Erik van der Zalm
13 years ago
7 changed files with 2019 additions and 1877 deletions
File diff suppressed because it is too large
@ -1,93 +1,96 @@ |
|||
/*
|
|||
planner.h - buffers movement commands and manages the acceleration profile plan |
|||
Part of Grbl |
|||
|
|||
Copyright (c) 2009-2011 Simen Svale Skogsrud |
|||
|
|||
Grbl is free software: you can redistribute it and/or modify |
|||
it under the terms of the GNU General Public License as published by |
|||
the Free Software Foundation, either version 3 of the License, or |
|||
(at your option) any later version. |
|||
|
|||
Grbl is distributed in the hope that it will be useful, |
|||
but WITHOUT ANY WARRANTY; without even the implied warranty of |
|||
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
|||
GNU General Public License for more details. |
|||
|
|||
You should have received a copy of the GNU General Public License |
|||
along with Grbl. If not, see <http://www.gnu.org/licenses/>.
|
|||
*/ |
|||
|
|||
// This module is to be considered a sub-module of stepper.c. Please don't include
|
|||
// this file from any other module.
|
|||
|
|||
#ifndef planner_h |
|||
#define planner_h |
|||
|
|||
#include "Configuration.h" |
|||
|
|||
// This struct is used when buffering the setup for each linear movement "nominal" values are as specified in
|
|||
// the source g-code and may never actually be reached if acceleration management is active.
|
|||
typedef struct { |
|||
// Fields used by the bresenham algorithm for tracing the line
|
|||
long steps_x, steps_y, steps_z, steps_e; // Step count along each axis
|
|||
long step_event_count; // The number of step events required to complete this block
|
|||
volatile long accelerate_until; // The index of the step event on which to stop acceleration
|
|||
volatile long decelerate_after; // The index of the step event on which to start decelerating
|
|||
volatile long acceleration_rate; // The acceleration rate used for acceleration calculation
|
|||
unsigned char direction_bits; // The direction bit set for this block (refers to *_DIRECTION_BIT in config.h)
|
|||
#ifdef ADVANCE |
|||
long advance_rate; |
|||
volatile long initial_advance; |
|||
volatile long final_advance; |
|||
float advance; |
|||
#endif |
|||
|
|||
// Fields used by the motion planner to manage acceleration
|
|||
float speed_x, speed_y, speed_z, speed_e; // Nominal mm/minute for each axis
|
|||
float nominal_speed; // The nominal speed for this block in mm/min
|
|||
float millimeters; // The total travel of this block in mm
|
|||
float entry_speed; |
|||
float acceleration; // acceleration mm/sec^2
|
|||
|
|||
// Settings for the trapezoid generator
|
|||
long nominal_rate; // The nominal step rate for this block in step_events/sec
|
|||
volatile long initial_rate; // The jerk-adjusted step rate at start of block
|
|||
volatile long final_rate; // The minimal rate at exit
|
|||
long acceleration_st; // acceleration steps/sec^2
|
|||
volatile char busy; |
|||
} block_t; |
|||
|
|||
// Initialize the motion plan subsystem
|
|||
void plan_init(); |
|||
|
|||
// Add a new linear movement to the buffer. x, y and z is the signed, absolute target position in
|
|||
// millimaters. Feed rate specifies the speed of the motion.
|
|||
void plan_buffer_line(const float &x, const float &y, const float &z, const float &e, float feed_rate); |
|||
|
|||
// Set position. Used for G92 instructions.
|
|||
void plan_set_position(const float &x, const float &y, const float &z, const float &e); |
|||
|
|||
|
|||
// Called when the current block is no longer needed. Discards the block and makes the memory
|
|||
// availible for new blocks.
|
|||
void plan_discard_current_block(); |
|||
|
|||
// Gets the current block. Returns NULL if buffer empty
|
|||
block_t *plan_get_current_block(); |
|||
|
|||
void check_axes_activity(); |
|||
|
|||
extern unsigned long minsegmenttime; |
|||
extern float max_feedrate[4]; // set the max speeds
|
|||
extern float axis_steps_per_unit[4]; |
|||
extern long max_acceleration_units_per_sq_second[4]; // Use M201 to override by software
|
|||
extern float minimumfeedrate; |
|||
extern float acceleration; // Normal acceleration mm/s^2 THIS IS THE DEFAULT ACCELERATION for all moves. M204 SXXXX
|
|||
extern float retract_acceleration; // mm/s^2 filament pull-pack and push-forward while standing still in the other axis M204 TXXXX
|
|||
extern float max_xy_jerk; //speed than can be stopped at once, if i understand correctly.
