Added circle nozzle cleaning parameters to example configurations

8 years ago · 7698c5617a
20 changed files with 260 additions and 40 deletions
--- a/Marlin/example_configurations/Cartesio/Configuration.h
+++ b/Marlin/example_configurations/Cartesio/Configuration.h
@ -96,7 +96,7 @@
 //
 // Marlin now allow you to have a vendor boot image to be displayed on machine
 // start. When SHOW_CUSTOM_BOOTSCREEN is defined Marlin will first show your
-// custom boot image and them the default Marlin boot image is shown.
+// custom boot image and then the default Marlin boot image is shown.
 //
 // We suggest for you to take advantage of this new feature and keep the Marlin
 // boot image unmodified. For an example have a look at the bq Hephestos 2
@ -1000,6 +1000,10 @@
 //                       |________|_________|_________|
 //                           T1        T2        T3
 //
+//   P2: This starts a circular pattern with circle with middle in
+//       NOZZLE_CLEAN_CIRCLE_MIDDLE radius of R and stroke count of S.
+//       Before starting the circle nozzle goes to NOZZLE_CLEAN_START_POINT.
+//
 // Caveats: End point Z should use the same value as Start point Z.
 //
 // Attention: This is an EXPERIMENTAL feature, in the future the G-code arguments
@ -1010,7 +1014,7 @@
 #if ENABLED(NOZZLE_CLEAN_FEATURE)
  // Default number of pattern repetitions
  #define NOZZLE_CLEAN_STROKES  12
-  
+
  // Default number of triangles
  #define NOZZLE_CLEAN_TRIANGLES  3

@ -1018,6 +1022,13 @@
  #define NOZZLE_CLEAN_START_POINT { 30, 30, (Z_MIN_POS + 1)}
  #define NOZZLE_CLEAN_END_POINT   {100, 60, (Z_MIN_POS + 1)}

+  // Circular pattern radius
+  #define NOZZLE_CLEAN_CIRCLE_RADIUS 6.5
+  // Circular pattern circle fragments number
+  #define NOZZLE_CLEAN_CIRCLE_FN 10
+  // Middle point of circle
+  #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT
+
  // Moves the nozzle to the initial position
  #define NOZZLE_CLEAN_GOBACK
 #endif
--- a/Marlin/example_configurations/Felix/Configuration.h
+++ b/Marlin/example_configurations/Felix/Configuration.h
@ -96,7 +96,7 @@
 //
 // Marlin now allow you to have a vendor boot image to be displayed on machine
 // start. When SHOW_CUSTOM_BOOTSCREEN is defined Marlin will first show your
-// custom boot image and them the default Marlin boot image is shown.
+// custom boot image and then the default Marlin boot image is shown.
 //
 // We suggest for you to take advantage of this new feature and keep the Marlin
 // boot image unmodified. For an example have a look at the bq Hephestos 2
@ -983,6 +983,10 @@
 //                       |________|_________|_________|
 //                           T1        T2        T3
 //
+//   P2: This starts a circular pattern with circle with middle in
+//       NOZZLE_CLEAN_CIRCLE_MIDDLE radius of R and stroke count of S.
+//       Before starting the circle nozzle goes to NOZZLE_CLEAN_START_POINT.
+//
 // Caveats: End point Z should use the same value as Start point Z.
 //
 // Attention: This is an EXPERIMENTAL feature, in the future the G-code arguments
@ -993,7 +997,7 @@
 #if ENABLED(NOZZLE_CLEAN_FEATURE)
  // Default number of pattern repetitions
  #define NOZZLE_CLEAN_STROKES  12
-  
+
  // Default number of triangles
  #define NOZZLE_CLEAN_TRIANGLES  3

@ -1001,6 +1005,13 @@
  #define NOZZLE_CLEAN_START_POINT { 30, 30, (Z_MIN_POS + 1)}
  #define NOZZLE_CLEAN_END_POINT   {100, 60, (Z_MIN_POS + 1)}

+  // Circular pattern radius
+  #define NOZZLE_CLEAN_CIRCLE_RADIUS 6.5
+  // Circular pattern circle fragments number
+  #define NOZZLE_CLEAN_CIRCLE_FN 10
+  // Middle point of circle
+  #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT
+
  // Moves the nozzle to the initial position
  #define NOZZLE_CLEAN_GOBACK
 #endif
--- a/Marlin/example_configurations/Felix/DUAL/Configuration.h
+++ b/Marlin/example_configurations/Felix/DUAL/Configuration.h
@ -96,7 +96,7 @@
 //
 // Marlin now allow you to have a vendor boot image to be displayed on machine
 // start. When SHOW_CUSTOM_BOOTSCREEN is defined Marlin will first show your
-// custom boot image and them the default Marlin boot image is shown.
+// custom boot image and then the default Marlin boot image is shown.
 //
 // We suggest for you to take advantage of this new feature and keep the Marlin
 // boot image unmodified. For an example have a look at the bq Hephestos 2
@ -983,6 +983,10 @@
 //                       |________|_________|_________|
 //                           T1        T2        T3
 //
+//   P2: This starts a circular pattern with circle with middle in
+//       NOZZLE_CLEAN_CIRCLE_MIDDLE radius of R and stroke count of S.
+//       Before starting the circle nozzle goes to NOZZLE_CLEAN_START_POINT.
+//
 // Caveats: End point Z should use the same value as Start point Z.
 //
 // Attention: This is an EXPERIMENTAL feature, in the future the G-code arguments
@ -993,7 +997,7 @@
 #if ENABLED(NOZZLE_CLEAN_FEATURE)
  // Default number of pattern repetitions
  #define NOZZLE_CLEAN_STROKES  12
-  
+
  // Default number of triangles
  #define NOZZLE_CLEAN_TRIANGLES  3

