Browse Source

Merge pull request #11841 from thinkyhead/bf2_radds_ext_board_v3

Support for RADDS Extension Board V3 (and 6 extruders)
pull/1/head
Scott Lahteine 6 years ago
committed by GitHub
parent
commit
722d186ca0
No known key found for this signature in database GPG Key ID: 4AEE18F83AFDEB23
  1. 11
      Marlin/Configuration.h
  2. 15
      Marlin/Configuration_adv.h
  3. 2
      Marlin/src/HAL/HAL_AVR/SanityCheck.h
  4. 2
      Marlin/src/HAL/HAL_STM32F7/SanityCheck.h
  5. 13
      Marlin/src/Marlin.cpp
  6. 15
      Marlin/src/Marlin.h
  7. 11
      Marlin/src/config/default/Configuration.h
  8. 15
      Marlin/src/config/default/Configuration_adv.h
  9. 11
      Marlin/src/config/examples/AlephObjects/TAZ4/Configuration.h
  10. 15
      Marlin/src/config/examples/AlephObjects/TAZ4/Configuration_adv.h
  11. 11
      Marlin/src/config/examples/AliExpress/CL-260/Configuration.h
  12. 11
      Marlin/src/config/examples/Anet/A2/Configuration.h
  13. 15
      Marlin/src/config/examples/Anet/A2/Configuration_adv.h
  14. 11
      Marlin/src/config/examples/Anet/A2plus/Configuration.h
  15. 15
      Marlin/src/config/examples/Anet/A2plus/Configuration_adv.h
  16. 11
      Marlin/src/config/examples/Anet/A6/Configuration.h
  17. 15
      Marlin/src/config/examples/Anet/A6/Configuration_adv.h
  18. 11
      Marlin/src/config/examples/Anet/A8/Configuration.h
  19. 15
      Marlin/src/config/examples/Anet/A8/Configuration_adv.h
  20. 11
      Marlin/src/config/examples/Azteeg/X5GT/Configuration.h
  21. 15
      Marlin/src/config/examples/Azteeg/X5GT/Configuration_adv.h
  22. 10
      Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration.h
  23. 15
      Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h
  24. 10
      Marlin/src/config/examples/BIBO/TouchX/default/Configuration.h
  25. 15
      Marlin/src/config/examples/BIBO/TouchX/default/Configuration_adv.h
  26. 11
      Marlin/src/config/examples/BQ/Hephestos/Configuration.h
  27. 15
      Marlin/src/config/examples/BQ/Hephestos/Configuration_adv.h
  28. 11
      Marlin/src/config/examples/BQ/Hephestos_2/Configuration.h
  29. 15
      Marlin/src/config/examples/BQ/Hephestos_2/Configuration_adv.h
  30. 11
      Marlin/src/config/examples/BQ/WITBOX/Configuration.h
  31. 15
      Marlin/src/config/examples/BQ/WITBOX/Configuration_adv.h
  32. 11
      Marlin/src/config/examples/Cartesio/Configuration.h
  33. 15
      Marlin/src/config/examples/Cartesio/Configuration_adv.h
  34. 11
      Marlin/src/config/examples/Creality/CR-10/Configuration.h
  35. 15
      Marlin/src/config/examples/Creality/CR-10/Configuration_adv.h
  36. 11
      Marlin/src/config/examples/Creality/CR-10S/Configuration.h
  37. 15
      Marlin/src/config/examples/Creality/CR-10S/Configuration_adv.h
  38. 11
      Marlin/src/config/examples/Creality/CR-10mini/Configuration.h
  39. 15
      Marlin/src/config/examples/Creality/CR-10mini/Configuration_adv.h
  40. 11
      Marlin/src/config/examples/Creality/CR-8/Configuration.h
  41. 15
      Marlin/src/config/examples/Creality/CR-8/Configuration_adv.h
  42. 11
      Marlin/src/config/examples/Creality/Ender-2/Configuration.h
  43. 15
      Marlin/src/config/examples/Creality/Ender-2/Configuration_adv.h
  44. 11
      Marlin/src/config/examples/Creality/Ender-3/Configuration.h
  45. 15
      Marlin/src/config/examples/Creality/Ender-3/Configuration_adv.h
  46. 11
      Marlin/src/config/examples/Creality/Ender-4/Configuration.h
  47. 15
      Marlin/src/config/examples/Creality/Ender-4/Configuration_adv.h
  48. 11
      Marlin/src/config/examples/Einstart-S/Configuration.h
  49. 15
      Marlin/src/config/examples/Einstart-S/Configuration_adv.h
  50. 11
      Marlin/src/config/examples/Felix/Configuration.h
  51. 15
      Marlin/src/config/examples/Felix/Configuration_adv.h
  52. 11
      Marlin/src/config/examples/Felix/DUAL/Configuration.h
  53. 11
      Marlin/src/config/examples/FolgerTech/i3-2020/Configuration.h
  54. 15
      Marlin/src/config/examples/FolgerTech/i3-2020/Configuration_adv.h
  55. 11
      Marlin/src/config/examples/Formbot/T-Rex_2+/Configuration.h
  56. 15
      Marlin/src/config/examples/Formbot/T-Rex_2+/Configuration_adv.h
  57. 11
      Marlin/src/config/examples/Formbot/T_Rex_3/Configuration.h
  58. 15
      Marlin/src/config/examples/Formbot/T_Rex_3/Configuration_adv.h
  59. 11
      Marlin/src/config/examples/Geeetech/GT2560/Configuration.h
  60. 11
      Marlin/src/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h
  61. 11
      Marlin/src/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h
  62. 11
      Marlin/src/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h
  63. 11
      Marlin/src/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h
  64. 15
      Marlin/src/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h
  65. 11
      Marlin/src/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h
  66. 15
      Marlin/src/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h
  67. 11
      Marlin/src/config/examples/Infitary/i3-M508/Configuration.h
  68. 15
      Marlin/src/config/examples/Infitary/i3-M508/Configuration_adv.h
  69. 11
      Marlin/src/config/examples/JGAurora/A5/Configuration.h
  70. 15
      Marlin/src/config/examples/JGAurora/A5/Configuration_adv.h
  71. 11
      Marlin/src/config/examples/MakerParts/Configuration.h
  72. 15
      Marlin/src/config/examples/MakerParts/Configuration_adv.h
  73. 10
      Marlin/src/config/examples/Malyan/M150/Configuration.h
  74. 15
      Marlin/src/config/examples/Malyan/M150/Configuration_adv.h
  75. 11
      Marlin/src/config/examples/Malyan/M200/Configuration.h
  76. 15
      Marlin/src/config/examples/Malyan/M200/Configuration_adv.h
  77. 11
      Marlin/src/config/examples/Micromake/C1/basic/Configuration.h
  78. 11
      Marlin/src/config/examples/Micromake/C1/enhanced/Configuration.h
  79. 15
      Marlin/src/config/examples/Micromake/C1/enhanced/Configuration_adv.h
  80. 11
      Marlin/src/config/examples/Mks/Sbase/Configuration.h
  81. 15
      Marlin/src/config/examples/Mks/Sbase/Configuration_adv.h
  82. 11
      Marlin/src/config/examples/RepRapPro/Huxley/Configuration.h
  83. 11
      Marlin/src/config/examples/RepRapWorld/Megatronics/Configuration.h
  84. 11
      Marlin/src/config/examples/RigidBot/Configuration.h
  85. 15
      Marlin/src/config/examples/RigidBot/Configuration_adv.h
  86. 11
      Marlin/src/config/examples/SCARA/Configuration.h
  87. 15
      Marlin/src/config/examples/SCARA/Configuration_adv.h
  88. 11
      Marlin/src/config/examples/STM32F10/Configuration.h
  89. 11
      Marlin/src/config/examples/STM32F4/Configuration.h
  90. 11
      Marlin/src/config/examples/Sanguinololu/Configuration.h
  91. 15
      Marlin/src/config/examples/Sanguinololu/Configuration_adv.h
  92. 11
      Marlin/src/config/examples/TheBorg/Configuration.h
  93. 15
      Marlin/src/config/examples/TheBorg/Configuration_adv.h
  94. 11
      Marlin/src/config/examples/TinyBoy2/Configuration.h
  95. 15
      Marlin/src/config/examples/TinyBoy2/Configuration_adv.h
  96. 11
      Marlin/src/config/examples/Tronxy/X1/Configuration.h
  97. 11
      Marlin/src/config/examples/Tronxy/X3A/Configuration.h
  98. 15
      Marlin/src/config/examples/Tronxy/X3A/Configuration_adv.h
  99. 11
      Marlin/src/config/examples/Tronxy/X5S/Configuration.h
  100. 11
      Marlin/src/config/examples/Tronxy/XY100/Configuration.h

11
Marlin/Configuration.h

@ -333,6 +333,7 @@
#define TEMP_SENSOR_2 0
#define TEMP_SENSOR_3 0
#define TEMP_SENSOR_4 0
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 0
#define TEMP_SENSOR_CHAMBER 0
@ -363,6 +364,7 @@
#define HEATER_2_MINTEMP 5
#define HEATER_3_MINTEMP 5
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off.
@ -373,6 +375,7 @@
#define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
//===========================================================================
@ -593,6 +596,7 @@
//#define E2_DRIVER_TYPE A4988
//#define E3_DRIVER_TYPE A4988
//#define E4_DRIVER_TYPE A4988
//#define E5_DRIVER_TYPE A4988
// Enable this feature if all enabled endstop pins are interrupt-capable.
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
@ -638,14 +642,14 @@
/**
* Default Axis Steps Per Unit (steps/mm)
* Override with M92
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 4000, 500 }
/**
* Default Max Feed Rate (mm/s)
* Override with M203
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_FEEDRATE { 300, 300, 5, 25 }
@ -653,7 +657,7 @@
* Default Max Acceleration (change/s) change = mm/s
* (Maximum start speed for accelerated moves)
* Override with M201
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_ACCELERATION { 3000, 3000, 100, 10000 }
@ -892,6 +896,7 @@
#define INVERT_E2_DIR false
#define INVERT_E3_DIR false
#define INVERT_E4_DIR false
#define INVERT_E5_DIR false
// @section homing

15
Marlin/Configuration_adv.h

@ -242,6 +242,7 @@
#define E2_AUTO_FAN_PIN -1
#define E3_AUTO_FAN_PIN -1
#define E4_AUTO_FAN_PIN -1
#define E5_AUTO_FAN_PIN -1
#define CHAMBER_AUTO_FAN_PIN -1
#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed
@ -482,7 +483,7 @@
//#define ADAPTIVE_STEP_SMOOTHING
// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU.
#define MICROSTEP_MODES { 16, 16, 16, 16, 16 } // [1,2,4,8,16]
#define MICROSTEP_MODES { 16, 16, 16, 16, 16, 16 } // [1,2,4,8,16]
/**
* @section stepper motor current
@ -1122,6 +1123,10 @@
#define E4_SENSE_RESISTOR 91
#define E4_MICROSTEPS 16
#define E5_MAX_CURRENT 1000
#define E5_SENSE_RESISTOR 91
#define E5_MICROSTEPS 16
#endif // TMC26X
// @section tmc_smart
@ -1186,6 +1191,9 @@
#define E4_CURRENT 800
#define E4_MICROSTEPS 16
#define E5_CURRENT 800
#define E5_MICROSTEPS 16
/**
* Use software SPI for TMC2130.
* The default SW SPI pins are defined the respective pins files,
@ -1241,6 +1249,7 @@
#define E2_HYBRID_THRESHOLD 30
#define E3_HYBRID_THRESHOLD 30
#define E4_HYBRID_THRESHOLD 30
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
@ -1358,6 +1367,10 @@
#define E4_OVERCURRENT 2000
#define E4_STALLCURRENT 1500
#define E5_MICROSTEPS 16
#define E5_OVERCURRENT 2000
#define E5_STALLCURRENT 1500
#endif // L6470
/**

2
Marlin/src/HAL/HAL_AVR/SanityCheck.h

@ -78,6 +78,8 @@
#error "SPINDLE_LASER_PWM_PIN is used by E3_AUTO_FAN_PIN."
#elif PIN_EXISTS(E4_AUTO_FAN) && SPINDLE_LASER_PWM_PIN == E4_AUTO_FAN_PIN
#error "SPINDLE_LASER_PWM_PIN is used by E4_AUTO_FAN_PIN."
#elif PIN_EXISTS(E5_AUTO_FAN) && SPINDLE_LASER_PWM_PIN == E5_AUTO_FAN_PIN
#error "SPINDLE_LASER_PWM_PIN is used by E5_AUTO_FAN_PIN."
#elif PIN_EXISTS(FAN) && SPINDLE_LASER_PWM_PIN == FAN_PIN
#error "SPINDLE_LASER_PWM_PIN is used FAN_PIN."
#elif PIN_EXISTS(FAN1) && SPINDLE_LASER_PWM_PIN == FAN1_PIN

2
Marlin/src/HAL/HAL_STM32F7/SanityCheck.h

@ -53,6 +53,8 @@
#error "SPINDLE_LASER_PWM_PIN is used by E3_AUTO_FAN_PIN."
#elif PIN_EXISTS(E4_AUTO_FAN) && SPINDLE_LASER_PWM_PIN == E4_AUTO_FAN_PIN
#error "SPINDLE_LASER_PWM_PIN is used by E4_AUTO_FAN_PIN."
#elif PIN_EXISTS(E5_AUTO_FAN) && SPINDLE_LASER_PWM_PIN == E5_AUTO_FAN_PIN
#error "SPINDLE_LASER_PWM_PIN is used by E5_AUTO_FAN_PIN."
#elif PIN_EXISTS(FAN) && SPINDLE_LASER_PWM_PIN == FAN_PIN
#error "SPINDLE_LASER_PWM_PIN is used FAN_PIN."
#elif PIN_EXISTS(FAN1) && SPINDLE_LASER_PWM_PIN == FAN1_PIN

13
Marlin/src/Marlin.cpp

@ -290,6 +290,7 @@ void enable_all_steppers() {
enable_E2();
enable_E3();
enable_E4();
enable_E5();
}
void disable_e_steppers() {
@ -298,6 +299,7 @@ void disable_e_steppers() {
disable_E2();
disable_E3();
disable_E4();
disable_E5();
}
void disable_e_stepper(const uint8_t e) {
@ -307,6 +309,7 @@ void disable_e_stepper(const uint8_t e) {
case 2: disable_E2(); break;
case 3: disable_E3(); break;
case 4: disable_E4(); break;
case 5: disable_E5(); break;
}
}
@ -440,7 +443,7 @@ void manage_inactivity(const bool ignore_stepper_queue/*=false*/) {
#if E_STEPPERS > 1
case 2: case 3: oldstatus = E1_ENABLE_READ; enable_E1(); break;
#if E_STEPPERS > 2
case 4: oldstatus = E2_ENABLE_READ; enable_E2(); break;
case 4: case 5: oldstatus = E2_ENABLE_READ; enable_E2(); break;
#endif // E_STEPPERS > 2
#endif // E_STEPPERS > 1
}
@ -456,6 +459,9 @@ void manage_inactivity(const bool ignore_stepper_queue/*=false*/) {
case 3: oldstatus = E3_ENABLE_READ; enable_E3(); break;
#if E_STEPPERS > 4
case 4: oldstatus = E4_ENABLE_READ; enable_E4(); break;
#if E_STEPPERS > 5
case 5: oldstatus = E5_ENABLE_READ; enable_E5(); break;
#endif // E_STEPPERS > 5
#endif // E_STEPPERS > 4
#endif // E_STEPPERS > 3
#endif // E_STEPPERS > 2
@ -476,7 +482,7 @@ void manage_inactivity(const bool ignore_stepper_queue/*=false*/) {
#if E_STEPPERS > 1
case 2: case 3: oldstatus = E1_ENABLE_WRITE(oldstatus); break;
#if E_STEPPERS > 2
case 4: oldstatus = E2_ENABLE_WRITE(oldstatus); break;
case 4: case 5: oldstatus = E2_ENABLE_WRITE(oldstatus); break;
#endif // E_STEPPERS > 2
#endif // E_STEPPERS > 1
}
@ -491,6 +497,9 @@ void manage_inactivity(const bool ignore_stepper_queue/*=false*/) {
case 3: E3_ENABLE_WRITE(oldstatus); break;
#if E_STEPPERS > 4
case 4: E4_ENABLE_WRITE(oldstatus); break;
#if E_STEPPERS > 5
case 5: E5_ENABLE_WRITE(oldstatus); break;
#endif // E_STEPPERS > 5
#endif // E_STEPPERS > 4
#endif // E_STEPPERS > 3
#endif // E_STEPPERS > 2

15
Marlin/src/Marlin.h

@ -83,7 +83,10 @@ void manage_inactivity(const bool ignore_stepper_queue=false);
/**
* Mixing steppers synchronize their enable (and direction) together
*/
#if MIXING_STEPPERS > 4
#if MIXING_STEPPERS > 5
#define enable_E0() { E0_ENABLE_WRITE( E_ENABLE_ON); E1_ENABLE_WRITE( E_ENABLE_ON); E2_ENABLE_WRITE( E_ENABLE_ON); E3_ENABLE_WRITE( E_ENABLE_ON); E4_ENABLE_WRITE( E_ENABLE_ON); E5_ENABLE_WRITE( E_ENABLE_ON); }
#define disable_E0() { E0_ENABLE_WRITE(!E_ENABLE_ON); E1_ENABLE_WRITE(!E_ENABLE_ON); E2_ENABLE_WRITE(!E_ENABLE_ON); E3_ENABLE_WRITE(!E_ENABLE_ON); E4_ENABLE_WRITE(!E_ENABLE_ON); E5_ENABLE_WRITE(!E_ENABLE_ON); }
#elif MIXING_STEPPERS > 4
#define enable_E0() { E0_ENABLE_WRITE( E_ENABLE_ON); E1_ENABLE_WRITE( E_ENABLE_ON); E2_ENABLE_WRITE( E_ENABLE_ON); E3_ENABLE_WRITE( E_ENABLE_ON); E4_ENABLE_WRITE( E_ENABLE_ON); }
#define disable_E0() { E0_ENABLE_WRITE(!E_ENABLE_ON); E1_ENABLE_WRITE(!E_ENABLE_ON); E2_ENABLE_WRITE(!E_ENABLE_ON); E3_ENABLE_WRITE(!E_ENABLE_ON); E4_ENABLE_WRITE(!E_ENABLE_ON); }
#elif MIXING_STEPPERS > 3
@ -104,6 +107,8 @@ void manage_inactivity(const bool ignore_stepper_queue=false);
#define disable_E3() NOOP
#define enable_E4() NOOP
#define disable_E4() NOOP
#define enable_E5() NOOP
#define disable_E5() NOOP
#else // !MIXING_EXTRUDER
@ -147,6 +152,14 @@ void manage_inactivity(const bool ignore_stepper_queue=false);
#define disable_E4() NOOP
#endif
#if E_STEPPERS > 5 && HAS_E5_ENABLE
#define enable_E5() E5_ENABLE_WRITE( E_ENABLE_ON)
#define disable_E5() E5_ENABLE_WRITE(!E_ENABLE_ON)
#else
#define enable_E5() NOOP
#define disable_E5() NOOP
#endif
#endif // !MIXING_EXTRUDER
#if ENABLED(EXPERIMENTAL_I2CBUS)

11
Marlin/src/config/default/Configuration.h

@ -333,6 +333,7 @@
#define TEMP_SENSOR_2 0
#define TEMP_SENSOR_3 0
#define TEMP_SENSOR_4 0
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 0
#define TEMP_SENSOR_CHAMBER 0
@ -363,6 +364,7 @@
#define HEATER_2_MINTEMP 5
#define HEATER_3_MINTEMP 5
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off.
@ -373,6 +375,7 @@
#define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
//===========================================================================
@ -593,6 +596,7 @@
//#define E2_DRIVER_TYPE A4988
//#define E3_DRIVER_TYPE A4988
//#define E4_DRIVER_TYPE A4988
//#define E5_DRIVER_TYPE A4988
// Enable this feature if all enabled endstop pins are interrupt-capable.
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
@ -638,14 +642,14 @@
/**
* Default Axis Steps Per Unit (steps/mm)
* Override with M92
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 4000, 500 }
/**
* Default Max Feed Rate (mm/s)
* Override with M203
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_FEEDRATE { 300, 300, 5, 25 }
@ -653,7 +657,7 @@
* Default Max Acceleration (change/s) change = mm/s
* (Maximum start speed for accelerated moves)
* Override with M201
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_ACCELERATION { 3000, 3000, 100, 10000 }
@ -892,6 +896,7 @@
#define INVERT_E2_DIR false
#define INVERT_E3_DIR false
#define INVERT_E4_DIR false
#define INVERT_E5_DIR false
// @section homing

15
Marlin/src/config/default/Configuration_adv.h

@ -242,6 +242,7 @@
#define E2_AUTO_FAN_PIN -1
#define E3_AUTO_FAN_PIN -1
#define E4_AUTO_FAN_PIN -1
#define E5_AUTO_FAN_PIN -1
#define CHAMBER_AUTO_FAN_PIN -1
#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed
@ -482,7 +483,7 @@
//#define ADAPTIVE_STEP_SMOOTHING
// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU.
#define MICROSTEP_MODES { 16, 16, 16, 16, 16 } // [1,2,4,8,16]
#define MICROSTEP_MODES { 16, 16, 16, 16, 16, 16 } // [1,2,4,8,16]
/**
* @section stepper motor current
@ -1122,6 +1123,10 @@
#define E4_SENSE_RESISTOR 91
#define E4_MICROSTEPS 16
#define E5_MAX_CURRENT 1000
#define E5_SENSE_RESISTOR 91
#define E5_MICROSTEPS 16
#endif // TMC26X
// @section tmc_smart
@ -1186,6 +1191,9 @@
#define E4_CURRENT 800
#define E4_MICROSTEPS 16
#define E5_CURRENT 800
#define E5_MICROSTEPS 16
/**
* Use software SPI for TMC2130.
* The default SW SPI pins are defined the respective pins files,
@ -1241,6 +1249,7 @@
#define E2_HYBRID_THRESHOLD 30
#define E3_HYBRID_THRESHOLD 30
#define E4_HYBRID_THRESHOLD 30
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
@ -1358,6 +1367,10 @@
#define E4_OVERCURRENT 2000
#define E4_STALLCURRENT 1500
#define E5_MICROSTEPS 16
#define E5_OVERCURRENT 2000
#define E5_STALLCURRENT 1500
#endif // L6470
/**

