diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h index 1a8b0b8ae7..31aaa77a9f 100644 --- a/Marlin/Configuration.h +++ b/Marlin/Configuration.h @@ -105,15 +105,24 @@ //#define SHOW_CUSTOM_BOOTSCREEN // @section machine -// SERIAL_PORT selects which serial port should be used for communication with the host. -// This allows the connection of wireless adapters (for instance) to non-default port pins. -// Serial port 0 is still used by the Arduino bootloader regardless of this setting. -// :[0,1,2,3,4,5,6,7] +/** + * Select which serial port on the board will be used for communication with the host. + * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port 0 is always used by the Arduino bootloader regardless of this setting. + * + * :[0,1,2,3,4,5,6,7] + */ #define SERIAL_PORT 0 -// This determines the communication speed of the printer -// :[2400,9600,19200,38400,57600,115200,250000] #define BAUDRATE 250000 +/** + * This setting determines the communication speed of the printer. + * + * 250000 works in most cases, but you might try a lower speed if + * you commonly experience drop-outs during host printing. + * + * :[2400,9600,19200,38400,57600,115200,250000] + */ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH @@ -169,14 +178,22 @@ //#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis //#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis -//// The following define selects which power supply you have. Please choose the one that matches your setup -// 1 = ATX -// 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC) -// :{1:'ATX',2:'X-Box 360'} -#define POWER_SUPPLY 1 +/** + * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN + * + * 0 = No Power Switch + * 1 = ATX + * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC) + * + * :{0:'No power switch',1:'ATX',2:'X-Box 360'} + */ +#define POWER_SUPPLY 0 -// Define this to have the electronics keep the power supply off on startup. If you don't know what this is leave it. -//#define PS_DEFAULT_OFF +#if POWER_SUPPLY > 0 + // Enable this option to leave the PSU off at startup. + // Power to steppers and heaters will need to be turned on with M80. + //#define PS_DEFAULT_OFF +#endif // @section temperature @@ -355,8 +372,9 @@ #define EXTRUDE_MINTEMP 170 // This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH. +// Note that for Bowden Extruders a too-small value here may prevent loading. #define PREVENT_LENGTHY_EXTRUDE -#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) +#define EXTRUDE_MAXLENGTH 200 //=========================================================================== //======================== Thermal Runaway Protection ======================= @@ -436,20 +454,56 @@ //============================================================================= // @section motion -#define DEFAULT_AXIS_STEPS_PER_UNIT {80,80,4000,500} // default steps per unit for Ultimaker -#define DEFAULT_MAX_FEEDRATE {300, 300, 5, 25} // (mm/sec) -#define DEFAULT_MAX_ACCELERATION {3000,3000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot. +/** + * Default Settings + * + * These settings can be reset by M502 + * + * Note that if EEPROM is enabled, saved values will override these. + */ + +/** + * Default Axis Steps Per Unit (steps/mm) + * Override with M92 + */ +#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 4000, 500 } + +/** + * Default Max Feed Rate (mm/s) + * Override with M203 + */ +#define DEFAULT_MAX_FEEDRATE { 300, 300, 5, 25 } + +/** + * Default Max Acceleration (change/s) change = mm/s + * Override with M201 + * + * Maximum start speed for accelerated moves: { X, Y, Z, E } + */ +#define DEFAULT_MAX_ACCELERATION { 3000, 3000, 100, 10000 } -#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration in mm/s^2 for printing moves -#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts -#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves +/** + * Default Acceleration (change/s) change = mm/s + * Override with M204 + * + * M204 P Acceleration + * M204 R Retract Acceleration + * M204 T Travel Acceleration + */ +#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration for printing moves +#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration for retracts +#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves -// "Jerk" specifies the minimum speed change that requires acceleration. -// When changing speed and direction, if the difference is less than the -// value set here, it may happen instantaneously. -#define DEFAULT_XYJERK 20.0 // (mm/sec) -#define DEFAULT_ZJERK 0.4 // (mm/sec) -#define DEFAULT_EJERK 5.0 // (mm/sec) +/** + * Defult Jerk (mm/s) + * + * "Jerk" specifies the minimum speed change that requires acceleration. + * When changing speed and direction, if the difference is less than the + * value set here, it may happen instantaneously. + */ +#define DEFAULT_XYJERK 20.0 +#define DEFAULT_ZJERK 0.4 +#define DEFAULT_EJERK 5.0 //=========================================================================== diff --git a/Marlin/example_configurations/Cartesio/Configuration.h b/Marlin/example_configurations/Cartesio/Configuration.h index 15e31ce64a..9d8e7edec4 100644 --- a/Marlin/example_configurations/Cartesio/Configuration.h +++ b/Marlin/example_configurations/Cartesio/Configuration.h @@ -355,8 +355,9 @@ #define EXTRUDE_MINTEMP 170 // This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH. +// Note that for Bowden Extruders a too-small value here may prevent loading. #define PREVENT_LENGTHY_EXTRUDE -#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) +#define EXTRUDE_MAXLENGTH 200 //=========================================================================== //======================== Thermal Runaway Protection ======================= @@ -436,20 +437,56 @@ //============================================================================= // @section motion -#define DEFAULT_AXIS_STEPS_PER_UNIT {71.128,71.128,640,152} -#define DEFAULT_MAX_FEEDRATE {200,200,20,20} // (mm/sec) -#define DEFAULT_MAX_ACCELERATION {1000,1000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot. +/** + * Default Settings + * + * These settings can be reset by M502 + * + * Note that if EEPROM is enabled, saved values will override these. + */ + +/** + * Default Axis Steps Per Unit (steps/mm) + * Override with M92 + */ +#define DEFAULT_AXIS_STEPS_PER_UNIT { 71.128, 71.128, 640, 152 } + +/** + * Default Max Feed Rate (mm/s) + * Override with M203 + */ +#define DEFAULT_MAX_FEEDRATE { 200, 200, 20, 20 } // (mm/sec) -#define DEFAULT_ACCELERATION 500 // X, Y, Z and E acceleration in mm/s^2 for printing moves -#define DEFAULT_RETRACT_ACCELERATION 10000 // E acceleration in mm/s^2 for retracts -#define DEFAULT_TRAVEL_ACCELERATION 1000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves +/** + * Default Max Acceleration (change/s) change = mm/s + * Override with M201 + * + * Maximum start speed for accelerated moves: { X, Y, Z, E } + */ +#define DEFAULT_MAX_ACCELERATION { 1000, 1000, 100, 10000 } + +/** + * Default Acceleration (change/s) change = mm/s + * Override with M204 + * + * M204 P Acceleration + * M204 R Retract Acceleration + * M204 T Travel Acceleration + */ +#define DEFAULT_ACCELERATION 500 // X, Y, Z and E acceleration for printing moves +#define DEFAULT_RETRACT_ACCELERATION 10000 // E acceleration for retracts +#define DEFAULT_TRAVEL_ACCELERATION 1000 // X, Y, Z acceleration for travel (non printing) moves -// "Jerk" specifies the minimum speed change that requires acceleration. -// When changing speed and direction, if the difference is less than the -// value set here, it may happen instantaneously. -#define DEFAULT_XYJERK 10.0 // (mm/sec) -#define DEFAULT_ZJERK 0.4 // (mm/sec) -#define DEFAULT_EJERK 5.0 // (mm/sec) +/** + * Defult Jerk (mm/s) + * + * "Jerk" specifies the minimum speed change that requires acceleration. + * When changing speed and direction, if the difference is less than the + * value set here, it may happen instantaneously. + */ +#define DEFAULT_XYJERK 10.0 +#define DEFAULT_ZJERK 0.4 +#define DEFAULT_EJERK 5.0 //=========================================================================== diff --git a/Marlin/example_configurations/Felix/Configuration.h b/Marlin/example_configurations/Felix/Configuration.h index 2c27ef7bd9..9b1ccf62d6 100644 --- a/Marlin/example_configurations/Felix/Configuration.h +++ b/Marlin/example_configurations/Felix/Configuration.h @@ -337,8 +337,9 @@ #define EXTRUDE_MINTEMP 170 // This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH. +// Note that for Bowden Extruders a too-small value here may prevent loading. #define PREVENT_LENGTHY_EXTRUDE -#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) +#define EXTRUDE_MAXLENGTH 200 //=========================================================================== //======================== Thermal Runaway Protection ======================= @@ -419,20 +420,56 @@ // @section motion // default steps per unit for Felix 2.0/3.0: 0.00249mm x/y rounding error with 3mm pitch HTD belt and 14 tooth pulleys. 