Bring configs up to date

7 years ago · 77c2d810f9
24 changed files with 52 additions and 36 deletions
--- a/Marlin/src/config/examples/Creality/CR-10/Configuration_adv.h
+++ b/Marlin/src/config/examples/Creality/CR-10/Configuration_adv.h
--- a/Marlin/src/config/examples/Creality/CR-10S/Configuration.h
+++ b/Marlin/src/config/examples/Creality/CR-10S/Configuration.h
@ -37,7 +37,7 @@
 */
 #ifndef CONFIGURATION_H
 #define CONFIGURATION_H
-#define CONFIGURATION_H_VERSION 010107
+#define CONFIGURATION_H_VERSION 020000
 //===========================================================================
 //============================= Getting Started =============================
@ -59,14 +59,14 @@
 //============================= DELTA Printer ===============================
 //===========================================================================
 // For a Delta printer start with one of the configuration files in the
-// example_configurations/delta directory and customize for your machine.
+// config/examples/delta directory and customize for your machine.
 //
 //===========================================================================
 //============================= SCARA Printer ===============================
 //===========================================================================
 // For a SCARA printer start with the configuration files in
-// example_configurations/SCARA and customize for your machine.
+// config/examples/SCARA and customize for your machine.
 //
 // @section info
--- a/Marlin/src/config/examples/Creality/CR-10S/Configuration_adv.h
+++ b/Marlin/src/config/examples/Creality/CR-10S/Configuration_adv.h
@ -32,7 +32,7 @@
 */
 #ifndef CONFIGURATION_ADV_H
 #define CONFIGURATION_ADV_H
-#define CONFIGURATION_ADV_H_VERSION 010107
+#define CONFIGURATION_ADV_H_VERSION 020000
 // @section temperature
--- a/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration.h
+++ b/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration.h
@ -815,7 +815,7 @@
 * - Use 'M211' to set software endstops on/off or report current state
 */
-// If enabled, axes won't move below MIN_POS in response to movement commands.
+// Min software endstops constrain movement within minimum coordinate bounds
 //#define MIN_SOFTWARE_ENDSTOPS
 #if ENABLED(MIN_SOFTWARE_ENDSTOPS)
  #define MIN_SOFTWARE_ENDSTOP_X
@ -823,7 +823,7 @@
  #define MIN_SOFTWARE_ENDSTOP_Z
 #endif
-// If enabled, axes won't move above MAX_POS in response to movement commands.
+// Max software endstops constrain movement within maximum coordinate bounds
 #define MAX_SOFTWARE_ENDSTOPS
 #if ENABLED(MAX_SOFTWARE_ENDSTOPS)
  #define MAX_SOFTWARE_ENDSTOP_X
--- a/Marlin/src/config/examples/Micromake/C1/basic/Configuration.h
+++ b/Marlin/src/config/examples/Micromake/C1/basic/Configuration.h
@ -813,7 +813,7 @@
 * - Use 'M211' to set software endstops on/off or report current state
 */
-// Min software endstops curtail movement below minimum coordinate bounds
+// Min software endstops constrain movement within minimum coordinate bounds
 #define MIN_SOFTWARE_ENDSTOPS
 #if ENABLED(MIN_SOFTWARE_ENDSTOPS)
  #define MIN_SOFTWARE_ENDSTOP_X
@ -821,7 +821,7 @@
  #define MIN_SOFTWARE_ENDSTOP_Z
 #endif
-// Max software endstops curtail movement above maximum coordinate bounds
+// Max software endstops constrain movement within maximum coordinate bounds
 #define MAX_SOFTWARE_ENDSTOPS
 #if ENABLED(MAX_SOFTWARE_ENDSTOPS)
  #define MAX_SOFTWARE_ENDSTOP_X
--- a/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration.h
+++ b/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration.h
@ -813,7 +813,7 @@
 * - Use 'M211' to set software endstops on/off or report current state
 */
-// Min software endstops curtail movement below minimum coordinate bounds
+// Min software endstops constrain movement within minimum coordinate bounds
 #define MIN_SOFTWARE_ENDSTOPS
 #if ENABLED(MIN_SOFTWARE_ENDSTOPS)
  #define MIN_SOFTWARE_ENDSTOP_X
@ -821,7 +821,7 @@
  #define MIN_SOFTWARE_ENDSTOP_Z
 #endif
-// Max software endstops curtail movement above maximum coordinate bounds
+// Max software endstops constrain movement within maximum coordinate bounds
 #define MAX_SOFTWARE_ENDSTOPS
 #if ENABLED(MAX_SOFTWARE_ENDSTOPS)
  #define MAX_SOFTWARE_ENDSTOP_X
--- a/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration_adv.h
+++ b/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration_adv.h
@ -512,7 +512,6 @@
  #define SD_DETECT_INVERTED
  #define SD_FINISHED_STEPPERRELEASE true          // Disable steppers when SD Print is finished
  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
  // Reverse SD sort to show "more recent" files first, according to the card's FAT.
