Z_RAISE_PROBE_* => Z_PROBE_*_HEIGHT

9 years ago · 7e2bd9a233
26 changed files with 133 additions and 129 deletions
--- a/Marlin/Conditionals_post.h
+++ b/Marlin/Conditionals_post.h
@ -575,10 +575,10 @@
        #define XY_PROBE_SPEED 4000
      #endif
    #endif
-    #if Z_RAISE_BETWEEN_PROBINGS > Z_RAISE_PROBE_DEPLOY_STOW
-      #define _Z_RAISE_PROBE_DEPLOY_STOW Z_RAISE_BETWEEN_PROBINGS
+    #if Z_PROBE_TRAVEL_HEIGHT > Z_PROBE_DEPLOY_HEIGHT
+      #define _Z_PROBE_DEPLOY_HEIGHT Z_PROBE_TRAVEL_HEIGHT
    #else
-      #define _Z_RAISE_PROBE_DEPLOY_STOW Z_RAISE_PROBE_DEPLOY_STOW
+      #define _Z_PROBE_DEPLOY_HEIGHT Z_PROBE_DEPLOY_HEIGHT
    #endif
  #else
    #undef X_PROBE_OFFSET_FROM_EXTRUDER
@ -647,17 +647,17 @@
  #endif

  /**
-   * MIN_Z_HEIGHT_FOR_HOMING / Z_RAISE_BETWEEN_PROBINGS
+   * Z_HOMING_HEIGHT / Z_PROBE_TRAVEL_HEIGHT
   */
-  #ifndef MIN_Z_HEIGHT_FOR_HOMING
-    #ifndef Z_RAISE_BETWEEN_PROBINGS
-      #define MIN_Z_HEIGHT_FOR_HOMING 0
+  #ifndef Z_HOMING_HEIGHT
+    #ifndef Z_PROBE_TRAVEL_HEIGHT
+      #define Z_HOMING_HEIGHT 0
    #else
-      #define MIN_Z_HEIGHT_FOR_HOMING Z_RAISE_BETWEEN_PROBINGS
+      #define Z_HOMING_HEIGHT Z_PROBE_TRAVEL_HEIGHT
    #endif
  #endif
-  #ifndef Z_RAISE_BETWEEN_PROBINGS
-    #define Z_RAISE_BETWEEN_PROBING MIN_Z_HEIGHT_FOR_HOMING
+  #ifndef Z_PROBE_TRAVEL_HEIGHT
+    #define Z_PROBE_TRAVEL_HEIGHT Z_HOMING_HEIGHT
  #endif

 #endif // CONDITIONALS_POST_H
--- a/Marlin/Configuration.h
+++ b/Marlin/Configuration.h
@ -543,8 +543,8 @@
 //
 // Probe Raise options provide clearance for the probe to deploy, stow, and travel.
 //
-#define Z_RAISE_PROBE_DEPLOY_STOW 15 // Raise to make room for the probe to deploy / stow
-#define Z_RAISE_BETWEEN_PROBINGS 5  // Raise between probing points.
+#define Z_PROBE_DEPLOY_HEIGHT 15 // Raise to make room for the probe to deploy / stow
+#define Z_PROBE_TRAVEL_HEIGHT 5  // Raise between probing points.

 //
 // For M851 give a range for adjusting the Z probe offset
@ -589,8 +589,8 @@

 // @section homing

-//#define MIN_Z_HEIGHT_FOR_HOMING 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
-                                    // Be sure you have this distance over your Z_MAX_POS in case.
+//#define Z_HOMING_HEIGHT 4  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+                             // Be sure you have this distance over your Z_MAX_POS in case.

 // ENDSTOP SETTINGS:
 // Sets direction of endstops when homing; 1=MAX, -1=MIN
--- a/Marlin/Marlin_main.cpp
+++ b/Marlin/Marlin_main.cpp
@ -2050,7 +2050,7 @@ static void clean_up_after_endstop_or_probe_move() {
    if (endstops.z_probe_enabled == deploy) return false;

    // Make room for probe
-    do_probe_raise(_Z_RAISE_PROBE_DEPLOY_STOW);
+    do_probe_raise(_Z_PROBE_DEPLOY_HEIGHT);

    #if ENABLED(Z_PROBE_SLED)
      if (axis_unhomed_error(true, false, false)) { stop(); return true; }
@ -2159,7 +2159,7 @@ static void clean_up_after_endstop_or_probe_move() {
    float old_feedrate_mm_m = feedrate_mm_m;

    // Ensure a minimum height before moving the probe
-    do_probe_raise(Z_RAISE_BETWEEN_PROBINGS);
+    do_probe_raise(Z_PROBE_TRAVEL_HEIGHT);

