Neil Darlow 10 years ago
parent
commit
64139f5e5a
  1. 14
      .travis.yml
  2. 4
      Marlin/Configuration.h
  3. 6
      Marlin/Configuration_adv.h
  4. 204
      Marlin/DOGMbitmaps.h
  5. 35
      Marlin/Marlin_main.cpp
  6. 6
      Marlin/dogm_lcd_implementation.h
  7. 163
      Marlin/example_configurations/delta/Configuration.h
  8. 15
      Marlin/example_configurations/delta/Configuration_adv.h
  9. 16
      Marlin/language.h
  10. 53
      Marlin/stepper.cpp
  11. 29
      Marlin/ultralcd.cpp
  12. 2
      Marlin/ultralcd.h
  13. 1
      README.md

14
.travis.yml

@ -0,0 +1,14 @@
---
language: c
before_install:
- sudo add-apt-repository -y ppa:ubuntu-toolchain-r/test
- sudo apt-get update -qq
install:
- sudo apt-get install -qq gcc-avr binutils-avr avr-libc gcc-4.8 g++-4.8 arduino
- sudo update-alternatives --install /usr/bin/gcc gcc /usr/bin/gcc-4.8 90
- sudo update-alternatives --install /usr/bin/g++ g++ /usr/bin/g++-4.8 90
- gcc --version
- g++ --version
script: "cd Marlin && make HARDWARE_MOTHERBOARD=70 ARDUINO_INSTALL_DIR=/usr/share/arduino"

4
Marlin/Configuration.h

@ -777,7 +777,9 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
* 301 - Rambo - uses Analog input 3
* Note may require analog pins to be defined for different motherboards
**********************************************************************/
#define FILAMENT_SENSOR
// Uncomment below to enable
//#define FILAMENT_SENSOR
#define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2)
#define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel

6
Marlin/Configuration_adv.h

@ -219,9 +219,11 @@
//#define QUICK_HOME //if this is defined, if both x and y are to be homed, a diagonal move will be performed initially.
#define AXIS_RELATIVE_MODES {false, false, false, false}
#ifdef CONFIG_STEPPERS_TOSHIBA
#define MAX_STEP_FREQUENCY 10000 // Max step frequency for Toshiba Stepper Controllers
#else
#define MAX_STEP_FREQUENCY 40000 // Max step frequency for Ultimaker (5000 pps / half step)
#endif
//By default pololu step drivers require an active high signal. However, some high power drivers require an active low signal as step.
#define INVERT_X_STEP_PIN false
#define INVERT_Y_STEP_PIN false

