diff --git a/Marlin/src/HAL/HAL_AVR/HAL.h b/Marlin/src/HAL/HAL_AVR/HAL.h index 9cdcab56fd..b887e6df27 100644 --- a/Marlin/src/HAL/HAL_AVR/HAL.h +++ b/Marlin/src/HAL/HAL_AVR/HAL.h @@ -108,10 +108,6 @@ extern "C" { int freeMemory(void); } -// eeprom -//void eeprom_write_byte(unsigned char *pos, unsigned char value); -//unsigned char eeprom_read_byte(unsigned char *pos); - // timers #define HAL_TIMER_RATE ((F_CPU) / 8) // i.e., 2MHz or 2.5MHz @@ -119,20 +115,15 @@ extern "C" { #define TEMP_TIMER_NUM 0 #define PULSE_TIMER_NUM STEP_TIMER_NUM -#define STEPPER_TIMER_RATE HAL_TIMER_RATE -#define HAL_TICKS_PER_US ((STEPPER_TIMER_RATE) / 1000000) // Cannot be of type double -#define STEPPER_TIMER_PRESCALE 8 -#define STEP_TIMER_MIN_INTERVAL 8 // minimum time in µs between stepper interrupts - #define TEMP_TIMER_FREQUENCY ((F_CPU) / 64.0 / 256.0) -#define TIMER_OCR_1 OCR1A -#define TIMER_COUNTER_1 TCNT1 - -#define TIMER_OCR_0 OCR0A -#define TIMER_COUNTER_0 TCNT0 +#define STEPPER_TIMER_RATE HAL_TIMER_RATE +#define STEPPER_TIMER_PRESCALE 8 +#define STEPPER_TIMER_TICKS_PER_US ((STEPPER_TIMER_RATE) / 1000000) // Cannot be of type double -#define PULSE_TIMER_PRESCALE STEPPER_TIMER_PRESCALE +#define PULSE_TIMER_RATE STEPPER_TIMER_RATE // frequency of pulse timer +#define PULSE_TIMER_PRESCALE STEPPER_TIMER_PRESCALE +#define PULSE_TIMER_TICKS_PER_US STEPPER_TIMER_TICKS_PER_US #define ENABLE_STEPPER_DRIVER_INTERRUPT() SBI(TIMSK1, OCIE1A) #define DISABLE_STEPPER_DRIVER_INTERRUPT() CBI(TIMSK1, OCIE1A) @@ -173,6 +164,12 @@ FORCE_INLINE void HAL_timer_start(const uint8_t timer_num, const uint32_t freque } } +#define TIMER_OCR_1 OCR1A +#define TIMER_COUNTER_1 TCNT1 + +#define TIMER_OCR_0 OCR0A +#define TIMER_COUNTER_0 TCNT0 + #define _CAT(a, ...) a ## __VA_ARGS__ #define HAL_timer_set_compare(timer, compare) (_CAT(TIMER_OCR_, timer) = compare) #define HAL_timer_restrain(timer, interval_ticks) NOLESS(_CAT(TIMER_OCR_, timer), _CAT(TIMER_COUNTER_, timer) + interval_ticks) diff --git a/Marlin/src/HAL/HAL_DUE/HAL_timers_Due.h b/Marlin/src/HAL/HAL_DUE/HAL_timers_Due.h index cfa20aa35c..871ef995e6 100644 --- a/Marlin/src/HAL/HAL_DUE/HAL_timers_Due.h +++ b/Marlin/src/HAL/HAL_DUE/HAL_timers_Due.h @@ -43,21 +43,22 @@ typedef uint32_t hal_timer_t; #define HAL_TIMER_TYPE_MAX 0xFFFFFFFF +#define HAL_TIMER_RATE ((F_CPU) / 2) // frequency of timers peripherals + #define STEP_TIMER_NUM 3 // index of timer to use for stepper #define TEMP_TIMER_NUM 4 // index of timer to use for temperature +#define PULSE_TIMER_NUM STEP_TIMER_NUM #define TONE_TIMER_NUM 6 // index of timer to use for beeper tones -#define HAL_TIMER_RATE ((F_CPU) / 2) // frequency of timers peripherals +#define TEMP_TIMER_FREQUENCY 1000 // temperature interrupt frequency #define STEPPER_TIMER_RATE HAL_TIMER_RATE // frequency of stepper timer (HAL_TIMER_RATE / STEPPER_TIMER_PRESCALE) -#define HAL_TICKS_PER_US ((STEPPER_TIMER_RATE) / 1000000) // stepper timer ticks per µs -#define STEPPER_TIMER_PRESCALE (CYCLES_PER_MICROSECOND / HAL_TICKS_PER_US) -#define STEP_TIMER_MIN_INTERVAL 8 // minimum time in µs between stepper interrupts - -#define TEMP_TIMER_FREQUENCY 1000 // temperature interrupt frequency +#define STEPPER_TIMER_TICKS_PER_US ((STEPPER_TIMER_RATE) / 1000000) // stepper timer ticks per µs +#define STEPPER_TIMER_PRESCALE (CYCLES_PER_MICROSECOND / STEPPER_TIMER_TICKS_PER_US) -#define PULSE_TIMER_NUM STEP_TIMER_NUM -#define PULSE_TIMER_PRESCALE STEPPER_TIMER_PRESCALE +#define PULSE_TIMER_RATE STEPPER_TIMER_RATE // frequency of pulse timer +#define PULSE_TIMER_PRESCALE STEPPER_TIMER_PRESCALE +#define PULSE_TIMER_TICKS_PER_US STEPPER_TIMER_TICKS_PER_US #define ENABLE_STEPPER_DRIVER_INTERRUPT() HAL_timer_enable_interrupt(STEP_TIMER_NUM) #define DISABLE_STEPPER_DRIVER_INTERRUPT() HAL_timer_disable_interrupt(STEP_TIMER_NUM) diff --git