    // Move to the XY where we shall probe
    #if ENABLED(DEBUG_LEVELING_FEATURE)
@ -2189,7 +2189,7 @@ static void clean_up_after_endstop_or_probe_move() {
      #if ENABLED(DEBUG_LEVELING_FEATURE)
        if (DEBUGGING(LEVELING)) SERIAL_ECHOLNPGM("> do_probe_raise");
      #endif
-      do_probe_raise(Z_RAISE_BETWEEN_PROBINGS);
+      do_probe_raise(Z_PROBE_TRAVEL_HEIGHT);
    }

    if (verbose_level > 2) {
@ -2967,7 +2967,7 @@ inline void gcode_G28() {

      if (home_all_axis || homeX || homeY) {
        // Raise Z before homing any other axes and z is not already high enough (never lower z)
-        destination[Z_AXIS] = LOGICAL_Z_POSITION(MIN_Z_HEIGHT_FOR_HOMING);
+        destination[Z_AXIS] = LOGICAL_Z_POSITION(Z_HOMING_HEIGHT);
        if (destination[Z_AXIS] > current_position[Z_AXIS]) {

          #if ENABLED(DEBUG_LEVELING_FEATURE)
@ -3048,7 +3048,7 @@ inline void gcode_G28() {
          if (home_all_axis) {

            /**
-             * At this point we already have Z at MIN_Z_HEIGHT_FOR_HOMING height
+             * At this point we already have Z at Z_HOMING_HEIGHT height
             * No need to move Z any more as this height should already be safe
             * enough to reach Z_SAFE_HOMING XY positions.
             * Just make sure the planner is in sync.
@ -3212,10 +3212,10 @@ inline void gcode_G28() {
    feedrate_mm_m = homing_feedrate_mm_m[X_AXIS];

    current_position[Z_AXIS] = MESH_HOME_SEARCH_Z
-      #if Z_RAISE_BETWEEN_PROBINGS > MIN_Z_HEIGHT_FOR_HOMING
-        + Z_RAISE_BETWEEN_PROBINGS
-      #elif MIN_Z_HEIGHT_FOR_HOMING > 0
-        + MIN_Z_HEIGHT_FOR_HOMING
+      #if Z_PROBE_TRAVEL_HEIGHT > Z_HOMING_HEIGHT
+        + Z_PROBE_TRAVEL_HEIGHT
+      #elif Z_HOMING_HEIGHT > 0
+        + Z_HOMING_HEIGHT
      #endif
    ;
    line_to_current_position();
@ -3224,7 +3224,7 @@ inline void gcode_G28() {
    current_position[Y_AXIS] = LOGICAL_Y_POSITION(y);
    line_to_current_position();

-    #if Z_RAISE_BETWEEN_PROBINGS > 0 || MIN_Z_HEIGHT_FOR_HOMING > 0
+    #if Z_PROBE_TRAVEL_HEIGHT > 0 || Z_HOMING_HEIGHT > 0
      current_position[Z_AXIS] = LOGICAL_Z_POSITION(MESH_HOME_SEARCH_Z);
      line_to_current_position();
    #endif
@ -3320,10 +3320,10 @@ inline void gcode_G28() {
        else {
          // One last "return to the bed" (as originally coded) at completion
          current_position[Z_AXIS] = MESH_HOME_SEARCH_Z
-            #if Z_RAISE_BETWEEN_PROBINGS > MIN_Z_HEIGHT_FOR_HOMING
-              + Z_RAISE_BETWEEN_PROBINGS
-            #elif MIN_Z_HEIGHT_FOR_HOMING > 0
-              + MIN_Z_HEIGHT_FOR_HOMING
+            #if Z_PROBE_TRAVEL_HEIGHT > Z_HOMING_HEIGHT
+              + Z_PROBE_TRAVEL_HEIGHT
+            #elif Z_HOMING_HEIGHT > 0
+              + Z_HOMING_HEIGHT
            #endif
          ;
          line_to_current_position();
@ -3657,7 +3657,7 @@ inline void gcode_G28() {

    #endif // !AUTO_BED_LEVELING_GRID

-    // Raise to _Z_RAISE_PROBE_DEPLOY_STOW. Stow the probe.
+    // Raise to _Z_PROBE_DEPLOY_HEIGHT. Stow the probe.
    if (STOW_PROBE()) return;

    // Restore state after probing
--- a/Marlin/SanityCheck.h
+++ b/Marlin/SanityCheck.h
@ -334,16 +334,14 @@
  /**
   * Make sure Z raise values are set
   */
-  #if defined(Z_RAISE_BEFORE_PROBING) || defined(Z_RAISE_AFTER_PROBING)
-    #error "Z_RAISE_(BEFORE|AFTER)_PROBING are deprecated. Use Z_RAISE_PROBE_DEPLOY_STOW instead."
-  #elif !defined(Z_RAISE_PROBE_DEPLOY_STOW)
-    #error "You must set Z_RAISE_PROBE_DEPLOY_STOW in your configuration."
-  #elif !defined(Z_RAISE_BETWEEN_PROBINGS)
-    #error "You must set Z_RAISE_BETWEEN_PROBINGS in your configuration."
-  #elif Z_RAISE_PROBE_DEPLOY_STOW < 0
-    #error "Probes need Z_RAISE_PROBE_DEPLOY_STOW >= 0."
-  #elif Z_RAISE_BETWEEN_PROBINGS < 0
-    #error "Probes need Z_RAISE_BETWEEN_PROBINGS >= 0."
+  #if !defined(Z_PROBE_DEPLOY_HEIGHT)
+    #error "You must set Z_PROBE_DEPLOY_HEIGHT in your configuration."
+  #elif !defined(Z_PROBE_TRAVEL_HEIGHT)
+    #error "You must set Z_PROBE_TRAVEL_HEIGHT in your configuration."
+  #elif Z_PROBE_DEPLOY_HEIGHT < 0
+    #error "Probes need Z_PROBE_DEPLOY_HEIGHT >= 0."
+  #elif Z_PROBE_TRAVEL_HEIGHT < 0
+    #error "Probes need Z_PROBE_TRAVEL_HEIGHT >= 0."
  #endif