204
Marlin/DOGMbitmaps.h

@ -68,54 +68,162 @@ const unsigned char start_bmp[574] PROGMEM = { //AVR-GCC, WinAVR
0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xF0
};
#define STATUS_SCREENWIDTH 115 //Width in pixels
#define STATUS_SCREENHEIGHT 19 //Height in pixels
#define STATUS_SCREENBYTEWIDTH 15 //Width in bytes
const unsigned char status_screen0_bmp[] PROGMEM = { //AVR-GCC, WinAVR
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x7F,0xFF,0xE0,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x70,0x00,0xE0,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x63,0x0C,0x60,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x47,0x0E,0x20,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x4F,0x0F,0x20,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x5F,0x0F,0xA0,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x5E,0x07,0xA0,
0x7F,0x80,0x00,0x3F,0xC0,0x00,0x3F,0xC0,0x00,0x41,0x04,0x00,0x40,0x60,0x20,
0xFB,0xC0,0x00,0x79,0xE0,0x00,0x79,0xE0,0x00,0x20,0x82,0x00,0x40,0xF0,0x20,
0xF3,0xC0,0x00,0x76,0xE0,0x00,0x76,0xE0,0x00,0x20,0x82,0x00,0x40,0xF0,0x20,
0xEB,0xC0,0x00,0x7E,0xE0,0x00,0x7E,0xE0,0x00,0x41,0x04,0x00,0x40,0x60,0x20,
0x7B,0x80,0x00,0x3D,0xC0,0x00,0x39,0xC0,0x00,0x82,0x08,0x00,0x5E,0x07,0xA0,
0x7B,0x80,0x00,0x3B,0xC0,0x00,0x3E,0xC0,0x01,0x04,0x10,0x00,0x5F,0x0F,0xA0,
0xFB,0xC0,0x00,0x77,0xE0,0x00,0x76,0xE0,0x01,0x04,0x10,0x00,0x4F,0x0F,0x20,
0xFB,0xC0,0x00,0x70,0xE0,0x00,0x79,0xE0,0x00,0x82,0x08,0x00,0x47,0x0E,0x20,
0xFF,0xC0,0x00,0x7F,0xE0,0x00,0x7F,0xE0,0x00,0x41,0x04,0x00,0x63,0x0C,0x60,
0x3F,0x00,0x00,0x1F,0x80,0x00,0x1F,0x80,0x00,0x00,0x00,0x00,0x70,0x00,0xE0,
0x1E,0x00,0x00,0x0F,0x00,0x00,0x0F,0x00,0x01,0xFF,0xFF,0x80,0x7F,0xFF,0xE0,
0x0C,0x00,0x00,0x06,0x00,0x00,0x06,0x00,0x01,0xFF,0xFF,0x80,0x00,0x00,0x00
};
// Here comes a compile-time operation to match the extruder symbols
// on the info screen to the set number of extruders in configuration.h
//
// When only one extruder is selected, the "1" on the symbol will not
// be displayed.
#define STATUS_SCREENWIDTH 115 //Width in pixels
#define STATUS_SCREENHEIGHT 19 //Height in pixels
#define STATUS_SCREENBYTEWIDTH 15 //Width in bytes
const unsigned char status_screen1_bmp[] PROGMEM = { //AVR-GCC, WinAVR
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x7F,0xFF,0xE0,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x70,0x00,0xE0,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x61,0xF8,0x60,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x41,0xF8,0x20,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x40,0xF0,0x20,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x40,0x60,0x20,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x58,0x01,0xA0,
0x7F,0x80,0x00,0x3F,0xC0,0x00,0x3F,0xC0,0x00,0x41,0x04,0x00,0x5C,0x63,0xA0,
0xFB,0xC0,0x00,0x79,0xE0,0x00,0x79,0xE0,0x00,0x20,0x82,0x00,0x5E,0xF7,0xA0,
0xF3,0xC0,0x00,0x76,0xE0,0x00,0x76,0xE0,0x00,0x20,0x82,0x00,0x5E,0xF7,0xA0,
0xEB,0xC0,0x00,0x7E,0xE0,0x00,0x7E,0xE0,0x00,0x41,0x04,0x00,0x5C,0x63,0xA0,
0x7B,0x80,0x00,0x3D,0xC0,0x00,0x39,0xC0,0x00,0x82,0x08,0x00,0x58,0x01,0xA0,
0x7B,0x80,0x00,0x3B,0xC0,0x00,0x3E,0xC0,0x01,0x04,0x10,0x00,0x40,0x60,0x20,
0xFB,0xC0,0x00,0x77,0xE0,0x00,0x76,0xE0,0x01,0x04,0x10,0x00,0x40,0xF0,0x20,
0xFB,0xC0,0x00,0x70,0xE0,0x00,0x79,0xE0,0x00,0x82,0x08,0x00,0x41,0xF8,0x20,
0xFF,0xC0,0x00,0x7F,0xE0,0x00,0x7F,0xE0,0x00,0x41,0x04,0x00,0x61,0xF8,0x60,
0x3F,0x00,0x00,0x1F,0x80,0x00,0x1F,0x80,0x00,0x00,0x00,0x00,0x70,0x00,0xE0,
0x1E,0x00,0x00,0x0F,0x00,0x00,0x0F,0x00,0x01,0xFF,0xFF,0x80,0x7F,0xFF,0xE0,
0x0C,0x00,0x00,0x06,0x00,0x00,0x06,0x00,0x01,0xFF,0xFF,0x80,0x00,0x00,0x00
};
#if EXTRUDERS == 1
#define STATUS_SCREENWIDTH 115 //Width in pixels
#define STATUS_SCREENHEIGHT 19 //Height in pixels
#define STATUS_SCREENBYTEWIDTH 15 //Width in bytes
const unsigned char status_screen0_bmp[] PROGMEM = { //AVR-GCC, WinAVR
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x7F,0xFF,0xE0,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x70,0x00,0xE0,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x63,0x0C,0x60,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x47,0x0E,0x20,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x4F,0x0F,0x20,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x5F,0x0F,0xA0,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x5E,0x07,0xA0,
0x7F,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x41,0x04,0x00,0x40,0x60,0x20,
0xFF,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x20,0x82,0x00,0x40,0xF0,0x20,
