// https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html +// +//#define AZSMZ_12864 + +// +// Silvergate GLCD controller +// http://github.com/android444/Silvergate +// +//#define SILVER_GATE_GLCD_CONTROLLER + +//============================================================================= +//=============================== Extra Features ============================== +//============================================================================= + +// @section extras + +// Increase the FAN PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino +//#define FAST_PWM_FAN + +// Use software PWM to drive the fan, as for the heaters. This uses a very low frequency +// which is not as annoying as with the hardware PWM. On the other hand, if this frequency +// is too low, you should also increment SOFT_PWM_SCALE. +//#define FAN_SOFT_PWM + +// Incrementing this by 1 will double the software PWM frequency, +// affecting heaters, and the fan if FAN_SOFT_PWM is enabled. +// However, control resolution will be halved for each increment; +// at zero value, there are 128 effective control positions. +#define SOFT_PWM_SCALE 0 + +// If SOFT_PWM_SCALE is set to a value higher than 0, dithering can +// be used to mitigate the associated resolution loss. If enabled, +// some of the PWM cycles are stretched so on average the desired +// duty cycle is attained. +//#define SOFT_PWM_DITHER + +// Temperature status LEDs that display the hotend and bed temperature. +// If all hotends, bed temperature, and target temperature are under 54C +// then the BLUE led is on. Otherwise the RED led is on. (1C hysteresis) +//#define TEMP_STAT_LEDS + +// M240 Triggers a camera by emulating a Canon RC-1 Remote +// Data from: http://www.doc-diy.net/photo/rc-1_hacked/ +//#define PHOTOGRAPH_PIN 23 + +// SkeinForge sends the wrong arc g-codes when using Arc Point as fillet procedure +//#define SF_ARC_FIX + +// Support for the BariCUDA Paste Extruder +//#define BARICUDA + +// Support for BlinkM/CyzRgb +//#define BLINKM + +// Support for PCA9632 PWM LED driver +//#define PCA9632 + +/** + * RGB LED / LED Strip Control + * + * Enable support for an RGB LED connected to 5V digital pins, or + * an RGB Strip connected to MOSFETs controlled by digital pins. + * + * Adds the M150 command to set the LED (or LED strip) color. + * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of + * luminance values can be set from 0 to 255. + * For Neopixel LED an overall brightness parameter is also available. + * + * *** CAUTION *** + * LED Strips require a MOFSET Chip between PWM lines and LEDs, + * as the Arduino cannot handle the current the LEDs will require. + * Failure to follow this precaution can destroy your Arduino! + * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * more current than the Arduino 5V linear regulator can produce. + * *** CAUTION *** + * + * LED Type. Enable only one of the following two options. + * + */ +//#define RGB_LED +//#define RGBW_LED + +#if ENABLED(RGB_LED) || ENABLED(RGBW_LED) + #define RGB_LED_R_PIN 34 + #define RGB_LED_G_PIN 43 + #define RGB_LED_B_PIN 35 + #define RGB_LED_W_PIN -1 +#endif + +// Support for Adafruit Neopixel LED driver +//#define NEOPIXEL_LED +#if ENABLED(NEOPIXEL_LED) + #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) + #define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba) + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. + #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) + //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup +#endif + +/** + * Printer Event LEDs + * + * During printing, the LEDs will reflect the printer status: + * + * - Gradually change from blue to violet as the heated bed gets to target temp + * - Gradually change from violet to red as the hotend gets to temperature + * - Change to white to illuminate work surface + * - Change to green once print has finished + * - Turn off after the print has finished and the user has pushed a button + */ +#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED) + #define PRINTER_EVENT_LEDS +#endif + +/** + * R/C SERVO support + * Sponsored by TrinityLabs, Reworked by codexmas + */ + +/** + * Number of servos + * + * For some servo-related options NUM_SERVOS will be set automatically. + * Set this manually if there are extra servos needing manual control. + * Leave undefined or set to 0 to entirely disable the servo subsystem. + */ +//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command + +// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle. +// 300ms is a good value but you can try less delay. +// If the servo can't reach the requested position, increase it. +#define SERVO_DELAY { 300 } + +// Servo deactivation +// +// With this option servos are powered only during movement, then turned off to prevent jitter. +//#define DEACTIVATE_SERVOS_AFTER_MOVE + +#endif // CONFIGURATION_H diff --git a/Marlin/src/config/examples/Creality/Ender-3/Configuration_adv.h b/Marlin/src/config/examples/Creality/Ender-3/Configuration_adv.h new file mode 100644 index 0000000000..6b7b581d63 --- /dev/null +++ b/Marlin/src/config/examples/Creality/Ender-3/Configuration_adv.h @@ -0,0 +1,1657 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ + +/** + * Configuration_adv.h + * + * Advanced settings. + * Only change these if you know exactly what you're doing. + * Some of these settings can damage your printer if improperly set! + * + * Basic settings can be found in Configuration.h + * + */ +#ifndef CONFIGURATION_ADV_H +#define CONFIGURATION_ADV_H +#define CONFIGURATION_ADV_H_VERSION 020000 + +// @section temperature + +//=========================================================================== +//=============================Thermal Settings ============================ +//=========================================================================== + +// +// Hephestos 2 24V heated bed upgrade kit. +// https://store.bq.com/en/heated-bed-kit-hephestos2 +// +//#define HEPHESTOS2_HEATED_BED_KIT +#if ENABLED(HEPHESTOS2_HEATED_BED_KIT) + #undef TEMP_SENSOR_BED + #define TEMP_SENSOR_BED 70 + #define HEATER_BED_INVERTING true +#endif + +#if DISABLED(PIDTEMPBED) + #define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control + #if ENABLED(BED_LIMIT_SWITCHING) + #define BED_HYSTERESIS 2 // Only disable heating if T>target+BED_HYSTERESIS and enable heating if T>target-BED_HYSTERESIS + #endif +#endif + +/** + * Thermal Protection provides additional protection to your printer from damage + * and fire. Marlin always includes safe min and max temperature ranges which + * protect against a broken or disconnected thermistor wire. + * + * The issue: If a thermistor falls out, it will report the much lower + * temperature of the air in the room, and the the firmware will keep + * the heater on. + * + * The solution: Once the temperature reaches the target, start observing. + * If the temperature stays too far below the target (hysteresis) for too + * long (period), the firmware will halt the machine as a safety precaution. + * + * If you get false positives for "Thermal Runaway", increase + * THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD + */ +#if ENABLED(THERMAL_PROTECTION_HOTENDS) + #define THERMAL_PROTECTION_PERIOD 40 // Seconds + #define THERMAL_PROTECTION_HYSTERESIS 4 // Degrees Celsius + + /** + * Whenever an M104, M109, or M303 increases the target temperature, the + * firmware will wait for the WATCH_TEMP_PERIOD to expire. If the temperature + * hasn't increased by WATCH_TEMP_INCREASE degrees, the machine is halted and + * requires a hard reset. This test restarts with any M104/M109/M303, but only + * if the current temperature is far enough below the target for a reliable + * test. + * + * If you get false positives for "Heating failed", increase WATCH_TEMP_PERIOD + * and/or decrease WATCH_TEMP_INCREASE. WATCH_TEMP_INCREASE should not be set + * below 2. + */ + #define WATCH_TEMP_PERIOD 20 // Seconds + #define WATCH_TEMP_INCREASE 2 // Degrees Celsius +#endif + +/** + * Thermal Protection parameters for the bed are just as above for hotends. + */ +#if ENABLED(THERMAL_PROTECTION_BED) + #define THERMAL_PROTECTION_BED_PERIOD 20 // Seconds + #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius + + /** + * As described above, except for the bed (M140/M190/M303). + */ + #define WATCH_BED_TEMP_PERIOD 60 // Seconds + #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius +#endif + +#if ENABLED(PIDTEMP) + // this adds an experimental additional term to the heating power, proportional to the extrusion speed. + // if Kc is chosen well, the additional required power due to increased melting should be compensated. + //#define PID_EXTRUSION_SCALING + #if ENABLED(PID_EXTRUSION_SCALING) + #define DEFAULT_Kc (100) //heating power=Kc*(e_speed) + #define LPQ_MAX_LEN 50 + #endif +#endif + +/** + * Automatic Temperature: + * The hotend target temperature is calculated by all the buffered lines of gcode. + * The maximum buffered steps/sec of the extruder motor is called "se". + * Start autotemp mode with M109 S B F + * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by + * mintemp and maxtemp. Turn this off by executing M109 without F* + * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp. + * On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode + */ +#define AUTOTEMP +#if ENABLED(AUTOTEMP) + #define AUTOTEMP_OLDWEIGHT 0.98 +#endif + +// Show extra position information in M114 +//#define M114_DETAIL + +// Show Temperature ADC value +// Enable for M105 to include ADC values read from temperature sensors. +//#define SHOW_TEMP_ADC_VALUES + +/** + * High Temperature Thermistor Support + * + * Thermistors able to support high temperature tend to have a hard time getting + * good readings at room and lower temperatures. This means HEATER_X_RAW_LO_TEMP + * will probably be caught when the heating element first turns on during the + * preheating process, which will trigger a min_temp_error as a safety measure + * and force stop everything. + * To circumvent this limitation, we allow for a preheat time (during which, + * min_temp_error won't be triggered) and add a min_temp buffer to handle + * aberrant readings. + * + * If you want to enable this feature for your hotend thermistor(s) + * uncomment and set values > 0 in the constants below + */ + +// The number of consecutive low temperature errors that can occur +// before a min_temp_error is triggered. (Shouldn't be more than 10.) +//#define MAX_CONSECUTIVE_LOW_TEMPERATURE_ERROR_ALLOWED 0 + +// The number of milliseconds a hotend will preheat before starting to check +// the temperature. This value should NOT be set to the time it takes the +// hot end to reach the target temperature, but the time it takes to reach +// the