diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h index a1bbbfcb43..3c75cec830 100644 --- a/Marlin/Configuration.h +++ b/Marlin/Configuration.h @@ -771,20 +771,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -864,6 +850,20 @@ // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/default/Configuration.h b/Marlin/src/config/default/Configuration.h index a1bbbfcb43..3c75cec830 100644 --- a/Marlin/src/config/default/Configuration.h +++ b/Marlin/src/config/default/Configuration.h @@ -771,20 +771,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -864,6 +850,20 @@ // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration.h b/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration.h index 5a15e59083..d80eeacc4d 100644 --- a/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration.h +++ b/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration.h @@ -791,20 +791,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -884,6 +870,20 @@ // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/AliExpress/CL-260/Configuration.h b/Marlin/src/config/examples/AliExpress/CL-260/Configuration.h index 082fbc108b..cae8a95653 100644 --- a/Marlin/src/config/examples/AliExpress/CL-260/Configuration.h +++ b/Marlin/src/config/examples/AliExpress/CL-260/Configuration.h @@ -771,20 +771,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -864,6 +850,20 @@ // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/Anet/A2/Configuration.h b/Marlin/src/config/examples/Anet/A2/Configuration.h index 63b6f67f22..ac4b314dd9 100644 --- a/Marlin/src/config/examples/Anet/A2/Configuration.h +++ b/Marlin/src/config/examples/Anet/A2/Configuration.h @@ -754,20 +754,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -847,6 +833,20 @@ // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/Anet/A2plus/Configuration.h b/Marlin/src/config/examples/Anet/A2plus/Configuration.h index 6fdb59d8db..f074ffcb73 100644 --- a/Marlin/src/config/examples/Anet/A2plus/Configuration.h +++ b/Marlin/src/config/examples/Anet/A2plus/Configuration.h @@ -754,20 +754,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -847,6 +833,20 @@ // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/Anet/A6/Configuration.h b/Marlin/src/config/examples/Anet/A6/Configuration.h index 3318c83762..7b242191cb 100644 --- a/Marlin/src/config/examples/Anet/A6/Configuration.h +++ b/Marlin/src/config/examples/Anet/A6/Configuration.h @@ -819,20 +819,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -941,6 +927,20 @@ // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/Anet/A8/Configuration.h b/Marlin/src/config/examples/Anet/A8/Configuration.h index 9a1cdc5bc4..96bf06b880 100644 --- a/Marlin/src/config/examples/Anet/A8/Configuration.h +++ b/Marlin/src/config/examples/Anet/A8/Configuration.h @@ -778,20 +778,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -871,6 +857,20 @@ // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/Azteeg/X5GT/Configuration.h b/Marlin/src/config/examples/Azteeg/X5GT/Configuration.h index 66d679a238..9bba047071 100644 --- a/Marlin/src/config/examples/Azteeg/X5GT/Configuration.h +++ b/Marlin/src/config/examples/Azteeg/X5GT/Configuration.h @@ -771,20 +771,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -864,6 +850,20 @@ // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration.h b/Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration.h index 7fabddff43..bfae318923 100644 --- a/Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration.h +++ b/Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration.h @@ -743,20 +743,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -836,6 +822,20 @@ // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/BIBO/TouchX/default/Configuration.h b/Marlin/src/config/examples/BIBO/TouchX/default/Configuration.h index 6646df5813..0555de8366 100644 --- a/Marlin/src/config/examples/BIBO/TouchX/default/Configuration.h +++ b/Marlin/src/config/examples/BIBO/TouchX/default/Configuration.h @@ -743,20 +743,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -836,6 +822,20 @@ // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/BQ/Hephestos/Configuration.h b/Marlin/src/config/examples/BQ/Hephestos/Configuration.h index d7c6be805a..8e080fa225 100644 --- a/Marlin/src/config/examples/BQ/Hephestos/Configuration.h +++ b/Marlin/src/config/examples/BQ/Hephestos/Configuration.h @@ -759,20 +759,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -852,6 +838,20 @@ // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/BQ/Hephestos_2/Configuration.h b/Marlin/src/config/examples/BQ/Hephestos_2/Configuration.h index 9f6704e3c7..2456cdaedc 100644 --- a/Marlin/src/config/examples/BQ/Hephestos_2/Configuration.h +++ b/Marlin/src/config/examples/BQ/Hephestos_2/Configuration.h @@ -772,20 +772,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -865,6 +851,20 @@ // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/BQ/WITBOX/Configuration.h b/Marlin/src/config/examples/BQ/WITBOX/Configuration.h index e07f06399b..8107d07a6d 100644 --- a/Marlin/src/config/examples/BQ/WITBOX/Configuration.h +++ b/Marlin/src/config/examples/BQ/WITBOX/Configuration.h @@ -759,20 +759,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -852,6 +838,20 @@ // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/Cartesio/Configuration.h b/Marlin/src/config/examples/Cartesio/Configuration.h index a0a429fe97..d5b8d71970 100644 --- a/Marlin/src/config/examples/Cartesio/Configuration.h +++ b/Marlin/src/config/examples/Cartesio/Configuration.h @@ -770,20 +770,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -863,6 +849,20 @@ // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 1 diff --git a/Marlin/src/config/examples/Creality/CR-10/Configuration.h b/Marlin/src/config/examples/Creality/CR-10/Configuration.h index 2bc0c6db02..744149b3cd 100755 --- a/Marlin/src/config/examples/Creality/CR-10/Configuration.h +++ b/Marlin/src/config/examples/Creality/CR-10/Configuration.h @@ -781,20 +781,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -874,6 +860,20 @@ // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/Creality/CR-10S/Configuration.h b/Marlin/src/config/examples/Creality/CR-10S/Configuration.h index d24145184a..6c5bf263b3 100644 --- a/Marlin/src/config/examples/Creality/CR-10S/Configuration.h +++ b/Marlin/src/config/examples/Creality/CR-10S/Configuration.h @@ -775,20 +775,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -868,6 +854,20 @@ // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/Creality/CR-10mini/Configuration.h b/Marlin/src/config/examples/Creality/CR-10mini/Configuration.h index 9949d8331e..f4205889bf 100644 --- a/Marlin/src/config/examples/Creality/CR-10mini/Configuration.h +++ b/Marlin/src/config/examples/Creality/CR-10mini/Configuration.h @@ -790,20 +790,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -883,6 +869,20 @@ // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/Creality/CR-8/Configuration.h b/Marlin/src/config/examples/Creality/CR-8/Configuration.h index 8f4486a231..c5f9ad1ff9 100644 --- a/Marlin/src/config/examples/Creality/CR-8/Configuration.h +++ b/Marlin/src/config/examples/Creality/CR-8/Configuration.h @@ -781,20 +781,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -874,6 +860,20 @@ // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/Creality/Ender-2/Configuration.h b/Marlin/src/config/examples/Creality/Ender-2/Configuration.h index 4be9a3d39b..539e7416c5 100644 --- a/Marlin/src/config/examples/Creality/Ender-2/Configuration.h +++ b/Marlin/src/config/examples/Creality/Ender-2/Configuration.h @@ -775,20 +775,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -868,6 +854,20 @@ // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/Creality/Ender-3/Configuration.h