0xFF,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x20,0x82,0x00,0x40,0xF0,0x20,
0xFF,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x41,0x04,0x00,0x40,0x60,0x20,
0x7F,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x82,0x08,0x00,0x5E,0x07,0xA0,
0x7F,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x04,0x10,0x00,0x5F,0x0F,0xA0,
0xFF,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x04,0x10,0x00,0x4F,0x0F,0x20,
0xFF,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x82,0x08,0x00,0x47,0x0E,0x20,
0xFF,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x41,0x04,0x00,0x63,0x0C,0x60,
0x3F,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x70,0x00,0xE0,
0x1E,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0xFF,0xFF,0x80,0x7F,0xFF,0xE0,
0x0C,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0xFF,0xFF,0x80,0x00,0x00,0x00
};
#define STATUS_SCREENWIDTH 115 //Width in pixels
#define STATUS_SCREENHEIGHT 19 //Height in pixels
#define STATUS_SCREENBYTEWIDTH 15 //Width in bytes
const unsigned char status_screen1_bmp[] PROGMEM = { //AVR-GCC, WinAVR
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x7F,0xFF,0xE0,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x70,0x00,0xE0,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x61,0xF8,0x60,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x41,0xF8,0x20,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x40,0xF0,0x20,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x40,0x60,0x20,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x58,0x01,0xA0,
0x7F,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x41,0x04,0x00,0x5C,0x63,0xA0,
0xFF,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x20,0x82,0x00,0x5E,0xF7,0xA0,
0xFF,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x20,0x82,0x00,0x5E,0xF7,0xA0,
0xFF,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x41,0x04,0x00,0x5C,0x63,0xA0,
0x7F,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x82,0x08,0x00,0x58,0x01,0xA0,
0x7F,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x04,0x10,0x00,0x40,0x60,0x20,
0xFF,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x04,0x10,0x00,0x40,0xF0,0x20,
0xFF,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x82,0x08,0x00,0x41,0xF8,0x20,
0xFF,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x41,0x04,0x00,0x61,0xF8,0x60,
0x3F,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x70,0x00,0xE0,
0x1E,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0xFF,0xFF,0x80,0x7F,0xFF,0xE0,
0x0C,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0xFF,0xFF,0x80,0x00,0x00,0x00
};
#elif EXTRUDERS == 2
#define STATUS_SCREENWIDTH 115 //Width in pixels
#define STATUS_SCREENHEIGHT 19 //Height in pixels
#define STATUS_SCREENBYTEWIDTH 15 //Width in bytes
const unsigned char status_screen0_bmp[] PROGMEM = { //AVR-GCC, WinAVR
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x7F,0xFF,0xE0,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x70,0x00,0xE0,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x63,0x0C,0x60,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x47,0x0E,0x20,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x4F,0x0F,0x20,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x5F,0x0F,0xA0,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x5E,0x07,0xA0,
0x7F,0x80,0x00,0x3F,0xC0,0x00,0x00,0x00,0x00,0x41,0x04,0x00,0x40,0x60,0x20,
0xFB,0xC0,0x00,0x79,0xE0,0x00,0x00,0x00,0x00,0x20,0x82,0x00,0x40,0xF0,0x20,
0xF3,0xC0,0x00,0x76,0xE0,0x00,0x00,0x00,0x00,0x20,0x82,0x00,0x40,0xF0,0x20,
0xEB,0xC0,0x00,0x7E,0xE0,0x00,0x00,0x00,0x00,0x41,0x04,0x00,0x40,0x60,0x20,
0x7B,0x80,0x00,0x3D,0xC0,0x00,0x00,0x00,0x00,0x82,0x08,0x00,0x5E,0x07,0xA0,
0x7B,0x80,0x00,0x3B,0xC0,0x00,0x00,0x00,0x01,0x04,0x10,0x00,0x5F,0x0F,0xA0,
0xFB,0xC0,0x00,0x77,0xE0,0x00,0x00,0x00,0x01,0x04,0x10,0x00,0x4F,0x0F,0x20,
0xFB,0xC0,0x00,0x70,0xE0,0x00,0x00,0x00,0x00,0x82,0x08,0x00,0x47,0x0E,0x20,
0xFF,0xC0,0x00,0x7F,0xE0,0x00,0x00,0x00,0x00,0x41,0x04,0x00,0x63,0x0C,0x60,
0x3F,0x00,0x00,0x1F,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x70,0x00,0xE0,
0x1E,0x00,0x00,0x0F,0x00,0x00,0x00,0x00,0x01,0xFF,0xFF,0x80,0x7F,0xFF,0xE0,
0x0C,0x00,0x00,0x06,0x00,0x00,0x00,0x00,0x01,0xFF,0xFF,0x80,0x00,0x00,0x00
};
#define STATUS_SCREENWIDTH 115 //Width in pixels
#define STATUS_SCREENHEIGHT 19 //Height in pixels
#define STATUS_SCREENBYTEWIDTH 15 //Width in bytes
const unsigned char status_screen1_bmp[] PROGMEM = { //AVR-GCC, WinAVR