minimum temperature your thermistor can read. The lower the better/safer. +// This shouldn't need to be more than 30 seconds (30000) +//#define MILLISECONDS_PREHEAT_TIME 0 + +// @section extruder + +// Extruder runout prevention. +// If the machine is idle and the temperature over MINTEMP +// then extrude some filament every couple of SECONDS. +//#define EXTRUDER_RUNOUT_PREVENT +#if ENABLED(EXTRUDER_RUNOUT_PREVENT) + #define EXTRUDER_RUNOUT_MINTEMP 190 + #define EXTRUDER_RUNOUT_SECONDS 30 + #define EXTRUDER_RUNOUT_SPEED 1500 // mm/m + #define EXTRUDER_RUNOUT_EXTRUDE 5 // mm +#endif + +// @section temperature + +//These defines help to calibrate the AD595 sensor in case you get wrong temperature measurements. +//The measured temperature is defined as "actualTemp = (measuredTemp * TEMP_SENSOR_AD595_GAIN) + TEMP_SENSOR_AD595_OFFSET" +#define TEMP_SENSOR_AD595_OFFSET 0.0 +#define TEMP_SENSOR_AD595_GAIN 1.0 + +/** + * Controller Fan + * To cool down the stepper drivers and MOSFETs. + * + * The fan will turn on automatically whenever any stepper is enabled + * and turn off after a set period after all steppers are turned off. + */ +//#define USE_CONTROLLER_FAN +#if ENABLED(USE_CONTROLLER_FAN) + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled + #define CONTROLLERFAN_SPEED 255 // 255 == full speed +#endif + +// When first starting the main fan, run it at full speed for the +// given number of milliseconds. This gets the fan spinning reliably +// before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu) +//#define FAN_KICKSTART_TIME 100 + +// This defines the minimal speed for the main fan, run in PWM mode +// to enable uncomment and set minimal PWM speed for reliable running (1-255) +// if fan speed is [1 - (FAN_MIN_PWM-1)] it is set to FAN_MIN_PWM +//#define FAN_MIN_PWM 50 + +// @section extruder + +/** + * Extruder cooling fans + * + * Extruder auto fans automatically turn on when their extruders' + * temperatures go above EXTRUDER_AUTO_FAN_TEMPERATURE. + * + * Your board's pins file specifies the recommended pins. Override those here + * or set to -1 to disable completely. + * + * Multiple extruders can be assigned to the same pin in which case + * the fan will turn on when any selected extruder is above the threshold. + */ +#define E0_AUTO_FAN_PIN -1 +#define E1_AUTO_FAN_PIN -1 +#define E2_AUTO_FAN_PIN -1 +#define E3_AUTO_FAN_PIN -1 +#define E4_AUTO_FAN_PIN -1 +#define CHAMBER_AUTO_FAN_PIN -1 +#define EXTRUDER_AUTO_FAN_TEMPERATURE 50 +#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed + +/** + * Part-Cooling Fan Multiplexer + * + * This feature allows you to digitally multiplex the fan output. + * The multiplexer is automatically switched at tool-change. + * Set FANMUX[012]_PINs below for up to 2, 4, or 8 multiplexed fans. + */ +#define FANMUX0_PIN -1 +#define FANMUX1_PIN -1 +#define FANMUX2_PIN -1 + +/** + * M355 Case Light on-off / brightness + */ +//#define CASE_LIGHT_ENABLE +#if ENABLED(CASE_LIGHT_ENABLE) + //#define CASE_LIGHT_PIN 4 // Override the default pin if needed + #define INVERT_CASE_LIGHT false // Set true if Case Light is ON when pin is LOW + #define CASE_LIGHT_DEFAULT_ON true // Set default power-up state on + #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105 // Set default power-up brightness (0-255, requires PWM pin) + //#define MENU_ITEM_CASE_LIGHT // Add a Case Light option to the LCD main menu + //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) + #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } + #endif +#endif + +//=========================================================================== +//============================ Mechanical Settings ========================== +//=========================================================================== + +// @section homing + +// If you want endstops to stay on (by default) even when not homing +// enable this option. Override at any time with M120, M121. +//#define ENDSTOPS_ALWAYS_ON_DEFAULT + +// @section extras + +//#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats. + +/** + * Dual Steppers / Dual Endstops + * + * This section will allow you to use extra E drivers to drive a second motor for X, Y, or Z axes. + * + * For example, set X_DUAL_STEPPER_DRIVERS setting to use a second motor. If the motors need to + * spin in opposite directions set INVERT_X2_VS_X_DIR. If the second motor needs its own endstop + * set X_DUAL_ENDSTOPS. This can adjust for "racking." Use X2_USE_ENDSTOP to set the endstop plug + * that should be used for the second endstop. Extra endstops will appear in the output of 'M119'. + * + * Use X_DUAL_ENDSTOP_ADJUSTMENT to adjust for mechanical imperfection. After homing both motors + * this offset is applied to the X2 motor. To find the offset home the X axis, and measure the error + * in X2. Dual endstop offsets can be set at runtime with 'M666 X Y Z'. + */ + +//#define X_DUAL_STEPPER_DRIVERS +#if ENABLED(X_DUAL_STEPPER_DRIVERS) + #define INVERT_X2_VS_X_DIR true // Set 'true' if X motors should rotate in opposite directions + //#define X_DUAL_ENDSTOPS + #if ENABLED(X_DUAL_ENDSTOPS) + #define X2_USE_ENDSTOP _XMAX_ + #define X_DUAL_ENDSTOPS_ADJUSTMENT 0 + #endif +#endif + +//#define Y_DUAL_STEPPER_DRIVERS +#if ENABLED(Y_DUAL_STEPPER_DRIVERS) + #define INVERT_Y2_VS_Y_DIR true // Set 'true' if Y motors should rotate in opposite directions + //#define Y_DUAL_ENDSTOPS + #if ENABLED(Y_DUAL_ENDSTOPS) + #define Y2_USE_ENDSTOP _YMAX_ + #define Y_DUAL_ENDSTOPS_ADJUSTMENT 0 + #endif +#endif + +//#define Z_DUAL_STEPPER_DRIVERS +#if ENABLED(Z_DUAL_STEPPER_DRIVERS) + //#define Z_DUAL_ENDSTOPS + #if ENABLED(Z_DUAL_ENDSTOPS) + #define Z2_USE_ENDSTOP _XMAX_ + #define Z_DUAL_ENDSTOPS_ADJUSTMENT 0 + #endif +#endif + +// Enable this for dual x-carriage printers. +// A dual x-carriage design has the advantage that the inactive extruder can be parked which +// prevents hot-end ooze contaminating the print. It also reduces the weight of each x-carriage +// allowing faster printing speeds. Connect your X2 stepper to the first unused E plug. +//#define DUAL_X_CARRIAGE +#if ENABLED(DUAL_X_CARRIAGE) + // Configuration for second X-carriage + // Note: the first x-carriage is defined as the x-carriage which homes to the minimum endstop; + // the second x-carriage always homes to the maximum endstop. + #define X2_MIN_POS 80 // set minimum to ensure second x-carriage doesn't hit the parked first X-carriage + #define X2_MAX_POS 353 // set maximum to the distance between toolheads when both heads are homed + #define X2_HOME_DIR 1 // the second X-carriage always homes to the maximum endstop position + #define X2_HOME_POS X2_MAX_POS // default home position is the maximum carriage position + // However: In this mode the HOTEND_OFFSET_X value for the second extruder provides a software + // override for X2_HOME_POS. This also allow recalibration of the distance between the two endstops + // without modifying the firmware (through the "M218 T1 X???" command). + // Remember: you should set the second extruder x-offset to 0 in your slicer. + + // There are a few selectable movement modes for dual x-carriages using M605 S + // Mode 0 (DXC_FULL_CONTROL_MODE): Full control. The slicer has full control over both x-carriages and can achieve optimal travel results + // as long as it supports dual x-carriages. (M605 S0) + // Mode 1 (DXC_AUTO_PARK_MODE) : Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so + // that additional slicer support is not required. (M605 S1) + // Mode 2 (DXC_DUPLICATION_MODE) : Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all + // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at + // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) + + // This is the default power-up mode which can be later using M605. + #define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_FULL_CONTROL_MODE + + // Default settings in "Auto-park Mode" + #define TOOLCHANGE_PARK_ZLIFT 0.2 // the distance to raise Z axis when parking an extruder + #define TOOLCHANGE_UNPARK_ZLIFT 1 // the distance to raise Z axis when unparking an extruder + + // Default x offset in duplication mode (typically set to half print bed width) + #define DEFAULT_DUPLICATION_X_OFFSET 100 + +#endif // DUAL_X_CARRIAGE + +// Activate a solenoid on the active extruder with M380. Disable all with M381. +// Define SOL0_PIN, SOL1_PIN, etc., for each extruder that has a solenoid. +//#define EXT_SOLENOID + +// @section homing + +// Homing hits each endstop, retracts by these distances, then does a slower bump. +#define X_HOME_BUMP_MM 5 +#define Y_HOME_BUMP_MM 5 +#define Z_HOME_BUMP_MM 2 +#define HOMING_BUMP_DIVISOR { 2, 2, 4 } // Re-Bump Speed Divisor (Divides the Homing Feedrate) +#define QUICK_HOME // If homing includes X and Y, do a diagonal move initially + +// When G28 is called, this option will make Y home before X +//#define HOME_Y_BEFORE_X + +// Enable this if X or Y can't home without homing the other axis first. +//#define CODEPENDENT_XY_HOMING + +// @section machine + +#define AXIS_RELATIVE_MODES {false, false, false, false} + +// Allow duplication mode with a basic dual-nozzle extruder +//#define DUAL_NOZZLE_DUPLICATION_MODE + +// By default pololu step drivers require an active high signal. However, some high power drivers require an active low signal as step. +#define INVERT_X_STEP_PIN false +#define INVERT_Y_STEP_PIN false +#define INVERT_Z_STEP_PIN false +#define INVERT_E_STEP_PIN false + +// Default stepper release if idle. Set to 0 to deactivate. +// Steppers will shut down DEFAULT_STEPPER_DEACTIVE_TIME seconds after the last move when DISABLE_INACTIVE_? is true. +// Time can be set by M18 and M84. +#define DEFAULT_STEPPER_DEACTIVE_TIME 120 +#define DISABLE_INACTIVE_X true +#define DISABLE_INACTIVE_Y true +#define DISABLE_INACTIVE_Z true // set to false if the nozzle will fall down on your printed part when print has finished. +#define DISABLE_INACTIVE_E true + +#define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate +#define DEFAULT_MINTRAVELFEEDRATE 0.0 + +//#define HOME_AFTER_DEACTIVATE // Require rehoming after steppers are deactivated + +// @section lcd + +#if ENABLED(ULTIPANEL) + #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 0} // Feedrates for manual moves along X, Y, Z, E from panel + #define ULTIPANEL_FEEDMULTIPLY // Comment to disable setting feedrate multiplier via encoder +#endif + +// @section extras + +// minimum time in microseconds that a movement needs to take if the buffer is emptied. +#define DEFAULT_MINSEGMENTTIME 20000 + +// If defined the movements slow down when the look ahead buffer is only half full +#define SLOWDOWN + +// Frequency limit +// See nophead's blog for more info +// Not working O +//#define XY_FREQUENCY_LIMIT 15 + +// Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end +// of the buffer and all stops. This should not be much greater than zero and should only be changed +// if unwanted behavior is observed on a user's machine when running at very slow speeds. +#define MINIMUM_PLANNER_SPEED 0.05 // (mm/sec) + +// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU. +#define MICROSTEP_MODES {16,16,16,16,16} // [1,2,4,8,16] + +/** + * @section stepper motor current + * + * Some boards have a means of setting the stepper motor current via firmware. + * + * The power on motor currents are set by: + * PWM_MOTOR_CURRENT - used by MINIRAMBO & ULTIMAIN_2 + * known compatible chips: A4982 + * DIGIPOT_MOTOR_CURRENT - used by BQ_ZUM_MEGA_3D, RAMBO & SCOOVO_X9H + * known compatible chips: AD5206 + * DAC_MOTOR_CURRENT_DEFAULT - used by PRINTRBOARD_REVF & RIGIDBOARD_V2 + * known compatible chips: MCP4728 + * DIGIPOT_I2C_MOTOR_CURRENTS - used by 5DPRINT, AZTEEG_X3_PRO, MIGHTYBOARD_REVE + * known compatible chips: MCP4451, MCP4018 + * + * Motor currents can also be set by M907 - M910 and by the LCD. + * M907 - applies to all. + * M908 - BQ_ZUM_MEGA_3D, RAMBO, PRINTRBOARD_REVF, RIGIDBOARD_V2 & SCOOVO_X9H + * M909, M910 & LCD - only PRINTRBOARD_REVF & RIGIDBOARD_V2 + */ +//#define PWM_MOTOR_CURRENT { 1300, 1300, 1250 } // Values in milliamps +//#define DIGIPOT_MOTOR_CURRENT { 135,135,135,135,135 } // Values 0-255 (RAMBO 135 = ~0.75A, 185 = ~1A) +//#define DAC_MOTOR_CURRENT_DEFAULT { 70, 80, 90, 80 } // Default drive percent - X, Y, Z, E axis + +// Use an I2C based DIGIPOT (e.g., Azteeg X3 Pro) +//#define DIGIPOT_I2C +#if ENABLED(DIGIPOT_I2C) && !defined(DIGIPOT_I2C_ADDRESS_A) + /** + * Common slave addresses: + * + * A (A shifted) B (B shifted) IC + * Smoothie 0x2C (0x58) 0x2D (0x5A) MCP4451 + * AZTEEG_X3_PRO 0x2C (0x58) 0x2E (0x5C) MCP4451 + * MIGHTYBOARD_REVE 0x2F (0x5E) MCP4018 + */ + #define DIGIPOT_I2C_ADDRESS_A 0x2C // unshifted slave address for first DIGIPOT + #define DIGIPOT_I2C_ADDRESS_B 0x2D // unshifted slave address for second DIGIPOT +#endif + +//#define DIGIPOT_MCP4018 // Requires library from https://github.com/stawel/SlowSoftI2CMaster +#define DIGIPOT_I2C_NUM_CHANNELS 8 // 5DPRINT: 4 AZTEEG_X3_PRO: 8 +// Actual motor currents in Amps. The number of entries must match DIGIPOT_I2C_NUM_CHANNELS. +// These correspond to the physical drivers, so be mindful if the order is changed. +#define DIGIPOT_I2C_MOTOR_CURRENTS { 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0 } // AZTEEG_X3_PRO + +//=========================================================================== +//=============================Additional Features=========================== +//=========================================================================== + +#define ENCODER_RATE_MULTIPLIER // If defined, certain menu edit operations automatically multiply the steps when the encoder is moved quickly +#define ENCODER_10X_STEPS_PER_SEC 75 // If the encoder steps per sec exceeds this value, multiply steps moved x10 to quickly advance the value +#define ENCODER_100X_STEPS_PER_SEC 160 // If the encoder steps per sec exceeds this value, multiply steps moved x100 to really quickly advance the value + +//#define CHDK 4 //Pin for triggering CHDK to take a picture see how to use it here http://captain-slow.dk/2014/03/09/3d-printing-timelapses/ +#define CHDK_DELAY 50 //How long in ms the pin should stay HIGH before going LOW again + +// @section lcd + +// Include a page of printer information in the LCD Main Menu +#define LCD_INFO_MENU + +// Scroll a longer status message into view +#define STATUS_MESSAGE_SCROLLING + +// On the Info Screen, display XY with one decimal place when possible +//#define LCD_DECIMAL_SMALL_XY + +// The timeout (in ms) to return to the status screen from sub-menus +//#define LCD_TIMEOUT_TO_STATUS 15000 + +// Add an 'M73' G-code to set the current percentage +//#define LCD_SET_PROGRESS_MANUALLY + +#if ENABLED(SDSUPPORT) || ENABLED(LCD_SET_PROGRESS_MANUALLY) + //#define LCD_PROGRESS_BAR // Show a progress bar on HD44780 LCDs for SD printing + #if ENABLED(LCD_PROGRESS_BAR) + #define PROGRESS_BAR_BAR_TIME 2000 // (ms) Amount of time to show the bar + #define PROGRESS_BAR_MSG_TIME 3000 // (ms) Amount of time to show the status message + #define PROGRESS_MSG_EXPIRE 0 // (ms) Amount of time to retain the status message (0=forever) + //#define PROGRESS_MSG_ONCE // Show the message for MSG_TIME then clear it + //#define LCD_PROGRESS_BAR_TEST // Add a menu item to test the progress bar + #endif +#endif // SDSUPPORT || LCD_SET_PROGRESS_MANUALLY + +/** + * LED Control Menu + * Enable this feature to add LED Control to the LCD menu + */ +//#define LED_CONTROL_MENU +#if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif +#endif // LED_CONTROL_MENU + +#if ENABLED(SDSUPPORT) + + // Some RAMPS and other boards don't detect when an SD card is inserted. You can work + // around this by connecting a push button or single throw switch to the pin defined + // as SD_DETECT_PIN in your board's pins definitions. + // This setting should be disabled unless you are using a push button, pulling the pin to ground. + // Note: This is always disabled for ULTIPANEL (except ELB_FULL_GRAPHIC_CONTROLLER). + #define SD_DETECT_INVERTED + + #define SD_FINISHED_STEPPERRELEASE true // Disable steppers when SD Print is finished + #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place. + + // Reverse SD sort to show "more recent" files first, according to the card's FAT. + // Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended. + #define SDCARD_RATHERRECENTFIRST + + // Add an option in the menu to run all auto#.g files + //#define MENU_ADDAUTOSTART + + /** + * Continue after Power-Loss (Creality3D) + * + * Store the current state to the SD Card at the start of each layer + * during SD printing. If the recovery file is found at boot time, present + * an option on the LCD screen to continue the print from the last-known + * point in the file. + */ + //#define POWER_LOSS_RECOVERY + + /** + * Sort SD file listings in alphabetical order. + * + * With this option enabled, items on SD cards will be sorted + * by name for easier navigation. + * + * By default... + * + * - Use the slowest -but safest- method for sorting. + * - Folders are sorted to the top. + * - The sort key is statically allocated. + * - No added G-code (M34) support. + * - 40 item sorting limit. (Items after the first 40 are unsorted.) + * + * SD sorting uses static allocation (as set by SDSORT_LIMIT), allowing the + * compiler to calculate the worst-case usage and throw an error if the SRAM + * limit is exceeded. + * + * - SDSORT_USES_RAM provides faster sorting via a static directory buffer. + * - SDSORT_USES_STACK does the same, but uses a local stack-based buffer. + * - SDSORT_CACHE_NAMES will retain the sorted file listing in RAM. (Expensive!) + * - SDSORT_DYNAMIC_RAM only uses RAM when the SD menu is visible. (Use with caution!) + */ + //#define SDCARD_SORT_ALPHA + + // SD Card Sorting options + #if ENABLED(SDCARD_SORT_ALPHA) + #define SDSORT_LIMIT 40 // Maximum number of sorted items (10-256). Costs 27 bytes each. + #define FOLDER_SORTING -1 // -1=above 0=none 1=below + #define SDSORT_GCODE false // Allow turning sorting on/off with LCD and M34 g-code. + #define SDSORT_USES_RAM false // Pre-allocate a static array for faster pre-sorting. + #define SDSORT_USES_STACK false // Prefer the stack for pre-sorting to give back some SRAM. (Negated by next 2 options.) + #define SDSORT_CACHE_NAMES false // Keep sorted items in RAM longer for speedy performance. Most expensive option. + #define SDSORT_DYNAMIC_RAM false // Use dynamic allocation (within SD menus). Least expensive option. Set SDSORT_LIMIT before use! + #define SDSORT_CACHE_VFATS 2 // Maximum number of 13-byte VFAT entries to use for sorting. + // Note: Only affects SCROLL_LONG_FILENAMES with SDSORT_CACHE_NAMES but not SDSORT_DYNAMIC_RAM. + #endif + + // This allows hosts to request long names for files and folders with M33 + //#define LONG_FILENAME_HOST_SUPPORT + + // Enable this option to scroll long filenames in the SD card menu + #define SCROLL_LONG_FILENAMES + + /** + * This option allows you to abort SD printing when any endstop is triggered. + * This feature must be enabled with "M540 S1" or from the LCD menu. + * To have any effect, endstops must be enabled during SD printing. + */ + //#define ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED + + /** + * This option makes it easier to print the same SD Card file again. + * On print completion the LCD Menu will open with the file selected. + * You can just click to start the print, or navigate elsewhere. + */ + //#define SD_REPRINT_LAST_SELECTED_FILE + + /** + * Auto-report SdCard status with M27 S + */ + //#define AUTO_REPORT_SD_STATUS + +#endif // SDSUPPORT + +/** + * Additional options for Graphical Displays + * + * Use the optimizations here to improve printing performance, + * which can be adversely affected by graphical display drawing, + * especially when doing several short moves, and when printing + * on DELTA and SCARA machines. + * + * Some of these options may result in the display lagging behind + * controller events, as there is a trade-off between reliable + * printing performance versus fast display updates. + */ +#if ENABLED(DOGLCD) + // Show SD percentage next to the progress bar + //#define DOGM_SD_PERCENT + + // Enable to save many cycles by drawing a hollow frame on the Info Screen + #define XYZ_HOLLOW_FRAME + + // Enable to save many cycles by drawing a hollow frame on Menu Screens + #define MENU_HOLLOW_FRAME + + // A bigger font is available for edit items. Costs 3120 bytes of PROGMEM. + // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese. + //#define USE_BIG_EDIT_FONT + + // A smaller font may be used on the Info Screen. Costs 2300 bytes of PROGMEM. + // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese. + //#define USE_SMALL_INFOFONT + + // Enable this option and reduce the value to optimize screen updates. + // The normal delay is 10µs. Use the lowest value that still gives a reliable display. + //#define DOGM_SPI_DELAY_US 5 + + // Swap the CW/CCW indicators in the graphics overlay + //#define OVERLAY_GFX_REVERSE + + #if ENABLED(U8GLIB_ST7920) + /** + * ST7920-based LCDs can emulate a 16 x 4 character display using + * the ST7920 character-generator for very fast screen updates. + * Enable LIGHTWEIGHT_UI to use this special display mode. + * + * Since LIGHTWEIGHT_UI has limited space, the position and status + * message occupy the same line. Set STATUS_EXPIRE_SECONDS to the + * length of time to display the status message before clearing. + * + * Set STATUS_EXPIRE_SECONDS to zero to never clear the status. + * This