@ -1001,6 +1005,13 @@
  #define NOZZLE_CLEAN_START_POINT { 30, 30, (Z_MIN_POS + 1)}
  #define NOZZLE_CLEAN_END_POINT   {100, 60, (Z_MIN_POS + 1)}

+  // Circular pattern radius
+  #define NOZZLE_CLEAN_CIRCLE_RADIUS 6.5
+  // Circular pattern circle fragments number
+  #define NOZZLE_CLEAN_CIRCLE_FN 10
+  // Middle point of circle
+  #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT
+
  // Moves the nozzle to the initial position
  #define NOZZLE_CLEAN_GOBACK
 #endif
--- a/Marlin/example_configurations/Hephestos/Configuration.h
+++ b/Marlin/example_configurations/Hephestos/Configuration.h
@ -96,7 +96,7 @@
 //
 // Marlin now allow you to have a vendor boot image to be displayed on machine
 // start. When SHOW_CUSTOM_BOOTSCREEN is defined Marlin will first show your
-// custom boot image and them the default Marlin boot image is shown.
+// custom boot image and then the default Marlin boot image is shown.
 //
 // We suggest for you to take advantage of this new feature and keep the Marlin
 // boot image unmodified. For an example have a look at the bq Hephestos 2
@ -992,6 +992,10 @@
 //                       |________|_________|_________|
 //                           T1        T2        T3
 //
+//   P2: This starts a circular pattern with circle with middle in
+//       NOZZLE_CLEAN_CIRCLE_MIDDLE radius of R and stroke count of S.
+//       Before starting the circle nozzle goes to NOZZLE_CLEAN_START_POINT.
+//
 // Caveats: End point Z should use the same value as Start point Z.
 //
 // Attention: This is an EXPERIMENTAL feature, in the future the G-code arguments
@ -1002,7 +1006,7 @@
 #if ENABLED(NOZZLE_CLEAN_FEATURE)
  // Default number of pattern repetitions
  #define NOZZLE_CLEAN_STROKES  12
-  
+
  // Default number of triangles
  #define NOZZLE_CLEAN_TRIANGLES  3

@ -1010,6 +1014,13 @@
  #define NOZZLE_CLEAN_START_POINT { 30, 30, (Z_MIN_POS + 1)}
  #define NOZZLE_CLEAN_END_POINT   {100, 60, (Z_MIN_POS + 1)}

+  // Circular pattern radius
+  #define NOZZLE_CLEAN_CIRCLE_RADIUS 6.5
+  // Circular pattern circle fragments number
+  #define NOZZLE_CLEAN_CIRCLE_FN 10
+  // Middle point of circle
+  #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT
+
  // Moves the nozzle to the initial position
  #define NOZZLE_CLEAN_GOBACK
 #endif
--- a/Marlin/example_configurations/Hephestos_2/Configuration.h
+++ b/Marlin/example_configurations/Hephestos_2/Configuration.h
@ -96,7 +96,7 @@
 //
 // Marlin now allow you to have a vendor boot image to be displayed on machine
 // start. When SHOW_CUSTOM_BOOTSCREEN is defined Marlin will first show your
-// custom boot image and them the default Marlin boot image is shown.
+// custom boot image and then the default Marlin boot image is shown.
 //
 // We suggest for you to take advantage of this new feature and keep the Marlin
 // boot image unmodified. For an example have a look at the bq Hephestos 2
@ -994,6 +994,10 @@
 //                       |________|_________|_________|
 //                           T1        T2        T3
 //
+//   P2: This starts a circular pattern with circle with middle in
+//       NOZZLE_CLEAN_CIRCLE_MIDDLE radius of R and stroke count of S.
+//       Before starting the circle nozzle goes to NOZZLE_CLEAN_START_POINT.
+//
 // Caveats: End point Z should use the same value as Start point Z.
 //
 // Attention: This is an EXPERIMENTAL feature, in the future the G-code arguments
@ -1004,7 +1008,7 @@
 #if ENABLED(NOZZLE_CLEAN_FEATURE)
  // Default number of pattern repetitions
  #define NOZZLE_CLEAN_STROKES  12
-  
+
  // Default number of triangles
  #define NOZZLE_CLEAN_TRIANGLES  3

@ -1012,6 +1016,13 @@
  #define NOZZLE_CLEAN_START_POINT { X_MIN_POS + 10, Y_MAX_POS - 9, (Z_MIN_POS + 0.5)}
  #define NOZZLE_CLEAN_END_POINT   { X_MIN_POS + 90, Y_MAX_POS - 0, (Z_MIN_POS + 0.5)}

