diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h
index a91fa086a5..16d0bfa317 100644
--- a/Marlin/Configuration.h
+++ b/Marlin/Configuration.h
@@ -818,7 +818,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/Marlin/src/feature/bltouch.cpp b/Marlin/src/feature/bltouch.cpp
index fdbab975e9..2e68835f39 100644
--- a/Marlin/src/feature/bltouch.cpp
+++ b/Marlin/src/feature/bltouch.cpp
@@ -70,19 +70,21 @@ bool BLTouch::set_deployed(const bool in_deploy) {
     }
   }
 
-  #if ENABLED(BLTOUCH_FORCE_5V_MODE)
-    set_5V_mode();
-  #elif ENABLED(BLTOUCH_FORCE_OPEN_DRAIN_MODE)
-    set_OD_mode();
-  #elif ENABLED(ENDSTOPPULLUPS) || ALL(Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN, ENDSTOPPULLUP_ZMIN) || (USES_Z_MIN_PROBE_ENDSTOP && ENABLED(ENDSTOPPULLUP_ZMIN_PROBE))
-    set_5V_mode();                  // Assume 5V DC logic level if endstop pullup resistors are enabled
-  #else
-    set_OD_mode();
+  #if ENABLED(BLTOUCH_V3)
+    #if  EITHER(BLTOUCH_FORCE_5V_MODE, ENDSTOPPULLUPS) \
+      || ALL(Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN, ENDSTOPPULLUP_ZMIN) \
+      || (USES_Z_MIN_PROBE_ENDSTOP && ENABLED(ENDSTOPPULLUP_ZMIN_PROBE))
+      set_5V_mode();  // Assume 5V DC logic level if endstop pullup resistors are enabled
+    #elif true || ENABLED(BLTOUCH_FORCE_OPEN_DRAIN_MODE)
+      set_OD_mode();
+    #endif
   #endif
 
   if (in_deploy) {
     _deploy();
-    set_SW_mode();                  // Ensure Switch mode is activated for BLTouch V3. Ignored on V2.
+    #if ENABLED(BLTOUCH_V3)
+      set_SW_mode();
+    #endif
   }
   else _stow();
 
diff --git a/Marlin/src/feature/bltouch.h b/Marlin/src/feature/bltouch.h
index 09fe1d7997..553caa60ad 100644
--- a/Marlin/src/feature/bltouch.h
+++ b/Marlin/src/feature/bltouch.h
@@ -43,21 +43,9 @@ public:
   FORCE_INLINE static void reset()       { command(BLTOUCH_RESET); }
   FORCE_INLINE static void selftest()    { command(BLTOUCH_SELFTEST); }
 
-  FORCE_INLINE static void set_5V_mode() { 
-    #if ENABLED(BLTOUCH_V3)
-      command(BLTOUCH_5V_MODE);
-    #endif
-  }
-  FORCE_INLINE static void set_OD_mode() {
-    #if ENABLED(BLTOUCH_V3)
-      command(BLTOUCH_OD_MODE);
-    #endif
-  }
-  FORCE_INLINE static void set_SW_mode() {
-    #if ENABLED(BLTOUCH_V3)
-      command(BLTOUCH_SW_MODE);
-    #endif
-  }
+  FORCE_INLINE static void set_5V_mode() { command(BLTOUCH_5V_MODE); }
+  FORCE_INLINE static void set_OD_mode() { command(BLTOUCH_OD_MODE); }
+  FORCE_INLINE static void set_SW_mode() { command(BLTOUCH_SW_MODE); }
 
   FORCE_INLINE static bool deploy()      { return set_deployed(true); }
   FORCE_INLINE static bool stow()        { return set_deployed(false); }
diff --git a/config/default/Configuration.h b/config/default/Configuration.h
index a91fa086a5..16d0bfa317 100644
--- a/config/default/Configuration.h
+++ b/config/default/Configuration.h
@@ -818,7 +818,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/3DFabXYZ/Migbot/Configuration.h b/config/examples/3DFabXYZ/Migbot/Configuration.h
index 15560cf382..2a7bf9b8d2 100644
--- a/config/examples/3DFabXYZ/Migbot/Configuration.h
+++ b/config/examples/3DFabXYZ/Migbot/Configuration.h
@@ -824,7 +824,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/AlephObjects/TAZ4/Configuration.h b/config/examples/AlephObjects/TAZ4/Configuration.h
index 3747d9a31a..7db2f6399c 100644
--- a/config/examples/AlephObjects/TAZ4/Configuration.h
+++ b/config/examples/AlephObjects/TAZ4/Configuration.h
@@ -838,7 +838,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/AliExpress/CL-260/Configuration.h b/config/examples/AliExpress/CL-260/Configuration.h
index 3e3accbc15..60c7948169 100644