11
Marlin/src/config/examples/AlephObjects/TAZ4/Configuration.h

@ -333,6 +333,7 @@
#define TEMP_SENSOR_2 0
#define TEMP_SENSOR_3 0
#define TEMP_SENSOR_4 0
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 7
#define TEMP_SENSOR_CHAMBER 0
@ -363,6 +364,7 @@
#define HEATER_2_MINTEMP 5
#define HEATER_3_MINTEMP 5
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off.
@ -373,6 +375,7 @@
#define HEATER_2_MAXTEMP 250
#define HEATER_3_MAXTEMP 250
#define HEATER_4_MAXTEMP 250
#define HEATER_5_MAXTEMP 250
#define BED_MAXTEMP 150
//===========================================================================
@ -613,6 +616,7 @@
//#define E2_DRIVER_TYPE A4988
//#define E3_DRIVER_TYPE A4988
//#define E4_DRIVER_TYPE A4988
//#define E5_DRIVER_TYPE A4988
// Enable this feature if all enabled endstop pins are interrupt-capable.
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
@ -658,14 +662,14 @@
/**
* Default Axis Steps Per Unit (steps/mm)
* Override with M92
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT { 100.5, 100.5, 400, 850 }
/**
* Default Max Feed Rate (mm/s)
* Override with M203
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_FEEDRATE { 800, 800, 8, 50 }
@ -673,7 +677,7 @@
* Default Max Acceleration (change/s) change = mm/s
* (Maximum start speed for accelerated moves)
* Override with M201
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_ACCELERATION { 9000, 9000, 100, 10000 }
@ -912,6 +916,7 @@
#define INVERT_E2_DIR true
#define INVERT_E3_DIR true
#define INVERT_E4_DIR true
#define INVERT_E5_DIR true
// @section homing

15
Marlin/src/config/examples/AlephObjects/TAZ4/Configuration_adv.h

@ -242,6 +242,7 @@
#define E2_AUTO_FAN_PIN -1
#define E3_AUTO_FAN_PIN -1
#define E4_AUTO_FAN_PIN -1
#define E5_AUTO_FAN_PIN -1
#define CHAMBER_AUTO_FAN_PIN -1
#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed
@ -482,7 +483,7 @@
//#define ADAPTIVE_STEP_SMOOTHING
// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU.
#define MICROSTEP_MODES { 16, 16, 4, 16, 16 } // [1,2,4,8,16]
#define MICROSTEP_MODES { 16, 16, 4, 16, 16, 16 } // [1,2,4,8,16]
/**
* @section stepper motor current
@ -1122,6 +1123,10 @@
#define E4_SENSE_RESISTOR 91
#define E4_MICROSTEPS 16
#define E5_MAX_CURRENT 1000
#define E5_SENSE_RESISTOR 91
#define E5_MICROSTEPS 16
#endif // TMC26X
// @section tmc_smart
@ -1186,6 +1191,9 @@
#define E4_CURRENT 800
#define E4_MICROSTEPS 16
#define E5_CURRENT 800
#define E5_MICROSTEPS 16
/**
* Use software SPI for TMC2130.
* The default SW SPI pins are defined the respective pins files,
@ -1241,6 +1249,7 @@
#define E2_HYBRID_THRESHOLD 30
#define E3_HYBRID_THRESHOLD 30
#define E4_HYBRID_THRESHOLD 30
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
@ -1358,6 +1367,10 @@
#define E4_OVERCURRENT 2000
#define E4_STALLCURRENT 1500
#define E5_MICROSTEPS 16
#define E5_OVERCURRENT 2000
#define E5_STALLCURRENT 1500
#endif // L6470
/**

11
Marlin/src/config/examples/AliExpress/CL-260/Configuration.h

@ -333,6 +333,7 @@
#define TEMP_SENSOR_2 0
#define TEMP_SENSOR_3 0
#define TEMP_SENSOR_4 0
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0
@ -363,6 +364,7 @@
#define HEATER_2_MINTEMP 5
#define HEATER_3_MINTEMP 5
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off.
@ -373,6 +375,7 @@
#define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
//===========================================================================
@ -593,6 +596,7 @@
//#define E2_DRIVER_TYPE A4988
//#define E3_DRIVER_TYPE A4988
//#define E4_DRIVER_TYPE A4988
//#define E5_DRIVER_TYPE A4988
// Enable this feature if all enabled endstop pins are interrupt-capable.
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
@ -638,14 +642,14 @@
/**
* Default Axis Steps Per Unit (steps/mm)
* Override with M92
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 400, 160.6 }
/**
* Default Max Feed Rate (mm/s)
* Override with M203
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_FEEDRATE { 300, 300, 5, 25 }
@ -653,7 +657,7 @@
* Default Max Acceleration (change/s) change = mm/s
* (Maximum start speed for accelerated moves)
* Override with M201
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_ACCELERATION { 3000, 3000, 100, 10000 }
@ -892,6 +896,7 @@
#define INVERT_E2_DIR false
#define INVERT_E3_DIR false
#define INVERT_E4_DIR false
#define INVERT_E5_DIR false
// @section homing

11
Marlin/src/config/examples/Anet/A2/Configuration.h

@ -316,6 +316,7 @@
#define TEMP_SENSOR_2 0
#define TEMP_SENSOR_3 0
#define TEMP_SENSOR_4 0
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 5
#define TEMP_SENSOR_CHAMBER 0
@ -346,6 +347,7 @@
#define HEATER_2_MINTEMP 5
#define HEATER_3_MINTEMP 5
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off.
@ -356,6 +358,7 @@
#define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
//===========================================================================
@ -576,6 +579,7 @@
//#define E2_DRIVER_TYPE A4988
//#define E3_DRIVER_TYPE A4988
//#define E4_DRIVER_TYPE A4988
//#define E5_DRIVER_TYPE A4988
// Enable this feature if all enabled endstop pins are interrupt-capable.
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
@ -621,14 +625,14 @@
/**
* Default Axis Steps Per Unit (steps/mm)
* Override with M92
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT {100, 100, 400, 95 }
/**
* Default Max Feed Rate (mm/s)
* Override with M203
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_FEEDRATE { 300, 300, 5, 25 }
@ -636,7 +640,7 @@
* Default Max Acceleration (change/s) change = mm/s
* (Maximum start speed for accelerated moves)
* Override with M201
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_ACCELERATION { 3000, 3000, 100, 10000 }
@ -875,6 +879,7 @@
#define INVERT_E2_DIR false
#define INVERT_E3_DIR false
#define INVERT_E4_DIR false
#define INVERT_E5_DIR false
// @section homing

15
Marlin/src/config/examples/Anet/A2/Configuration_adv.h

@ -242,6 +242,7 @@
#define E2_AUTO_FAN_PIN -1
#define E3_AUTO_FAN_PIN -1
#define E4_AUTO_FAN_PIN -1
#define E5_AUTO_FAN_PIN -1
#define CHAMBER_AUTO_FAN_PIN -1
#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed
@ -471,7 +472,7 @@
//#define ADAPTIVE_STEP_SMOOTHING
// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU.
#define MICROSTEP_MODES { 16, 16, 16, 16, 16 } // [1,2,4,8,16]
#define MICROSTEP_MODES { 16, 16, 16, 16, 16, 16 } // [1,2,4,8,16]
/**
* @section stepper motor current
@ -1107,6 +1108,10 @@
#define E4_SENSE_RESISTOR 91
#define E4_MICROSTEPS 16
#define E5_MAX_CURRENT 1000
#define E5_SENSE_RESISTOR 91
#define E5_MICROSTEPS 16
#endif // TMC26X
// @section tmc_smart
@ -1168,6 +1173,9 @@
#define E4_CURRENT 800
#define E4_MICROSTEPS 16
#define E5_CURRENT 800
#define E5_MICROSTEPS 16
/**
* Use software SPI for TMC2130.
* The default SW SPI pins are defined the respective pins files,
@ -1223,6 +1231,7 @@
#define E2_HYBRID_THRESHOLD 30
#define E3_HYBRID_THRESHOLD 30
#define E4_HYBRID_THRESHOLD 30
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
@ -1340,6 +1349,10 @@
#define E4_OVERCURRENT 2000
#define E4_STALLCURRENT 1500
#define E5_MICROSTEPS 16
#define E5_OVERCURRENT 2000
#define E5_STALLCURRENT 1500
#endif // L6470
/**

11
Marlin/src/config/examples/Anet/A2plus/Configuration.h

@ -316,6 +316,7 @@
#define TEMP_SENSOR_2 0
#define TEMP_SENSOR_3 0
#define TEMP_SENSOR_4 0
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 5
#define TEMP_SENSOR_CHAMBER 0
@ -346,6 +347,7 @@
#define HEATER_2_MINTEMP 5
#define HEATER_3_MINTEMP 5
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off.
@ -356,6 +358,7 @@
#define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
//===========================================================================
@ -576,6 +579,7 @@
//#define E2_DRIVER_TYPE A4988
//#define E3_DRIVER_TYPE A4988
//#define E4_DRIVER_TYPE A4988
//#define E5_DRIVER_TYPE A4988
// Enable this feature if all enabled endstop pins are interrupt-capable.
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
@ -621,14 +625,14 @@
/**
* Default Axis Steps Per Unit (steps/mm)
* Override with M92
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT {100, 100, 400, 95 }
/**
* Default Max Feed Rate (mm/s)
* Override with M203
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_FEEDRATE { 300, 300, 5, 25 }
@ -636,7 +640,7 @@
* Default Max Acceleration (change/s) change = mm/s
* (Maximum start speed for accelerated moves)
* Override with M201
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_ACCELERATION { 3000, 3000, 100, 10000 }
@ -875,6 +879,7 @@
#define INVERT_E2_DIR false
#define INVERT_E3_DIR false
#define INVERT_E4_DIR false
#define INVERT_E5_DIR false
// @section homing

15
Marlin/src/config/examples/Anet/A2plus/Configuration_adv.h

@ -242,6 +242,7 @@
#define E2_AUTO_FAN_PIN -1
#define E3_AUTO_FAN_PIN -1
#define E4_AUTO_FAN_PIN -1
#define E5_AUTO_FAN_PIN -1
#define CHAMBER_AUTO_FAN_PIN -1
#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed
@ -471,7 +472,7 @@
//#define ADAPTIVE_STEP_SMOOTHING
// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU.
#define MICROSTEP_MODES { 16, 16, 16, 16, 16 } // [1,2,4,8,16]
#define MICROSTEP_MODES { 16, 16, 16, 16, 16, 16 } // [1,2,4,8,16]
/**
* @section stepper motor current
@ -1107,6 +1108,10 @@
#define E4_SENSE_RESISTOR 91
#define E4_MICROSTEPS 16
#define E5_MAX_CURRENT 1000
#define E5_SENSE_RESISTOR 91
#define E5_MICROSTEPS 16
#endif // TMC26X
// @section tmc_smart
@ -1168,6 +1173,9 @@
#define E4_CURRENT 800
#define E4_MICROSTEPS 16
#define E5_CURRENT 800
#define E5_MICROSTEPS 16
/**
* Use software SPI for TMC2130.
* The default SW SPI pins are defined the respective pins files,
@ -1223,6 +1231,7 @@
#define E2_HYBRID_THRESHOLD 30
#define E3_HYBRID_THRESHOLD 30
#define E4_HYBRID_THRESHOLD 30
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
@ -1340,6 +1349,10 @@
#define E4_OVERCURRENT 2000
#define E4_STALLCURRENT 1500
#define E5_MICROSTEPS 16
#define E5_OVERCURRENT 2000
#define E5_STALLCURRENT 1500
#endif // L6470
/**

11
Marlin/src/config/examples/Anet/A6/Configuration.h

@ -333,6 +333,7 @@
#define TEMP_SENSOR_2 0
#define TEMP_SENSOR_3 0
#define TEMP_SENSOR_4 0
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 11
#define TEMP_SENSOR_CHAMBER 0
@ -363,6 +364,7 @@
#define HEATER_2_MINTEMP 5
#define HEATER_3_MINTEMP 5
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off.
@ -373,6 +375,7 @@
#define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 130
//===========================================================================
@ -613,6 +616,7 @@
//#define E2_DRIVER_TYPE A4988
//#define E3_DRIVER_TYPE A4988
//#define E4_DRIVER_TYPE A4988
//#define E5_DRIVER_TYPE A4988
// Enable this feature if all enabled endstop pins are interrupt-capable.
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
@ -658,7 +662,7 @@
/**
* Default Axis Steps Per Unit (steps/mm)
* Override with M92
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
//#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 4000, 500 }
@ -670,7 +674,7 @@
/**
* Default Max Feed Rate (mm/s)
* Override with M203
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
//#define DEFAULT_MAX_FEEDRATE { 300, 300, 5, 25 }
@ -684,7 +688,7 @@
* Default Max Acceleration (change/s) change = mm/s
* (Maximum start speed for accelerated moves)
* Override with M201
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
//#define DEFAULT_MAX_ACCELERATION { 3000, 3000, 100, 10000 }
@ -972,6 +976,7 @@
#define INVERT_E2_DIR false
#define INVERT_E3_DIR false
#define INVERT_E4_DIR false
#define INVERT_E5_DIR false
// @section homing

15
Marlin/src/config/examples/Anet/A6/Configuration_adv.h

@ -242,6 +242,7 @@
#define E2_AUTO_FAN_PIN -1
#define E3_AUTO_FAN_PIN -1
#define E4_AUTO_FAN_PIN -1
#define E5_AUTO_FAN_PIN -1
#define CHAMBER_AUTO_FAN_PIN -1
#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed
@ -482,7 +483,7 @@
//#define ADAPTIVE_STEP_SMOOTHING
// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU.
#define MICROSTEP_MODES { 16, 16, 16, 16, 16 } // [1,2,4,8,16]
#define MICROSTEP_MODES { 16, 16, 16, 16, 16, 16 } // [1,2,4,8,16]
/**
* @section stepper motor current
@ -1122,6 +1123,10 @@
#define E4_SENSE_RESISTOR 91
#define E4_MICROSTEPS 16
#define E5_MAX_CURRENT 1000
#define E5_SENSE_RESISTOR 91
#define E5_MICROSTEPS 16
#endif // TMC26X
// @section tmc_smart
@ -1186,6 +1191,9 @@
#define E4_CURRENT 800
#define E4_MICROSTEPS 16
#define E5_CURRENT 800
#define E5_MICROSTEPS 16
/**
* Use software SPI for TMC2130.
* The default SW SPI pins are defined the respective pins files,
@ -1241,6 +1249,7 @@
#define E2_HYBRID_THRESHOLD 30
#define E3_HYBRID_THRESHOLD 30
#define E4_HYBRID_THRESHOLD 30
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
@ -1358,6 +1367,10 @@
#define E4_OVERCURRENT 2000
#define E4_STALLCURRENT 1500
#define E5_MICROSTEPS 16
#define E5_OVERCURRENT 2000
#define E5_STALLCURRENT 1500
#endif // L6470
/**

11
Marlin/src/config/examples/Anet/A8/Configuration.h

@ -334,6 +334,7 @@
#define TEMP_SENSOR_2 0
#define TEMP_SENSOR_3 0
#define TEMP_SENSOR_4 0
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 5
#define TEMP_SENSOR_CHAMBER 0
@ -364,6 +365,7 @@
#define HEATER_2_MINTEMP 5
#define HEATER_3_MINTEMP 5
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off.
@ -374,6 +376,7 @@
#define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 130
//===========================================================================
@ -600,6 +603,7 @@
//#define E2_DRIVER_TYPE A4988
//#define E3_DRIVER_TYPE A4988
//#define E4_DRIVER_TYPE A4988
//#define E5_DRIVER_TYPE A4988
// Enable this feature if all enabled endstop pins are interrupt-capable.
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
@ -645,14 +649,14 @@
/**
* Default Axis Steps Per Unit (steps/mm)
* Override with M92
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT { 100, 100, 400, 100 }
/**
* Default Max Feed Rate (mm/s)
* Override with M203
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_FEEDRATE { 400, 400, 8, 50 }
@ -660,7 +664,7 @@
* Default Max Acceleration (change/s) change = mm/s
* (Maximum start speed for accelerated moves)
* Override with M201
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_ACCELERATION { 2000, 2000, 100, 10000 }
@ -899,6 +903,7 @@
#define INVERT_E2_DIR false
#define INVERT_E3_DIR false
#define INVERT_E4_DIR false
#define INVERT_E5_DIR false
// @section homing

15
Marlin/src/config/examples/Anet/A8/Configuration_adv.h

@ -242,6 +242,7 @@
#define E2_AUTO_FAN_PIN -1
#define E3_AUTO_FAN_PIN -1
#define E4_AUTO_FAN_PIN -1
#define E5_AUTO_FAN_PIN -1
#define CHAMBER_AUTO_FAN_PIN -1
#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed
@ -482,7 +483,7 @@
//#define ADAPTIVE_STEP_SMOOTHING
// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU.
#define MICROSTEP_MODES { 16, 16, 16, 16, 16 } // [1,2,4,8,16]
#define MICROSTEP_MODES { 16, 16, 16, 16, 16, 16 } // [1,2,4,8,16]
/**
* @section stepper motor current
@ -1122,6 +1123,10 @@
#define E4_SENSE_RESISTOR 91
#define E4_MICROSTEPS 16
#define E5_MAX_CURRENT 1000
#define E5_SENSE_RESISTOR 91
#define E5_MICROSTEPS 16
#endif // TMC26X
// @section tmc_smart
@ -1186,6 +1191,9 @@
#define E4_CURRENT 800
#define E4_MICROSTEPS 16
#define E5_CURRENT 800
#define E5_MICROSTEPS 16
/**
* Use software SPI for TMC2130.
* The default SW SPI pins are defined the respective pins files,
@ -1241,6 +1249,7 @@
#define E2_HYBRID_THRESHOLD 30
#define E3_HYBRID_THRESHOLD 30
#define E4_HYBRID_THRESHOLD 30
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
@ -1358,6 +1367,10 @@
#define E4_OVERCURRENT 2000
#define E4_STALLCURRENT 1500
#define E5_MICROSTEPS 16
#define E5_OVERCURRENT 2000
#define E5_STALLCURRENT 1500
#endif // L6470
/**

11
Marlin/src/config/examples/Azteeg/X5GT/Configuration.h

@ -333,6 +333,7 @@
#define TEMP_SENSOR_2 0
#define TEMP_SENSOR_3 0
#define TEMP_SENSOR_4 0
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0
@ -363,6 +364,7 @@
#define HEATER_2_MINTEMP 5
#define HEATER_3_MINTEMP 5
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off.
@ -373,6 +375,7 @@
#define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
//===========================================================================
@ -593,6 +596,7 @@
//#define E2_DRIVER_TYPE A4988
//#define E3_DRIVER_TYPE A4988
//#define E4_DRIVER_TYPE A4988
//#define E5_DRIVER_TYPE A4988
// Enable this feature if all enabled endstop pins are interrupt-capable.
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
@ -638,14 +642,14 @@
/**
* Default Axis Steps Per Unit (steps/mm)
* Override with M92
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 4000, 500 }
/**
* Default Max Feed Rate (mm/s)
* Override with M203
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_FEEDRATE { 300, 300, 5, 25 }
@ -653,7 +657,7 @@
* Default Max Acceleration (change/s) change = mm/s
* (Maximum start speed for accelerated moves)
* Override with M201
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_ACCELERATION { 3000, 3000, 100, 10000 }
@ -892,6 +896,7 @@
#define INVERT_E2_DIR false
#define INVERT_E3_DIR false
#define INVERT_E4_DIR false
#define INVERT_E5_DIR false
// @section homing

15
Marlin/src/config/examples/Azteeg/X5GT/Configuration_adv.h

@ -242,6 +242,7 @@
#define E2_AUTO_FAN_PIN -1
#define E3_AUTO_FAN_PIN -1
#define E4_AUTO_FAN_PIN -1
#define E5_AUTO_FAN_PIN -1
#define CHAMBER_AUTO_FAN_PIN -1
#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed
@ -482,7 +483,7 @@
//#define ADAPTIVE_STEP_SMOOTHING
// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU.
#define MICROSTEP_MODES { 16, 16, 16, 16, 16 } // [1,2,4,8,16]
#define MICROSTEP_MODES { 16, 16, 16, 16, 16, 16 } // [1,2,4,8,16]
/**
* @section stepper motor current
@ -1122,6 +1123,10 @@
#define E4_SENSE_RESISTOR 91
#define E4_MICROSTEPS 16
#define E5_MAX_CURRENT 1000
#define E5_SENSE_RESISTOR 91
#define E5_MICROSTEPS 16
#endif // TMC26X
// @section tmc_smart
@ -1186,6 +1191,9 @@
#define E4_CURRENT 800
#define E4_MICROSTEPS 16
#define E5_CURRENT 800
#define E5_MICROSTEPS 16
/**
* Use software SPI for TMC2130.
* The default SW SPI pins are defined the respective pins files,
@ -1241,6 +1249,7 @@
#define E2_HYBRID_THRESHOLD 30
#define E3_HYBRID_THRESHOLD 30
#define E4_HYBRID_THRESHOLD 30
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
@ -1358,6 +1367,10 @@
#define E4_OVERCURRENT 2000
#define E4_STALLCURRENT 1500
#define E5_MICROSTEPS 16
#define E5_OVERCURRENT 2000
#define E5_STALLCURRENT 1500
#endif // L6470
/**