a/Marlin/src/HAL/HAL_LPC1768/HAL_timers.h b/Marlin/src/HAL/HAL_LPC1768/HAL_timers.h index ad3706c560..2113335385 100644 --- a/Marlin/src/HAL/HAL_LPC1768/HAL_timers.h +++ b/Marlin/src/HAL/HAL_LPC1768/HAL_timers.h @@ -66,22 +66,23 @@ typedef uint32_t hal_timer_t; #define HAL_TIMER_TYPE_MAX 0xFFFFFFFF +#define HAL_TIMER_RATE ((SystemCoreClock) / 4) // frequency of timers peripherals + #define STEP_TIMER_NUM 0 // Timer Index for Stepper #define TEMP_TIMER_NUM 1 // Timer Index for Temperature #define PULSE_TIMER_NUM STEP_TIMER_NUM #define PWM_TIMER_NUM 3 // Timer Index for PWM -#define HAL_TIMER_RATE ((SystemCoreClock) / 4) // frequency of timers peripherals -#define STEPPER_TIMER_RATE HAL_TIMER_RATE // frequency of stepper timer (HAL_TIMER_RATE / STEPPER_TIMER_PRESCALE) -#define HAL_TICKS_PER_US ((STEPPER_TIMER_RATE) / 1000000) // stepper timer ticks per µs -#define STEPPER_TIMER_PRESCALE (CYCLES_PER_MICROSECOND / HAL_TICKS_PER_US) - -#define STEP_TIMER_MIN_INTERVAL 8 // minimum time in µs between stepper interrupts - #define TEMP_TIMER_RATE 1000000 #define TEMP_TIMER_FREQUENCY 1000 // temperature interrupt frequency -#define PULSE_TIMER_PRESCALE STEPPER_TIMER_PRESCALE +#define STEPPER_TIMER_RATE HAL_TIMER_RATE // frequency of stepper timer (HAL_TIMER_RATE / STEPPER_TIMER_PRESCALE) +#define STEPPER_TIMER_TICKS_PER_US ((STEPPER_TIMER_RATE) / 1000000) // stepper timer ticks per µs +#define STEPPER_TIMER_PRESCALE (CYCLES_PER_MICROSECOND / STEPPER_TIMER_TICKS_PER_US) + +#define PULSE_TIMER_RATE STEPPER_TIMER_RATE // frequency of pulse timer +#define PULSE_TIMER_PRESCALE STEPPER_TIMER_PRESCALE +#define PULSE_TIMER_TICKS_PER_US STEPPER_TIMER_TICKS_PER_US #define ENABLE_STEPPER_DRIVER_INTERRUPT() HAL_timer_enable_interrupt(STEP_TIMER_NUM) #define DISABLE_STEPPER_DRIVER_INTERRUPT() HAL_timer_disable_interrupt(STEP_TIMER_NUM) diff --git a/Marlin/src/HAL/HAL_STM32F1/HAL_timers_Stm32f1.h b/Marlin/src/HAL/HAL_STM32F1/HAL_timers_Stm32f1.h index c6fce545e3..132cf4d22f 100644 --- a/Marlin/src/HAL/HAL_STM32F1/HAL_timers_Stm32f1.h +++ b/Marlin/src/HAL/HAL_STM32F1/HAL_timers_Stm32f1.h @@ -47,37 +47,34 @@ typedef uint16_t hal_timer_t; #define HAL_TIMER_TYPE_MAX 0xFFFF +#define HAL_TIMER_RATE (F_CPU) // frequency of timers peripherals + +#define STEP_TIMER_CHAN 1 // Channel of the timer to use for compare and interrupts +#define TEMP_TIMER_CHAN 1 // Channel of the timer to use for compare and interrupts + #if defined(MCU_STM32F103CB) || defined(MCU_STM32F103C8) #define STEP_TIMER_NUM 4 // For C8/CB boards, use timer 4 #else #define STEP_TIMER_NUM 5 // for other boards, five is fine. #endif - -#define STEP_TIMER_CHAN 1 // Channel of the timer to use for compare and interrupts #define TEMP_TIMER_NUM 2 // index of timer to use for temperature -#define TEMP_TIMER_CHAN 1 // Channel of the timer to use for compare and interrupts #define PULSE_TIMER_NUM STEP_TIMER_NUM -timer_dev* get_timer_dev(int number); - -#define TIMER_DEV(num) get_timer_dev(num) - -#define STEP_TIMER_DEV TIMER_DEV(STEP_TIMER_NUM) -#define TEMP_TIMER_DEV TIMER_DEV(TEMP_TIMER_NUM) - -//STM32_HAVE_TIMER(n); +#define TEMP_TIMER_PRESCALE 1000 // prescaler for setting Temp timer, 72Khz +#define TEMP_TIMER_FREQUENCY 1000 // temperature interrupt frequency -#define HAL_TIMER_RATE (F_CPU) // frequency of timers peripherals #define STEPPER_TIMER_PRESCALE 18 // prescaler for setting stepper timer, 4Mhz #define STEPPER_TIMER_RATE (HAL_TIMER_RATE / STEPPER_TIMER_PRESCALE) // frequency of stepper timer -#define HAL_TICKS_PER_US ((STEPPER_TIMER_RATE) / 1000000) // stepper timer ticks per µs - -#define PULSE_TIMER_PRESCALE STEPPER_TIMER_PRESCALE +#define STEPPER_TIMER_TICKS_PER_US ((STEPPER_TIMER_RATE) / 1000000) // stepper timer ticks per µs -#define TEMP_TIMER_PRESCALE 1000 // prescaler for setting Temp timer, 72Khz -#define TEMP_TIMER_FREQUENCY 