b/Marlin/src/config/examples/Creality/Ender-3/Configuration.h index 0a1934c764..343821f5e4 100644 --- a/Marlin/src/config/examples/Creality/Ender-3/Configuration.h +++ b/Marlin/src/config/examples/Creality/Ender-3/Configuration.h @@ -775,20 +775,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -868,6 +854,20 @@ // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/Creality/Ender-4/Configuration.h b/Marlin/src/config/examples/Creality/Ender-4/Configuration.h index 106209a5f0..7d3203a123 100644 --- a/Marlin/src/config/examples/Creality/Ender-4/Configuration.h +++ b/Marlin/src/config/examples/Creality/Ender-4/Configuration.h @@ -781,20 +781,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -874,6 +860,20 @@ // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/Einstart-S/Configuration.h b/Marlin/src/config/examples/Einstart-S/Configuration.h index f08922b0fc..9201f12070 100644 --- a/Marlin/src/config/examples/Einstart-S/Configuration.h +++ b/Marlin/src/config/examples/Einstart-S/Configuration.h @@ -782,20 +782,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -874,6 +860,20 @@ // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 1 diff --git a/Marlin/src/config/examples/Felix/Configuration.h b/Marlin/src/config/examples/Felix/Configuration.h index 0be1799634..f27a79283a 100644 --- a/Marlin/src/config/examples/Felix/Configuration.h +++ b/Marlin/src/config/examples/Felix/Configuration.h @@ -753,20 +753,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -846,6 +832,20 @@ // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/Felix/DUAL/Configuration.h b/Marlin/src/config/examples/Felix/DUAL/Configuration.h index ab86a7a2bf..a103b89020 100644 --- a/Marlin/src/config/examples/Felix/DUAL/Configuration.h +++ b/Marlin/src/config/examples/Felix/DUAL/Configuration.h @@ -753,20 +753,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -846,6 +832,20 @@ // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration.h b/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration.h index 541eec0cd7..7a328d6438 100644 --- a/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration.h +++ b/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration.h @@ -777,20 +777,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -870,6 +856,20 @@ // Enable the M48 repeatability test to test probe accuracy #define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/Formbot/T-Rex_2+/Configuration.h b/Marlin/src/config/examples/Formbot/T-Rex_2+/Configuration.h index 4df745f433..7a9eab6251 100644 --- a/Marlin/src/config/examples/Formbot/T-Rex_2+/Configuration.h +++ b/Marlin/src/config/examples/Formbot/T-Rex_2+/Configuration.h @@ -795,20 +795,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -888,6 +874,20 @@ // Enable the M48 repeatability test to test probe accuracy #define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/Formbot/T_Rex_3/Configuration.h b/Marlin/src/config/examples/Formbot/T_Rex_3/Configuration.h index fd08ffb14c..d76f21a558 100644 --- a/Marlin/src/config/examples/Formbot/T_Rex_3/Configuration.h +++ b/Marlin/src/config/examples/Formbot/T_Rex_3/Configuration.h @@ -806,20 +806,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -899,6 +885,20 @@ // Enable the M48 repeatability test to test probe accuracy #define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/Geeetech/GT2560/Configuration.h b/Marlin/src/config/examples/Geeetech/GT2560/Configuration.h index 89ffbbac59..3fea05f533 100644 --- a/Marlin/src/config/examples/Geeetech/GT2560/Configuration.h +++ b/Marlin/src/config/examples/Geeetech/GT2560/Configuration.h @@ -786,20 +786,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -879,6 +865,20 @@ // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h b/Marlin/src/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h index 616c033e80..d80622187c 100644 --- a/Marlin/src/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h +++ b/Marlin/src/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h @@ -771,20 +771,6 @@ #define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -864,6 +850,20 @@ // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h b/Marlin/src/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h index d18dee940c..0dc5e6ffb4 100644 --- a/Marlin/src/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h +++ b/Marlin/src/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h @@ -787,20 +787,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -#define PROBING_FANS_OFF // Turn fans off when probing -#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -880,6 +866,20 @@ // Enable the M48 repeatability test to test probe accuracy #define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +#define PROBING_FANS_OFF // Turn fans off when probing +#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h b/Marlin/src/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h index 42b38a95e8..8e94144f32 100644 --- a/Marlin/src/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h +++ b/Marlin/src/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h @@ -786,20 +786,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -879,6 +865,20 @@ // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h b/Marlin/src/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h index 1614eadbae..b3a6d7fbfc 100644 --- a/Marlin/src/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h +++ b/Marlin/src/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h @@ -771,20 +771,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -864,6 +850,20 @@ // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h b/Marlin/src/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h index 56da7b4fce..75464b256a 100644 --- a/Marlin/src/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h +++ b/Marlin/src/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h @@ -771,20 +771,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -864,6 +850,20 @@ // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/Infitary/i3-M508/Configuration.h b/Marlin/src/config/examples/Infitary/i3-M508/Configuration.h index ac98f9d1d0..be758200f5 100644 --- a/Marlin/src/config/examples/Infitary/i3-M508/Configuration.h +++ b/Marlin/src/config/examples/Infitary/i3-M508/Configuration.h @@ -775,20 +775,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -868,6 +854,20 @@ // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/JGAurora/A5/Configuration.h b/Marlin/src/config/examples/JGAurora/A5/Configuration.h index db408b30ea..21c563aca7 100644 --- a/Marlin/src/config/examples/JGAurora/A5/Configuration.h +++ b/Marlin/src/config/examples/JGAurora/A5/Configuration.h @@ -783,20 +783,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -876,6 +862,20 @@ // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/MakerParts/Configuration.h b/Marlin/src/config/examples/MakerParts/Configuration.h index 867da642e5..e0274af936 100644 --- a/Marlin/src/config/examples/MakerParts/Configuration.h +++ b/Marlin/src/config/examples/MakerParts/Configuration.h @@ -791,20 +791,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -884,6 +870,20 @@ // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/Malyan/M150/Configuration.h b/Marlin/src/config/examples/Malyan/M150/Configuration.h index 02f5ae0419..7a92219108 100644 --- a/Marlin/src/config/examples/Malyan/M150/Configuration.h +++ b/Marlin/src/config/examples/Malyan/M150/Configuration.h @@ -763,20 +763,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -860,6 +846,20 @@ // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/Malyan/M200/Configuration.h b/Marlin/src/config/examples/Malyan/M200/Configuration.h index 1e407e9abd..1bbe362271 100644 --- a/Marlin/src/config/examples/Malyan/M200/Configuration.h +++ b/Marlin/src/config/examples/Malyan/M200/Configuration.h @@ -770,20 +770,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -863,6 +849,20 @@ // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/Micromake/C1/basic/Configuration.h b/Marlin/src/config/examples/Micromake/C1/basic/Configuration.h index f03c90f1e2..34f8dd0105 100644 --- a/Marlin/src/config/examples/Micromake/C1/basic/Configuration.h +++ b/Marlin/src/config/examples/Micromake/C1/basic/Configuration.h @@ -775,20 +775,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -868,6 +854,20 @@ // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration.h b/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration.h index 4d6dea22c6..fc2e534766 100644 --- a/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration.h +++ b/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration.h @@ -775,20 +775,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -868,6 +854,20 @@ // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/Mks/Sbase/Configuration.h b/Marlin/src/config/examples/Mks/Sbase/Configuration.h index 2a18893d08..64ade7e894 100644 --- a/Marlin/src/config/examples/Mks/Sbase/Configuration.h +++ b/Marlin/src/config/examples/Mks/Sbase/Configuration.h @@ -771,20 +771,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -864,6 +850,20 @@ // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/RepRapPro/Huxley/Configuration.h b/Marlin/src/config/examples/RepRapPro/Huxley/Configuration.h index caa10e5111..6e30024247 100644 --- a/Marlin/src/config/examples/RepRapPro/Huxley/Configuration.h +++ b/Marlin/src/config/examples/RepRapPro/Huxley/Configuration.h @@ -811,20 +811,6 @@ Black rubber belt(MXL), 18 - tooth aluminium pulley : 87.489 step per mm (Huxley //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -904,6 +890,20 @@ Black rubber belt(MXL), 18 - tooth aluminium pulley : 87.489 step per mm (Huxley // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/RepRapWorld/Megatronics/Configuration.h b/Marlin/src/config/examples/RepRapWorld/Megatronics/Configuration.h index 2abb3afdcd..d589ea9b96 100644 --- a/Marlin/src/config/examples/RepRapWorld/Megatronics/Configuration.h +++ b/Marlin/src/config/examples/RepRapWorld/Megatronics/Configuration.h @@ -771,20 +771,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -864,6 +850,20 @@ // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/RigidBot/Configuration.h b/Marlin/src/config/examples/RigidBot/Configuration.h index 8c48245300..b47cd148a3 100644 --- a/Marlin/src/config/examples/RigidBot/Configuration.h +++ b/Marlin/src/config/examples/RigidBot/Configuration.h @@ -769,20 +769,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -862,6 +848,20 @@ // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/SCARA/Configuration.h b/Marlin/src/config/examples/SCARA/Configuration.h index 9776b9a8a2..cec57a34b7 100644 --- a/Marlin/src/config/examples/SCARA/Configuration.h +++ b/Marlin/src/config/examples/SCARA/Configuration.h @@ -784,20 +784,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -877,6 +863,20 @@ // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/STM32F10/Configuration.h b/Marlin/src/config/examples/STM32F10/Configuration.h index ec6e446208..bf5d3d5fd0 100644 --- a/Marlin/src/config/examples/STM32F10/Configuration.h +++ b/Marlin/src/config/examples/STM32F10/Configuration.h @@ -773,20 +773,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -866,6 +852,20 @@ // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/STM32F4/Configuration.h b/Marlin/src/config/examples/STM32F4/Configuration.h index edb65465d4..f8d7f7232f 100644 --- a/Marlin/src/config/examples/STM32F4/Configuration.h +++ b/Marlin/src/config/examples/STM32F4/Configuration.h @@ -771,20 +771,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -864,6 +850,20 @@ // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/Sanguinololu/Configuration.h b/Marlin/src/config/examples/Sanguinololu/Configuration.h index ec6e59230b..c3abf9090d 100644 --- a/Marlin/src/config/examples/Sanguinololu/Configuration.h +++ b/Marlin/src/config/examples/Sanguinololu/Configuration.h @@ -802,20 +802,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -895,6 +881,20 @@ // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/TheBorg/Configuration.h b/Marlin/src/config/examples/TheBorg/Configuration.h index 4c318e5949..6073566a93 100644 --- a/Marlin/src/config/examples/TheBorg/Configuration.h +++ b/Marlin/src/config/examples/TheBorg/Configuration.h @@ -771,20 +771,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -864,6 +850,20 @@ // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 1 diff --git a/Marlin/src/config/examples/TinyBoy2/Configuration.h b/Marlin/src/config/examples/TinyBoy2/Configuration.h index 0e97820d9d..ac75523091 100644 --- a/Marlin/src/config/examples/TinyBoy2/Configuration.h +++ b/Marlin/src/config/examples/TinyBoy2/Configuration.h @@ -822,20 +822,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -915,6 +901,20 @@ // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/Tronxy/X1/Configuration.h b/Marlin/src/config/examples/Tronxy/X1/Configuration.h index c8d30a29d2..aee8ebe297 100644 --- a/Marlin/src/config/examples/Tronxy/X1/Configuration.h +++ b/Marlin/src/config/examples/Tronxy/X1/Configuration.h @@ -771,20 +771,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -864,6 +850,20 @@ // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/Tronxy/X3A/Configuration.h b/Marlin/src/config/examples/Tronxy/X3A/Configuration.h index e902d288d0..33f71f6d3e 100644 --- a/Marlin/src/config/examples/Tronxy/X3A/Configuration.h +++ b/Marlin/src/config/examples/Tronxy/X3A/Configuration.h @@ -771,20 +771,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -864,6 +850,20 @@ // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/Tronxy/X5S/Configuration.h b/Marlin/src/config/examples/Tronxy/X5S/Configuration.h index cbd5ebc588..5b81ac7d1d 100644 --- a/Marlin/src/config/examples/Tronxy/X5S/Configuration.h +++ b/Marlin/src/config/examples/Tronxy/X5S/Configuration.h @@ -771,20 +771,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -864,6 +850,20 @@ // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/Tronxy/XY100/Configuration.h b/Marlin/src/config/examples/Tronxy/XY100/Configuration.h index 705bdd90d9..9d153ffad4 100644 --- a/Marlin/src/config/examples/Tronxy/XY100/Configuration.h +++ b/Marlin/src/config/examples/Tronxy/XY100/Configuration.h @@ -782,20 +782,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -875,6 +861,20 @@ // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/UltiMachine/Archim2/Configuration.h b/Marlin/src/config/examples/UltiMachine/Archim2/Configuration.h index e5a5e69aaa..03241a40cb 100644 --- a/Marlin/src/config/examples/UltiMachine/Archim2/Configuration.h +++ b/Marlin/src/config/examples/UltiMachine/Archim2/Configuration.h @@ -771,20 +771,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -864,6 +850,20 @@ // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/Velleman/K8200/Configuration.h b/Marlin/src/config/examples/Velleman/K8200/Configuration.h index ca3ce5fb38..aa4ccadae2 100644 --- a/Marlin/src/config/examples/Velleman/K8200/Configuration.h +++ b/Marlin/src/config/examples/Velleman/K8200/Configuration.h @@ -800,20 +800,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -893,6 +879,20 @@ // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/Velleman/K8400/Configuration.h b/Marlin/src/config/examples/Velleman/K8400/Configuration.h index cb44eadb1a..d10e4b6ca2 100644 --- a/Marlin/src/config/examples/Velleman/K8400/Configuration.h +++ b/Marlin/src/config/examples/Velleman/K8400/Configuration.h @@ -771,20 +771,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -864,6 +850,20 @@ // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/Velleman/K8400/Dual-head/Configuration.h b/Marlin/src/config/examples/Velleman/K8400/Dual-head/Configuration.h index 8c0a7ddb0e..3755f9be6b 100644 --- a/Marlin/src/config/examples/Velleman/K8400/Dual-head/Configuration.h +++ b/Marlin/src/config/examples/Velleman/K8400/Dual-head/Configuration.h @@ -771,20 +771,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -864,6 +850,20 @@ // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/Wanhao/Duplicator 6/Configuration.h b/Marlin/src/config/examples/Wanhao/Duplicator 6/Configuration.h index 40d16901a6..634c122f9b 100644 --- a/Marlin/src/config/examples/Wanhao/Duplicator 6/Configuration.h +++ b/Marlin/src/config/examples/Wanhao/Duplicator 6/Configuration.h @@ -781,20 +781,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -874,6 +860,20 @@ // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/adafruit/ST7565/Configuration.h b/Marlin/src/config/examples/adafruit/ST7565/Configuration.h index 4323a3e420..9acd73970c 100644 --- a/Marlin/src/config/examples/adafruit/ST7565/Configuration.h +++ b/Marlin/src/config/examples/adafruit/ST7565/Configuration.h @@ -771,20 +771,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -864,6 +850,20 @@ // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/delta/Anycubic/Kossel/Configuration.h b/Marlin/src/config/examples/delta/Anycubic/Kossel/Configuration.h index 1ac25e7232..befadcb0d7 100644 --- a/Marlin/src/config/examples/delta/Anycubic/Kossel/Configuration.h +++ b/Marlin/src/config/examples/delta/Anycubic/Kossel/Configuration.h @@ -894,20 +894,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -915,9 +901,52 @@ //#define Z_PROBE_SLED //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. -// -// For Z_PROBE_ALLEN_KEY see the Delta example configurations. -// +/** + * Allen key retractable z-probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe + * Deploys by touching z-axis belt. Retracts by pushing the probe down. Uses Z_MIN_PIN. + */ +//#define Z_PROBE_ALLEN_KEY + +#if ENABLED(Z_PROBE_ALLEN_KEY) + // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29, + // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe. + + #define Z_PROBE_ALLEN_KEY_DEPLOY_1_X 30.0 + #define Z_PROBE_ALLEN_KEY_DEPLOY_1_Y DELTA_PRINTABLE_RADIUS + #define Z_PROBE_ALLEN_KEY_DEPLOY_1_Z 100.0 + #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_SPEED + + #define Z_PROBE_ALLEN_KEY_DEPLOY_2_X 0.0 + #define Z_PROBE_ALLEN_KEY_DEPLOY_2_Y DELTA_PRINTABLE_RADIUS + #define Z_PROBE_ALLEN_KEY_DEPLOY_2_Z 100.0 + #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_SPEED)/10 + + #define Z_PROBE_ALLEN_KEY_DEPLOY_3_X Z_PROBE_ALLEN_KEY_DEPLOY_2_X * 0.75 + #define Z_PROBE_ALLEN_KEY_DEPLOY_3_Y Z_PROBE_ALLEN_KEY_DEPLOY_2_Y * 0.75 + #define Z_PROBE_ALLEN_KEY_DEPLOY_3_Z Z_PROBE_ALLEN_KEY_DEPLOY_2_Z + #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_SPEED + + #define Z_PROBE_ALLEN_KEY_STOW_1_X -64.0 // Move the probe into position + #define Z_PROBE_ALLEN_KEY_STOW_1_Y 56.0 + #define Z_PROBE_ALLEN_KEY_STOW_1_Z 23.0 + #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_SPEED + + #define Z_PROBE_ALLEN_KEY_STOW_2_X -64.0 // Push it down + #define Z_PROBE_ALLEN_KEY_STOW_2_Y 56.0 + #define Z_PROBE_ALLEN_KEY_STOW_2_Z 3.0 + #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_SPEED)/10 + + #define Z_PROBE_ALLEN_KEY_STOW_3_X -64.0 // Move it up to clear + #define Z_PROBE_ALLEN_KEY_STOW_3_Y 56.0 + #define Z_PROBE_ALLEN_KEY_STOW_3_Z 50.0 + #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_SPEED + + #define Z_PROBE_ALLEN_KEY_STOW_4_X 0.0 + #define Z_PROBE_ALLEN_KEY_STOW_4_Y 0.0 + #define Z_PROBE_ALLEN_KEY_STOW_4_Z Z_PROBE_ALLEN_KEY_STOW_3_Z + #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_SPEED + +#endif // Z_PROBE_ALLEN_KEY /** * Z Probe to nozzle (X,Y) offset, relative to (0, 0). @@ -966,53 +995,6 @@ // Set to 3 or more for slow probes, averaging the results. #define MULTIPLE_PROBING 3 -/** - * Allen key retractable z-probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe - * Deploys by touching z-axis belt. Retracts by pushing the probe down. Uses Z_MIN_PIN. - */ -//#define Z_PROBE_ALLEN_KEY - -#if ENABLED(Z_PROBE_ALLEN_KEY) - // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29, - // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe. - - #define Z_PROBE_ALLEN_KEY_DEPLOY_1_X 30.0 - #define Z_PROBE_ALLEN_KEY_DEPLOY_1_Y DELTA_PRINTABLE_RADIUS - #define Z_PROBE_ALLEN_KEY_DEPLOY_1_Z 100.0 - #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_SPEED - - #define Z_PROBE_ALLEN_KEY_DEPLOY_2_X 0.0 - #define Z_PROBE_ALLEN_KEY_DEPLOY_2_Y DELTA_PRINTABLE_RADIUS - #define Z_PROBE_ALLEN_KEY_DEPLOY_2_Z 100.0 - #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_SPEED)/10 - - #define Z_PROBE_ALLEN_KEY_DEPLOY_3_X Z_PROBE_ALLEN_KEY_DEPLOY_2_X * 0.75 - #define Z_PROBE_ALLEN_KEY_DEPLOY_3_Y Z_PROBE_ALLEN_KEY_DEPLOY_2_Y * 0.75 - #define Z_PROBE_ALLEN_KEY_DEPLOY_3_Z Z_PROBE_ALLEN_KEY_DEPLOY_2_Z - #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_SPEED - - #define Z_PROBE_ALLEN_KEY_STOW_1_X -64.0 // Move the probe into position - #define Z_PROBE_ALLEN_KEY_STOW_1_Y 56.0 - #define Z_PROBE_ALLEN_KEY_STOW_1_Z 23.0 - #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_SPEED - - #define Z_PROBE_ALLEN_KEY_STOW_2_X -64.0 // Push it down - #define Z_PROBE_ALLEN_KEY_STOW_2_Y 56.0 - #define Z_PROBE_ALLEN_KEY_STOW_2_Z 3.0 - #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_SPEED)/10 - - #define Z_PROBE_ALLEN_KEY_STOW_3_X -64.0 // Move it up to clear - #define Z_PROBE_ALLEN_KEY_STOW_3_Y 56.0 - #define Z_PROBE_ALLEN_KEY_STOW_3_Z 50.0 - #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_SPEED - - #define Z_PROBE_ALLEN_KEY_STOW_4_X 0.0 - #define Z_PROBE_ALLEN_KEY_STOW_4_Y 0.0 - #define Z_PROBE_ALLEN_KEY_STOW_4_Z Z_PROBE_ALLEN_KEY_STOW_3_Z - #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_SPEED - -#endif // Z_PROBE_ALLEN_KEY - /** * Z probes require clearance when deploying, stowing, and moving between * probe points to avoid hitting the bed and other hardware. @@ -1043,6 +1025,20 @@ #define Z_MIN_PROBE_REPEATABILITY_TEST #endif +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration.h b/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration.h index 1f8d149a43..38726e6998 100644 --- a/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration.h +++ b/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration.h @@ -853,20 +853,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -874,50 +860,6 @@ //#define Z_PROBE_SLED //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. -// -// For Z_PROBE_ALLEN_KEY see the Delta example configurations. -// - -/** - * Z Probe to nozzle (X,Y) offset, relative to (0, 0). - * X and Y offsets must be integers. - * - * In the following example the X and Y offsets are both positive: - * #define X_PROBE_OFFSET_FROM_EXTRUDER 10 - * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 - * - * +-- BACK ---+ - * | | - * L | (+) P | R <-- probe (20,20) - * E | | I - * F | (-) N (+) | G <-- nozzle (10,10) - * T | | H - * | (-) | T - * | | - * O-- FRONT --+ - * (0,0) - */ -#define X_PROBE_OFFSET_FROM_EXTRUDER 0 // X offset: -left +right [of the nozzle] -#define Y_PROBE_OFFSET_FROM_EXTRUDER 0 // Y offset: -front +behind [the nozzle] -#define Z_PROBE_OFFSET_FROM_EXTRUDER 0.10 // Z offset: -below +above [the nozzle] - -// Certain types of probes need to stay away from edges -#define MIN_PROBE_EDGE 20 - -// X and Y axis travel speed (mm/m) between probes -#define XY_PROBE_SPEED 5000 - -// Feedrate (mm/m) for the first approach when double-probing (MULTIPLE_PROBING == 2) -#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z - -// Feedrate (mm/m) for the "accurate" probe of each point -#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST) / 6 - -// The number of probes to perform at each point. -// Set to 2 for a fast/slow probe, using the second probe result. -// Set to 3 or more for slow probes, averaging the results. -//#define MULTIPLE_PROBING 2 - /** * Allen key retractable z-probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe * Deploys by touching z-axis belt. Retracts by pushing the probe down. Uses Z_MIN_PIN. @@ -968,6 +910,46 @@ #endif // Z_PROBE_ALLEN_KEY +/** + * Z Probe to nozzle (X,Y) offset, relative to (0, 0). + * X and Y offsets must be integers. + * + * In the following example the X and Y offsets are both positive: + * #define X_PROBE_OFFSET_FROM_EXTRUDER 10 + * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 + * + * +-- BACK ---+ + * | | + * L | (+) P | R <-- probe (20,20) + * E | | I + * F | (-) N (+) | G <-- nozzle (10,10) + * T | | H + * | (-) | T + * | | + * O-- FRONT --+ + * (0,0) + */ +#define X_PROBE_OFFSET_FROM_EXTRUDER 0 // X offset: -left +right [of the nozzle] +#define Y_PROBE_OFFSET_FROM_EXTRUDER 0 // Y offset: -front +behind [the nozzle] +#define Z_PROBE_OFFSET_FROM_EXTRUDER 0.10 // Z offset: -below +above [the nozzle] + +// Certain types of probes need to stay away from edges +#define MIN_PROBE_EDGE 20 + +// X and Y axis travel speed (mm/m) between probes +#define XY_PROBE_SPEED 5000 + +// Feedrate (mm/m) for the first approach when double-probing (MULTIPLE_PROBING == 2) +#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z + +// Feedrate (mm/m) for the "accurate" probe of each point +#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST) / 6 + +// The number of probes to perform at each point. +// Set to 2 for a fast/slow probe, using the second probe result. +// Set to 3 or more for slow probes, averaging the results. +//#define MULTIPLE_PROBING 2 + /** * Z probes require clearance when deploying, stowing, and moving between * probe points to avoid hitting the bed and other hardware. @@ -996,6 +978,20 @@ // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/delta/FLSUN/kossel/Configuration.h b/Marlin/src/config/examples/delta/FLSUN/kossel/Configuration.h index 41a7299874..6521fe6e2b 100644 --- a/Marlin/src/config/examples/delta/FLSUN/kossel/Configuration.h +++ b/Marlin/src/config/examples/delta/FLSUN/kossel/Configuration.h @@ -853,20 +853,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -874,50 +860,6 @@ //#define Z_PROBE_SLED //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. -// -// For Z_PROBE_ALLEN_KEY see the Delta example configurations. -// - -/** - * Z Probe to nozzle (X,Y) offset, relative to (0, 0). - * X and Y offsets must be integers. - * - * In the following example the X and Y offsets are both positive: - * #define X_PROBE_OFFSET_FROM_EXTRUDER 10 - * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 - * - * +-- BACK ---+ - * | | - * L | (+) P | R <-- probe (20,20) - * E | | I - * F | (-) N (+) | G <-- nozzle (10,10) - * T | | H - * | (-) | T - * | | - * O-- FRONT --+ - * (0,0) - */ -#define X_PROBE_OFFSET_FROM_EXTRUDER 0 // X offset: -left +right [of the nozzle] -#define Y_PROBE_OFFSET_FROM_EXTRUDER 0 // Y offset: -front +behind [the nozzle] -#define Z_PROBE_OFFSET_FROM_EXTRUDER 0.10 // Z offset: -below +above [the nozzle] - -// Certain types of probes need to stay away from edges -#define MIN_PROBE_EDGE 20 - -// X and Y axis travel speed (mm/m) between probes -#define XY_PROBE_SPEED 5000 - -// Feedrate (mm/m) for the first approach when double-probing (MULTIPLE_PROBING == 2) -#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z - -// Feedrate (mm/m) for the "accurate" probe of each point -#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST) / 6 - -// The number of probes to perform at each point. -// Set to 2 for a fast/slow probe, using the second probe result. -// Set to 3 or more for slow probes, averaging the results. -//#define MULTIPLE_PROBING 2 - /** * Allen key retractable z-probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe * Deploys by touching z-axis belt. Retracts by pushing the probe down. Uses Z_MIN_PIN. @@ -967,6 +909,46 @@ #endif // Z_PROBE_ALLEN_KEY +/** + * Z Probe to nozzle (X,Y) offset, relative to (0, 0). + * X and Y offsets must be integers. + * + * In the following example the X and Y offsets are both positive: + * #define X_PROBE_OFFSET_FROM_EXTRUDER 10 + * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 + * + * +-- BACK ---+ + * | | + * L | (+) P | R <-- probe (20,20) + * E | | I + * F | (-) N (+) | G <-- nozzle (10,10) + * T | | H + * | (-) | T + * | | + * O-- FRONT --+ + * (0,0) + */ +#define X_PROBE_OFFSET_FROM_EXTRUDER 0 // X offset: -left +right [of the nozzle] +#define Y_PROBE_OFFSET_FROM_EXTRUDER 0 // Y offset: -front +behind [the nozzle] +#define Z_PROBE_OFFSET_FROM_EXTRUDER 0.10 // Z offset: -below +above [the nozzle] + +// Certain types of probes need to stay away from edges +#define MIN_PROBE_EDGE 20 + +// X and Y axis travel speed (mm/m) between probes +#define XY_PROBE_SPEED 5000 + +// Feedrate (mm/m) for the first approach when double-probing (MULTIPLE_PROBING == 2) +#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z + +// Feedrate (mm/m) for the "accurate" probe of each point +#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST) / 6 + +// The number of probes to perform at each point. +// Set to 2 for a fast/slow probe, using the second probe result. +// Set to 3 or more for slow probes, averaging the results. +//#define MULTIPLE_PROBING 2 + /** * Z probes require clearance when deploying, stowing, and moving between * probe points to avoid hitting the bed and other hardware. @@ -995,6 +977,20 @@ // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration.h b/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration.h index 5e7b54d0a2..643a078a08 100644 --- a/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration.h +++ b/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration.h @@ -853,20 +853,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -874,50 +860,6 @@ //#define Z_PROBE_SLED //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. -// -// For Z_PROBE_ALLEN_KEY see the Delta example configurations. -// - -/** - * Z Probe to nozzle (X,Y) offset, relative to (0, 0). - * X and Y offsets must be integers. - * - * In the following example the X and Y offsets are both positive: - * #define X_PROBE_OFFSET_FROM_EXTRUDER 10 - * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 - * - * +-- BACK ---+ - * | | - * L | (+) P | R <-- probe (20,20) - * E | | I - * F | (-) N (+) | G <-- nozzle (10,10) - * T | | H - * | (-) | T - * | | - * O-- FRONT --+ - * (0,0) - */ -#define X_PROBE_OFFSET_FROM_EXTRUDER 0 // X offset: -left +right [of the nozzle] -#define Y_PROBE_OFFSET_FROM_EXTRUDER 0 // Y offset: -front +behind [the nozzle] -#define Z_PROBE_OFFSET_FROM_EXTRUDER 0.25 // Z offset: -below +above [the nozzle] - -// Certain types of probes need to stay away from edges -#define MIN_PROBE_EDGE 10 - -// X and Y axis travel speed (mm/m) between probes -#define XY_PROBE_SPEED 2000 - -// Feedrate (mm/m) for the first approach when double-probing (MULTIPLE_PROBING == 2) -#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z - -// Feedrate (mm/m) for the "accurate" probe of each point -#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2) - -// The number of probes to perform at each point. -// Set to 2 for a fast/slow probe, using the second probe result. -// Set to 3 or more for slow probes, averaging the results. -#define MULTIPLE_PROBING 2 - /** * Allen key retractable z-probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe * Deploys by touching z-axis