will prevent position updates from being displayed. + */ + //#define LIGHTWEIGHT_UI + #if ENABLED(LIGHTWEIGHT_UI) + #define STATUS_EXPIRE_SECONDS 20 + #endif + #endif + +#endif // DOGLCD + +// @section safety + +// The hardware watchdog should reset the microcontroller disabling all outputs, +// in case the firmware gets stuck and doesn't do temperature regulation. +#define USE_WATCHDOG + +#if ENABLED(USE_WATCHDOG) + // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on. + // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset. + // However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled. + //#define WATCHDOG_RESET_MANUAL +#endif + +// @section lcd + +/** + * Babystepping enables movement of the axes by tiny increments without changing + * the current position values. This feature is used primarily to adjust the Z + * axis in the first layer of a print in real-time. + * + * Warning: Does not respect endstops! + */ +#define BABYSTEPPING +#if ENABLED(BABYSTEPPING) + //#define BABYSTEP_XY // Also enable X/Y Babystepping. Not supported on DELTA! + #define BABYSTEP_INVERT_Z false // Change if Z babysteps should go the other way + #define BABYSTEP_MULTIPLICATOR 1 // Babysteps are very small. Increase for faster motion. + //#define BABYSTEP_ZPROBE_OFFSET // Enable to combine M851 and Babystepping + #define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping. + #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds. + // Note: Extra time may be added to mitigate controller latency. + //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor +#endif + +// @section extruder + +/** + * Linear Pressure Control v1.5 + * + * Assumption: advance [steps] = k * (delta velocity [steps/s]) + * K=0 means advance disabled. + * + * NOTE: K values for LIN_ADVANCE 1.5 differ from earlier versions! + * + * Set K around 0.22 for 3mm PLA Direct Drive with ~6.5cm between the drive gear and heatbreak. + * Larger K values will be needed for flexible filament and greater distances. + * If this algorithm produces a higher speed offset than the extruder can handle (compared to E jerk) + * print acceleration will be reduced during the affected moves to keep within the limit. + * + * See http://marlinfw.org/docs/features/lin_advance.html for full instructions. + * Mention @Sebastianv650 on GitHub to alert the author of any issues. + */ +//#define LIN_ADVANCE +#if ENABLED(LIN_ADVANCE) + #define LIN_ADVANCE_K 0.22 // Unit: mm compression per 1mm/s extruder speed + //#define LA_DEBUG // If enabled, this will generate debug information output over USB. +#endif + +// @section leveling + +#if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_UBL) + // Override the mesh area if the automatic (max) area is too large + //#define MESH_MIN_X MESH_INSET + //#define MESH_MIN_Y MESH_INSET + //#define MESH_MAX_X X_BED_SIZE - (MESH_INSET) + //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET) +#endif + +/** + * Repeatedly attempt G29 leveling until it succeeds. + * Stop after G29_MAX_RETRIES attempts. + */ +//#define G29_RETRY_AND_RECOVER +#if ENABLED(G29_RETRY_AND_RECOVER) + #define G29_MAX_RETRIES 3 + #define G29_HALT_ON_FAILURE + /** + * Specify the GCODE commands that will be executed when leveling succeeds, + * between attempts, and after the maximum number of retries have been tried. + */ + #define G29_SUCCESS_COMMANDS "M117 Bed leveling done." + #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0" + #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1" + /** + * Specify an action command to send to the host on a recovery attempt or failure. + * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'. + * The host must be configured to handle the action command. + */ + #define G29_ACTION_ON_RECOVER "probe_rewipe" + #define G29_ACTION_ON_FAILURE "probe_failed" +#endif + +// @section extras + +// +// G2/G3 Arc Support +// +#define ARC_SUPPORT // Disable this feature to save ~3226 bytes +#if ENABLED(ARC_SUPPORT) + #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment + #define N_ARC_CORRECTION 25 // Number of intertpolated segments between corrections + //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles + //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes +#endif + +// Support for G5 with XYZE destination and IJPQ offsets. Requires ~2666 bytes. +//#define BEZIER_CURVE_SUPPORT + +// G38.2 and G38.3 Probe Target +// Set MULTIPLE_PROBING if you want G38 to double touch +//#define G38_PROBE_TARGET +#if ENABLED(G38_PROBE_TARGET) + #define G38_MINIMUM_MOVE 0.0275 // minimum distance in mm that will produce a move (determined using the print statement in check_move) +#endif + +// Moves (or segments) with fewer steps than this will be joined with the next move +#define MIN_STEPS_PER_SEGMENT 6 + +// The minimum pulse width (in µs) for stepping a stepper. +// Set this if you find stepping unreliable, or if using a very fast CPU. +// 0 is OK for AVR, 0 is OK for A4989 drivers, 2 is needed for DRV8825 drivers +#define MINIMUM_STEPPER_PULSE 2 // (µs) DRV8825 on 32bit CPUs + +// @section temperature + +// Control heater 0 and heater 1 in parallel. +//#define HEATERS_PARALLEL + +//=========================================================================== +//================================= Buffers ================================= +//=========================================================================== + +// @section hidden + +// The number of linear motions that can be in the plan at any give time. +// THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2 (e.g. 8, 16, 32) because shifts and ors are used to do the ring-buffering. +#if ENABLED(SDSUPPORT) + #define BLOCK_BUFFER_SIZE 16 // SD,LCD,Buttons take more memory, block buffer needs to be smaller +#else + #define BLOCK_BUFFER_SIZE 16 // maximize block buffer +#endif + +// @section serial + +// The ASCII buffer for serial input +#define MAX_CMD_SIZE 96 +#define BUFSIZE 4 + +// Transmission to Host Buffer Size +// To save 386 bytes of PROGMEM (and TX_BUFFER_SIZE+3 bytes of RAM) set to 0. +// To buffer a simple "ok" you need 4 bytes. +// For ADVANCED_OK (M105) you need 32 bytes. +// For debug-echo: 128 bytes for the optimal speed. +// Other output doesn't need to be that speedy. +// :[0, 2, 4, 8, 16, 32, 64, 128, 256] +#define TX_BUFFER_SIZE 0 + +// Host Receive Buffer Size +// Without XON/XOFF flow control (see SERIAL_XON_XOFF below) 32 bytes should be enough. +// To use flow control, set this buffer size to at least 1024 bytes. +// :[0, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1024, 2048] +//#define RX_BUFFER_SIZE 1024 + +#if RX_BUFFER_SIZE >= 1024 + // Enable to have the controller send XON/XOFF control characters to + // the host to signal the RX buffer is becoming full. + //#define SERIAL_XON_XOFF +#endif + +#if ENABLED(SDSUPPORT) + // Enable this option to collect and display the maximum + // RX queue usage after transferring a file to SD. + //#define SERIAL_STATS_MAX_RX_QUEUED + + // Enable this option to collect and display the number + // of dropped bytes after a file transfer to SD. + //#define SERIAL_STATS_DROPPED_RX +#endif + +// Enable an emergency-command parser to intercept certain commands as they +// enter the serial receive buffer, so they cannot be blocked. +// Currently handles M108, M112, M410 +// Does not work on boards using AT90USB (USBCON) processors! +//#define EMERGENCY_PARSER + +// Bad Serial-connections can miss a received command by sending an 'ok' +// Therefore some clients abort after 30 seconds in a timeout. +// Some other clients start sending commands while receiving a 'wait'. +// This "wait" is only sent when the buffer is empty. 1 second is a good value here. +//#define NO_TIMEOUTS 1000 // Milliseconds + +// Some clients will have this feature soon. This could make the NO_TIMEOUTS unnecessary. +//#define ADVANCED_OK + +// @section extras + +/** + * Firmware-based and LCD-controlled retract + * + * Add G10 / G11 commands for automatic firmware-based retract / recover. + * Use M207 and M208 to define parameters for retract / recover. + * + * Use M209 to enable or disable auto-retract. + * With auto-retract enabled, all G1 E moves within the set range + * will be converted to firmware-based retract/recover moves. + * + * Be sure to turn off auto-retract during filament change. + * + * Note that M207 / M208 / M209 settings are saved to EEPROM. + * + */ +//#define FWRETRACT // ONLY PARTIALLY TESTED +#if ENABLED(FWRETRACT) + #define MIN_AUTORETRACT 0.1 // When auto-retract is on, convert E moves of this length and over + #define MAX_AUTORETRACT 10.0 // Upper limit for auto-retract conversion + #define RETRACT_LENGTH 3 // Default retract length (positive mm) + #define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change + #define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s) + #define RETRACT_ZLIFT 0 // Default retract Z-lift + #define RETRACT_RECOVER_LENGTH 0 // Default additional recover length (mm, added to retract length when recovering) + #define RETRACT_RECOVER_LENGTH_SWAP 0 // Default additional swap recover length (mm, added to retract length when recovering from extruder change) + #define RETRACT_RECOVER_FEEDRATE 8 // Default feedrate for recovering from retraction (mm/s) + #define RETRACT_RECOVER_FEEDRATE_SWAP 8 // Default feedrate for recovering from swap retraction (mm/s) +#endif + +/** + * Extra Fan Speed + * Adds a secondary fan speed for each print-cooling fan. + * 'M106 P T3-255' : Set a secondary speed for + * 'M106 P T2' : Use the set secondary speed + * 'M106 P T1' : Restore the previous fan speed + */ +//#define EXTRA_FAN_SPEED + +/** + * Advanced Pause + * Experimental feature for filament change support and for parking the nozzle when paused. + * Adds the GCode M600 for initiating filament change. + * If PARK_HEAD_ON_PAUSE enabled, adds the GCode M125 to pause printing and park the nozzle. + * + * Requires an LCD display. + * Requires NOZZLE_PARK_FEATURE. + * This feature is required for the default FILAMENT_RUNOUT_SCRIPT. + */ +//#define ADVANCED_PAUSE_FEATURE +#if ENABLED(ADVANCED_PAUSE_FEATURE) + #define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate. + #define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract. + // This short retract is done immediately, before parking the nozzle. + #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast. + #define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate. + #define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload. + // For Bowden, the full length of the tube and nozzle. + // For direct drive, the full length of the nozzle. + // Set to 0 for manual unloading. + #define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load. + #define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material. + // 