--- a/config/examples/AliExpress/CL-260/Configuration.h
+++ b/config/examples/AliExpress/CL-260/Configuration.h
@@ -818,7 +818,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/AliExpress/UM2pExt/Configuration.h b/config/examples/AliExpress/UM2pExt/Configuration.h
index 676995a42b..96f7ba5bd3 100644
--- a/config/examples/AliExpress/UM2pExt/Configuration.h
+++ b/config/examples/AliExpress/UM2pExt/Configuration.h
@@ -829,7 +829,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/Anet/A2/Configuration.h b/config/examples/Anet/A2/Configuration.h
index 94613dde50..7f5c349429 100644
--- a/config/examples/Anet/A2/Configuration.h
+++ b/config/examples/Anet/A2/Configuration.h
@@ -818,7 +818,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/Anet/A2plus/Configuration.h b/config/examples/Anet/A2plus/Configuration.h
index 09798c0db8..1349858378 100644
--- a/config/examples/Anet/A2plus/Configuration.h
+++ b/config/examples/Anet/A2plus/Configuration.h
@@ -818,7 +818,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/Anet/A6/Configuration.h b/config/examples/Anet/A6/Configuration.h
index 15714b3d8e..81569f6177 100644
--- a/config/examples/Anet/A6/Configuration.h
+++ b/config/examples/Anet/A6/Configuration.h
@@ -865,7 +865,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/Anet/A8/Configuration.h b/config/examples/Anet/A8/Configuration.h
index eeb8b33eb6..47b828ce4c 100644
--- a/config/examples/Anet/A8/Configuration.h
+++ b/config/examples/Anet/A8/Configuration.h
@@ -831,7 +831,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/AnyCubic/i3/Configuration.h b/config/examples/AnyCubic/i3/Configuration.h
index 8bd1e9a78e..d4c6e0e01c 100644
--- a/config/examples/AnyCubic/i3/Configuration.h
+++ b/config/examples/AnyCubic/i3/Configuration.h
@@ -828,7 +828,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/ArmEd/Configuration.h b/config/examples/ArmEd/Configuration.h
index 5489374210..70c54296f3 100644
--- a/config/examples/ArmEd/Configuration.h
+++ b/config/examples/ArmEd/Configuration.h
@@ -819,7 +819,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/Azteeg/X5GT/Configuration.h b/config/examples/Azteeg/X5GT/Configuration.h
index acf3640be8..fc93873ed5 100644
--- a/config/examples/Azteeg/X5GT/Configuration.h
+++ b/config/examples/Azteeg/X5GT/Configuration.h
@@ -818,7 +818,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/BIBO/TouchX/cyclops/Configuration.h b/config/examples/BIBO/TouchX/cyclops/Configuration.h
index 4e76fd0bbc..b44d388496 100644
--- a/config/examples/BIBO/TouchX/cyclops/Configuration.h
+++ b/config/examples/BIBO/TouchX/cyclops/Configuration.h
@@ -818,7 +818,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/BIBO/TouchX/default/Configuration.h b/config/examples/BIBO/TouchX/default/Configuration.h
index 5ee4df2ba0..d338ca8a52 100644
--- a/config/examples/BIBO/TouchX/default/Configuration.h
+++ b/config/examples/BIBO/TouchX/default/Configuration.h
@@ -818,7 +818,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/BQ/Hephestos/Configuration.h b/config/examples/BQ/Hephestos/Configuration.h
index c8d4527d7b..f75ed2fcf6 100644
--- a/config/examples/BQ/Hephestos/Configuration.h
+++ b/config/examples/BQ/Hephestos/Configuration.h
@@ -806,7 +806,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/BQ/Hephestos_2/Configuration.h b/config/examples/BQ/Hephestos_2/Configuration.h
index e4793603c6..2f2594e99a 100644
--- a/config/examples/BQ/Hephestos_2/Configuration.h
+++ b/config/examples/BQ/Hephestos_2/Configuration.h
@@ -819,7 +819,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/BQ/WITBOX/Configuration.h b/config/examples/BQ/WITBOX/Configuration.h
