From 7b9ff164ccabccee77567c2611857e779f36fe48 Mon Sep 17 00:00:00 2001 From: Jason Smith Date: Thu, 17 Dec 2020 04:18:07 -0800 Subject: [PATCH] Balance CI tests (#20485) --- Marlin/src/inc/SanityCheck.h | 2 +- Marlin/src/pins/ramps/pins_FYSETC_F6_13.h | 3 +- buildroot/tests/FYSETC_F6_13-tests | 61 +++++++++++ buildroot/tests/LPC1769-tests | 20 +--- buildroot/tests/mega2560-tests | 119 +--------------------- buildroot/tests/mks_robin-tests | 8 ++ buildroot/tests/mks_robin_nano35-tests | 9 -- buildroot/tests/rambo-tests | 46 +++++++++ buildroot/tests/sanguino1284p-tests | 6 +- get_test_targets.py | 0 10 files changed, 125 insertions(+), 149 deletions(-) mode change 100644 => 100755 get_test_targets.py diff --git a/Marlin/src/inc/SanityCheck.h b/Marlin/src/inc/SanityCheck.h index 6c4c4cc340..be7d97e2ca 100644 --- a/Marlin/src/inc/SanityCheck.h +++ b/Marlin/src/inc/SanityCheck.h @@ -1916,7 +1916,7 @@ static_assert(hbm[Z_AXIS] >= 0, "HOMING_BUMP_MM.Z must be greater than or equal /** * LED Backlight Timeout */ -#if defined(LED_BACKLIGHT_TIMEOUT) && !(ENABLED(PSU_CONTROL) && EITHER(FYSETC_MINI_12864_2_0, FYSETC_MINI_12864_2_1)) +#if defined(LED_BACKLIGHT_TIMEOUT) && !(ENABLED(PSU_CONTROL) && ANY(FYSETC_MINI_12864_2_0, FYSETC_MINI_12864_2_1, FYSETC_242_OLED_12864)) #error "LED_BACKLIGHT_TIMEOUT requires a FYSETC Mini Panel and a Power Switch." #endif diff --git a/Marlin/src/pins/ramps/pins_FYSETC_F6_13.h b/Marlin/src/pins/ramps/pins_FYSETC_F6_13.h index 15ac2f447b..6133a6417e 100644 --- a/Marlin/src/pins/ramps/pins_FYSETC_F6_13.h +++ b/Marlin/src/pins/ramps/pins_FYSETC_F6_13.h @@ -226,7 +226,7 @@ #define DOGLCD_SCK 17 #define DOGLCD_A0 LCD_PINS_DC - #define KILL_PIN -1 // NC + #undef KILL_PIN #define NEOPIXEL_PIN 27 #else @@ -243,7 +243,6 @@ #define LCD_BACKLIGHT_PIN 27 #endif - #define KILL_PIN 41 #define LCD_RESET_PIN 23 // Must be high or open for LCD to operate normally. // Seems to work best if left open. diff --git a/buildroot/tests/FYSETC_F6_13-tests b/buildroot/tests/FYSETC_F6_13-tests index a3e9f4ef39..cc7f334099 100755 --- a/buildroot/tests/FYSETC_F6_13-tests +++ b/buildroot/tests/FYSETC_F6_13-tests @@ -14,5 +14,66 @@ opt_set MOTHERBOARD BOARD_FYSETC_F6_13 opt_enable DGUS_LCD_UI_FYSETC exec_test $1 $2 "FYSETC F6 1.3 with DGUS" "$3" +# +# Delta Config (generic) + UBL + ALLEN_KEY + EEPROM_SETTINGS + OLED_PANEL_TINYBOY2 +# +use_example_configs delta/generic +opt_set MOTHERBOARD BOARD_FYSETC_F6_13 +opt_enable RESTORE_LEVELING_AFTER_G28 EEPROM_SETTINGS EEPROM_CHITCHAT \ + Z_PROBE_ALLEN_KEY AUTO_BED_LEVELING_UBL \ + OLED_PANEL_TINYBOY2 MESH_EDIT_GFX_OVERLAY DELTA_CALIBRATION_MENU +opt_set LCD_LANGUAGE ko_KR +opt_set X_DRIVER_TYPE L6470 +opt_set Y_DRIVER_TYPE L6470 +opt_set Z_DRIVER_TYPE L6470 +opt_add L6470_CHAIN_SCK_PIN 53 +opt_add L6470_CHAIN_MISO_PIN 49 +opt_add L6470_CHAIN_MOSI_PIN 40 +opt_add L6470_CHAIN_SS_PIN 42 +opt_add "ENABLE_RESET_L64XX_CHIPS(V) NOOP" +exec_test $1 $2 "DELTA, RAMPS, L6470, UBL, Allen Key, EEPROM, OLED_PANEL_TINYBOY2..." "$3" + +# +# Test mixed TMC config +# +restore_configs +opt_set MOTHERBOARD BOARD_FYSETC_F6_13 +opt_set LCD_LANGUAGE vi +opt_set X_DRIVER_TYPE TMC2160 +opt_set Y_DRIVER_TYPE TMC5160 +opt_set Z_DRIVER_TYPE TMC2208_STANDALONE +opt_set E0_DRIVER_TYPE TMC2130 +opt_set X_MIN_ENDSTOP_INVERTING true +opt_set Y_MIN_ENDSTOP_INVERTING true +opt_enable REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER \ + MARLIN_BRICKOUT MARLIN_INVADERS MARLIN_SNAKE \ + MONITOR_DRIVER_STATUS STEALTHCHOP_XY STEALTHCHOP_Z STEALTHCHOP_E HYBRID_THRESHOLD \ + USE_ZMIN_PLUG SENSORLESS_HOMING TMC_DEBUG M114_DETAIL +exec_test $1 $2 "RAMPS | Mixed TMC | Sensorless | RRDFGSC | Games" "$3" + +# +# Delta Config (FLSUN AC because it's complex) +# +use_example_configs delta/FLSUN/auto_calibrate +opt_set MOTHERBOARD BOARD_FYSETC_F6_13 +exec_test $1 $2 "RAMPS 1.3 | DELTA | FLSUN AC Config" "$3" + +# +# SCARA with Mixed TMC +# +use_example_configs SCARA/Morgan +opt_set MOTHERBOARD BOARD_FYSETC_F6_13 +opt_set LCD_LANGUAGE es +opt_enable USE_ZMIN_PLUG FIX_MOUNTED_PROBE AUTO_BED_LEVELING_BILINEAR PAUSE_BEFORE_DEPLOY_STOW \ + FYSETC_242_OLED_12864 EEPROM_SETTINGS EEPROM_CHITCHAT M114_DETAIL Z_SAFE_HOMING \ + STEALTHCHOP_XY STEALTHCHOP_Z STEALTHCHOP_E HYBRID_THRESHOLD SENSORLESS_HOMING SQUARE_WAVE_STEPPING +opt_set X_MAX_ENDSTOP_INVERTING false +opt_set X_DRIVER_TYPE TMC2209 +opt_set Y_DRIVER_TYPE TMC2130 +opt_set Z_DRIVER_TYPE TMC2130_STANDALONE +opt_set E0_DRIVER_TYPE TMC2660 +opt_add X_HARDWARE_SERIAL Serial2 +exec_test $1 $2 "FYSETC_F6 | SCARA | Mixed TMC | EEPROM" "$3" + # clean up restore_configs diff --git a/buildroot/tests/LPC1769-tests b/buildroot/tests/LPC1769-tests index ebfa4cc8dc..0a61d42800 100755 --- a/buildroot/tests/LPC1769-tests +++ b/buildroot/tests/LPC1769-tests @@ -12,22 +12,6 @@ set -e use_example_configs Azteeg/X5GT exec_test $1 $2 "Azteeg X5GT Example Configuration" "$3" -restore_configs -opt_set MOTHERBOARD BOARD_SMOOTHIEBOARD -opt_set EXTRUDERS 2 -opt_set TEMP_SENSOR_1 -1 -opt_set TEMP_SENSOR_BED 5 -opt_enable VIKI2 SDSUPPORT ADAPTIVE_FAN_SLOWING NO_FAN_SLOWING_IN_PID_TUNING \ - FIX_MOUNTED_PROBE