1000 // temperature interrupt frequency +#define PULSE_TIMER_RATE STEPPER_TIMER_RATE // frequency of pulse timer +#define PULSE_TIMER_PRESCALE STEPPER_TIMER_PRESCALE +#define PULSE_TIMER_TICKS_PER_US STEPPER_TIMER_TICKS_PER_US -#define STEP_TIMER_MIN_INTERVAL 8 // minimum time in µs between stepper interrupts +timer_dev* get_timer_dev(int number); +#define TIMER_DEV(num) get_timer_dev(num) +#define STEP_TIMER_DEV TIMER_DEV(STEP_TIMER_NUM) +#define TEMP_TIMER_DEV TIMER_DEV(TEMP_TIMER_NUM) #define ENABLE_STEPPER_DRIVER_INTERRUPT() timer_enable_irq(STEP_TIMER_DEV, STEP_TIMER_CHAN) #define DISABLE_STEPPER_DRIVER_INTERRUPT() timer_disable_irq(STEP_TIMER_DEV, STEP_TIMER_CHAN) diff --git a/Marlin/src/HAL/HAL_STM32F4/HAL_timers_STM32F4.h b/Marlin/src/HAL/HAL_STM32F4/HAL_timers_STM32F4.h index 982d05d576..943550d13f 100644 --- a/Marlin/src/HAL/HAL_STM32F4/HAL_timers_STM32F4.h +++ b/Marlin/src/HAL/HAL_STM32F4/HAL_timers_STM32F4.h @@ -38,21 +38,22 @@ #define hal_timer_t uint32_t // TODO: One is 16-bit, one 32-bit - does this need to be checked? #define HAL_TIMER_TYPE_MAX 0xFFFF -#define STEP_TIMER_NUM 0 // index of timer to use for stepper -#define TEMP_TIMER_NUM 1 // index of timer to use for temperature - #define HAL_TIMER_RATE (HAL_RCC_GetSysClockFreq() / 2) // frequency of timer peripherals -#define STEPPER_TIMER_PRESCALE 54 // was 40,prescaler for setting stepper timer, 2Mhz -#define STEPPER_TIMER_RATE (HAL_TIMER_RATE / STEPPER_TIMER_PRESCALE) // frequency of stepper timer -#define HAL_TICKS_PER_US ((STEPPER_TIMER_RATE) / 1000000) // stepper timer ticks per µs +#define STEP_TIMER_NUM 0 // index of timer to use for stepper +#define TEMP_TIMER_NUM 1 // index of timer to use for temperature #define PULSE_TIMER_NUM STEP_TIMER_NUM -#define PULSE_TIMER_PRESCALE STEPPER_TIMER_PRESCALE #define TEMP_TIMER_PRESCALE 1000 // prescaler for setting Temp timer, 72Khz #define TEMP_TIMER_FREQUENCY 1000 // temperature interrupt frequency -#define STEP_TIMER_MIN_INTERVAL 8 // minimum time in µs between stepper interrupts +#define STEPPER_TIMER_PRESCALE 54 // was 40,prescaler for setting stepper timer, 2Mhz +#define STEPPER_TIMER_RATE (HAL_TIMER_RATE / STEPPER_TIMER_PRESCALE) // frequency of stepper timer +#define STEPPER_TIMER_TICKS_PER_US ((STEPPER_TIMER_RATE) / 1000000) // stepper timer ticks per µs + +#define PULSE_TIMER_RATE STEPPER_TIMER_RATE // frequency of pulse timer +#define PULSE_TIMER_PRESCALE STEPPER_TIMER_PRESCALE +#define PULSE_TIMER_TICKS_PER_US STEPPER_TIMER_TICKS_PER_US #define ENABLE_STEPPER_DRIVER_INTERRUPT() HAL_timer_enable_interrupt(STEP_TIMER_NUM) #define DISABLE_STEPPER_DRIVER_INTERRUPT() HAL_timer_disable_interrupt(STEP_TIMER_NUM) diff --git a/Marlin/src/HAL/HAL_STM32F7/HAL_timers_STM32F7.h b/Marlin/src/HAL/HAL_STM32F7/HAL_timers_STM32F7.h index 132e93aa56..a97bad75fb 100644 --- a/Marlin/src/HAL/HAL_STM32F7/HAL_timers_STM32F7.h +++ b/Marlin/src/HAL/HAL_STM32F7/HAL_timers_STM32F7.h @@ -38,21 +38,22 @@ #define hal_timer_t uint32_t // TODO: One is 16-bit, one 32-bit - does this need to be checked? #define HAL_TIMER_TYPE_MAX 0xFFFF -#define STEP_TIMER_NUM 0 // index of timer to use for stepper -#define TEMP_TIMER_NUM 1 // index of timer to use for temperature - #define HAL_TIMER_RATE (HAL_RCC_GetSysClockFreq() / 2) // frequency of timer peripherals -#define STEPPER_TIMER_PRESCALE 54 // was 40,prescaler for setting stepper timer, 2Mhz -#define STEPPER_TIMER_RATE (HAL_TIMER_RATE / STEPPER_TIMER_PRESCALE) // frequency of stepper timer -#define HAL_TICKS_PER_US ((STEPPER_TIMER_RATE) / 1000000) // stepper timer ticks per µs +#define STEP_TIMER_NUM 0 // index of timer to use for stepper +#define TEMP_TIMER_NUM 1 // index of timer to use for temperature #define PULSE_TIMER_NUM STEP_TIMER_NUM -#define PULSE_TIMER_PRESCALE STEPPER_TIMER_PRESCALE -#define TEMP_TIMER_PRESCALE 