index b531fd831d..c89413b5c5 100644
--- a/config/examples/BQ/WITBOX/Configuration.h
+++ b/config/examples/BQ/WITBOX/Configuration.h
@@ -806,7 +806,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/Cartesio/Configuration.h b/config/examples/Cartesio/Configuration.h
index f89b482b21..74fa02b18b 100644
--- a/config/examples/Cartesio/Configuration.h
+++ b/config/examples/Cartesio/Configuration.h
@@ -817,7 +817,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/Creality/CR-10/Configuration.h b/config/examples/Creality/CR-10/Configuration.h
index c6b960a4ed..0b881bcde7 100644
--- a/config/examples/Creality/CR-10/Configuration.h
+++ b/config/examples/Creality/CR-10/Configuration.h
@@ -828,7 +828,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/Creality/CR-10S/Configuration.h b/config/examples/Creality/CR-10S/Configuration.h
index 22a3827211..b372077e92 100644
--- a/config/examples/Creality/CR-10S/Configuration.h
+++ b/config/examples/Creality/CR-10S/Configuration.h
@@ -818,7 +818,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/Creality/CR-10_5S/Configuration.h b/config/examples/Creality/CR-10_5S/Configuration.h
index 6e6e664b30..17d0f49d8a 100644
--- a/config/examples/Creality/CR-10_5S/Configuration.h
+++ b/config/examples/Creality/CR-10_5S/Configuration.h
@@ -819,7 +819,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/Creality/CR-10mini/Configuration.h b/config/examples/Creality/CR-10mini/Configuration.h
index 3035e06026..ee693f30b9 100644
--- a/config/examples/Creality/CR-10mini/Configuration.h
+++ b/config/examples/Creality/CR-10mini/Configuration.h
@@ -837,7 +837,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/Creality/CR-8/Configuration.h b/config/examples/Creality/CR-8/Configuration.h
index d03b46d3b2..6285715af9 100644
--- a/config/examples/Creality/CR-8/Configuration.h
+++ b/config/examples/Creality/CR-8/Configuration.h
@@ -828,7 +828,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/Creality/Ender-2/Configuration.h b/config/examples/Creality/Ender-2/Configuration.h
index 606f77029e..8e07221354 100644
--- a/config/examples/Creality/Ender-2/Configuration.h
+++ b/config/examples/Creality/Ender-2/Configuration.h
@@ -822,7 +822,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/Creality/Ender-3/Configuration.h b/config/examples/Creality/Ender-3/Configuration.h
index 902195826a..ebf1455c9d 100644
--- a/config/examples/Creality/Ender-3/Configuration.h
+++ b/config/examples/Creality/Ender-3/Configuration.h
@@ -822,7 +822,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/Creality/Ender-4/Configuration.h b/config/examples/Creality/Ender-4/Configuration.h
index d03a00d560..af5f71e93a 100644
--- a/config/examples/Creality/Ender-4/Configuration.h
+++ b/config/examples/Creality/Ender-4/Configuration.h
@@ -828,7 +828,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/Einstart-S/Configuration.h b/config/examples/Einstart-S/Configuration.h
index cc90be6b23..fd1a179761 100644
--- a/config/examples/Einstart-S/Configuration.h
+++ b/config/examples/Einstart-S/Configuration.h
@@ -829,7 +829,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/Felix/Configuration.h b/config/examples/Felix/Configuration.h
index 0df79fa71c..3d951698f8 100644
--- a/config/examples/Felix/Configuration.h
+++ b/config/examples/Felix/Configuration.h
@@ -800,7 +800,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/Felix/DUAL/Configuration.h b/config/examples/Felix/DUAL/Configuration.h
index 750355cab7..841da015db 100644
--- a/config/examples/Felix/DUAL/Configuration.h
+++ b/config/examples/Felix/DUAL/Configuration.h