AUTO_BED_LEVELING_BILINEAR G29_RETRY_AND_RECOVER Z_MIN_PROBE_REPEATABILITY_TEST DEBUG_LEVELING_FEATURE \ - LEVEL_BED_CORNERS LEVEL_CORNERS_USE_PROBE LEVEL_CORNERS_VERIFY_RAISED \ - BABYSTEPPING BABYSTEP_XY BABYSTEP_ZPROBE_OFFSET BABYSTEP_ZPROBE_GFX_OVERLAY \ - PRINTCOUNTER NOZZLE_PARK_FEATURE NOZZLE_CLEAN_FEATURE SLOW_PWM_HEATERS PIDTEMPBED EEPROM_SETTINGS INCH_MODE_SUPPORT TEMPERATURE_UNITS_SUPPORT \ - Z_SAFE_HOMING ADVANCED_PAUSE_FEATURE PARK_HEAD_ON_PAUSE \ - LCD_INFO_MENU ARC_SUPPORT BEZIER_CURVE_SUPPORT EXTENDED_CAPABILITIES_REPORT AUTO_REPORT_TEMPERATURES SDCARD_SORT_ALPHA EMERGENCY_PARSER -opt_disable SD_PROCEDURE_DEPTH -opt_set GRID_MAX_POINTS_X 16 -exec_test $1 $2 "Smoothieboard with many features" "$3" - restore_configs opt_set MOTHERBOARD BOARD_SMOOTHIEBOARD opt_set EXTRUDERS 2 @@ -35,12 +19,12 @@ opt_set TEMP_SENSOR_1 -1 opt_set TEMP_SENSOR_BED 5 opt_enable TFTGLCD_PANEL_SPI SDSUPPORT ADAPTIVE_FAN_SLOWING NO_FAN_SLOWING_IN_PID_TUNING \ FIX_MOUNTED_PROBE AUTO_BED_LEVELING_BILINEAR G29_RETRY_AND_RECOVER Z_MIN_PROBE_REPEATABILITY_TEST DEBUG_LEVELING_FEATURE \ - BABYSTEPPING BABYSTEP_XY BABYSTEP_ZPROBE_OFFSET \ + BABYSTEPPING BABYSTEP_XY BABYSTEP_ZPROBE_OFFSET LEVEL_CORNERS_USE_PROBE LEVEL_CORNERS_VERIFY_RAISED \ PRINTCOUNTER NOZZLE_PARK_FEATURE NOZZLE_CLEAN_FEATURE SLOW_PWM_HEATERS PIDTEMPBED EEPROM_SETTINGS INCH_MODE_SUPPORT TEMPERATURE_UNITS_SUPPORT \ Z_SAFE_HOMING ADVANCED_PAUSE_FEATURE PARK_HEAD_ON_PAUSE \ LCD_INFO_MENU ARC_SUPPORT BEZIER_CURVE_SUPPORT EXTENDED_CAPABILITIES_REPORT AUTO_REPORT_TEMPERATURES SDCARD_SORT_ALPHA EMERGENCY_PARSER opt_set GRID_MAX_POINTS_X 16 -exec_test $1 $2 "Smoothieboard with TFTGLCD_PANEL_SPI" "$3" +exec_test $1 $2 "Smoothieboard with TFTGLCD_PANEL_SPI and many features" "$3" #restore_configs #opt_set MOTHERBOARD BOARD_AZTEEG_X5_MINI_WIFI diff --git a/buildroot/tests/mega2560-tests b/buildroot/tests/mega2560-tests index 0a17cacba1..12bbceab87 100755 --- a/buildroot/tests/mega2560-tests +++ b/buildroot/tests/mega2560-tests @@ -60,21 +60,6 @@ opt_disable SEGMENT_LEVELED_MOVES opt_enable BABYSTEPPING BABYSTEP_XY BABYSTEP_ZPROBE_OFFSET DOUBLECLICK_FOR_Z_BABYSTEPPING BABYSTEP_HOTEND_Z_OFFSET BABYSTEP_DISPLAY_TOTAL M114_DETAIL exec_test $1 $2 "Azteeg X3 Pro | EXTRUDERS 5 | RRDFGSC | UBL | LIN_ADVANCE | Sled Probe | Skew | JP-Kana | Babystep offsets ..." "$3" -# -# Test a Servo Probe -# ...with AUTO_BED_LEVELING_3POINT, DEBUG_LEVELING_FEATURE, EEPROM_SETTINGS, EEPROM_CHITCHAT, EXTENDED_CAPABILITIES_REPORT, and AUTO_REPORT_TEMPERATURES -# -restore_configs -opt_set LCD_LANGUAGE zh_CN -opt_set MMU_MODEL PRUSA_MMU2S -opt_set EXTRUDERS 5 -opt_set NUM_SERVOS 1 -opt_enable ZONESTAR_LCD Z_PROBE_SERVO_NR Z_SERVO_ANGLES DEACTIVATE_SERVOS_AFTER_MOVE BOOT_MARLIN_LOGO_ANIMATED \ - AUTO_BED_LEVELING_3POINT DEBUG_LEVELING_FEATURE EEPROM_SETTINGS EEPROM_CHITCHAT M114_DETAIL \ - NO_VOLUMETRICS EXTENDED_CAPABILITIES_REPORT AUTO_REPORT_TEMPERATURES AUTOTEMP G38_PROBE_TARGET JOYSTICK \ - MMU2_MENUS DIRECT_STEPPING DETECT_BROKEN_ENDSTOP \ - FILAMENT_RUNOUT_SENSOR NOZZLE_PARK_FEATURE ADVANCED_PAUSE_FEATURE Z_SAFE_HOMING -exec_test $1 $2 "RAMPS | ZONESTAR + Chinese | MMU2S | Servo | 3-Point + Debug | G38 ..." "$3" # # 5 runout sensors with distinct states @@ -100,27 +85,6 @@ opt_set FIL_RUNOUT4_PIN 46 opt_set FIL_RUNOUT5_PIN 47 exec_test $1 $2 "Multiple runout sensors (x5) | Distinct runout states" "$3" -# -# Test MINIRAMBO with PWM_MOTOR_CURRENT and many features -# -restore_configs -opt_set MOTHERBOARD BOARD_MEGACONTROLLER -opt_set LCD_LANGUAGE de -opt_enable EEPROM_SETTINGS EEPROM_CHITCHAT \ - MINIPANEL SDSUPPORT PCA9632 LCD_INFO_MENU SOUND_MENU_ITEM GCODE_REPEAT_MARKERS \ - AUTO_BED_LEVELING_BILINEAR PROBE_MANUALLY LCD_BED_LEVELING G26_MESH_VALIDATION MESH_EDIT_MENU \ - LIN_ADVANCE EXTRA_LIN_ADVANCE_K \ - INCH_MODE_SUPPORT TEMPERATURE_UNITS_SUPPORT EXPERIMENTAL_I2CBUS M100_FREE_MEMORY_WATCHER \ - NOZZLE_PARK_FEATURE NOZZLE_CLEAN_FEATURE \ - ADVANCED_PAUSE_FEATURE PARK_HEAD_ON_PAUSE ADVANCED_PAUSE_CONTINUOUS_PURGE FILAMENT_LOAD_UNLOAD_GCODES \ - PRINTCOUNTER SERVICE_NAME_1 SERVICE_INTERVAL_1 M114_DETAIL \ - USE_CONTROLLER_FAN CONTROLLER_FAN_EDITABLE -opt_set CONTROLLERFAN_SPEED_IDLE 128 -opt_add M100_FREE_MEMORY_DUMPER -opt_add M100_FREE_MEMORY_CORRUPTOR -opt_set PWM_MOTOR_CURRENT "{ 1300, 1300, 1250 }" -opt_set I2C_SLAVE_ADDRESS 63 -exec_test $1 $2 "MEGACONTROLLER | Minipanel | M100 | PWM_MOTOR_CURRENT | PRINTCOUNTER | Advanced Pause ..." "$3" # # Mixing Extruder with 5 steppers, Greek @@ -150,31 +114,6 @@ exec_test $1 $2 "Azteeg X3 | Mixing Extruder (x5) | Gradient Mix | Greek" "$3" #opt_enable COREXY #exec_test $1 $2 "Stuff" "$3" -# -# Test many less common options -# -restore_configs -opt_set MOTHERBOARD BOARD_MIGHTYBOARD_REVE -opt_set TEMP_SENSOR_0 -2 -opt_set DIGIPOT_I2C_NUM_CHANNELS 5 -opt_set LCD_LANGUAGE it -opt_set MIXING_STEPPERS 2 -opt_set SERVO_DELAY "{ 300, 300, 300 }" -opt_enable COREYX USE_XMAX_PLUG MIXING_EXTRUDER GRADIENT_MIX \ - BABYSTEPPING BABYSTEP_DISPLAY_TOTAL FILAMENT_LCD_DISPLAY \ - REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER MENU_ADDAUTOSTART SDSUPPORT SDCARD_SORT_ALPHA \ - ENDSTOP_NOISE_THRESHOLD FAN_SOFT_PWM \ - FIX_MOUNTED_PROBE AUTO_BED_LEVELING_LINEAR DEBUG_LEVELING_FEATURE FILAMENT_WIDTH_SENSOR PROBE_OFFSET_WIZARD \ - Z_SAFE_HOMING SHOW_TEMP_ADC_VALUES HOME_Y_BEFORE_X EMERGENCY_PARSER \ - SD_ABORT_ON_ENDSTOP_HIT HOST_ACTION_COMMANDS HOST_PROMPT_SUPPORT ADVANCED_OK M114_DETAIL \ - VOLUMETRIC_DEFAULT_ON NO_WORKSPACE_OFFSETS EXTRA_FAN_SPEED FWRETRACT \ - USE_CONTROLLER_FAN CONTROLLER_FAN_EDITABLE CONTROLLER_FAN_USE_Z_ONLY -opt_set FAN_MIN_PWM 50 -opt_set FAN_KICKSTART_TIME 100 -opt_set XY_FREQUENCY_LIMIT 15 -opt_add FILWIDTH_PIN 5 -exec_test $1 $2 "Mightyboard Rev. E | CoreXY, Gradient Mix | Endstop Int. | Home Y > X | FW Retract ..." "$3" - ######## Other Standard LCD/Panels ############## # # ULTRA_LCD @@ -277,71 +216,15 @@ exec_test $1 $2 "Formbot/T_Rex_3 example configuration." "$3" # # BQ Hephestos 2 #restore_configs -#use_example_configs Hephestos_2 +#use_example_configs BQ/Hephestos_2 #exec_test $1 $2 "Stuff" "$3" -# -# Delta Config (generic) + UBL + ALLEN_KEY + EEPROM_SETTINGS + OLED_PANEL_TINYBOY2 -# -use_example_configs delta/generic -opt_enable RESTORE_LEVELING_AFTER_G28 EEPROM_SETTINGS EEPROM_CHITCHAT \ - Z_PROBE_ALLEN_KEY AUTO_BED_LEVELING_UBL \ - OLED_PANEL_TINYBOY2 MESH_EDIT_GFX_OVERLAY DELTA_CALIBRATION_MENU -opt_set LCD_LANGUAGE ko_KR -opt_set X_DRIVER_TYPE L6470 -opt_set Y_DRIVER_TYPE L6470 -opt_set Z_DRIVER_TYPE L6470 -opt_add L6470_CHAIN_SCK_PIN 53 -opt_add L6470_CHAIN_MISO_PIN 49 -opt_add L6470_CHAIN_MOSI_PIN 40 -opt_add L6470_CHAIN_SS_PIN 42 -opt_add "ENABLE_RESET_L64XX_CHIPS(V) NOOP" -exec_test $1 $2 "DELTA, RAMPS, L6470, UBL, Allen Key, EEPROM, OLED_PANEL_TINYBOY2..." "$3" - -# -# Delta Config (FLSUN AC because it's complex) -# -use_example_configs delta/FLSUN/auto_calibrate -exec_test $1 $2 "RAMPS 1.3 | DELTA | FLSUN AC Config" "$3" - # # Makibox Config need to check board type for Teensy++ 2.0 # #use_example_configs makibox #exec_test $1 $2 "Stuff" "$3" -# -# Test mixed TMC config -# -restore_configs -opt_set LCD_LANGUAGE vi -opt_set X_DRIVER_TYPE TMC2160 -opt_set Y_DRIVER_TYPE TMC5160 -opt_set Z_DRIVER_TYPE TMC2208_STANDALONE -opt_set E0_DRIVER_TYPE TMC2130 -opt_set X_MIN_ENDSTOP_INVERTING true -opt_set Y_MIN_ENDSTOP_INVERTING true -opt_enable REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER \ - MARLIN_BRICKOUT MARLIN_INVADERS MARLIN_SNAKE \ - MONITOR_DRIVER_STATUS STEALTHCHOP_XY STEALTHCHOP_Z STEALTHCHOP_E HYBRID_THRESHOLD \ - USE_ZMIN_PLUG SENSORLESS_HOMING TMC_DEBUG M114_DETAIL -exec_test $1 $2 "RAMPS | Mixed TMC | Sensorless | RRDFGSC | Games" "$3" - -# -# SCARA with Mixed TMC -# -use_example_configs SCARA/Morgan -opt_set LCD_LANGUAGE es -opt_enable USE_ZMIN_PLUG FIX_MOUNTED_PROBE AUTO_BED_LEVELING_BILINEAR PAUSE_BEFORE_DEPLOY_STOW \ - MKS_12864OLED EEPROM_SETTINGS EEPROM_CHITCHAT M114_DETAIL Z_SAFE_HOMING \ - STEALTHCHOP_XY STEALTHCHOP_Z STEALTHCHOP_E HYBRID_THRESHOLD SENSORLESS_HOMING SQUARE_WAVE_STEPPING -opt_set X_MAX_ENDSTOP_INVERTING false -opt_set X_DRIVER_TYPE TMC2209 -opt_set Y_DRIVER_TYPE TMC2130 -opt_set Z_DRIVER_TYPE TMC2130_STANDALONE -opt_set E0_DRIVER_TYPE TMC2660 -exec_test $1 $2 "RAMPS | SCARA | Mixed TMC | EEPROM" "$3" - # # tvrrug Config need to check board type for sanguino atmega644p # diff --git a/buildroot/tests/mks_robin-tests b/buildroot/tests/mks_robin-tests index 3fccc87c59..652147f867 100755 --- a/buildroot/tests/mks_robin-tests +++ b/buildroot/tests/mks_robin-tests @@ -10,5 +10,13 @@ set -e use_example_configs Mks/Robin exec_test $1 $2 "MKS Robin config (FSMC Color UI)" "$3" +# +# MKS Robin LVGL FSMC +# +use_example_configs Mks/Robin +opt_disable TFT_CLASSIC_UI TFT_COLOR_UI TOUCH_SCREEN TFT_RES_320x240 +opt_enable TFT_LVGL_UI TFT_RES_480x320 +exec_test $1 $2 "MKS Robin nano v1.2 LVGL FSMC" "$3" + # cleanup restore_configs diff --git a/buildroot/tests/mks_robin_nano35-tests b/buildroot/tests/mks_robin_nano35-tests index 391566f6d7..3c5d1bb66f 100755 --- a/buildroot/tests/mks_robin_nano35-tests +++ b/buildroot/tests/mks_robin_nano35-tests @@ -24,15 +24,6 @@ opt_disable TFT_INTERFACE_FSMC opt_enable TFT_INTERFACE_SPI exec_test $1 $2 "MKS Robin v2 nano Emulated DOGM SPI" "$3" -# -# MKS Robin nano v1.2 LVGL FSMC -# -use_example_configs Mks/Robin -opt_set MOTHERBOARD BOARD_MKS_ROBIN_NANO -opt_disable TFT_CLASSIC_UI TFT_COLOR_UI TOUCH_SCREEN TFT_RES_320x240 -opt_enable TFT_LVGL_UI TFT_RES_480x320 -exec_test $1 $2 "MKS Robin nano v1.2 LVGL FSMC" "$3" - # # MKS Robin v2 nano LVGL SPI # (Robin v2 nano has no FSMC interface) diff --git a/buildroot/tests/rambo-tests b/buildroot/tests/rambo-tests index 6d2ef4f58a..f93b2d14f2 100755 --- a/buildroot/tests/rambo-tests +++ b/buildroot/tests/rambo-tests @@ -81,5 +81,51 @@ opt_set Z_DRIVER_TYPE TMC2130 opt_set E0_DRIVER_TYPE TMC2130 exec_test $1 $2 "Einsy RAMBo with TMC2130" "$3" +# +# Test MINIRAMBO with PWM_MOTOR_CURRENT and many features +# +restore_configs +opt_set MOTHERBOARD BOARD_MINIRAMBO +opt_enable EEPROM_SETTINGS EEPROM_CHITCHAT REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER \ + SDSUPPORT PCA9632 SOUND_MENU_ITEM GCODE_REPEAT_MARKERS \ + AUTO_BED_LEVELING_BILINEAR PROBE_MANUALLY