1000 // prescaler for setting Temp timer, 72Khz #define TEMP_TIMER_FREQUENCY 1000 // temperature interrupt frequency +#define TEMP_TIMER_PRESCALE 1000 // prescaler for setting Temp timer, 72Khz + +#define STEPPER_TIMER_PRESCALE 54 // was 40,prescaler for setting stepper timer, 2Mhz +#define STEPPER_TIMER_RATE (HAL_TIMER_RATE / STEPPER_TIMER_PRESCALE) // frequency of stepper timer +#define STEPPER_TIMER_TICKS_PER_US ((STEPPER_TIMER_RATE) / 1000000) // stepper timer ticks per µs -#define STEP_TIMER_MIN_INTERVAL 8 // minimum time in µs between stepper interrupts +#define PULSE_TIMER_RATE STEPPER_TIMER_RATE // frequency of pulse timer +#define PULSE_TIMER_PRESCALE STEPPER_TIMER_PRESCALE +#define PULSE_TIMER_TICKS_PER_US STEPPER_TIMER_TICKS_PER_US #define ENABLE_STEPPER_DRIVER_INTERRUPT() HAL_timer_enable_interrupt(STEP_TIMER_NUM) #define DISABLE_STEPPER_DRIVER_INTERRUPT() HAL_timer_disable_interrupt(STEP_TIMER_NUM) diff --git a/Marlin/src/HAL/HAL_TEENSY35_36/HAL_timers_Teensy.h b/Marlin/src/HAL/HAL_TEENSY35_36/HAL_timers_Teensy.h index 2891fb8fdd..5fed19e313 100644 --- a/Marlin/src/HAL/HAL_TEENSY35_36/HAL_timers_Teensy.h +++ b/Marlin/src/HAL/HAL_TEENSY35_36/HAL_timers_Teensy.h @@ -43,10 +43,6 @@ typedef uint32_t hal_timer_t; #define HAL_TIMER_TYPE_MAX 0xFFFFFFFF -#define STEP_TIMER_NUM 0 -#define TEMP_TIMER_NUM 1 -#define PULSE_TIMER_NUM STEP_TIMER_NUM - #define FTM0_TIMER_PRESCALE 8 #define FTM1_TIMER_PRESCALE 4 #define FTM0_TIMER_PRESCALE_BITS 0b011 @@ -56,14 +52,20 @@ typedef uint32_t hal_timer_t; #define FTM1_TIMER_RATE (F_BUS / FTM1_TIMER_PRESCALE) // 60MHz / 4 = 15MHz #define HAL_TIMER_RATE (FTM0_TIMER_RATE) -#define STEPPER_TIMER_RATE HAL_TIMER_RATE -#define HAL_TICKS_PER_US ((STEPPER_TIMER_RATE) / 1000000) -#define STEPPER_TIMER_PRESCALE (CYCLES_PER_MICROSECOND / HAL_TICKS_PER_US) -#define STEP_TIMER_MIN_INTERVAL 8 // minimum time in µs between stepper interrupts -#define TEMP_TIMER_FREQUENCY 1000 +#define STEP_TIMER_NUM 0 +#define TEMP_TIMER_NUM 1 +#define PULSE_TIMER_NUM STEP_TIMER_NUM + +#define TEMP_TIMER_FREQUENCY 1000 + +#define STEPPER_TIMER_RATE HAL_TIMER_RATE +#define STEPPER_TIMER_TICKS_PER_US ((STEPPER_TIMER_RATE) / 1000000) +#define STEPPER_TIMER_PRESCALE (CYCLES_PER_MICROSECOND / STEPPER_TIMER_TICKS_PER_US) -#define PULSE_TIMER_PRESCALE STEPPER_TIMER_PRESCALE +#define PULSE_TIMER_RATE STEPPER_TIMER_RATE // frequency of pulse timer +#define PULSE_TIMER_PRESCALE STEPPER_TIMER_PRESCALE +#define PULSE_TIMER_TICKS_PER_US STEPPER_TIMER_TICKS_PER_US #define ENABLE_STEPPER_DRIVER_INTERRUPT() HAL_timer_enable_interrupt(STEP_TIMER_NUM) #define DISABLE_STEPPER_DRIVER_INTERRUPT() HAL_timer_disable_interrupt(STEP_TIMER_NUM) diff --git a/Marlin/src/inc/Conditionals_post.h b/Marlin/src/inc/Conditionals_post.h index dd018a1154..0f6feb1a90 100644 --- a/Marlin/src/inc/Conditionals_post.h +++ b/Marlin/src/inc/Conditionals_post.h @@ -1444,149 +1444,4 @@ #define USE_EXECUTE_COMMANDS_IMMEDIATE #endif -// Calculate a default maximum stepper rate, if not supplied -#ifndef MAXIMUM_STEPPER_RATE - #if MINIMUM_STEPPER_PULSE - #define MAXIMUM_STEPPER_RATE (1000000UL / (2UL * (MINIMUM_STEPPER_PULSE))) - #else - #define MAXIMUM_STEPPER_RATE 500000UL - #endif -#endif - -// -// Estimate the amount of time the ISR will take to execute -// -#ifdef CPU_32_BIT - - // The base ISR takes 792 cycles - #define ISR_BASE_CYCLES 792UL - - // Linear advance base time is 64 cycles - #if ENABLED(LIN_ADVANCE) - #define ISR_LA_BASE_CYCLES 64UL - #else - #define ISR_LA_BASE_CYCLES 0UL - #endif - - // S curve interpolation adds 40 cycles - #if ENABLED(S_CURVE_ACCELERATION) - #define ISR_S_CURVE_CYCLES 40UL - #else - #define ISR_S_CURVE_CYCLES 0UL - #endif - - // Stepper Loop base cycles - #define ISR_LOOP_BASE_CYCLES 4UL - - // And each stepper takes 16 cycles - #define ISR_STEPPER_CYCLES 