0 z error. -#define DEFAULT_AXIS_STEPS_PER_UNIT {76.190476, 76.190476, 1600, 164} -#define DEFAULT_MAX_FEEDRATE {500, 500, 5, 25} // (mm/sec) -#define DEFAULT_MAX_ACCELERATION {5000,5000,100,80000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot. - -#define DEFAULT_ACCELERATION 1750 // X, Y, Z and E max acceleration in mm/s^2 for printing moves -#define DEFAULT_RETRACT_ACCELERATION 5000 // E acceleration in mm/s^2 for retracts -#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves - -// "Jerk" specifies the minimum speed change that requires acceleration. -// When changing speed and direction, if the difference is less than the -// value set here, it may happen instantaneously. -#define DEFAULT_XYJERK 10.0 // (mm/sec) -#define DEFAULT_ZJERK 0.3 // (mm/sec) -#define DEFAULT_EJERK 5.0 // (mm/sec) +/** + * Default Settings + * + * These settings can be reset by M502 + * + * Note that if EEPROM is enabled, saved values will override these. + */ + +/** + * Default Axis Steps Per Unit (steps/mm) + * Override with M92 + */ +#define DEFAULT_AXIS_STEPS_PER_UNIT { 76.190476, 76.190476, 1600, 164 } + +/** + * Default Max Feed Rate (mm/s) + * Override with M203 + */ +#define DEFAULT_MAX_FEEDRATE { 500, 500, 5, 25 } + +/** + * Default Max Acceleration (change/s) change = mm/s + * Override with M201 + * + * Maximum start speed for accelerated moves: { X, Y, Z, E } + */ +#define DEFAULT_MAX_ACCELERATION { 5000, 5000, 100, 80000 } + +/** + * Default Acceleration (change/s) change = mm/s + * Override with M204 + * + * M204 P Acceleration + * M204 R Retract Acceleration + * M204 T Travel Acceleration + */ +#define DEFAULT_ACCELERATION 1750 // X, Y, Z and E max acceleration for printing moves +#define DEFAULT_RETRACT_ACCELERATION 5000 // E acceleration for retracts +#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves + +/** + * Defult Jerk (mm/s) + * + * "Jerk" specifies the minimum speed change that requires acceleration. + * When changing speed and direction, if the difference is less than the + * value set here, it may happen instantaneously. + */ +#define DEFAULT_XYJERK 10.0 +#define DEFAULT_ZJERK 0.3 +#define DEFAULT_EJERK 5.0 //=========================================================================== diff --git a/Marlin/example_configurations/Felix/DUAL/Configuration.h b/Marlin/example_configurations/Felix/DUAL/Configuration.h index 82812ed004..476b58dbb5 100644 --- a/Marlin/example_configurations/Felix/DUAL/Configuration.h +++ b/Marlin/example_configurations/Felix/DUAL/Configuration.h @@ -335,8 +335,9 @@ #define EXTRUDE_MINTEMP 170 // This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH. +// Note that for Bowden Extruders a too-small value here may prevent loading. #define PREVENT_LENGTHY_EXTRUDE -#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) +#define EXTRUDE_MAXLENGTH 200 //=========================================================================== //======================== Thermal Runaway Protection ======================= @@ -417,20 +418,56 @@ // @section motion // default steps per unit for Felix 2.0/3.0: 0.00249mm x/y rounding error with 3mm pitch HTD belt and 14 tooth pulleys. 0 z error. -#define DEFAULT_AXIS_STEPS_PER_UNIT {76.190476, 76.190476, 1600, 164} -#define DEFAULT_MAX_FEEDRATE {500, 500, 5, 25} // (mm/sec) -#define DEFAULT_MAX_ACCELERATION {5000,5000,100,80000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot. - -#define DEFAULT_ACCELERATION 1750 // X, Y, Z and E max acceleration in mm/s^2 for printing moves -#define DEFAULT_RETRACT_ACCELERATION 5000 // E acceleration in mm/s^2 for retracts -#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves - -// "Jerk" specifies the minimum speed change that requires acceleration. -// When changing speed and direction, if the difference is less than the -// value set here, it may happen instantaneously. -#define DEFAULT_XYJERK 10.0 // (mm/sec) -#define DEFAULT_ZJERK 0.3 // (mm/sec) -#define DEFAULT_EJERK 5.0 // (mm/sec) +/** + * Default Settings + * + * These settings can be reset by M502 + * + * Note that if EEPROM is enabled, saved values will override these. + */ + +/** + * Default Axis Steps Per Unit (steps/mm) + * Override with M92 + */ +#define DEFAULT_AXIS_STEPS_PER_UNIT { 76.190476, 76.190476, 1600, 164 } + +/** + * Default Max Feed Rate (mm/s) + * Override with M203 + */ +#define DEFAULT_MAX_FEEDRATE { 500, 500, 5, 25 } + +/** + * Default Max Acceleration (change/s) change = mm/s + * Override with M201 + * + * Maximum start speed for accelerated moves: { X, Y, Z, E } + */ +#define DEFAULT_MAX_ACCELERATION { 5000, 5000, 100, 80000 } + +/** + * Default Acceleration (change/s) change = mm/s + * Override with M204 + * + * M204 P Acceleration + * M204 R Retract Acceleration + * M204 T Travel Acceleration + */ +#define DEFAULT_ACCELERATION 1750 // X, Y, Z and E max acceleration for printing moves +#define DEFAULT_RETRACT_ACCELERATION 5000 // E acceleration for retracts +#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves + +/** + * Defult Jerk (mm/s) + * + * "Jerk" specifies the minimum speed change that requires acceleration. + * When changing speed and direction, if the difference is less than the + * value set here, it may happen instantaneously. + */ +#define DEFAULT_XYJERK 10.0 +#define DEFAULT_ZJERK 0.3 +#define DEFAULT_EJERK 5.0 //=========================================================================== diff --git a/Marlin/example_configurations/Hephestos/Configuration.h b/Marlin/example_configurations/Hephestos/Configuration.h index 89d4260a53..644649857a 100644 --- a/Marlin/example_configurations/Hephestos/Configuration.h +++ b/Marlin/example_configurations/Hephestos/Configuration.h @@ -347,8 +347,9 @@ #define EXTRUDE_MINTEMP 170 // This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH. +// Note that for Bowden Extruders a too-small value here may prevent loading. #define PREVENT_LENGTHY_EXTRUDE -#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) +#define EXTRUDE_MAXLENGTH 200 //=========================================================================== //======================== Thermal Runaway Protection ======================= @@ -428,20 +429,56 @@ //============================================================================= // @section motion -#define DEFAULT_AXIS_STEPS_PER_UNIT {80,80,4000,100.47095761381482} // default steps per unit for Ultimaker -#define DEFAULT_MAX_FEEDRATE {200, 200, 3.3, 25} // (mm/sec) -#define DEFAULT_MAX_ACCELERATION {1100,1100,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot. +/** + * Default Settings + * + * These settings can be reset by M502 + * + * Note that if EEPROM is enabled, saved values will override these. + */ + +/** + * Default Axis Steps Per Unit (steps/mm) + * Override with M92 + */ +#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 4000, 100.47095761381482 } + +/** + * Default Max Feed Rate (mm/s) + * Override with M203 + */ +#define DEFAULT_MAX_FEEDRATE { 200, 200, 3.3, 25 } -#define DEFAULT_ACCELERATION 650 // X, Y, Z and E acceleration in mm/s^2 for printing moves -#define DEFAULT_RETRACT_ACCELERATION 1000 // E acceleration in mm/s^2 for retracts -#define DEFAULT_TRAVEL_ACCELERATION 1000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves +/** + * Default Max Acceleration (change/s) change = mm/s + * Override with M201 + * + * Maximum start speed for accelerated moves: { X, Y, Z, E } + */ +#define DEFAULT_MAX_ACCELERATION { 1100, 1100, 100, 10000 } + +/** + * Default Acceleration (change/s) change = mm/s + * Override with M204 + * + * M204 P Acceleration + * M204 R Retract Acceleration + * M204 T Travel Acceleration + */ +#define DEFAULT_ACCELERATION 650 // X, Y, Z and E acceleration for printing moves +#define DEFAULT_RETRACT_ACCELERATION 1000 // E acceleration for retracts +#define DEFAULT_TRAVEL_ACCELERATION 1000 // X, Y, Z acceleration for travel (non printing) moves -// "Jerk" specifies the minimum speed change that requires acceleration. -// When changing speed and direction, if the difference is less than the -// value set here, it may happen instantaneously. -#define DEFAULT_XYJERK 10.0 // (mm/sec) -#define DEFAULT_ZJERK 0.4 // (mm/sec) -#define