Browse Source

Cosmetic patches

pull/1/head
Scott Lahteine 8 years ago
parent
commit
5bdb0b567d
  1. 16
      Marlin/Marlin_main.cpp
  2. 3
      Marlin/printcounter.cpp
  3. 4
      Marlin/printcounter.h
  4. 6
      Marlin/temperature.cpp
  5. 2
      Marlin/ultralcd.cpp

16
Marlin/Marlin_main.cpp

@ -616,12 +616,12 @@ static uint8_t target_extruder;
float cartes[XYZ] = { 0 };
#if ENABLED(FILAMENT_WIDTH_SENSOR)
bool filament_sensor = false; //M405 turns on filament_sensor control, M406 turns it off
float filament_width_nominal = DEFAULT_NOMINAL_FILAMENT_DIA, // Nominal filament width. Change with M404
bool filament_sensor = false; // M405 turns on filament sensor control. M406 turns it off.
float filament_width_nominal = DEFAULT_NOMINAL_FILAMENT_DIA, // Nominal filament width. Change with M404.
filament_width_meas = DEFAULT_MEASURED_FILAMENT_DIA; // Measured filament diameter
int8_t measurement_delay[MAX_MEASUREMENT_DELAY + 1]; // Ring buffer to delayed measurement. Store extruder factor after subtracting 100
int filwidth_delay_index[2] = { 0, -1 }; // Indexes into ring buffer
int meas_delay_cm = MEASUREMENT_DELAY_CM; //distance delay setting
int8_t measurement_delay[MAX_MEASUREMENT_DELAY + 1]; // Ring buffer to delayed measurement. Store extruder factor after subtracting 100
int filwidth_delay_index[2] = { 0, -1 }; // Indexes into ring buffer
int meas_delay_cm = MEASUREMENT_DELAY_CM; // Distance delay setting
#endif
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
@ -8220,10 +8220,10 @@ inline void gcode_M400() { stepper.synchronize(); }
NOMORE(meas_delay_cm, MAX_MEASUREMENT_DELAY);
if (filwidth_delay_index[1] == -1) { // Initialize the ring buffer if not done since startup
int temp_ratio = thermalManager.widthFil_to_size_ratio();
const int temp_ratio = thermalManager.widthFil_to_size_ratio() - 100; // -100 to scale within a signed byte
for (uint8_t i = 0; i < COUNT(measurement_delay); ++i)
measurement_delay[i] = temp_ratio - 100; // Subtract 100 to scale within a signed byte
measurement_delay[i] = temp_ratio;
filwidth_delay_index[0] = filwidth_delay_index[1] = 0;
}
@ -10279,7 +10279,7 @@ void process_next_command() {
case 407: // M407: Display measured filament diameter
gcode_M407();
break;
#endif // ENABLED(FILAMENT_WIDTH_SENSOR)
#endif // FILAMENT_WIDTH_SENSOR
#if PLANNER_LEVELING
case 420: // M420: Enable/Disable Bed Leveling

3
Marlin/printcounter.cpp

@ -188,7 +188,8 @@ bool PrintCounter::start() {
}
return true;
}
else return false;
return false;
}
// @Override

4
Marlin/printcounter.h

@ -32,12 +32,12 @@
// Print debug messages with M111 S2
//#define DEBUG_PRINTCOUNTER
struct printStatistics { // 13 bytes
struct printStatistics { // 16 bytes (20 with real doubles)
//const uint8_t magic; // Magic header, it will always be 0x16
uint16_t totalPrints; // Number of prints
uint16_t finishedPrints; // Number of complete prints
uint32_t printTime; // Accumulated printing time
uint32_t longestPrint; // Longest successfull print job
uint32_t longestPrint; // Longest successful print job
double filamentUsed; // Accumulated filament consumed in mm
};

6
Marlin/temperature.cpp

@ -774,7 +774,7 @@ void Temperature::manage_heater() {
NOLESS(vm, 0.01);
volumetric_multiplier[FILAMENT_SENSOR_EXTRUDER_NUM] = vm;
}
#endif //FILAMENT_WIDTH_SENSOR
#endif // FILAMENT_WIDTH_SENSOR
#if DISABLED(PIDTEMPBED)
if (PENDING(ms, next_bed_check_ms)) return;
@ -961,8 +961,8 @@ void Temperature::updateTemperaturesFromRawValues() {
*/
void Temperature::init() {
#if MB(RUMBA) && ((TEMP_SENSOR_0==-1)||(TEMP_SENSOR_1==-1)||(TEMP_SENSOR_2==-1)||(TEMP_SENSOR_BED==-1))
//disable RUMBA JTAG in case the thermocouple extension is plugged on top of JTAG connector
#if MB(RUMBA) && (TEMP_SENSOR_0 == -1 || TEMP_SENSOR_1 == -1 || TEMP_SENSOR_2 == -1 || TEMP_SENSOR_BED == -1)
// Disable RUMBA JTAG in case the thermocouple extension is plugged on top of JTAG connector
MCUCR = _BV(JTD);
MCUCR = _BV(JTD);
#endif

2
Marlin/ultralcd.cpp

@ -2725,7 +2725,7 @@ void kill_screen(const char* lcd_msg) {
START_SCREEN(); // 12345678901234567890
STATIC_ITEM(MSG_INFO_PRINT_COUNT ": ", false, false, itostr3left(stats.totalPrints)); // Print Count: 999
STATIC_ITEM(MSG_INFO_COMPLETED_PRINTS": ", false, false, itostr3left(stats.finishedPrints)); // Completed : 666
STATIC_ITEM(MSG_INFO_COMPLETED_PRINTS": ", false, false, itostr3left(stats.finishedPrints)); // Completed : 666
duration_t elapsed = stats.printTime;
elapsed.toString(buffer);

Loading…
Cancel
Save