+  // Circular pattern radius
+  #define NOZZLE_CLEAN_CIRCLE_RADIUS 6.5
+  // Circular pattern circle fragments number
+  #define NOZZLE_CLEAN_CIRCLE_FN 10
+  // Middle point of circle
+  #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT
+
  // Moves the nozzle to the initial position
  //#define NOZZLE_CLEAN_GOBACK
 #endif
--- a/Marlin/example_configurations/K8200/Configuration.h
+++ b/Marlin/example_configurations/K8200/Configuration.h
@ -112,7 +112,7 @@
 //
 // Marlin now allow you to have a vendor boot image to be displayed on machine
 // start. When SHOW_CUSTOM_BOOTSCREEN is defined Marlin will first show your
-// custom boot image and them the default Marlin boot image is shown.
+// custom boot image and then the default Marlin boot image is shown.
 //
 // We suggest for you to take advantage of this new feature and keep the Marlin
 // boot image unmodified. For an example have a look at the bq Hephestos 2
@ -1029,6 +1029,10 @@
 //                       |________|_________|_________|
 //                           T1        T2        T3
 //
+//   P2: This starts a circular pattern with circle with middle in
+//       NOZZLE_CLEAN_CIRCLE_MIDDLE radius of R and stroke count of S.
+//       Before starting the circle nozzle goes to NOZZLE_CLEAN_START_POINT.
+//
 // Caveats: End point Z should use the same value as Start point Z.
 //
 // Attention: This is an EXPERIMENTAL feature, in the future the G-code arguments
@ -1039,7 +1043,7 @@
 #if ENABLED(NOZZLE_CLEAN_FEATURE)
  // Default number of pattern repetitions
  #define NOZZLE_CLEAN_STROKES  12
-  
+
  // Default number of triangles
  #define NOZZLE_CLEAN_TRIANGLES  3

@ -1047,6 +1051,13 @@
  #define NOZZLE_CLEAN_START_POINT { 30, 30, (Z_MIN_POS + 1)}
  #define NOZZLE_CLEAN_END_POINT   {100, 60, (Z_MIN_POS + 1)}

+  // Circular pattern radius
+  #define NOZZLE_CLEAN_CIRCLE_RADIUS 6.5
+  // Circular pattern circle fragments number
+  #define NOZZLE_CLEAN_CIRCLE_FN 10
+  // Middle point of circle
+  #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT
+
  // Moves the nozzle to the initial position
  #define NOZZLE_CLEAN_GOBACK
 #endif
--- a/Marlin/example_configurations/K8400/Configuration.h
+++ b/Marlin/example_configurations/K8400/Configuration.h
@ -96,7 +96,7 @@
 //
 // Marlin now allow you to have a vendor boot image to be displayed on machine
 // start. When SHOW_CUSTOM_BOOTSCREEN is defined Marlin will first show your
-// custom boot image and them the default Marlin boot image is shown.
+// custom boot image and then the default Marlin boot image is shown.
 //
 // We suggest for you to take advantage of this new feature and keep the Marlin
 // boot image unmodified. For an example have a look at the bq Hephestos 2
@ -1000,6 +1000,10 @@
 //                       |________|_________|_________|
 //                           T1        T2        T3
 //
+//   P2: This starts a circular pattern with circle with middle in
+//       NOZZLE_CLEAN_CIRCLE_MIDDLE radius of R and stroke count of S.
+//       Before starting the circle nozzle goes to NOZZLE_CLEAN_START_POINT.
+//
 // Caveats: End point Z should use the same value as Start point Z.
 //
 // Attention: This is an EXPERIMENTAL feature, in the future the G-code arguments
@ -1010,7 +1014,7 @@
 #if ENABLED(NOZZLE_CLEAN_FEATURE)
  // Default number of pattern repetitions
  #define NOZZLE_CLEAN_STROKES  12
-  
+
  // Default number of triangles
  #define NOZZLE_CLEAN_TRIANGLES  3

@ -1018,6 +1022,13 @@
  #define NOZZLE_CLEAN_START_POINT { 30, 30, (Z_MIN_POS + 1)}
  #define NOZZLE_CLEAN_END_POINT   {100, 60, (Z_MIN_POS + 1)}

+  // Circular pattern radius
+  #define NOZZLE_CLEAN_CIRCLE_RADIUS 6.5
+  // Circular pattern circle fragments number
+  #define NOZZLE_CLEAN_CIRCLE_FN 10
+  // Middle point of circle
+  #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT
+
  // Moves the nozzle to the initial position
  #define NOZZLE_CLEAN_GOBACK
 #endif
--- a/Marlin/example_configurations/K8400/Dual-head/Configuration.h
+++ b/Marlin/example_configurations/K8400/Dual-head/Configuration.h
@ -96,7 +96,7 @@
 //
 // Marlin now allow you to have a vendor boot image to be displayed on machine
 // start. When SHOW_CUSTOM_BOOTSCREEN is defined Marlin will first show your
-// custom boot image and them the default Marlin boot image is shown.
+// custom boot image and then the default Marlin boot image is shown.
 //
 // We suggest for you to take advantage of this new feature and keep the Marlin
 // boot image unmodified. For an example have a look at the bq Hephestos 2
@ -1000,6 +1000,10 @@
 //                       |________|_________|_________|
 //                           T1        T2        T3
 //
+//   P2: This starts a circular pattern with circle with middle in
+//       NOZZLE_CLEAN_CIRCLE_MIDDLE radius of R and stroke count of S.
+//       Before starting the circle nozzle goes to NOZZLE_CLEAN_START_POINT.
+//
 // Caveats: End point Z should use the same value as Start point Z.
 //
 // Attention: This is an EXPERIMENTAL feature, in the future the G-code arguments
@ -1010,7 +1014,7 @@
 #if ENABLED(NOZZLE_CLEAN_FEATURE)
  // Default number of pattern repetitions
  #define NOZZLE_CLEAN_STROKES  12
-  
+
  // Default number of triangles
  #define NOZZLE_CLEAN_TRIANGLES  3