belt. Retracts by pushing the probe down. Uses Z_MIN_PIN. @@ -967,6 +909,46 @@ #endif // Z_PROBE_ALLEN_KEY +/** + * Z Probe to nozzle (X,Y) offset, relative to (0, 0). + * X and Y offsets must be integers. + * + * In the following example the X and Y offsets are both positive: + * #define X_PROBE_OFFSET_FROM_EXTRUDER 10 + * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 + * + * +-- BACK ---+ + * | | + * L | (+) P | R <-- probe (20,20) + * E | | I + * F | (-) N (+) | G <-- nozzle (10,10) + * T | | H + * | (-) | T + * | | + * O-- FRONT --+ + * (0,0) + */ +#define X_PROBE_OFFSET_FROM_EXTRUDER 0 // X offset: -left +right [of the nozzle] +#define Y_PROBE_OFFSET_FROM_EXTRUDER 0 // Y offset: -front +behind [the nozzle] +#define Z_PROBE_OFFSET_FROM_EXTRUDER 0.25 // Z offset: -below +above [the nozzle] + +// Certain types of probes need to stay away from edges +#define MIN_PROBE_EDGE 10 + +// X and Y axis travel speed (mm/m) between probes +#define XY_PROBE_SPEED 2000 + +// Feedrate (mm/m) for the first approach when double-probing (MULTIPLE_PROBING == 2) +#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z + +// Feedrate (mm/m) for the "accurate" probe of each point +#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2) + +// The number of probes to perform at each point. +// Set to 2 for a fast/slow probe, using the second probe result. +// Set to 3 or more for slow probes, averaging the results. +#define MULTIPLE_PROBING 2 + /** * Z probes require clearance when deploying, stowing, and moving between * probe points to avoid hitting the bed and other hardware. @@ -995,6 +977,20 @@ // Enable the M48 repeatability test to test probe accuracy #define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/delta/Hatchbox_Alpha/Configuration.h b/Marlin/src/config/examples/delta/Hatchbox_Alpha/Configuration.h index 3bba948f49..d5d9fe4dc5 100644 --- a/Marlin/src/config/examples/delta/Hatchbox_Alpha/Configuration.h +++ b/Marlin/src/config/examples/delta/Hatchbox_Alpha/Configuration.h @@ -858,20 +858,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -879,50 +865,6 @@ //#define Z_PROBE_SLED //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. -// -// For Z_PROBE_ALLEN_KEY see the Delta example configurations. -// - -/** - * Z Probe to nozzle (X,Y) offset, relative to (0, 0). - * X and Y offsets must be integers. - * - * In the following example the X and Y offsets are both positive: - * #define X_PROBE_OFFSET_FROM_EXTRUDER 10 - * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 - * - * +-- BACK ---+ - * | | - * L | (+) P | R <-- probe (20,20) - * E | | I - * F | (-) N (+) | G <-- nozzle (10,10) - * T | | H - * | (-) | T - * | | - * O-- FRONT --+ - * (0,0) - */ -#define X_PROBE_OFFSET_FROM_EXTRUDER 0 // X offset: -left +right [of the nozzle] -#define Y_PROBE_OFFSET_FROM_EXTRUDER 0 // Y offset: -front +behind [the nozzle] -#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle] - -// Certain types of probes need to stay away from edges -#define MIN_PROBE_EDGE 10 - -// X and Y axis travel speed (mm/m) between probes -#define XY_PROBE_SPEED 4000 - -// Feedrate (mm/m) for the first approach when double-probing (MULTIPLE_PROBING == 2) -#define Z_PROBE_SPEED_FAST (HOMING_FEEDRATE_Z / 4) - -// Feedrate (mm/m) for the "accurate" probe of each point -#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 4) - -// The number of probes to perform at each point. -// Set to 2 for a fast/slow probe, using the second probe result. -// Set to 3 or more for slow probes, averaging the results. -#define MULTIPLE_PROBING 2 - /** * Allen key retractable z-probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe * Deploys by touching z-axis belt. Retracts by pushing the probe down. Uses Z_MIN_PIN. @@ -970,6 +912,46 @@ #endif // Z_PROBE_ALLEN_KEY +/** + * Z Probe to nozzle (X,Y) offset, relative to (0, 0). + * X and Y offsets must be integers. + * + * In the following example the X and Y offsets are both positive: + * #define X_PROBE_OFFSET_FROM_EXTRUDER 10 + * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 + * + * +-- BACK ---+ + * | | + * L | (+) P | R <-- probe (20,20) + * E | | I + * F | (-) N (+) | G <-- nozzle (10,10) + * T | | H + * | (-) | T + * | | + * O-- FRONT --+ + * (0,0) + */ +#define X_PROBE_OFFSET_FROM_EXTRUDER 0 // X offset: -left +right [of the nozzle] +#define Y_PROBE_OFFSET_FROM_EXTRUDER 0 // Y offset: -front +behind [the nozzle] +#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle] + +// Certain types of probes need to stay away from edges +#define MIN_PROBE_EDGE 10 + +// X and Y axis travel speed (mm/m) between probes +#define XY_PROBE_SPEED 4000 + +// Feedrate (mm/m) for the first approach when double-probing (MULTIPLE_PROBING == 2) +#define Z_PROBE_SPEED_FAST (HOMING_FEEDRATE_Z / 4) + +// Feedrate (mm/m) for the "accurate" probe of each point +#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 4) + +// The number of probes to perform at each point. +// Set to 2 for a fast/slow probe, using the second probe result. +// Set to 3 or more for slow probes, averaging the results. +#define MULTIPLE_PROBING 2 + /** * Z probes require clearance when deploying, stowing, and moving between * probe points to avoid hitting the bed and other hardware. @@ -998,6 +980,20 @@ // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/delta/generic/Configuration.h b/Marlin/src/config/examples/delta/generic/Configuration.h index 38beaf6488..c41f4dc1ba 100644 --- a/Marlin/src/config/examples/delta/generic/Configuration.h +++ b/Marlin/src/config/examples/delta/generic/Configuration.h @@ -843,20 +843,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -864,50 +850,6 @@ //#define Z_PROBE_SLED //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. -// -// For Z_PROBE_ALLEN_KEY see the Delta example configurations. -// - -/** - * Z Probe to nozzle (X,Y) offset, relative to (0, 0). - * X and Y offsets must be integers. - * - * In the following example the X and Y offsets are both positive: - * #define X_PROBE_OFFSET_FROM_EXTRUDER 10 - * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 - * - * +-- BACK ---+ - * | | - * L | (+) P | R <-- probe (20,20) - * E | | I - * F | (-) N (+) | G <-- nozzle (10,10) - * T | | H - * | (-) | T - * | | - * O-- FRONT --+ - * (0,0) - */ -#define X_PROBE_OFFSET_FROM_EXTRUDER 0 // X offset: -left +right [of the nozzle] -#define Y_PROBE_OFFSET_FROM_EXTRUDER -10 // Y offset: -front +behind [the nozzle] -#define Z_PROBE_OFFSET_FROM_EXTRUDER -3.5 // Z offset: -below +above [the nozzle] - -// Certain types of probes need to stay away from edges -#define MIN_PROBE_EDGE 10 - -// X and Y axis travel speed (mm/m) between probes -#define XY_PROBE_SPEED 4000 - -// Feedrate (mm/m) for the first approach when double-probing (MULTIPLE_PROBING == 2) -#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z - -// Feedrate (mm/m) for the "accurate" probe of each point -#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2) - -// The number of probes to perform at each point. -// Set to 2 for a fast/slow probe, using the second probe result. -// Set to 3 or more for slow probes, averaging the results. -//#define MULTIPLE_PROBING 2 - /** * Allen key retractable z-probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe * Deploys by touching z-axis belt. Retracts by pushing the probe down. Uses Z_MIN_PIN. @@ -955,6 +897,46 @@ #endif // Z_PROBE_ALLEN_KEY +/** + * Z Probe to nozzle (X,Y) offset, relative to (0, 0). + * X and Y offsets must be integers. + * + * In the following example the X and Y offsets are both positive: + * #define X_PROBE_OFFSET_FROM_EXTRUDER 10 + * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 + * + * +-- BACK ---+ + * | | + * L | (+) P | R <-- probe (20,20) + * E | | I + * F | (-) N (+) | G <-- nozzle (10,10) + * T | | H + * | (-) | T + * | | + * O-- FRONT --+ + * (0,0) + */ +#define X_PROBE_OFFSET_FROM_EXTRUDER 0 // X offset: -left +right [of the nozzle] +#define Y_PROBE_OFFSET_FROM_EXTRUDER -10 // Y offset: -front +behind [the nozzle] +#define Z_PROBE_OFFSET_FROM_EXTRUDER -3.5 // Z offset: -below +above [the nozzle] + +// Certain types of probes need to stay away from edges +#define MIN_PROBE_EDGE 10 + +// X and Y axis travel speed (mm/m) between probes +#define XY_PROBE_SPEED 4000 + +// Feedrate (mm/m) for the first approach when double-probing (MULTIPLE_PROBING == 2) +#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z + +// Feedrate (mm/m) for the "accurate" probe of each point +#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2) + +// The number of probes to perform at each point. +// Set to 2 for a fast/slow probe, using the second probe result. +// Set to 3 or more for slow probes, averaging the results. +//#define MULTIPLE_PROBING 2 + /** * Z probes require clearance when deploying, stowing, and moving between * probe points to avoid hitting the bed and other hardware. @@ -983,6 +965,20 @@ // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/delta/kossel_mini/Configuration.h b/Marlin/src/config/examples/delta/kossel_mini/Configuration.h index d55eabcc7a..919f0eb5cf 100644 --- a/Marlin/src/config/examples/delta/kossel_mini/Configuration.h +++ b/Marlin/src/config/examples/delta/kossel_mini/Configuration.h @@ -843,20 +843,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -864,50 +850,6 @@ //#define Z_PROBE_SLED //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. -// -// For Z_PROBE_ALLEN_KEY see the Delta example configurations. -// - -/** - * Z Probe to nozzle (X,Y) offset, relative to (0, 0). - * X and Y offsets must be integers. - * - * In the following example the X and Y offsets are both positive: - * #define X_PROBE_OFFSET_FROM_EXTRUDER 10 - * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 - * - * +-- BACK ---+ - * | | - * L | (+) P | R <-- probe (20,20) - * E | | I - * F | (-) N (+) | G <-- nozzle (10,10) - * T | | H - * | (-) | T - * | | - * O-- FRONT --+ - * (0,0) - */ -#define X_PROBE_OFFSET_FROM_EXTRUDER 0 // X offset: -left +right [of the nozzle] -#define Y_PROBE_OFFSET_FROM_EXTRUDER -10 // Y offset: -front +behind [the nozzle] -#define Z_PROBE_OFFSET_FROM_EXTRUDER -3.5 // Z offset: -below +above [the nozzle] - -// Certain types of probes need to stay away from edges -#define MIN_PROBE_EDGE 10 - -// X and Y axis travel speed (mm/m) between probes -#define XY_PROBE_SPEED 4000 - -// Feedrate (mm/m) for the first approach when double-probing (MULTIPLE_PROBING == 2) -#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z - -// Feedrate (mm/m) for the "accurate" probe of each point -#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2) - -// The number of probes to perform at each point. -// Set to 2 for a fast/slow probe, using the second probe result. -// Set to 3 or more for slow probes, averaging the results. -//#define MULTIPLE_PROBING 2 - /** * Allen key retractable z-probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe * Deploys by touching z-axis belt. Retracts by pushing the probe down. Uses Z_MIN_PIN. @@ -957,6 +899,46 @@ #endif // Z_PROBE_ALLEN_KEY +/** + * Z Probe to nozzle (X,Y) offset, relative to (0, 0). + * X and Y offsets must be integers. + * + * In the following example the X and Y offsets are both positive: + * #define X_PROBE_OFFSET_FROM_EXTRUDER 10 + * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 + * + * +-- BACK ---+ + * | | + * L | (+) P | R <-- probe (20,20) + * E | | I + * F | (-) N (+) | G <-- nozzle (10,10) + * T | | H + * | (-) | T + * | | + * O-- FRONT --+ + * (0,0) + */ +#define X_PROBE_OFFSET_FROM_EXTRUDER 0 // X offset: -left +right [of the nozzle] +#define Y_PROBE_OFFSET_FROM_EXTRUDER -10 // Y offset: -front +behind [the nozzle] +#define Z_PROBE_OFFSET_FROM_EXTRUDER -3.5 // Z offset: -below +above [the nozzle] + +// Certain types of probes need to stay away from edges +#define MIN_PROBE_EDGE 10 + +// X and Y axis travel speed (mm/m) between probes +#define XY_PROBE_SPEED 4000 + +// Feedrate (mm/m) for the first approach when double-probing (MULTIPLE_PROBING == 2) +#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z + +// Feedrate (mm/m) for the "accurate" probe of each point +#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2) + +// The number of probes to perform at each point. +// Set to 2 for a fast/slow probe, using the second probe result. +// Set to 3 or more for slow probes, averaging the results. +//#define MULTIPLE_PROBING 2 + /** * Z probes require clearance when deploying, stowing, and moving between * probe points to avoid hitting the bed and other hardware. @@ -985,6 +967,20 @@ // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/delta/kossel_pro/Configuration.h b/Marlin/src/config/examples/delta/kossel_pro/Configuration.h index 926dcb1ddf..d6123a75de 100644 --- a/Marlin/src/config/examples/delta/kossel_pro/Configuration.h +++ b/Marlin/src/config/examples/delta/kossel_pro/Configuration.h @@ -836,20 +836,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -857,53 +843,6 @@ //#define Z_PROBE_SLED //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. -// -// For Z_PROBE_ALLEN_KEY see the Delta example configurations. -// - -/** - * Z Probe to nozzle (X,Y) offset, relative to (0, 0). - * X and Y offsets must be integers. - * - * In the following example the X and Y offsets are both positive: - * #define X_PROBE_OFFSET_FROM_EXTRUDER 10 - * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 - * - * +-- BACK ---+ - * | | - * L | (+) P | R <-- probe (20,20) - * E | | I - * F | (-) N (+) | G <-- nozzle (10,10) - * T | | H - * | (-) | T - * | | - * O-- FRONT --+ - * (0,0) - */ -#define X_PROBE_OFFSET_FROM_EXTRUDER -23 // KosselPro actual: -22.919 -#define Y_PROBE_OFFSET_FROM_EXTRUDER -6 // KosselPro actual: -6.304 -/** - * Kossel Pro note: The correct value is likely -17.45 but I'd rather err on the side of - * not giving someone a head crash. Use something like G29 Z-0.2 to adjust as needed. - */ -#define Z_PROBE_OFFSET_FROM_EXTRUDER -17.25 // Increase this if the first layer is too thin (remember: it's a negative number so increase means closer to zero). -// Certain types of probes need to stay away from edges -#define MIN_PROBE_EDGE 10 - -// X and Y axis travel speed (mm/m) between probes -#define XY_PROBE_SPEED 8000 - -// Feedrate (mm/m) for the first approach when double-probing (MULTIPLE_PROBING == 2) -#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z - -// Feedrate (mm/m) for the "accurate" probe of each point -#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2) - -// The number of probes to perform at each point. -// Set to 2 for a fast/slow probe, using the second probe result. -// Set to 3 or more for slow probes, averaging the results. -//#define MULTIPLE_PROBING 2 - /** * Allen key retractable z-probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe * Deploys by touching z-axis belt. Retracts by pushing the probe down. Uses Z_MIN_PIN. @@ -957,6 +896,49 @@ #endif // Z_PROBE_ALLEN_KEY +/** + * Z Probe to nozzle (X,Y) offset, relative to (0, 0). + * X and Y offsets must be integers. + * + * In the following example the X and Y offsets are both positive: + * #define X_PROBE_OFFSET_FROM_EXTRUDER 10 + * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 + * + * +-- BACK ---+ + * | | + * L | (+) P | R <-- probe (20,20) + * E | | I + * F | (-) N (+) | G <-- nozzle (10,10) + * T | | H + * | (-) | T + * | | + * O-- FRONT --+ + * (0,0) + */ +#define X_PROBE_OFFSET_FROM_EXTRUDER -23 // KosselPro actual: -22.919 +#define