 #else
@ -681,8 +679,6 @@
  #error "SDSLOW deprecated. Set SPI_SPEED to SPI_HALF_SPEED instead."
 #elif defined(SDEXTRASLOW)
  #error "SDEXTRASLOW deprecated. Set SPI_SPEED to SPI_QUARTER_SPEED instead."
-#elif defined(Z_RAISE_BEFORE_HOMING)
-  #error "Z_RAISE_BEFORE_HOMING is deprecated. Use MIN_Z_HEIGHT_FOR_HOMING instead."
 #elif defined(FILAMENT_SENSOR)
  #error "FILAMENT_SENSOR is deprecated. Use FILAMENT_WIDTH_SENSOR instead."
 #elif defined(DISABLE_MAX_ENDSTOPS) || defined(DISABLE_MIN_ENDSTOPS)
@ -729,4 +725,12 @@
  #error "MANUAL_HOME_POSITIONS is deprecated. Set MANUAL_[XYZ]_HOME_POS as-needed instead."
 #elif defined(PID_ADD_EXTRUSION_RATE)
  #error "PID_ADD_EXTRUSION_RATE is now PID_EXTRUSION_SCALING and is DISABLED by default. Are you sure you want to use this option? Please update your configuration."
+#elif defined(Z_RAISE_BEFORE_HOMING)
+  #error "Z_RAISE_BEFORE_HOMING is now Z_HOMING_HEIGHT. Please update your configuration."
+#elif defined(MIN_Z_HEIGHT_FOR_HOMING)
+  #error "MIN_Z_HEIGHT_FOR_HOMING is now Z_HOMING_HEIGHT. Please update your configuration."
+#elif defined(Z_RAISE_BEFORE_PROBING) || defined(Z_RAISE_AFTER_PROBING)
+  #error "Z_RAISE_(BEFORE|AFTER)_PROBING are deprecated. Use Z_PROBE_DEPLOY_HEIGHT instead."
+#elif defined(Z_RAISE_PROBE_DEPLOY_STOW) || defined(Z_RAISE_BETWEEN_PROBINGS)
+  #error "Z_RAISE_PROBE_DEPLOY_STOW and Z_RAISE_BETWEEN_PROBINGS are now Z_PROBE_DEPLOY_HEIGHT and Z_PROBE_TRAVEL_HEIGHT Please update your configuration."
 #endif
--- a/Marlin/example_configurations/Cartesio/Configuration.h
+++ b/Marlin/example_configurations/Cartesio/Configuration.h
@ -543,8 +543,8 @@
 //
 // Probe Raise options provide clearance for the probe to deploy, stow, and travel.
 //
-#define Z_RAISE_PROBE_DEPLOY_STOW 15 // Raise to make room for the probe to deploy / stow
-#define Z_RAISE_BETWEEN_PROBINGS 5  // Raise between probing points.
+#define Z_PROBE_DEPLOY_HEIGHT 15 // Raise to make room for the probe to deploy / stow
+#define Z_PROBE_TRAVEL_HEIGHT 5  // Raise between probing points.

 //
 // For M851 give a range for adjusting the Z probe offset
@ -589,8 +589,8 @@

 // @section homing

-//#define MIN_Z_HEIGHT_FOR_HOMING 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
-                                    // Be sure you have this distance over your Z_MAX_POS in case.
+//#define Z_HOMING_HEIGHT 4  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+                             // Be sure you have this distance over your Z_MAX_POS in case.

 // ENDSTOP SETTINGS:
 // Sets direction of endstops when homing; 1=MAX, -1=MIN
--- a/Marlin/example_configurations/Felix/Configuration.h
+++ b/Marlin/example_configurations/Felix/Configuration.h
@ -525,8 +525,8 @@
 //
 // Probe Raise options provide clearance for the probe to deploy, stow, and travel.
 //
-#define Z_RAISE_PROBE_DEPLOY_STOW 15 // Raise to make room for the probe to deploy / stow
-#define Z_RAISE_BETWEEN_PROBINGS 5  // Raise between probing points.
+#define Z_PROBE_DEPLOY_HEIGHT 15 // Raise to make room for the probe to deploy / stow
+#define Z_PROBE_TRAVEL_HEIGHT 5  // Raise between probing points.