@ -1018,6 +1022,13 @@
  #define NOZZLE_CLEAN_START_POINT { 30, 30, (Z_MIN_POS + 1)}
  #define NOZZLE_CLEAN_END_POINT   {100, 60, (Z_MIN_POS + 1)}

+  // Circular pattern radius
+  #define NOZZLE_CLEAN_CIRCLE_RADIUS 6.5
+  // Circular pattern circle fragments number
+  #define NOZZLE_CLEAN_CIRCLE_FN 10
+  // Middle point of circle
+  #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT
+
  // Moves the nozzle to the initial position
  #define NOZZLE_CLEAN_GOBACK
 #endif
--- a/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h
+++ b/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h
@ -96,7 +96,7 @@
 //
 // Marlin now allow you to have a vendor boot image to be displayed on machine
 // start. When SHOW_CUSTOM_BOOTSCREEN is defined Marlin will first show your
-// custom boot image and them the default Marlin boot image is shown.
+// custom boot image and then the default Marlin boot image is shown.
 //
 // We suggest for you to take advantage of this new feature and keep the Marlin
 // boot image unmodified. For an example have a look at the bq Hephestos 2
@ -1000,6 +1000,10 @@
 //                       |________|_________|_________|
 //                           T1        T2        T3
 //
+//   P2: This starts a circular pattern with circle with middle in
+//       NOZZLE_CLEAN_CIRCLE_MIDDLE radius of R and stroke count of S.
+//       Before starting the circle nozzle goes to NOZZLE_CLEAN_START_POINT.
+//
 // Caveats: End point Z should use the same value as Start point Z.
 //
 // Attention: This is an EXPERIMENTAL feature, in the future the G-code arguments
@ -1010,7 +1014,7 @@
 #if ENABLED(NOZZLE_CLEAN_FEATURE)
  // Default number of pattern repetitions
  #define NOZZLE_CLEAN_STROKES  12
-  
+
  // Default number of triangles
  #define NOZZLE_CLEAN_TRIANGLES  3

@ -1018,6 +1022,13 @@
  #define NOZZLE_CLEAN_START_POINT { 30, 30, (Z_MIN_POS + 1)}
  #define NOZZLE_CLEAN_END_POINT   {100, 60, (Z_MIN_POS + 1)}

+  // Circular pattern radius
+  #define NOZZLE_CLEAN_CIRCLE_RADIUS 6.5
+  // Circular pattern circle fragments number
+  #define NOZZLE_CLEAN_CIRCLE_FN 10
+  // Middle point of circle
+  #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT
+
  // Moves the nozzle to the initial position
  #define NOZZLE_CLEAN_GOBACK
 #endif
--- a/Marlin/example_configurations/RigidBot/Configuration.h
+++ b/Marlin/example_configurations/RigidBot/Configuration.h
@ -96,7 +96,7 @@
 //
 // Marlin now allow you to have a vendor boot image to be displayed on machine
 // start. When SHOW_CUSTOM_BOOTSCREEN is defined Marlin will first show your
-// custom boot image and them the default Marlin boot image is shown.
+// custom boot image and then the default Marlin boot image is shown.
 //
 // We suggest for you to take advantage of this new feature and keep the Marlin
 // boot image unmodified. For an example have a look at the bq Hephestos 2
@ -999,6 +999,10 @@
 //                       |________|_________|_________|
 //                           T1        T2        T3
 //
+//   P2: This starts a circular pattern with circle with middle in
+//       NOZZLE_CLEAN_CIRCLE_MIDDLE radius of R and stroke count of S.
+//       Before starting the circle nozzle goes to NOZZLE_CLEAN_START_POINT.
+//
 // Caveats: End point Z should use the same value as Start point Z.
 //
 // Attention: This is an EXPERIMENTAL feature, in the future the G-code arguments
@ -1009,7 +1013,7 @@
 #if ENABLED(NOZZLE_CLEAN_FEATURE)
  // Default number of pattern repetitions
  #define NOZZLE_CLEAN_STROKES  12
-  
+
  // Default number of triangles
  #define NOZZLE_CLEAN_TRIANGLES  3

@ -1017,6 +1021,13 @@
  #define NOZZLE_CLEAN_START_POINT { 30, 30, (Z_MIN_POS + 1)}
  #define NOZZLE_CLEAN_END_POINT   {100, 60, (Z_MIN_POS + 1)}