10
Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration.h

@ -333,6 +333,7 @@
#define TEMP_SENSOR_2 0
#define TEMP_SENSOR_3 0
#define TEMP_SENSOR_4 0
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 5
#define TEMP_SENSOR_CHAMBER 0
@ -363,6 +364,7 @@
#define HEATER_2_MINTEMP 5
#define HEATER_3_MINTEMP 5
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off.
@ -373,6 +375,7 @@
#define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 115
//===========================================================================
@ -611,14 +614,14 @@
/**
* Default Axis Steps Per Unit (steps/mm)
* Override with M92
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT { 100, 100, 400, 400}
/**
* Default Max Feed Rate (mm/s)
* Override with M203
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_FEEDRATE { 350, 350, 10, 50 }
@ -626,7 +629,7 @@
* Default Max Acceleration (change/s) change = mm/s
* (Maximum start speed for accelerated moves)
* Override with M201
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_ACCELERATION { 1100, 1100, 300, 2500 }
@ -865,6 +868,7 @@
#define INVERT_E2_DIR false
#define INVERT_E3_DIR false
#define INVERT_E4_DIR false
#define INVERT_E5_DIR false
// @section homing

15
Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h

@ -242,6 +242,7 @@
#define E2_AUTO_FAN_PIN -1
#define E3_AUTO_FAN_PIN -1
#define E4_AUTO_FAN_PIN -1
#define E5_AUTO_FAN_PIN -1
#define CHAMBER_AUTO_FAN_PIN -1
#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed
@ -482,7 +483,7 @@
//#define ADAPTIVE_STEP_SMOOTHING
// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU.
#define MICROSTEP_MODES { 16, 16, 16, 16, 16 } // [1,2,4,8,16]
#define MICROSTEP_MODES { 16, 16, 16, 16, 16, 16 } // [1,2,4,8,16]
/**
* @section stepper motor current
@ -1122,6 +1123,10 @@
#define E4_SENSE_RESISTOR 91
#define E4_MICROSTEPS 16
#define E5_MAX_CURRENT 1000
#define E5_SENSE_RESISTOR 91
#define E5_MICROSTEPS 16
#endif // TMC26X
// @section tmc_smart
@ -1186,6 +1191,9 @@
#define E4_CURRENT 800
#define E4_MICROSTEPS 16
#define E5_CURRENT 800
#define E5_MICROSTEPS 16
/**
* Use software SPI for TMC2130.
* The default SW SPI pins are defined the respective pins files,
@ -1241,6 +1249,7 @@
#define E2_HYBRID_THRESHOLD 30
#define E3_HYBRID_THRESHOLD 30
#define E4_HYBRID_THRESHOLD 30
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
@ -1358,6 +1367,10 @@
#define E4_OVERCURRENT 2000
#define E4_STALLCURRENT 1500
#define E5_MICROSTEPS 16
#define E5_OVERCURRENT 2000
#define E5_STALLCURRENT 1500
#endif // L6470
/**

10
Marlin/src/config/examples/BIBO/TouchX/default/Configuration.h

@ -333,6 +333,7 @@
#define TEMP_SENSOR_2 0
#define TEMP_SENSOR_3 0
#define TEMP_SENSOR_4 0
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 60
#define TEMP_SENSOR_CHAMBER 0
@ -363,6 +364,7 @@
#define HEATER_2_MINTEMP 5
#define HEATER_3_MINTEMP 5
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off.
@ -373,6 +375,7 @@
#define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 115
//===========================================================================
@ -611,14 +614,14 @@
/**
* Default Axis Steps Per Unit (steps/mm)
* Override with M92
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT { 100, 100, 400, 93.6 }
/**
* Default Max Feed Rate (mm/s)
* Override with M203
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_FEEDRATE { 350, 350, 10, 25 }
@ -626,7 +629,7 @@
* Default Max Acceleration (change/s) change = mm/s
* (Maximum start speed for accelerated moves)
* Override with M201
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_ACCELERATION { 1100, 1100, 300, 5000 }
@ -865,6 +868,7 @@
#define INVERT_E2_DIR false
#define INVERT_E3_DIR false
#define INVERT_E4_DIR false
#define INVERT_E5_DIR false
// @section homing

15
Marlin/src/config/examples/BIBO/TouchX/default/Configuration_adv.h

@ -242,6 +242,7 @@
#define E2_AUTO_FAN_PIN -1
#define E3_AUTO_FAN_PIN -1
#define E4_AUTO_FAN_PIN -1
#define E5_AUTO_FAN_PIN -1
#define CHAMBER_AUTO_FAN_PIN -1
#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed
@ -482,7 +483,7 @@
//#define ADAPTIVE_STEP_SMOOTHING
// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU.
#define MICROSTEP_MODES { 16, 16, 16, 16, 16 } // [1,2,4,8,16]
#define MICROSTEP_MODES { 16, 16, 16, 16, 16, 16 } // [1,2,4,8,16]
/**
* @section stepper motor current
@ -1122,6 +1123,10 @@
#define E4_SENSE_RESISTOR 91
#define E4_MICROSTEPS 16
#define E5_MAX_CURRENT 1000
#define E5_SENSE_RESISTOR 91
#define E5_MICROSTEPS 16
#endif // TMC26X
// @section tmc_smart
@ -1186,6 +1191,9 @@
#define E4_CURRENT 800
#define E4_MICROSTEPS 16
#define E5_CURRENT 800
#define E5_MICROSTEPS 16
/**
* Use software SPI for TMC2130.
* The default SW SPI pins are defined the respective pins files,
@ -1241,6 +1249,7 @@
#define E2_HYBRID_THRESHOLD 30
#define E3_HYBRID_THRESHOLD 30
#define E4_HYBRID_THRESHOLD 30
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
@ -1358,6 +1367,10 @@
#define E4_OVERCURRENT 2000
#define E4_STALLCURRENT 1500
#define E5_MICROSTEPS 16
#define E5_OVERCURRENT 2000
#define E5_STALLCURRENT 1500
#endif // L6470
/**

11
Marlin/src/config/examples/BQ/Hephestos/Configuration.h

@ -333,6 +333,7 @@
#define TEMP_SENSOR_2 0
#define TEMP_SENSOR_3 0
#define TEMP_SENSOR_4 0
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 0
#define TEMP_SENSOR_CHAMBER 0
@ -363,6 +364,7 @@
#define HEATER_2_MINTEMP 5
#define HEATER_3_MINTEMP 5
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off.
@ -373,6 +375,7 @@
#define HEATER_2_MAXTEMP 260
#define HEATER_3_MAXTEMP 260
#define HEATER_4_MAXTEMP 260
#define HEATER_5_MAXTEMP 260
#define BED_MAXTEMP 150
//===========================================================================
@ -581,6 +584,7 @@
//#define E2_DRIVER_TYPE A4988
//#define E3_DRIVER_TYPE A4988
//#define E4_DRIVER_TYPE A4988
//#define E5_DRIVER_TYPE A4988
// Enable this feature if all enabled endstop pins are interrupt-capable.
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
@ -626,14 +630,14 @@
/**
* Default Axis Steps Per Unit (steps/mm)
* Override with M92
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 4000, 100.47095761381482 }
/**
* Default Max Feed Rate (mm/s)
* Override with M203
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_FEEDRATE { 200, 200, 3.3, 25 }
@ -641,7 +645,7 @@
* Default Max Acceleration (change/s) change = mm/s
* (Maximum start speed for accelerated moves)
* Override with M201
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_ACCELERATION { 1100, 1100, 100, 10000 }
@ -880,6 +884,7 @@
#define INVERT_E2_DIR false
#define INVERT_E3_DIR false
#define INVERT_E4_DIR false
#define INVERT_E5_DIR false
// @section homing

15
Marlin/src/config/examples/BQ/Hephestos/Configuration_adv.h

@ -242,6 +242,7 @@
#define E2_AUTO_FAN_PIN -1
#define E3_AUTO_FAN_PIN -1
#define E4_AUTO_FAN_PIN -1
#define E5_AUTO_FAN_PIN -1
#define CHAMBER_AUTO_FAN_PIN -1
#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed
@ -482,7 +483,7 @@
//#define ADAPTIVE_STEP_SMOOTHING
// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU.
#define MICROSTEP_MODES { 16, 16, 16, 16, 16 } // [1,2,4,8,16]
#define MICROSTEP_MODES { 16, 16, 16, 16, 16, 16 } // [1,2,4,8,16]
/**
* @section stepper motor current
@ -1122,6 +1123,10 @@
#define E4_SENSE_RESISTOR 91
#define E4_MICROSTEPS 16
#define E5_MAX_CURRENT 1000
#define E5_SENSE_RESISTOR 91
#define E5_MICROSTEPS 16
#endif // TMC26X
// @section tmc_smart
@ -1186,6 +1191,9 @@
#define E4_CURRENT 800
#define E4_MICROSTEPS 16
#define E5_CURRENT 800
#define E5_MICROSTEPS 16
/**
* Use software SPI for TMC2130.
* The default SW SPI pins are defined the respective pins files,
@ -1241,6 +1249,7 @@
#define E2_HYBRID_THRESHOLD 30
#define E3_HYBRID_THRESHOLD 30
#define E4_HYBRID_THRESHOLD 30
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
@ -1358,6 +1367,10 @@
#define E4_OVERCURRENT 2000
#define E4_STALLCURRENT 1500
#define E5_MICROSTEPS 16
#define E5_OVERCURRENT 2000
#define E5_STALLCURRENT 1500
#endif // L6470
/**

11
Marlin/src/config/examples/BQ/Hephestos_2/Configuration.h

@ -341,6 +341,7 @@
#define TEMP_SENSOR_2 0
#define TEMP_SENSOR_3 0
#define TEMP_SENSOR_4 0
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 0
#define TEMP_SENSOR_CHAMBER 0
@ -371,6 +372,7 @@
#define HEATER_2_MINTEMP 5
#define HEATER_3_MINTEMP 5
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off.
@ -381,6 +383,7 @@
#define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 100
//===========================================================================
@ -594,6 +597,7 @@
//#define E2_DRIVER_TYPE A4988
//#define E3_DRIVER_TYPE A4988
//#define E4_DRIVER_TYPE A4988
//#define E5_DRIVER_TYPE A4988
// Enable this feature if all enabled endstop pins are interrupt-capable.
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
@ -639,14 +643,14 @@
/**
* Default Axis Steps Per Unit (steps/mm)
* Override with M92
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT { 160, 160, 8000, 218.77 }
/**
* Default Max Feed Rate (mm/s)
* Override with M203
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_FEEDRATE { 300, 300, 3, 120 }
@ -654,7 +658,7 @@
* Default Max Acceleration (change/s) change = mm/s
* (Maximum start speed for accelerated moves)
* Override with M201
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_ACCELERATION { 3000, 3000, 100, 3000 }
@ -893,6 +897,7 @@
#define INVERT_E2_DIR false
#define INVERT_E3_DIR false
#define INVERT_E4_DIR false
#define INVERT_E5_DIR false
// @section homing

15
Marlin/src/config/examples/BQ/Hephestos_2/Configuration_adv.h

@ -242,6 +242,7 @@
#define E2_AUTO_FAN_PIN -1
#define E3_AUTO_FAN_PIN -1
#define E4_AUTO_FAN_PIN -1
#define E5_AUTO_FAN_PIN -1
#define CHAMBER_AUTO_FAN_PIN -1
#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed
@ -482,7 +483,7 @@
//#define ADAPTIVE_STEP_SMOOTHING
// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU.
#define MICROSTEP_MODES { 16, 16, 16, 16, 16 } // [1,2,4,8,16]
#define MICROSTEP_MODES { 16, 16, 16, 16, 16, 16 } // [1,2,4,8,16]
/**
* @section stepper motor current
@ -1130,6 +1131,10 @@
#define E4_SENSE_RESISTOR 91
#define E4_MICROSTEPS 16
#define E5_MAX_CURRENT 1000
#define E5_SENSE_RESISTOR 91
#define E5_MICROSTEPS 16
#endif // TMC26X
// @section tmc_smart
@ -1194,6 +1199,9 @@
#define E4_CURRENT 800
#define E4_MICROSTEPS 16
#define E5_CURRENT 800
#define E5_MICROSTEPS 16
/**
* Use software SPI for TMC2130.
* The default SW SPI pins are defined the respective pins files,
@ -1249,6 +1257,7 @@
#define E2_HYBRID_THRESHOLD 30
#define E3_HYBRID_THRESHOLD 30
#define E4_HYBRID_THRESHOLD 30
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
@ -1366,6 +1375,10 @@
#define E4_OVERCURRENT 2000
#define E4_STALLCURRENT 1500
#define E5_MICROSTEPS 16
#define E5_OVERCURRENT 2000
#define E5_STALLCURRENT 1500
#endif // L6470
/**

11
Marlin/src/config/examples/BQ/WITBOX/Configuration.h

@ -333,6 +333,7 @@
#define TEMP_SENSOR_2 0
#define TEMP_SENSOR_3 0
#define TEMP_SENSOR_4 0
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 0
#define TEMP_SENSOR_CHAMBER 0
@ -363,6 +364,7 @@
#define HEATER_2_MINTEMP 5
#define HEATER_3_MINTEMP 5
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off.
@ -373,6 +375,7 @@
#define HEATER_2_MAXTEMP 260
#define HEATER_3_MAXTEMP 260
#define HEATER_4_MAXTEMP 260
#define HEATER_5_MAXTEMP 260
#define BED_MAXTEMP 150
//===========================================================================
@ -581,6 +584,7 @@
//#define E2_DRIVER_TYPE A4988
//#define E3_DRIVER_TYPE A4988
//#define E4_DRIVER_TYPE A4988
//#define E5_DRIVER_TYPE A4988
// Enable this feature if all enabled endstop pins are interrupt-capable.
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
@ -626,14 +630,14 @@
/**
* Default Axis Steps Per Unit (steps/mm)
* Override with M92
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 600.0*8/3, 102.073 }
/**
* Default Max Feed Rate (mm/s)
* Override with M203
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_FEEDRATE { 350, 350, 7.2, 80 }
@ -641,7 +645,7 @@
* Default Max Acceleration (change/s) change = mm/s
* (Maximum start speed for accelerated moves)
* Override with M201
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_ACCELERATION { 1000, 1000, 10, 1000 }
@ -880,6 +884,7 @@
#define INVERT_E2_DIR false
#define INVERT_E3_DIR false
#define INVERT_E4_DIR false
#define INVERT_E5_DIR false
// @section homing

15
Marlin/src/config/examples/BQ/WITBOX/Configuration_adv.h

@ -242,6 +242,7 @@
#define E2_AUTO_FAN_PIN -1
#define E3_AUTO_FAN_PIN -1
#define E4_AUTO_FAN_PIN -1
#define E5_AUTO_FAN_PIN -1
#define CHAMBER_AUTO_FAN_PIN -1
#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed
@ -482,7 +483,7 @@
//#define ADAPTIVE_STEP_SMOOTHING
// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU.
#define MICROSTEP_MODES { 16, 16, 16, 16, 16 } // [1,2,4,8,16]
#define MICROSTEP_MODES { 16, 16, 16, 16, 16, 16 } // [1,2,4,8,16]
/**
* @section stepper motor current
@ -1122,6 +1123,10 @@
#define E4_SENSE_RESISTOR 91
#define E4_MICROSTEPS 16
#define E5_MAX_CURRENT 1000
#define E5_SENSE_RESISTOR 91
#define E5_MICROSTEPS 16
#endif // TMC26X
// @section tmc_smart
@ -1186,6 +1191,9 @@
#define E4_CURRENT 800
#define E4_MICROSTEPS 16
#define E5_CURRENT 800
#define E5_MICROSTEPS 16
/**
* Use software SPI for TMC2130.
* The default SW SPI pins are defined the respective pins files,
@ -1241,6 +1249,7 @@
#define E2_HYBRID_THRESHOLD 30
#define E3_HYBRID_THRESHOLD 30
#define E4_HYBRID_THRESHOLD 30
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
@ -1358,6 +1367,10 @@
#define E4_OVERCURRENT 2000
#define E4_STALLCURRENT 1500
#define E5_MICROSTEPS 16
#define E5_OVERCURRENT 2000
#define E5_STALLCURRENT 1500
#endif // L6470
/**

11
Marlin/src/config/examples/Cartesio/Configuration.h

@ -334,6 +334,7 @@
#define TEMP_SENSOR_2 1
#define TEMP_SENSOR_3 0
#define TEMP_SENSOR_4 0
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0
@ -364,6 +365,7 @@
#define HEATER_2_MINTEMP 5
#define HEATER_3_MINTEMP 5
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off.
@ -374,6 +376,7 @@
#define HEATER_2_MAXTEMP 415
#define HEATER_3_MAXTEMP 415
#define HEATER_4_MAXTEMP 415
#define HEATER_5_MAXTEMP 415
#define BED_MAXTEMP 165
//===========================================================================
@ -592,6 +595,7 @@
//#define E2_DRIVER_TYPE A4988
//#define E3_DRIVER_TYPE A4988
//#define E4_DRIVER_TYPE A4988
//#define E5_DRIVER_TYPE A4988
// Enable this feature if all enabled endstop pins are interrupt-capable.
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
@ -637,14 +641,14 @@
/**
* Default Axis Steps Per Unit (steps/mm)
* Override with M92
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT { 71.128, 71.128, 640, 152 }
/**
* Default Max Feed Rate (mm/s)
* Override with M203
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_FEEDRATE { 200, 200, 20, 20 }
@ -652,7 +656,7 @@
* Default Max Acceleration (change/s) change = mm/s
* (Maximum start speed for accelerated moves)
* Override with M201
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_ACCELERATION { 1000, 1000, 100, 10000 }
@ -891,6 +895,7 @@
#define INVERT_E2_DIR false
#define INVERT_E3_DIR false
#define INVERT_E4_DIR false
#define INVERT_E5_DIR false
// @section homing

15
Marlin/src/config/examples/Cartesio/Configuration_adv.h

@ -242,6 +242,7 @@
#define E2_AUTO_FAN_PIN -1
#define E3_AUTO_FAN_PIN -1
#define E4_AUTO_FAN_PIN -1
#define E5_AUTO_FAN_PIN -1
#define CHAMBER_AUTO_FAN_PIN -1
#define EXTRUDER_AUTO_FAN_TEMPERATURE 35
#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed
@ -482,7 +483,7 @@
//#define ADAPTIVE_STEP_SMOOTHING
// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU.
#define MICROSTEP_MODES { 16, 16, 16, 16, 16 } // [1,2,4,8,16]
#define MICROSTEP_MODES { 16, 16, 16, 16, 16, 16 } // [1,2,4,8,16]
/**
* @section stepper motor current
@ -1122,6 +1123,10 @@
#define E4_SENSE_RESISTOR 91
#define E4_MICROSTEPS 16
#define E5_MAX_CURRENT 1000
#define E5_SENSE_RESISTOR 91
#define E5_MICROSTEPS 16
#endif // TMC26X
// @section tmc_smart
@ -1186,6 +1191,9 @@
#define E4_CURRENT 800
#define E4_MICROSTEPS 16
#define E5_CURRENT 800
#define E5_MICROSTEPS 16
/**
* Use software SPI for TMC2130.
* The default SW SPI pins are defined the respective pins files,
@ -1241,6 +1249,7 @@
#define E2_HYBRID_THRESHOLD 30
#define E3_HYBRID_THRESHOLD 30
#define E4_HYBRID_THRESHOLD 30
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
@ -1358,6 +1367,10 @@
#define E4_OVERCURRENT 2000
#define E4_STALLCURRENT 1500
#define E5_MICROSTEPS 16
#define E5_OVERCURRENT 2000
#define E5_STALLCURRENT 1500
#endif // L6470
/**

11
Marlin/src/config/examples/Creality/CR-10/Configuration.h

@ -333,6 +333,7 @@
#define TEMP_SENSOR_2 0
#define TEMP_SENSOR_3 0
#define TEMP_SENSOR_4 0
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 5
#define TEMP_SENSOR_CHAMBER 0
@ -363,6 +364,7 @@
#define HEATER_2_MINTEMP 5
#define HEATER_3_MINTEMP 5
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off.
@ -373,6 +375,7 @@
#define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 120
//===========================================================================
@ -603,6 +606,7 @@
//#define E2_DRIVER_TYPE A4988
//#define E3_DRIVER_TYPE A4988
//#define E4_DRIVER_TYPE A4988
//#define E5_DRIVER_TYPE A4988
// Enable this feature if all enabled endstop pins are interrupt-capable.
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
@ -648,14 +652,14 @@
/**
* Default Axis Steps Per Unit (steps/mm)
* Override with M92
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 400, 95 }
/**
* Default Max Feed Rate (mm/s)
* Override with M203
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_FEEDRATE { 500, 500, 15, 25 }
@ -663,7 +667,7 @@
* Default Max Acceleration (change/s) change = mm/s
* (Maximum start speed for accelerated moves)
* Override with M201
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_ACCELERATION { 500, 500, 100, 5000 }
@ -902,6 +906,7 @@
#define INVERT_E2_DIR false
#define INVERT_E3_DIR false
#define INVERT_E4_DIR false
#define INVERT_E5_DIR false
// @section homing

