🎨 Misc. code cleanup

Marlin/src/MarlinCore.cpp

@@ -1554,6 +1554,7 @@ void setup() {
   #endif
 
   #if HAS_DWIN_E3V2_BASIC
+    SETUP_LOG("E3V2 Init");
     Encoder_Configuration();
     HMI_Init();
     HMI_SetLanguageCache();
@@ -1562,7 +1563,7 @@ void setup() {
   #endif
 
   #if HAS_SERVICE_INTERVALS && !HAS_DWIN_E3V2_BASIC
-    ui.reset_status(true);  // Show service messages or keep current status
+    SETUP_RUN(ui.reset_status(true));  // Show service messages or keep current status
   #endif
 
   #if ENABLED(MAX7219_DEBUG)
@@ -1593,7 +1594,7 @@ void setup() {
   #endif
 
   #if BOTH(HAS_LCD_MENU, TOUCH_SCREEN_CALIBRATION) && EITHER(TFT_CLASSIC_UI, TFT_COLOR_UI)
-    ui.check_touch_calibration();
+    SETUP_RUN(ui.check_touch_calibration());
   #endif
 
   marlin_state = MF_RUNNING;

Marlin/src/feature/twibus.cpp

@@ -98,7 +98,7 @@ void TWIBus::echodata(uint8_t bytes, FSTR_P const pref, uint8_t adr, const uint8
   union TwoBytesToInt16 { uint8_t bytes[2]; int16_t integervalue; };
   TwoBytesToInt16 ConversionUnion;
 
-  echoprefix(bytes, pref, adr);  
+  echoprefix(bytes, pref, adr);
 
   while (bytes-- && Wire.available()) {
     int value = Wire.read();

Marlin/src/pins/stm32f1/pins_ERYONE_ERY32_MINI.h

@@ -54,7 +54,7 @@
 
 //
 // Limit Switches
-// 
+//
 #define X_STOP_PIN                          PD8
 #define Y_STOP_PIN                          PD15
 #define Z_MIN_PIN                           PA11
@@ -173,7 +173,7 @@
   #define LCD_PINS_D5                       PE7
   #define LCD_PINS_D6                       PB2
   #define LCD_PINS_D7                       PB1
-  
+
   #if ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER)
     #define BTN_ENC_EN               LCD_PINS_D7  // Detect the presence of the encoder
   #endif

buildroot/share/PlatformIO/variants/MARLIN_BIGTREE_OCTOPUS_PRO_V1_F429/variant.cpp

@@ -190,12 +190,12 @@ WEAK void SystemClock_Config(void)
 
   /* Enable Power Control clock */
   __HAL_RCC_PWR_CLK_ENABLE();
-  
+
-  /* The voltage scaling allows optimizing the power consumption when the device is 
+  /* The voltage scaling allows optimizing the power consumption when the device is
-     clocked below the maximum system frequency, to update the voltage scaling value 
+     clocked below the maximum system frequency, to update the voltage scaling value
      regarding system frequency refer to product datasheet.  */
   __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
-  
+
   /* Enable HSE Oscillator and activate PLL with HSE as source */
   RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
   RCC_OscInitStruct.HSEState = RCC_HSE_ON;
@@ -209,19 +209,19 @@ WEAK void SystemClock_Config(void)
   {
     /* Initialization Error */
   }
-  
+
   if(HAL_PWREx_EnableOverDrive() != HAL_OK)
   {
     /* Initialization Error */
   }
-  
+
-  /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 
+  /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2
      clocks dividers */
   RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
   RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
   RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
-  RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4;  
+  RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4;
-  RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2;  
+  RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2;
   if(HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5) != HAL_OK)
   {
     /* Initialization Error */