+  // Circular pattern radius
+  #define NOZZLE_CLEAN_CIRCLE_RADIUS 6.5
+  // Circular pattern circle fragments number
+  #define NOZZLE_CLEAN_CIRCLE_FN 10
+  // Middle point of circle
+  #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT
+
  // Moves the nozzle to the initial position
  #define NOZZLE_CLEAN_GOBACK
 #endif
--- a/Marlin/example_configurations/SCARA/Configuration.h
+++ b/Marlin/example_configurations/SCARA/Configuration.h
@ -128,7 +128,7 @@
 //
 // Marlin now allow you to have a vendor boot image to be displayed on machine
 // start. When SHOW_CUSTOM_BOOTSCREEN is defined Marlin will first show your
-// custom boot image and them the default Marlin boot image is shown.
+// custom boot image and then the default Marlin boot image is shown.
 //
 // We suggest for you to take advantage of this new feature and keep the Marlin
 // boot image unmodified. For an example have a look at the bq Hephestos 2
@ -1015,6 +1015,10 @@
 //                       |________|_________|_________|
 //                           T1        T2        T3
 //
+//   P2: This starts a circular pattern with circle with middle in
+//       NOZZLE_CLEAN_CIRCLE_MIDDLE radius of R and stroke count of S.
+//       Before starting the circle nozzle goes to NOZZLE_CLEAN_START_POINT.
+//
 // Caveats: End point Z should use the same value as Start point Z.
 //
 // Attention: This is an EXPERIMENTAL feature, in the future the G-code arguments
@ -1025,7 +1029,7 @@
 #if ENABLED(NOZZLE_CLEAN_FEATURE)
  // Default number of pattern repetitions
  #define NOZZLE_CLEAN_STROKES  12
-  
+
  // Default number of triangles
  #define NOZZLE_CLEAN_TRIANGLES  3

@ -1033,6 +1037,13 @@
  #define NOZZLE_CLEAN_START_POINT { 30, 30, (Z_MIN_POS + 1)}
  #define NOZZLE_CLEAN_END_POINT   {100, 60, (Z_MIN_POS + 1)}

+  // Circular pattern radius
+  #define NOZZLE_CLEAN_CIRCLE_RADIUS 6.5
+  // Circular pattern circle fragments number
+  #define NOZZLE_CLEAN_CIRCLE_FN 10
+  // Middle point of circle
+  #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT
+
  // Moves the nozzle to the initial position
  #define NOZZLE_CLEAN_GOBACK
 #endif
--- a/Marlin/example_configurations/TAZ4/Configuration.h
+++ b/Marlin/example_configurations/TAZ4/Configuration.h
@ -96,7 +96,7 @@
 //
 // Marlin now allow you to have a vendor boot image to be displayed on machine
 // start. When SHOW_CUSTOM_BOOTSCREEN is defined Marlin will first show your
-// custom boot image and them the default Marlin boot image is shown.
+// custom boot image and then the default Marlin boot image is shown.
 //
 // We suggest for you to take advantage of this new feature and keep the Marlin
 // boot image unmodified. For an example have a look at the bq Hephestos 2
@ -1021,6 +1021,10 @@
 //                       |________|_________|_________|
 //                           T1        T2        T3
 //
+//   P2: This starts a circular pattern with circle with middle in
+//       NOZZLE_CLEAN_CIRCLE_MIDDLE radius of R and stroke count of S.
+//       Before starting the circle nozzle goes to NOZZLE_CLEAN_START_POINT.
+//
 // Caveats: End point Z should use the same value as Start point Z.
 //
 // Attention: This is an EXPERIMENTAL feature, in the future the G-code arguments
@ -1031,7 +1035,7 @@
 #if ENABLED(NOZZLE_CLEAN_FEATURE)
  // Default number of pattern repetitions
  #define NOZZLE_CLEAN_STROKES  12
-  
+
  // Default number of triangles
  #define NOZZLE_CLEAN_TRIANGLES  3

@ -1039,6 +1043,13 @@
  #define NOZZLE_CLEAN_START_POINT { 30, 30, (Z_MIN_POS + 1)}
  #define NOZZLE_CLEAN_END_POINT   {100, 60, (Z_MIN_POS + 1)}

+  // Circular pattern radius
+  #define NOZZLE_CLEAN_CIRCLE_RADIUS 6.5
+  // Circular pattern circle fragments number
+  #define NOZZLE_CLEAN_CIRCLE_FN 10
+  // Middle point of circle
+  #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT
+
  // Moves the nozzle to the initial position
  #define NOZZLE_CLEAN_GOBACK
 #endif
--- a/Marlin/example_configurations/WITBOX/Configuration.h
+++ b/Marlin/example_configurations/WITBOX/Configuration.h
@ -96,7 +96,7 @@
 //
 // Marlin now allow you to have a vendor boot image to be displayed on machine
 // start. When SHOW_CUSTOM_BOOTSCREEN is defined Marlin will first show your
-// custom boot image and them the default Marlin boot image is shown.
+// custom boot image and then the default Marlin boot image is shown.
 //
 // We suggest for you to take advantage of this new feature and keep the Marlin
 // boot image unmodified. For an example have a look at the bq Hephestos 2
@ -992,6 +992,10 @@
 //                       |________|_________|_________|
 //                           T1        T2        T3
 //
+//   P2: This starts a circular pattern with circle with middle in
+//       NOZZLE_CLEAN_CIRCLE_MIDDLE radius of R and stroke count of S.
+//       Before starting the circle nozzle goes to NOZZLE_CLEAN_START_POINT.
+//
 // Caveats: End point Z should use the same value as Start point Z.
 //
 // Attention: This is an EXPERIMENTAL feature, in the future the G-code arguments
@ -1002,7 +1006,7 @@
 #if ENABLED(NOZZLE_CLEAN_FEATURE)
  // Default number of pattern repetitions
  #define NOZZLE_CLEAN_STROKES  12
-  
+
  // Default number of triangles
  #define NOZZLE_CLEAN_TRIANGLES  3