DEFAULT_EJERK 5.0 // (mm/sec) +/** + * Defult Jerk (mm/s) + * + * "Jerk" specifies the minimum speed change that requires acceleration. + * When changing speed and direction, if the difference is less than the + * value set here, it may happen instantaneously. + */ +#define DEFAULT_XYJERK 10.0 +#define DEFAULT_ZJERK 0.4 +#define DEFAULT_EJERK 5.0 //=========================================================================== diff --git a/Marlin/example_configurations/Hephestos_2/Configuration.h b/Marlin/example_configurations/Hephestos_2/Configuration.h index 193cda0a6c..a451dd80e0 100644 --- a/Marlin/example_configurations/Hephestos_2/Configuration.h +++ b/Marlin/example_configurations/Hephestos_2/Configuration.h @@ -349,8 +349,9 @@ #define EXTRUDE_MINTEMP 170 // This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH. +// Note that for Bowden Extruders a too-small value here may prevent loading. #define PREVENT_LENGTHY_EXTRUDE -#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) +#define EXTRUDE_MAXLENGTH 200 //=========================================================================== //======================== Thermal Runaway Protection ======================= @@ -430,20 +431,56 @@ //============================================================================= // @section motion -#define DEFAULT_AXIS_STEPS_PER_UNIT {160, 160, 8000, 210.02} // Steps per unit -#define DEFAULT_MAX_FEEDRATE {250, 250, 2, 200} // mm/sec -#define DEFAULT_MAX_ACCELERATION {1000, 1000, 20, 1000} // X, Y, Z, E max start speed for accelerated moves +/** + * Default Settings + * + * These settings can be reset by M502 + * + * Note that if EEPROM is enabled, saved values will override these. + */ + +/** + * Default Axis Steps Per Unit (steps/mm) + * Override with M92 + */ +#define DEFAULT_AXIS_STEPS_PER_UNIT { 160, 160, 8000, 210.02 } + +/** + * Default Max Feed Rate (mm/s) + * Override with M203 + */ +#define DEFAULT_MAX_FEEDRATE { 250, 250, 2, 200 } -#define DEFAULT_ACCELERATION 1000 // X, Y, Z and E acceleration in mm/s^2 for printing moves -#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts -#define DEFAULT_TRAVEL_ACCELERATION 1000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves +/** + * Default Max Acceleration (change/s) change = mm/s + * Override with M201 + * + * Maximum start speed for accelerated moves: { X, Y, Z, E } + */ +#define DEFAULT_MAX_ACCELERATION { 1000, 1000, 20, 1000 } + +/** + * Default Acceleration (change/s) change = mm/s + * Override with M204 + * + * M204 P Acceleration + * M204 R Retract Acceleration + * M204 T Travel Acceleration + */ +#define DEFAULT_ACCELERATION 1000 // X, Y, Z and E acceleration for printing moves +#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration for retracts +#define DEFAULT_TRAVEL_ACCELERATION 1000 // X, Y, Z acceleration for travel (non printing) moves -// "Jerk" specifies the minimum speed change that requires acceleration. -// When changing speed and direction, if the difference is less than the -// value set here, it may happen instantaneously. -#define DEFAULT_XYJERK 20.0 // (mm/sec) -#define DEFAULT_ZJERK 0.4 // (mm/sec) -#define DEFAULT_EJERK 2.0 // (mm/sec) +/** + * Defult Jerk (mm/s) + * + * "Jerk" specifies the minimum speed change that requires acceleration. + * When changing speed and direction, if the difference is less than the + * value set here, it may happen instantaneously. + */ +#define DEFAULT_XYJERK 20.0 +#define DEFAULT_ZJERK 0.4 +#define DEFAULT_EJERK 2.0 //=========================================================================== diff --git a/Marlin/example_configurations/K8200/Configuration.h b/Marlin/example_configurations/K8200/Configuration.h index e956dedf08..f10f65570f 100644 --- a/Marlin/example_configurations/K8200/Configuration.h +++ b/Marlin/example_configurations/K8200/Configuration.h @@ -372,8 +372,9 @@ #define EXTRUDE_MINTEMP 170 // This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH. +// Note that for Bowden Extruders a too-small value here may prevent loading. #define PREVENT_LENGTHY_EXTRUDE -#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) +#define EXTRUDE_MAXLENGTH 200 //=========================================================================== //======================== Thermal Runaway Protection ======================= @@ -453,20 +454,56 @@ //============================================================================= // @section motion -#define DEFAULT_AXIS_STEPS_PER_UNIT {64.25,64.25,2560,600} // default steps per unit for K8200 -#define DEFAULT_MAX_FEEDRATE {500, 500, 5, 500} // (mm/sec) -#define DEFAULT_MAX_ACCELERATION {9000,9000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot. +/** + * Default Settings + * + * These settings can be reset by M502 + * + * Note that if EEPROM is enabled, saved values will override these. + */ + +/** + * Default Axis Steps Per Unit (steps/mm) + * Override with M92 + */ +#define DEFAULT_AXIS_STEPS_PER_UNIT { 64.25, 64.25, 2560, 600 } // default steps per unit for K8200 + +/** + * Default Max Feed Rate (mm/s) + * Override with M203 + */ +#define DEFAULT_MAX_FEEDRATE { 500, 500, 5, 500 } -#define DEFAULT_ACCELERATION 1000 // X, Y, Z and E acceleration in mm/s^2 for printing moves -#define DEFAULT_RETRACT_ACCELERATION 1000 // E acceleration in mm/s^2 for retracts -#define DEFAULT_TRAVEL_ACCELERATION 1000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves +/** + * Default Max Acceleration (change/s) change = mm/s + * Override with M201 + * + * Maximum start speed for accelerated moves: { X, Y, Z, E } + */ +#define DEFAULT_MAX_ACCELERATION { 9000, 9000, 100, 10000 } + +/** + * Default Acceleration (change/s) change = mm/s + * Override with M204 + * + * M204 P Acceleration + * M204 R Retract Acceleration + * M204 T Travel Acceleration + */ +#define DEFAULT_ACCELERATION 1000 // X, Y, Z and E acceleration for printing moves +#define DEFAULT_RETRACT_ACCELERATION 1000 // E acceleration for retracts +#define DEFAULT_TRAVEL_ACCELERATION 1000 // X, Y, Z acceleration for travel (non printing) moves -// "Jerk" specifies the minimum speed change that requires acceleration. -// When changing speed and direction, if the difference is less than the -// value set here, it may happen instantaneously. -#define DEFAULT_XYJERK 20.0 // (mm/sec) -#define DEFAULT_ZJERK 0.4 // (mm/sec) -#define DEFAULT_EJERK 5.0 // (mm/sec) +/** + * Defult Jerk (mm/s) + * + * "Jerk" specifies the minimum speed change that requires acceleration. + * When changing speed and direction, if the difference is less than the + * value set here, it may happen instantaneously. + */ +#define DEFAULT_XYJERK 20.0 +#define DEFAULT_ZJERK 0.4 +#define DEFAULT_EJERK 5.0 //=========================================================================== diff --git a/Marlin/example_configurations/K8400/Configuration.h b/Marlin/example_configurations/K8400/Configuration.h index eb8dc534c7..0c7dd0a111 100644 --- a/Marlin/example_configurations/K8400/Configuration.h +++ b/Marlin/example_configurations/K8400/Configuration.h @@ -355,8 +355,9 @@ #define EXTRUDE_MINTEMP 170 // This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH. +// Note that for Bowden Extruders a too-small value here may prevent loading. #define PREVENT_LENGTHY_EXTRUDE -#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) +#define EXTRUDE_MAXLENGTH 200 //=========================================================================== //======================== Thermal Runaway Protection ======================= @@ -436,20 +437,56 @@ //============================================================================= // @section motion -#define DEFAULT_AXIS_STEPS_PER_UNIT {134.74,134.74,4266.66,148.7} // default steps per unit for Ultimaker -#define DEFAULT_MAX_FEEDRATE {160, 160, 10, 10000} // (mm/sec) -#define DEFAULT_MAX_ACCELERATION {9000,9000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot. +/** + * Default Settings + * + * These settings can be reset by M502 + * + * Note that if EEPROM is enabled, saved values will override these. + */ + +/** + * Default Axis Steps Per Unit (steps/mm) + * Override with M92 + */ +#define DEFAULT_AXIS_STEPS_PER_UNIT { 134.74, 134.74, 4266.66, 148.7 } + +/** + * Default Max Feed Rate (mm/s) + * Override with M203 + */ +#define DEFAULT_MAX_FEEDRATE { 160, 160, 10, 10000 } -#define DEFAULT_ACCELERATION 6000 // X, Y, Z and E acceleration in mm/s^2 for printing moves -#define DEFAULT_RETRACT_ACCELERATION 6000 // E acceleration in mm/s^2 for retracts -#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves +/** + * Default Max Acceleration (change/s) change = mm/s + * Override with M201 + * + * Maximum start speed for accelerated moves: { X, Y, Z, E } + */ +#define DEFAULT_MAX_ACCELERATION { 9000, 9000, 100, 10000 } + +/** + * Default Acceleration (change/s) change = mm/s + * Override with M204 + * + * M204 P Acceleration + * M204 R Retract Acceleration + * M204 T Travel Acceleration + */ +#define DEFAULT_ACCELERATION 6000 // X, Y, Z and E acceleration for printing moves +#define DEFAULT_RETRACT_ACCELERATION 6000 // E acceleration for retracts +#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves -// "Jerk" specifies the minimum speed change that requires acceleration. -// When changing speed and direction, if the difference is less than the -// value set here, it may happen instantaneously. -#define DEFAULT_XYJERK 10.0 // (mm/sec) -#define DEFAULT_ZJERK 0.5 // (mm/sec) -#define DEFAULT_EJERK 20.0 // (mm/sec) +/** + * Defult Jerk (mm/s) + * + * "Jerk" specifies the minimum speed change that requires acceleration. + * When changing speed and direction, if the difference is less than the + * value set here, it may happen instantaneously. + */ +#define DEFAULT_XYJERK 10.0 +#define DEFAULT_ZJERK 0.5 +#define DEFAULT_EJERK 20.0 //=========================================================================== diff --git a/Marlin/example_configurations/K8400/Dual-head/Configuration.h b/Marlin/example_configurations/K8400/Dual-head/Configuration.h index 5bfe8422a3..837ee9815d 100644 --- a/Marlin/example_configurations/K8400/Dual-head/Configuration.h +++ b/Marlin/example_configurations/K8400/Dual-head/Configuration.h @@ -355,8 +355,9 @@ #define EXTRUDE_MINTEMP 170 // This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH. +// Note that for Bowden Extruders a too-small value here may prevent loading. #define PREVENT_LENGTHY_EXTRUDE -#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) +#define EXTRUDE_MAXLENGTH 200 //=========================================================================== //======================== Thermal Runaway Protection ======================= @@ -436,20 +437,56 @@ //============================================================================= // @section motion -#define DEFAULT_AXIS_STEPS_PER_UNIT {134.74,134.74,4266.66,148.7} // default steps per unit for Ultimaker -#define DEFAULT_MAX_FEEDRATE {160, 160, 10, 10000} // (mm/sec) -#define DEFAULT_MAX_ACCELERATION {9000,9000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot. +/** + * Default Settings + * + * These settings can be reset by M502 + * + * Note that if EEPROM is enabled, saved values will override these. + */ + +/** + * Default Axis Steps Per Unit (steps/mm) + * Override with M92 + */ +#define DEFAULT_AXIS_STEPS_PER_UNIT { 134.74, 134.74, 4266.66, 148.7 } + +/** + * Default Max Feed Rate (mm/s) + * Override with M203 + */ +#define DEFAULT_MAX_FEEDRATE { 160, 160, 10, 10000 } -#define DEFAULT_ACCELERATION 6000 // X, Y, Z and E acceleration in mm/s^2 for printing moves -#define DEFAULT_RETRACT_ACCELERATION 6000 // E acceleration in mm/s^2 for retracts -#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves +/** + * Default Max Acceleration (change/s) change = mm/s + * Override with M201 + * + * Maximum start speed for accelerated moves: { X, Y, Z, E } + */ +#define DEFAULT_MAX_ACCELERATION { 9000, 9000, 100, 10000 } + +/** + * Default Acceleration (change/s) change = mm/s + * Override with M204 + * + * M204 P Acceleration + * M204 R Retract Acceleration + * M204 T Travel Acceleration + */ +#define DEFAULT_ACCELERATION 6000 // X, Y, Z and E acceleration for printing moves +#define DEFAULT_RETRACT_ACCELERATION 6000 // E acceleration for retracts +#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves -// "Jerk" specifies the minimum speed change that requires acceleration. -// When changing speed and direction, if the difference is less than the -// value set here, it may happen instantaneously. -#define DEFAULT_XYJERK 10.0 // (mm/sec) -#define DEFAULT_ZJERK 0.5 // (mm/sec) -#define DEFAULT_EJERK 20.0 // (mm/sec) +/** + * Defult Jerk (mm/s) + * + * "Jerk" specifies the minimum speed change that requires acceleration. + * When changing speed and direction, if the difference is less than the + * value set here, it may happen instantaneously. + */ +#define DEFAULT_XYJERK 10.0 +#define DEFAULT_ZJERK 0.5 +#define DEFAULT_EJERK 20.0 //=========================================================================== diff --git a/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h b/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h index 21e3d5c4c4..b61e44705f 100644 --- a/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h +++ b/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h @@ -355,8 +355,9 @@ #define EXTRUDE_MINTEMP 170 // This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH. +// Note that for Bowden Extruders a too-small value here may prevent loading. #define PREVENT_LENGTHY_EXTRUDE -#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) +#define EXTRUDE_MAXLENGTH 200 //=========================================================================== //======================== Thermal Runaway Protection ======================= @@ -436,20 +437,56 @@ //============================================================================= // @section motion -#define DEFAULT_AXIS_STEPS_PER_UNIT {78.7402*2,78.7402*2,5120.00,760*1*1.5} // default steps per unit for Ultimaker -#define DEFAULT_MAX_FEEDRATE {300, 300, 5, 25} // (mm/sec) -#define DEFAULT_MAX_ACCELERATION {3000,3000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot. +/** + * Default Settings + * + * These settings can be reset by M502 + * + * Note that if EEPROM is enabled, saved values will override these. + */ + +/** + * Default Axis Steps Per Unit (steps/mm) + * Override with M92 + */ +#define DEFAULT_AXIS_STEPS_PER_UNIT {78.7402*2,78.7402*2,5120.00,760*1*1.5} + +/** + * Default Max Feed Rate (mm/s) + * Override with M203 + */ +#define DEFAULT_MAX_FEEDRATE { 300, 300, 5, 25 } -#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration in mm/s^2 for printing moves -#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts -#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves +/** + * Default Max Acceleration (change/s) change = mm/s + * Override with M201 + * + * Maximum start speed for accelerated moves: { X, Y, Z, E } + */ +#define DEFAULT_MAX_ACCELERATION { 3000, 3000, 100, 10000 } + +/** + * Default Acceleration (change/s) change = mm/s + * Override with M204 + * + * M204 P Acceleration + * M204 R Retract Acceleration + * M204 T Travel Acceleration + */ +#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration for printing moves +#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration for retracts +#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves -// "Jerk" specifies the minimum speed change that requires acceleration. -// When changing speed and direction, if the difference is less than the -// value set here, it may happen instantaneously. -#define DEFAULT_XYJERK 20.0 // (mm/sec) -#define DEFAULT_ZJERK 0.4 // (mm/sec) -#define DEFAULT_EJERK 5.0 // (mm/sec) +/** + * Defult Jerk (mm/s) + * + * "Jerk" specifies the minimum speed change that requires acceleration. + * When changing speed and direction, if the difference is less than the + * value set here, it may happen instantaneously. + */ +#define DEFAULT_XYJERK 20.0 +#define DEFAULT_ZJERK 0.4 +#define DEFAULT_EJERK 5.0 //=========================================================================== diff --git a/Marlin/example_configurations/RigidBot/Configuration.h b/Marlin/example_configurations/RigidBot/Configuration.h index df2071cf05..d41b210cfa 100644 --- a/Marlin/example_configurations/RigidBot/Configuration.h +++ b/Marlin/example_configurations/RigidBot/Configuration.h @@ -352,8 +352,9 @@ #define EXTRUDE_MINTEMP 170 // This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH. +// Note that for Bowden Extruders a too-small value here may prevent loading. #define PREVENT_LENGTHY_EXTRUDE -#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) +#define EXTRUDE_MAXLENGTH 200 //=========================================================================== //======================== Thermal Runaway Protection ======================= @@ -433,21 +434,57 @@ //============================================================================= // @section motion -#define DEFAULT_AXIS_STEPS_PER_UNIT {44.3090, 22.1545, 1600, 53.5} // default steps per unit for RigidBot with standard hardware - // default steps for 16-tooth pulleys {100.06,50.06,1600,76}, HPX2-MAX E=504, RigidBot