@@ -800,7 +800,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/FlashForge/CreatorPro/Configuration.h b/config/examples/FlashForge/CreatorPro/Configuration.h
index db76df8898..a267439e7b 100644
--- a/config/examples/FlashForge/CreatorPro/Configuration.h
+++ b/config/examples/FlashForge/CreatorPro/Configuration.h
@@ -810,7 +810,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/FolgerTech/i3-2020/Configuration.h b/config/examples/FolgerTech/i3-2020/Configuration.h
index 148660c7ac..ec04f97539 100644
--- a/config/examples/FolgerTech/i3-2020/Configuration.h
+++ b/config/examples/FolgerTech/i3-2020/Configuration.h
@@ -824,7 +824,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/Formbot/Raptor/Configuration.h b/config/examples/Formbot/Raptor/Configuration.h
index 48aa28b6df..a127789604 100644
--- a/config/examples/Formbot/Raptor/Configuration.h
+++ b/config/examples/Formbot/Raptor/Configuration.h
@@ -901,7 +901,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/Formbot/T_Rex_2+/Configuration.h b/config/examples/Formbot/T_Rex_2+/Configuration.h
index bfefe362d6..451e352560 100644
--- a/config/examples/Formbot/T_Rex_2+/Configuration.h
+++ b/config/examples/Formbot/T_Rex_2+/Configuration.h
@@ -847,7 +847,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/Formbot/T_Rex_3/Configuration.h b/config/examples/Formbot/T_Rex_3/Configuration.h
index bcdbd6cb1c..6935056e8e 100644
--- a/config/examples/Formbot/T_Rex_3/Configuration.h
+++ b/config/examples/Formbot/T_Rex_3/Configuration.h
@@ -834,7 +834,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/Geeetech/A10M/Configuration.h b/config/examples/Geeetech/A10M/Configuration.h
index fa7d499af5..f8be81c5e4 100644
--- a/config/examples/Geeetech/A10M/Configuration.h
+++ b/config/examples/Geeetech/A10M/Configuration.h
@@ -801,7 +801,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/Geeetech/A20M/Configuration.h b/config/examples/Geeetech/A20M/Configuration.h
index 2cfaddbe6e..8d52093c09 100644
--- a/config/examples/Geeetech/A20M/Configuration.h
+++ b/config/examples/Geeetech/A20M/Configuration.h
@@ -801,7 +801,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/Geeetech/GT2560/Configuration.h b/config/examples/Geeetech/GT2560/Configuration.h
index c69ca7ba17..d5c52b694c 100644
--- a/config/examples/Geeetech/GT2560/Configuration.h
+++ b/config/examples/Geeetech/GT2560/Configuration.h
@@ -833,7 +833,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/Geeetech/MeCreator2/Configuration.h b/config/examples/Geeetech/MeCreator2/Configuration.h
index 245f5e499b..9a7d4c7048 100644
--- a/config/examples/Geeetech/MeCreator2/Configuration.h
+++ b/config/examples/Geeetech/MeCreator2/Configuration.h
@@ -825,7 +825,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h
index 5c0309902c..ee0e8166d9 100644
--- a/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h	
+++ b/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h	
@@ -834,7 +834,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h
index 7531c5ac3d..12f48870e7 100644
--- a/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h	
+++ b/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h	
@@ -833,7 +833,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h
index a0a4f7dc41..5698c217de 100644
--- a/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h	
+++ b/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h	
@@ -818,7 +818,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h
index 60a66b72af..79ea413150 100644
--- a/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h	
+++ b/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h	
@@ -818,7 +818,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/Infitary/i3-M508/Configuration.h b/config/examples/Infitary/i3-M508/Configuration.h