16UL - -#else - - // The base ISR takes 752 cycles - #define ISR_BASE_CYCLES 752UL - - // Linear advance base time is 32 cycles - #if ENABLED(LIN_ADVANCE) - #define ISR_LA_BASE_CYCLES 32UL - #else - #define ISR_LA_BASE_CYCLES 0UL - #endif - - // S curve interpolation adds 160 cycles - #if ENABLED(S_CURVE_ACCELERATION) - #define ISR_S_CURVE_CYCLES 160UL - #else - #define ISR_S_CURVE_CYCLES 0UL - #endif - - // Stepper Loop base cycles - #define ISR_LOOP_BASE_CYCLES 32UL - - // And each stepper takes 88 cycles - #define ISR_STEPPER_CYCLES 88UL - -#endif - -// For each stepper, we add its time -#ifdef HAS_X_STEP - #define ISR_X_STEPPER_CYCLES ISR_STEPPER_CYCLES -#else - #define ISR_X_STEPPER_CYCLES 0UL -#endif - -// For each stepper, we add its time -#ifdef HAS_Y_STEP - #define ISR_Y_STEPPER_CYCLES ISR_STEPPER_CYCLES -#else - #define ISR_Y_STEPPER_CYCLES 0UL -#endif - -// For each stepper, we add its time -#ifdef HAS_Z_STEP - #define ISR_Z_STEPPER_CYCLES ISR_STEPPER_CYCLES -#else - #define ISR_Z_STEPPER_CYCLES 0UL -#endif - -// E is always interpolated, even for mixing extruders -#define ISR_E_STEPPER_CYCLES ISR_STEPPER_CYCLES - -// If linear advance is disabled, then the loop also handles them -#if DISABLED(LIN_ADVANCE) && ENABLED(MIXING_EXTRUDER) - #define ISR_MIXING_STEPPER_CYCLES ((MIXING_STEPPERS) * ISR_STEPPER_CYCLES) -#else - #define ISR_MIXING_STEPPER_CYCLES 0UL -#endif - -// And the total minimum loop time is, without including the base -#define MIN_ISR_LOOP_CYCLES (ISR_X_STEPPER_CYCLES + ISR_Y_STEPPER_CYCLES + ISR_Z_STEPPER_CYCLES + ISR_E_STEPPER_CYCLES + ISR_MIXING_STEPPER_CYCLES) - -// Calculate the minimum MPU cycles needed per pulse to enforce not surpassing the maximum stepper rate -#define _MIN_STEPPER_PULSE_CYCLES(N) MAX((F_CPU) / (MAXIMUM_STEPPER_RATE), ((F_CPU) / 500000UL) * (N)) -#if MINIMUM_STEPPER_PULSE - #define MIN_STEPPER_PULSE_CYCLES _MIN_STEPPER_PULSE_CYCLES(MINIMUM_STEPPER_PULSE) -#else - #define MIN_STEPPER_PULSE_CYCLES _MIN_STEPPER_PULSE_CYCLES(1) -#endif - -// But the user could be enforcing a minimum time, so the loop time is -#define ISR_LOOP_CYCLES (ISR_LOOP_BASE_CYCLES + MAX(MIN_STEPPER_PULSE_CYCLES, MIN_ISR_LOOP_CYCLES)) - -// If linear advance is enabled, then it is handled separately -#if ENABLED(LIN_ADVANCE) - - // Estimate the minimum LA loop time - #if ENABLED(MIXING_EXTRUDER) - #define MIN_ISR_LA_LOOP_CYCLES ((MIXING_STEPPERS) * (ISR_STEPPER_CYCLES)) - #else - #define MIN_ISR_LA_LOOP_CYCLES ISR_STEPPER_CYCLES - #endif - - // And the real loop time - #define ISR_LA_LOOP_CYCLES MAX(MIN_STEPPER_PULSE_CYCLES, MIN_ISR_LA_LOOP_CYCLES) - -#else - #define ISR_LA_LOOP_CYCLES 0UL -#endif - -// Now estimate the total ISR execution time in cycles given a step per ISR multiplier -#define ISR_EXECUTION_CYCLES(rate) (((ISR_BASE_CYCLES + ISR_S_CURVE_CYCLES + (ISR_LOOP_CYCLES * rate) + ISR_LA_BASE_CYCLES + ISR_LA_LOOP_CYCLES)) / rate) - -// The maximum allowable stepping frequency when doing x128-x1 stepping (in Hz) -#define MAX_128X_STEP_ISR_FREQUENCY (F_CPU / ISR_EXECUTION_CYCLES(128)) -#define MAX_64X_STEP_ISR_FREQUENCY (F_CPU / ISR_EXECUTION_CYCLES(64)) -#define MAX_32X_STEP_ISR_FREQUENCY (F_CPU / ISR_EXECUTION_CYCLES(32)) -#define MAX_16X_STEP_ISR_FREQUENCY (F_CPU / ISR_EXECUTION_CYCLES(16)) -#define MAX_8X_STEP_ISR_FREQUENCY (F_CPU / ISR_EXECUTION_CYCLES(8)) -#define MAX_4X_STEP_ISR_FREQUENCY (F_CPU / ISR_EXECUTION_CYCLES(4)) -#define MAX_2X_STEP_ISR_FREQUENCY (F_CPU / ISR_EXECUTION_CYCLES(2)) -#define MAX_1X_STEP_ISR_FREQUENCY (F_CPU / ISR_EXECUTION_CYCLES(1)) - -// The minimum allowable frequency for step smoothing will be 1/10 of the maximum nominal frequency (in Hz) -#define MIN_STEP_ISR_FREQUENCY MAX_1X_STEP_ISR_FREQUENCY - -// Disable multiple steps per ISR -//#define DISABLE_MULTI_STEPPING - #endif // CONDITIONALS_POST_H