15
Marlin/src/config/examples/Creality/CR-10/Configuration_adv.h

@ -242,6 +242,7 @@
#define E2_AUTO_FAN_PIN -1
#define E3_AUTO_FAN_PIN -1
#define E4_AUTO_FAN_PIN -1
#define E5_AUTO_FAN_PIN -1
#define CHAMBER_AUTO_FAN_PIN -1
#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed
@ -482,7 +483,7 @@
//#define ADAPTIVE_STEP_SMOOTHING
// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU.
#define MICROSTEP_MODES { 16, 16, 16, 16, 16 } // [1,2,4,8,16]
#define MICROSTEP_MODES { 16, 16, 16, 16, 16, 16 } // [1,2,4,8,16]
/**
* @section stepper motor current
@ -1122,6 +1123,10 @@
#define E4_SENSE_RESISTOR 91
#define E4_MICROSTEPS 16
#define E5_MAX_CURRENT 1000
#define E5_SENSE_RESISTOR 91
#define E5_MICROSTEPS 16
#endif // TMC26X
// @section tmc_smart
@ -1186,6 +1191,9 @@
#define E4_CURRENT 800
#define E4_MICROSTEPS 16
#define E5_CURRENT 800
#define E5_MICROSTEPS 16
/**
* Use software SPI for TMC2130.
* The default SW SPI pins are defined the respective pins files,
@ -1241,6 +1249,7 @@
#define E2_HYBRID_THRESHOLD 30
#define E3_HYBRID_THRESHOLD 30
#define E4_HYBRID_THRESHOLD 30
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
@ -1358,6 +1367,10 @@
#define E4_OVERCURRENT 2000
#define E4_STALLCURRENT 1500
#define E5_MICROSTEPS 16
#define E5_OVERCURRENT 2000
#define E5_STALLCURRENT 1500
#endif // L6470
/**

11
Marlin/src/config/examples/Creality/CR-10S/Configuration.h

@ -337,6 +337,7 @@
#define TEMP_SENSOR_2 0
#define TEMP_SENSOR_3 0
#define TEMP_SENSOR_4 0
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 5
#define TEMP_SENSOR_CHAMBER 0
@ -367,6 +368,7 @@
#define HEATER_2_MINTEMP 5
#define HEATER_3_MINTEMP 5
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off.
@ -377,6 +379,7 @@
#define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 120
//===========================================================================
@ -597,6 +600,7 @@
//#define E2_DRIVER_TYPE A4988
//#define E3_DRIVER_TYPE A4988
//#define E4_DRIVER_TYPE A4988
//#define E5_DRIVER_TYPE A4988
// Enable this feature if all enabled endstop pins are interrupt-capable.
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
@ -642,14 +646,14 @@
/**
* Default Axis Steps Per Unit (steps/mm)
* Override with M92
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 400, 95 }
/**
* Default Max Feed Rate (mm/s)
* Override with M203
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_FEEDRATE { 2500, 2500, 100, 25 }
@ -657,7 +661,7 @@
* Default Max Acceleration (change/s) change = mm/s
* (Maximum start speed for accelerated moves)
* Override with M201
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_ACCELERATION { 500, 500, 100, 5000 }
@ -896,6 +900,7 @@
#define INVERT_E2_DIR false
#define INVERT_E3_DIR false
#define INVERT_E4_DIR false
#define INVERT_E5_DIR false
// @section homing

15
Marlin/src/config/examples/Creality/CR-10S/Configuration_adv.h

@ -242,6 +242,7 @@
#define E2_AUTO_FAN_PIN -1
#define E3_AUTO_FAN_PIN -1
#define E4_AUTO_FAN_PIN -1
#define E5_AUTO_FAN_PIN -1
#define CHAMBER_AUTO_FAN_PIN -1
#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed
@ -482,7 +483,7 @@
//#define ADAPTIVE_STEP_SMOOTHING
// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU.
#define MICROSTEP_MODES { 16, 16, 16, 16, 16 } // [1,2,4,8,16]
#define MICROSTEP_MODES { 16, 16, 16, 16, 16, 16 } // [1,2,4,8,16]
/**
* @section stepper motor current
@ -1122,6 +1123,10 @@
#define E4_SENSE_RESISTOR 91
#define E4_MICROSTEPS 16
#define E5_MAX_CURRENT 1000
#define E5_SENSE_RESISTOR 91
#define E5_MICROSTEPS 16
#endif // TMC26X
// @section tmc_smart
@ -1186,6 +1191,9 @@
#define E4_CURRENT 800
#define E4_MICROSTEPS 16
#define E5_CURRENT 800
#define E5_MICROSTEPS 16
/**
* Use software SPI for TMC2130.
* The default SW SPI pins are defined the respective pins files,
@ -1241,6 +1249,7 @@
#define E2_HYBRID_THRESHOLD 30
#define E3_HYBRID_THRESHOLD 30
#define E4_HYBRID_THRESHOLD 30
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
@ -1358,6 +1367,10 @@
#define E4_OVERCURRENT 2000
#define E4_STALLCURRENT 1500
#define E5_MICROSTEPS 16
#define E5_OVERCURRENT 2000
#define E5_STALLCURRENT 1500
#endif // L6470
/**

11
Marlin/src/config/examples/Creality/CR-10mini/Configuration.h

@ -342,6 +342,7 @@
#define TEMP_SENSOR_2 0
#define TEMP_SENSOR_3 0
#define TEMP_SENSOR_4 0
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 5
#define TEMP_SENSOR_CHAMBER 0
@ -372,6 +373,7 @@
#define HEATER_2_MINTEMP 5
#define HEATER_3_MINTEMP 5
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off.
@ -382,6 +384,7 @@
#define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 120
//===========================================================================
@ -612,6 +615,7 @@
//#define E2_DRIVER_TYPE A4988
//#define E3_DRIVER_TYPE A4988
//#define E4_DRIVER_TYPE A4988
//#define E5_DRIVER_TYPE A4988
// Enable this feature if all enabled endstop pins are interrupt-capable.
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
@ -657,14 +661,14 @@
/**
* Default Axis Steps Per Unit (steps/mm)
* Override with M92
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT { 79.60, 80, 400, 229.4 }
/**
* Default Max Feed Rate (mm/s)
* Override with M203
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_FEEDRATE { 500, 500, 15, 25 }
@ -672,7 +676,7 @@
* Default Max Acceleration (change/s) change = mm/s
* (Maximum start speed for accelerated moves)
* Override with M201
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_ACCELERATION { 500, 500, 100, 5000 }
@ -911,6 +915,7 @@
#define INVERT_E2_DIR false
#define INVERT_E3_DIR false
#define INVERT_E4_DIR false
#define INVERT_E5_DIR false
// @section homing

15
Marlin/src/config/examples/Creality/CR-10mini/Configuration_adv.h

@ -242,6 +242,7 @@
#define E2_AUTO_FAN_PIN -1
#define E3_AUTO_FAN_PIN -1
#define E4_AUTO_FAN_PIN -1
#define E5_AUTO_FAN_PIN -1
#define CHAMBER_AUTO_FAN_PIN -1
#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed
@ -482,7 +483,7 @@
//#define ADAPTIVE_STEP_SMOOTHING
// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU.
#define MICROSTEP_MODES { 16, 16, 16, 16, 16 } // [1,2,4,8,16]
#define MICROSTEP_MODES { 16, 16, 16, 16, 16, 16 } // [1,2,4,8,16]
/**
* @section stepper motor current
@ -1122,6 +1123,10 @@
#define E4_SENSE_RESISTOR 91
#define E4_MICROSTEPS 16
#define E5_MAX_CURRENT 1000
#define E5_SENSE_RESISTOR 91
#define E5_MICROSTEPS 16
#endif // TMC26X
// @section tmc_smart
@ -1186,6 +1191,9 @@
#define E4_CURRENT 800
#define E4_MICROSTEPS 16
#define E5_CURRENT 800
#define E5_MICROSTEPS 16
/**
* Use software SPI for TMC2130.
* The default SW SPI pins are defined the respective pins files,
@ -1241,6 +1249,7 @@
#define E2_HYBRID_THRESHOLD 30
#define E3_HYBRID_THRESHOLD 30
#define E4_HYBRID_THRESHOLD 30
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
@ -1358,6 +1367,10 @@
#define E4_OVERCURRENT 2000
#define E4_STALLCURRENT 1500
#define E5_MICROSTEPS 16
#define E5_OVERCURRENT 2000
#define E5_STALLCURRENT 1500
#endif // L6470
/**

11
Marlin/src/config/examples/Creality/CR-8/Configuration.h

@ -333,6 +333,7 @@
#define TEMP_SENSOR_2 0
#define TEMP_SENSOR_3 0
#define TEMP_SENSOR_4 0
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0
@ -363,6 +364,7 @@
#define HEATER_2_MINTEMP 5
#define HEATER_3_MINTEMP 5
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off.
@ -373,6 +375,7 @@
#define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
//===========================================================================
@ -603,6 +606,7 @@
//#define E2_DRIVER_TYPE A4988
//#define E3_DRIVER_TYPE A4988
//#define E4_DRIVER_TYPE A4988
//#define E5_DRIVER_TYPE A4988
// Enable this feature if all enabled endstop pins are interrupt-capable.
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
@ -648,14 +652,14 @@
/**
* Default Axis Steps Per Unit (steps/mm)
* Override with M92
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 400, 92.60 }
/**
* Default Max Feed Rate (mm/s)
* Override with M203
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_FEEDRATE { 500, 500, 5, 25 }
@ -663,7 +667,7 @@
* Default Max Acceleration (change/s) change = mm/s
* (Maximum start speed for accelerated moves)
* Override with M201
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_ACCELERATION { 500, 500, 100, 5000 }
@ -902,6 +906,7 @@
#define INVERT_E2_DIR false
#define INVERT_E3_DIR false
#define INVERT_E4_DIR false
#define INVERT_E5_DIR false
// @section homing

15
Marlin/src/config/examples/Creality/CR-8/Configuration_adv.h

@ -242,6 +242,7 @@
#define E2_AUTO_FAN_PIN -1
#define E3_AUTO_FAN_PIN -1
#define E4_AUTO_FAN_PIN -1
#define E5_AUTO_FAN_PIN -1
#define CHAMBER_AUTO_FAN_PIN -1
#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed
@ -482,7 +483,7 @@
//#define ADAPTIVE_STEP_SMOOTHING
// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU.
#define MICROSTEP_MODES { 16, 16, 16, 16, 16 } // [1,2,4,8,16]
#define MICROSTEP_MODES { 16, 16, 16, 16, 16, 16 } // [1,2,4,8,16]
/**
* @section stepper motor current
@ -1122,6 +1123,10 @@
#define E4_SENSE_RESISTOR 91
#define E4_MICROSTEPS 16
#define E5_MAX_CURRENT 1000
#define E5_SENSE_RESISTOR 91
#define E5_MICROSTEPS 16
#endif // TMC26X
// @section tmc_smart
@ -1186,6 +1191,9 @@
#define E4_CURRENT 800
#define E4_MICROSTEPS 16
#define E5_CURRENT 800
#define E5_MICROSTEPS 16
/**
* Use software SPI for TMC2130.
* The default SW SPI pins are defined the respective pins files,
@ -1241,6 +1249,7 @@
#define E2_HYBRID_THRESHOLD 30
#define E3_HYBRID_THRESHOLD 30
#define E4_HYBRID_THRESHOLD 30
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
@ -1358,6 +1367,10 @@
#define E4_OVERCURRENT 2000
#define E4_STALLCURRENT 1500
#define E5_MICROSTEPS 16
#define E5_OVERCURRENT 2000
#define E5_STALLCURRENT 1500
#endif // L6470
/**

11
Marlin/src/config/examples/Creality/Ender-2/Configuration.h

@ -333,6 +333,7 @@
#define TEMP_SENSOR_2 0
#define TEMP_SENSOR_3 0
#define TEMP_SENSOR_4 0
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0
@ -363,6 +364,7 @@
#define HEATER_2_MINTEMP 5
#define HEATER_3_MINTEMP 5
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off.
@ -373,6 +375,7 @@
#define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 125
//===========================================================================
@ -597,6 +600,7 @@
//#define E2_DRIVER_TYPE A4988
//#define E3_DRIVER_TYPE A4988
//#define E4_DRIVER_TYPE A4988
//#define E5_DRIVER_TYPE A4988
// Enable this feature if all enabled endstop pins are interrupt-capable.
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
@ -642,14 +646,14 @@
/**
* Default Axis Steps Per Unit (steps/mm)
* Override with M92
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 400, 93 }
/**
* Default Max Feed Rate (mm/s)
* Override with M203
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_FEEDRATE { 500, 500, 5, 25 }
@ -657,7 +661,7 @@
* Default Max Acceleration (change/s) change = mm/s
* (Maximum start speed for accelerated moves)
* Override with M201
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_ACCELERATION { 500, 500, 100, 5000 }
@ -896,6 +900,7 @@
#define INVERT_E2_DIR false
#define INVERT_E3_DIR false
#define INVERT_E4_DIR false
#define INVERT_E5_DIR false
// @section homing

15
Marlin/src/config/examples/Creality/Ender-2/Configuration_adv.h

@ -242,6 +242,7 @@
#define E2_AUTO_FAN_PIN -1
#define E3_AUTO_FAN_PIN -1
#define E4_AUTO_FAN_PIN -1
#define E5_AUTO_FAN_PIN -1
#define CHAMBER_AUTO_FAN_PIN -1
#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed
@ -482,7 +483,7 @@
//#define ADAPTIVE_STEP_SMOOTHING
// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU.
#define MICROSTEP_MODES { 16, 16, 16, 16, 16 } // [1,2,4,8,16]
#define MICROSTEP_MODES { 16, 16, 16, 16, 16, 16 } // [1,2,4,8,16]
/**
* @section stepper motor current
@ -1122,6 +1123,10 @@
#define E4_SENSE_RESISTOR 91
#define E4_MICROSTEPS 16
#define E5_MAX_CURRENT 1000
#define E5_SENSE_RESISTOR 91
#define E5_MICROSTEPS 16
#endif // TMC26X
// @section tmc_smart
@ -1186,6 +1191,9 @@
#define E4_CURRENT 800
#define E4_MICROSTEPS 16
#define E5_CURRENT 800
#define E5_MICROSTEPS 16
/**
* Use software SPI for TMC2130.
* The default SW SPI pins are defined the respective pins files,
@ -1241,6 +1249,7 @@
#define E2_HYBRID_THRESHOLD 30
#define E3_HYBRID_THRESHOLD 30
#define E4_HYBRID_THRESHOLD 30
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
@ -1358,6 +1367,10 @@
#define E4_OVERCURRENT 2000
#define E4_STALLCURRENT 1500
#define E5_MICROSTEPS 16
#define E5_OVERCURRENT 2000
#define E5_STALLCURRENT 1500
#endif // L6470
/**

11
Marlin/src/config/examples/Creality/Ender-3/Configuration.h

@ -333,6 +333,7 @@
#define TEMP_SENSOR_2 0
#define TEMP_SENSOR_3 0
#define TEMP_SENSOR_4 0
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0
@ -363,6 +364,7 @@
#define HEATER_2_MINTEMP 5
#define HEATER_3_MINTEMP 5
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off.
@ -373,6 +375,7 @@
#define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 125
//===========================================================================
@ -597,6 +600,7 @@
//#define E2_DRIVER_TYPE A4988
//#define E3_DRIVER_TYPE A4988
//#define E4_DRIVER_TYPE A4988
//#define E5_DRIVER_TYPE A4988
// Enable this feature if all enabled endstop pins are interrupt-capable.
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
@ -642,14 +646,14 @@
/**
* Default Axis Steps Per Unit (steps/mm)
* Override with M92
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 400, 93 }
/**
* Default Max Feed Rate (mm/s)
* Override with M203
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_FEEDRATE { 500, 500, 5, 25 }
@ -657,7 +661,7 @@
* Default Max Acceleration (change/s) change = mm/s
* (Maximum start speed for accelerated moves)
* Override with M201
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_ACCELERATION { 500, 500, 100, 5000 }
@ -896,6 +900,7 @@
#define INVERT_E2_DIR false
#define INVERT_E3_DIR false
#define INVERT_E4_DIR false
#define INVERT_E5_DIR false
// @section homing

15
Marlin/src/config/examples/Creality/Ender-3/Configuration_adv.h

@ -242,6 +242,7 @@
#define E2_AUTO_FAN_PIN -1
#define E3_AUTO_FAN_PIN -1
#define E4_AUTO_FAN_PIN -1
#define E5_AUTO_FAN_PIN -1
#define CHAMBER_AUTO_FAN_PIN -1
#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed
@ -482,7 +483,7 @@
//#define ADAPTIVE_STEP_SMOOTHING
// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU.
#define MICROSTEP_MODES { 16, 16, 16, 16, 16 } // [1,2,4,8,16]
#define MICROSTEP_MODES { 16, 16, 16, 16, 16, 16 } // [1,2,4,8,16]
/**
* @section stepper motor current
@ -1122,6 +1123,10 @@
#define E4_SENSE_RESISTOR 91
#define E4_MICROSTEPS 16
#define E5_MAX_CURRENT 1000
#define E5_SENSE_RESISTOR 91
#define E5_MICROSTEPS 16
#endif // TMC26X
// @section tmc_smart
@ -1186,6 +1191,9 @@
#define E4_CURRENT 800
#define E4_MICROSTEPS 16
#define E5_CURRENT 800
#define E5_MICROSTEPS 16
/**
* Use software SPI for TMC2130.
* The default SW SPI pins are defined the respective pins files,
@ -1241,6 +1249,7 @@
#define E2_HYBRID_THRESHOLD 30
#define E3_HYBRID_THRESHOLD 30
#define E4_HYBRID_THRESHOLD 30
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
@ -1358,6 +1367,10 @@
#define E4_OVERCURRENT 2000
#define E4_STALLCURRENT 1500
#define E5_MICROSTEPS 16
#define E5_OVERCURRENT 2000
#define E5_STALLCURRENT 1500
#endif // L6470
/**

11
Marlin/src/config/examples/Creality/Ender-4/Configuration.h

@ -333,6 +333,7 @@
#define TEMP_SENSOR_2 0
#define TEMP_SENSOR_3 0
#define TEMP_SENSOR_4 0
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0
@ -363,6 +364,7 @@
#define HEATER_2_MINTEMP 5
#define HEATER_3_MINTEMP 5
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off.
@ -373,6 +375,7 @@
#define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
//===========================================================================
@ -603,6 +606,7 @@
//#define E2_DRIVER_TYPE A4988
//#define E3_DRIVER_TYPE A4988
//#define E4_DRIVER_TYPE A4988
//#define E5_DRIVER_TYPE A4988
// Enable this feature if all enabled endstop pins are interrupt-capable.
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
@ -648,14 +652,14 @@
/**
* Default Axis Steps Per Unit (steps/mm)
* Override with M92
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 400, 110 }
/**
* Default Max Feed Rate (mm/s)
* Override with M203
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_FEEDRATE { 300, 300, 10, 25 }
@ -663,7 +667,7 @@
* Default Max Acceleration (change/s) change = mm/s
* (Maximum start speed for accelerated moves)
* Override with M201
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_ACCELERATION { 500, 500, 100, 5000 }
@ -902,6 +906,7 @@
#define INVERT_E2_DIR false
#define INVERT_E3_DIR false
#define INVERT_E4_DIR false
#define INVERT_E5_DIR false
// @section homing

15
Marlin/src/config/examples/Creality/Ender-4/Configuration_adv.h

@ -242,6 +242,7 @@
#define E2_AUTO_FAN_PIN -1
#define E3_AUTO_FAN_PIN -1
#define E4_AUTO_FAN_PIN -1
#define E5_AUTO_FAN_PIN -1
#define CHAMBER_AUTO_FAN_PIN -1
#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed
@ -482,7 +483,7 @@
//#define ADAPTIVE_STEP_SMOOTHING
// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU.
#define MICROSTEP_MODES { 16, 16, 16, 16, 16 } // [1,2,4,8,16]
#define MICROSTEP_MODES { 16, 16, 16, 16, 16, 16 } // [1,2,4,8,16]
/**
* @section stepper motor current
@ -1122,6 +1123,10 @@
#define E4_SENSE_RESISTOR 91
#define E4_MICROSTEPS 16
#define E5_MAX_CURRENT 1000
#define E5_SENSE_RESISTOR 91
#define E5_MICROSTEPS 16
#endif // TMC26X
// @section tmc_smart
@ -1186,6 +1191,9 @@
#define E4_CURRENT 800
#define E4_MICROSTEPS 16
#define E5_CURRENT 800
#define E5_MICROSTEPS 16
/**
* Use software SPI for TMC2130.
* The default SW SPI pins are defined the respective pins files,
@ -1241,6 +1249,7 @@
#define E2_HYBRID_THRESHOLD 30
#define E3_HYBRID_THRESHOLD 30
#define E4_HYBRID_THRESHOLD 30
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
@ -1358,6 +1367,10 @@
#define E4_OVERCURRENT 2000
#define E4_STALLCURRENT 1500
#define E5_MICROSTEPS 16
#define E5_OVERCURRENT 2000
#define E5_STALLCURRENT 1500
#endif // L6470
/**