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x7F,0xFF,0xE0,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x70,0x00,0xE0,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x61,0xF8,0x60,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x41,0xF8,0x20,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x40,0xF0,0x20,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x40,0x60,0x20,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x58,0x01,0xA0,
0x7F,0x80,0x00,0x3F,0xC0,0x00,0x00,0x00,0x00,0x41,0x04,0x00,0x5C,0x63,0xA0,
0xFB,0xC0,0x00,0x79,0xE0,0x00,0x00,0x00,0x00,0x20,0x82,0x00,0x5E,0xF7,0xA0,
0xF3,0xC0,0x00,0x76,0xE0,0x00,0x00,0x00,0x00,0x20,0x82,0x00,0x5E,0xF7,0xA0,
0xEB,0xC0,0x00,0x7E,0xE0,0x00,0x00,0x00,0x00,0x41,0x04,0x00,0x5C,0x63,0xA0,
0x7B,0x80,0x00,0x3D,0xC0,0x00,0x00,0x00,0x00,0x82,0x08,0x00,0x58,0x01,0xA0,
0x7B,0x80,0x00,0x3B,0xC0,0x00,0x00,0x00,0x01,0x04,0x10,0x00,0x40,0x60,0x20,
0xFB,0xC0,0x00,0x77,0xE0,0x00,0x00,0x00,0x01,0x04,0x10,0x00,0x40,0xF0,0x20,
0xFB,0xC0,0x00,0x70,0xE0,0x00,0x00,0x00,0x00,0x82,0x08,0x00,0x41,0xF8,0x20,
0xFF,0xC0,0x00,0x7F,0xE0,0x00,0x00,0x00,0x00,0x41,0x04,0x00,0x61,0xF8,0x60,
0x3F,0x00,0x00,0x1F,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x70,0x00,0xE0,
0x1E,0x00,0x00,0x0F,0x00,0x00,0x00,0x00,0x01,0xFF,0xFF,0x80,0x7F,0xFF,0xE0,
0x0C,0x00,0x00,0x06,0x00,0x00,0x00,0x00,0x01,0xFF,0xFF,0x80,0x00,0x00,0x00
};
#else
#define STATUS_SCREENWIDTH 115 //Width in pixels
#define STATUS_SCREENHEIGHT 19 //Height in pixels
#define STATUS_SCREENBYTEWIDTH 15 //Width in bytes
const unsigned char status_screen0_bmp[] PROGMEM = { //AVR-GCC, WinAVR
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x7F,0xFF,0xE0,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x70,0x00,0xE0,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x63,0x0C,0x60,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x47,0x0E,0x20,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x4F,0x0F,0x20,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x5F,0x0F,0xA0,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x5E,0x07,0xA0,
0x7F,0x80,0x00,0x3F,0xC0,0x00,0x3F,0xC0,0x00,0x41,0x04,0x00,0x40,0x60,0x20,
0xFB,0xC0,0x00,0x79,0xE0,0x00,0x79,0xE0,0x00,0x20,0x82,0x00,0x40,0xF0,0x20,
0xF3,0xC0,0x00,0x76,0xE0,0x00,0x76,0xE0,0x00,0x20,0x82,0x00,0x40,0xF0,0x20,
0xEB,0xC0,0x00,0x7E,0xE0,0x00,0x7E,0xE0,0x00,0x41,0x04,0x00,0x40,0x60,0x20,
0x7B,0x80,0x00,0x3D,0xC0,0x00,0x39,0xC0,0x00,0x82,0x08,0x00,0x5E,0x07,0xA0,
0x7B,0x80,0x00,0x3B,0xC0,0x00,0x3E,0xC0,0x01,0x04,0x10,0x00,0x5F,0x0F,0xA0,
0xFB,0xC0,0x00,0x77,0xE0,0x00,0x76,0xE0,0x01,0x04,0x10,0x00,0x4F,0x0F,0x20,
0xFB,0xC0,0x00,0x70,0xE0,0x00,0x79,0xE0,0x00,0x82,0x08,0x00,0x47,0x0E,0x20,
0xFF,0xC0,0x00,0x7F,0xE0,0x00,0x7F,0xE0,0x00,0x41,0x04,0x00,0x63,0x0C,0x60,
0x3F,0x00,0x00,0x1F,0x80,0x00,0x1F,0x80,0x00,0x00,0x00,0x00,0x70,0x00,0xE0,
0x1E,0x00,0x00,0x0F,0x00,0x00,0x0F,0x00,0x01,0xFF,0xFF,0x80,0x7F,0xFF,0xE0,
0x0C,0x00,0x00,0x06,0x00,0x00,0x06,0x00,0x01,0xFF,0xFF,0x80,0x00,0x00,0x00
};
#define STATUS_SCREENWIDTH 115 //Width in pixels
#define STATUS_SCREENHEIGHT 19 //Height in pixels
#define STATUS_SCREENBYTEWIDTH 15 //Width in bytes
const unsigned char status_screen1_bmp[] PROGMEM = { //AVR-GCC, WinAVR
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x7F,0xFF,0xE0,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x70,0x00,0xE0,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x61,0xF8,0x60,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x41,0xF8,0x20,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x40,0xF0,0x20,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x40,0x60,0x20,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x58,0x01,0xA0,
0x7F,0x80,0x00,0x3F,0xC0,0x00,0x3F,0xC0,0x00,0x41,0x04,0x00,0x5C,0x63,0xA0,
0xFB,0xC0,0x00,0x79,0xE0,0x00,0x79,0xE0,0x00,0x20,0x82,0x00,0x5E,0xF7,0xA0,
0xF3,0xC0,0x00,0x76,0xE0,0x00,0x76,0xE0,0x00,0x20,0x82,0x00,0x5E,0xF7,0xA0,
0xEB,0xC0,0x00,0x7E,0xE0,0x00,0x7E,0xE0,0x00,0x41,0x04,0x00,0x5C,0x63,0xA0,
0x7B,0x80,0x00,0x3D,0xC0,0x00,0x39,0xC0,0x00,0x82,0x08,0x00,0x58,0x01,0xA0,
0x7B,0x80,0x00,0x3B,0xC0,0x00,0x3E,0xC0,0x01,0x04,0x10,0x00,0x40,0x60,0x20,
0xFB,0xC0,0x00,0x77,0xE0,0x00,0x76,0xE0,0x01,0x04,0x10,0x00,0x40,0xF0,0x20,
0xFB,0xC0,0x00,0x70,0xE0,0x00,0x79,0xE0,0x00,0x82,0x08,0x00,0x41,0xF8,0x20,
0xFF,0xC0,0x00,0x7F,0xE0,0x00,0x7F,0xE0,0x00,0x41,0x04,0x00,0x61,0xF8,0x60,
0x3F,0x00,0x00,0x1F,0x80,0x00,0x1F,0x80,0x00,0x00,0x00,0x00,0x70,0x00,0xE0,
0x1E,0x00,0x00,0x0F,0x00,0x00,0x0F,0x00,0x01,0xFF,0xFF,0x80,0x7F,0xFF,0xE0,
0x0C,0x00,0x00,0x06,0x00,0x00,0x06,0x00,0x01,0xFF,0xFF,0x80,0x00,0x00,0x00
};
#endif // Extruders

