From 89fb778684cf3e6f6e41844a1d4d9550a430e350 Mon Sep 17 00:00:00 2001
From: Scott Lahteine <sourcetree@thinkyhead.com>
Date: Sun, 6 Sep 2015 16:16:33 -0700
Subject: [PATCH] Fix up probe pin define and test

---
 Marlin/SanityCheck.h   | 7 ++-----
 Marlin/pins_RAMPS_13.h | 1 -
 Marlin/pins_RUMBA.h    | 1 -
 3 files changed, 2 insertions(+), 7 deletions(-)

diff --git a/Marlin/SanityCheck.h b/Marlin/SanityCheck.h
index 7ad8fb3aca..b868f649fa 100644
--- a/Marlin/SanityCheck.h
+++ b/Marlin/SanityCheck.h
@@ -135,7 +135,7 @@
     #if !PIN_EXISTS(Z_MIN)
       #if !PIN_EXISTS(Z_MIN_PROBE) || (DISABLED(Z_MIN_PROBE_ENDSTOP) || ENABLED(DISABLE_Z_MIN_PROBE_ENDSTOP)) // It's possible for someone to set a pin for the Z probe, but not enable it.
         #if ENABLED(Z_MIN_PROBE_REPEATABILITY_TEST)
-          #error You must have a Z min or Z probe endstop to enable Z_MIN_PROBE_REPEATABILITY_TEST.
+          #error You must have a Z_MIN or Z_PROBE endstop to enable Z_MIN_PROBE_REPEATABILITY_TEST.
         #else
           #error AUTO_BED_LEVELING_FEATURE requires a Z_MIN or Z_PROBE endstop. Z_MIN_PIN or Z_MIN_PROBE_PIN must point to a valid hardware pin.
         #endif
@@ -146,11 +146,8 @@
      * Require a Z probe pin if Z_MIN_PROBE_ENDSTOP is enabled.
      */
     #if ENABLED(Z_MIN_PROBE_ENDSTOP)
-      #ifndef Z_MIN_PROBE_PIN
-        #error You must have a Z_MIN_PROBE_PIN defined in your pins_XXXX.h file if you enable Z_MIN_PROBE_ENDSTOP.
-      #endif
       #if !PIN_EXISTS(Z_MIN_PROBE)
-        #error You must set Z_MIN_PROBE_PIN to a valid pin if you enable Z_MIN_PROBE_ENDSTOP.
+        #error You must have a Z_MIN_PROBE_PIN defined in your pins_XXXX.h file if you enable Z_MIN_PROBE_ENDSTOP.
       #endif
 // Forcing Servo definitions can break some hall effect sensor setups. Leaving these here for further comment.
 //      #ifndef NUM_SERVOS
diff --git a/Marlin/pins_RAMPS_13.h b/Marlin/pins_RAMPS_13.h
index 7f651f3658..69e4c685d4 100644
--- a/Marlin/pins_RAMPS_13.h
+++ b/Marlin/pins_RAMPS_13.h
@@ -40,7 +40,6 @@
 #define Z_ENABLE_PIN       62
 #define Z_MIN_PIN          18
 #define Z_MAX_PIN          19
-#define Z_MIN_PROBE_PIN    -1
 
 #define E0_STEP_PIN        26
 #define E0_DIR_PIN         28
diff --git a/Marlin/pins_RUMBA.h b/Marlin/pins_RUMBA.h
index bc314c9c71..440b863cde 100644
--- a/Marlin/pins_RUMBA.h
+++ b/Marlin/pins_RUMBA.h
@@ -27,7 +27,6 @@
 #define Z_ENABLE_PIN       62
 #define Z_MIN_PIN          33
 #define Z_MAX_PIN          32
-#define Z_MIN_PROBE_PIN    -1
 
 #if ENABLED(Z_MIN_PROBE_ENDSTOP)
   // Define a pin to use as the signal pin on Arduino for the Z probe endstop.