index a100bc54f5..2d25e6afe7 100644
--- a/config/examples/Infitary/i3-M508/Configuration.h
+++ b/config/examples/Infitary/i3-M508/Configuration.h
@@ -822,7 +822,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/JGAurora/A5/Configuration.h b/config/examples/JGAurora/A5/Configuration.h
index ebf2745adf..686a90d9db 100644
--- a/config/examples/JGAurora/A5/Configuration.h
+++ b/config/examples/JGAurora/A5/Configuration.h
@@ -830,7 +830,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/MakerParts/Configuration.h b/config/examples/MakerParts/Configuration.h
index e5ec46bdb5..ec81d59d02 100644
--- a/config/examples/MakerParts/Configuration.h
+++ b/config/examples/MakerParts/Configuration.h
@@ -838,7 +838,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/Malyan/M150/Configuration.h b/config/examples/Malyan/M150/Configuration.h
index 1e2a6e2884..f4e390a9f5 100644
--- a/config/examples/Malyan/M150/Configuration.h
+++ b/config/examples/Malyan/M150/Configuration.h
@@ -838,7 +838,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/Malyan/M200/Configuration.h b/config/examples/Malyan/M200/Configuration.h
index 5c7e5050dd..7ef45d7370 100644
--- a/config/examples/Malyan/M200/Configuration.h
+++ b/config/examples/Malyan/M200/Configuration.h
@@ -817,7 +817,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/Micromake/C1/basic/Configuration.h b/config/examples/Micromake/C1/basic/Configuration.h
index 79445d7b3f..165c59b6cd 100644
--- a/config/examples/Micromake/C1/basic/Configuration.h
+++ b/config/examples/Micromake/C1/basic/Configuration.h
@@ -822,7 +822,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/Micromake/C1/enhanced/Configuration.h b/config/examples/Micromake/C1/enhanced/Configuration.h
index 89c1e9e753..ebc346557c 100644
--- a/config/examples/Micromake/C1/enhanced/Configuration.h
+++ b/config/examples/Micromake/C1/enhanced/Configuration.h
@@ -822,7 +822,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/Mks/Robin/Configuration.h b/config/examples/Mks/Robin/Configuration.h
index 3691cb9517..badacbb6da 100644
--- a/config/examples/Mks/Robin/Configuration.h
+++ b/config/examples/Mks/Robin/Configuration.h
@@ -819,7 +819,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/Mks/Sbase/Configuration.h b/config/examples/Mks/Sbase/Configuration.h
index f32d6d55fd..18dc3f9d63 100644
--- a/config/examples/Mks/Sbase/Configuration.h
+++ b/config/examples/Mks/Sbase/Configuration.h
@@ -818,7 +818,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/Printrbot/PrintrboardG2/Configuration.h b/config/examples/Printrbot/PrintrboardG2/Configuration.h
index 1830f70952..0c2b1cd67d 100644
--- a/config/examples/Printrbot/PrintrboardG2/Configuration.h
+++ b/config/examples/Printrbot/PrintrboardG2/Configuration.h
@@ -826,7 +826,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/RapideLite/RL200/Configuration.h b/config/examples/RapideLite/RL200/Configuration.h
index f50959e5da..b1940d723f 100644
--- a/config/examples/RapideLite/RL200/Configuration.h
+++ b/config/examples/RapideLite/RL200/Configuration.h
@@ -818,7 +818,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/RepRapPro/Huxley/Configuration.h b/config/examples/RepRapPro/Huxley/Configuration.h
index 6fd123394a..9e8b5c55f4 100644
--- a/config/examples/RepRapPro/Huxley/Configuration.h
+++ b/config/examples/RepRapPro/Huxley/Configuration.h
@@ -858,7 +858,11 @@ Black rubber belt(MXL), 18 - tooth aluminium pulley : 87.489 step per mm (Huxley
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/RepRapWorld/Megatronics/Configuration.h b/config/examples/RepRapWorld/Megatronics/Configuration.h