E=53.5, Peter Stoneham's=76 -#define DEFAULT_MAX_FEEDRATE {500, 500, 5, 25} // (mm/sec) -#define DEFAULT_MAX_ACCELERATION {800, 800, 100, 10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot. - -#define DEFAULT_ACCELERATION 600 // X, Y, Z and E acceleration in mm/s^2 for printing moves -#define DEFAULT_RETRACT_ACCELERATION 1000 // E acceleration in mm/s^2 for retracts -#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves - -// "Jerk" specifies the minimum speed change that requires acceleration. -// When changing speed and direction, if the difference is less than the -// value set here, it may happen instantaneously. -#define DEFAULT_XYJERK 8.0 // (mm/sec) -#define DEFAULT_ZJERK 0.4 // (mm/sec) -#define DEFAULT_EJERK 5.0 // (mm/sec) +/** + * Default Settings + * + * These settings can be reset by M502 + * + * Note that if EEPROM is enabled, saved values will override these. + */ + +/** + * Default Axis Steps Per Unit (steps/mm) + * Override with M92 + */ +#define DEFAULT_AXIS_STEPS_PER_UNIT { 44.3090, 22.1545, 1600, 53.5 } // default steps per unit for RigidBot with standard hardware + // default steps for 16-tooth pulleys { 100.06, 50.06, 1600, 76 }, HPX2-MAX E=504, RigidBot E=53.5, Peter Stoneham's=76 + +/** + * Default Max Feed Rate (mm/s) + * Override with M203 + */ +#define DEFAULT_MAX_FEEDRATE { 500, 500, 5, 25 } + +/** + * Default Max Acceleration (change/s) change = mm/s + * Override with M201 + * + * Maximum start speed for accelerated moves: { X, Y, Z, E } + */ +#define DEFAULT_MAX_ACCELERATION { 800, 800, 100, 10000 } + +/** + * Default Acceleration (change/s) change = mm/s + * Override with M204 + * + * M204 P Acceleration + * M204 R Retract Acceleration + * M204 T Travel Acceleration + */ +#define DEFAULT_ACCELERATION 600 // X, Y, Z and E acceleration for printing moves +#define DEFAULT_RETRACT_ACCELERATION 1000 // E acceleration for retracts +#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves + +/** + * Defult Jerk (mm/s) + * + * "Jerk" specifies the minimum speed change that requires acceleration. + * When changing speed and direction, if the difference is less than the + * value set here, it may happen instantaneously. + */ +#define DEFAULT_XYJERK 8.0 +#define DEFAULT_ZJERK 0.4 +#define DEFAULT_EJERK 5.0 //=========================================================================== diff --git a/Marlin/example_configurations/SCARA/Configuration.h b/Marlin/example_configurations/SCARA/Configuration.h index 3c2e96a696..e50306c44f 100644 --- a/Marlin/example_configurations/SCARA/Configuration.h +++ b/Marlin/example_configurations/SCARA/Configuration.h @@ -365,8 +365,9 @@ #define EXTRUDE_MINTEMP 170 // This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH. +// Note that for Bowden Extruders a too-small value here may prevent loading. #define PREVENT_LENGTHY_EXTRUDE -#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) +#define EXTRUDE_MAXLENGTH 200 //=========================================================================== //======================== Thermal Runaway Protection ======================= @@ -446,20 +447,56 @@ //============================================================================= // @section motion +/** + * Default Settings + * + * These settings can be reset by M502 + * + * Note that if EEPROM is enabled, saved values will override these. + */ + +/** + * Default Axis Steps Per Unit (steps/mm) + * Override with M92 + */ #define DEFAULT_AXIS_STEPS_PER_UNIT {103.69,106.65,200/1.25,1000} // default steps per unit for SCARA -#define DEFAULT_MAX_FEEDRATE {300, 300, 30, 25} // (mm/sec) -#define DEFAULT_MAX_ACCELERATION {300,300,20,1000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot. - -#define DEFAULT_ACCELERATION 400 // X, Y, Z and E acceleration in mm/s^2 for printing moves -#define DEFAULT_RETRACT_ACCELERATION 2000 // E acceleration in mm/s^2 for retracts -#define DEFAULT_TRAVEL_ACCELERATION 400 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves - -// "Jerk" specifies the minimum speed change that requires acceleration. -// When changing speed and direction, if the difference is less than the -// value set here, it may happen instantaneously. -#define DEFAULT_XYJERK 5.0 // (mm/sec) -#define DEFAULT_ZJERK 0.4 // (mm/sec) -#define DEFAULT_EJERK 3.0 // (mm/sec) + +/** + * Default Max Feed Rate (mm/s) + * Override with M203 + */ +#define DEFAULT_MAX_FEEDRATE { 300, 300, 30, 25 } + +/** + * Default Max Acceleration (change/s) change = mm/s + * Override with M201 + * + * Maximum start speed for accelerated moves: { X, Y, Z, E } + */ +#define DEFAULT_MAX_ACCELERATION { 300, 300, 20, 1000 } + +/** + * Default Acceleration (change/s) change = mm/s + * Override with M204 + * + * M204 P Acceleration + * M204 R Retract Acceleration + * M204 T Travel Acceleration + */ +#define DEFAULT_ACCELERATION 400 // X, Y, Z and E acceleration for printing moves +#define DEFAULT_RETRACT_ACCELERATION 2000 // E acceleration for retracts +#define DEFAULT_TRAVEL_ACCELERATION 400 // X, Y, Z acceleration for travel (non printing) moves + +/** + * Defult Jerk (mm/s) + * + * "Jerk" specifies the minimum speed change that requires acceleration. + * When changing speed and direction, if the difference is less than the + * value set here, it may happen instantaneously. + */ +#define DEFAULT_XYJERK 5.0 +#define DEFAULT_ZJERK 0.4 +#define DEFAULT_EJERK 3.0 //=========================================================================== diff --git a/Marlin/example_configurations/TAZ4/Configuration.h b/Marlin/example_configurations/TAZ4/Configuration.h index 96c6e8cee6..fc78d56989 100644 --- a/Marlin/example_configurations/TAZ4/Configuration.h +++ b/Marlin/example_configurations/TAZ4/Configuration.h @@ -376,8 +376,9 @@ #define EXTRUDE_MINTEMP 170 // This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH. +// Note that for Bowden Extruders a too-small value here may prevent loading. #define PREVENT_LENGTHY_EXTRUDE -#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) +#define EXTRUDE_MAXLENGTH 200 //=========================================================================== //======================== Thermal Runaway Protection ======================= @@ -457,20 +458,56 @@ //============================================================================= // @section motion -#define DEFAULT_AXIS_STEPS_PER_UNIT {100.5,100.5,400,850} // default steps per unit for Ultimaker -#define DEFAULT_MAX_FEEDRATE {800, 800, 8, 50} // (mm/sec) -#define DEFAULT_MAX_ACCELERATION {9000,9000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot. +/** + * Default Settings + * + * These settings can be reset by M502 + * + * Note that if EEPROM is enabled, saved values will override these. + */ + +/** + * Default Axis Steps Per Unit (steps/mm) + * Override with M92 + */ +#define DEFAULT_AXIS_STEPS_PER_UNIT { 100.5, 100.5, 400, 850 } + +/** + * Default Max Feed Rate (mm/s) + * Override with M203 + */ +#define DEFAULT_MAX_FEEDRATE { 800, 800, 8, 50 } -#define DEFAULT_ACCELERATION 500 // X, Y, Z and E acceleration in mm/s^2 for printing moves -#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts -#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves +/** + * Default Max Acceleration (change/s) change = mm/s + * Override with M201 + * + * Maximum start speed for accelerated moves: { X, Y, Z, E } + */ +#define DEFAULT_MAX_ACCELERATION { 9000, 9000, 100, 10000 } + +/** + * Default Acceleration (change/s) change = mm/s + * Override with M204 + * + * M204 P Acceleration + * M204 R Retract Acceleration + * M204 T Travel Acceleration + */ +#define DEFAULT_ACCELERATION 500 // X, Y, Z and E acceleration for printing moves +#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration for retracts +#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves -// "Jerk" specifies the minimum speed change that requires acceleration. -// When changing speed and direction, if the difference is less than the -// value set here, it may happen instantaneously. -#define DEFAULT_XYJERK 8.0 // (mm/sec) -#define DEFAULT_ZJERK 0.4 // (mm/sec) -#define DEFAULT_EJERK 10.0 // (mm/sec) +/** + * Defult Jerk (mm/s) + * + * "Jerk" specifies the minimum speed change that requires acceleration. + * When changing speed and direction, if the difference is less than the + * value set here, it may happen instantaneously. + */ +#define DEFAULT_XYJERK 8.0 +#define DEFAULT_ZJERK 0.4 +#define DEFAULT_EJERK 10.0 //=========================================================================== diff --git a/Marlin/example_configurations/WITBOX/Configuration.h b/Marlin/example_configurations/WITBOX/Configuration.h