--- a/Marlin/src/config/examples/Sanguinololu/Configuration_adv.h
+++ b/Marlin/src/config/examples/Sanguinololu/Configuration_adv.h
@ -222,6 +222,17 @@
 #define EXTRUDER_AUTO_FAN_TEMPERATURE 50
 #define EXTRUDER_AUTO_FAN_SPEED   255  // == full speed
 /**
 * Part-Cooling Fan Multiplexer
 *
 * This feature allows you to digitally multiplex the fan output.
 * The multiplexer is automatically switched at tool-change.
 * Set FANMUX[012]_PINs below for up to 2, 4, or 8 multiplexed fans.
 */
 #define FANMUX0_PIN -1
 #define FANMUX1_PIN -1
 #define FANMUX2_PIN -1
 /**
 * M355 Case Light on-off / brightness
 */
--- a/Marlin/src/config/examples/Tronxy/X1/Configuration.h
+++ b/Marlin/src/config/examples/Tronxy/X1/Configuration.h
@ -800,7 +800,7 @@
 * - Use 'M211' to set software endstops on/off or report current state
 */
-// Min software endstops curtail movement below minimum coordinate bounds
+// Min software endstops constrain movement within minimum coordinate bounds
 #define MIN_SOFTWARE_ENDSTOPS
 #if ENABLED(MIN_SOFTWARE_ENDSTOPS)
  #define MIN_SOFTWARE_ENDSTOP_X
@ -808,7 +808,7 @@
  #define MIN_SOFTWARE_ENDSTOP_Z
 #endif
-// Max software endstops curtail movement above maximum coordinate bounds
+// Max software endstops constrain movement within maximum coordinate bounds
 #define MAX_SOFTWARE_ENDSTOPS
 #if ENABLED(MAX_SOFTWARE_ENDSTOPS)
  #define MAX_SOFTWARE_ENDSTOP_X
--- a/Marlin/src/config/examples/Velleman/K8200/Configuration_adv.h
+++ b/Marlin/src/config/examples/Velleman/K8200/Configuration_adv.h
@ -527,10 +527,12 @@
  #define SD_FINISHED_STEPPERRELEASE true          // Disable steppers when SD Print is finished
  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
-  #define SDCARD_RATHERRECENTFIRST  //reverse file order of sd card menu display. Its sorted practically after the file system block order.
+  // Reverse SD sort to show "more recent" files first, according to the card's FAT.
-  // if a file is deleted, it frees a block. hence, the order is not purely chronological. To still have auto0.g accessible, there is again the option to do that.
+  // Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.
-  // using:
+  #define SDCARD_RATHERRECENTFIRST
-  #define MENU_ADDAUTOSTART
+
  // Add an option in the menu to run all auto#.g files
  //#define MENU_ADDAUTOSTART
  /**
   * Sort SD file listings in alphabetical order.
--- a/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration.h
+++ b/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration.h
@ -1,4 +1,4 @@
-/**
+/**
 * Marlin 3D Printer Firmware
 * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
 *
@ -939,7 +939,7 @@
 * - Use 'M211' to set software endstops on/off or report current state
 */
-// Min software endstops curtail movement below minimum coordinate bounds
+// Min software endstops constrain movement within minimum coordinate bounds
 //#define MIN_SOFTWARE_ENDSTOPS
 #if ENABLED(MIN_SOFTWARE_ENDSTOPS)
  #define MIN_SOFTWARE_ENDSTOP_X
@ -947,7 +947,7 @@
  #define MIN_SOFTWARE_ENDSTOP_Z
 #endif
-// Max software endstops curtail movement above maximum coordinate bounds
+// Max software endstops constrain movement within maximum coordinate bounds
 #define MAX_SOFTWARE_ENDSTOPS
 #if ENABLED(MAX_SOFTWARE_ENDSTOPS)
  #define MAX_SOFTWARE_ENDSTOP_X
--- a/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration.h
+++ b/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration.h
@ -1,4 +1,4 @@
-/**
+/**
 * Marlin 3D Printer Firmware
 * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
 *
@ -1066,6 +1066,11 @@
  //#define PROBE_Y_FIRST
  #if ENABLED(AUTO_BED_LEVELING_BILINEAR)
    // Beyond the probed grid, continue the implied tilt?
    // Default is to maintain the height of the nearest edge.
    //#define EXTRAPOLATE_BEYOND_GRID
    //
    // Experimental Subdivision of the grid by Catmull-Rom method.
    // Synthesizes intermediate points to produce a more detailed mesh.