index 836bcae079..4b6cd06abe 100644
--- a/config/examples/RepRapWorld/Megatronics/Configuration.h
+++ b/config/examples/RepRapWorld/Megatronics/Configuration.h
@@ -818,7 +818,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/RigidBot/Configuration.h b/config/examples/RigidBot/Configuration.h
index 0afc55d7e7..27c9471f75 100644
--- a/config/examples/RigidBot/Configuration.h
+++ b/config/examples/RigidBot/Configuration.h
@@ -816,7 +816,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/SCARA/Configuration.h b/config/examples/SCARA/Configuration.h
index e9612a79b2..8b5284655a 100644
--- a/config/examples/SCARA/Configuration.h
+++ b/config/examples/SCARA/Configuration.h
@@ -831,7 +831,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/STM32F10/Configuration.h b/config/examples/STM32F10/Configuration.h
index 401870642f..da9b22431c 100644
--- a/config/examples/STM32F10/Configuration.h
+++ b/config/examples/STM32F10/Configuration.h
@@ -820,7 +820,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/STM32F4/Configuration.h b/config/examples/STM32F4/Configuration.h
index 1c4aac98bd..8979f40fce 100644
--- a/config/examples/STM32F4/Configuration.h
+++ b/config/examples/STM32F4/Configuration.h
@@ -818,7 +818,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/Sanguinololu/Configuration.h b/config/examples/Sanguinololu/Configuration.h
index a485ee93c6..5382da453c 100644
--- a/config/examples/Sanguinololu/Configuration.h
+++ b/config/examples/Sanguinololu/Configuration.h
@@ -849,7 +849,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/TheBorg/Configuration.h b/config/examples/TheBorg/Configuration.h
index 61491de10f..787d2dad6d 100644
--- a/config/examples/TheBorg/Configuration.h
+++ b/config/examples/TheBorg/Configuration.h
@@ -818,7 +818,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/TinyBoy2/Configuration.h b/config/examples/TinyBoy2/Configuration.h
index 95335fd43f..f4ddd1d5a2 100644
--- a/config/examples/TinyBoy2/Configuration.h
+++ b/config/examples/TinyBoy2/Configuration.h
@@ -869,7 +869,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/Tronxy/X1/Configuration.h b/config/examples/Tronxy/X1/Configuration.h
index 2de1e1881a..22489b6ba4 100644
--- a/config/examples/Tronxy/X1/Configuration.h
+++ b/config/examples/Tronxy/X1/Configuration.h
@@ -818,7 +818,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/Tronxy/X3A/Configuration.h b/config/examples/Tronxy/X3A/Configuration.h
index 569f71b143..c20bac923d 100644
--- a/config/examples/Tronxy/X3A/Configuration.h
+++ b/config/examples/Tronxy/X3A/Configuration.h
@@ -818,7 +818,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/Tronxy/X5S-2E/Configuration.h b/config/examples/Tronxy/X5S-2E/Configuration.h
index 4d199135ba..b57f799750 100644
--- a/config/examples/Tronxy/X5S-2E/Configuration.h
+++ b/config/examples/Tronxy/X5S-2E/Configuration.h
@@ -839,7 +839,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/Tronxy/X5S/Configuration.h b/config/examples/Tronxy/X5S/Configuration.h
index 8bbc418bf6..c93f4d158b 100644
--- a/config/examples/Tronxy/X5S/Configuration.h
+++ b/config/examples/Tronxy/X5S/Configuration.h
@@ -817,7 +817,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/Tronxy/XY100/Configuration.h b/config/examples/Tronxy/XY100/Configuration.h
index 5896ff9017..a68dd5fb62 100644
--- a/config/examples/Tronxy/XY100/Configuration.h
+++ b/config/examples/Tronxy/XY100/Configuration.h
@@ -829,7 +829,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/UltiMachine/Archim1/Configuration.h b/config/examples/UltiMachine/Archim1/Configuration.h
index 640f641bd2..15696b31b2 100644
