MBL: Apply https://github.com/MarlinFirmware/Marlin/pull/3903 to example_configurations

Marlin/example_configurations/Felix/Configuration.h

@@ -501,10 +501,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 //#define MESH_BED_LEVELING    // Enable mesh bed leveling.
 
 #if ENABLED(MESH_BED_LEVELING)
-  #define MESH_MIN_X 10
+  #define MESH_INSET 10        // Mesh inset margin on print area
-  #define MESH_MAX_X (X_MAX_POS - (MESH_MIN_X))
-  #define MESH_MIN_Y 10
-  #define MESH_MAX_Y (Y_MAX_POS - (MESH_MIN_Y))
   #define MESH_NUM_X_POINTS 3  // Don't use more than 7 points per axis, implementation limited.
   #define MESH_NUM_Y_POINTS 3
   #define MESH_HOME_SEARCH_Z 4  // Z after Home, bed somewhere below but above 0.0.

Marlin/example_configurations/Felix/DUAL/Configuration.h

@@ -499,10 +499,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 //#define MESH_BED_LEVELING    // Enable mesh bed leveling.
 
 #if ENABLED(MESH_BED_LEVELING)
-  #define MESH_MIN_X 10
+  #define MESH_INSET 10        // Mesh inset margin on print area
-  #define MESH_MAX_X (X_MAX_POS - (MESH_MIN_X))
-  #define MESH_MIN_Y 10
-  #define MESH_MAX_Y (Y_MAX_POS - (MESH_MIN_Y))
   #define MESH_NUM_X_POINTS 3  // Don't use more than 7 points per axis, implementation limited.
   #define MESH_NUM_Y_POINTS 3
   #define MESH_HOME_SEARCH_Z 4  // Z after Home, bed somewhere below but above 0.0.

Marlin/example_configurations/Hephestos/Configuration.h

@@ -511,10 +511,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 //#define MESH_BED_LEVELING    // Enable mesh bed leveling.
 
 #if ENABLED(MESH_BED_LEVELING)
-  #define MESH_MIN_X 10
+  #define MESH_INSET 10        // Mesh inset margin on print area
-  #define MESH_MAX_X (X_MAX_POS - (MESH_MIN_X))
-  #define MESH_MIN_Y 10
-  #define MESH_MAX_Y (Y_MAX_POS - (MESH_MIN_Y))
   #define MESH_NUM_X_POINTS 3  // Don't use more than 7 points per axis, implementation limited.
   #define MESH_NUM_Y_POINTS 3
   #define MESH_HOME_SEARCH_Z 4  // Z after Home, bed somewhere below but above 0.0.

Marlin/example_configurations/Hephestos_2/Configuration.h

@@ -513,10 +513,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 //#define MESH_BED_LEVELING    // Enable mesh bed leveling.
 
 #if ENABLED(MESH_BED_LEVELING)
-  #define MESH_MIN_X 10
+  #define MESH_INSET 10        // Mesh inset margin on print area
-  #define MESH_MAX_X (X_MAX_POS - (MESH_MIN_X))
-  #define MESH_MIN_Y 10
-  #define MESH_MAX_Y (Y_MAX_POS - (MESH_MIN_Y))
   #define MESH_NUM_X_POINTS 3  // Don't use more than 7 points per axis, implementation limited.
   #define MESH_NUM_Y_POINTS 3
   #define MESH_HOME_SEARCH_Z 4  // Z after Home, bed somewhere below but above 0.0.

Marlin/example_configurations/K8200/Configuration.h

@@ -536,10 +536,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 //#define MESH_BED_LEVELING    // Enable mesh bed leveling.
 
 #if ENABLED(MESH_BED_LEVELING)
-  #define MESH_MIN_X 10
+  #define MESH_INSET 10        // Mesh inset margin on print area
-  #define MESH_MAX_X (X_MAX_POS - (MESH_MIN_X))
-  #define MESH_MIN_Y 10
-  #define MESH_MAX_Y (Y_MAX_POS - (MESH_MIN_Y))
   #define MESH_NUM_X_POINTS 3  // Don't use more than 7 points per axis, implementation limited.
   #define MESH_NUM_Y_POINTS 3
   #define MESH_HOME_SEARCH_Z 4  // Z after Home, bed somewhere below but above 0.0.

Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h

@@ -519,10 +519,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 //#define MESH_BED_LEVELING    // Enable mesh bed leveling.
 
 #if ENABLED(MESH_BED_LEVELING)
-  #define MESH_MIN_X 10
+  #define MESH_INSET 10        // Mesh inset margin on print area
-  #define MESH_MAX_X (X_MAX_POS - (MESH_MIN_X))
-  #define MESH_MIN_Y 10
-  #define MESH_MAX_Y (Y_MAX_POS - (MESH_MIN_Y))
   #define MESH_NUM_X_POINTS 3  // Don't use more than 7 points per axis, implementation limited.
   #define MESH_NUM_Y_POINTS 3
   #define MESH_HOME_SEARCH_Z 4  // Z after Home, bed somewhere below but above 0.0.