11
Marlin/src/config/examples/Einstart-S/Configuration.h

@ -335,6 +335,7 @@
#define TEMP_SENSOR_2 0
#define TEMP_SENSOR_3 0
#define TEMP_SENSOR_4 0
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 0
#define TEMP_SENSOR_CHAMBER 0
@ -365,6 +366,7 @@
#define HEATER_2_MINTEMP 5
#define HEATER_3_MINTEMP 5
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off.
@ -375,6 +377,7 @@
#define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
//===========================================================================
@ -605,6 +608,7 @@
//#define E2_DRIVER_TYPE A4988
//#define E3_DRIVER_TYPE A4988
//#define E4_DRIVER_TYPE A4988
//#define E5_DRIVER_TYPE A4988
// Enable this feature if all enabled endstop pins are interrupt-capable.
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
@ -650,14 +654,14 @@
/**
* Default Axis Steps Per Unit (steps/mm)
* Override with M92
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 80, 96.337120 }
/**
* Default Max Feed Rate (mm/s)
* Override with M203
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_FEEDRATE { 300, 300, 5, 25 }
@ -665,7 +669,7 @@
* Default Max Acceleration (change/s) change = mm/s
* (Maximum start speed for accelerated moves)
* Override with M201
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_ACCELERATION { 2000, 2000, 100, 10000 }
@ -902,6 +906,7 @@
#define INVERT_E2_DIR false
#define INVERT_E3_DIR false
#define INVERT_E4_DIR false
#define INVERT_E5_DIR false
// @section homing

15
Marlin/src/config/examples/Einstart-S/Configuration_adv.h

@ -242,6 +242,7 @@
#define E2_AUTO_FAN_PIN -1
#define E3_AUTO_FAN_PIN -1
#define E4_AUTO_FAN_PIN -1
#define E5_AUTO_FAN_PIN -1
#define CHAMBER_AUTO_FAN_PIN -1
#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed
@ -482,7 +483,7 @@
//#define ADAPTIVE_STEP_SMOOTHING
// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU.
#define MICROSTEP_MODES { 16, 16, 16, 16, 16 } // [1,2,4,8,16]
#define MICROSTEP_MODES { 16, 16, 16, 16, 16, 16 } // [1,2,4,8,16]
/**
* @section stepper motor current
@ -1122,6 +1123,10 @@
#define E4_SENSE_RESISTOR 91
#define E4_MICROSTEPS 16
#define E5_MAX_CURRENT 1000
#define E5_SENSE_RESISTOR 91
#define E5_MICROSTEPS 16
#endif // TMC26X
// @section tmc_smart
@ -1186,6 +1191,9 @@
#define E4_CURRENT 800
#define E4_MICROSTEPS 16
#define E5_CURRENT 800
#define E5_MICROSTEPS 16
/**
* Use software SPI for TMC2130.
* The default SW SPI pins are defined the respective pins files,
@ -1241,6 +1249,7 @@
#define E2_HYBRID_THRESHOLD 30
#define E3_HYBRID_THRESHOLD 30
#define E4_HYBRID_THRESHOLD 30
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
@ -1358,6 +1367,10 @@
#define E4_OVERCURRENT 2000
#define E4_STALLCURRENT 1500
#define E5_MICROSTEPS 16
#define E5_OVERCURRENT 2000
#define E5_STALLCURRENT 1500
#endif // L6470
/**

11
Marlin/src/config/examples/Felix/Configuration.h

@ -333,6 +333,7 @@
#define TEMP_SENSOR_2 0
#define TEMP_SENSOR_3 0
#define TEMP_SENSOR_4 0
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0
@ -363,6 +364,7 @@
#define HEATER_2_MINTEMP 5
#define HEATER_3_MINTEMP 5
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off.
@ -373,6 +375,7 @@
#define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
//===========================================================================
@ -574,6 +577,7 @@
//#define E2_DRIVER_TYPE A4988
//#define E3_DRIVER_TYPE A4988
//#define E4_DRIVER_TYPE A4988
//#define E5_DRIVER_TYPE A4988
// Enable this feature if all enabled endstop pins are interrupt-capable.
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
@ -620,14 +624,14 @@
/**
* Default Axis Steps Per Unit (steps/mm)
* Override with M92
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT { 76.190476, 76.190476, 1600, 164 }
/**
* Default Max Feed Rate (mm/s)
* Override with M203
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_FEEDRATE { 500, 500, 5, 25 }
@ -635,7 +639,7 @@
* Default Max Acceleration (change/s) change = mm/s
* (Maximum start speed for accelerated moves)
* Override with M201
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_ACCELERATION { 5000, 5000, 100, 80000 }
@ -874,6 +878,7 @@
#define INVERT_E2_DIR false
#define INVERT_E3_DIR false
#define INVERT_E4_DIR false
#define INVERT_E5_DIR false
// @section homing

15
Marlin/src/config/examples/Felix/Configuration_adv.h

@ -242,6 +242,7 @@
#define E2_AUTO_FAN_PIN -1
#define E3_AUTO_FAN_PIN -1
#define E4_AUTO_FAN_PIN -1
#define E5_AUTO_FAN_PIN -1
#define CHAMBER_AUTO_FAN_PIN -1
#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed
@ -482,7 +483,7 @@
//#define ADAPTIVE_STEP_SMOOTHING
// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU.
#define MICROSTEP_MODES { 16, 16, 16, 16, 16 } // [1,2,4,8,16]
#define MICROSTEP_MODES { 16, 16, 16, 16, 16, 16 } // [1,2,4,8,16]
/**
* @section stepper motor current
@ -1122,6 +1123,10 @@
#define E4_SENSE_RESISTOR 91
#define E4_MICROSTEPS 16
#define E5_MAX_CURRENT 1000
#define E5_SENSE_RESISTOR 91
#define E5_MICROSTEPS 16
#endif // TMC26X
// @section tmc_smart
@ -1186,6 +1191,9 @@
#define E4_CURRENT 800
#define E4_MICROSTEPS 16
#define E5_CURRENT 800
#define E5_MICROSTEPS 16
/**
* Use software SPI for TMC2130.
* The default SW SPI pins are defined the respective pins files,
@ -1241,6 +1249,7 @@
#define E2_HYBRID_THRESHOLD 30
#define E3_HYBRID_THRESHOLD 30
#define E4_HYBRID_THRESHOLD 30
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
@ -1358,6 +1367,10 @@
#define E4_OVERCURRENT 2000
#define E4_STALLCURRENT 1500
#define E5_MICROSTEPS 16
#define E5_OVERCURRENT 2000
#define E5_STALLCURRENT 1500
#endif // L6470
/**

11
Marlin/src/config/examples/Felix/DUAL/Configuration.h

@ -333,6 +333,7 @@
#define TEMP_SENSOR_2 0
#define TEMP_SENSOR_3 0
#define TEMP_SENSOR_4 0
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0
@ -363,6 +364,7 @@
#define HEATER_2_MINTEMP 5
#define HEATER_3_MINTEMP 5
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off.
@ -373,6 +375,7 @@
#define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
//===========================================================================
@ -574,6 +577,7 @@
//#define E2_DRIVER_TYPE A4988
//#define E3_DRIVER_TYPE A4988
//#define E4_DRIVER_TYPE A4988
//#define E5_DRIVER_TYPE A4988
// Enable this feature if all enabled endstop pins are interrupt-capable.
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
@ -620,14 +624,14 @@
/**
* Default Axis Steps Per Unit (steps/mm)
* Override with M92
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT { 76.190476, 76.190476, 1600, 164 }
/**
* Default Max Feed Rate (mm/s)
* Override with M203
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_FEEDRATE { 500, 500, 5, 25 }
@ -635,7 +639,7 @@
* Default Max Acceleration (change/s) change = mm/s
* (Maximum start speed for accelerated moves)
* Override with M201
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_ACCELERATION { 5000, 5000, 100, 80000 }
@ -874,6 +878,7 @@
#define INVERT_E2_DIR false
#define INVERT_E3_DIR false
#define INVERT_E4_DIR false
#define INVERT_E5_DIR false
// @section homing

11
Marlin/src/config/examples/FolgerTech/i3-2020/Configuration.h

@ -333,6 +333,7 @@
#define TEMP_SENSOR_2 0
#define TEMP_SENSOR_3 0
#define TEMP_SENSOR_4 0
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0
@ -363,6 +364,7 @@
#define HEATER_2_MINTEMP 5
#define HEATER_3_MINTEMP 5
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off.
@ -373,6 +375,7 @@
#define HEATER_2_MAXTEMP 245
#define HEATER_3_MAXTEMP 245
#define HEATER_4_MAXTEMP 245
#define HEATER_5_MAXTEMP 245
#define BED_MAXTEMP 115
//===========================================================================
@ -598,6 +601,7 @@
//#define E2_DRIVER_TYPE A4988
//#define E3_DRIVER_TYPE A4988
//#define E4_DRIVER_TYPE A4988
//#define E5_DRIVER_TYPE A4988
// Enable this feature if all enabled endstop pins are interrupt-capable.
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
@ -643,7 +647,7 @@
/**
* Default Axis Steps Per Unit (steps/mm)
* Override with M92
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
//#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 4000, 52.2 } // 52.4 is correct for printer as shipped
#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 4000, 104.4 } // 104.4 with 32 micro steps enabled gives better results
@ -651,7 +655,7 @@
/**
* Default Max Feed Rate (mm/s)
* Override with M203
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_FEEDRATE { 250, 250, 2, 17 }
@ -659,7 +663,7 @@
* Default Max Acceleration (change/s) change = mm/s
* (Maximum start speed for accelerated moves)
* Override with M201
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_ACCELERATION { 1000, 1000, 4, 750 }
@ -898,6 +902,7 @@
#define INVERT_E2_DIR false
#define INVERT_E3_DIR false
#define INVERT_E4_DIR false
#define INVERT_E5_DIR false
// @section homing

15
Marlin/src/config/examples/FolgerTech/i3-2020/Configuration_adv.h

@ -242,6 +242,7 @@
#define E2_AUTO_FAN_PIN -1
#define E3_AUTO_FAN_PIN -1
#define E4_AUTO_FAN_PIN -1
#define E5_AUTO_FAN_PIN -1
#define CHAMBER_AUTO_FAN_PIN -1
#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed
@ -482,7 +483,7 @@
//#define ADAPTIVE_STEP_SMOOTHING
// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU.
#define MICROSTEP_MODES { 16, 16, 16, 16, 16 } // [1,2,4,8,16]
#define MICROSTEP_MODES { 16, 16, 16, 16, 16, 16 } // [1,2,4,8,16]
/**
* @section stepper motor current
@ -1122,6 +1123,10 @@
#define E4_SENSE_RESISTOR 91
#define E4_MICROSTEPS 16
#define E5_MAX_CURRENT 1000
#define E5_SENSE_RESISTOR 91
#define E5_MICROSTEPS 16
#endif // TMC26X
// @section tmc_smart
@ -1186,6 +1191,9 @@
#define E4_CURRENT 800
#define E4_MICROSTEPS 16
#define E5_CURRENT 800
#define E5_MICROSTEPS 16
/**
* Use software SPI for TMC2130.
* The default SW SPI pins are defined the respective pins files,
@ -1241,6 +1249,7 @@
#define E2_HYBRID_THRESHOLD 30
#define E3_HYBRID_THRESHOLD 30
#define E4_HYBRID_THRESHOLD 30
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
@ -1358,6 +1367,10 @@
#define E4_OVERCURRENT 2000
#define E4_STALLCURRENT 1500
#define E5_MICROSTEPS 16
#define E5_OVERCURRENT 2000
#define E5_STALLCURRENT 1500
#endif // L6470
/**

11
Marlin/src/config/examples/Formbot/T-Rex_2+/Configuration.h

@ -326,6 +326,7 @@
#define TEMP_SENSOR_2 0
#define TEMP_SENSOR_3 0
#define TEMP_SENSOR_4 0
#define TEMP_SENSOR_5 0
#if(ENABLED(ROXYs_TRex))
#define TEMP_SENSOR_BED 11
@ -362,6 +363,7 @@
#define HEATER_2_MINTEMP 5
#define HEATER_3_MINTEMP 5
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off.
@ -372,6 +374,7 @@
#define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
//===========================================================================
@ -606,6 +609,7 @@
//#define E2_DRIVER_TYPE A4988
//#define E3_DRIVER_TYPE A4988
//#define E4_DRIVER_TYPE A4988
//#define E5_DRIVER_TYPE A4988
// Enable this feature if all enabled endstop pins are interrupt-capable.
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
@ -651,7 +655,7 @@
/**
* Default Axis Steps Per Unit (steps/mm)
* Override with M92
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
//#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 160, 1600, 93 }
#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 800, 93 }
@ -659,7 +663,7 @@
/**
* Default Max Feed Rate (mm/s)
* Override with M203
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
//#define DEFAULT_MAX_FEEDRATE { 250, 150, 5, 25 }
#define DEFAULT_MAX_FEEDRATE { 250, 100, 5, 25 }
@ -668,7 +672,7 @@
* Default Max Acceleration (change/s) change = mm/s
* (Maximum start speed for accelerated moves)
* Override with M201
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_ACCELERATION { 1500, 500, 400, 4000 }
@ -918,6 +922,7 @@
#define INVERT_E2_DIR false
#define INVERT_E3_DIR false
#define INVERT_E4_DIR false
#define INVERT_E5_DIR false
// @section homing

15
Marlin/src/config/examples/Formbot/T-Rex_2+/Configuration_adv.h

@ -242,6 +242,7 @@
#define E2_AUTO_FAN_PIN -1
#define E3_AUTO_FAN_PIN -1
#define E4_AUTO_FAN_PIN -1
#define E5_AUTO_FAN_PIN -1
#define CHAMBER_AUTO_FAN_PIN -1
#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed
@ -486,7 +487,7 @@
//#define ADAPTIVE_STEP_SMOOTHING
// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU.
#define MICROSTEP_MODES { 16, 16, 16, 16, 16 } // [1,2,4,8,16]
#define MICROSTEP_MODES { 16, 16, 16, 16, 16, 16 } // [1,2,4,8,16]
/**
* @section stepper motor current
@ -1122,6 +1123,10 @@
#define E4_SENSE_RESISTOR 91
#define E4_MICROSTEPS 16
#define E5_MAX_CURRENT 1000
#define E5_SENSE_RESISTOR 91
#define E5_MICROSTEPS 16
#endif // TMC26X
// @section tmc_smart
@ -1183,6 +1188,9 @@
#define E4_CURRENT 800
#define E4_MICROSTEPS 16
#define E5_CURRENT 800
#define E5_MICROSTEPS 16
/**
* Use software SPI for TMC2130.
* The default SW SPI pins are defined the respective pins files,
@ -1238,6 +1246,7 @@
#define E2_HYBRID_THRESHOLD 30
#define E3_HYBRID_THRESHOLD 30
#define E4_HYBRID_THRESHOLD 30
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
@ -1355,6 +1364,10 @@
#define E4_OVERCURRENT 2000
#define E4_STALLCURRENT 1500
#define E5_MICROSTEPS 16
#define E5_OVERCURRENT 2000
#define E5_STALLCURRENT 1500
#endif // L6470
/**

11
Marlin/src/config/examples/Formbot/T_Rex_3/Configuration.h

@ -330,6 +330,7 @@
#define TEMP_SENSOR_2 0
#define TEMP_SENSOR_3 0
#define TEMP_SENSOR_4 0
#define TEMP_SENSOR_5 0
#if(ENABLED(ROXYs_TRex))
#define TEMP_SENSOR_BED 11
@ -372,6 +373,7 @@
#define HEATER_2_MINTEMP 5
#define HEATER_3_MINTEMP 5
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off.
@ -382,6 +384,7 @@
#define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
//===========================================================================
@ -616,6 +619,7 @@
//#define E2_DRIVER_TYPE A4988
//#define E3_DRIVER_TYPE A4988
//#define E4_DRIVER_TYPE A4988
//#define E5_DRIVER_TYPE A4988
// Enable this feature if all enabled endstop pins are interrupt-capable.
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
@ -661,7 +665,7 @@
/**
* Default Axis Steps Per Unit (steps/mm)
* Override with M92
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
//#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 160, 1600, 93 }
#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 800, 93 }
@ -669,7 +673,7 @@
/**
* Default Max Feed Rate (mm/s)
* Override with M203
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
//#define DEFAULT_MAX_FEEDRATE { 250, 150, 5, 25 }
#define DEFAULT_MAX_FEEDRATE { 250, 100, 5, 25 }
@ -678,7 +682,7 @@
* Default Max Acceleration (change/s) change = mm/s
* (Maximum start speed for accelerated moves)
* Override with M201
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_ACCELERATION { 1500, 500, 400, 4000 }
@ -928,6 +932,7 @@
#define INVERT_E2_DIR false
#define INVERT_E3_DIR false
#define INVERT_E4_DIR false
#define INVERT_E5_DIR false
// @section homing

15
Marlin/src/config/examples/Formbot/T_Rex_3/Configuration_adv.h

@ -242,6 +242,7 @@
#define E2_AUTO_FAN_PIN -1
#define E3_AUTO_FAN_PIN -1
#define E4_AUTO_FAN_PIN -1
#define E5_AUTO_FAN_PIN -1
#define CHAMBER_AUTO_FAN_PIN -1
#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed
@ -488,7 +489,7 @@
//#define ADAPTIVE_STEP_SMOOTHING
// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU.
#define MICROSTEP_MODES { 16, 16, 16, 16, 16 } // [1,2,4,8,16]
#define MICROSTEP_MODES { 16, 16, 16, 16, 16, 16 } // [1,2,4,8,16]
/**
* @section stepper motor current
@ -1123,6 +1124,10 @@
#define E4_SENSE_RESISTOR 91
#define E4_MICROSTEPS 16
#define E5_MAX_CURRENT 1000
#define E5_SENSE_RESISTOR 91
#define E5_MICROSTEPS 16
#endif // TMC26X
// @section tmc_smart
@ -1184,6 +1189,9 @@
#define E4_CURRENT 800
#define E4_MICROSTEPS 16
#define E5_CURRENT 800
#define E5_MICROSTEPS 16
/**
* Use software SPI for TMC2130.
* The default SW SPI pins are defined the respective pins files,
@ -1239,6 +1247,7 @@
#define E2_HYBRID_THRESHOLD 30
#define E3_HYBRID_THRESHOLD 30
#define E4_HYBRID_THRESHOLD 30
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
@ -1356,6 +1365,10 @@
#define E4_OVERCURRENT 2000
#define E4_STALLCURRENT 1500
#define E5_MICROSTEPS 16
#define E5_OVERCURRENT 2000
#define E5_STALLCURRENT 1500
#endif // L6470
/**

11
Marlin/src/config/examples/Geeetech/GT2560/Configuration.h

@ -333,6 +333,7 @@
#define TEMP_SENSOR_2 0
#define TEMP_SENSOR_3 0
#define TEMP_SENSOR_4 0
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0
@ -363,6 +364,7 @@
#define HEATER_2_MINTEMP 5
#define HEATER_3_MINTEMP 5
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off.
@ -373,6 +375,7 @@
#define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
//===========================================================================
@ -608,6 +611,7 @@
//#define E2_DRIVER_TYPE A4988
//#define E3_DRIVER_TYPE A4988
//#define E4_DRIVER_TYPE A4988
//#define E5_DRIVER_TYPE A4988
// Enable this feature if all enabled endstop pins are interrupt-capable.
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
@ -653,14 +657,14 @@
/**
* Default Axis Steps Per Unit (steps/mm)
* Override with M92
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT { 78.74, 78.74, 2560, 105 }
/**
* Default Max Feed Rate (mm/s)
* Override with M203
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_FEEDRATE { 400, 400, 2, 45 }
@ -668,7 +672,7 @@
* Default Max Acceleration (change/s) change = mm/s
* (Maximum start speed for accelerated moves)
* Override with M201
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_ACCELERATION { 5000, 5000, 50, 5000 }
@ -907,6 +911,7 @@
#define INVERT_E2_DIR true
#define INVERT_E3_DIR true
#define INVERT_E4_DIR true
#define INVERT_E5_DIR true
// @section homing

11
Marlin/src/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h

@ -333,6 +333,7 @@
#define TEMP_SENSOR_2 0
#define TEMP_SENSOR_3 0
#define TEMP_SENSOR_4 0
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0
@ -363,6 +364,7 @@
#define HEATER_2_MINTEMP 5
#define HEATER_3_MINTEMP 5
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off.
@ -373,6 +375,7 @@
#define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
//===========================================================================
@ -593,6 +596,7 @@
//#define E2_DRIVER_TYPE A4988
//#define E3_DRIVER_TYPE A4988
//#define E4_DRIVER_TYPE A4988
//#define E5_DRIVER_TYPE A4988
// Enable this feature if all enabled endstop pins are interrupt-capable.
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
@ -638,14 +642,14 @@
/**
* Default Axis Steps Per Unit (steps/mm)
* Override with M92
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 2560, 93 } // MXL, Z M8=1.25, MK8
/**
* Default Max Feed Rate (mm/s)
* Override with M203
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_FEEDRATE { 400, 400, 2, 45 }
@ -653,7 +657,7 @@
* Default Max Acceleration (change/s) change = mm/s
* (Maximum start speed for accelerated moves)
* Override with M201
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_ACCELERATION { 4000, 4000, 40, 4000 }
@ -892,6 +896,7 @@
#define INVERT_E2_DIR false
#define INVERT_E3_DIR false
#define INVERT_E4_DIR false
#define INVERT_E5_DIR false
// @section homing