 //
 // For M851 give a range for adjusting the Z probe offset
@ -571,8 +571,8 @@

 // @section homing

-//#define MIN_Z_HEIGHT_FOR_HOMING 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
-                                    // Be sure you have this distance over your Z_MAX_POS in case.
+//#define Z_HOMING_HEIGHT 4  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+                             // Be sure you have this distance over your Z_MAX_POS in case.

 // ENDSTOP SETTINGS:
 // Sets direction of endstops when homing; 1=MAX, -1=MIN
--- a/Marlin/example_configurations/Felix/DUAL/Configuration.h
+++ b/Marlin/example_configurations/Felix/DUAL/Configuration.h
@ -523,8 +523,8 @@
 //
 // Probe Raise options provide clearance for the probe to deploy, stow, and travel.
 //
-#define Z_RAISE_PROBE_DEPLOY_STOW 15 // Raise to make room for the probe to deploy / stow
-#define Z_RAISE_BETWEEN_PROBINGS 5  // Raise between probing points.
+#define Z_PROBE_DEPLOY_HEIGHT 15 // Raise to make room for the probe to deploy / stow
+#define Z_PROBE_TRAVEL_HEIGHT 5  // Raise between probing points.

 //
 // For M851 give a range for adjusting the Z probe offset
@ -569,8 +569,8 @@

 // @section homing

-//#define MIN_Z_HEIGHT_FOR_HOMING 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
-                                    // Be sure you have this distance over your Z_MAX_POS in case.
+//#define Z_HOMING_HEIGHT 4  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+                             // Be sure you have this distance over your Z_MAX_POS in case.

 // ENDSTOP SETTINGS:
 // Sets direction of endstops when homing; 1=MAX, -1=MIN
--- a/Marlin/example_configurations/Hephestos/Configuration.h
+++ b/Marlin/example_configurations/Hephestos/Configuration.h
@ -535,8 +535,8 @@
 //
 // Probe Raise options provide clearance for the probe to deploy, stow, and travel.
 //
-#define Z_RAISE_PROBE_DEPLOY_STOW 15 // Raise to make room for the probe to deploy / stow
-#define Z_RAISE_BETWEEN_PROBINGS 5  // Raise between probing points.
+#define Z_PROBE_DEPLOY_HEIGHT 15 // Raise to make room for the probe to deploy / stow
+#define Z_PROBE_TRAVEL_HEIGHT 5  // Raise between probing points.

 //
 // For M851 give a range for adjusting the Z probe offset
@ -581,8 +581,8 @@

 // @section homing

-//#define MIN_Z_HEIGHT_FOR_HOMING 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
-                                    // Be sure you have this distance over your Z_MAX_POS in case.
+//#define Z_HOMING_HEIGHT 4  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+                             // Be sure you have this distance over your Z_MAX_POS in case.

 // ENDSTOP SETTINGS:
 // Sets direction of endstops when homing; 1=MAX, -1=MIN
--- a/Marlin/example_configurations/Hephestos_2/Configuration.h
+++ b/Marlin/example_configurations/Hephestos_2/Configuration.h
@ -537,8 +537,8 @@
 //
 // Probe Raise options provide clearance for the probe to deploy, stow, and travel.
 //
-#define Z_RAISE_PROBE_DEPLOY_STOW  5 // Raise to make room for the probe to deploy / stow
-#define Z_RAISE_BETWEEN_PROBINGS 2  // Raise between probing points.
+#define Z_PROBE_DEPLOY_HEIGHT  5 // Raise to make room for the probe to deploy / stow
+#define Z_PROBE_TRAVEL_HEIGHT 2  // Raise between probing points.

 //
 // For M851 give a range for adjusting the Z probe offset
@ -583,8 +583,8 @@

 // @section homing

-#define MIN_Z_HEIGHT_FOR_HOMING 5   // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
-                                    // Be sure you have this distance over your Z_MAX_POS in case.
+#define Z_HOMING_HEIGHT 5    // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+                             // Be sure you have this distance over your Z_MAX_POS in case.

 // ENDSTOP SETTINGS:
 // Sets direction of endstops when homing; 1=MAX, -1=MIN
--- a/Marlin/example_configurations/K8200/Configuration.h
+++ b/Marlin/example_configurations/K8200/Configuration.h
@ -560,8 +560,8 @@
 //
 // Probe Raise options provide clearance for the probe to deploy, stow, and travel.
 //
-#define Z_RAISE_PROBE_DEPLOY_STOW 15 // Raise to make room for the probe to deploy / stow
-#define Z_RAISE_BETWEEN_PROBINGS 5  // Raise between probing points.
+#define Z_PROBE_DEPLOY_HEIGHT 15 // Raise to make room for the probe to deploy / stow
+#define Z_PROBE_TRAVEL_HEIGHT 5  // Raise between probing points.

 //
 // For M851 give a range for adjusting the Z probe offset
@ -606,8 +606,8 @@

 // @section homing

-//#define MIN_Z_HEIGHT_FOR_HOMING 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
-                                    // Be sure you have this distance over your Z_MAX_POS in case.
+//#define Z_HOMING_HEIGHT 4  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+                             // Be sure you have this distance over your Z_MAX_POS in case.