0 to disable start loading and skip to fast load only + #define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast. + #define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate. + #define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle. + // For Bowden, the full length of the tube and nozzle. + // For direct drive, the full length of the nozzle. + //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted. + #define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate. + #define ADVANCED_PAUSE_PURGE_LENGTH 50 // (mm) Length to extrude after loading. + // Set to 0 for manual extrusion. + // Filament can be extruded repeatedly from the Filament Change menu + // until extrusion is consistent, and to purge old filament. + + // Filament Unload does a Retract, Delay, and Purge first: + #define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length. + #define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract. + #define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged. + + #define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety. + #define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed. + #define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change. + + //#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change. + //#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change + + //#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu. + //#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302) +#endif + +// @section tmc + +/** + * Enable this section if you have TMC26X motor drivers. + * You will need to import the TMC26XStepper library into the Arduino IDE for this + * (https://github.com/trinamic/TMC26XStepper.git) + */ +//#define HAVE_TMC26X +#if ENABLED(HAVE_TMC26X) // Choose your axes here. This is mandatory! + //#define X_IS_TMC26X + //#define X2_IS_TMC26X + //#define Y_IS_TMC26X + //#define Y2_IS_TMC26X + //#define Z_IS_TMC26X + //#define Z2_IS_TMC26X + //#define E0_IS_TMC26X + //#define E1_IS_TMC26X + //#define E2_IS_TMC26X + //#define E3_IS_TMC26X + //#define E4_IS_TMC26X + + #define X_MAX_CURRENT 1000 // in mA + #define X_SENSE_RESISTOR 91 // in mOhms + #define X_MICROSTEPS 16 // number of microsteps + + #define X2_MAX_CURRENT 1000 + #define X2_SENSE_RESISTOR 91 + #define X2_MICROSTEPS 16 + + #define Y_MAX_CURRENT 1000 + #define Y_SENSE_RESISTOR 91 + #define Y_MICROSTEPS 16 + + #define Y2_MAX_CURRENT 1000 + #define Y2_SENSE_RESISTOR 91 + #define Y2_MICROSTEPS 16 + + #define Z_MAX_CURRENT 1000 + #define Z_SENSE_RESISTOR 91 + #define Z_MICROSTEPS 16 + + #define Z2_MAX_CURRENT 1000 + #define Z2_SENSE_RESISTOR 91 + #define Z2_MICROSTEPS 16 + + #define E0_MAX_CURRENT 1000 + #define E0_SENSE_RESISTOR 91 + #define E0_MICROSTEPS 16 + + #define E1_MAX_CURRENT 1000 + #define E1_SENSE_RESISTOR 91 + #define E1_MICROSTEPS 16 + + #define E2_MAX_CURRENT 1000 + #define E2_SENSE_RESISTOR 91 + #define E2_MICROSTEPS 16 + + #define E3_MAX_CURRENT 1000 + #define E3_SENSE_RESISTOR 91 + #define E3_MICROSTEPS 16 + + #define E4_MAX_CURRENT 1000 + #define E4_SENSE_RESISTOR 91 + #define E4_MICROSTEPS 16 + +#endif + +// @section tmc_smart + +/** + * Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers. + * + * You'll also need the TMC2130Stepper Arduino library + * (https://github.com/teemuatlut/TMC2130Stepper). + * + * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to + * the hardware SPI interface on your board and define the required CS pins + * in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.). + * You may also use software SPI if you wish to use general purpose IO pins. + */ +//#define HAVE_TMC2130 +#if ENABLED(HAVE_TMC2130) // Choose your axes here. This is mandatory! + //#define X_IS_TMC2130 + //#define X2_IS_TMC2130 + //#define Y_IS_TMC2130 + //#define Y2_IS_TMC2130 + //#define Z_IS_TMC2130 + //#define Z2_IS_TMC2130 + //#define E0_IS_TMC2130 + //#define E1_IS_TMC2130 + //#define E2_IS_TMC2130 + //#define E3_IS_TMC2130 + //#define E4_IS_TMC2130 +#endif + +/** + * Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers. + * Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor. + * To use the reading capabilities, also connect #_SERIAL_RX_PIN + * to PDN_UART without a resistor. + * The drivers can also be used with hardware serial. + * + * You'll also need the TMC2208Stepper Arduino library + * (https://github.com/teemuatlut/TMC2208Stepper). + */ +//#define HAVE_TMC2208 +#if ENABLED(HAVE_TMC2208) // Choose your axes here. This is mandatory! + //#define X_IS_TMC2208 + //#define X2_IS_TMC2208 + //#define Y_IS_TMC2208 + //#define Y2_IS_TMC2208 + //#define Z_IS_TMC2208 + //#define Z2_IS_TMC2208 + //#define E0_IS_TMC2208 + //#define E1_IS_TMC2208 + //#define E2_IS_TMC2208 + //#define E3_IS_TMC2208 + //#define E4_IS_TMC2208 +#endif + +#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208) + + #define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130 + #define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current + #define INTERPOLATE true // Interpolate X/Y/Z_MICROSTEPS to 256 + + #define X_CURRENT 800 // rms current in mA. Multiply by 1.41 for peak current. + #define X_MICROSTEPS 16 // 0..256 + + #define Y_CURRENT 800 + #define Y_MICROSTEPS 16 + + #define Z_CURRENT 800 + #define Z_MICROSTEPS 16 + + #define X2_CURRENT 800 + #define X2_MICROSTEPS 16 + + #define Y2_CURRENT 800 + #define Y2_MICROSTEPS 16 + + #define Z2_CURRENT 800 + #define Z2_MICROSTEPS 16 + + #define E0_CURRENT 800 + #define E0_MICROSTEPS 16 + + #define E1_CURRENT 800 + #define E1_MICROSTEPS 16 + + #define E2_CURRENT 800 + #define E2_MICROSTEPS 16 + + #define E3_CURRENT 800 + #define E3_MICROSTEPS 16 + + #define E4_CURRENT 800 + #define E4_MICROSTEPS 16 + + /** + * Use software SPI for TMC2130. + * The default SW SPI pins are defined the respective pins files, + * but you can override or define them here. + */ + //#define TMC_USE_SW_SPI + //#define TMC_SW_MOSI -1 + //#define TMC_SW_MISO -1 + //#define TMC_SW_SCK -1 + + /** + * Use Trinamic's ultra quiet stepping mode. + * When disabled, Marlin will use spreadCycle stepping mode. + */ + #define STEALTHCHOP + + /** + * Monitor Trinamic TMC2130 and TMC2208 drivers for error conditions, + * like overtemperature and short to ground. TMC2208 requires hardware serial. + * In the case of overtemperature Marlin can decrease the driver current until error condition clears. + * Other detected conditions can be used to stop the current print. + * Relevant g-codes: + * M906 - Set or get motor current in milliamps using axis codes X, Y, Z, E. Report values if no axis codes given. + * M911 - Report stepper driver overtemperature pre-warn condition. + * M912 - Clear stepper driver overtemperature pre-warn condition flag. + * M122 S0/1 - Report driver parameters (Requires TMC_DEBUG) + */ + //#define MONITOR_DRIVER_STATUS + + #if ENABLED(MONITOR_DRIVER_STATUS) + #define CURRENT_STEP_DOWN 50 // [mA] + #define REPORT_CURRENT_CHANGE + #define STOP_ON_ERROR + #endif + + /** + * The driver will switch to spreadCycle when stepper speed is over HYBRID_THRESHOLD. + * This mode allows for faster movements at the expense of higher noise levels. + * STEALTHCHOP needs to be enabled. + * M913 X/Y/Z/E to live tune the setting + */ + //#define HYBRID_THRESHOLD + + #define X_HYBRID_THRESHOLD 100 // [mm/s] + #define X2_HYBRID_THRESHOLD 100 + #define Y_HYBRID_THRESHOLD 100 + #define Y2_HYBRID_THRESHOLD 100 + #define Z_HYBRID_THRESHOLD 3 + #define Z2_HYBRID_THRESHOLD 3 + #define E0_HYBRID_THRESHOLD 30 + #define E1_HYBRID_THRESHOLD 30 + #define E2_HYBRID_THRESHOLD 30 + #define E3_HYBRID_THRESHOLD 30 + #define E4_HYBRID_THRESHOLD 30 + + /** + * Use stallGuard2 to sense an obstacle and trigger an endstop. + * You need to place a wire from the driver's DIAG1 pin to the X/Y endstop pin. + * X, Y, and Z homing will always be done in spreadCycle mode. + * + * X/Y/Z_HOMING_SENSITIVITY is used for tuning the trigger sensitivity. + * Higher values make the system LESS sensitive. + * Lower value make the system MORE sensitive. + * Too low values can lead to false positives, while too high values will collide the axis without triggering. + * It is advised to set X/Y/Z_HOME_BUMP_MM to 0. + * M914 X/Y/Z to live tune the setting + */ + //#define SENSORLESS_HOMING // TMC2130 only + + #if ENABLED(SENSORLESS_HOMING) + #define X_HOMING_SENSITIVITY 8 + #define Y_HOMING_SENSITIVITY 8 + #define Z_HOMING_SENSITIVITY 8 + #endif + + /** + * Enable M122 debugging command for TMC stepper drivers. + * M122 S0/1 will enable continous reporting. + */ + //#define TMC_DEBUG + + /** + * M915 Z Axis Calibration + * + * - Adjust Z stepper current, + * - Drive the Z axis to its physical maximum, and + * - Home Z to account for the lost steps. + * + * Use M915 Snn to specify the current. + * Use M925 Znn to add extra Z height to Z_MAX_POS. + */ + //#define TMC_Z_CALIBRATION + #if ENABLED(TMC_Z_CALIBRATION) + #define CALIBRATION_CURRENT 250 + #define CALIBRATION_EXTRA_HEIGHT 10 + #endif + + /** + * You can set your own advanced settings by filling in predefined functions. + * A list of available functions can be found on the library github page + * https://github.com/teemuatlut/TMC2130Stepper + * https://github.com/teemuatlut/TMC2208Stepper + * + * Example: + * #define TMC_ADV() { \ + * stepperX.diag0_temp_prewarn(1); \ + * stepperY.interpolate(0); \ + * } + */ + #define TMC_ADV() { } + +#endif // TMC2130 || TMC2208 + +// @section L6470 + +/** + * Enable this section if you have L6470 motor drivers. + * You need to import the L6470 library into the Arduino IDE for this. + * (https://github.com/ameyer/Arduino-L6470) + */ + +//#define HAVE_L6470DRIVER +#if ENABLED(HAVE_L6470DRIVER) + + //#define X_IS_L6470 + //#define X2_IS_L6470 + //#define Y_IS_L6470 + //#define Y2_IS_L6470 + //#define Z_IS_L6470 + //#define Z2_IS_L6470 + //#define E0_IS_L6470 + //#define E1_IS_L6470 + //#define E2_IS_L6470 + //#define E3_IS_L6470 + //#define E4_IS_L6470 + + #define X_MICROSTEPS 16 // number of microsteps + #define X_OVERCURRENT 2000 // maxc current in mA. If the current goes over this value, the driver will switch off + #define X_STALLCURRENT 1500 // current in mA where the driver will detect a stall + + #define X2_MICROSTEPS 16 + #define X2_OVERCURRENT 2000 + #define X2_STALLCURRENT 1500 + + #define Y_MICROSTEPS 16 + #define Y_OVERCURRENT 2000 + #define Y_STALLCURRENT 1500 + + #define Y2_MICROSTEPS 16 + #define Y2_OVERCURRENT 2000 + #define Y2_STALLCURRENT 1500 + + #define Z_MICROSTEPS 16 + #define Z_OVERCURRENT 2000 + #define Z_STALLCURRENT 1500 + + #define Z2_MICROSTEPS 16 + #define Z2_OVERCURRENT 2000 + #define Z2_STALLCURRENT 1500 + + #define E0_MICROSTEPS 16 + #define E0_OVERCURRENT 2000 + #define