Marlin/example_configurations/RigidBot/Configuration.h

@@ -513,10 +513,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 //#define MESH_BED_LEVELING    // Enable mesh bed leveling.
 
 #if ENABLED(MESH_BED_LEVELING)
-  #define MESH_MIN_X 10
+  #define MESH_INSET 10        // Mesh inset margin on print area
-  #define MESH_MAX_X (X_MAX_POS - (MESH_MIN_X))
-  #define MESH_MIN_Y 10
-  #define MESH_MAX_Y (Y_MAX_POS - (MESH_MIN_Y))
   #define MESH_NUM_X_POINTS 3  // Don't use more than 7 points per axis, implementation limited.
   #define MESH_NUM_Y_POINTS 3
   #define MESH_HOME_SEARCH_Z 4  // Z after Home, bed somewhere below but above 0.0.

Marlin/example_configurations/SCARA/Configuration.h

@@ -527,10 +527,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 //#define MESH_BED_LEVELING    // Enable mesh bed leveling.
 
 #if ENABLED(MESH_BED_LEVELING)
-  #define MESH_MIN_X 10
+  #define MESH_INSET 10        // Mesh inset margin on print area
-  #define MESH_MAX_X (X_MAX_POS - (MESH_MIN_X))
-  #define MESH_MIN_Y 10
-  #define MESH_MAX_Y (Y_MAX_POS - (MESH_MIN_Y))
   #define MESH_NUM_X_POINTS 3  // Don't use more than 7 points per axis, implementation limited.
   #define MESH_NUM_Y_POINTS 3
   #define MESH_HOME_SEARCH_Z 4  // Z after Home, bed somewhere below but above 0.0.

Marlin/example_configurations/TAZ4/Configuration.h

@@ -540,10 +540,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 //#define MESH_BED_LEVELING    // Enable mesh bed leveling.
 
 #if ENABLED(MESH_BED_LEVELING)
-  #define MESH_MIN_X 10
+  #define MESH_INSET 10        // Mesh inset margin on print area
-  #define MESH_MAX_X (X_MAX_POS - (MESH_MIN_X))
-  #define MESH_MIN_Y 10
-  #define MESH_MAX_Y (Y_MAX_POS - (MESH_MIN_Y))
   #define MESH_NUM_X_POINTS 3  // Don't use more than 7 points per axis, implementation limited.
   #define MESH_NUM_Y_POINTS 3
   #define MESH_HOME_SEARCH_Z 4  // Z after Home, bed somewhere below but above 0.0.

Marlin/example_configurations/WITBOX/Configuration.h

@@ -511,10 +511,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 //#define MESH_BED_LEVELING    // Enable mesh bed leveling.
 
 #if ENABLED(MESH_BED_LEVELING)
-  #define MESH_MIN_X 10
+  #define MESH_INSET 10        // Mesh inset margin on print area
-  #define MESH_MAX_X (X_MAX_POS - (MESH_MIN_X))
-  #define MESH_MIN_Y 10
-  #define MESH_MAX_Y (Y_MAX_POS - (MESH_MIN_Y))
   #define MESH_NUM_X_POINTS 3  // Don't use more than 7 points per axis, implementation limited.
   #define MESH_NUM_Y_POINTS 3
   #define MESH_HOME_SEARCH_Z 4  // Z after Home, bed somewhere below but above 0.0.

Marlin/example_configurations/adafruit/ST7565/Configuration.h

@@ -519,10 +519,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 //#define MESH_BED_LEVELING    // Enable mesh bed leveling.
 
 #if ENABLED(MESH_BED_LEVELING)
-  #define MESH_MIN_X 10
+  #define MESH_INSET 10        // Mesh inset margin on print area
-  #define MESH_MAX_X (X_MAX_POS - (MESH_MIN_X))
-  #define MESH_MIN_Y 10
-  #define MESH_MAX_Y (Y_MAX_POS - (MESH_MIN_Y))
   #define MESH_NUM_X_POINTS 3  // Don't use more than 7 points per axis, implementation limited.
   #define MESH_NUM_Y_POINTS 3
   #define MESH_HOME_SEARCH_Z 4  // Z after Home, bed somewhere below but above 0.0.

Marlin/example_configurations/delta/biv2.5/Configuration.h

@@ -561,10 +561,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 //#define MESH_BED_LEVELING    // Enable mesh bed leveling.
 
 #if ENABLED(MESH_BED_LEVELING)
-  #define MESH_MIN_X 10
+  #define MESH_INSET 10        // Mesh inset margin on print area
-  #define MESH_MAX_X (X_MAX_POS - (MESH_MIN_X))
-  #define MESH_MIN_Y 10
-  #define MESH_MAX_Y (Y_MAX_POS - (MESH_MIN_Y))
   #define MESH_NUM_X_POINTS 3  // Don't use more than 7 points per axis, implementation limited.
   #define MESH_NUM_Y_POINTS 3
   #define MESH_HOME_SEARCH_Z 4  // Z after Home, bed somewhere below but above 0.0.