@ -1010,6 +1014,13 @@
  #define NOZZLE_CLEAN_START_POINT { 30, 30, (Z_MIN_POS + 1)}
  #define NOZZLE_CLEAN_END_POINT   {100, 60, (Z_MIN_POS + 1)}

+  // Circular pattern radius
+  #define NOZZLE_CLEAN_CIRCLE_RADIUS 6.5
+  // Circular pattern circle fragments number
+  #define NOZZLE_CLEAN_CIRCLE_FN 10
+  // Middle point of circle
+  #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT
+
  // Moves the nozzle to the initial position
  #define NOZZLE_CLEAN_GOBACK
 #endif
--- a/Marlin/example_configurations/adafruit/ST7565/Configuration.h
+++ b/Marlin/example_configurations/adafruit/ST7565/Configuration.h
@ -96,7 +96,7 @@
 //
 // Marlin now allow you to have a vendor boot image to be displayed on machine
 // start. When SHOW_CUSTOM_BOOTSCREEN is defined Marlin will first show your
-// custom boot image and them the default Marlin boot image is shown.
+// custom boot image and then the default Marlin boot image is shown.
 //
 // We suggest for you to take advantage of this new feature and keep the Marlin
 // boot image unmodified. For an example have a look at the bq Hephestos 2
@ -1000,6 +1000,10 @@
 //                       |________|_________|_________|
 //                           T1        T2        T3
 //
+//   P2: This starts a circular pattern with circle with middle in
+//       NOZZLE_CLEAN_CIRCLE_MIDDLE radius of R and stroke count of S.
+//       Before starting the circle nozzle goes to NOZZLE_CLEAN_START_POINT.
+//
 // Caveats: End point Z should use the same value as Start point Z.
 //
 // Attention: This is an EXPERIMENTAL feature, in the future the G-code arguments
@ -1010,7 +1014,7 @@
 #if ENABLED(NOZZLE_CLEAN_FEATURE)
  // Default number of pattern repetitions
  #define NOZZLE_CLEAN_STROKES  12
-  
+
  // Default number of triangles
  #define NOZZLE_CLEAN_TRIANGLES  3

@ -1018,6 +1022,13 @@
  #define NOZZLE_CLEAN_START_POINT { 30, 30, (Z_MIN_POS + 1)}
  #define NOZZLE_CLEAN_END_POINT   {100, 60, (Z_MIN_POS + 1)}

+  // Circular pattern radius
+  #define NOZZLE_CLEAN_CIRCLE_RADIUS 6.5
+  // Circular pattern circle fragments number
+  #define NOZZLE_CLEAN_CIRCLE_FN 10
+  // Middle point of circle
+  #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT
+
  // Moves the nozzle to the initial position
  #define NOZZLE_CLEAN_GOBACK
 #endif
--- a/Marlin/example_configurations/delta/generic/Configuration.h
+++ b/Marlin/example_configurations/delta/generic/Configuration.h
@ -96,7 +96,7 @@
 //
 // Marlin now allow you to have a vendor boot image to be displayed on machine
 // start. When SHOW_CUSTOM_BOOTSCREEN is defined Marlin will first show your
-// custom boot image and them the default Marlin boot image is shown.
+// custom boot image and then the default Marlin boot image is shown.
 //
 // We suggest for you to take advantage of this new feature and keep the Marlin
 // boot image unmodified. For an example have a look at the bq Hephestos 2
@ -1087,6 +1087,10 @@
 //                       |________|_________|_________|
 //                           T1        T2        T3
 //
+//   P2: This starts a circular pattern with circle with middle in
+//       NOZZLE_CLEAN_CIRCLE_MIDDLE radius of R and stroke count of S.
+//       Before starting the circle nozzle goes to NOZZLE_CLEAN_START_POINT.
+//
 // Caveats: End point Z should use the same value as Start point Z.
 //
 // Attention: This is an EXPERIMENTAL feature, in the future the G-code arguments
@ -1097,7 +1101,7 @@
 #if ENABLED(NOZZLE_CLEAN_FEATURE)
  // Default number of pattern repetitions
  #define NOZZLE_CLEAN_STROKES  12
-  
+
  // Default number of triangles
  #define NOZZLE_CLEAN_TRIANGLES  3

@ -1105,6 +1109,13 @@
  #define NOZZLE_CLEAN_START_POINT { 30, 30, (Z_MIN_POS + 1)}
  #define NOZZLE_CLEAN_END_POINT   {100, 60, (Z_MIN_POS + 1)}