diff --git a/Marlin/src/module/stepper.cpp b/Marlin/src/module/stepper.cpp index feb75fbd34..369cadfb54 100644 --- a/Marlin/src/module/stepper.cpp +++ b/Marlin/src/module/stepper.cpp @@ -1263,7 +1263,7 @@ void Stepper::isr() { #else 1 #endif - * (HAL_TICKS_PER_US) + * (STEPPER_TIMER_TICKS_PER_US) ); /** @@ -1316,10 +1316,10 @@ void Stepper::stepper_pulse_phase_isr() { // Just update the value we will get at the end of the loop step_events_completed += events_to_do; - #if MINIMUM_STEPPER_PULSE - // Get the timer count and estimate the end of the pulse - hal_timer_t pulse_end = HAL_timer_get_count(PULSE_TIMER_NUM) + hal_timer_t((HAL_TICKS_PER_US) * (MINIMUM_STEPPER_PULSE)); - #endif + // Get the timer count and estimate the end of the pulse + hal_timer_t pulse_end = HAL_timer_get_count(PULSE_TIMER_NUM) + hal_timer_t(MIN_PULSE_TICKS); + + const hal_timer_t added_step_ticks = ADDED_STEP_TICKS; // Take multiple steps per interrupt (For high speed moves) do { @@ -1392,10 +1392,11 @@ void Stepper::stepper_pulse_phase_isr() { #if MINIMUM_STEPPER_PULSE // Just wait for the requested pulse duration while (HAL_timer_get_count(PULSE_TIMER_NUM) < pulse_end) { /* nada */ } - // Add to the value, the value needed for the pulse end and ensuring the maximum driver rate is enforced - pulse_end += hal_timer_t(MIN_STEPPER_PULSE_CYCLES) - hal_timer_t((HAL_TICKS_PER_US) * (MINIMUM_STEPPER_PULSE)); #endif + // Add the delay needed to ensure the maximum driver rate is enforced + if (signed(added_step_ticks) > 0) pulse_end += hal_timer_t(added_step_ticks); + // Pulse stop #if HAS_X_STEP PULSE_STOP(X); @@ -1423,15 +1424,15 @@ void Stepper::stepper_pulse_phase_isr() { // Decrement the count of pending pulses to do --events_to_do; - #if MINIMUM_STEPPER_PULSE - // For minimum pulse time wait after stopping pulses also - if (events_to_do) { - // Just wait for the requested pulse duration - while (HAL_timer_get_count(PULSE_TIMER_NUM) < pulse_end) { /* nada */ } + // For minimum pulse time wait after stopping pulses also + if (events_to_do) { + // Just wait for the requested pulse duration + while (HAL_timer_get_count(PULSE_TIMER_NUM) < pulse_end) { /* nada */ } + #if MINIMUM_STEPPER_PULSE // Add to the value, the time that the pulse must be active (to be used on the next loop) - pulse_end += hal_timer_t((HAL_TICKS_PER_US) * (MINIMUM_STEPPER_PULSE)); - } - #endif + pulse_end += hal_timer_t(MIN_PULSE_TICKS); + #endif + } } while (events_to_do); } @@ -1664,7 +1665,7 @@ uint32_t Stepper::stepper_block_phase_isr() { uint32_t max_rate = current_block->nominal_rate; // Get the maximum rate (maximum event speed) while (max_rate < MIN_STEP_ISR_FREQUENCY) { max_rate <<= 1; - if (max_rate >= MAX_1X_STEP_ISR_FREQUENCY) break; + if (max_rate >= MAX_STEP_ISR_FREQUENCY_1X) break; ++oversampling; } oversampling_factor = oversampling; @@ -1810,13 +1811,15 @@ uint32_t Stepper::stepper_block_phase_isr() { REV_E_DIR(active_extruder); #endif + // Get the timer count and estimate the end of the pulse + hal_timer_t pulse_end = HAL_timer_get_count(PULSE_TIMER_NUM) + hal_timer_t(MIN_PULSE_TICKS); + + const hal_timer_t added_step_ticks = ADDED_STEP_TICKS; + // Step E stepper if we have steps while (LA_steps) { - #if MINIMUM_STEPPER_PULSE - hal_timer_t pulse_end = HAL_timer_get_count(PULSE_TIMER_NUM) + hal_timer_t((HAL_TICKS_PER_US) * (MINIMUM_STEPPER_PULSE)); - #endif - + // Set the STEP pulse ON #if ENABLED(MIXING_EXTRUDER) MIXING_STEPPERS_LOOP(j) { // Step mixing steppers (proportionally) @@ -1828,15 +1831,18 @@ uint32_t Stepper::stepper_block_phase_isr() { E_STEP_WRITE(active_extruder, !INVERT_E_STEP_PIN); #endif + // Enforce a minimum duration for STEP pulse ON #if MINIMUM_STEPPER_PULSE // Just wait for the requested pulse duration while (HAL_timer_get_count(PULSE_TIMER_NUM) < pulse_end) { /* nada */ } - // Add