--- a/config/examples/UltiMachine/Archim1/Configuration.h
+++ b/config/examples/UltiMachine/Archim1/Configuration.h
@@ -818,7 +818,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/UltiMachine/Archim2/Configuration.h b/config/examples/UltiMachine/Archim2/Configuration.h
index 992dc74a1d..8425c5006d 100644
--- a/config/examples/UltiMachine/Archim2/Configuration.h
+++ b/config/examples/UltiMachine/Archim2/Configuration.h
@@ -818,7 +818,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/VORONDesign/Configuration.h b/config/examples/VORONDesign/Configuration.h
index ed88411e4b..422eb1827c 100644
--- a/config/examples/VORONDesign/Configuration.h
+++ b/config/examples/VORONDesign/Configuration.h
@@ -827,7 +827,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/Velleman/K8200/Configuration.h b/config/examples/Velleman/K8200/Configuration.h
index 1a21b57b06..6b7b5cc486 100644
--- a/config/examples/Velleman/K8200/Configuration.h
+++ b/config/examples/Velleman/K8200/Configuration.h
@@ -847,7 +847,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/Velleman/K8400/Configuration.h b/config/examples/Velleman/K8400/Configuration.h
index 5a3579da02..81e6768dee 100644
--- a/config/examples/Velleman/K8400/Configuration.h
+++ b/config/examples/Velleman/K8400/Configuration.h
@@ -818,7 +818,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/Velleman/K8400/Dual-head/Configuration.h b/config/examples/Velleman/K8400/Dual-head/Configuration.h
index af706f2133..d0807339ab 100644
--- a/config/examples/Velleman/K8400/Dual-head/Configuration.h
+++ b/config/examples/Velleman/K8400/Dual-head/Configuration.h
@@ -818,7 +818,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/WASP/PowerWASP/Configuration.h b/config/examples/WASP/PowerWASP/Configuration.h
index 3bd1013e2e..c2b841855b 100644
--- a/config/examples/WASP/PowerWASP/Configuration.h
+++ b/config/examples/WASP/PowerWASP/Configuration.h
@@ -837,7 +837,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/Wanhao/Duplicator 6/Configuration.h b/config/examples/Wanhao/Duplicator 6/Configuration.h
index 3cdf238ba1..e554ec3e39 100644
--- a/config/examples/Wanhao/Duplicator 6/Configuration.h	
+++ b/config/examples/Wanhao/Duplicator 6/Configuration.h	
@@ -828,7 +828,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/adafruit/ST7565/Configuration.h b/config/examples/adafruit/ST7565/Configuration.h
index d010916487..80b8869006 100644
--- a/config/examples/adafruit/ST7565/Configuration.h
+++ b/config/examples/adafruit/ST7565/Configuration.h
@@ -818,7 +818,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/delta/Anycubic/Kossel/Configuration.h b/config/examples/delta/Anycubic/Kossel/Configuration.h
index d3d962902e..737c761033 100644
--- a/config/examples/delta/Anycubic/Kossel/Configuration.h
+++ b/config/examples/delta/Anycubic/Kossel/Configuration.h
@@ -954,7 +954,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/delta/FLSUN/auto_calibrate/Configuration.h b/config/examples/delta/FLSUN/auto_calibrate/Configuration.h
index 5159126fb2..3f75b1402c 100644
--- a/config/examples/delta/FLSUN/auto_calibrate/Configuration.h
+++ b/config/examples/delta/FLSUN/auto_calibrate/Configuration.h
@@ -900,7 +900,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/delta/FLSUN/kossel/Configuration.h b/config/examples/delta/FLSUN/kossel/Configuration.h
index 835b20da4d..7025ce4713 100644
--- a/config/examples/delta/FLSUN/kossel/Configuration.h
+++ b/config/examples/delta/FLSUN/kossel/Configuration.h
@@ -900,7 +900,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/delta/FLSUN/kossel_mini/Configuration.h b/config/examples/delta/FLSUN/kossel_mini/Configuration.h