+  // Circular pattern radius
+  #define NOZZLE_CLEAN_CIRCLE_RADIUS 6.5
+  // Circular pattern circle fragments number
+  #define NOZZLE_CLEAN_CIRCLE_FN 10
+  // Middle point of circle
+  #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT
+
  // Moves the nozzle to the initial position
  #define NOZZLE_CLEAN_GOBACK
 #endif
--- a/Marlin/example_configurations/delta/kossel_mini/Configuration.h
+++ b/Marlin/example_configurations/delta/kossel_mini/Configuration.h
@ -96,7 +96,7 @@
 //
 // Marlin now allow you to have a vendor boot image to be displayed on machine
 // start. When SHOW_CUSTOM_BOOTSCREEN is defined Marlin will first show your
-// custom boot image and them the default Marlin boot image is shown.
+// custom boot image and then the default Marlin boot image is shown.
 //
 // We suggest for you to take advantage of this new feature and keep the Marlin
 // boot image unmodified. For an example have a look at the bq Hephestos 2
@ -1090,6 +1090,10 @@
 //                       |________|_________|_________|
 //                           T1        T2        T3
 //
+//   P2: This starts a circular pattern with circle with middle in
+//       NOZZLE_CLEAN_CIRCLE_MIDDLE radius of R and stroke count of S.
+//       Before starting the circle nozzle goes to NOZZLE_CLEAN_START_POINT.
+//
 // Caveats: End point Z should use the same value as Start point Z.
 //
 // Attention: This is an EXPERIMENTAL feature, in the future the G-code arguments
@ -1100,7 +1104,7 @@
 #if ENABLED(NOZZLE_CLEAN_FEATURE)
  // Default number of pattern repetitions
  #define NOZZLE_CLEAN_STROKES  12
-  
+
  // Default number of triangles
  #define NOZZLE_CLEAN_TRIANGLES  3

@ -1108,6 +1112,13 @@
  #define NOZZLE_CLEAN_START_POINT { 30, 30, (Z_MIN_POS + 1)}
  #define NOZZLE_CLEAN_END_POINT   {100, 60, (Z_MIN_POS + 1)}

+  // Circular pattern radius
+  #define NOZZLE_CLEAN_CIRCLE_RADIUS 6.5
+  // Circular pattern circle fragments number
+  #define NOZZLE_CLEAN_CIRCLE_FN 10
+  // Middle point of circle
+  #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT
+
  // Moves the nozzle to the initial position
  #define NOZZLE_CLEAN_GOBACK
 #endif
--- a/Marlin/example_configurations/delta/kossel_pro/Configuration.h
+++ b/Marlin/example_configurations/delta/kossel_pro/Configuration.h
@ -100,7 +100,7 @@
 //
 // Marlin now allow you to have a vendor boot image to be displayed on machine
 // start. When SHOW_CUSTOM_BOOTSCREEN is defined Marlin will first show your
-// custom boot image and them the default Marlin boot image is shown.
+// custom boot image and then the default Marlin boot image is shown.
 //
 // We suggest for you to take advantage of this new feature and keep the Marlin
 // boot image unmodified. For an example have a look at the bq Hephestos 2
@ -1089,6 +1089,10 @@
 //                       |________|_________|_________|
 //                           T1        T2        T3
 //
+//   P2: This starts a circular pattern with circle with middle in
+//       NOZZLE_CLEAN_CIRCLE_MIDDLE radius of R and stroke count of S.
+//       Before starting the circle nozzle goes to NOZZLE_CLEAN_START_POINT.
+//
 // Caveats: End point Z should use the same value as Start point Z.
 //
 // Attention: This is an EXPERIMENTAL feature, in the future the G-code arguments
@ -1099,7 +1103,7 @@
 #if ENABLED(NOZZLE_CLEAN_FEATURE)
  // Default number of pattern repetitions
  #define NOZZLE_CLEAN_STROKES  12
-  
+
  // Default number of triangles
  #define NOZZLE_CLEAN_TRIANGLES  3

@ -1107,6 +1111,13 @@
  #define NOZZLE_CLEAN_START_POINT { 30, 30, (Z_MIN_POS + 1)}
  #define NOZZLE_CLEAN_END_POINT   {100, 60, (Z_MIN_POS + 1)}

+  // Circular pattern radius
+  #define NOZZLE_CLEAN_CIRCLE_RADIUS 6.5
+  // Circular pattern circle fragments number
+  #define NOZZLE_CLEAN_CIRCLE_FN 10
+  // Middle point of circle
+  #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT
+
  // Moves the nozzle to the initial position
  #define NOZZLE_CLEAN_GOBACK
 #endif
--- a/Marlin/example_configurations/delta/kossel_xl/Configuration.h
+++ b/Marlin/example_configurations/delta/kossel_xl/Configuration.h
@ -89,7 +89,7 @@
 //
 // Marlin now allow you to have a vendor boot image to be displayed on machine
 // start. When SHOW_CUSTOM_BOOTSCREEN is defined Marlin will first show your
-// custom boot image and them the default Marlin boot image is shown.
+// custom boot image and then the default Marlin boot image is shown.
 //
 // We suggest for you to take advantage of this new feature and keep the Marlin
 // boot image unmodified. For an example have a look at the bq Hephestos 2
@ -1093,6 +1093,10 @@
 //                       |________|_________|_________|
 //                           T1        T2        T3
 //
+//   P2: This starts a circular pattern with circle with middle in
+//       NOZZLE_CLEAN_CIRCLE_MIDDLE radius of R and stroke count of S.
+//       Before starting the circle nozzle goes to NOZZLE_CLEAN_START_POINT.
+//
 // Caveats: End point Z should use the same value as Start point Z.
 //
 // Attention: This is an EXPERIMENTAL feature, in the future the G-code arguments
@ -1103,7 +1107,7 @@
 #if ENABLED(NOZZLE_CLEAN_FEATURE)
  // Default number of pattern repetitions
  #define NOZZLE_CLEAN_STROKES  12
-  
+
  // Default number of triangles
  #define NOZZLE_CLEAN_TRIANGLES  3

