BIBO2 default update and Cyclops config (#10108)

Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration.h

@@ -315,7 +315,7 @@
 #define TEMP_SENSOR_2 0
 #define TEMP_SENSOR_3 0
 #define TEMP_SENSOR_4 0
-#define TEMP_SENSOR_BED 60
+#define TEMP_SENSOR_BED 5
 
 // Dummy thermistor constant temperature readings, for use with 998 and 999
 #define DUMMY_THERMISTOR_998_VALUE 25
@@ -442,8 +442,8 @@
 // It also enables the M302 command to set the minimum extrusion temperature
 // or to allow moving the extruder regardless of the hotend temperature.
 // *** IT IS HIGHLY RECOMMENDED TO LEAVE THIS OPTION ENABLED! ***
-#define PREVENT_COLD_EXTRUSION
+//#define PREVENT_COLD_EXTRUSION
-#define EXTRUDE_MINTEMP 170
+//#define EXTRUDE_MINTEMP 170
 
 // This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH.
 // Note that for Bowden Extruders a too-small value here may prevent loading.
@@ -494,11 +494,11 @@
 // Specify here all the endstop connectors that are connected to any endstop or probe.
 // Almost all printers will be using one per axis. Probes will use one or more of the
 // extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
-//#define USE_XMIN_PLUG
+#define USE_XMIN_PLUG
-//#define USE_YMIN_PLUG
+#define USE_YMIN_PLUG
 #define USE_ZMIN_PLUG
-#define USE_XMAX_PLUG
+//#define USE_XMAX_PLUG
-#define USE_YMAX_PLUG
+//#define USE_YMAX_PLUG
 //#define USE_ZMAX_PLUG
 
 // Enable pullup for all endstops to prevent a floating state
@@ -565,14 +565,14 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
  * Override with M92
  *                                      X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
  */
-#define DEFAULT_AXIS_STEPS_PER_UNIT   { 100, 100, 400, 93.6 }
+#define DEFAULT_AXIS_STEPS_PER_UNIT   { 100, 100, 400, 400 }
 
 /**
  * Default Max Feed Rate (mm/s)
  * Override with M203
  *                                      X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
  */
-#define DEFAULT_MAX_FEEDRATE          { 350, 350, 10, 25 }
+#define DEFAULT_MAX_FEEDRATE          { 350, 350, 10, 50 }
 
 /**
  * Default Max Acceleration (change/s) change = mm/s
@@ -580,7 +580,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
  * Override with M201
  *                                      X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
  */
-#define DEFAULT_MAX_ACCELERATION      { 1100, 1100, 300, 5000 }
+#define DEFAULT_MAX_ACCELERATION      { 1100, 1100, 300, 2500 }
 
 /**
  * Default Acceleration (change/s) change = mm/s
@@ -727,7 +727,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 #define MIN_PROBE_EDGE 10
 
 // X and Y axis travel speed (mm/m) between probes
-#define XY_PROBE_SPEED 8000
+#define XY_PROBE_SPEED 9000
 
 // Speed for the first approach when double-probing (MULTIPLE_PROBING == 2)
 #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
@@ -755,7 +755,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
  *     But: `M851 Z+1` with a CLEARANCE of 2  =>  2mm from bed to nozzle.
  */
 #define Z_CLEARANCE_DEPLOY_PROBE   10 // Z Clearance for Deploy/Stow
-#define Z_CLEARANCE_BETWEEN_PROBES 10 // Z Clearance between probe points
+#define Z_CLEARANCE_BETWEEN_PROBES  5 // Z Clearance between probe points
 //#define Z_AFTER_PROBING          10 // Z position after probing is done
 
 // For M851 give a range for adjusting the Z probe offset
@@ -788,8 +788,8 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 // @section machine
 
 // Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
-#define INVERT_X_DIR false
+#define INVERT_X_DIR true
-#define INVERT_Y_DIR true
+#define INVERT_Y_DIR false
 #define INVERT_Z_DIR false
 
 // Enable this option for Toshiba stepper drivers
@@ -815,22 +815,22 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
-#define X_HOME_DIR 1
+#define X_HOME_DIR -1
-#define Y_HOME_DIR 1
+#define Y_HOME_DIR -1
 #define Z_HOME_DIR -1
 
 // @section machine
 
 // The size of the print bed
-#define X_BED_SIZE 214
+#define X_BED_SIZE 220
 #define Y_BED_SIZE 186
 
 // Travel limits (mm) after homing, corresponding to endstop positions.
-#define X_MIN_POS -107
+#define X_MIN_POS -13
-#define Y_MIN_POS -93
+#define Y_MIN_POS 0
 #define Z_MIN_POS 0
-#define X_MAX_POS 141
+#define X_MAX_POS 250
-#define Y_MAX_POS 93
+#define Y_MAX_POS 186
 #define Z_MAX_POS 186
 
 /**
@@ -1090,8 +1090,8 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 #endif
 
 // Homing speeds (mm/m)
-#define HOMING_FEEDRATE_XY (15*60)
+#define HOMING_FEEDRATE_XY (25*60)
-#define HOMING_FEEDRATE_Z  (4*60)
+#define HOMING_FEEDRATE_Z  (6*60)
 
 // @section calibrate
 
@@ -1196,12 +1196,12 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 // @section temperature
 
 // Preheat Constants
-#define PREHEAT_1_TEMP_HOTEND 180
+#define PREHEAT_1_TEMP_HOTEND 190
-#define PREHEAT_1_TEMP_BED     60
+#define PREHEAT_1_TEMP_BED     65
 #define PREHEAT_1_FAN_SPEED     0 // Value from 0 to 255
 
 #define PREHEAT_2_TEMP_HOTEND 240
-#define PREHEAT_2_TEMP_BED    80
+#define PREHEAT_2_TEMP_BED    100
 #define PREHEAT_2_FAN_SPEED     0 // Value from 0 to 255
 
 /**