index 03f7f8aff3..e3827449c8 100644
--- a/config/examples/delta/FLSUN/kossel_mini/Configuration.h
+++ b/config/examples/delta/FLSUN/kossel_mini/Configuration.h
@@ -900,7 +900,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/delta/Geeetech/Rostock 301/Configuration.h b/config/examples/delta/Geeetech/Rostock 301/Configuration.h
index fb1faad21f..f21c3fd166 100644
--- a/config/examples/delta/Geeetech/Rostock 301/Configuration.h	
+++ b/config/examples/delta/Geeetech/Rostock 301/Configuration.h	
@@ -890,7 +890,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/delta/Hatchbox_Alpha/Configuration.h b/config/examples/delta/Hatchbox_Alpha/Configuration.h
index a65084bcdb..50aad9eb03 100644
--- a/config/examples/delta/Hatchbox_Alpha/Configuration.h
+++ b/config/examples/delta/Hatchbox_Alpha/Configuration.h
@@ -905,7 +905,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/delta/MKS/SBASE/Configuration.h b/config/examples/delta/MKS/SBASE/Configuration.h
index c64774614b..95799fca54 100644
--- a/config/examples/delta/MKS/SBASE/Configuration.h
+++ b/config/examples/delta/MKS/SBASE/Configuration.h
@@ -890,7 +890,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/delta/generic/Configuration.h b/config/examples/delta/generic/Configuration.h
index 5ae293d33c..8fa8b70bd9 100644
--- a/config/examples/delta/generic/Configuration.h
+++ b/config/examples/delta/generic/Configuration.h
@@ -890,7 +890,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/delta/kossel_mini/Configuration.h b/config/examples/delta/kossel_mini/Configuration.h
index b51fbf461f..0557aaaa69 100644
--- a/config/examples/delta/kossel_mini/Configuration.h
+++ b/config/examples/delta/kossel_mini/Configuration.h
@@ -890,7 +890,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/delta/kossel_pro/Configuration.h b/config/examples/delta/kossel_pro/Configuration.h
index b4ef9195b4..bca0466b60 100644
--- a/config/examples/delta/kossel_pro/Configuration.h
+++ b/config/examples/delta/kossel_pro/Configuration.h
@@ -883,7 +883,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/delta/kossel_xl/Configuration.h b/config/examples/delta/kossel_xl/Configuration.h
index d20556e3f1..c048463a68 100644
--- a/config/examples/delta/kossel_xl/Configuration.h
+++ b/config/examples/delta/kossel_xl/Configuration.h
@@ -893,7 +893,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/makibox/Configuration.h b/config/examples/makibox/Configuration.h
index 31c83cbbad..71671c8c4e 100644
--- a/config/examples/makibox/Configuration.h
+++ b/config/examples/makibox/Configuration.h
@@ -821,7 +821,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/stm32f103ret6/Configuration.h b/config/examples/stm32f103ret6/Configuration.h
index 765025ff8d..31aee8c6ea 100644
--- a/config/examples/stm32f103ret6/Configuration.h
+++ b/config/examples/stm32f103ret6/Configuration.h
@@ -820,7 +820,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/tvrrug/Round2/Configuration.h b/config/examples/tvrrug/Round2/Configuration.h
index bf2f0e5e41..9ef926d87c 100644
--- a/config/examples/tvrrug/Round2/Configuration.h
+++ b/config/examples/tvrrug/Round2/Configuration.h
@@ -813,7 +813,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE
diff --git a/config/examples/wt150/Configuration.h b/config/examples/wt150/Configuration.h
index 64fcd028f4..306c1b5b5f 100644
--- a/config/examples/wt150/Configuration.h
+++ b/config/examples/wt150/Configuration.h
@@ -823,7 +823,11 @@
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 
-  // BLTouch V3.0 and newer smart series
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
   #if ENABLED(BLTOUCH_V3)
     //#define BLTOUCH_FORCE_5V_MODE