Marlin/example_configurations/delta/generic/Configuration.h

@@ -561,10 +561,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 //#define MESH_BED_LEVELING    // Enable mesh bed leveling.
 
 #if ENABLED(MESH_BED_LEVELING)
-  #define MESH_MIN_X 10
+  #define MESH_INSET 10        // Mesh inset margin on print area
-  #define MESH_MAX_X (X_MAX_POS - (MESH_MIN_X))
-  #define MESH_MIN_Y 10
-  #define MESH_MAX_Y (Y_MAX_POS - (MESH_MIN_Y))
   #define MESH_NUM_X_POINTS 3  // Don't use more than 7 points per axis, implementation limited.
   #define MESH_NUM_Y_POINTS 3
   #define MESH_HOME_SEARCH_Z 4  // Z after Home, bed somewhere below but above 0.0.

Marlin/example_configurations/delta/kossel_mini/Configuration.h

@@ -561,10 +561,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 //#define MESH_BED_LEVELING    // Enable mesh bed leveling.
 
 #if ENABLED(MESH_BED_LEVELING)
-  #define MESH_MIN_X 10
+  #define MESH_INSET 10        // Mesh inset margin on print area
-  #define MESH_MAX_X (X_MAX_POS - (MESH_MIN_X))
-  #define MESH_MIN_Y 10
-  #define MESH_MAX_Y (Y_MAX_POS - (MESH_MIN_Y))
   #define MESH_NUM_X_POINTS 3  // Don't use more than 7 points per axis, implementation limited.
   #define MESH_NUM_Y_POINTS 3
   #define MESH_HOME_SEARCH_Z 4  // Z after Home, bed somewhere below but above 0.0.

Marlin/example_configurations/delta/kossel_pro/Configuration.h

@@ -550,10 +550,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 //#define MESH_BED_LEVELING    // Enable mesh bed leveling.
 
 #if ENABLED(MESH_BED_LEVELING)
-  #define MESH_MIN_X 10
+  #define MESH_INSET 10        // Mesh inset margin on print area
-  #define MESH_MAX_X (X_MAX_POS - (MESH_MIN_X))
-  #define MESH_MIN_Y 10
-  #define MESH_MAX_Y (Y_MAX_POS - (MESH_MIN_Y))
   #define MESH_NUM_X_POINTS 3  // Don't use more than 7 points per axis, implementation limited.
   #define MESH_NUM_Y_POINTS 3
   #define MESH_HOME_SEARCH_Z 4  // Z after Home, bed somewhere below but above 0.0.

Marlin/example_configurations/delta/kossel_xl/Configuration.h

@@ -559,10 +559,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 //#define MESH_BED_LEVELING    // Enable mesh bed leveling.
 
 #if ENABLED(MESH_BED_LEVELING)
-  #define MESH_MIN_X 10
+  #define MESH_INSET 10        // Mesh inset margin on print area
-  #define MESH_MAX_X (X_MAX_POS - (MESH_MIN_X))
-  #define MESH_MIN_Y 10
-  #define MESH_MAX_Y (Y_MAX_POS - (MESH_MIN_Y))
   #define MESH_NUM_X_POINTS 3  // Don't use more than 7 points per axis, implementation limited.
   #define MESH_NUM_Y_POINTS 3
   #define MESH_HOME_SEARCH_Z 4  // Z after Home, bed somewhere below but above 0.0.

Marlin/example_configurations/makibox/Configuration.h

@@ -522,10 +522,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 //#define MESH_BED_LEVELING    // Enable mesh bed leveling.
 
 #if ENABLED(MESH_BED_LEVELING)
-  #define MESH_MIN_X 10
+  #define MESH_INSET 10        // Mesh inset margin on print area
-  #define MESH_MAX_X (X_MAX_POS - (MESH_MIN_X))
-  #define MESH_MIN_Y 10
-  #define MESH_MAX_Y (Y_MAX_POS - (MESH_MIN_Y))
   #define MESH_NUM_X_POINTS 3  // Don't use more than 7 points per axis, implementation limited.
   #define MESH_NUM_Y_POINTS 3
   #define MESH_HOME_SEARCH_Z 4  // Z after Home, bed somewhere below but above 0.0.

Marlin/example_configurations/tvrrug/Round2/Configuration.h

@@ -509,10 +509,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 //#define MESH_BED_LEVELING    // Enable mesh bed leveling.
 
 #if ENABLED(MESH_BED_LEVELING)
-  #define MESH_MIN_X 10
+  #define MESH_INSET 10        // Mesh inset margin on print area
-  #define MESH_MAX_X (X_MAX_POS - (MESH_MIN_X))
-  #define MESH_MIN_Y 10
-  #define MESH_MAX_Y (Y_MAX_POS - (MESH_MIN_Y))
   #define MESH_NUM_X_POINTS 3  // Don't use more than 7 points per axis, implementation limited.
   #define MESH_NUM_Y_POINTS 3
   #define MESH_HOME_SEARCH_Z 4  // Z after Home, bed somewhere below but above 0.0.