 // ENDSTOP SETTINGS:
 // Sets direction of endstops when homing; 1=MAX, -1=MIN
--- a/Marlin/example_configurations/K8400/Configuration.h
+++ b/Marlin/example_configurations/K8400/Configuration.h
@ -543,8 +543,8 @@
 //
 // Probe Raise options provide clearance for the probe to deploy, stow, and travel.
 //
-#define Z_RAISE_PROBE_DEPLOY_STOW 15 // Raise to make room for the probe to deploy / stow
-#define Z_RAISE_BETWEEN_PROBINGS 5  // Raise between probing points.
+#define Z_PROBE_DEPLOY_HEIGHT 15 // Raise to make room for the probe to deploy / stow
+#define Z_PROBE_TRAVEL_HEIGHT 5  // Raise between probing points.

 //
 // For M851 give a range for adjusting the Z probe offset
@ -589,8 +589,8 @@

 // @section homing

-//#define MIN_Z_HEIGHT_FOR_HOMING 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
-                                    // Be sure you have this distance over your Z_MAX_POS in case.
+//#define Z_HOMING_HEIGHT 4  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+                             // Be sure you have this distance over your Z_MAX_POS in case.

 // ENDSTOP SETTINGS:
 // Sets direction of endstops when homing; 1=MAX, -1=MIN
--- a/Marlin/example_configurations/K8400/Dual-head/Configuration.h
+++ b/Marlin/example_configurations/K8400/Dual-head/Configuration.h
@ -543,8 +543,8 @@
 //
 // Probe Raise options provide clearance for the probe to deploy, stow, and travel.
 //
-#define Z_RAISE_PROBE_DEPLOY_STOW 15 // Raise to make room for the probe to deploy / stow
-#define Z_RAISE_BETWEEN_PROBINGS 5  // Raise between probing points.
+#define Z_PROBE_DEPLOY_HEIGHT 15 // Raise to make room for the probe to deploy / stow
+#define Z_PROBE_TRAVEL_HEIGHT 5  // Raise between probing points.

 //
 // For M851 give a range for adjusting the Z probe offset
@ -589,8 +589,8 @@

 // @section homing

-//#define MIN_Z_HEIGHT_FOR_HOMING 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
-                                    // Be sure you have this distance over your Z_MAX_POS in case.
+//#define Z_HOMING_HEIGHT 4  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+                             // Be sure you have this distance over your Z_MAX_POS in case.

 // ENDSTOP SETTINGS:
 // Sets direction of endstops when homing; 1=MAX, -1=MIN
--- a/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h
+++ b/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h
@ -543,8 +543,8 @@
 //
 // Probe Raise options provide clearance for the probe to deploy, stow, and travel.
 //
-#define Z_RAISE_PROBE_DEPLOY_STOW 15 // Raise to make room for the probe to deploy / stow
-#define Z_RAISE_BETWEEN_PROBINGS 5  // Raise between probing points.
+#define Z_PROBE_DEPLOY_HEIGHT 15 // Raise to make room for the probe to deploy / stow
+#define Z_PROBE_TRAVEL_HEIGHT 5  // Raise between probing points.

 //
 // For M851 give a range for adjusting the Z probe offset
@ -589,8 +589,8 @@

 // @section homing

-//#define MIN_Z_HEIGHT_FOR_HOMING 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
-                                    // Be sure you have this distance over your Z_MAX_POS in case.
+//#define Z_HOMING_HEIGHT 4  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+                             // Be sure you have this distance over your Z_MAX_POS in case.

 // ENDSTOP SETTINGS:
 // Sets direction of endstops when homing; 1=MAX, -1=MIN
--- a/Marlin/example_configurations/RigidBot/Configuration.h
+++ b/Marlin/example_configurations/RigidBot/Configuration.h
@ -540,8 +540,8 @@
 //
 // Probe Raise options provide clearance for the probe to deploy, stow, and travel.
 //
-#define Z_RAISE_PROBE_DEPLOY_STOW 15 // Raise to make room for the probe to deploy / stow
-#define Z_RAISE_BETWEEN_PROBINGS 5  // Raise between probing points.
+#define Z_PROBE_DEPLOY_HEIGHT 15 // Raise to make room for the probe to deploy / stow
+#define Z_PROBE_TRAVEL_HEIGHT 5  // Raise between probing points.

 //
 // For M851 give a range for adjusting the Z probe offset
@ -586,8 +586,8 @@

 // @section homing

-//#define MIN_Z_HEIGHT_FOR_HOMING 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
-                                    // Be sure you have this distance over your Z_MAX_POS in case.
+//#define Z_HOMING_HEIGHT 4  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+                             // Be sure you have this distance over your Z_MAX_POS in case.