11
Marlin/src/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h

@ -333,6 +333,7 @@
#define TEMP_SENSOR_2 0
#define TEMP_SENSOR_3 0
#define TEMP_SENSOR_4 0
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0
@ -363,6 +364,7 @@
#define HEATER_2_MINTEMP 5
#define HEATER_3_MINTEMP 5
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off.
@ -373,6 +375,7 @@
#define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 125
//===========================================================================
@ -608,6 +611,7 @@
//#define E2_DRIVER_TYPE A4988
//#define E3_DRIVER_TYPE A4988
//#define E4_DRIVER_TYPE A4988
//#define E5_DRIVER_TYPE A4988
// Enable this feature if all enabled endstop pins are interrupt-capable.
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
@ -653,14 +657,14 @@
/**
* Default Axis Steps Per Unit (steps/mm)
* Override with M92
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT { 78.74, 78.74, 2560, 105 }
/**
* Default Max Feed Rate (mm/s)
* Override with M203
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_FEEDRATE { 400, 400, 2, 45 }
@ -668,7 +672,7 @@
* Default Max Acceleration (change/s) change = mm/s
* (Maximum start speed for accelerated moves)
* Override with M201
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_ACCELERATION { 5000, 5000, 75, 5000 }
@ -908,6 +912,7 @@
#define INVERT_E2_DIR true
#define INVERT_E3_DIR true
#define INVERT_E4_DIR true
#define INVERT_E5_DIR true
// @section homing

11
Marlin/src/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h

@ -333,6 +333,7 @@
#define TEMP_SENSOR_2 0
#define TEMP_SENSOR_3 0
#define TEMP_SENSOR_4 0
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0
@ -363,6 +364,7 @@
#define HEATER_2_MINTEMP 5
#define HEATER_3_MINTEMP 5
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off.
@ -373,6 +375,7 @@
#define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 125
//===========================================================================
@ -608,6 +611,7 @@
//#define E2_DRIVER_TYPE A4988
//#define E3_DRIVER_TYPE A4988
//#define E4_DRIVER_TYPE A4988
//#define E5_DRIVER_TYPE A4988
// Enable this feature if all enabled endstop pins are interrupt-capable.
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
@ -653,14 +657,14 @@
/**
* Default Axis Steps Per Unit (steps/mm)
* Override with M92
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT { 78.74, 78.74, 2560, 105 }
/**
* Default Max Feed Rate (mm/s)
* Override with M203
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_FEEDRATE { 400, 400, 2, 45 }
@ -668,7 +672,7 @@
* Default Max Acceleration (change/s) change = mm/s
* (Maximum start speed for accelerated moves)
* Override with M201
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_ACCELERATION { 5000, 5000, 75, 5000 }
@ -907,6 +911,7 @@
#define INVERT_E2_DIR true
#define INVERT_E3_DIR true
#define INVERT_E4_DIR true
#define INVERT_E5_DIR true
// @section homing

11
Marlin/src/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h

@ -333,6 +333,7 @@
#define TEMP_SENSOR_2 0
#define TEMP_SENSOR_3 0
#define TEMP_SENSOR_4 0
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0
@ -363,6 +364,7 @@
#define HEATER_2_MINTEMP 5
#define HEATER_3_MINTEMP 5
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off.
@ -373,6 +375,7 @@
#define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
//===========================================================================
@ -593,6 +596,7 @@
//#define E2_DRIVER_TYPE A4988
//#define E3_DRIVER_TYPE A4988
//#define E4_DRIVER_TYPE A4988
//#define E5_DRIVER_TYPE A4988
// Enable this feature if all enabled endstop pins are interrupt-capable.
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
@ -638,14 +642,14 @@
/**
* Default Axis Steps Per Unit (steps/mm)
* Override with M92
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 2560, 95, 95 }
/**
* Default Max Feed Rate (mm/s)
* Override with M203
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_FEEDRATE { 300, 300, 5, 25 }
@ -653,7 +657,7 @@
* Default Max Acceleration (change/s) change = mm/s
* (Maximum start speed for accelerated moves)
* Override with M201
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_ACCELERATION { 3000, 3000, 100, 10000 }
@ -892,6 +896,7 @@
#define INVERT_E2_DIR false
#define INVERT_E3_DIR false
#define INVERT_E4_DIR false
#define INVERT_E5_DIR false
// @section homing

15
Marlin/src/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h

@ -242,6 +242,7 @@
#define E2_AUTO_FAN_PIN -1
#define E3_AUTO_FAN_PIN -1
#define E4_AUTO_FAN_PIN -1
#define E5_AUTO_FAN_PIN -1
#define CHAMBER_AUTO_FAN_PIN -1
#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed
@ -482,7 +483,7 @@
//#define ADAPTIVE_STEP_SMOOTHING
// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU.
#define MICROSTEP_MODES { 16, 16, 16, 16, 16 } // [1,2,4,8,16]
#define MICROSTEP_MODES { 16, 16, 16, 16, 16, 16 } // [1,2,4,8,16]
/**
* @section stepper motor current
@ -1122,6 +1123,10 @@
#define E4_SENSE_RESISTOR 91
#define E4_MICROSTEPS 16
#define E5_MAX_CURRENT 1000
#define E5_SENSE_RESISTOR 91
#define E5_MICROSTEPS 16
#endif // TMC26X
// @section tmc_smart
@ -1186,6 +1191,9 @@
#define E4_CURRENT 800
#define E4_MICROSTEPS 16
#define E5_CURRENT 800
#define E5_MICROSTEPS 16
/**
* Use software SPI for TMC2130.
* The default SW SPI pins are defined the respective pins files,
@ -1241,6 +1249,7 @@
#define E2_HYBRID_THRESHOLD 30
#define E3_HYBRID_THRESHOLD 30
#define E4_HYBRID_THRESHOLD 30
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
@ -1358,6 +1367,10 @@
#define E4_OVERCURRENT 2000
#define E4_STALLCURRENT 1500
#define E5_MICROSTEPS 16
#define E5_OVERCURRENT 2000
#define E5_STALLCURRENT 1500
#endif // L6470
/**

11
Marlin/src/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h

@ -333,6 +333,7 @@
#define TEMP_SENSOR_2 0
#define TEMP_SENSOR_3 0
#define TEMP_SENSOR_4 0
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0
@ -363,6 +364,7 @@
#define HEATER_2_MINTEMP 5
#define HEATER_3_MINTEMP 5
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off.
@ -373,6 +375,7 @@
#define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
//===========================================================================
@ -593,6 +596,7 @@
//#define E2_DRIVER_TYPE A4988
//#define E3_DRIVER_TYPE A4988
//#define E4_DRIVER_TYPE A4988
//#define E5_DRIVER_TYPE A4988
// Enable this feature if all enabled endstop pins are interrupt-capable.
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
@ -638,14 +642,14 @@
/**
* Default Axis Steps Per Unit (steps/mm)
* Override with M92
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 2560, 95 }
/**
* Default Max Feed Rate (mm/s)
* Override with M203
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_FEEDRATE { 300, 300, 5, 25 }
@ -653,7 +657,7 @@
* Default Max Acceleration (change/s) change = mm/s
* (Maximum start speed for accelerated moves)
* Override with M201
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_ACCELERATION { 3000, 3000, 100, 10000 }
@ -892,6 +896,7 @@
#define INVERT_E2_DIR false
#define INVERT_E3_DIR false
#define INVERT_E4_DIR false
#define INVERT_E5_DIR false
// @section homing

15
Marlin/src/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h

@ -242,6 +242,7 @@
#define E2_AUTO_FAN_PIN -1
#define E3_AUTO_FAN_PIN -1
#define E4_AUTO_FAN_PIN -1
#define E5_AUTO_FAN_PIN -1
#define CHAMBER_AUTO_FAN_PIN -1
#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed
@ -482,7 +483,7 @@
//#define ADAPTIVE_STEP_SMOOTHING
// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU.
#define MICROSTEP_MODES { 16, 16, 16, 16, 16 } // [1,2,4,8,16]
#define MICROSTEP_MODES { 16, 16, 16, 16, 16, 16 } // [1,2,4,8,16]
/**
* @section stepper motor current
@ -1122,6 +1123,10 @@
#define E4_SENSE_RESISTOR 91
#define E4_MICROSTEPS 16
#define E5_MAX_CURRENT 1000
#define E5_SENSE_RESISTOR 91
#define E5_MICROSTEPS 16
#endif // TMC26X
// @section tmc_smart
@ -1186,6 +1191,9 @@
#define E4_CURRENT 800
#define E4_MICROSTEPS 16
#define E5_CURRENT 800
#define E5_MICROSTEPS 16
/**
* Use software SPI for TMC2130.
* The default SW SPI pins are defined the respective pins files,
@ -1241,6 +1249,7 @@
#define E2_HYBRID_THRESHOLD 30
#define E3_HYBRID_THRESHOLD 30
#define E4_HYBRID_THRESHOLD 30
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
@ -1358,6 +1367,10 @@
#define E4_OVERCURRENT 2000
#define E4_STALLCURRENT 1500
#define E5_MICROSTEPS 16
#define E5_OVERCURRENT 2000
#define E5_STALLCURRENT 1500
#endif // L6470
/**

11
Marlin/src/config/examples/Infitary/i3-M508/Configuration.h

@ -333,6 +333,7 @@
#define TEMP_SENSOR_2 0
#define TEMP_SENSOR_3 0
#define TEMP_SENSOR_4 0
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0
@ -363,6 +364,7 @@
#define HEATER_2_MINTEMP 5
#define HEATER_3_MINTEMP 5
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off.
@ -373,6 +375,7 @@
#define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 125
//===========================================================================
@ -597,6 +600,7 @@
//#define E2_DRIVER_TYPE A4988
//#define E3_DRIVER_TYPE A4988
//#define E4_DRIVER_TYPE A4988
//#define E5_DRIVER_TYPE A4988
// Enable this feature if all enabled endstop pins are interrupt-capable.
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
@ -642,14 +646,14 @@
/**
* Default Axis Steps Per Unit (steps/mm)
* Override with M92
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT { 100, 100, 400, 92.6 }
/**
* Default Max Feed Rate (mm/s)
* Override with M203
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_FEEDRATE { 400, 400, 5, 25 }
@ -657,7 +661,7 @@
* Default Max Acceleration (change/s) change = mm/s
* (Maximum start speed for accelerated moves)
* Override with M201
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_ACCELERATION { 9000, 9000, 100, 10000 }
@ -896,6 +900,7 @@
#define INVERT_E2_DIR false
#define INVERT_E3_DIR false
#define INVERT_E4_DIR false
#define INVERT_E5_DIR false
// @section homing

15
Marlin/src/config/examples/Infitary/i3-M508/Configuration_adv.h

@ -242,6 +242,7 @@
#define E2_AUTO_FAN_PIN -1
#define E3_AUTO_FAN_PIN -1
#define E4_AUTO_FAN_PIN -1
#define E5_AUTO_FAN_PIN -1
#define CHAMBER_AUTO_FAN_PIN -1
#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed
@ -482,7 +483,7 @@
//#define ADAPTIVE_STEP_SMOOTHING
// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU.
#define MICROSTEP_MODES { 16, 16, 16, 16, 16 } // [1,2,4,8,16]
#define MICROSTEP_MODES { 16, 16, 16, 16, 16, 16 } // [1,2,4,8,16]
/**
* @section stepper motor current
@ -1122,6 +1123,10 @@
#define E4_SENSE_RESISTOR 91
#define E4_MICROSTEPS 16
#define E5_MAX_CURRENT 1000
#define E5_SENSE_RESISTOR 91
#define E5_MICROSTEPS 16
#endif // TMC26X
// @section tmc_smart
@ -1186,6 +1191,9 @@
#define E4_CURRENT 800
#define E4_MICROSTEPS 16
#define E5_CURRENT 800
#define E5_MICROSTEPS 16
/**
* Use software SPI for TMC2130.
* The default SW SPI pins are defined the respective pins files,
@ -1241,6 +1249,7 @@
#define E2_HYBRID_THRESHOLD 30
#define E3_HYBRID_THRESHOLD 30
#define E4_HYBRID_THRESHOLD 30
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
@ -1358,6 +1367,10 @@
#define E4_OVERCURRENT 2000
#define E4_STALLCURRENT 1500
#define E5_MICROSTEPS 16
#define E5_OVERCURRENT 2000
#define E5_STALLCURRENT 1500
#endif // L6470
/**

11
Marlin/src/config/examples/JGAurora/A5/Configuration.h

@ -338,6 +338,7 @@
#define TEMP_SENSOR_2 0
#define TEMP_SENSOR_3 0
#define TEMP_SENSOR_4 0
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1 // measured to be satisfactorily accurate on center of bed within +/- 1 degC.
#define TEMP_SENSOR_CHAMBER 0
@ -368,6 +369,7 @@
#define HEATER_2_MINTEMP 5
#define HEATER_3_MINTEMP 5
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off.
@ -378,6 +380,7 @@
#define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 120
//===========================================================================
@ -605,6 +608,7 @@
//#define E2_DRIVER_TYPE A4988
//#define E3_DRIVER_TYPE A4988
//#define E4_DRIVER_TYPE A4988
//#define E5_DRIVER_TYPE A4988
// Enable this feature if all enabled endstop pins are interrupt-capable.
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
@ -650,14 +654,14 @@
/**
* Default Axis Steps Per Unit (steps/mm)
* Override with M92
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 800, 100 }
/**
* Default Max Feed Rate (mm/s)
* Override with M203
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_FEEDRATE { 500, 500, 15, 25 }
@ -665,7 +669,7 @@
* Default Max Acceleration (change/s) change = mm/s
* (Maximum start speed for accelerated moves)
* Override with M201
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_ACCELERATION { 1000, 500, 100, 5000 }
@ -904,6 +908,7 @@
#define INVERT_E2_DIR false
#define INVERT_E3_DIR false
#define INVERT_E4_DIR false
#define INVERT_E5_DIR false
// @section homing

15
Marlin/src/config/examples/JGAurora/A5/Configuration_adv.h

@ -242,6 +242,7 @@
#define E2_AUTO_FAN_PIN -1
#define E3_AUTO_FAN_PIN -1
#define E4_AUTO_FAN_PIN -1
#define E5_AUTO_FAN_PIN -1
#define CHAMBER_AUTO_FAN_PIN -1
#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed
@ -482,7 +483,7 @@
//#define ADAPTIVE_STEP_SMOOTHING
// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU.
#define MICROSTEP_MODES { 16, 16, 16, 16, 16 } // [1,2,4,8,16]
#define MICROSTEP_MODES { 16, 16, 16, 16, 16, 16 } // [1,2,4,8,16]
/**
* @section stepper motor current
@ -1122,6 +1123,10 @@
#define E4_SENSE_RESISTOR 91
#define E4_MICROSTEPS 16
#define E5_MAX_CURRENT 1000
#define E5_SENSE_RESISTOR 91
#define E5_MICROSTEPS 16
#endif // TMC26X
// @section tmc_smart
@ -1186,6 +1191,9 @@
#define E4_CURRENT 800
#define E4_MICROSTEPS 16
#define E5_CURRENT 800
#define E5_MICROSTEPS 16
/**
* Use software SPI for TMC2130.
* The default SW SPI pins are defined the respective pins files,
@ -1241,6 +1249,7 @@
#define E2_HYBRID_THRESHOLD 30
#define E3_HYBRID_THRESHOLD 30
#define E4_HYBRID_THRESHOLD 30
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
@ -1358,6 +1367,10 @@
#define E4_OVERCURRENT 2000
#define E4_STALLCURRENT 1500
#define E5_MICROSTEPS 16
#define E5_OVERCURRENT 2000
#define E5_STALLCURRENT 1500
#endif // L6470
/**

11
Marlin/src/config/examples/MakerParts/Configuration.h

@ -353,6 +353,7 @@
#define TEMP_SENSOR_2 0
#define TEMP_SENSOR_3 0
#define TEMP_SENSOR_4 0
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0
@ -383,6 +384,7 @@
#define HEATER_2_MINTEMP 5
#define HEATER_3_MINTEMP 5
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off.
@ -393,6 +395,7 @@
#define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
//===========================================================================
@ -613,6 +616,7 @@
//#define E2_DRIVER_TYPE A4988
//#define E3_DRIVER_TYPE A4988
//#define E4_DRIVER_TYPE A4988
//#define E5_DRIVER_TYPE A4988
// Enable this feature if all enabled endstop pins are interrupt-capable.
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
@ -658,14 +662,14 @@
/**
* Default Axis Steps Per Unit (steps/mm)
* Override with M92
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 4000, 97 }
/**
* Default Max Feed Rate (mm/s)
* Override with M203
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_FEEDRATE { 300, 300, 2, 30 } // For 300mm/s printing
@ -673,7 +677,7 @@
* Default Max Acceleration (change/s) change = mm/s
* (Maximum start speed for accelerated moves)
* Override with M201
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_ACCELERATION { MAX_XYAXIS_ACCEL, MAX_XYAXIS_ACCEL, 10, 200 }
@ -912,6 +916,7 @@
#define INVERT_E2_DIR false
#define INVERT_E3_DIR false
#define INVERT_E4_DIR false
#define INVERT_E5_DIR false
// @section homing

15
Marlin/src/config/examples/MakerParts/Configuration_adv.h

@ -242,6 +242,7 @@
#define E2_AUTO_FAN_PIN -1
#define E3_AUTO_FAN_PIN -1
#define E4_AUTO_FAN_PIN -1
#define E5_AUTO_FAN_PIN -1
#define CHAMBER_AUTO_FAN_PIN -1
#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed
@ -482,7 +483,7 @@
//#define ADAPTIVE_STEP_SMOOTHING
// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU.
#define MICROSTEP_MODES { 16, 16, 16, 16, 16 } // [1,2,4,8,16]
#define MICROSTEP_MODES { 16, 16, 16, 16, 16, 16 } // [1,2,4,8,16]
/**
* @section stepper motor current
@ -1122,6 +1123,10 @@
#define E4_SENSE_RESISTOR 91
#define E4_MICROSTEPS 16
#define E5_MAX_CURRENT 1000
#define E5_SENSE_RESISTOR 91
#define E5_MICROSTEPS 16
#endif // TMC26X
// @section tmc_smart
@ -1186,6 +1191,9 @@
#define E4_CURRENT 800
#define E4_MICROSTEPS 16
#define E5_CURRENT 800
#define E5_MICROSTEPS 16
/**
* Use software SPI for TMC2130.
* The default SW SPI pins are defined the respective pins files,
@ -1241,6 +1249,7 @@
#define E2_HYBRID_THRESHOLD 30
#define E3_HYBRID_THRESHOLD 30
#define E4_HYBRID_THRESHOLD 30
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
@ -1358,6 +1367,10 @@
#define E4_OVERCURRENT 2000
#define E4_STALLCURRENT 1500
#define E5_MICROSTEPS 16
#define E5_OVERCURRENT 2000
#define E5_STALLCURRENT 1500
#endif // L6470
/**

10
Marlin/src/config/examples/Malyan/M150/Configuration.h

@ -338,6 +338,7 @@
#define TEMP_SENSOR_2 0
#define TEMP_SENSOR_3 0
#define TEMP_SENSOR_4 0
#define TEMP_SENSOR_5 0
// For Malyan M150, some discussions around changing the TEMP_SENSOR_BED from 1 to 3 on a french discussion board.
// The reasons are inconclusive so I leave at 1
@ -371,6 +372,7 @@
#define HEATER_2_MINTEMP 5
#define HEATER_3_MINTEMP 5
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off.
@ -381,6 +383,7 @@
#define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
//===========================================================================
@ -624,7 +627,7 @@
/**
* Default Axis Steps Per Unit (steps/mm)
* Override with M92
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
// Standard M150 17T MXL on X and Y
#define DEFAULT_AXIS_STEPS_PER_UNIT { 3200/34.544, 3200/34.544, 1600, 103.00 }
@ -638,7 +641,7 @@
/**
* Default Max Feed Rate (mm/s)
* Override with M203
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_FEEDRATE { 300, 300, 5, 25 }
@ -646,7 +649,7 @@
* Default Max Acceleration (change/s) change = mm/s
* (Maximum start speed for accelerated moves)
* Override with M201
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_ACCELERATION { 700, 700, 100, 10000 }
@ -889,6 +892,7 @@
#define INVERT_E2_DIR false
#define INVERT_E3_DIR false
#define INVERT_E4_DIR false
#define INVERT_E5_DIR false
// @section homing

15
Marlin/src/config/examples/Malyan/M150/Configuration_adv.h

@ -242,6 +242,7 @@
#define E2_AUTO_FAN_PIN -1
#define E3_AUTO_FAN_PIN -1
#define E4_AUTO_FAN_PIN -1
#define E5_AUTO_FAN_PIN -1
#define CHAMBER_AUTO_FAN_PIN -1
#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed
@ -482,7 +483,7 @@
//#define ADAPTIVE_STEP_SMOOTHING
// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU.
#define MICROSTEP_MODES { 16, 16, 16, 16, 16 } // [1,2,4,8,16]
#define MICROSTEP_MODES { 16, 16, 16, 16, 16, 16 } // [1,2,4,8,16]
/**
* @section stepper motor current
@ -1122,6 +1123,10 @@
#define E4_SENSE_RESISTOR 91
#define E4_MICROSTEPS 16
#define E5_MAX_CURRENT 1000
#define E5_SENSE_RESISTOR 91
#define E5_MICROSTEPS 16
#endif // TMC26X
// @section tmc_smart
@ -1186,6 +1191,9 @@
#define E4_CURRENT 800
#define E4_MICROSTEPS 16
#define E5_CURRENT 800
#define E5_MICROSTEPS 16
/**
* Use software SPI for TMC2130.
* The default SW SPI pins are defined the respective pins files,
@ -1241,6 +1249,7 @@
#define E2_HYBRID_THRESHOLD 30
#define E3_HYBRID_THRESHOLD 30
#define E4_HYBRID_THRESHOLD 30
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
@ -1358,6 +1367,10 @@
#define E4_OVERCURRENT 2000
#define E4_STALLCURRENT 1500
#define E5_MICROSTEPS 16
#define E5_OVERCURRENT 2000
#define E5_STALLCURRENT 1500
#endif // L6470
/**