E0_STALLCURRENT 1500 + + #define E1_MICROSTEPS 16 + #define E1_OVERCURRENT 2000 + #define E1_STALLCURRENT 1500 + + #define E2_MICROSTEPS 16 + #define E2_OVERCURRENT 2000 + #define E2_STALLCURRENT 1500 + + #define E3_MICROSTEPS 16 + #define E3_OVERCURRENT 2000 + #define E3_STALLCURRENT 1500 + + #define E4_MICROSTEPS 16 + #define E4_OVERCURRENT 2000 + #define E4_STALLCURRENT 1500 + +#endif + +/** + * TWI/I2C BUS + * + * This feature is an EXPERIMENTAL feature so it shall not be used on production + * machines. Enabling this will allow you to send and receive I2C data from slave + * devices on the bus. + * + * ; Example #1 + * ; This macro send the string "Marlin" to the slave device with address 0x63 (99) + * ; It uses multiple M260 commands with one B arg + * M260 A99 ; Target slave address + * M260 B77 ; M + * M260 B97 ; a + * M260 B114 ; r + * M260 B108 ; l + * M260 B105 ; i + * M260 B110 ; n + * M260 S1 ; Send the current buffer + * + * ; Example #2 + * ; Request 6 bytes from slave device with address 0x63 (99) + * M261 A99 B5 + * + * ; Example #3 + * ; Example serial output of a M261 request + * echo:i2c-reply: from:99 bytes:5 data:hello + */ + +// @section i2cbus + +//#define EXPERIMENTAL_I2CBUS +#define I2C_SLAVE_ADDRESS 0 // Set a value from 8 to 127 to act as a slave + +// @section extras + +/** + * Spindle & Laser control + * + * Add the M3, M4, and M5 commands to turn the spindle/laser on and off, and + * to set spindle speed, spindle direction, and laser power. + * + * SuperPid is a router/spindle speed controller used in the CNC milling community. + * Marlin can be used to turn the spindle on and off. It can also be used to set + * the spindle speed from 5,000 to 30,000 RPM. + * + * You'll need to select a pin for the ON/OFF function and optionally choose a 0-5V + * hardware PWM pin for the speed control and a pin for the rotation direction. + * + * See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details. + */ +//#define SPINDLE_LASER_ENABLE +#if ENABLED(SPINDLE_LASER_ENABLE) + + #define SPINDLE_LASER_ENABLE_INVERT false // set to "true" if the on/off function is reversed + #define SPINDLE_LASER_PWM true // set to true if your controller supports setting the speed/power + #define SPINDLE_LASER_PWM_INVERT true // set to "true" if the speed/power goes up when you want it to go slower + #define SPINDLE_LASER_POWERUP_DELAY 5000 // delay in milliseconds to allow the spindle/laser to come up to speed/power + #define SPINDLE_LASER_POWERDOWN_DELAY 5000 // delay in milliseconds to allow the spindle to stop + #define SPINDLE_DIR_CHANGE true // set to true if your spindle controller supports changing spindle direction + #define SPINDLE_INVERT_DIR false + #define SPINDLE_STOP_ON_DIR_CHANGE true // set to true if Marlin should stop the spindle before changing rotation direction + + /** + * The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power + * + * SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT + * where PWM duty cycle varies from 0 to 255 + * + * set the following for your controller (ALL MUST BE SET) + */ + + #define SPEED_POWER_SLOPE 118.4 + #define SPEED_POWER_INTERCEPT 0 + #define SPEED_POWER_MIN 5000 + #define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM + + //#define SPEED_POWER_SLOPE 0.3922 + //#define SPEED_POWER_INTERCEPT 0 + //#define SPEED_POWER_MIN 10 + //#define SPEED_POWER_MAX 100 // 0-100% +#endif + +/** + * Filament Width Sensor + * + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ +//#define FILAMENT_WIDTH_SENSOR + +#if ENABLED(FILAMENT_WIDTH_SENSOR) + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber + + #define FILWIDTH_ERROR_MARGIN 1.0 // (mm) If a measurement differs too much from nominal width ignore it + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. + + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially + + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. + //#define FILAMENT_LCD_DISPLAY +#endif + +/** + * CNC Coordinate Systems + * + * Enables G53 and G54-G59.3 commands to select coordinate systems + * and G92.1 to reset the workspace to native machine space. + */ +//#define CNC_COORDINATE_SYSTEMS + +/** + * M43 - display pin status, watch pins for changes, watch endstops & toggle LED, Z servo probe test, toggle pins + */ +//#define PINS_DEBUGGING + +/** + * Auto-report temperatures with M155 S + */ +#define AUTO_REPORT_TEMPERATURES + +/** + * Include capabilities in M115 output + */ +#define EXTENDED_CAPABILITIES_REPORT + +/** + * Disable all Volumetric extrusion options + */ +//#define NO_VOLUMETRICS + +#if DISABLED(NO_VOLUMETRICS) + /** + * Volumetric extrusion default state + * Activate to make volumetric extrusion the default method, + * with DEFAULT_NOMINAL_FILAMENT_DIA as the default diameter. + * + * M200 D0 to disable, M200 Dn to set a new diameter. + */ + //#define VOLUMETRIC_DEFAULT_ON +#endif + +/** + * Enable this option for a leaner build of Marlin that removes all + * workspace offsets, simplifying coordinate transformations, leveling, etc. + * + * - M206 and M428 are disabled. + * - G92 will revert to its behavior from Marlin 1.0. + */ +//#define NO_WORKSPACE_OFFSETS + +/** + * Set the number of proportional font spaces required to fill up a typical character space. + * This can help to better align the output of commands like `G29 O` Mesh Output. + * + * For clients that use a fixed-width font (like OctoPrint), leave this set to 1.0. + * Otherwise, adjust according to your client and font. + */ +#define PROPORTIONAL_FONT_RATIO 1.0 + +/** + * Spend 28 bytes of SRAM to optimize the GCode parser + */ +#define FASTER_GCODE_PARSER + +/** + * User-defined menu items that execute custom GCode + */ +//#define CUSTOM_USER_MENUS +#if ENABLED(CUSTOM_USER_MENUS) + #define USER_SCRIPT_DONE "M117 User Script Done" + #define USER_SCRIPT_AUDIBLE_FEEDBACK + //#define USER_SCRIPT_RETURN // Return to status screen after a script + + #define USER_DESC_1 "Home & UBL Info" + #define USER_GCODE_1 "G28\nG29 W" + + #define USER_DESC_2 "Preheat for PLA" + #define USER_GCODE_2 "M140 S" STRINGIFY(PREHEAT_1_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_1_TEMP_HOTEND) + + #define USER_DESC_3 "Preheat for ABS" + #define USER_GCODE_3 "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_2_TEMP_HOTEND) + + #define USER_DESC_4 "Heat Bed/Home/Level" + #define USER_GCODE_4 "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nG28\nG29" + + #define USER_DESC_5 "Home & Info" + #define USER_GCODE_5 "G28\nM503" +#endif + +/** + * Specify an action command to send to the host when the printer is killed. + * Will be sent in the form '//action:ACTION_ON_KILL', e.g. '//action:poweroff'. + * The host must be configured to handle the action command. + */ +//#define ACTION_ON_KILL "poweroff" + +/** + * Specify an action command to send to the host on pause and resume. + * Will be sent in the form '//action:ACTION_ON_PAUSE', e.g. '//action:pause'. + * The host must be configured to handle the action command. + */ +//#define ACTION_ON_PAUSE "pause" +//#define ACTION_ON_RESUME "resume" + +//=========================================================================== +//====================== I2C Position Encoder Settings ====================== +//=========================================================================== + +/** + * I2C position encoders for closed loop control. + * Developed by Chris Barr at Aus3D. + * + * Wiki: http://wiki.aus3d.com.au/Magnetic_Encoder + * Github: https://github.com/Aus3D/MagneticEncoder + * + * Supplier: http://aus3d.com.au/magnetic-encoder-module + * Alternative Supplier: http://reliabuild3d.com/ + * + * Reilabuild encoders have been modified to improve reliability. + */ + +//#define I2C_POSITION_ENCODERS +#if ENABLED(I2C_POSITION_ENCODERS) + + #define I2CPE_ENCODER_CNT 1 // The number of encoders installed; max of 5 + // encoders supported currently. + + #define I2CPE_ENC_1_ADDR I2CPE_PRESET_ADDR_X // I2C address of the encoder. 30-200. + #define I2CPE_ENC_1_AXIS X_AXIS // Axis the encoder module is installed on. _AXIS. + #define I2CPE_ENC_1_TYPE I2CPE_ENC_TYPE_LINEAR // Type of encoder: I2CPE_ENC_TYPE_LINEAR -or- + // I2CPE_ENC_TYPE_ROTARY. + #define I2CPE_ENC_1_TICKS_UNIT 2048 // 1024 for magnetic strips with 2mm poles; 2048 for + // 1mm poles. For linear encoders this is ticks / mm, + // for rotary encoders this is ticks / revolution. + //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper + // steps per full revolution (motor steps/rev * microstepping) + //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the + // printer will attempt to correct the error; errors + // smaller than this are ignored to minimize effects of + // measurement noise / latency (filter). + + #define I2CPE_ENC_2_ADDR I2CPE_PRESET_ADDR_Y // Same as above, but for encoder 2. + #define I2CPE_ENC_2_AXIS Y_AXIS + #define I2CPE_ENC_2_TYPE I2CPE_ENC_TYPE_LINEAR + #define I2CPE_ENC_2_TICKS_UNIT 2048 + //#define I2CPE_ENC_2_TICKS_REV (16 * 200) + //#define I2CPE_ENC_2_INVERT + #define I2CPE_ENC_2_EC_METHOD I2CPE_ECM_MICROSTEP + #define I2CPE_ENC_2_EC_THRESH 0.10 + + #define I2CPE_ENC_3_ADDR I2CPE_PRESET_ADDR_Z // Encoder 3. Add additional configuration options + #define I2CPE_ENC_3_AXIS Z_AXIS // as above, or use defaults below. + + #define I2CPE_ENC_4_ADDR I2CPE_PRESET_ADDR_E // Encoder 4. + #define I2CPE_ENC_4_AXIS E_AXIS + + #define I2CPE_ENC_5_ADDR 34 // Encoder 5. + #define I2CPE_ENC_5_AXIS E_AXIS + + // Default settings for encoders which are enabled, but without settings configured above. + #define I2CPE_DEF_TYPE I2CPE_ENC_TYPE_LINEAR + #define I2CPE_DEF_ENC_TICKS_UNIT 2048 + #define I2CPE_DEF_TICKS_REV (16 * 200) + #define I2CPE_DEF_EC_METHOD I2CPE_ECM_NONE + #define I2CPE_DEF_EC_THRESH 0.1 + + //#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given + // axis after which the printer will abort. Comment out to + // disable abort behaviour. + + #define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault + // for this amount of time (in ms) before the encoder + // is trusted again. + + /** + * Position is checked every time a new command is executed from the buffer but during long moves, + * this setting determines the minimum update time between checks. A value of 100 works well with + * error rolling average when attempting to correct only for skips and not for vibration. + */ + #define I2CPE_MIN_UPD_TIME_MS 4 // (ms) Minimum time between encoder checks. + + // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise. + #define I2CPE_ERR_ROLLING_AVERAGE + +#endif // I2C_POSITION_ENCODERS + +/** + * MAX7219 Debug Matrix + * + * Add support for a low-cost 8x8 LED Matrix based on the Max7219 chip, which can be used as a status + * display. Requires 3 signal wires. Some useful debug options are included to demonstrate its usage. + * + * Fully assembled MAX7219 boards can be found on the internet for under $2(US). + * For example, see https://www.ebay.com/sch/i.html?