to the value, the value needed for the pulse end and ensuring the maximum driver rate is enforced - pulse_end += hal_timer_t(MIN_STEPPER_PULSE_CYCLES) - hal_timer_t((HAL_TICKS_PER_US) * (MINIMUM_STEPPER_PULSE)); #endif + // Add the delay needed to ensure the maximum driver rate is enforced + if (signed(added_step_ticks) > 0) pulse_end += hal_timer_t(added_step_ticks); + LA_steps < 0 ? ++LA_steps : --LA_steps; + // Set the STEP pulse OFF #if ENABLED(MIXING_EXTRUDER) MIXING_STEPPERS_LOOP(j) { if (delta_error_m[j] >= 0) { @@ -1848,12 +1854,15 @@ uint32_t Stepper::stepper_block_phase_isr() { E_STEP_WRITE(active_extruder, INVERT_E_STEP_PIN); #endif - #if MINIMUM_STEPPER_PULSE - // For minimum pulse time wait before looping - // Just wait for the requested pulse duration - if (LA_steps) while (HAL_timer_get_count(PULSE_TIMER_NUM) < pulse_end) { /* nada */ } - #endif - + // For minimum pulse time wait before looping + // Just wait for the requested pulse duration + if (LA_steps) { + while (HAL_timer_get_count(PULSE_TIMER_NUM) < pulse_end) { /* nada */ } + #if MINIMUM_STEPPER_PULSE + // Add to the value, the time that the pulse must be active (to be used on the next loop) + pulse_end += hal_timer_t(MIN_PULSE_TICKS); + #endif + } } // LA_steps return interval; diff --git a/Marlin/src/module/stepper.h b/Marlin/src/module/stepper.h index 83fe45de48..eff7a5e3e1 100644 --- a/Marlin/src/module/stepper.h +++ b/Marlin/src/module/stepper.h @@ -43,19 +43,169 @@ #ifndef STEPPER_H #define STEPPER_H +#include "../inc/MarlinConfig.h" + +// Disable multiple steps per ISR +//#define DISABLE_MULTI_STEPPING + +// +// Estimate the amount of time the Stepper ISR will take to execute +// + +#ifndef MINIMUM_STEPPER_PULSE + #define MINIMUM_STEPPER_PULSE 0 +#endif + +#ifndef MAXIMUM_STEPPER_RATE + #if MINIMUM_STEPPER_PULSE + #define MAXIMUM_STEPPER_RATE (1000000UL / (2UL * (MINIMUM_STEPPER_PULSE))) + #else + #define MAXIMUM_STEPPER_RATE 500000UL + #endif +#endif + +#ifdef CPU_32_BIT + + // The base ISR takes 792 cycles + #define ISR_BASE_CYCLES 792UL + + // Linear advance base time is 64 cycles + #if ENABLED(LIN_ADVANCE) + #define ISR_LA_BASE_CYCLES 64UL + #else + #define ISR_LA_BASE_CYCLES 0UL + #endif + + // S curve interpolation adds 40 cycles + #if ENABLED(S_CURVE_ACCELERATION) + #define ISR_S_CURVE_CYCLES 40UL + #else + #define ISR_S_CURVE_CYCLES 0UL + #endif + + // Stepper Loop base cycles + #define ISR_LOOP_BASE_CYCLES 4UL + + // And each stepper takes 16 cycles + #define ISR_STEPPER_CYCLES 16UL + +#else + + // The base ISR takes 752 cycles + #define ISR_BASE_CYCLES 752UL + + // Linear advance base time is 32 cycles + #if ENABLED(LIN_ADVANCE) + #define ISR_LA_BASE_CYCLES 32UL + #else + #define ISR_LA_BASE_CYCLES 0UL + #endif + + // S curve interpolation adds 160 cycles + #if ENABLED(S_CURVE_ACCELERATION) + #define ISR_S_CURVE_CYCLES 160UL + #else + #define ISR_S_CURVE_CYCLES 0UL + #endif + + // Stepper Loop base cycles + #define ISR_LOOP_BASE_CYCLES 32UL + + // And each stepper takes 88 cycles + #define ISR_STEPPER_CYCLES 88UL + +#endif + +// Add time for each stepper +#ifdef HAS_X_STEP + #define ISR_X_STEPPER_CYCLES ISR_STEPPER_CYCLES +#else + #define ISR_X_STEPPER_CYCLES 0UL +#endif +#ifdef HAS_Y_STEP + #define ISR_Y_STEPPER_CYCLES ISR_STEPPER_CYCLES +#else + #define ISR_Y_STEPPER_CYCLES 0UL +#endif +#ifdef HAS_Z_STEP + #define ISR_Z_STEPPER_CYCLES ISR_STEPPER_CYCLES +#else + #define ISR_Z_STEPPER_CYCLES 0UL +#endif + +// E is always interpolated, even for mixing extruders +#define ISR_E_STEPPER_CYCLES ISR_STEPPER_CYCLES + +// If linear advance is disabled, then the loop also handles them +#if DISABLED(LIN_ADVANCE) && ENABLED(MIXING_EXTRUDER) + #define ISR_MIXING_STEPPER_CYCLES ((MIXING_STEPPERS) * (ISR_STEPPER_CYCLES)) +#else + #define ISR_MIXING_STEPPER_CYCLES 0UL +#endif + +// And