index 7737824d10..7647e7eaf0 100644 --- a/Marlin/example_configurations/WITBOX/Configuration.h +++ b/Marlin/example_configurations/WITBOX/Configuration.h @@ -347,8 +347,9 @@ #define EXTRUDE_MINTEMP 170 // This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH. +// Note that for Bowden Extruders a too-small value here may prevent loading. #define PREVENT_LENGTHY_EXTRUDE -#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) +#define EXTRUDE_MAXLENGTH 200 //=========================================================================== //======================== Thermal Runaway Protection ======================= @@ -428,20 +429,56 @@ //============================================================================= // @section motion -#define DEFAULT_AXIS_STEPS_PER_UNIT {80,80,600.0*8/3,102.073} // default steps per unit for Ultimaker -#define DEFAULT_MAX_FEEDRATE {350, 350, 7.2, 80} // (mm/sec) -#define DEFAULT_MAX_ACCELERATION {1000,1000,10,1000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot. +/** + * Default Settings + * + * These settings can be reset by M502 + * + * Note that if EEPROM is enabled, saved values will override these. + */ + +/** + * Default Axis Steps Per Unit (steps/mm) + * Override with M92 + */ +#define DEFAULT_AXIS_STEPS_PER_UNIT {80,80,600.0*8/3,102.073} + +/** + * Default Max Feed Rate (mm/s) + * Override with M203 + */ +#define DEFAULT_MAX_FEEDRATE { 350, 350, 7.2, 80 } -#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration in mm/s^2 for printing moves -#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts -#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves +/** + * Default Max Acceleration (change/s) change = mm/s + * Override with M201 + * + * Maximum start speed for accelerated moves: { X, Y, Z, E } + */ +#define DEFAULT_MAX_ACCELERATION { 1000, 1000, 10, 1000 } + +/** + * Default Acceleration (change/s) change = mm/s + * Override with M204 + * + * M204 P Acceleration + * M204 R Retract Acceleration + * M204 T Travel Acceleration + */ +#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration for printing moves +#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration for retracts +#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves -// "Jerk" specifies the minimum speed change that requires acceleration. -// When changing speed and direction, if the difference is less than the -// value set here, it may happen instantaneously. -#define DEFAULT_XYJERK 10.0 // (mm/sec) -#define DEFAULT_ZJERK 0.4 // (mm/sec) -#define DEFAULT_EJERK 5.0 // (mm/sec) +/** + * Defult Jerk (mm/s) + * + * "Jerk" specifies the minimum speed change that requires acceleration. + * When changing speed and direction, if the difference is less than the + * value set here, it may happen instantaneously. + */ +#define DEFAULT_XYJERK 10.0 +#define DEFAULT_ZJERK 0.4 +#define DEFAULT_EJERK 5.0 //=========================================================================== diff --git a/Marlin/example_configurations/adafruit/ST7565/Configuration.h b/Marlin/example_configurations/adafruit/ST7565/Configuration.h index 956ba62119..0fe8218ab8 100644 --- a/Marlin/example_configurations/adafruit/ST7565/Configuration.h +++ b/Marlin/example_configurations/adafruit/ST7565/Configuration.h @@ -355,8 +355,9 @@ #define EXTRUDE_MINTEMP 170 // This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH. +// Note that for Bowden Extruders a too-small value here may prevent loading. #define PREVENT_LENGTHY_EXTRUDE -#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) +#define EXTRUDE_MAXLENGTH 200 //=========================================================================== //======================== Thermal Runaway Protection ======================= @@ -436,20 +437,56 @@ //============================================================================= // @section motion -#define DEFAULT_AXIS_STEPS_PER_UNIT {80,80,4000,500} // default steps per unit for Ultimaker -#define DEFAULT_MAX_FEEDRATE {300, 300, 5, 25} // (mm/sec) -#define DEFAULT_MAX_ACCELERATION {3000,3000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot. +/** + * Default Settings + * + * These settings can be reset by M502 + * + * Note that if EEPROM is enabled, saved values will override these. + */ + +/** + * Default Axis Steps Per Unit (steps/mm) + * Override with M92 + */ +#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 4000, 500 } + +/** + * Default Max Feed Rate (mm/s) + * Override with M203 + */ +#define DEFAULT_MAX_FEEDRATE { 300, 300, 5, 25 } -#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration in mm/s^2 for printing moves -#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts -#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves +/** + * Default Max Acceleration (change/s) change = mm/s + * Override with M201 + * + * Maximum start speed for accelerated moves: { X, Y, Z, E } + */ +#define DEFAULT_MAX_ACCELERATION { 3000, 3000, 100, 10000 } + +/** + * Default Acceleration (change/s) change = mm/s + * Override with M204 + * + * M204 P Acceleration + * M204 R Retract Acceleration + * M204 T Travel Acceleration + */ +#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration for printing moves +#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration for retracts +#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves -// "Jerk" specifies the minimum speed change that requires acceleration. -// When changing speed and direction, if the difference is less than the -// value set here, it may happen instantaneously. -#define DEFAULT_XYJERK 20.0 // (mm/sec) -#define DEFAULT_ZJERK 0.4 // (mm/sec) -#define DEFAULT_EJERK 5.0 // (mm/sec) +/** + * Defult Jerk (mm/s) + * + * "Jerk" specifies the minimum speed change that requires acceleration. + * When changing speed and direction, if the difference is less than the + * value set here, it may happen instantaneously. + */ +#define DEFAULT_XYJERK 20.0 +#define DEFAULT_ZJERK 0.4 +#define DEFAULT_EJERK 5.0 //=========================================================================== diff --git a/Marlin/example_configurations/delta/biv2.5/Configuration.h b/Marlin/example_configurations/delta/biv2.5/Configuration.h index 51992a33fb..6612004329 100644 --- a/Marlin/example_configurations/delta/biv2.5/Configuration.h +++ b/Marlin/example_configurations/delta/biv2.5/Configuration.h @@ -355,8 +355,9 @@ #define EXTRUDE_MINTEMP 170 // This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH. +// Note that for Bowden Extruders a too-small value here may prevent loading. #define PREVENT_LENGTHY_EXTRUDE -#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) +#define EXTRUDE_MAXLENGTH 200 //=========================================================================== //======================== Thermal Runaway Protection ======================= @@ -479,20 +480,56 @@ // @section motion // delta speeds must be the same on xyz -#define DEFAULT_AXIS_STEPS_PER_UNIT {72.9, 72.9, 72.9, 291} // default steps per unit for BI v2.5 (cable drive) -#define DEFAULT_MAX_FEEDRATE {500, 500, 500, 150} // (mm/sec) -#define DEFAULT_MAX_ACCELERATION {9000,9000,9000,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot. - -#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration in mm/s^2 for printing moves -#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts -#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves - -// "Jerk" specifies the minimum speed change that requires acceleration. -// When changing speed and direction, if the difference is less than the -// value set here, it may happen instantaneously. -#define DEFAULT_XYJERK 15.0 // (mm/sec) -#define DEFAULT_ZJERK 15.0 // (mm/sec) Must be same as XY for delta -#define DEFAULT_EJERK 5.0 // (mm/sec) +/** + * Default Settings + * + * These settings can be reset by M502 + * + * Note that if EEPROM is enabled, saved values will override these. + */ + +/** + * Default Axis Steps Per Unit (steps/mm) + * Override with M92 + */ +#define DEFAULT_AXIS_STEPS_PER_UNIT { 72.9, 72.9, 72.9, 291 } // default steps per unit for BI v2.5 (cable drive) + +/** + * Default Max Feed Rate (mm/s) + * Override with M203 + */ +#define DEFAULT_MAX_FEEDRATE { 500, 500, 500, 150 } + +/** + * Default Max Acceleration (change/s) change = mm/s + * Override with M201 + * + * Maximum start speed for accelerated moves: { X, Y, Z, E } + */ +#define DEFAULT_MAX_ACCELERATION { 9000, 9000, 9000, 10000 } + +/** + * Default Acceleration (change/s) change = mm/s + * Override with M204 + * + * M204 P Acceleration + * M204 R Retract Acceleration + * M204 T Travel Acceleration + */ +#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration for printing moves +#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration for retracts +#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves + +/** + * Defult Jerk (mm/s) + * + * "Jerk" specifies the minimum speed change that requires acceleration. + * When changing speed and direction, if the difference is less than the + * value set here, it may happen instantaneously. + */ +#define DEFAULT_XYJERK 15.0 +#define DEFAULT_ZJERK 15.0 // Must be same as XY for delta +#define DEFAULT_EJERK 5.0 //=========================================================================== diff --git a/Marlin/example_configurations/delta/generic/Configuration.h b/Marlin/example_configurations/delta/generic/Configuration.h index d9603847b5..6ec9217c0c 100644 --- a/Marlin/example_configurations/delta/generic/Configuration.h +++ b/Marlin/example_configurations/delta/generic/Configuration.h @@ -355,8 +355,9 @@ #define EXTRUDE_MINTEMP 170 // This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH. +// Note that for Bowden Extruders a too-small value here may prevent loading. #define PREVENT_LENGTHY_EXTRUDE -#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) +#define EXTRUDE_MAXLENGTH 200 //=========================================================================== //======================== Thermal Runaway Protection ======================= @@ -479,20 +480,56 @@ // @section motion // delta speeds must be the same on xyz +/** + * Default Settings + * + * These settings can be reset by M502 + * + * Note that if EEPROM is enabled, saved values will override these. + */ + +/** + * Default Axis Steps Per Unit (steps/mm) + * Override with M92 + */ #define DEFAULT_AXIS_STEPS_PER_UNIT {80, 80, 80, 760*1.1} // default steps per unit for Kossel (GT2, 20 tooth) -#define DEFAULT_MAX_FEEDRATE {500, 500, 500, 25} // (mm/sec) -#define DEFAULT_MAX_ACCELERATION {9000,9000,9000,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot. - -#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration in mm/s^2 for printing moves -#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts -#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves - -// "Jerk" specifies the minimum speed change that requires acceleration. -// When changing speed and direction, if the difference is less than the -// value set here, it may happen instantaneously. -#define DEFAULT_XYJERK 20.0 // (mm/sec) -#define DEFAULT_ZJERK 20.0 // (mm/sec) Must be same as XY for delta -#define DEFAULT_EJERK 5.0 // (mm/sec) + +/** + * Default Max Feed Rate (mm/s) + * Override with M203 + */ +#define DEFAULT_MAX_FEEDRATE { 500, 500, 500, 25 } + +/** + * Default Max Acceleration (change/s) change = mm/s + * Override with M201 + * + * Maximum start speed for accelerated moves: { X, Y, Z, E } + */ +#define DEFAULT_MAX_ACCELERATION { 9000, 9000, 9000, 10000 } + +/** + * Default Acceleration (change/s) change = mm/s + * Override with M204 + * + * M204 P Acceleration + * M204 R Retract Acceleration + * M204 T Travel Acceleration + */ +#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration for printing moves +#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration for retracts +#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves + +/** + * Defult Jerk (mm/s) + * + * "Jerk" specifies the minimum speed change that requires acceleration. + * When changing speed and direction, if the difference is less than the + * value set here, it may happen instantaneously. + */ +#define DEFAULT_XYJERK 20.0 +#define DEFAULT_ZJERK 20.0 // Must be same as XY for delta +#define DEFAULT_EJERK 5.0 //=========================================================================== diff --git a/Marlin/example_configurations/delta/kossel_mini/Configuration.h b/Marlin/example_configurations/delta/kossel_mini/Configuration.h index 77251f932f..cb136b1589 100644 --- a/Marlin/example_configurations/delta/kossel_mini/Configuration.h +++ b/Marlin/example_configurations/delta/kossel_mini/Configuration.h @@ -355,8 +355,9 @@ #define EXTRUDE_MINTEMP 170 // This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH. +// Note that for Bowden Extruders a too-small value here may prevent loading. #define PREVENT_LENGTHY_EXTRUDE -#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) +#define EXTRUDE_MAXLENGTH 200 //=========================================================================== //======================== Thermal Runaway Protection ======================= @@ -479,20 +480,56 @@ // @section motion // delta speeds must be the same on xyz +/** + * Default Settings + * + * These settings can be reset by M502 + * + * Note that if EEPROM is enabled, saved values will override these. + */ + +/** + * Default Axis Steps Per Unit (steps/mm) + * Override with M92 + */ #define DEFAULT_AXIS_STEPS_PER_UNIT {80, 80, 80, 760*1.1} // default steps per unit for Kossel (GT2, 20 tooth) -#define DEFAULT_MAX_FEEDRATE {500, 500, 500, 25} // (mm/sec) -#define DEFAULT_MAX_ACCELERATION {9000,9000,9000,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot. - -#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration in mm/s^2 for printing moves -#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts -#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves - -// "Jerk" specifies the minimum speed change that requires acceleration. -// When changing speed and direction, if the difference is less than the -// value set here, it may happen instantaneously. -#define DEFAULT_XYJERK 20.0 // (mm/sec) -#define DEFAULT_ZJERK 20.0 // (mm/sec) Must be same as XY for delta -#define DEFAULT_EJERK 5.0 // (mm/sec) + +/** + * Default Max Feed Rate (mm/s) + * Override with M203 + */ +#define DEFAULT_MAX_FEEDRATE { 500, 500, 500, 25 } + +/** + * Default Max Acceleration (change/s) change = mm/s + * Override with M201 + * + * Maximum start speed for accelerated moves: { X, Y, Z, E } + */ +#define DEFAULT_MAX_ACCELERATION { 9000, 9000, 9000, 10000 } + +/** + * Default Acceleration (change/s) change = mm/s + * Override with M204 + * + * M204 P Acceleration + * M204 R Retract Acceleration + * M204 T Travel Acceleration + */ +#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration for printing moves +#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration for retracts +#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves + +/** + * Defult Jerk (mm/s) + * + * "Jerk" specifies the minimum speed change that requires acceleration. + * When changing speed and direction, if the difference is less than the + * value set here, it may happen instantaneously. + */ +#define DEFAULT_XYJERK 20.0 +#define DEFAULT_ZJERK 20.0 // Must be same as XY for delta +#define DEFAULT_EJERK 5.0 //=========================================================================== diff --git a/Marlin/example_configurations/delta/kossel_pro/Configuration.h b/Marlin/example_configurations/delta/kossel_pro/Configuration.h index 2cc9fbf5e3..d0dc57e903 100644 --- a/Marlin/example_configurations/delta/kossel_pro/Configuration.h +++ b/Marlin/example_configurations/delta/kossel_pro/Configuration.h @@ -344,8 +344,9 @@ #define EXTRUDE_MINTEMP 170 // This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH. +// Note that for Bowden Extruders a too-small value here may prevent loading. #define PREVENT_LENGTHY_EXTRUDE -#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) +#define EXTRUDE_MAXLENGTH 200 //=========================================================================== //======================== Thermal Runaway Protection ======================= @@ -475,20 +476,56 @@ // delta speeds must be the same on xyz #define XYZ_STEPS ((XYZ_FULL_STEPS_PER_ROTATION) * (XYZ_MICROSTEPS) / double(XYZ_BELT_PITCH) / double(XYZ_PULLEY_TEETH)) +/** + * Default Settings + * + * These settings can be reset by M502 + * + * Note that if EEPROM is enabled, saved values will override these. + */ + +/** + * Default Axis Steps Per Unit (steps/mm) + * Override with M92 + */ #define DEFAULT_AXIS_STEPS_PER_UNIT {XYZ_STEPS, XYZ_STEPS, XYZ_STEPS, 184.8} -#define DEFAULT_MAX_FEEDRATE {200, 200, 200, 200} // (mm/sec) -#define DEFAULT_MAX_ACCELERATION {9000,9000,9000,9000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot. - -#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration in mm/s^2 for printing moves -#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts -#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves - -// "Jerk" specifies the minimum speed change that requires acceleration. -// When changing speed and direction, if the difference is less than the -// value