_nkw=332349290049 + */ +//#define MAX7219_DEBUG +#if ENABLED(MAX7219_DEBUG) + #define MAX7219_CLK_PIN 64 // 77 on Re-ARM // Configuration of the 3 pins to control the display + #define MAX7219_DIN_PIN 57 // 78 on Re-ARM + #define MAX7219_LOAD_PIN 44 // 79 on Re-ARM + + /** + * Sample debug features + * If you add more debug displays, be careful to avoid conflicts! + */ + #define MAX7219_DEBUG_PRINTER_ALIVE // Blink corner LED of 8x8 matrix to show that the firmware is functioning + #define MAX7219_DEBUG_STEPPER_HEAD 3 // Show the stepper queue head position on this and the next LED matrix row + #define MAX7219_DEBUG_STEPPER_TAIL 5 // Show the stepper queue tail position on this and the next LED matrix row + + #define MAX7219_DEBUG_STEPPER_QUEUE 0 // Show the current stepper queue depth on this and the next LED matrix row + // If you experience stuttering, reboots, etc. this option can reveal how + // tweaks made to the configuration are affecting the printer in real-time. +#endif + +/** + * NanoDLP Sync support + * + * Add support for Synchronized Z moves when using with NanoDLP. G0/G1 axis moves will output "Z_move_comp" + * string to enable synchronization with DLP projector exposure. This change will allow to use + * [[WaitForDoneMessage]] instead of populating your gcode with M400 commands + */ +//#define NANODLP_Z_SYNC +#if ENABLED(NANODLP_Z_SYNC) + //#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move. + // Default behaviour is limited to Z axis only. +#endif + +#endif // CONFIGURATION_ADV_H diff --git a/Marlin/src/config/examples/Creality/Ender-3/README.md b/Marlin/src/config/examples/Creality/Ender-3/README.md new file mode 100644 index 0000000000..e64f3ec3d2 --- /dev/null +++ b/Marlin/src/config/examples/Creality/Ender-3/README.md @@ -0,0 +1,18 @@ +# Creality Ender Support + +This branch is a reverse-engineered version based on the unpublished firmware from Creality. It is **not** the authoritative source, but has been carefully re-built by looking at their firmware and inferring the base version and configuration they used. The basis is the firmware version from "Jul 31 2017 10:16:30". It is based on Marlin 1.0.1, because + +* 1.0.0 had very different serial output in `setup()` and overall code structure. +* 1.0.2 changed the `VERSION_STRING` to include a leading space, and `lcd_init` uses `SET_INPUT` instead of `pinMode`. + +Configurations were found by seeing what code was compiled into the firmware, and constants used there. + +For U8Glib, at least version 1.14 and at most 1.17 is used, because + +* 1.12 didn't have the extra speed argument to u8g_InitCom. +* 1.13 didn't have the soft reset instruction for UC1701 initialization. +* 1.18 has a new directory structure. + +## Bitmaps + +The bootscreen and custom status screens come from Creality's firmware. diff --git a/Marlin/src/config/examples/Creality/Ender-3/_Bootscreen.h b/Marlin/src/config/examples/Creality/Ender-3/_Bootscreen.h new file mode 100644 index 0000000000..11be930e9c --- /dev/null +++ b/Marlin/src/config/examples/Creality/Ender-3/_Bootscreen.h @@ -0,0 +1,96 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ + +/** + * Custom Boot Screen bitmap + * + * Place this file in the root with your configuration files + * and enable SHOW_CUSTOM_BOOTSCREEN in Configuration.h. + * + * Use the Marlin Bitmap Converter to make your own: + * http://marlinfw.org/tools/u8glib/converter.html + */ + +#define CUSTOM_BOOTSCREEN_TIMEOUT 1000 +#define CUSTOM_BOOTSCREEN_BMPWIDTH 81 +#define CUSTOM_BOOTSCREEN_INVERTED + +const unsigned char custom_start_bmp[] PROGMEM = { + B11111111,B11111111,B11111111,B11111111,B11101111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111, + B11111111,B11111111,B11111111,B11111111,B11101111,B11101111,B11111111,B11111111,B11111111,B11111111,B11111111, + B11111111,B11111111,B11111111,B11111111,B11100111,B11011111,B11111111,B11111111,B11111111,B11111111,B11111111, + B11111111,B11111111,B11111111,B11111111,B11100111,B11011111,B11111111,B11111111,B11111111,B11111111,B11111111, + B11111111,B11111111,B11111111,B11111111,B11100011,B11011111,B11111111,B11111111,B11111111,B11111111,B11111111, + B11111111,B11111111,B11111111,B11111111,B11110011,B11001111,B11111111,B11111111,B11111111,B11111111,B11111111, + B11111111,B11111111,B11111111,B11100001,B11100001,B11001111,B11111111,B11111111,B11111111,B11111111,B11111111, + B11111111,B11111110,B01111000,B00000000,B00000000,B00000011,B11011101,B11111111,B11111111,B11111111,B11111111, + B11111110,B11111111,B10000000,B01111110,B00000000,B00000001,B11101110,B11111111,B11111111,B11111111,B11111111, + B11111110,B01111101,B11001111,B11111100,B00000000,B00000000,B11110111,B01111111,B11111111,B11111111,B11111111, + B11111111,B10001110,B00000110,B00000000,B00000000,B00000000,B01111011,B10111111,B11111111,B11111111,B11111111, + B11111111,B11000000,B00000000,B00000000,B00000000,B00000000,B01111101,B11011111,B11111111,B11111111,B11111111, + B11111111,B11111100,B00000001,B11111110,B00000000,B00000000,B00111110,B11100111,B11111111,B11111111,B11111111, + B11111111,B11111111,B11111111,B11111100,B00000000,B00000011,B00011111,B01110011,B11111111,B11111111,B11111111, + B11111111,B11111111,B11111111,B11111000,B00000000,B00000001,B10001111,B10000001,B11111111,B11111111,B11111111, + B11111111,B11111111,B11111111,B11100000,B00000000,B00000000,B10000011,B11111001,B11111111,B11111111,B11111111, + B11111111,B11111111,B11111111,B00000000,B11111100,B00000000,B00000000,B11110000,B11111111,B11111111,B11111111, + B11111111,B11111111,B11100000,B00001111,B11111111,B11000000,B00000000,B00000000,B11111111,B11111111,B11111111, + B11111111,B11111110,B00000011,B11111111,B11111111,B11000000,B00000000,B00000000,B11111111,B11111111,B11111111, + B11111111,B11111111,B11111111,B11111111,B11111001,B00000000,B00000000,B00000000,B11111111,B11111111,B11111111, + B11111111,B11111111,B11111111,B11111111,B11111100,B00000000,B00000111,B11000000,B11111111,B11111111,B11111111, + B11111111,B11111111,B11111111,B11111111,B11111111,B00000000,B00000111,B11100000,B11111111,B11111111,B11111111, + B11111111,B11111111,B11111111,B11111111,B11111111,B11100000,B00000111,B11110001,B11111111,B11111111,B11111111, + B11111111,B11111111,B11111111,B11111111,B11111111,B11111100,B00000111,B11111001,B11111111,B11111111,B11111111, + B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B00000011,B11111001,B11111111,B11111111,B11111111, + B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B10000011,B11111001,B11111111,B11111111,B11111111, + B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11000011,B11111111,B11111111,B11111111,B11111111, + B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11100001,B11111111,B11111111,B11111111,B11111111, + B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11110000,B10111111,B11111111,B11111111,B11111111, + B11111111,B11111111,B11111111,B11111111,B11111111,B11111011,B11111000,B00111111,B11111111,B11111111,B11111111, + B11111111,B11111111,B11111111,B11111111,B11111111,B11111001,B11111000,B00111111,B11111111,B11111111,B11111111, + B11111111,B11111111,B11111111,B11111111,B11111111,B01111110,B11110000,B11111111,B11111111,B11111111,B11111111, + B11111111,B11111111,B11111111,B11111111,B11111111,B10001110,B00000011,B11111111,B11111111,B11111111,B11111111, + B11111111,B11111111,B11111111,B11111111,B11111111,B11100000,B00011111,B11111111,B11111111,B11111111,B11111111, + B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111, + B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111, + B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B01111111,B11111111,B11111111,B11111111, + B11111111,B00000000,B00000000,B01111111,B11111111,B11111111,B11111000,B01111111,B11111111,B11111111,B11111111, + B11111111,B10000000,B00000000,B01111111,B11111111,B11111111,B11100000,B01111111,B11111111,B11111111,B11111111, + B11111111,B11000011,B11111100,B11111111,B11111111,B11111111,B11111000,B11111111,B11111111,B11111111,B11111111, + B11111111,B11000011,B11111100,B11111111,B11111111,B11111111,B11111000,B11111111,B11111111,B11111111,B11111111, + B11111111,B10000111,B11111101,B11111111,B11111111,B11111111,B11110001,B11111111,B11111111,B11111111,B11111111, + B11111111,B10000111,B11111111,B11111111,B11111111,B11111111,B11110001,B11111111,B11111111,B11111111,B11111111, + B11111111,B00001111,B11100111,B11110011,B00001111,B11111100,B00100011,B11111100,B00111111,B11111111,B11111111, + B11111111,B00001111,B11101111,B10000000,B00000111,B11110000,B00000011,B11110000,B00011110,B00000000,B01111111, + B11111110,B00011111,B11001111,B10000001,B10000111,B11000111,B10000111,B11000111,B00001100,B00000000,B01111111, + B11111110,B00000000,B00011111,B11000111,B11000111,B10001111,B11000111,B10011111,B00001111,B00001100,B11111111, + B11111110,B00000000,B00011111,B10000111,B10001111,B00011111,B10001111,B00011111,B00001111,B00011111,B11111111, + B11111100,B00111111,B10011111,B10001111,B10001111,B00011111,B10001110,B00000000,B00011110,B00111111,B11111111, + B11111100,B01111111,B00111111,B00001111,B00011110,B00111111,B00011110,B00111111,B11111110,B00111111,B11111111, + B11111000,B01111111,B11111111,B00011111,B00011100,B00111111,B00011100,B01111111,B11111100,B01111111,B11111111, + B11111000,B11111111,B11111111,B00011110,B00011100,B01111110,B00011100,B01111111,B11111100,B01111111,B11111111, + B11110000,B11111111,B11001110,B00111110,B00111100,B01111110,B00111100,B01111111,B10111000,B11111111,B11111111, + B11110000,B11111111,B10011110,B00111100,B00111000,B01111100,B00111000,B01111110,B01111000,B11111111,B11111111, + B11100001,B11111111,B00111100,B01111100,B01111000,B01111100,B01111000,B00111100,B11110001,B11111111,B11111111, + B11100001,B11111000,B00111000,B01111000,B01111000,B00010000,B00011000,B00000001,B11110001,B11111111,B11111111, + B00000000,B00000000,B01100000,B00100000,B00111100,B00000000,B01111100,B00000111,B10000000,B01111111,B11111111, + B11111111,B11111111,B11111111,B11111111,B11111110,B00011111,B11111110,B00011111,B11111111,B11111111,B11111111 +}; diff --git a/Marlin/src/config/examples/Creality/Ender-3/_Statusscreen.h b/Marlin/src/config/examples/Creality/Ender-3/_Statusscreen.h new file mode 100644 index 0000000000..95e8298c3e --- /dev/null +++ b/Marlin/src/config/examples/Creality/Ender-3/_Statusscreen.h @@ -0,0 +1,130 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ + +/** + * Custom Status Screen bitmap + * + * Place this file in the root with your configuration files + * and enable CUSTOM_STATUS_SCREEN_IMAGE in Configuration.h. + * + * Use the Marlin Bitmap Converter to make your own: + * http://marlinfw.org/tools/u8glib/converter.html + */ + +#define STATUS_SCREENWIDTH 128 +#define STATUS_SCREEN_HOTEND_TEXT_X(E) (38 + (E) * 20) +#define STATUS_SCREEN_BED_TEXT_X (HOTENDS > 1 ? 