 // ENDSTOP SETTINGS:
 // Sets direction of endstops when homing; 1=MAX, -1=MIN
--- a/Marlin/example_configurations/SCARA/Configuration.h
+++ b/Marlin/example_configurations/SCARA/Configuration.h
@ -551,8 +551,8 @@
 //
 // Probe Raise options provide clearance for the probe to deploy, stow, and travel.
 //
-#define Z_RAISE_PROBE_DEPLOY_STOW 15 // Raise to make room for the probe to deploy / stow
-#define Z_RAISE_BETWEEN_PROBINGS 5  // Raise between probing points.
+#define Z_PROBE_DEPLOY_HEIGHT 15 // Raise to make room for the probe to deploy / stow
+#define Z_PROBE_TRAVEL_HEIGHT 5  // Raise between probing points.

 //
 // For M851 give a range for adjusting the Z probe offset
@ -597,8 +597,8 @@

 // @section homing

-//#define MIN_Z_HEIGHT_FOR_HOMING 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
-                                    // Be sure you have this distance over your Z_MAX_POS in case.
+//#define Z_HOMING_HEIGHT 4  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+                             // Be sure you have this distance over your Z_MAX_POS in case.

 // ENDSTOP SETTINGS:
 // Sets direction of endstops when homing; 1=MAX, -1=MIN
--- a/Marlin/example_configurations/TAZ4/Configuration.h
+++ b/Marlin/example_configurations/TAZ4/Configuration.h
@ -564,8 +564,8 @@
 //
 // Probe Raise options provide clearance for the probe to deploy, stow, and travel.
 //
-#define Z_RAISE_PROBE_DEPLOY_STOW 15 // Raise to make room for the probe to deploy / stow
-#define Z_RAISE_BETWEEN_PROBINGS 5  // Raise between probing points.
+#define Z_PROBE_DEPLOY_HEIGHT 15 // Raise to make room for the probe to deploy / stow
+#define Z_PROBE_TRAVEL_HEIGHT 5  // Raise between probing points.

 //
 // For M851 give a range for adjusting the Z probe offset
@ -610,8 +610,8 @@

 // @section homing

-//#define MIN_Z_HEIGHT_FOR_HOMING 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
-                                    // Be sure you have this distance over your Z_MAX_POS in case.
+//#define Z_HOMING_HEIGHT 4  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+                             // Be sure you have this distance over your Z_MAX_POS in case.

 // ENDSTOP SETTINGS:
 // Sets direction of endstops when homing; 1=MAX, -1=MIN
--- a/Marlin/example_configurations/WITBOX/Configuration.h
+++ b/Marlin/example_configurations/WITBOX/Configuration.h
@ -535,8 +535,8 @@
 //
 // Probe Raise options provide clearance for the probe to deploy, stow, and travel.
 //
-#define Z_RAISE_PROBE_DEPLOY_STOW 15 // Raise to make room for the probe to deploy / stow
-#define Z_RAISE_BETWEEN_PROBINGS 5  // Raise between probing points.
+#define Z_PROBE_DEPLOY_HEIGHT 15 // Raise to make room for the probe to deploy / stow
+#define Z_PROBE_TRAVEL_HEIGHT 5  // Raise between probing points.

 //
 // For M851 give a range for adjusting the Z probe offset
@ -581,8 +581,8 @@

 // @section homing

-//#define MIN_Z_HEIGHT_FOR_HOMING 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
-                                    // Be sure you have this distance over your Z_MAX_POS in case.
+//#define Z_HOMING_HEIGHT 4  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+                             // Be sure you have this distance over your Z_MAX_POS in case.

 // ENDSTOP SETTINGS:
 // Sets direction of endstops when homing; 1=MAX, -1=MIN
--- a/Marlin/example_configurations/adafruit/ST7565/Configuration.h
+++ b/Marlin/example_configurations/adafruit/ST7565/Configuration.h
@ -543,8 +543,8 @@
 //
 // Probe Raise options provide clearance for the probe to deploy, stow, and travel.
 //
-#define Z_RAISE_PROBE_DEPLOY_STOW 15 // Raise to make room for the probe to deploy / stow
-#define Z_RAISE_BETWEEN_PROBINGS 5  // Raise between probing points.
+#define Z_PROBE_DEPLOY_HEIGHT 15 // Raise to make room for the probe to deploy / stow
+#define Z_PROBE_TRAVEL_HEIGHT 5  // Raise between probing points.

 //
 // For M851 give a range for adjusting the Z probe offset
@ -589,8 +589,8 @@

 // @section homing

-//#define MIN_Z_HEIGHT_FOR_HOMING 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
-                                    // Be sure you have this distance over your Z_MAX_POS in case.
+//#define Z_HOMING_HEIGHT 4  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+                             // Be sure you have this distance over your Z_MAX_POS in case.

 // ENDSTOP SETTINGS:
 // Sets direction of endstops when homing; 1=MAX, -1=MIN
--- a/Marlin/example_configurations/delta/biv2.5/Configuration.h
+++ b/Marlin/example_configurations/delta/biv2.5/Configuration.h
@ -632,8 +632,8 @@
 //
 // Probe Raise options provide clearance for the probe to deploy, stow, and travel.
 //
-#define Z_RAISE_PROBE_DEPLOY_STOW 50 // Raise to make room for the probe to deploy / stow
-#define Z_RAISE_BETWEEN_PROBINGS 5  // Raise between probing points.
+#define Z_PROBE_DEPLOY_HEIGHT 50 // Raise to make room for the probe to deploy / stow
+#define Z_PROBE_TRAVEL_HEIGHT 5  // Raise between probing points.