|
|||
extern float max_z_jerk; |
|||
extern float mintravelfeedrate; |
|||
extern unsigned long axis_steps_per_sqr_second[NUM_AXIS]; |
|||
|
|||
/*
|
|||
planner.h - buffers movement commands and manages the acceleration profile plan |
|||
Part of Grbl |
|||
|
|||
Copyright (c) 2009-2011 Simen Svale Skogsrud |
|||
|
|||
Grbl is free software: you can redistribute it and/or modify |
|||
it under the terms of the GNU General Public License as published by |
|||
the Free Software Foundation, either version 3 of the License, or |
|||
(at your option) any later version. |
|||
|
|||
Grbl is distributed in the hope that it will be useful, |
|||
but WITHOUT ANY WARRANTY; without even the implied warranty of |
|||
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
|||
GNU General Public License for more details. |
|||
|
|||
You should have received a copy of the GNU General Public License |
|||
along with Grbl. If not, see <http://www.gnu.org/licenses/>.
|
|||
*/ |
|||
|
|||
// This module is to be considered a sub-module of stepper.c. Please don't include
|
|||
// this file from any other module.
|
|||
|
|||
#ifndef planner_h |
|||
#define planner_h |
|||
|
|||
#include "Configuration.h" |
|||
|
|||
// This struct is used when buffering the setup for each linear movement "nominal" values are as specified in
|
|||
// the source g-code and may never actually be reached if acceleration management is active.
|
|||
typedef struct { |
|||
// Fields used by the bresenham algorithm for tracing the line
|
|||
long steps_x, steps_y, steps_z, steps_e; // Step count along each axis
|
|||
long step_event_count; // The number of step events required to complete this block
|
|||
volatile long accelerate_until; // The index of the step event on which to stop acceleration
|
|||
volatile long decelerate_after; // The index of the step event on which to start decelerating
|
|||
volatile long acceleration_rate; // The acceleration rate used for acceleration calculation
|
|||
unsigned char direction_bits; // The direction bit set for this block (refers to *_DIRECTION_BIT in config.h)
|
|||
#ifdef ADVANCE |
|||
// long advance_rate;
|
|||
// volatile long initial_advance;
|
|||
// volatile long final_advance;
|
|||
// float advance;
|
|||
#endif |
|||
|
|||
// Fields used by the motion planner to manage acceleration
|
|||
// float speed_x, speed_y, speed_z, speed_e; // Nominal mm/minute for each axis
|
|||
float nominal_speed; // The nominal speed for this block in mm/min
|
|||
float entry_speed; // Entry speed at previous-current junction in mm/min
|
|||
float max_entry_speed; // Maximum allowable junction entry speed in mm/min
|
|||
float millimeters; // The total travel of this block in mm
|
|||
float acceleration; // acceleration mm/sec^2
|
|||
unsigned char recalculate_flag; // Planner flag to recalculate trapezoids on entry junction
|
|||
unsigned char nominal_length_flag; // Planner flag for nominal speed always reached
|
|||
|
|||
// Settings for the trapezoid generator
|
|||
long nominal_rate; // The nominal step rate for this block in step_events/sec
|
|||
volatile long initial_rate; // The jerk-adjusted step rate at start of block
|
|||
volatile long final_rate; // The minimal rate at exit
|
|||
long acceleration_st; // acceleration steps/sec^2
|
|||
volatile char busy; |
|||
} block_t; |
|||
|
|||
// Initialize the motion plan subsystem
|
|||
void plan_init(); |
|||
|
|||
// Add a new linear movement to the buffer. x, y and z is the signed, absolute target position in
|
|||
// millimaters. Feed rate specifies the speed of the motion.
|
|||
void plan_buffer_line(const float &x, const float &y, const float &z, const float &e, float feed_rate); |
|||
|
|||
// Set position. Used for G92 instructions.
|
|||
void plan_set_position(const float &x, const float &y, const float &z, const float &e); |
|||
|
|||
|
|||
// Called when the current block is no longer needed. Discards the block and makes the memory
|
|||
// availible for new blocks.
|
|||
void plan_discard_current_block(); |
|||
|
|||
// Gets the current block. Returns NULL if buffer empty
|
|||
block_t *plan_get_current_block(); |
|||
|
|||
void check_axes_activity(); |
|||
|
|||
extern unsigned long minsegmenttime; |
|||
extern float max_feedrate[4]; // set the max speeds
|
|||
extern float axis_steps_per_unit[4]; |
|||
extern long max_acceleration_units_per_sq_second[4]; // Use M201 to override by software
|
|||
extern float minimumfeedrate; |
|||
extern float acceleration; // Normal acceleration mm/s^2 THIS IS THE DEFAULT ACCELERATION for all moves. M204 SXXXX
|
|||
extern float retract_acceleration; // mm/s^2 filament pull-pack and push-forward while standing still in the other axis M204 TXXXX
|
|||
extern float max_xy_jerk; //speed than can be stopped at once, if i understand correctly.
|
|||
extern float max_z_jerk; |
|||
extern float mintravelfeedrate; |
|||
extern unsigned long axis_steps_per_sqr_second[NUM_AXIS]; |
|||
|
|||
#endif |
|||
|
|||
File diff suppressed because it is too large
File diff suppressed because it is too large
Loading…
Reference in new issue