81 : 73) +#define STATUS_SCREEN_FAN_TEXT_X 103 + +//============================================ + +#if HOTENDS < 2 + + const unsigned char status_screen0_bmp[] PROGMEM = { + B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111111,B11111111,B11110000, + B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111000,B00000000,B01110000, + B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00110000,B11111100,B00110000, + B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00100000,B11111100,B00010000, + B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00100000,B01111000,B00010000, + B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00100000,B00110000,B00010000, + B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00101100,B00000000,B11010000, + B11111000,B00000001,B10000000,B00000000,B00001100,B00011111,B11100000,B00000000,B00000000,B00001000,B00100000,B10000000,B00000000,B00101110,B00110001,B11010000, + B01001000,B00000000,B10000000,B00000000,B00010010,B00111111,B11110000,B00000000,B00000000,B00000100,B00010000,B01000000,B00000000,B00101111,B01111011,B11010000, + B01000011,B11000011,B10001100,B11010000,B00000010,B00111111,B11110000,B00000000,B00000000,B00000100,B00010000,B01000000,B00000000,B00101111,B01111011,B11010000, + B01110001,B00100100,B10010010,B01100111,B11001100,B00111111,B11110000,B00000000,B00000000,B00001000,B00100000,B10000000,B00000000,B00101110,B00110001,B11010000, + B01000001,B00100100,B10011110,B01000000,B00000010,B00011111,B11100000,B00000000,B00000000,B00010000,B01000001,B00000000,B00000000,B00101100,B00000000,B11010000, + B01001001,B00100100,B10010000,B01000000,B00010010,B00011111,B11100000,B00000000,B00000000,B00100000,B10000010,B00000000,B00000000,B00100000,B00110000,B00010000, + B11111011,B10110011,B11001110,B11100000,B00001100,B00111111,B11110000,B00000000,B00000000,B00100000,B10000010,B00000000,B00000000,B00100000,B01111000,B00010000, + B00000000,B00000000,B00000000,B00000000,B00000000,B00111111,B11110000,B00000000,B00000000,B00010000,B01000001,B00000000,B00000000,B00100000,B11111100,B00010000, + B00000000,B00000000,B00000000,B00000000,B00000000,B00111111,B11110000,B00000000,B00000000,B00001000,B00100000,B10000000,B00000000,B00110000,B11111100,B00110000, + B00000000,B00000000,B00000000,B00000000,B00000000,B00001111,B11000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111000,B00000000,B01110000, + B00000000,B00000000,B00000000,B00000000,B00000000,B00000111,B10000000,B00000000,B00000000,B11111111,B11111111,B11000000,B00000000,B00111111,B11111111,B11110000, + B00000000,B00000000,B00000000,B00000000,B00000000,B00000011,B00000000,B00000000,B00000000,B11111111,B11111111,B11000000,B00000000,B00000000,B00000000,B00000000 + }; + const unsigned char status_screen1_bmp[] PROGMEM = { + B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111111,B11111111,B11110000, + B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111000,B00000000,B01110000, + B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00110011,B10000111,B00110000, + B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00100111,B10000111,B10010000, + B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00101111,B10000111,B11010000, + B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00101111,B10000111,B11010000, + B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00101111,B00000011,B11010000, + B11111000,B00000001,B10000000,B00000000,B00001100,B00011111,B11100000,B00000000,B00000000,B00001000,B00100000,B10000000,B00000000,B00100000,B00110000,B00010000, + B01001000,B00000000,B10000000,B00000000,B00010010,B00111111,B11110000,B00000000,B00000000,B00000100,B00010000,B01000000,B00000000,B00100000,B01111000,B00010000, + B01000011,B11000011,B10001100,B11010000,B00000010,B00111111,B11110000,B00000000,B00000000,B00000100,B00010000,B01000000,B00000000,B00100000,B01111000,B00010000, + B01110001,B00100100,B10010010,B01100111,B11001100,B00111111,B11110000,B00000000,B00000000,B00001000,B00100000,B10000000,B00000000,B00100000,B00110000,B00010000, + B01000001,B00100100,B10011110,B01000000,B00000010,B00011111,B11100000,B00000000,B00000000,B00010000,B01000001,B00000000,B00000000,B00101111,B00000011,B11010000, + B01001001,B00100100,B10010000,B01000000,B00010010,B00011111,B11100000,B00000000,B00000000,B00100000,B10000010,B00000000,B00000000,B00101111,B10000111,B11010000, + B11111011,B10110011,B11001110,B11100000,B00001100,B00111111,B11110000,B00000000,B00000000,B00100000,B10000010,B00000000,B00000000,B00101111,B10000111,B11010000, + B00000000,B00000000,B00000000,B00000000,B00000000,B00111111,B11110000,B00000000,B00000000,B00010000,B01000001,B00000000,B00000000,B00100111,B10000111,B10010000, + B00000000,B00000000,B00000000,B00000000,B00000000,B00111111,B11110000,B00000000,B00000000,B00001000,B00100000,B10000000,B00000000,B00110011,B10000111,B00110000, + B00000000,B00000000,B00000000,B00000000,B00000000,B00001111,B11000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111000,B00000000,B01110000, + B00000000,B00000000,B00000000,B00000000,B00000000,B00000111,B10000000,B00000000,B00000000,B11111111,B11111111,B11000000,B00000000,B00111111,B11111111,B11110000, + B00000000,B00000000,B00000000,B00000000,B00000000,B00000011,B00000000,B00000000,B00000000,B11111111,B11111111,B11000000,B00000000,B00000000,B00000000,B00000000 + }; + +#else // HOTENDS >= 2 + + const unsigned char status_screen0_bmp[] PROGMEM = { + B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111111,B11111111,B11110000, + B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111000,B00000000,B01110000, + B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00110000,B11111100,B00110000, + B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00100000,B11111100,B00010000, + B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00100000,B01111000,B00010000, + B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00100000,B00110000,B00010000, + B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00101100,B00000000,B11010000, + B11111000,B00000001,B10000000,B00000000,B00001100,B00011111,B11100000,B00000001,B11111110,B00000000,B00001000,B00100000,B10000000,B00101110,B00110001,B11010000, + B01001000,B00000000,B10000000,B00000000,B00010010,B00111110,B11110000,B00000011,B11001111,B00000000,B00000100,B00010000,B01000000,B00101111,B01111011,B11010000, + B01000011,B11000011,B10001100,B11010000,B00000010,B00111100,B11110000,B00000011,B10110111,B00000000,B00000100,B00010000,B01000000,B00101111,B01111011,B11010000, + B01110001,B00100100,B10010010,B01100111,B11001100,B00111010,B11110000,B00000011,B11110111,B00000000,B00001000,B00100000,B10000000,B00101110,B00110001,B11010000, + B01000001,B00100100,B10011110,B01000000,B00000010,B00011110,B11100000,B00000001,B11101110,B00000000,B00010000,B01000001,B00000000,B00101100,B00000000,B11010000, + B01001001,B00100100,B10010000,B01000000,B00010010,B00011110,B11100000,B00000001,B11011110,B00000000,B00100000,B10000010,B00000000,B00100000,B00110000,B00010000, + B11111011,B10110011,B11001110,B11100000,B00001100,B00111110,B11110000,B00000011,B10111111,B00000000,B00100000,B10000010,B00000000,B00100000,B01111000,B00010000, + B00000000,B00000000,B00000000,B00000000,B00000000,B00111110,B11110000,B00000011,B10000111,B00000000,B00010000,B01000001,B00000000,B00100000,B11111100,B00010000, + B00000000,B00000000,B00000000,B00000000,B00000000,B00111111,B11110000,B00000011,B11111111,B00000000,B00001000,B00100000,B10000000,B00110000,B11111100,B00110000, + B00000000,B00000000,B00000000,B00000000,B00000000,B00001111,B11000000,B00000000,B11111100,B00000000,B00000000,B00000000,B00000000,B00111000,B00000000,B01110000, + B00000000,B00000000,B00000000,B00000000,B00000000,B00000111,B10000000,B00000000,B01111000,B00000000,B11111111,B11111111,B11000000,B00111111,B11111111,B11110000, + B00000000,B00000000,B00000000,B00000000,B00000000,B00000011,B00000000,B00000000,B00110000,B00000000,B11111111,B11111111,B11000000,B00000000,B00000000,B00000000 + }; + const unsigned char status_screen1_bmp[] PROGMEM = { + B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111111,B11111111,B11110000, + B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111000,B00000000,B01110000, + B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00110011,B10000111,B00110000, + B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00100111,B10000111,B10010000, + B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00101111,B10000111,B11010000, + B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00101111,B10000111,B11010000, + B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00101111,B00000011,B11010000, + B11111000,B00000001,B10000000,B00000000,B00001100,B00011111,B11100000,B00000001,B11111110,B00000000,B00001000,B00100000,B10000000,B00100000,B00110000,B00010000, + B01001000,B00000000,B10000000,B00000000,B00010010,B00111110,B11110000,B00000011,B11001111,B00000000,B00000100,B00010000,B01000000,B00100000,B01111000,B00010000, + B01000011,B11000011,B10001100,B11010000,B00000010,B00111100,B11110000,B00000011,B10110111,B00000000,B00000100,B00010000,B01000000,B00100000,B01111000,B00010000, + B01110001,B00100100,B10010010,B01100111,B11001100,B00111010,B11110000,B00000011,B11110111,B00000000,B00001000,B00100000,B10000000,B00100000,B00110000,B00010000, + B01000001,B00100100,B10011110,B01000000,B00000010,B00011110,B11100000,B00000001,B11101110,B00000000,B00010000,B01000001,B00000000,B00101111,B00000011,B11010000, + B01001001,B00100100,B10010000,B01000000,B00010010,B00011110,B11100000,B00000001,B11011110,B00000000,B00100000,B10000010,B00000000,B00101111,B10000111,B11010000, + B11111011,B10110011,B11001110,B11100000,B00001100,B00111110,B11110000,B00000011,B10111111,B00000000,B00100000,B10000010,B00000000,B00101111,B10000111,B11010000, + B00000000,B00000000,B00000000,B00000000,B00000000,B00111110,B11110000,B00000011,B10000111,B00000000,B00010000,B01000001,B00000000,B00100111,B10000111,B10010000, + B00000000,B00000000,B00000000,B00000000,B00000000,B00111111,B11110000,B00000011,B11111111,B00000000,B00001000,B00100000,B10000000,B00110011,B10000111,B00110000, + B00000000,B00000000,B00000000,B00000000,B00000000,B00001111,B11000000,B00000000,B11111100,B00000000,B00000000,B00000000,B00000000,B00111000,B00000000,B01110000, + B00000000,B00000000,B00000000,B00000000,B00000000,B00000111,B10000000,B00000000,B01111000,B00000000,B11111111,B11111111,B11000000,B00111111,B11111111,B11110000, + B00000000,B00000000,B00000000,B00000000,B00000000,B00000011,B00000000,B00000000,B00110000,B00000000,B11111111,B11111111,B11000000,B00000000,B00000000,B00000000 + }; + +#endif // HOTENDS >= 2