35
Marlin/Marlin_main.cpp

@ -1385,7 +1385,7 @@ void process_commands()
st_synchronize();
codenum += millis(); // keep track of when we started waiting
previous_millis_cmd = millis();
while(millis() < codenum ){
while(millis() < codenum) {
manage_heater();
manage_inactivity();
lcd_update();
@ -1413,7 +1413,6 @@ void process_commands()
plan_bed_level_matrix.set_to_identity(); //Reset the plane ("erase" all leveling data)
#endif //ENABLE_AUTO_BED_LEVELING
saved_feedrate = feedrate;
saved_feedmultiply = feedmultiply;
feedmultiply = 100;
@ -1863,20 +1862,39 @@ void process_commands()
case 0: // M0 - Unconditional stop - Wait for user button press on LCD
case 1: // M1 - Conditional stop - Wait for user button press on LCD
{
LCD_MESSAGEPGM(MSG_USERWAIT);
char *src = strchr_pointer + 2;
codenum = 0;
if(code_seen('P')) codenum = code_value(); // milliseconds to wait
if(code_seen('S')) codenum = code_value() * 1000; // seconds to wait
bool hasP = false, hasS = false;
if (code_seen('P')) {
codenum = code_value(); // milliseconds to wait
hasP = codenum > 0;
}
if (code_seen('S')) {
codenum = code_value() * 1000; // seconds to wait
hasS = codenum > 0;
}
starpos = strchr(src, '*');
if (starpos != NULL) *(starpos) = '\0';
while (*src == ' ') ++src;
if (!hasP && !hasS && *src != '\0') {
lcd_setstatus(src);
} else {
LCD_MESSAGEPGM(MSG_USERWAIT);
}
lcd_ignore_click();
st_synchronize();
previous_millis_cmd = millis();
if (codenum > 0){
codenum += millis(); // keep track of when we started waiting
while(millis() < codenum && !lcd_clicked()){
while(millis() < codenum && !lcd_clicked()){
manage_heater();
manage_inactivity();
lcd_update();
}
lcd_ignore_click(false);
}else{
if (!lcd_detected())
break;
@ -1886,7 +1904,10 @@ void process_commands()
lcd_update();
}
}
LCD_MESSAGEPGM(MSG_RESUMING);
if (IS_SD_PRINTING)
LCD_MESSAGEPGM(MSG_RESUMING);
else
LCD_MESSAGEPGM(WELCOME_MSG);
}
break;
#endif