@ -1111,6 +1115,13 @@
  #define NOZZLE_CLEAN_START_POINT { 30, 30, (Z_MIN_POS + 1)}
  #define NOZZLE_CLEAN_END_POINT   {100, 60, (Z_MIN_POS + 1)}

+  // Circular pattern radius
+  #define NOZZLE_CLEAN_CIRCLE_RADIUS 6.5
+  // Circular pattern circle fragments number
+  #define NOZZLE_CLEAN_CIRCLE_FN 10
+  // Middle point of circle
+  #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT
+
  // Moves the nozzle to the initial position
  #define NOZZLE_CLEAN_GOBACK
 #endif
--- a/Marlin/example_configurations/makibox/Configuration.h
+++ b/Marlin/example_configurations/makibox/Configuration.h
@ -96,7 +96,7 @@
 //
 // Marlin now allow you to have a vendor boot image to be displayed on machine
 // start. When SHOW_CUSTOM_BOOTSCREEN is defined Marlin will first show your
-// custom boot image and them the default Marlin boot image is shown.
+// custom boot image and then the default Marlin boot image is shown.
 //
 // We suggest for you to take advantage of this new feature and keep the Marlin
 // boot image unmodified. For an example have a look at the bq Hephestos 2
@ -1003,6 +1003,10 @@
 //                       |________|_________|_________|
 //                           T1        T2        T3
 //
+//   P2: This starts a circular pattern with circle with middle in
+//       NOZZLE_CLEAN_CIRCLE_MIDDLE radius of R and stroke count of S.
+//       Before starting the circle nozzle goes to NOZZLE_CLEAN_START_POINT.
+//
 // Caveats: End point Z should use the same value as Start point Z.
 //
 // Attention: This is an EXPERIMENTAL feature, in the future the G-code arguments
@ -1013,7 +1017,7 @@
 #if ENABLED(NOZZLE_CLEAN_FEATURE)
  // Default number of pattern repetitions
  #define NOZZLE_CLEAN_STROKES  12
-  
+
  // Default number of triangles
  #define NOZZLE_CLEAN_TRIANGLES  3

@ -1021,6 +1025,13 @@
  #define NOZZLE_CLEAN_START_POINT { 30, 30, (Z_MIN_POS + 1)}
  #define NOZZLE_CLEAN_END_POINT   {100, 60, (Z_MIN_POS + 1)}

+  // Circular pattern radius
+  #define NOZZLE_CLEAN_CIRCLE_RADIUS 6.5
+  // Circular pattern circle fragments number
+  #define NOZZLE_CLEAN_CIRCLE_FN 10
+  // Middle point of circle
+  #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT
+
  // Moves the nozzle to the initial position
  #define NOZZLE_CLEAN_GOBACK
 #endif
--- a/Marlin/example_configurations/tvrrug/Round2/Configuration.h
+++ b/Marlin/example_configurations/tvrrug/Round2/Configuration.h
@ -96,7 +96,7 @@
 //
 // Marlin now allow you to have a vendor boot image to be displayed on machine
 // start. When SHOW_CUSTOM_BOOTSCREEN is defined Marlin will first show your
-// custom boot image and them the default Marlin boot image is shown.
+// custom boot image and then the default Marlin boot image is shown.
 //
 // We suggest for you to take advantage of this new feature and keep the Marlin
 // boot image unmodified. For an example have a look at the bq Hephestos 2
@ -996,6 +996,10 @@
 //                       |________|_________|_________|
 //                           T1        T2        T3
 //
+//   P2: This starts a circular pattern with circle with middle in
+//       NOZZLE_CLEAN_CIRCLE_MIDDLE radius of R and stroke count of S.
+//       Before starting the circle nozzle goes to NOZZLE_CLEAN_START_POINT.
+//
 // Caveats: End point Z should use the same value as Start point Z.
 //
 // Attention: This is an EXPERIMENTAL feature, in the future the G-code arguments
@ -1006,7 +1010,7 @@
 #if ENABLED(NOZZLE_CLEAN_FEATURE)
  // Default number of pattern repetitions
  #define NOZZLE_CLEAN_STROKES  12
-  
+
  // Default number of triangles
  #define NOZZLE_CLEAN_TRIANGLES  3

@ -1014,6 +1018,13 @@
  #define NOZZLE_CLEAN_START_POINT { 30, 30, (Z_MIN_POS + 1)}
  #define NOZZLE_CLEAN_END_POINT   {100, 60, (Z_MIN_POS + 1)}

+  // Circular pattern radius
+  #define NOZZLE_CLEAN_CIRCLE_RADIUS 6.5
+  // Circular pattern circle fragments number
+  #define NOZZLE_CLEAN_CIRCLE_FN 10
+  // Middle point of circle
+  #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT
+
  // Moves the nozzle to the initial position
  #define NOZZLE_CLEAN_GOBACK
 #endif