11
Marlin/src/config/examples/Malyan/M200/Configuration.h

@ -333,6 +333,7 @@
#define TEMP_SENSOR_2 0
#define TEMP_SENSOR_3 0
#define TEMP_SENSOR_4 0
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 11
#define TEMP_SENSOR_CHAMBER 0
@ -363,6 +364,7 @@
#define HEATER_2_MINTEMP 5
#define HEATER_3_MINTEMP 5
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off.
@ -373,6 +375,7 @@
#define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 100
//===========================================================================
@ -592,6 +595,7 @@
//#define E2_DRIVER_TYPE A4988
//#define E3_DRIVER_TYPE A4988
//#define E4_DRIVER_TYPE A4988
//#define E5_DRIVER_TYPE A4988
// Enable this feature if all enabled endstop pins are interrupt-capable.
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
@ -637,14 +641,14 @@
/**
* Default Axis Steps Per Unit (steps/mm)
* Override with M92
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT { 93, 93, 1097.5, 97 }
/**
* Default Max Feed Rate (mm/s)
* Override with M203
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_FEEDRATE { 300, 300, 5, 25 }
@ -652,7 +656,7 @@
* Default Max Acceleration (change/s) change = mm/s
* (Maximum start speed for accelerated moves)
* Override with M201
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_ACCELERATION { 3000, 3000, 100, 10000 }
@ -891,6 +895,7 @@
#define INVERT_E2_DIR false
#define INVERT_E3_DIR false
#define INVERT_E4_DIR false
#define INVERT_E5_DIR false
// @section homing

15
Marlin/src/config/examples/Malyan/M200/Configuration_adv.h

@ -242,6 +242,7 @@
#define E2_AUTO_FAN_PIN -1
#define E3_AUTO_FAN_PIN -1
#define E4_AUTO_FAN_PIN -1
#define E5_AUTO_FAN_PIN -1
#define CHAMBER_AUTO_FAN_PIN -1
#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed
@ -482,7 +483,7 @@
//#define ADAPTIVE_STEP_SMOOTHING
// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU.
#define MICROSTEP_MODES { 16, 16, 16, 16, 16 } // [1,2,4,8,16]
#define MICROSTEP_MODES { 16, 16, 16, 16, 16, 16 } // [1,2,4,8,16]
/**
* @section stepper motor current
@ -1122,6 +1123,10 @@
#define E4_SENSE_RESISTOR 91
#define E4_MICROSTEPS 16
#define E5_MAX_CURRENT 1000
#define E5_SENSE_RESISTOR 91
#define E5_MICROSTEPS 16
#endif // TMC26X
// @section tmc_smart
@ -1186,6 +1191,9 @@
#define E4_CURRENT 800
#define E4_MICROSTEPS 16
#define E5_CURRENT 800
#define E5_MICROSTEPS 16
/**
* Use software SPI for TMC2130.
* The default SW SPI pins are defined the respective pins files,
@ -1241,6 +1249,7 @@
#define E2_HYBRID_THRESHOLD 30
#define E3_HYBRID_THRESHOLD 30
#define E4_HYBRID_THRESHOLD 30
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
@ -1358,6 +1367,10 @@
#define E4_OVERCURRENT 2000
#define E4_STALLCURRENT 1500
#define E5_MICROSTEPS 16
#define E5_OVERCURRENT 2000
#define E5_STALLCURRENT 1500
#endif // L6470
/**

11
Marlin/src/config/examples/Micromake/C1/basic/Configuration.h

@ -333,6 +333,7 @@
#define TEMP_SENSOR_2 0
#define TEMP_SENSOR_3 0
#define TEMP_SENSOR_4 0
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 0
#define TEMP_SENSOR_CHAMBER 0
@ -363,6 +364,7 @@
#define HEATER_2_MINTEMP 5
#define HEATER_3_MINTEMP 5
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off.
@ -373,6 +375,7 @@
#define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
//===========================================================================
@ -593,6 +596,7 @@
//#define E2_DRIVER_TYPE A4988
//#define E3_DRIVER_TYPE A4988
//#define E4_DRIVER_TYPE A4988
//#define E5_DRIVER_TYPE A4988
// Enable this feature if all enabled endstop pins are interrupt-capable.
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
@ -638,7 +642,7 @@
/**
* Default Axis Steps Per Unit (steps/mm)
* Override with M92
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
// choose your micro step per step configuration ( 16 factory settings )
#define DEFAULT_AXIS_STEPS_PER_UNIT { 100, 100, 100, 150 } // 16 steps per unit for Micromake C1 - Factory Settings - ( MS1 : closed ; MS2 : closed on MAKEBOARD Mini)
@ -649,7 +653,7 @@
/**
* Default Max Feed Rate (mm/s)
* Override with M203
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_FEEDRATE { 200, 200, 200, 30 }
@ -657,7 +661,7 @@
* Default Max Acceleration (change/s) change = mm/s
* (Maximum start speed for accelerated moves)
* Override with M201
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_ACCELERATION { 3000, 3000, 3000, 4000 }
@ -896,6 +900,7 @@
#define INVERT_E2_DIR false
#define INVERT_E3_DIR false
#define INVERT_E4_DIR false
#define INVERT_E5_DIR false
// @section homing

11
Marlin/src/config/examples/Micromake/C1/enhanced/Configuration.h

@ -333,6 +333,7 @@
#define TEMP_SENSOR_2 0
#define TEMP_SENSOR_3 0
#define TEMP_SENSOR_4 0
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 0
#define TEMP_SENSOR_CHAMBER 0
@ -363,6 +364,7 @@
#define HEATER_2_MINTEMP 5
#define HEATER_3_MINTEMP 5
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off.
@ -373,6 +375,7 @@
#define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
//===========================================================================
@ -593,6 +596,7 @@
//#define E2_DRIVER_TYPE A4988
//#define E3_DRIVER_TYPE A4988
//#define E4_DRIVER_TYPE A4988
//#define E5_DRIVER_TYPE A4988
// Enable this feature if all enabled endstop pins are interrupt-capable.
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
@ -638,7 +642,7 @@
/**
* Default Axis Steps Per Unit (steps/mm)
* Override with M92
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
// choose your micro step per step configuration ( 16 factory settings )
//#define DEFAULT_AXIS_STEPS_PER_UNIT { 100, 100, 100, 150 } // 16 steps per unit for Micromake C1 - Factory Settings - ( MS1 : closed ; MS2 : closed on MAKEBOARD Mini)
@ -649,7 +653,7 @@
/**
* Default Max Feed Rate (mm/s)
* Override with M203
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_FEEDRATE { 200, 200, 200, 30 }
@ -657,7 +661,7 @@
* Default Max Acceleration (change/s) change = mm/s
* (Maximum start speed for accelerated moves)
* Override with M201
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_ACCELERATION { 3000, 3000, 3000, 4000 }
@ -896,6 +900,7 @@
#define INVERT_E2_DIR false
#define INVERT_E3_DIR false
#define INVERT_E4_DIR false
#define INVERT_E5_DIR false
// @section homing

15
Marlin/src/config/examples/Micromake/C1/enhanced/Configuration_adv.h

@ -242,6 +242,7 @@
#define E2_AUTO_FAN_PIN -1
#define E3_AUTO_FAN_PIN -1
#define E4_AUTO_FAN_PIN -1
#define E5_AUTO_FAN_PIN -1
#define CHAMBER_AUTO_FAN_PIN -1
#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed
@ -482,7 +483,7 @@
//#define ADAPTIVE_STEP_SMOOTHING
// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU.
#define MICROSTEP_MODES { 16, 16, 16, 16, 16 } // [1,2,4,8,16]
#define MICROSTEP_MODES { 16, 16, 16, 16, 16, 16 } // [1,2,4,8,16]
/**
* @section stepper motor current
@ -1122,6 +1123,10 @@
#define E4_SENSE_RESISTOR 91
#define E4_MICROSTEPS 16
#define E5_MAX_CURRENT 1000
#define E5_SENSE_RESISTOR 91
#define E5_MICROSTEPS 16
#endif // TMC26X
// @section tmc_smart
@ -1186,6 +1191,9 @@
#define E4_CURRENT 800
#define E4_MICROSTEPS 16
#define E5_CURRENT 800
#define E5_MICROSTEPS 16
/**
* Use software SPI for TMC2130.
* The default SW SPI pins are defined the respective pins files,
@ -1241,6 +1249,7 @@
#define E2_HYBRID_THRESHOLD 30
#define E3_HYBRID_THRESHOLD 30
#define E4_HYBRID_THRESHOLD 30
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
@ -1358,6 +1367,10 @@
#define E4_OVERCURRENT 2000
#define E4_STALLCURRENT 1500
#define E5_MICROSTEPS 16
#define E5_OVERCURRENT 2000
#define E5_STALLCURRENT 1500
#endif // L6470
/**

11
Marlin/src/config/examples/Mks/Sbase/Configuration.h

@ -333,6 +333,7 @@
#define TEMP_SENSOR_2 0
#define TEMP_SENSOR_3 0
#define TEMP_SENSOR_4 0
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 5
#define TEMP_SENSOR_CHAMBER 0
@ -363,6 +364,7 @@
#define HEATER_2_MINTEMP 5
#define HEATER_3_MINTEMP 5
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off.
@ -373,6 +375,7 @@
#define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
//===========================================================================
@ -593,6 +596,7 @@
//#define E2_DRIVER_TYPE A4988
//#define E3_DRIVER_TYPE A4988
//#define E4_DRIVER_TYPE A4988
//#define E5_DRIVER_TYPE A4988
// Enable this feature if all enabled endstop pins are interrupt-capable.
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
@ -638,14 +642,14 @@
/**
* Default Axis Steps Per Unit (steps/mm)
* Override with M92
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT { 200, 200, 800, 280 }
/**
* Default Max Feed Rate (mm/s)
* Override with M203
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_FEEDRATE { 500, 500, 5, 25 }
@ -653,7 +657,7 @@
* Default Max Acceleration (change/s) change = mm/s
* (Maximum start speed for accelerated moves)
* Override with M201
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_ACCELERATION { 9000, 9000, 100, 10000 }
@ -892,6 +896,7 @@
#define INVERT_E2_DIR false
#define INVERT_E3_DIR false
#define INVERT_E4_DIR false
#define INVERT_E5_DIR false
// @section homing

15
Marlin/src/config/examples/Mks/Sbase/Configuration_adv.h

@ -242,6 +242,7 @@
#define E2_AUTO_FAN_PIN -1
#define E3_AUTO_FAN_PIN -1
#define E4_AUTO_FAN_PIN -1
#define E5_AUTO_FAN_PIN -1
#define CHAMBER_AUTO_FAN_PIN -1
#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed
@ -482,7 +483,7 @@
//#define ADAPTIVE_STEP_SMOOTHING
// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU.
#define MICROSTEP_MODES { 16, 16, 16, 16, 16 } // [1,2,4,8,16]
#define MICROSTEP_MODES { 16, 16, 16, 16, 16, 16 } // [1,2,4,8,16]
/**
* @section stepper motor current
@ -1130,6 +1131,10 @@
#define E4_SENSE_RESISTOR 91
#define E4_MICROSTEPS 16
#define E5_MAX_CURRENT 1000
#define E5_SENSE_RESISTOR 91
#define E5_MICROSTEPS 16
#endif // TMC26X
// @section tmc_smart
@ -1194,6 +1199,9 @@
#define E4_CURRENT 800
#define E4_MICROSTEPS 16
#define E5_CURRENT 800
#define E5_MICROSTEPS 16
/**
* Use software SPI for TMC2130.
* The default SW SPI pins are defined the respective pins files,
@ -1249,6 +1257,7 @@
#define E2_HYBRID_THRESHOLD 30
#define E3_HYBRID_THRESHOLD 30
#define E4_HYBRID_THRESHOLD 30
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
@ -1366,6 +1375,10 @@
#define E4_OVERCURRENT 2000
#define E4_STALLCURRENT 1500
#define E5_MICROSTEPS 16
#define E5_OVERCURRENT 2000
#define E5_STALLCURRENT 1500
#endif // L6470
/**

11
Marlin/src/config/examples/RepRapPro/Huxley/Configuration.h

@ -333,6 +333,7 @@
#define TEMP_SENSOR_2 0
#define TEMP_SENSOR_3 0
#define TEMP_SENSOR_4 0
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1 // Sanguinololu v1.3 with 4.7kOhm pullup
#define TEMP_SENSOR_CHAMBER 0
@ -363,6 +364,7 @@
#define HEATER_2_MINTEMP 5
#define HEATER_3_MINTEMP 5
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off.
@ -373,6 +375,7 @@
#define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
//===========================================================================
@ -593,6 +596,7 @@
//#define E2_DRIVER_TYPE A4988
//#define E3_DRIVER_TYPE A4988
//#define E4_DRIVER_TYPE A4988
//#define E5_DRIVER_TYPE A4988
// Enable this feature if all enabled endstop pins are interrupt-capable.
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
@ -677,14 +681,14 @@ Black rubber belt(MXL), 18 - tooth aluminium pulley : 87.489 step per mm (Huxley
/**
* Default Axis Steps Per Unit (steps/mm)
* Override with M92
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT { XY_STEPS, XY_STEPS, Z_STEPS, E_STEPS }
/**
* Default Max Feed Rate (mm/s)
* Override with M203
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_Z_FEEDRATE 3.3 // older Huxley has problem with speeds > 3.3 mm/s on z axis
#define DEFAULT_MAX_FEEDRATE { 200, 200, DEFAULT_MAX_Z_FEEDRATE, 25 }
@ -693,7 +697,7 @@ Black rubber belt(MXL), 18 - tooth aluminium pulley : 87.489 step per mm (Huxley
* Default Max Acceleration (change/s) change = mm/s
* (Maximum start speed for accelerated moves)
* Override with M201
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_ACCELERATION { 1000, 1000, 50, 1000 }
@ -932,6 +936,7 @@ Black rubber belt(MXL), 18 - tooth aluminium pulley : 87.489 step per mm (Huxley
#define INVERT_E2_DIR false
#define INVERT_E3_DIR false
#define INVERT_E4_DIR false
#define INVERT_E5_DIR false
// @section homing

11
Marlin/src/config/examples/RepRapWorld/Megatronics/Configuration.h

@ -333,6 +333,7 @@
#define TEMP_SENSOR_2 0
#define TEMP_SENSOR_3 0
#define TEMP_SENSOR_4 0
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0
@ -363,6 +364,7 @@
#define HEATER_2_MINTEMP 5
#define HEATER_3_MINTEMP 5
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off.
@ -373,6 +375,7 @@
#define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
//===========================================================================
@ -593,6 +596,7 @@
//#define E2_DRIVER_TYPE A4988
//#define E3_DRIVER_TYPE A4988
//#define E4_DRIVER_TYPE A4988
//#define E5_DRIVER_TYPE A4988
// Enable this feature if all enabled endstop pins are interrupt-capable.
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
@ -638,14 +642,14 @@
/**
* Default Axis Steps Per Unit (steps/mm)
* Override with M92
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT { 78.7402*2, 78.7402*2, 5120.00, 760*1*1.5 }
/**
* Default Max Feed Rate (mm/s)
* Override with M203
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_FEEDRATE { 300, 300, 5, 25 }
@ -653,7 +657,7 @@
* Default Max Acceleration (change/s) change = mm/s
* (Maximum start speed for accelerated moves)
* Override with M201
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_ACCELERATION { 3000, 3000, 100, 10000 }
@ -892,6 +896,7 @@
#define INVERT_E2_DIR false
#define INVERT_E3_DIR false
#define INVERT_E4_DIR false
#define INVERT_E5_DIR false
// @section homing

11
Marlin/src/config/examples/RigidBot/Configuration.h

@ -336,6 +336,7 @@
#define TEMP_SENSOR_2 0
#define TEMP_SENSOR_3 0
#define TEMP_SENSOR_4 0
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0
@ -366,6 +367,7 @@
#define HEATER_2_MINTEMP 5
#define HEATER_3_MINTEMP 5
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off.
@ -376,6 +378,7 @@
#define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
//===========================================================================
@ -589,6 +592,7 @@
//#define E2_DRIVER_TYPE A4988
//#define E3_DRIVER_TYPE A4988
//#define E4_DRIVER_TYPE A4988
//#define E5_DRIVER_TYPE A4988
// Enable this feature if all enabled endstop pins are interrupt-capable.
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
@ -634,7 +638,7 @@
/**
* Default Axis Steps Per Unit (steps/mm)
* Override with M92
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
// default steps per unit for RigidBot with standard hardware
#define DEFAULT_AXIS_STEPS_PER_UNIT { 44.3090, 22.1545, 1600, 53.5 }
@ -643,7 +647,7 @@
/**
* Default Max Feed Rate (mm/s)
* Override with M203
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_FEEDRATE { 500, 500, 5, 25 }
@ -651,7 +655,7 @@
* Default Max Acceleration (change/s) change = mm/s
* (Maximum start speed for accelerated moves)
* Override with M201
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_ACCELERATION { 800, 800, 100, 10000 }
@ -890,6 +894,7 @@
#define INVERT_E2_DIR false
#define INVERT_E3_DIR false
#define INVERT_E4_DIR false
#define INVERT_E5_DIR false
// @section homing

15
Marlin/src/config/examples/RigidBot/Configuration_adv.h

@ -242,6 +242,7 @@
#define E2_AUTO_FAN_PIN -1
#define E3_AUTO_FAN_PIN -1
#define E4_AUTO_FAN_PIN -1
#define E5_AUTO_FAN_PIN -1
#define CHAMBER_AUTO_FAN_PIN -1
#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed
@ -482,7 +483,7 @@
//#define ADAPTIVE_STEP_SMOOTHING
// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU.
#define MICROSTEP_MODES { 16, 16, 16, 16, 16 } // [1,2,4,8,16]
#define MICROSTEP_MODES { 16, 16, 16, 16, 16, 16 } // [1,2,4,8,16]
/**
* @section stepper motor current
@ -1122,6 +1123,10 @@
#define E4_SENSE_RESISTOR 91
#define E4_MICROSTEPS 16
#define E5_MAX_CURRENT 1000
#define E5_SENSE_RESISTOR 91
#define E5_MICROSTEPS 16
#endif // TMC26X
// @section tmc_smart
@ -1186,6 +1191,9 @@
#define E4_CURRENT 800
#define E4_MICROSTEPS 16
#define E5_CURRENT 800
#define E5_MICROSTEPS 16
/**
* Use software SPI for TMC2130.
* The default SW SPI pins are defined the respective pins files,
@ -1241,6 +1249,7 @@
#define E2_HYBRID_THRESHOLD 30
#define E3_HYBRID_THRESHOLD 30
#define E4_HYBRID_THRESHOLD 30
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
@ -1358,6 +1367,10 @@
#define E4_OVERCURRENT 2000
#define E4_STALLCURRENT 1500
#define E5_MICROSTEPS 16
#define E5_OVERCURRENT 2000
#define E5_STALLCURRENT 1500
#endif // L6470
/**

11
Marlin/src/config/examples/SCARA/Configuration.h

@ -364,6 +364,7 @@
#define TEMP_SENSOR_2 0
#define TEMP_SENSOR_3 0
#define TEMP_SENSOR_4 0
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0
@ -394,6 +395,7 @@
#define HEATER_2_MINTEMP 5
#define HEATER_3_MINTEMP 5
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off.
@ -404,6 +406,7 @@
#define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
//===========================================================================
@ -606,6 +609,7 @@
//#define E2_DRIVER_TYPE A4988
//#define E3_DRIVER_TYPE A4988
//#define E4_DRIVER_TYPE A4988
//#define E5_DRIVER_TYPE A4988
// Enable this feature if all enabled endstop pins are interrupt-capable.
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
@ -651,14 +655,14 @@
/**
* Default Axis Steps Per Unit (steps/mm)
* Override with M92
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT { 103.69, 106.65, 200/1.25, 1000 } // default steps per unit for SCARA
/**
* Default Max Feed Rate (mm/s)
* Override with M203
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_FEEDRATE { 300, 300, 30, 25 }
@ -666,7 +670,7 @@
* Default Max Acceleration (change/s) change = mm/s
* (Maximum start speed for accelerated moves)
* Override with M201
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_ACCELERATION { 300, 300, 20, 1000 }
@ -905,6 +909,7 @@
#define INVERT_E2_DIR false
#define INVERT_E3_DIR false
#define INVERT_E4_DIR false
#define INVERT_E5_DIR false
// @section homing

15
Marlin/src/config/examples/SCARA/Configuration_adv.h

@ -242,6 +242,7 @@
#define E2_AUTO_FAN_PIN -1
#define E3_AUTO_FAN_PIN -1
#define E4_AUTO_FAN_PIN -1
#define E5_AUTO_FAN_PIN -1
#define CHAMBER_AUTO_FAN_PIN -1
#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed
@ -482,7 +483,7 @@
//#define ADAPTIVE_STEP_SMOOTHING
// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU.
#define MICROSTEP_MODES { 16, 16, 16, 16, 16 } // [1,2,4,8,16]
#define MICROSTEP_MODES { 16, 16, 16, 16, 16, 16 } // [1,2,4,8,16]
/**
* @section stepper motor current
@ -1122,6 +1123,10 @@
#define E4_SENSE_RESISTOR 91
#define E4_MICROSTEPS 16
#define E5_MAX_CURRENT 1000
#define E5_SENSE_RESISTOR 91
#define E5_MICROSTEPS 16
#endif // TMC26X
// @section tmc_smart
@ -1186,6 +1191,9 @@
#define E4_CURRENT 800
#define E4_MICROSTEPS 16
#define E5_CURRENT 800
#define E5_MICROSTEPS 16
/**
* Use software SPI for TMC2130.
* The default SW SPI pins are defined the respective pins files,
@ -1241,6 +1249,7 @@
#define E2_HYBRID_THRESHOLD 30
#define E3_HYBRID_THRESHOLD 30
#define E4_HYBRID_THRESHOLD 30
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
@ -1358,6 +1367,10 @@
#define E4_OVERCURRENT 2000
#define E4_STALLCURRENT 1500
#define E5_MICROSTEPS 16
#define E5_OVERCURRENT 2000
#define E5_STALLCURRENT 1500
#endif // L6470
/**