 //
 // For M851 give a range for adjusting the Z probe offset
@ -678,8 +678,8 @@

 // @section homing

-//#define MIN_Z_HEIGHT_FOR_HOMING 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
-                                    // Be sure you have this distance over your Z_MAX_POS in case.
+//#define Z_HOMING_HEIGHT 4  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+                             // Be sure you have this distance over your Z_MAX_POS in case.

 // ENDSTOP SETTINGS:
 // Sets direction of endstops when homing; 1=MAX, -1=MIN
--- a/Marlin/example_configurations/delta/generic/Configuration.h
+++ b/Marlin/example_configurations/delta/generic/Configuration.h
@ -626,8 +626,8 @@
 //
 // Probe Raise options provide clearance for the probe to deploy, stow, and travel.
 //
-#define Z_RAISE_PROBE_DEPLOY_STOW 15 // Raise to make room for the probe to deploy / stow
-#define Z_RAISE_BETWEEN_PROBINGS 5  // Raise between probing points.
+#define Z_PROBE_DEPLOY_HEIGHT 15 // Raise to make room for the probe to deploy / stow
+#define Z_PROBE_TRAVEL_HEIGHT 5  // Raise between probing points.

 //
 // For M851 give a range for adjusting the Z probe offset
@ -672,8 +672,8 @@

 // @section homing

-//#define MIN_Z_HEIGHT_FOR_HOMING 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
-                                    // Be sure you have this distance over your Z_MAX_POS in case.
+//#define Z_HOMING_HEIGHT 4  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+                             // Be sure you have this distance over your Z_MAX_POS in case.

 // ENDSTOP SETTINGS:
 // Sets direction of endstops when homing; 1=MAX, -1=MIN
--- a/Marlin/example_configurations/delta/kossel_mini/Configuration.h
+++ b/Marlin/example_configurations/delta/kossel_mini/Configuration.h
@ -629,8 +629,8 @@
 //
 // Probe Raise options provide clearance for the probe to deploy, stow, and travel.
 //
-#define Z_RAISE_PROBE_DEPLOY_STOW 50 // Raise to make room for the probe to deploy / stow
-#define Z_RAISE_BETWEEN_PROBINGS 5  // Raise between probing points.
+#define Z_PROBE_DEPLOY_HEIGHT 50 // Raise to make room for the probe to deploy / stow
+#define Z_PROBE_TRAVEL_HEIGHT 5  // Raise between probing points.

 //
 // For M851 give a range for adjusting the Z probe offset
@ -675,8 +675,8 @@

 // @section homing

-//#define MIN_Z_HEIGHT_FOR_HOMING 15// (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
-                                    // Be sure you have this distance over your Z_MAX_POS in case.
+//#define Z_HOMING_HEIGHT 15 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+                             // Be sure you have this distance over your Z_MAX_POS in case.

 // ENDSTOP SETTINGS:
 // Sets direction of endstops when homing; 1=MAX, -1=MIN
--- a/Marlin/example_configurations/delta/kossel_pro/Configuration.h
+++ b/Marlin/example_configurations/delta/kossel_pro/Configuration.h
@ -623,8 +623,8 @@
 //
 // Probe Raise options provide clearance for the probe to deploy, stow, and travel.
 //
-#define Z_RAISE_PROBE_DEPLOY_STOW 100 // Raise to make room for the probe to deploy / stow
-#define Z_RAISE_BETWEEN_PROBINGS 5  // Raise between probing points.
+#define Z_PROBE_DEPLOY_HEIGHT 100 // Raise to make room for the probe to deploy / stow
+#define Z_PROBE_TRAVEL_HEIGHT 5  // Raise between probing points.

 //
 // For M851 give a range for adjusting the Z probe offset
@ -669,8 +669,8 @@

 // @section homing

-//#define MIN_Z_HEIGHT_FOR_HOMING 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
-                                    // Be sure you have this distance over your Z_MAX_POS in case.
+//#define Z_HOMING_HEIGHT 4  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+                             // Be sure you have this distance over your Z_MAX_POS in case.

 // ENDSTOP SETTINGS:
 // Sets direction of endstops when homing; 1=MAX, -1=MIN
--- a/Marlin/example_configurations/delta/kossel_xl/Configuration.h
+++ b/Marlin/example_configurations/delta/kossel_xl/Configuration.h
@ -624,8 +624,8 @@
 //
 // Probe Raise options provide clearance for the probe to deploy, stow, and travel.
 //
-#define Z_RAISE_PROBE_DEPLOY_STOW 20 // Raise to make room for the probe to deploy / stow
-#define Z_RAISE_BETWEEN_PROBINGS 10 // Raise between probing points.
+#define Z_PROBE_DEPLOY_HEIGHT 20 // Raise to make room for the probe to deploy / stow
+#define Z_PROBE_TRAVEL_HEIGHT 10 // Raise between probing points.