Y_PROBE_OFFSET_FROM_EXTRUDER -6 // KosselPro actual: -6.304 +/** + * Kossel Pro note: The correct value is likely -17.45 but I'd rather err on the side of + * not giving someone a head crash. Use something like G29 Z-0.2 to adjust as needed. + */ +#define Z_PROBE_OFFSET_FROM_EXTRUDER -17.25 // Increase this if the first layer is too thin (remember: it's a negative number so increase means closer to zero). +// Certain types of probes need to stay away from edges +#define MIN_PROBE_EDGE 10 + +// X and Y axis travel speed (mm/m) between probes +#define XY_PROBE_SPEED 8000 + +// Feedrate (mm/m) for the first approach when double-probing (MULTIPLE_PROBING == 2) +#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z + +// Feedrate (mm/m) for the "accurate" probe of each point +#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2) + +// The number of probes to perform at each point. +// Set to 2 for a fast/slow probe, using the second probe result. +// Set to 3 or more for slow probes, averaging the results. +//#define MULTIPLE_PROBING 2 + /** * Z probes require clearance when deploying, stowing, and moving between * probe points to avoid hitting the bed and other hardware. @@ -986,6 +968,20 @@ // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/delta/kossel_xl/Configuration.h b/Marlin/src/config/examples/delta/kossel_xl/Configuration.h index cbab083ead..c334972792 100644 --- a/Marlin/src/config/examples/delta/kossel_xl/Configuration.h +++ b/Marlin/src/config/examples/delta/kossel_xl/Configuration.h @@ -846,20 +846,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -867,50 +853,6 @@ //#define Z_PROBE_SLED //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. -// -// For Z_PROBE_ALLEN_KEY see the Delta example configurations. -// - -/** - * Z Probe to nozzle (X,Y) offset, relative to (0, 0). - * X and Y offsets must be integers. - * - * In the following example the X and Y offsets are both positive: - * #define X_PROBE_OFFSET_FROM_EXTRUDER 10 - * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 - * - * +-- BACK ---+ - * | | - * L | (+) P | R <-- probe (20,20) - * E | | I - * F | (-) N (+) | G <-- nozzle (10,10) - * T | | H - * | (-) | T - * | | - * O-- FRONT --+ - * (0,0) - */ -#define X_PROBE_OFFSET_FROM_EXTRUDER 0.0 // Z probe to nozzle X offset: -left +right -#define Y_PROBE_OFFSET_FROM_EXTRUDER 0.0 // Z probe to nozzle Y offset: -front +behind -#define Z_PROBE_OFFSET_FROM_EXTRUDER 0.3 // Z probe to nozzle Z offset: -below (always!) - -// Certain types of probes need to stay away from edges -#define MIN_PROBE_EDGE 10 - -// X and Y axis travel speed (mm/m) between probes -#define XY_PROBE_SPEED 8000 - -// Feedrate (mm/m) for the first approach when double-probing (MULTIPLE_PROBING == 2) -#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z - -// Feedrate (mm/m) for the "accurate" probe of each point -#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2) - -// The number of probes to perform at each point. -// Set to 2 for a fast/slow probe, using the second probe result. -// Set to 3 or more for slow probes, averaging the results. -//#define MULTIPLE_PROBING 2 - /** * Allen key retractable z-probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe * Deploys by touching z-axis belt. Retracts by pushing the probe down. Uses Z_MIN_PIN. @@ -958,6 +900,46 @@ #endif // Z_PROBE_ALLEN_KEY +/** + * Z Probe to nozzle (X,Y) offset, relative to (0, 0). + * X and Y offsets must be integers. + * + * In the following example the X and Y offsets are both positive: + * #define X_PROBE_OFFSET_FROM_EXTRUDER 10 + * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 + * + * +-- BACK ---+ + * | | + * L | (+) P | R <-- probe (20,20) + * E | | I + * F | (-) N (+) | G <-- nozzle (10,10) + * T | | H + * | (-) | T + * | | + * O-- FRONT --+ + * (0,0) + */ +#define X_PROBE_OFFSET_FROM_EXTRUDER 0.0 // Z probe to nozzle X offset: -left +right +#define Y_PROBE_OFFSET_FROM_EXTRUDER 0.0 // Z probe to nozzle Y offset: -front +behind +#define Z_PROBE_OFFSET_FROM_EXTRUDER 0.3 // Z probe to nozzle Z offset: -below (always!) + +// Certain types of probes need to stay away from edges +#define MIN_PROBE_EDGE 10 + +// X and Y axis travel speed (mm/m) between probes +#define XY_PROBE_SPEED 8000 + +// Feedrate (mm/m) for the first approach when double-probing (MULTIPLE_PROBING == 2) +#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z + +// Feedrate (mm/m) for the "accurate" probe of each point +#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2) + +// The number of probes to perform at each point. +// Set to 2 for a fast/slow probe, using the second probe result. +// Set to 3 or more for slow probes, averaging the results. +//#define MULTIPLE_PROBING 2 + /** * Z probes require clearance when deploying, stowing, and moving between * probe points to avoid hitting the bed and other hardware. @@ -986,6 +968,20 @@ // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration.h b/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration.h index 0ed4fe3c82..176c1da98f 100644 --- a/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration.h +++ b/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration.h @@ -784,20 +784,6 @@ #define BLTOUCH_DELAY 500 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -877,6 +863,20 @@ // Enable the M48 repeatability test to test probe accuracy #define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/makibox/Configuration.h b/Marlin/src/config/examples/makibox/Configuration.h index 1bab0b4baa..5266f7ac02 100644 --- a/Marlin/src/config/examples/makibox/Configuration.h +++ b/Marlin/src/config/examples/makibox/Configuration.h @@ -774,20 +774,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -867,6 +853,20 @@ // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/stm32f103ret6/Configuration.h b/Marlin/src/config/examples/stm32f103ret6/Configuration.h index cf400964ce..49fb96b574 100644 --- a/Marlin/src/config/examples/stm32f103ret6/Configuration.h +++ b/Marlin/src/config/examples/stm32f103ret6/Configuration.h @@ -773,20 +773,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -866,6 +852,20 @@ // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/Marlin/src/config/examples/tvrrug/Round2/Configuration.h b/Marlin/src/config/examples/tvrrug/Round2/Configuration.h index ed16fd6dc5..c2830ad1e7 100644 --- a/Marlin/src/config/examples/tvrrug/Round2/Configuration.h +++ b/Marlin/src/config/examples/tvrrug/Round2/Configuration.h @@ -766,20 +766,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -859,6 +845,20 @@ // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 1 diff --git a/Marlin/src/config/examples/wt150/Configuration.h b/Marlin/src/config/examples/wt150/Configuration.h index fe879e29fd..e748c5b8d3 100644 --- a/Marlin/src/config/examples/wt150/Configuration.h +++ b/Marlin/src/config/examples/wt150/Configuration.h @@ -776,20 +776,6 @@ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed #endif -/** - * Enable one or more of the following if probing seems unreliable. - * Heaters and/or fans can be disabled during probing to minimize electrical - * noise. A delay can also be added to allow noise and vibration to settle. - * These options are most useful for the BLTouch probe, but may also improve - * readings with inductive probes and piezo sensors. - */ -//#define PROBING_HEATERS_OFF // Turn heaters off when probing -#if ENABLED(PROBING_HEATERS_OFF) - //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) -#endif -//#define PROBING_FANS_OFF // Turn fans off when probing -//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors - // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE @@ -869,6 +855,20 @@ // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0