diff --git a/Marlin/src/lcd/menu/menu.h b/Marlin/src/lcd/menu/menu.h index da1b9a7a73..77e1e4a749 100644 --- a/Marlin/src/lcd/menu/menu.h +++ b/Marlin/src/lcd/menu/menu.h @@ -57,7 +57,7 @@ DECLARE_MENU_EDIT_TYPE(uint16_t, uint16_5, ui16tostr5, 0.01 ); // 123 DECLARE_MENU_EDIT_TYPE(float, float3, ftostr3, 1 ); // 123 right-justified DECLARE_MENU_EDIT_TYPE(float, float52, ftostr42_52, 100 ); // _2.34, 12.34, -2.34 or 123.45, -23.45 DECLARE_MENU_EDIT_TYPE(float, float43, ftostr43sign, 1000 ); // 1.234 -DECLARE_MENU_EDIT_TYPE(float, float5, ftostr5rj, 0.01f ); // 12345 right-justified +DECLARE_MENU_EDIT_TYPE(float, float5, ftostr5rj, 1 ); // 12345 right-justified DECLARE_MENU_EDIT_TYPE(float, float5_25, ftostr5rj, 0.04f ); // 12345 right-justified (25 increment) DECLARE_MENU_EDIT_TYPE(float, float51, ftostr51rj, 10 ); // 1234.5 right-justified DECLARE_MENU_EDIT_TYPE(float, float51sign, ftostr51sign, 10 ); // +1234.5 diff --git a/Marlin/src/pins/stm32/pins_FYSETC_AIO_II.h b/Marlin/src/pins/stm32/pins_FYSETC_AIO_II.h index 5d30aaec31..51372398da 100644 --- a/Marlin/src/pins/stm32/pins_FYSETC_AIO_II.h +++ b/Marlin/src/pins/stm32/pins_FYSETC_AIO_II.h @@ -35,6 +35,14 @@ // Ignore temp readings during development. //#define BOGUS_TEMPERATURE_GRACE_PERIOD 2000 +// +// Flash EEPROM Emulation +// +#define FLASH_EEPROM_EMULATION +#define EEPROM_PAGE_SIZE uint16(0x800) // 2KB +#define EEPROM_START_ADDRESS uint32(0x8000000 + 256 * 1024 - 2 * EEPROM_PAGE_SIZE) +#undef E2END +#define E2END (EEPROM_PAGE_SIZE - 1) // 2KB // // Limit Switches // diff --git a/config/examples/FYSETC/AIO_II/Configuration.h b/config/examples/FYSETC/AIO_II/Configuration.h index 3b3797d915..19b5ca3dd6 100644 --- a/config/examples/FYSETC/AIO_II/Configuration.h +++ b/config/examples/FYSETC/AIO_II/Configuration.h @@ -641,9 +641,9 @@ #endif // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup). -#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop. -#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop. -#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop. +#define X_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop. +#define Y_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop. +#define Z_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop. #define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop. #define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop. #define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop. @@ -721,7 +721,7 @@ * Override with M92 * X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]] */ -#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 400, 93 } +#define DEFAULT_AXIS_STEPS_PER_UNIT { 640, 640, 3200, 800 } /** * Default Max Feed Rate (mm/s) @@ -989,10 +989,10 @@ // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } -#define X_ENABLE_ON 0 -#define Y_ENABLE_ON 0 -#define Z_ENABLE_ON 0 -#define E_ENABLE_ON 0 // For all extruders +#define X_ENABLE_ON 1 +#define Y_ENABLE_ON 1 +#define Z_ENABLE_ON 1 +#define E_ENABLE_ON 1 // For all extruders // Disables axis stepper immediately when it's not being used. // WARNING: When motors turn off there is a chance of losing position accuracy! diff --git a/config/examples/FYSETC/AIO_II/Configuration_adv.h b/config/examples/FYSETC/AIO_II/Configuration_adv.h index 72c44aabaa..00d732fbb5 100644 --- a/config/examples/FYSETC/AIO_II/Configuration_adv.h +++ b/config/examples/FYSETC/AIO_II/Configuration_adv.h @@ -165,13 +165,13 @@ * Thermal Protection parameters for the bed are just as above for hotends. */ #if ENABLED(THERMAL_PROTECTION_BED) - #define THERMAL_PROTECTION_BED_PERIOD 60 // Seconds + #define THERMAL_PROTECTION_BED_PERIOD 20 // Seconds #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius /** * As described above, except for the bed (M140/M190/M303). */ - #define WATCH_BED_TEMP_PERIOD 100 // Seconds + #define WATCH_BED_TEMP_PERIOD 60 // Seconds #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #endif @@ -924,7 +924,7 @@ //#define MENU_ADDAUTOSTART // Add a menu option to run auto#.g files - #define EVENT_GCODE_SD_STOP "M21" // G-code to run on Stop Print (e.g., "G28XY" or "G27") + #define EVENT_GCODE_SD_STOP "G28XY" // G-code to run on Stop Print (e.g., "G28XY" or "G27") /** * Continue after Power-Loss (Creality3D) @@ -1860,13 +1860,13 @@ * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 - #define Y_SLAVE_ADDRESS 1 - #define Z_SLAVE_ADDRESS 2 + #define Y_SLAVE_ADDRESS 0 + #define Z_SLAVE_ADDRESS 0 #define X2_SLAVE_ADDRESS 0 #define Y2_SLAVE_ADDRESS 0 #define Z2_SLAVE_ADDRESS 0 #define Z3_SLAVE_ADDRESS 0 - #define E0_SLAVE_ADDRESS 3 + #define E0_SLAVE_ADDRESS 0 #define E1_SLAVE_ADDRESS 0 #define E2_SLAVE_ADDRESS 0 #define E3_SLAVE_ADDRESS 0 diff --git a/config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration.h b/config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration.h index 5ce77ea0d2..14627a346c 100644 --- a/config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration.h +++ b/config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration.h @@ -338,7 +338,6 @@ //#define AUTO_POWER_CHAMBER_TEMP 30 // (°C) Turn on PSU over this temperature #define POWER_TIMEOUT 30 #endif - #endif // @section temperature @@ -2096,7 +2095,7 @@ // Use software PWM to drive the fan, as for the heaters. This uses a very low frequency // which is not as annoying as with the hardware PWM. On the other hand, if this frequency // is too low, you should also increment SOFT_PWM_SCALE. -//#define FAN_SOFT_PWM +#define FAN_SOFT_PWM // Incrementing this by 1 will double the software PWM frequency, // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. diff --git a/config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration_adv.h b/config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration_adv.h index 3fa6748c1c..e838f50494 100644 --- a/config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration_adv.h +++ b/config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration_adv.h @@ -1904,7 +1904,7 @@ * Define you own with * { , , hysteresis_start[1..8] } */ - #define CHOPPER_TIMING CHOPPER_DEFAULT_12V + #define CHOPPER_TIMING CHOPPER_DEFAULT_24V /** * Monitor Trinamic drivers for error conditions, diff --git a/config/examples/FYSETC/Cheetah 1.2/base/Configuration.h b/config/examples/FYSETC/Cheetah 1.2/base/Configuration.h index db87ff31d3..4cfc569098 100644 --- a/config/examples/FYSETC/Cheetah 1.2/base/Configuration.h +++ b/config/examples/FYSETC/Cheetah 1.2/base/Configuration.h @@ -2095,7 +2095,7 @@ // Use software PWM to drive the fan, as for the heaters. This uses a very low frequency // which is not as annoying as with the hardware PWM. On the other hand, if this frequency // is too low, you should also increment SOFT_PWM_SCALE. -//#define FAN_SOFT_PWM +#define FAN_SOFT_PWM // Incrementing this by 1 will double the software PWM frequency, // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. diff --git a/config/examples/FYSETC/Cheetah 1.2/base/Configuration_adv.h b/config/examples/FYSETC/Cheetah 1.2/base/Configuration_adv.h index 62390a8ba4..29da3f1d88 100644 --- a/config/examples/FYSETC/Cheetah 1.2/base/Configuration_adv.h +++ b/config/examples/FYSETC/Cheetah 1.2/base/Configuration_adv.h @@ -1903,7 +1903,7 @@ * Define you own with * { , , hysteresis_start[1..8] } */ - #define CHOPPER_TIMING CHOPPER_DEFAULT_12V + #define CHOPPER_TIMING CHOPPER_DEFAULT_24V /** * Monitor Trinamic drivers for error conditions, diff --git a/config/examples/FYSETC/Cheetah/BLTouch/Configuration.h b/config/examples/FYSETC/Cheetah/BLTouch/Configuration.h index 058db6b6c6..641e88c5cd 100644 --- a/config/examples/FYSETC/Cheetah/BLTouch/Configuration.h +++ b/config/examples/FYSETC/Cheetah/BLTouch/Configuration.h @@ -127,18 +127,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_FYSETC_CHEETAH #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu //#define CUSTOM_MACHINE_NAME "3D Printer" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -256,7 +254,16 @@ */ //#define MAGNETIC_SWITCHING_TOOLHEAD -#if EITHER(SWITCHING_TOOLHEAD, MAGNETIC_SWITCHING_TOOLHEAD) +/** + * Electromagnetic Switching Toolhead + * + * Parking for CoreXY / HBot kinematics. + * Toolheads are parked at one edge and held with an electromagnet. + * Supports more than 2 Toolheads. See https://youtu.be/JolbsAKTKf4 + */ +//#define ELECTROMAGNETIC_SWITCHING_TOOLHEAD + +#if ANY(SWITCHING_TOOLHEAD, MAGNETIC_SWITCHING_TOOLHEAD, ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_POS 235 // (mm) Y position of the toolhead dock #define SWITCHING_TOOLHEAD_Y_SECURITY 10 // (mm) Security distance Y axis #define SWITCHING_TOOLHEAD_Y_CLEAR 60 // (mm) Minimum distance from dock for unobstructed X axis @@ -308,22 +315,20 @@ // @section machine /** - * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN - * - * 0 = No Power Switch - * 1 = ATX - * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC) + * Power Supply Control * - * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' } + * Enable and connect the power supply to the PS_ON_PIN. + * Specify whether the power supply is active HIGH or active LOW. */ -#define POWER_SUPPLY 0 +//#define PSU_CONTROL +//#define PSU_NAME "Power Supply" -#if POWER_SUPPLY > 0 - // Enable this option to leave the PSU off at startup. - // Power to steppers and heaters will need to be turned on with M80. - //#define PS_DEFAULT_OFF +#if ENABLED(PSU_CONTROL) + #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2) - //#define AUTO_POWER_CONTROL // Enable automatic control of the PS_ON pin + //#define PS_DEFAULT_OFF // Keep power off until enabled directly with M80 + + //#define AUTO_POWER_CONTROL // Enable automatic control of the PS_ON pin #if ENABLED(AUTO_POWER_CONTROL) #define AUTO_POWER_FANS // Turn on PSU if fans need power #define AUTO_POWER_E_FANS @@ -333,7 +338,6 @@ //#define AUTO_POWER_CHAMBER_TEMP 30 // (°C) Turn on PSU over this temperature #define POWER_TIMEOUT 30 #endif - #endif // @section temperature @@ -359,6 +363,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -396,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -1529,8 +1534,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1922,31 +1930,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1980,15 +1969,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -2001,6 +1981,43 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + // // Overlord OLED display/controller with i2c buzzer and LEDs // @@ -2078,7 +2095,7 @@ // Use software PWM to drive the fan, as for the heaters. This uses a very low frequency // which is not as annoying as with the hardware PWM. On the other hand, if this frequency // is too low, you should also increment SOFT_PWM_SCALE. -//#define FAN_SOFT_PWM +#define FAN_SOFT_PWM // Incrementing this by 1 will double the software PWM frequency, // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. diff --git a/config/examples/FYSETC/Cheetah/BLTouch/Configuration_adv.h b/config/examples/FYSETC/Cheetah/BLTouch/Configuration_adv.h index 3369b1eea1..4fa3812498 100644 --- a/config/examples/FYSETC/Cheetah/BLTouch/Configuration_adv.h +++ b/config/examples/FYSETC/Cheetah/BLTouch/Configuration_adv.h @@ -651,6 +651,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -1903,7 +1904,7 @@ * Define you own with * { , , hysteresis_start[1..8] } */ - #define CHOPPER_TIMING CHOPPER_DEFAULT_12V + #define CHOPPER_TIMING CHOPPER_DEFAULT_24V /** * Monitor Trinamic drivers for error conditions, diff --git a/config/examples/FYSETC/Cheetah/base/Configuration.h b/config/examples/FYSETC/Cheetah/base/Configuration.h index 569784a298..9075451c0a 100644 --- a/config/examples/FYSETC/Cheetah/base/Configuration.h +++ b/config/examples/FYSETC/Cheetah/base/Configuration.h @@ -2095,7 +2095,7 @@ // Use software PWM to drive the fan, as for the heaters. This uses a very low frequency // which is not as annoying as with the hardware PWM. On the other hand, if this frequency // is too low, you should also increment SOFT_PWM_SCALE. -//#define FAN_SOFT_PWM +#define FAN_SOFT_PWM // Incrementing this by 1 will double the software PWM frequency, // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. diff --git a/config/examples/FYSETC/Cheetah/base/Configuration_adv.h b/config/examples/FYSETC/Cheetah/base/Configuration_adv.h index 3369b1eea1..befd66695e 100644 --- a/config/examples/FYSETC/Cheetah/base/Configuration_adv.h +++ b/config/examples/FYSETC/Cheetah/base/Configuration_adv.h @@ -1903,7 +1903,7 @@ * Define you own with * { , , hysteresis_start[1..8] } */ - #define CHOPPER_TIMING CHOPPER_DEFAULT_12V + #define CHOPPER_TIMING CHOPPER_DEFAULT_24V /** * Monitor Trinamic drivers for error conditions,