 //
 // For M851 give a range for adjusting the Z probe offset
@ -670,8 +670,8 @@

 // @section homing

-//#define MIN_Z_HEIGHT_FOR_HOMING 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
-                                    // Be sure you have this distance over your Z_MAX_POS in case.
+//#define Z_HOMING_HEIGHT 4  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+                             // Be sure you have this distance over your Z_MAX_POS in case.

 // ENDSTOP SETTINGS:
 // Sets direction of endstops when homing; 1=MAX, -1=MIN
--- a/Marlin/example_configurations/makibox/Configuration.h
+++ b/Marlin/example_configurations/makibox/Configuration.h
@ -546,8 +546,8 @@
 //
 // Probe Raise options provide clearance for the probe to deploy, stow, and travel.
 //
-#define Z_RAISE_PROBE_DEPLOY_STOW 15 // Raise to make room for the probe to deploy / stow
-#define Z_RAISE_BETWEEN_PROBINGS 5  // Raise between probing points.
+#define Z_PROBE_DEPLOY_HEIGHT 15 // Raise to make room for the probe to deploy / stow
+#define Z_PROBE_TRAVEL_HEIGHT 5  // Raise between probing points.

 //
 // For M851 give a range for adjusting the Z probe offset
@ -592,8 +592,8 @@

 // @section homing

-//#define MIN_Z_HEIGHT_FOR_HOMING 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
-                                    // Be sure you have this distance over your Z_MAX_POS in case.
+//#define Z_HOMING_HEIGHT 4  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+                             // Be sure you have this distance over your Z_MAX_POS in case.

 // ENDSTOP SETTINGS:
 // Sets direction of endstops when homing; 1=MAX, -1=MIN
--- a/Marlin/example_configurations/tvrrug/Round2/Configuration.h
+++ b/Marlin/example_configurations/tvrrug/Round2/Configuration.h
@ -533,8 +533,8 @@
 //
 // Probe Raise options provide clearance for the probe to deploy, stow, and travel.
 //
-#define Z_RAISE_PROBE_DEPLOY_STOW 15 // Raise to make room for the probe to deploy / stow
-#define Z_RAISE_BETWEEN_PROBINGS 5  // Raise between probing points.
+#define Z_PROBE_DEPLOY_HEIGHT 15 // Raise to make room for the probe to deploy / stow
+#define Z_PROBE_TRAVEL_HEIGHT 5  // Raise between probing points.

 //
 // For M851 give a range for adjusting the Z probe offset
@ -579,8 +579,8 @@

 // @section homing

-//#define MIN_Z_HEIGHT_FOR_HOMING 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
-                                    // Be sure you have this distance over your Z_MAX_POS in case.
+//#define Z_HOMING_HEIGHT 4  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+                             // Be sure you have this distance over your Z_MAX_POS in case.

 // ENDSTOP SETTINGS:
 // Sets direction of endstops when homing; 1=MAX, -1=MIN
--- a/Marlin/ultralcd.cpp
+++ b/Marlin/ultralcd.cpp
@ -985,16 +985,16 @@ void kill_screen(const char* lcd_msg) {
    static uint8_t _lcd_level_bed_position;

    // Utility to go to the next mesh point
-    // A raise is added between points if MIN_Z_HEIGHT_FOR_HOMING is in use
+    // A raise is added between points if Z_HOMING_HEIGHT is in use
    // Note: During Manual Bed Leveling the homed Z position is MESH_HOME_SEARCH_Z
    // Z position will be restored with the final action, a G28
    inline void _mbl_goto_xy(float x, float y) {
-      current_position[Z_AXIS] = MESH_HOME_SEARCH_Z + MIN_Z_HEIGHT_FOR_HOMING;
+      current_position[Z_AXIS] = MESH_HOME_SEARCH_Z + Z_HOMING_HEIGHT;
      line_to_current(Z_AXIS);
      current_position[X_AXIS] = x + home_offset[X_AXIS];
      current_position[Y_AXIS] = y + home_offset[Y_AXIS];
      line_to_current(manual_feedrate_mm_m[X_AXIS] <= manual_feedrate_mm_m[Y_AXIS] ? X_AXIS : Y_AXIS);
-      #if MIN_Z_HEIGHT_FOR_HOMING > 0
+      #if Z_HOMING_HEIGHT > 0
        current_position[Z_AXIS] = MESH_HOME_SEARCH_Z; // How do condition and action match?
        line_to_current(Z_AXIS);
      #endif
@ -1045,7 +1045,7 @@ void kill_screen(const char* lcd_msg) {
          if (_lcd_level_bed_position == (MESH_NUM_X_POINTS) * (MESH_NUM_Y_POINTS)) {
            lcd_goto_screen(_lcd_level_bed_done, true);

-            current_position[Z_AXIS] = MESH_HOME_SEARCH_Z + MIN_Z_HEIGHT_FOR_HOMING;
+            current_position[Z_AXIS] = MESH_HOME_SEARCH_Z + Z_HOMING_HEIGHT;
            line_to_current(Z_AXIS);
            stepper.synchronize();