Browse Source

📌 Fix, extend Index Rev03 Mobo (#23851)

Co-authored-by: Scott Lahteine <thinkyhead@users.noreply.github.com>
FB4S_WIFI
GatCode 3 years ago
committed by Scott Lahteine
parent
commit
7dae720de5
  1. 4
      Marlin/src/inc/SanityCheck.h
  2. 96
      Marlin/src/pins/stm32f4/pins_INDEX_REV03.h

4
Marlin/src/inc/SanityCheck.h

@ -2183,9 +2183,9 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
* Test Sensor & Heater pin combos. * Test Sensor & Heater pin combos.
* Pins and Sensor IDs must be set for each heater * Pins and Sensor IDs must be set for each heater
*/ */
#if !ANY_PIN(TEMP_0, TEMP_0_CS) #if HAS_EXTRUDERS && !ANY_PIN(TEMP_0, TEMP_0_CS)
#error "TEMP_0_PIN or TEMP_0_CS_PIN not defined for this board." #error "TEMP_0_PIN or TEMP_0_CS_PIN not defined for this board."
#elif !HAS_HEATER_0 && EXTRUDERS #elif HAS_EXTRUDERS && !HAS_HEATER_0
#error "HEATER_0_PIN not defined for this board." #error "HEATER_0_PIN not defined for this board."
#elif TEMP_SENSOR_0_IS_MAX_TC && !PIN_EXISTS(TEMP_0_CS) #elif TEMP_SENSOR_0_IS_MAX_TC && !PIN_EXISTS(TEMP_0_CS)
#error "TEMP_SENSOR_0 MAX thermocouple requires TEMP_0_CS_PIN." #error "TEMP_SENSOR_0 MAX thermocouple requires TEMP_0_CS_PIN."

