Fix spacing after section header

Marlin/Configuration.h

@@ -596,6 +596,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 #define INVERT_E3_DIR false
 
 // @section homing
+
 //#define MIN_Z_HEIGHT_FOR_HOMING 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
                                     // Be sure you have this distance over your Z_MAX_POS in case.
 

Marlin/example_configurations/Cartesio/Configuration.h

@@ -596,6 +596,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 #define INVERT_E3_DIR false
 
 // @section homing
+
 //#define MIN_Z_HEIGHT_FOR_HOMING 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
                                     // Be sure you have this distance over your Z_MAX_POS in case.
 

Marlin/example_configurations/Felix/Configuration.h

@@ -578,6 +578,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 #define INVERT_E3_DIR false
 
 // @section homing
+
 //#define MIN_Z_HEIGHT_FOR_HOMING 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
                                     // Be sure you have this distance over your Z_MAX_POS in case.
 

Marlin/example_configurations/Felix/DUAL/Configuration.h

@@ -576,6 +576,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 #define INVERT_E3_DIR false
 
 // @section homing
+
 //#define MIN_Z_HEIGHT_FOR_HOMING 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
                                     // Be sure you have this distance over your Z_MAX_POS in case.
 

Marlin/example_configurations/Hephestos/Configuration.h

@@ -588,6 +588,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 #define INVERT_E3_DIR false
 
 // @section homing
+
 //#define MIN_Z_HEIGHT_FOR_HOMING 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
                                     // Be sure you have this distance over your Z_MAX_POS in case.
 

Marlin/example_configurations/Hephestos_2/Configuration.h

@@ -590,6 +590,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 #define INVERT_E3_DIR false
 
 // @section homing
+
 #define MIN_Z_HEIGHT_FOR_HOMING 5   // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
                                     // Be sure you have this distance over your Z_MAX_POS in case.
 

Marlin/example_configurations/K8200/Configuration.h

@@ -613,6 +613,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 #define INVERT_E3_DIR true
 
 // @section homing
+
 //#define MIN_Z_HEIGHT_FOR_HOMING 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
                                     // Be sure you have this distance over your Z_MAX_POS in case.
 

Marlin/example_configurations/K8400/Configuration.h

@@ -573,6 +573,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 #define INVERT_E3_DIR false
 
 // @section homing
+
 //#define MIN_Z_HEIGHT_FOR_HOMING 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
                                     // Be sure you have this distance over your Z_MAX_POS in case.
 

Marlin/example_configurations/K8400/Dual-head/Configuration.h

@@ -573,6 +573,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 #define INVERT_E3_DIR false
 
 // @section homing
+
 //#define MIN_Z_HEIGHT_FOR_HOMING 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
                                     // Be sure you have this distance over your Z_MAX_POS in case.
 

Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h

@@ -596,6 +596,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 #define INVERT_E3_DIR false
 
 // @section homing
+
 //#define MIN_Z_HEIGHT_FOR_HOMING 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
                                     // Be sure you have this distance over your Z_MAX_POS in case.
 

Marlin/example_configurations/RigidBot/Configuration.h

@@ -593,6 +593,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 #define INVERT_E3_DIR false
 
 // @section homing
+
 //#define MIN_Z_HEIGHT_FOR_HOMING 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
                                     // Be sure you have this distance over your Z_MAX_POS in case.
 

Marlin/example_configurations/SCARA/Configuration.h

@@ -604,6 +604,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 #define INVERT_E3_DIR false
 
 // @section homing
+
 //#define MIN_Z_HEIGHT_FOR_HOMING 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
                                     // Be sure you have this distance over your Z_MAX_POS in case.
 

Marlin/example_configurations/TAZ4/Configuration.h

@@ -617,6 +617,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 #define INVERT_E3_DIR true
 
 // @section homing
+
 //#define MIN_Z_HEIGHT_FOR_HOMING 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
                                     // Be sure you have this distance over your Z_MAX_POS in case.
 

Marlin/example_configurations/WITBOX/Configuration.h

@@ -588,6 +588,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 #define INVERT_E3_DIR false
 
 // @section homing
+
 //#define MIN_Z_HEIGHT_FOR_HOMING 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
                                     // Be sure you have this distance over your Z_MAX_POS in case.
 

Marlin/example_configurations/adafruit/ST7565/Configuration.h

@@ -596,6 +596,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 #define INVERT_E3_DIR false
 
 // @section homing
+
 //#define MIN_Z_HEIGHT_FOR_HOMING 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
                                     // Be sure you have this distance over your Z_MAX_POS in case.
 

Marlin/example_configurations/delta/biv2.5/Configuration.h

@@ -685,6 +685,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 #define INVERT_E3_DIR false
 
 // @section homing
+
 //#define MIN_Z_HEIGHT_FOR_HOMING 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
                                     // Be sure you have this distance over your Z_MAX_POS in case.
 

Marlin/example_configurations/delta/generic/Configuration.h

@@ -679,6 +679,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 #define INVERT_E3_DIR false
 
 // @section homing
+
 //#define MIN_Z_HEIGHT_FOR_HOMING 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
                                     // Be sure you have this distance over your Z_MAX_POS in case.
 

Marlin/example_configurations/delta/kossel_mini/Configuration.h

@@ -682,6 +682,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 #define INVERT_E3_DIR false
 
 // @section homing
+
 //#define MIN_Z_HEIGHT_FOR_HOMING 15// (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
                                     // Be sure you have this distance over your Z_MAX_POS in case.
 

Marlin/example_configurations/delta/kossel_pro/Configuration.h

@@ -676,6 +676,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 #define INVERT_E3_DIR false
 
 // @section homing
+
 //#define MIN_Z_HEIGHT_FOR_HOMING 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
                                     // Be sure you have this distance over your Z_MAX_POS in case.
 

Marlin/example_configurations/delta/kossel_xl/Configuration.h

@@ -677,6 +677,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 #define INVERT_E3_DIR false
 
 // @section homing
+
 //#define MIN_Z_HEIGHT_FOR_HOMING 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
                                     // Be sure you have this distance over your Z_MAX_POS in case.
 

Marlin/example_configurations/makibox/Configuration.h

@@ -599,6 +599,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 #define INVERT_E3_DIR false
 
 // @section homing
+
 //#define MIN_Z_HEIGHT_FOR_HOMING 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
                                     // Be sure you have this distance over your Z_MAX_POS in case.
 

Marlin/example_configurations/tvrrug/Round2/Configuration.h

@@ -586,6 +586,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 #define INVERT_E3_DIR false
 
 // @section homing
+
 //#define MIN_Z_HEIGHT_FOR_HOMING 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
                                     // Be sure you have this distance over your Z_MAX_POS in case.