6
Marlin/dogm_lcd_implementation.h

@ -245,9 +245,6 @@ static void lcd_implementation_status_screen()
u8g.drawBox(38,17,2,2);
u8g.setColorIndex(1); // black on white
}
#else
u8g.setPrintPos(31,27);
u8g.print("---");
#endif
// Extruder 3
@ -266,9 +263,6 @@ static void lcd_implementation_status_screen()
u8g.drawBox(62,17,2,2);
u8g.setColorIndex(1); // black on white
}
#else
u8g.setPrintPos(55,27);
u8g.print("---");
#endif
// Heatbed

163
Marlin/example_configurations/delta/Configuration.h

@ -41,6 +41,7 @@
// 33 = RAMPS 1.3 / 1.4 (Power outputs: Extruder, Fan, Bed)
// 34 = RAMPS 1.3 / 1.4 (Power outputs: Extruder0, Extruder1, Bed)
// 35 = RAMPS 1.3 / 1.4 (Power outputs: Extruder, Fan, Fan)
// 36 = RAMPS 1.3 / 1.4 (Power outputs: Extruder0, Extruder1, Fan)
// 4 = Duemilanove w/ ATMega328P pin assignment
// 5 = Gen6
// 51 = Gen6 deluxe
@ -54,12 +55,14 @@
// 68 = Azteeg X3 Pro
// 7 = Ultimaker
// 71 = Ultimaker (Older electronics. Pre 1.5.4. This is rare)
// 72 = Ultimainboard 2.x (Uses TEMP_SENSOR 20)
// 77 = 3Drag Controller
// 8 = Teensylu
// 80 = Rumba
// 81 = Printrboard (AT90USB1286)
// 82 = Brainwave (AT90USB646)
// 83 = SAV Mk-I (AT90USB1286)
// 84 = Teensy++2.0 (AT90USB1286) // CLI compile: DEFINES=AT90USBxx_TEENSYPP_ASSIGNMENTS HARDWARE_MOTHERBOARD=84 make
// 9 = Gen3+
// 70 = Megatronics
// 701= Megatronics v2.0
@ -68,6 +71,8 @@
// 91 = Final OMCA board
// 301= Rambo
// 21 = Elefu Ra Board (v3)
// 88 = 5DPrint D8 Driver Board
// 999 = Leapfrog
#ifndef MOTHERBOARD
#define MOTHERBOARD 33
@ -141,7 +146,11 @@
// 8 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
// 9 is 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
// 10 is 100k RS thermistor 198-961 (4.7k pullup)
// 60 is 100k Maker's Tool Works Kapton Bed Thermistor
// 11 is 100k beta 3950 1% thermistor (4.7k pullup)
// 12 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
// 13 is 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
// 20 is the PT100 circuit found in the Ultimainboard V2.x
// 60 is 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
//
// 1k ohm pullup tables - This is not normal, you would have to have changed out your 4.7k for 1k
// (but gives greater accuracy and more stable PID)
@ -205,7 +214,7 @@
// is more then PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
#define PID_INTEGRAL_DRIVE_MAX 255 //limit for the integral term
#define K1 0.95 //smoothing factor within the PID
#define PID_dT ((16.0 * 8.0)/(F_CPU / 64.0 / 256.0)) //sampling period of the temperature routine
#define PID_dT ((OVERSAMPLENR * 10.0)/(F_CPU / 64.0 / 256.0)) //sampling period of the temperature routine
// If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
// Ultimaker
@ -271,6 +280,44 @@
#define EXTRUDE_MINTEMP 170
#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances.
/*================== Thermal Runaway Protection ==============================
This is a feature to protect your printer from burn up in flames if it has
a thermistor coming off place (this happened to a friend of mine recently and
motivated me writing this feature).
The issue: If a thermistor come off, it will read a lower temperature than actual.
The system will turn the heater on forever, burning up the filament and anything
else around.
After the temperature reaches the target for the first time, this feature will
start measuring for how long the current temperature stays below the target
minus _HYSTERESIS (set_temperature - THERMAL_RUNAWAY_PROTECTION_HYSTERESIS).
If it stays longer than _PERIOD, it means the thermistor temperature
cannot catch up with the target, so something *may be* wrong. Then, to be on the
safe side, the system will he halt.
Bear in mind the count down will just start AFTER the first time the
thermistor temperature is over the target, so you will have no problem if
your extruder heater takes 2 minutes to hit the target on heating.
*/
// If you want to enable this feature for all your extruder heaters,
// uncomment the 2 defines below:
// Parameters for all extruder heaters
//#define THERMAL_RUNAWAY_PROTECTION_PERIOD 40 //in seconds
//#define THERMAL_RUNAWAY_PROTECTION_HYSTERESIS 4 // in degree Celsius
// If you want to enable this feature for your bed heater,
// uncomment the 2 defines below:
// Parameters for the bed heater
//#define THERMAL_RUNAWAY_PROTECTION_BED_PERIOD 20 //in seconds
//#define THERMAL_RUNAWAY_PROTECTION_BED_HYSTERESIS 2 // in degree Celsius
//===========================================================================
//===========================================================================
//=============================Mechanical Settings===========================
//===========================================================================
@ -326,6 +373,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
#define DISABLE_Y false
#define DISABLE_Z false
#define DISABLE_E false // For all extruders
#define DISABLE_INACTIVE_EXTRUDER true //disable only inactive extruders and keep active extruder enabled
#define INVERT_X_DIR false // DELTA does not invert
#define INVERT_Y_DIR false
@ -359,14 +407,53 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
//============================= Bed Auto Leveling ===========================
//#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line)
#define Z_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
#ifdef ENABLE_AUTO_BED_LEVELING
// these are the positions on the bed to do the probing
#define LEFT_PROBE_BED_POSITION 15
#define RIGHT_PROBE_BED_POSITION 170
#define BACK_PROBE_BED_POSITION 180
#define FRONT_PROBE_BED_POSITION 20
// There are 2 different ways to pick the X and Y locations to probe:
// - "grid" mode
// Probe every point in a rectangular grid
// You must specify the rectangle, and the density of sample points
// This mode is preferred because there are more measurements.
// It used to be called ACCURATE_BED_LEVELING but "grid" is more descriptive
// - "3-point" mode
// Probe 3 arbitrary points on the bed (that aren't colinear)
// You must specify the X & Y coordinates of all 3 points
#define AUTO_BED_LEVELING_GRID
// with AUTO_BED_LEVELING_GRID, the bed is sampled in a
// AUTO_BED_LEVELING_GRID_POINTSxAUTO_BED_LEVELING_GRID_POINTS grid
// and least squares solution is calculated
// Note: this feature occupies 10'206 byte
#ifdef AUTO_BED_LEVELING_GRID
// set the rectangle in which to probe
#define LEFT_PROBE_BED_POSITION 15
#define RIGHT_PROBE_BED_POSITION 170
#define BACK_PROBE_BED_POSITION 180
#define FRONT_PROBE_BED_POSITION 20
// set the number of grid points per dimension
// I wouldn't see a reason to go above 3 (=9 probing points on the bed)
#define AUTO_BED_LEVELING_GRID_POINTS 2
#else // not AUTO_BED_LEVELING_GRID
// with no grid, just probe 3 arbitrary points. A simple cross-product
// is used to esimate the plane of the print bed
#define ABL_PROBE_PT_1_X 15
#define ABL_PROBE_PT_1_Y 180
#define ABL_PROBE_PT_2_X 15
#define ABL_PROBE_PT_2_Y 20
#define ABL_PROBE_PT_3_X 170
#define ABL_PROBE_PT_3_Y 20
#endif // AUTO_BED_LEVELING_GRID
// these are the offsets to the probe relative to the extruder tip (Hotend - Probe)
#define X_PROBE_OFFSET_FROM_EXTRUDER -25
@ -381,6 +468,8 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
#define Z_RAISE_BEFORE_PROBING 15 //How much the extruder will be raised before traveling to the first probing point.
#define Z_RAISE_BETWEEN_PROBINGS 5 //How much the extruder will be raised when traveling from between next probing points
//#define Z_PROBE_SLED // turn on if you have a z-probe mounted on a sled like those designed by Charles Bell
//#define SLED_DOCKING_OFFSET 5 // the extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
//If defined, the Probe servo will be turned on only during movement and then turned off to avoid jerk
//The value is the delay to turn the servo off after powered on - depends on the servo speed; 300ms is good value, but you can try lower it.
@ -406,7 +495,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
#endif
#endif
#endif // ENABLE_AUTO_BED_LEVELING
// The position of the homing switches
@ -451,6 +540,15 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
//=============================Additional Features===========================
//===========================================================================
// Custom M code points
#define CUSTOM_M_CODES
#ifdef CUSTOM_M_CODES
#define CUSTOM_M_CODE_SET_Z_PROBE_OFFSET 851
#define Z_PROBE_OFFSET_RANGE_MIN -15
#define Z_PROBE_OFFSET_RANGE_MAX -5
#endif
// EEPROM
// The microcontroller can store settings in the EEPROM, e.g. max velocity...
// M500 - stores parameters in EEPROM
@ -476,10 +574,13 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
//#define DOGLCD // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family)
//#define SDSUPPORT // Enable SD Card Support in Hardware Console
//#define SDSLOW // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error)
//#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication
//#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder
//#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking
//#define ULTIMAKERCONTROLLER //as available from the Ultimaker online store.
//#define ULTIPANEL //the UltiPanel as on Thingiverse
//#define LCD_FEEDBACK_FREQUENCY_HZ 1000 // this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click
//#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 // the duration the buzzer plays the UI feedback sound. ie Screen Click
// The MaKr3d Makr-Panel with graphic controller and SD support
// http://reprap.org/wiki/MaKr3d_MaKrPanel
@ -565,6 +666,21 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
#define LCD_USE_I2C_BUZZER //comment out to disable buzzer on LCD
#define NEWPANEL
#define ULTIPANEL
#ifndef ENCODER_PULSES_PER_STEP
#define ENCODER_PULSES_PER_STEP 4
#endif
#ifndef ENCODER_STEPS_PER_MENU_ITEM
#define ENCODER_STEPS_PER_MENU_ITEM 1
#endif
#ifdef LCD_USE_I2C_BUZZER
#define LCD_FEEDBACK_FREQUENCY_HZ 1000
#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100
#endif
#endif
// Panucatt VIKI LCD with status LEDs, integrated click & L/R/U/P buttons, separate encoder inputs
@ -587,7 +703,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
// https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/schematics#!shiftregister-connection
//#define SR_LCD
#ifdef SR_LCD
#define SR_LCD_2W_NL // Non latching 2 wire shiftregister
#define SR_LCD_2W_NL // Non latching 2 wire shift register
//#define NEWPANEL
#endif
@ -676,6 +792,35 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
//#define SERVO_ENDSTOPS {-1, -1, 0} // Servo index for X, Y, Z. Disable with -1
//#define SERVO_ENDSTOP_ANGLES {0,0, 0,0, 70,0} // X,Y,Z Axis Extend and Retract angles
/**********************************************************************\
* Support for a filament diameter sensor
* Also allows adjustment of diameter at print time (vs at slicing)
* Single extruder only at this point (extruder 0)
*
* Motherboards
* 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector
* 81 - Printrboard - Uses Analog input 2 on the Aux 2 connector
* 301 - Rambo - uses Analog input 3
* Note may require analog pins to be defined for different motherboards
**********************************************************************/
#define FILAMENT_SENSOR
#define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2)
#define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel
#define DEFAULT_NOMINAL_FILAMENT_DIA 3.0 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation
#define MEASURED_UPPER_LIMIT 3.30 //upper limit factor used for sensor reading validation in mm
#define MEASURED_LOWER_LIMIT 1.90 //lower limit factor for sensor reading validation in mm
#define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM)
//defines used in the code
#define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially
#include "Configuration_adv.h"
#include "thermistortables.h"