11
Marlin/src/config/examples/STM32F10/Configuration.h

@ -334,6 +334,7 @@
#define TEMP_SENSOR_2 0
#define TEMP_SENSOR_3 0
#define TEMP_SENSOR_4 0
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 998
#define TEMP_SENSOR_CHAMBER 0
@ -364,6 +365,7 @@
#define HEATER_2_MINTEMP 5
#define HEATER_3_MINTEMP 5
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off.
@ -374,6 +376,7 @@
#define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
//===========================================================================
@ -595,6 +598,7 @@
//#define E2_DRIVER_TYPE A4988
//#define E3_DRIVER_TYPE A4988
//#define E4_DRIVER_TYPE A4988
//#define E5_DRIVER_TYPE A4988
// Enable this feature if all enabled endstop pins are interrupt-capable.
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
@ -640,14 +644,14 @@
/**
* Default Axis Steps Per Unit (steps/mm)
* Override with M92
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT { 78.74, 78.74, 2560, 105.0 }
/**
* Default Max Feed Rate (mm/s)
* Override with M203
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_FEEDRATE { 400, 400, 2, 45 }
@ -655,7 +659,7 @@
* Default Max Acceleration (change/s) change = mm/s
* (Maximum start speed for accelerated moves)
* Override with M201
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_ACCELERATION { 1400, 1400, 100, 80000 }
@ -894,6 +898,7 @@
#define INVERT_E2_DIR false
#define INVERT_E3_DIR false
#define INVERT_E4_DIR false
#define INVERT_E5_DIR false
// @section homing

11
Marlin/src/config/examples/STM32F4/Configuration.h

@ -333,6 +333,7 @@
#define TEMP_SENSOR_2 0
#define TEMP_SENSOR_3 0
#define TEMP_SENSOR_4 0
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 0
#define TEMP_SENSOR_CHAMBER 0
@ -363,6 +364,7 @@
#define HEATER_2_MINTEMP 5
#define HEATER_3_MINTEMP 5
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off.
@ -373,6 +375,7 @@
#define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
//===========================================================================
@ -593,6 +596,7 @@
//#define E2_DRIVER_TYPE A4988
//#define E3_DRIVER_TYPE A4988
//#define E4_DRIVER_TYPE A4988
//#define E5_DRIVER_TYPE A4988
// Enable this feature if all enabled endstop pins are interrupt-capable.
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
@ -638,14 +642,14 @@
/**
* Default Axis Steps Per Unit (steps/mm)
* Override with M92
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 4000, 500 }
/**
* Default Max Feed Rate (mm/s)
* Override with M203
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_FEEDRATE { 300, 300, 5, 25 }
@ -653,7 +657,7 @@
* Default Max Acceleration (change/s) change = mm/s
* (Maximum start speed for accelerated moves)
* Override with M201
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_ACCELERATION { 3000, 3000, 100, 10000 }
@ -892,6 +896,7 @@
#define INVERT_E2_DIR false
#define INVERT_E3_DIR false
#define INVERT_E4_DIR false
#define INVERT_E5_DIR false
// @section homing

11
Marlin/src/config/examples/Sanguinololu/Configuration.h

@ -333,6 +333,7 @@
#define TEMP_SENSOR_2 0
#define TEMP_SENSOR_3 0
#define TEMP_SENSOR_4 0
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0
@ -363,6 +364,7 @@
#define HEATER_2_MINTEMP 5
#define HEATER_3_MINTEMP 5
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off.
@ -373,6 +375,7 @@
#define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
//===========================================================================
@ -593,6 +596,7 @@
//#define E2_DRIVER_TYPE A4988
//#define E3_DRIVER_TYPE A4988
//#define E4_DRIVER_TYPE A4988
//#define E5_DRIVER_TYPE A4988
// Enable this feature if all enabled endstop pins are interrupt-capable.
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
@ -669,14 +673,14 @@
/**
* Default Axis Steps Per Unit (steps/mm)
* Override with M92
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT { XY_STEPS, XY_STEPS, Z_STEPS, E_STEPS }
/**
* Default Max Feed Rate (mm/s)
* Override with M203
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_FEEDRATE { 500, 500, 8, 45 }
@ -684,7 +688,7 @@
* Default Max Acceleration (change/s) change = mm/s
* (Maximum start speed for accelerated moves)
* Override with M201
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_ACCELERATION { 3000, 3000, 100, 10000 }
@ -923,6 +927,7 @@
#define INVERT_E2_DIR false
#define INVERT_E3_DIR false
#define INVERT_E4_DIR false
#define INVERT_E5_DIR false
// @section homing

15
Marlin/src/config/examples/Sanguinololu/Configuration_adv.h

@ -242,6 +242,7 @@
#define E2_AUTO_FAN_PIN -1
#define E3_AUTO_FAN_PIN -1
#define E4_AUTO_FAN_PIN -1
#define E5_AUTO_FAN_PIN -1
#define CHAMBER_AUTO_FAN_PIN -1
#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed
@ -482,7 +483,7 @@
//#define ADAPTIVE_STEP_SMOOTHING
// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU.
#define MICROSTEP_MODES { 16, 16, 16, 16, 16 } // [1,2,4,8,16]
#define MICROSTEP_MODES { 16, 16, 16, 16, 16, 16 } // [1,2,4,8,16]
/**
* @section stepper motor current
@ -1122,6 +1123,10 @@
#define E4_SENSE_RESISTOR 91
#define E4_MICROSTEPS 16
#define E5_MAX_CURRENT 1000
#define E5_SENSE_RESISTOR 91
#define E5_MICROSTEPS 16
#endif // TMC26X
// @section tmc_smart
@ -1186,6 +1191,9 @@
#define E4_CURRENT 800
#define E4_MICROSTEPS 16
#define E5_CURRENT 800
#define E5_MICROSTEPS 16
/**
* Use software SPI for TMC2130.
* The default SW SPI pins are defined the respective pins files,
@ -1241,6 +1249,7 @@
#define E2_HYBRID_THRESHOLD 30
#define E3_HYBRID_THRESHOLD 30
#define E4_HYBRID_THRESHOLD 30
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
@ -1358,6 +1367,10 @@
#define E4_OVERCURRENT 2000
#define E4_STALLCURRENT 1500
#define E5_MICROSTEPS 16
#define E5_OVERCURRENT 2000
#define E5_STALLCURRENT 1500
#endif // L6470
/**

11
Marlin/src/config/examples/TheBorg/Configuration.h

@ -333,6 +333,7 @@
#define TEMP_SENSOR_2 0
#define TEMP_SENSOR_3 0
#define TEMP_SENSOR_4 0
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 5
#define TEMP_SENSOR_CHAMBER 0
@ -363,6 +364,7 @@
#define HEATER_2_MINTEMP 5
#define HEATER_3_MINTEMP 5
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off.
@ -373,6 +375,7 @@
#define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
//===========================================================================
@ -593,6 +596,7 @@
//#define E2_DRIVER_TYPE A4988
//#define E3_DRIVER_TYPE A4988
//#define E4_DRIVER_TYPE A4988
//#define E5_DRIVER_TYPE A4988
// Enable this feature if all enabled endstop pins are interrupt-capable.
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
@ -638,14 +642,14 @@
/**
* Default Axis Steps Per Unit (steps/mm)
* Override with M92
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT { 200, 200, 800, 280 }
/**
* Default Max Feed Rate (mm/s)
* Override with M203
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_FEEDRATE { 500, 500, 5, 25 }
@ -653,7 +657,7 @@
* Default Max Acceleration (change/s) change = mm/s
* (Maximum start speed for accelerated moves)
* Override with M201
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_ACCELERATION { 9000, 9000, 100, 10000 }
@ -892,6 +896,7 @@
#define INVERT_E2_DIR false
#define INVERT_E3_DIR false
#define INVERT_E4_DIR false
#define INVERT_E5_DIR false
// @section homing

15
Marlin/src/config/examples/TheBorg/Configuration_adv.h

@ -242,6 +242,7 @@
#define E2_AUTO_FAN_PIN -1
#define E3_AUTO_FAN_PIN -1
#define E4_AUTO_FAN_PIN -1
#define E5_AUTO_FAN_PIN -1
#define CHAMBER_AUTO_FAN_PIN -1
#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed
@ -482,7 +483,7 @@
//#define ADAPTIVE_STEP_SMOOTHING
// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU.
#define MICROSTEP_MODES { 16, 16, 16, 16, 16 } // [1,2,4,8,16]
#define MICROSTEP_MODES { 16, 16, 16, 16, 16, 16 } // [1,2,4,8,16]
/**
* @section stepper motor current
@ -1122,6 +1123,10 @@
#define E4_SENSE_RESISTOR 91
#define E4_MICROSTEPS 16
#define E5_MAX_CURRENT 1000
#define E5_SENSE_RESISTOR 91
#define E5_MICROSTEPS 16
#endif // TMC26X
// @section tmc_smart
@ -1186,6 +1191,9 @@
#define E4_CURRENT 800
#define E4_MICROSTEPS 16
#define E5_CURRENT 800
#define E5_MICROSTEPS 16
/**
* Use software SPI for TMC2130.
* The default SW SPI pins are defined the respective pins files,
@ -1241,6 +1249,7 @@
#define E2_HYBRID_THRESHOLD 30
#define E3_HYBRID_THRESHOLD 30
#define E4_HYBRID_THRESHOLD 30
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
@ -1358,6 +1367,10 @@
#define E4_OVERCURRENT 2000
#define E4_STALLCURRENT 1500
#define E5_MICROSTEPS 16
#define E5_OVERCURRENT 2000
#define E5_STALLCURRENT 1500
#endif // L6470
/**

11
Marlin/src/config/examples/TinyBoy2/Configuration.h

@ -355,6 +355,7 @@
#define TEMP_SENSOR_2 0
#define TEMP_SENSOR_3 0
#define TEMP_SENSOR_4 0
#define TEMP_SENSOR_5 0
#if ENABLED(TB2_HEATBED_MOD)
// K8200 Heatbed 1206/100k/3950K spare part
#define TEMP_SENSOR_BED 7
@ -390,6 +391,7 @@
#define HEATER_2_MINTEMP 5
#define HEATER_3_MINTEMP 5
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off.
@ -400,6 +402,7 @@
#define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 100
//===========================================================================
@ -644,6 +647,7 @@
//#define E2_DRIVER_TYPE A4988
//#define E3_DRIVER_TYPE A4988
//#define E4_DRIVER_TYPE A4988
//#define E5_DRIVER_TYPE A4988
// Enable this feature if all enabled endstop pins are interrupt-capable.
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
@ -689,14 +693,14 @@
/**
* Default Axis Steps Per Unit (steps/mm)
* Override with M92
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT { 100, 100, 6400, 88.16 }
/**
* Default Max Feed Rate (mm/s)
* Override with M203
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_FEEDRATE { 300, 300, 7, 35 }
@ -704,7 +708,7 @@
* Default Max Acceleration (change/s) change = mm/s
* (Maximum start speed for accelerated moves)
* Override with M201
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_ACCELERATION { 3000, 3000, 100, 10000 }
@ -943,6 +947,7 @@
#define INVERT_E2_DIR false
#define INVERT_E3_DIR false
#define INVERT_E4_DIR false
#define INVERT_E5_DIR false
// @section homing

15
Marlin/src/config/examples/TinyBoy2/Configuration_adv.h

@ -242,6 +242,7 @@
#define E2_AUTO_FAN_PIN -1
#define E3_AUTO_FAN_PIN -1
#define E4_AUTO_FAN_PIN -1
#define E5_AUTO_FAN_PIN -1
#define CHAMBER_AUTO_FAN_PIN -1
#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed
@ -482,7 +483,7 @@
//#define ADAPTIVE_STEP_SMOOTHING
// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU.
#define MICROSTEP_MODES { 16, 16, 16, 16, 16 } // [1,2,4,8,16]
#define MICROSTEP_MODES { 16, 16, 16, 16, 16, 16 } // [1,2,4,8,16]
/**
* @section stepper motor current
@ -1122,6 +1123,10 @@
#define E4_SENSE_RESISTOR 91
#define E4_MICROSTEPS 16
#define E5_MAX_CURRENT 1000
#define E5_SENSE_RESISTOR 91
#define E5_MICROSTEPS 16
#endif // TMC26X
// @section tmc_smart
@ -1186,6 +1191,9 @@
#define E4_CURRENT 800
#define E4_MICROSTEPS 16
#define E5_CURRENT 800
#define E5_MICROSTEPS 16
/**
* Use software SPI for TMC2130.
* The default SW SPI pins are defined the respective pins files,
@ -1241,6 +1249,7 @@
#define E2_HYBRID_THRESHOLD 30
#define E3_HYBRID_THRESHOLD 30
#define E4_HYBRID_THRESHOLD 30
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
@ -1358,6 +1367,10 @@
#define E4_OVERCURRENT 2000
#define E4_STALLCURRENT 1500
#define E5_MICROSTEPS 16
#define E5_OVERCURRENT 2000
#define E5_STALLCURRENT 1500
#endif // L6470
/**

11
Marlin/src/config/examples/Tronxy/X1/Configuration.h

@ -333,6 +333,7 @@
#define TEMP_SENSOR_2 0
#define TEMP_SENSOR_3 0
#define TEMP_SENSOR_4 0
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 0
#define TEMP_SENSOR_CHAMBER 0
@ -363,6 +364,7 @@
#define HEATER_2_MINTEMP 5
#define HEATER_3_MINTEMP 5
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off.
@ -373,6 +375,7 @@
#define HEATER_2_MAXTEMP 260
#define HEATER_3_MAXTEMP 260
#define HEATER_4_MAXTEMP 260
#define HEATER_5_MAXTEMP 260
#define BED_MAXTEMP 150
//===========================================================================
@ -593,6 +596,7 @@
//#define E2_DRIVER_TYPE A4988
//#define E3_DRIVER_TYPE A4988
//#define E4_DRIVER_TYPE A4988
//#define E5_DRIVER_TYPE A4988
// Enable this feature if all enabled endstop pins are interrupt-capable.
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
@ -638,14 +642,14 @@
/**
* Default Axis Steps Per Unit (steps/mm)
* Override with M92
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT { 100, 100, 1600, 90 }
/**
* Default Max Feed Rate (mm/s)
* Override with M203
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_FEEDRATE { 400, 400, 2, 50 }
@ -653,7 +657,7 @@
* Default Max Acceleration (change/s) change = mm/s
* (Maximum start speed for accelerated moves)
* Override with M201
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_ACCELERATION { 400, 400, 40, 5000 }
@ -892,6 +896,7 @@
#define INVERT_E2_DIR false
#define INVERT_E3_DIR false
#define INVERT_E4_DIR false
#define INVERT_E5_DIR false
// @section homing

11
Marlin/src/config/examples/Tronxy/X3A/Configuration.h

@ -333,6 +333,7 @@
#define TEMP_SENSOR_2 0
#define TEMP_SENSOR_3 0
#define TEMP_SENSOR_4 0
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 501
#define TEMP_SENSOR_CHAMBER 0
@ -363,6 +364,7 @@
#define HEATER_2_MINTEMP 5
#define HEATER_3_MINTEMP 5
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off.
@ -373,6 +375,7 @@
#define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 130
//===========================================================================
@ -593,6 +596,7 @@
//#define E2_DRIVER_TYPE A4988
//#define E3_DRIVER_TYPE A4988
//#define E4_DRIVER_TYPE A4988
//#define E5_DRIVER_TYPE A4988
// Enable this feature if all enabled endstop pins are interrupt-capable.
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
@ -638,14 +642,14 @@
/**
* Default Axis Steps Per Unit (steps/mm)
* Override with M92
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT { 100, 100, 400, 90 }
/**
* Default Max Feed Rate (mm/s)
* Override with M203
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_FEEDRATE { 400, 400, 4, 50 }
@ -653,7 +657,7 @@
* Default Max Acceleration (change/s) change = mm/s
* (Maximum start speed for accelerated moves)
* Override with M201
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_ACCELERATION { 1000, 1000, 1500, 5000 }
@ -892,6 +896,7 @@
#define INVERT_E2_DIR false
#define INVERT_E3_DIR false
#define INVERT_E4_DIR false
#define INVERT_E5_DIR false
// @section homing

15
Marlin/src/config/examples/Tronxy/X3A/Configuration_adv.h

@ -242,6 +242,7 @@
#define E2_AUTO_FAN_PIN -1
#define E3_AUTO_FAN_PIN -1
#define E4_AUTO_FAN_PIN -1
#define E5_AUTO_FAN_PIN -1
#define CHAMBER_AUTO_FAN_PIN -1
#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed
@ -471,7 +472,7 @@
//#define ADAPTIVE_STEP_SMOOTHING
// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU.
#define MICROSTEP_MODES { 16, 16, 16, 16, 16 } // [1,2,4,8,16]
#define MICROSTEP_MODES { 16, 16, 16, 16, 16, 16 } // [1,2,4,8,16]
/**
* @section stepper motor current
@ -1111,6 +1112,10 @@
#define E4_SENSE_RESISTOR 91
#define E4_MICROSTEPS 16
#define E5_MAX_CURRENT 1000
#define E5_SENSE_RESISTOR 91
#define E5_MICROSTEPS 16
#endif // TMC26X
// @section tmc_smart
@ -1175,6 +1180,9 @@
#define E4_CURRENT 800
#define E4_MICROSTEPS 16
#define E5_CURRENT 800
#define E5_MICROSTEPS 16
/**
* Use software SPI for TMC2130.
* The default SW SPI pins are defined the respective pins files,
@ -1230,6 +1238,7 @@
#define E2_HYBRID_THRESHOLD 30
#define E3_HYBRID_THRESHOLD 30
#define E4_HYBRID_THRESHOLD 30
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
@ -1347,6 +1356,10 @@
#define E4_OVERCURRENT 2000
#define E4_STALLCURRENT 1500
#define E5_MICROSTEPS 16
#define E5_OVERCURRENT 2000
#define E5_STALLCURRENT 1500
#endif // L6470
/**

11
Marlin/src/config/examples/Tronxy/X5S/Configuration.h

@ -333,6 +333,7 @@
#define TEMP_SENSOR_2 0
#define TEMP_SENSOR_3 0
#define TEMP_SENSOR_4 0
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0
@ -363,6 +364,7 @@
#define HEATER_2_MINTEMP 5
#define HEATER_3_MINTEMP 5
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off.
@ -373,6 +375,7 @@
#define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
//===========================================================================
@ -593,6 +596,7 @@
//#define E2_DRIVER_TYPE A4988
//#define E3_DRIVER_TYPE A4988
//#define E4_DRIVER_TYPE A4988
//#define E5_DRIVER_TYPE A4988
// Enable this feature if all enabled endstop pins are interrupt-capable.
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
@ -638,14 +642,14 @@
/**
* Default Axis Steps Per Unit (steps/mm)
* Override with M92
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 400, 90 }
/**
* Default Max Feed Rate (mm/s)
* Override with M203
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_FEEDRATE { 400, 400, 4, 150 }
@ -653,7 +657,7 @@
* Default Max Acceleration (change/s) change = mm/s
* (Maximum start speed for accelerated moves)
* Override with M201
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_ACCELERATION { 1000, 1000, 1000, 1000 }
@ -892,6 +896,7 @@
#define INVERT_E2_DIR false
#define INVERT_E3_DIR false
#define INVERT_E4_DIR false
#define INVERT_E5_DIR false
// @section homing

11
Marlin/src/config/examples/Tronxy/XY100/Configuration.h

@ -333,6 +333,7 @@
#define TEMP_SENSOR_2 0
#define TEMP_SENSOR_3 0
#define TEMP_SENSOR_4 0
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 0
#define TEMP_SENSOR_CHAMBER 0
@ -363,6 +364,7 @@
#define HEATER_2_MINTEMP 5
#define HEATER_3_MINTEMP 5
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off.
@ -373,6 +375,7 @@
#define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
//===========================================================================
@ -604,6 +607,7 @@
//#define E2_DRIVER_TYPE A4988
//#define E3_DRIVER_TYPE A4988
//#define E4_DRIVER_TYPE A4988
//#define E5_DRIVER_TYPE A4988
// Enable this feature if all enabled endstop pins are interrupt-capable.
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
@ -649,14 +653,14 @@
/**
* Default Axis Steps Per Unit (steps/mm)
* Override with M92
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT { 100, 100, 1600, 90 }
/**
* Default Max Feed Rate (mm/s)
* Override with M203
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_FEEDRATE { 400, 400, 4, 50 }
@ -664,7 +668,7 @@
* Default Max Acceleration (change/s) change = mm/s
* (Maximum start speed for accelerated moves)
* Override with M201
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/
#define DEFAULT_MAX_ACCELERATION { 3000, 3000, 1000, 5000 }
@ -903,6 +907,7 @@
#define INVERT_E2_DIR false
#define INVERT_E3_DIR false
#define INVERT_E4_DIR false
#define INVERT_E5_DIR false
// @section homing

Some files were not shown because too many files changed in this diff

Loading…
Cancel
Save