LCD_BED_LEVELING G26_MESH_VALIDATION MESH_EDIT_MENU \ + LIN_ADVANCE EXTRA_LIN_ADVANCE_K \ + INCH_MODE_SUPPORT TEMPERATURE_UNITS_SUPPORT EXPERIMENTAL_I2CBUS M100_FREE_MEMORY_WATCHER \ + NOZZLE_PARK_FEATURE NOZZLE_CLEAN_FEATURE \ + ADVANCED_PAUSE_FEATURE PARK_HEAD_ON_PAUSE ADVANCED_PAUSE_CONTINUOUS_PURGE FILAMENT_LOAD_UNLOAD_GCODES \ + PRINTCOUNTER SERVICE_NAME_1 SERVICE_INTERVAL_1 M114_DETAIL +opt_set CONTROLLERFAN_SPEED_IDLE 128 +opt_add M100_FREE_MEMORY_DUMPER +opt_add M100_FREE_MEMORY_CORRUPTOR +opt_set PWM_MOTOR_CURRENT "{ 1300, 1300, 1250 }" +opt_set I2C_SLAVE_ADDRESS 63 +exec_test $1 $2 "MINIRAMBO | RRDGFSC | M100 | PWM_MOTOR_CURRENT | PRINTCOUNTER | Advanced Pause ..." "$3" + +# +# Test many less common options +# +restore_configs +opt_set MOTHERBOARD BOARD_RAMBO +opt_set TEMP_SENSOR_0 -2 +opt_set DIGIPOT_I2C_NUM_CHANNELS 5 +opt_set LCD_LANGUAGE it +opt_set MIXING_STEPPERS 2 +opt_set SERVO_DELAY "{ 300, 300, 300 }" +opt_enable COREYX USE_XMAX_PLUG MIXING_EXTRUDER GRADIENT_MIX \ + BABYSTEPPING BABYSTEP_DISPLAY_TOTAL FILAMENT_LCD_DISPLAY \ + REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER MENU_ADDAUTOSTART SDSUPPORT SDCARD_SORT_ALPHA \ + ENDSTOP_NOISE_THRESHOLD FAN_SOFT_PWM \ + FIX_MOUNTED_PROBE AUTO_BED_LEVELING_LINEAR DEBUG_LEVELING_FEATURE FILAMENT_WIDTH_SENSOR PROBE_OFFSET_WIZARD \ + Z_SAFE_HOMING SHOW_TEMP_ADC_VALUES HOME_Y_BEFORE_X EMERGENCY_PARSER \ + SD_ABORT_ON_ENDSTOP_HIT HOST_ACTION_COMMANDS HOST_PROMPT_SUPPORT ADVANCED_OK M114_DETAIL \ + VOLUMETRIC_DEFAULT_ON NO_WORKSPACE_OFFSETS EXTRA_FAN_SPEED FWRETRACT \ + USE_CONTROLLER_FAN CONTROLLER_FAN_EDITABLE CONTROLLER_FAN_USE_Z_ONLY +opt_set CONTROLLER_FAN_PIN X_MAX_PIN +opt_set FAN_MIN_PWM 50 +opt_set FAN_KICKSTART_TIME 100 +opt_set XY_FREQUENCY_LIMIT 15 +opt_add FILWIDTH_PIN 5 +exec_test $1 $2 "Rambo | CoreXY, Gradient Mix | Endstop Int. | Home Y > X | FW Retract ..." "$3" + # clean up restore_configs diff --git a/buildroot/tests/sanguino1284p-tests b/buildroot/tests/sanguino1284p-tests index 748d2a8fa3..a513f095f9 100755 --- a/buildroot/tests/sanguino1284p-tests +++ b/buildroot/tests/sanguino1284p-tests @@ -11,7 +11,11 @@ set -e # restore_configs opt_set MOTHERBOARD BOARD_SANGUINOLOLU_12 -exec_test $1 $2 "Default Configuration" "$3" +opt_set LCD_LANGUAGE de +opt_enable MINIPANEL USE_CONTROLLER_FAN CONTROLLER_FAN_EDITABLE +opt_set CONTROLLER_FAN_PIN 27 +exec_test $1 $2 "Default Configuration | MINIPANAL | CONTROLLER_FAN" "$3" + # clean up restore_configs diff --git a/get_test_targets.py b/get_test_targets.py old mode 100644 new mode 100755