15
Marlin/example_configurations/delta/Configuration_adv.h

@ -281,6 +281,9 @@
//=============================Additional Features===========================
//===========================================================================
//#define CHDK 4 //Pin for triggering CHDK to take a picture see how to use it here http://captain-slow.dk/2014/03/09/3d-printing-timelapses/
#define CHDK_DELAY 50 //How long in ms the pin should stay HIGH before going LOW again
#define SD_FINISHED_STEPPERRELEASE true //if sd support and the file is finished: disable steppers?
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
@ -401,8 +404,16 @@ const unsigned int dropsegments=5; //everything with less than this number of st
// the moves are than replaced by the firmware controlled ones.
// #define FWRETRACT //ONLY PARTIALLY TESTED
#define MIN_RETRACT 0.1 //minimum extruded mm to accept a automatic gcode retraction attempt
#ifdef FWRETRACT
#define MIN_RETRACT 0.1 //minimum extruded mm to accept a automatic gcode retraction attempt
#define RETRACT_LENGTH 3 //default retract length (positive mm)
#define RETRACT_LENGTH_SWAP 13 //default swap retract length (positive mm), for extruder change
#define RETRACT_FEEDRATE 45 //default feedrate for retracting (mm/s)
#define RETRACT_ZLIFT 0 //default retract Z-lift
#define RETRACT_RECOVER_LENGTH 0 //default additional recover length (mm, added to retract length when recovering)
#define RETRACT_RECOVER_LENGTH_SWAP 0 //default additional swap recover length (mm, added to retract length when recovering from extruder change)
#define RETRACT_RECOVER_FEEDRATE 8 //default feedrate for recovering from retraction (mm/s)
#endif
//adds support for experimental filament exchange support M600; requires display
#ifdef ULTIPANEL

16
Marlin/language.h

@ -665,7 +665,7 @@
#define MSG_AUTOSTART " Autostart"
#define MSG_DISABLE_STEPPERS "Apagar motores"
#define MSG_AUTO_HOME "Llevar al origen"
#define MSG_SET_HOME_OFFSETS "Set home offsets"
#define MSG_SET_HOME_OFFSETS "Ajustar offsets"
#define MSG_SET_ORIGIN "Establecer cero"
#define MSG_PREHEAT_PLA "Precalentar PLA"
#define MSG_PREHEAT_PLA0 "Precalentar PLA 1"
@ -682,8 +682,8 @@
#define MSG_PREHEAT_ABS_BEDONLY "Precal. ABS Base"
#define MSG_PREHEAT_ABS_SETTINGS "Ajustar temp. ABS"
#define MSG_COOLDOWN "Enfriar"
#define MSG_SWITCH_PS_ON "Switch Power On"
#define MSG_SWITCH_PS_OFF "Switch Power Off"
#define MSG_SWITCH_PS_ON "Encender"
#define MSG_SWITCH_PS_OFF "Apagar"
#define MSG_EXTRUDE "Extruir"
#define MSG_RETRACT "Retraer"
#define MSG_MOVE_AXIS "Mover ejes"
@ -727,7 +727,7 @@
#define MSG_Z "z"
#define MSG_E "e"
#define MSG_VMIN "Vmin"
#define MSG_VTRAV_MIN "VTrav min"
#define MSG_VTRAV_MIN "Vvacio min"
#define MSG_AMAX "Amax"
#define MSG_A_RETRACT "A-retrac."
#define MSG_XSTEPS "X pasos/mm"
@ -775,14 +775,14 @@
#define MSG_CONTROL_ARROW "Control"
#define MSG_RETRACT_ARROW "Retraer"
#define MSG_STEPPER_RELEASED "Desacoplada."
#define MSG_ZPROBE_OUT "Z probe out. bed"
#define MSG_POSITION_UNKNOWN "Home X/Y before Z"
#define MSG_ZPROBE_ZOFFSET "Z Offset"
#define MSG_ZPROBE_OUT "sonda Z fuera"
#define MSG_POSITION_UNKNOWN "Reiniciar X/Y y Z"
#define MSG_ZPROBE_ZOFFSET "Offset Z"
#define MSG_BABYSTEP_X "Babystep X"
#define MSG_BABYSTEP_Y "Babystep Y"
#define MSG_BABYSTEP_Z "Babystep Z"
#define MSG_ENDSTOP_ABORT "Endstop abort"
#define MSG_CONTRAST "Contrast"
#define MSG_CONTRAST "Contraste"
#endif