the total minimum loop time, not including the base +#define MIN_ISR_LOOP_CYCLES (ISR_X_STEPPER_CYCLES + ISR_Y_STEPPER_CYCLES + ISR_Z_STEPPER_CYCLES + ISR_E_STEPPER_CYCLES + ISR_MIXING_STEPPER_CYCLES) + +// Calculate the minimum MPU cycles needed per pulse to enforce, limited to the max stepper rate +#define _MIN_STEPPER_PULSE_CYCLES(N) max((F_CPU) / (MAXIMUM_STEPPER_RATE), ((F_CPU) / 500000UL) * (N)) +#if MINIMUM_STEPPER_PULSE + #define MIN_STEPPER_PULSE_CYCLES _MIN_STEPPER_PULSE_CYCLES(MINIMUM_STEPPER_PULSE) +#else + #define MIN_STEPPER_PULSE_CYCLES _MIN_STEPPER_PULSE_CYCLES(1) +#endif + +#define MIN_PULSE_TICKS ((PULSE_TIMER_TICKS_PER_US) * (MINIMUM_STEPPER_PULSE)) +#define ADDED_STEP_TICKS ((MIN_STEPPER_PULSE_CYCLES) / (PULSE_TIMER_PRESCALE) - MIN_PULSE_TICKS) + +// But the user could be enforcing a minimum time, so the loop time is +#define ISR_LOOP_CYCLES (ISR_LOOP_BASE_CYCLES + max(MIN_STEPPER_PULSE_CYCLES, MIN_ISR_LOOP_CYCLES)) + +// If linear advance is enabled, then it is handled separately +#if ENABLED(LIN_ADVANCE) + + // Estimate the minimum LA loop time + #if ENABLED(MIXING_EXTRUDER) + #define MIN_ISR_LA_LOOP_CYCLES ((MIXING_STEPPERS) * (ISR_STEPPER_CYCLES)) + #else + #define MIN_ISR_LA_LOOP_CYCLES ISR_STEPPER_CYCLES + #endif + + // And the real loop time + #define ISR_LA_LOOP_CYCLES max(MIN_STEPPER_PULSE_CYCLES, MIN_ISR_LA_LOOP_CYCLES) + +#else + #define ISR_LA_LOOP_CYCLES 0UL +#endif + +// Now estimate the total ISR execution time in cycles given a step per ISR multiplier +#define ISR_EXECUTION_CYCLES(R) (((ISR_BASE_CYCLES + ISR_S_CURVE_CYCLES + (ISR_LOOP_CYCLES) * (R) + ISR_LA_BASE_CYCLES + ISR_LA_LOOP_CYCLES)) / (R)) + +// The maximum allowable stepping frequency when doing x128-x1 stepping (in Hz) +#define MAX_STEP_ISR_FREQUENCY_128X ((F_CPU) / ISR_EXECUTION_CYCLES(128)) +#define MAX_STEP_ISR_FREQUENCY_64X ((F_CPU) / ISR_EXECUTION_CYCLES(64)) +#define MAX_STEP_ISR_FREQUENCY_32X ((F_CPU) / ISR_EXECUTION_CYCLES(32)) +#define MAX_STEP_ISR_FREQUENCY_16X ((F_CPU) / ISR_EXECUTION_CYCLES(16)) +#define MAX_STEP_ISR_FREQUENCY_8X ((F_CPU) / ISR_EXECUTION_CYCLES(8)) +#define MAX_STEP_ISR_FREQUENCY_4X ((F_CPU) / ISR_EXECUTION_CYCLES(4)) +#define MAX_STEP_ISR_FREQUENCY_2X ((F_CPU) / ISR_EXECUTION_CYCLES(2)) +#define MAX_STEP_ISR_FREQUENCY_1X ((F_CPU) / ISR_EXECUTION_CYCLES(1)) + +// The minimum allowable frequency for step smoothing will be 1/10 of the maximum nominal frequency (in Hz) +#define MIN_STEP_ISR_FREQUENCY MAX_STEP_ISR_FREQUENCY_1X + +// +// Stepper class definition +// + #include "stepper_indirection.h" #ifdef __AVR__ #include "speed_lookuptable.h" #endif -#include "../inc/MarlinConfig.h" #include "../module/planner.h" #include "../core/language.h" -class Stepper; -extern Stepper stepper; - class Stepper { public: @@ -303,14 +453,14 @@ class Stepper { // The stepping frequency limits for each multistepping rate static const uint32_t limit[] PROGMEM = { - ( MAX_1X_STEP_ISR_FREQUENCY ), - ( MAX_2X_STEP_ISR_FREQUENCY >> 1), - ( MAX_4X_STEP_ISR_FREQUENCY >> 2), - ( MAX_8X_STEP_ISR_FREQUENCY >> 3), - ( MAX_16X_STEP_ISR_FREQUENCY >> 4), - ( MAX_32X_STEP_ISR_FREQUENCY >> 5), - ( MAX_64X_STEP_ISR_FREQUENCY >> 6), - (MAX_128X_STEP_ISR_FREQUENCY >> 7) + ( MAX_STEP_ISR_FREQUENCY_1X ), + ( MAX_STEP_ISR_FREQUENCY_2X >> 1), + ( MAX_STEP_ISR_FREQUENCY_4X >> 2), + ( MAX_STEP_ISR_FREQUENCY_8X >> 3), + ( MAX_STEP_ISR_FREQUENCY_16X >> 4), + ( MAX_STEP_ISR_FREQUENCY_32X >> 5), + ( MAX_STEP_ISR_FREQUENCY_64X >> 6), + (MAX_STEP_ISR_FREQUENCY_128X >> 7) }; // Select the proper multistepping @@ -321,7 +471,7 @@ class Stepper { ++idx; }; #else - NOMORE(step_rate, uint32_t(MAX_1X_STEP_ISR_FREQUENCY)); + NOMORE(step_rate, uint32_t(MAX_STEP_ISR_FREQUENCY_1X)); #endif *loops = multistep; @@ -367,4 +517,6 @@ class Stepper { }; +extern Stepper stepper; + #endif // STEPPER_H