96
Marlin/src/pins/stm32f4/pins_INDEX_REV03.h

@ -60,12 +60,12 @@
// None of these require limit switches by default, so we leave these commented // None of these require limit switches by default, so we leave these commented
// here for your reference. // here for your reference.
// #define I_MIN_PIN PA8 //#define I_MIN_PIN PA8
// #define I_MAX_PIN PA8 //#define I_MAX_PIN PA8
// #define J_MIN_PIN PD13 //#define J_MIN_PIN PD13
// #define J_MAX_PIN PD13 //#define J_MAX_PIN PD13
// #define K_MIN_PIN PC9 //#define K_MIN_PIN PC9
// #define K_MAX_PIN PC9 //#define K_MAX_PIN PC9
// //
// Steppers // Steppers
@ -73,47 +73,81 @@
#define X_STEP_PIN PB15 #define X_STEP_PIN PB15
#define X_DIR_PIN PB14 #define X_DIR_PIN PB14
#define X_ENABLE_PIN PD9 #define X_ENABLE_PIN PD9
#define X_SERIAL_TX_PIN PD8
#define X_SERIAL_RX_PIN PD8
#define Y_STEP_PIN PE15 #define Y_STEP_PIN PE15
#define Y_DIR_PIN PE14 #define Y_DIR_PIN PE14
#define Y_ENABLE_PIN PB13 #define Y_ENABLE_PIN PB13
#define Y_SERIAL_TX_PIN PB12
#define Y_SERIAL_RX_PIN PB12
#define Z_STEP_PIN PE7 #define Z_STEP_PIN PE7
#define Z_DIR_PIN PB1 #define Z_DIR_PIN PB1
#define Z_ENABLE_PIN PE9 #define Z_ENABLE_PIN PE9
#define Z_SERIAL_TX_PIN PE8
#define Z_SERIAL_RX_PIN PE8
#define I_STEP_PIN PC4 #define I_STEP_PIN PC4
#define I_DIR_PIN PA4 #define I_DIR_PIN PA4
#define I_ENABLE_PIN PB0 #define I_ENABLE_PIN PB0
#define I_SERIAL_TX_PIN PC5
#define I_SERIAL_RX_PIN PC5
#define J_STEP_PIN PE11 #define J_STEP_PIN PE11
#define J_DIR_PIN PE10 #define J_DIR_PIN PE10
#define J_ENABLE_PIN PE13 #define J_ENABLE_PIN PE13
#define J_SERIAL_TX_PIN PE12
#define J_SERIAL_RX_PIN PE12
#define K_SERIAL_TX_PIN PA2
#define K_SERIAL_RX_PIN PA2
#define K_STEP_PIN PD6 #define K_STEP_PIN PD6
#define K_DIR_PIN PD7 #define K_DIR_PIN PD7
#define K_ENABLE_PIN PA3 #define K_ENABLE_PIN PA3
// Reduce baud rate to improve software serial reliability #if HAS_TMC_SPI
#define TMC_BAUD_RATE 19200 /**
* Make sure to configure the jumpers on the back side of the Mobo according to
* this diagram: https://github.com/MarlinFirmware/Marlin/pull/23851
*/
#error "SPI drivers require a custom jumper configuration, see comment above! Comment out this line to continue."
#if AXIS_HAS_SPI(X)
#define X_CS_PIN PD8
#endif
#if AXIS_HAS_SPI(Y)
#define Y_CS_PIN PB12
#endif
#if AXIS_HAS_SPI(Z)
#define Z_CS_PIN PE8
#endif
#if AXIS_HAS_SPI(I)
#define I_CS_PIN PC5
#endif
#if AXIS_HAS_SPI(J)
#define J_CS_PIN PE12
#endif
#if AXIS_HAS_SPI(K)
#define K_CS_PIN PA2
#endif
#elif HAS_TMC_UART
#define X_SERIAL_TX_PIN PD8
#define X_SERIAL_RX_PIN X_SERIAL_TX_PIN
#define Y_SERIAL_TX_PIN PB12
#define Y_SERIAL_RX_PIN Y_SERIAL_TX_PIN
#define Z_SERIAL_TX_PIN PE8
#define Z_SERIAL_RX_PIN Z_SERIAL_TX_PIN
#define I_SERIAL_TX_PIN PC5
#define I_SERIAL_RX_PIN I_SERIAL_TX_PIN
#define J_SERIAL_TX_PIN PE12
#define J_SERIAL_RX_PIN J_SERIAL_TX_PIN
#define K_SERIAL_TX_PIN PA2
#define K_SERIAL_RX_PIN K_SERIAL_TX_PIN
// Reduce baud rate to improve software serial reliability
#define TMC_BAUD_RATE 19200
#endif
// Not required for this board. Fails to compile otherwise. //
// PD0 is not connected on this board. // Heaters / Fans
#define TEMP_0_PIN PD0 //
// General use mosfets, useful for things like pumps and solenoids
#define FAN_PIN PE2 #define FAN_PIN PE2
#define FAN1_PIN PE3 #define FAN1_PIN PE3
#define FAN2_PIN PE4 #define FAN2_PIN PE4
@ -121,16 +155,26 @@
#define FAN_SOFT_PWM_REQUIRED #define FAN_SOFT_PWM_REQUIRED
// Neopixel Rings //
// Neopixel
//
#define NEOPIXEL_PIN PC7 #define NEOPIXEL_PIN PC7
#define NEOPIXEL2_PIN PC8 #define NEOPIXEL2_PIN PC8
//
// SPI // SPI
//
#define MISO_PIN PB4 #define MISO_PIN PB4
#define MOSI_PIN PB5 #define MOSI_PIN PB5
#define SCK_PIN PB3 #define SCK_PIN PB3
#define TMC_SW_MISO MISO_PIN
#define TMC_SW_MOSI MOSI_PIN
#define TMC_SW_SCK SCK_PIN
//
// I2C // I2C
//
#define I2C_SDA_PIN PB7 #define I2C_SDA_PIN PB7
#define I2C_SCL_PIN PB6 #define I2C_SCL_PIN PB6

Loading…
Cancel
Save