--- a/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h
+++ b/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h
@ -1,4 +1,4 @@
-/**
+/**
 * Marlin 3D Printer Firmware
 * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
 *
--- a/Marlin/src/config/examples/delta/generic/Configuration.h
+++ b/Marlin/src/config/examples/delta/generic/Configuration.h
@ -1,4 +1,4 @@
-/**
+/**
 * Marlin 3D Printer Firmware
 * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
 *
--- a/Marlin/src/config/examples/delta/generic/Configuration_adv.h
+++ b/Marlin/src/config/examples/delta/generic/Configuration_adv.h
@ -1,4 +1,4 @@
-/**
+/**
 * Marlin 3D Printer Firmware
 * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
 *
--- a/Marlin/src/config/examples/delta/kossel_mini/Configuration.h
+++ b/Marlin/src/config/examples/delta/kossel_mini/Configuration.h
@ -1,4 +1,4 @@
-/**
+/**
 * Marlin 3D Printer Firmware
 * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
 *
--- a/Marlin/src/config/examples/delta/kossel_mini/Configuration_adv.h
+++ b/Marlin/src/config/examples/delta/kossel_mini/Configuration_adv.h
@ -1,4 +1,4 @@
-/**
+/**
 * Marlin 3D Printer Firmware
 * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
 *
--- a/Marlin/src/config/examples/delta/kossel_pro/Configuration.h
+++ b/Marlin/src/config/examples/delta/kossel_pro/Configuration.h
@ -1,4 +1,4 @@
-/**
+/**
 * Marlin 3D Printer Firmware
 * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
 *
--- a/Marlin/src/config/examples/delta/kossel_pro/Configuration_adv.h
+++ b/Marlin/src/config/examples/delta/kossel_pro/Configuration_adv.h
@ -1,4 +1,4 @@
-/**
+/**
 * Marlin 3D Printer Firmware
 * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
 *
--- a/Marlin/src/config/examples/delta/kossel_xl/Configuration.h
+++ b/Marlin/src/config/examples/delta/kossel_xl/Configuration.h
@ -1,4 +1,4 @@
-/**
+/**
 * Marlin 3D Printer Firmware
 * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
 *
@ -938,7 +938,7 @@
 * - Use 'M211' to set software endstops on/off or report current state
 */
-// Min software endstops curtail movement below minimum coordinate bounds
+// Min software endstops constrain movement within minimum coordinate bounds
 //#define MIN_SOFTWARE_ENDSTOPS
 #if ENABLED(MIN_SOFTWARE_ENDSTOPS)
  #define MIN_SOFTWARE_ENDSTOP_X
@ -946,7 +946,7 @@
  #define MIN_SOFTWARE_ENDSTOP_Z
 #endif
-// Max software endstops curtail movement above maximum coordinate bounds
+// Max software endstops constrain movement within maximum coordinate bounds
 #define MAX_SOFTWARE_ENDSTOPS
 #if ENABLED(MAX_SOFTWARE_ENDSTOPS)
  #define MAX_SOFTWARE_ENDSTOP_X
--- a/Marlin/src/config/examples/delta/kossel_xl/Configuration_adv.h
+++ b/Marlin/src/config/examples/delta/kossel_xl/Configuration_adv.h
@ -1,4 +1,4 @@
-/**
+/**
 * Marlin 3D Printer Firmware
 * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
 *
--- a/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration.h
+++ b/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration.h
@ -823,7 +823,7 @@
 * - Use 'M211' to set software endstops on/off or report current state
 */
-// Min software endstops curtail movement below minimum coordinate bounds
+// Min software endstops constrain movement within minimum coordinate bounds
 //#define MIN_SOFTWARE_ENDSTOPS
 #if ENABLED(MIN_SOFTWARE_ENDSTOPS)
  #define MIN_SOFTWARE_ENDSTOP_X
@ -831,7 +831,7 @@
  #define MIN_SOFTWARE_ENDSTOP_Z
 #endif
-// Max software endstops curtail movement above maximum coordinate bounds
+// Max software endstops constrain movement within maximum coordinate bounds
 #define MAX_SOFTWARE_ENDSTOPS
 #if ENABLED(MAX_SOFTWARE_ENDSTOPS)
  #define MAX_SOFTWARE_ENDSTOP_X
--- a/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration_adv.h
+++ b/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration_adv.h
@ -1559,7 +1559,6 @@
 * Fully assembled MAX7219 boards can be found on the internet for under $2(US).
 * For example, see https://www.ebay.com/sch/i.html?_nkw=332349290049
 */
 #define MAX7219_DEBUG
 #if ENABLED(MAX7219_DEBUG)
  #define MAX7219_CLK_PIN   64  // 77 on Re-ARM       // Configuration of the 3 pins to control the display
--- a/Marlin/src/config/examples/wt150/Configuration.h
+++ b/Marlin/src/config/examples/wt150/Configuration.h
@ -766,7 +766,7 @@
 #define INVERT_Y_DIR false
 #define INVERT_Z_DIR false
-// Enable this option for Toshiba steppers
+// Enable this option for Toshiba stepper drivers
 //#define CONFIG_STEPPERS_TOSHIBA
 // @section extruder