53
Marlin/stepper.cpp

@ -559,6 +559,58 @@ ISR(TIMER1_COMPA_vect)
#endif //ADVANCE
counter_x += current_block->steps_x;
#ifdef CONFIG_STEPPERS_TOSHIBA
/* The toshiba stepper controller require much longer pulses
* tjerfore we 'stage' decompose the pulses between high, and
* low instead of doing each in turn. The extra tests add enough
* lag to allow it work with without needing NOPs */
if (counter_x > 0) {
WRITE(X_STEP_PIN, HIGH);
}
counter_y += current_block->steps_y;
if (counter_y > 0) {
WRITE(Y_STEP_PIN, HIGH);
}
counter_z += current_block->steps_z;
if (counter_z > 0) {
WRITE(Z_STEP_PIN, HIGH);
}
#ifndef ADVANCE
counter_e += current_block->steps_e;
if (counter_e > 0) {
WRITE_E_STEP(HIGH);
}
#endif //!ADVANCE
if (counter_x > 0) {
counter_x -= current_block->step_event_count;
count_position[X_AXIS]+=count_direction[X_AXIS];
WRITE(X_STEP_PIN, LOW);
}
if (counter_y > 0) {
counter_y -= current_block->step_event_count;
count_position[Y_AXIS]+=count_direction[Y_AXIS];
WRITE(Y_STEP_PIN, LOW);
}
if (counter_z > 0) {
counter_z -= current_block->step_event_count;
count_position[Z_AXIS]+=count_direction[Z_AXIS];
WRITE(Z_STEP_PIN, LOW);
}
#ifndef ADVANCE
if (counter_e > 0) {
counter_e -= current_block->step_event_count;
count_position[E_AXIS]+=count_direction[E_AXIS];
WRITE_E_STEP(LOW);
}
#endif //!ADVANCE
#else
if (counter_x > 0) {
#ifdef DUAL_X_CARRIAGE
if (extruder_duplication_enabled){
@ -635,6 +687,7 @@ ISR(TIMER1_COMPA_vect)
WRITE_E_STEP(INVERT_E_STEP_PIN);
}
#endif //!ADVANCE
#endif
step_events_completed += 1;
if(step_events_completed >= current_block->step_event_count) break;
}

29
Marlin/ultralcd.cpp

@ -162,6 +162,8 @@ bool lcd_oldcardstatus;
menuFunc_t currentMenu = lcd_status_screen; /* function pointer to the currently active menu */
uint32_t lcd_next_update_millis;
uint8_t lcd_status_update_delay;
bool ignore_click = false;
bool wait_for_unclick;
uint8_t lcdDrawUpdate = 2; /* Set to none-zero when the LCD needs to draw, decreased after every draw. Set to 2 in LCD routines so the LCD gets at least 1 full redraw (first redraw is partial) */
//prevMenu and prevEncoderPosition are used to store the previous menu location when editing settings.
@ -189,7 +191,26 @@ static void lcd_status_screen()
lcd_status_update_delay = 10; /* redraw the main screen every second. This is easier then trying keep track of all things that change on the screen */
}
#ifdef ULTIPANEL
if (LCD_CLICKED)
bool current_click = LCD_CLICKED;
if (ignore_click) {
if (wait_for_unclick) {
if (!current_click) {
ignore_click = wait_for_unclick = false;
}
else {
current_click = false;
}
}
else if (current_click) {
lcd_quick_feedback();
wait_for_unclick = true;
current_click = false;
}
}
if (current_click)
{
currentMenu = lcd_main_menu;
encoderPosition = 0;
@ -1315,6 +1336,12 @@ void lcd_update()
}
}
void lcd_ignore_click(bool b)
{
ignore_click = b;
wait_for_unclick = false;
}
void lcd_setstatus(const char* message)
{
if (lcd_status_message_level > 0)

2
Marlin/ultralcd.h

@ -49,6 +49,8 @@
void lcd_buzz(long duration,uint16_t freq);
bool lcd_clicked();
void lcd_ignore_click(bool b=true);
#ifdef NEWPANEL
#define EN_C (1<<BLEN_C)
#define EN_B (1<<BLEN_B)

1
README.md

@ -2,6 +2,7 @@
Marlin 3D Printer Firmware
==========================
[![Coverity Scan Build Status](https://scan.coverity.com/projects/2224/badge.svg)](https://scan.coverity.com/projects/2224)
[![Travis Build Status](https://travis-ci.org/ErikZalm/Marlin.svg)](https://travis-ci.org/ErikZalm/Marlin)
Marlin has a GPL license because I believe in open development.
Please do not use this code in products (3D printers, CNC etc) that are closed source or are crippled by a patent.

Loading…
Cancel
Save