set here, it may happen instantaneously. -#define DEFAULT_XYJERK 20.0 // (mm/sec) -#define DEFAULT_ZJERK 20.0 // (mm/sec) Must be same as XY for delta -#define DEFAULT_EJERK 5.0 // (mm/sec) + +/** + * Default Max Feed Rate (mm/s) + * Override with M203 + */ +#define DEFAULT_MAX_FEEDRATE { 200, 200, 200, 200 } + +/** + * Default Max Acceleration (change/s) change = mm/s + * Override with M201 + * + * Maximum start speed for accelerated moves: { X, Y, Z, E } + */ +#define DEFAULT_MAX_ACCELERATION { 9000, 9000, 9000, 9000 } + +/** + * Default Acceleration (change/s) change = mm/s + * Override with M204 + * + * M204 P Acceleration + * M204 R Retract Acceleration + * M204 T Travel Acceleration + */ +#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration for printing moves +#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration for retracts +#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves + +/** + * Defult Jerk (mm/s) + * + * "Jerk" specifies the minimum speed change that requires acceleration. + * When changing speed and direction, if the difference is less than the + * value set here, it may happen instantaneously. + */ +#define DEFAULT_XYJERK 20.0 +#define DEFAULT_ZJERK 20.0 // Must be same as XY for delta +#define DEFAULT_EJERK 5.0 //=========================================================================== diff --git a/Marlin/example_configurations/delta/kossel_xl/Configuration.h b/Marlin/example_configurations/delta/kossel_xl/Configuration.h index 6725e2dd70..42c9d50843 100644 --- a/Marlin/example_configurations/delta/kossel_xl/Configuration.h +++ b/Marlin/example_configurations/delta/kossel_xl/Configuration.h @@ -353,8 +353,9 @@ #define EXTRUDE_MINTEMP 170 // This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH. +// Note that for Bowden Extruders a too-small value here may prevent loading. #define PREVENT_LENGTHY_EXTRUDE -#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) +#define EXTRUDE_MAXLENGTH 200 //=========================================================================== //======================== Thermal Runaway Protection ======================= @@ -485,20 +486,56 @@ // delta speeds must be the same on xyz #define XYZ_STEPS (XYZ_FULL_STEPS_PER_ROTATION * XYZ_MICROSTEPS / double(XYZ_BELT_PITCH) / double(XYZ_PULLEY_TEETH)) +/** + * Default Settings + * + * These settings can be reset by M502 + * + * Note that if EEPROM is enabled, saved values will override these. + */ + +/** + * Default Axis Steps Per Unit (steps/mm) + * Override with M92 + */ #define DEFAULT_AXIS_STEPS_PER_UNIT {XYZ_STEPS, XYZ_STEPS, XYZ_STEPS, 158} // default steps per unit for PowerWasp -#define DEFAULT_MAX_FEEDRATE {200, 200, 200, 25} // (mm/sec) -#define DEFAULT_MAX_ACCELERATION {9000,9000,9000,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for skeinforge 40+, for older versions raise them a lot. - -#define DEFAULT_ACCELERATION 2000 // X, Y, Z and E acceleration in mm/s^2 for printing moves -#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts -#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves - -// "Jerk" specifies the minimum speed change that requires acceleration. -// When changing speed and direction, if the difference is less than the -// value set here, it may happen instantaneously. -#define DEFAULT_XYJERK 20.0 // (mm/sec) -#define DEFAULT_ZJERK 20.0 // (mm/sec) -#define DEFAULT_EJERK 20.0 // (mm/sec) + +/** + * Default Max Feed Rate (mm/s) + * Override with M203 + */ +#define DEFAULT_MAX_FEEDRATE { 200, 200, 200, 25 } + +/** + * Default Max Acceleration (change/s) change = mm/s + * Override with M201 + * + * Maximum start speed for accelerated moves: { X, Y, Z, E } + */ +#define DEFAULT_MAX_ACCELERATION { 9000, 9000, 9000, 10000 } + +/** + * Default Acceleration (change/s) change = mm/s + * Override with M204 + * + * M204 P Acceleration + * M204 R Retract Acceleration + * M204 T Travel Acceleration + */ +#define DEFAULT_ACCELERATION 2000 // X, Y, Z and E acceleration for printing moves +#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration for retracts +#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves + +/** + * Defult Jerk (mm/s) + * + * "Jerk" specifies the minimum speed change that requires acceleration. + * When changing speed and direction, if the difference is less than the + * value set here, it may happen instantaneously. + */ +#define DEFAULT_XYJERK 20.0 +#define DEFAULT_ZJERK 20.0 +#define DEFAULT_EJERK 20.0 //=========================================================================== diff --git a/Marlin/example_configurations/makibox/Configuration.h b/Marlin/example_configurations/makibox/Configuration.h index dc44069f13..f1fc9b8b0f 100644 --- a/Marlin/example_configurations/makibox/Configuration.h +++ b/Marlin/example_configurations/makibox/Configuration.h @@ -358,8 +358,9 @@ #define EXTRUDE_MINTEMP 170 // This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH. +// Note that for Bowden Extruders a too-small value here may prevent loading. #define PREVENT_LENGTHY_EXTRUDE -#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) +#define EXTRUDE_MAXLENGTH 200 //=========================================================================== //======================== Thermal Runaway Protection ======================= @@ -439,20 +440,56 @@ //============================================================================= // @section motion -#define DEFAULT_AXIS_STEPS_PER_UNIT {400, 400, 400, 163} // default steps per unit for ***** MakiBox A6 ***** -#define DEFAULT_MAX_FEEDRATE {60, 60, 20, 45} // (mm/sec) -#define DEFAULT_MAX_ACCELERATION {2000,2000,30,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot. +/** + * Default Settings + * + * These settings can be reset by M502 + * + * Note that if EEPROM is enabled, saved values will override these. + */ + +/** + * Default Axis Steps Per Unit (steps/mm) + * Override with M92 + */ +#define DEFAULT_AXIS_STEPS_PER_UNIT { 400, 400, 400, 163 } // default steps per unit for ***** MakiBox A6 ***** + +/** + * Default Max Feed Rate (mm/s) + * Override with M203 + */ +#define DEFAULT_MAX_FEEDRATE { 60, 60, 20, 45 } -#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration in mm/s^2 for printing moves -#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts -#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves +/** + * Default Max Acceleration (change/s) change = mm/s + * Override with M201 + * + * Maximum start speed for accelerated moves: { X, Y, Z, E } + */ +#define DEFAULT_MAX_ACCELERATION { 2000, 2000, 30, 10000 } + +/** + * Default Acceleration (change/s) change = mm/s + * Override with M204 + * + * M204 P Acceleration + * M204 R Retract Acceleration + * M204 T Travel Acceleration + */ +#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration for printing moves +#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration for retracts +#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves -// "Jerk" specifies the minimum speed change that requires acceleration. -// When changing speed and direction, if the difference is less than the -// value set here, it may happen instantaneously. -#define DEFAULT_XYJERK 20.0 // (mm/sec) -#define DEFAULT_ZJERK 0.4 // (mm/sec) -#define DEFAULT_EJERK 5.0 // (mm/sec) +/** + * Defult Jerk (mm/s) + * + * "Jerk" specifies the minimum speed change that requires acceleration. + * When changing speed and direction, if the difference is less than the + * value set here, it may happen instantaneously. + */ +#define DEFAULT_XYJERK 20.0 +#define DEFAULT_ZJERK 0.4 +#define DEFAULT_EJERK 5.0 //=========================================================================== diff --git a/Marlin/example_configurations/makibox/Configuration_adv.h b/Marlin/example_configurations/makibox/Configuration_adv.h index 7e9d002f87..fc40866d60 100644 --- a/Marlin/example_configurations/makibox/Configuration_adv.h +++ b/Marlin/example_configurations/makibox/Configuration_adv.h @@ -389,7 +389,7 @@ // Number of channels available for I2C digipot, For Azteeg X3 Pro we have 8 #define DIGIPOT_I2C_NUM_CHANNELS 4 // actual motor currents in Amps, need as many here as DIGIPOT_I2C_NUM_CHANNELS -#define DIGIPOT_I2C_MOTOR_CURRENTS {1.7, 1.7, 1.7, 1.7} +#define DIGIPOT_I2C_MOTOR_CURRENTS { 1.7, 1.7, 1.7, 1.7 } //=========================================================================== //=============================Additional Features=========================== diff --git a/Marlin/example_configurations/tvrrug/Round2/Configuration.h b/Marlin/example_configurations/tvrrug/Round2/Configuration.h index df9f315699..c56cd6cbe2 100644 --- a/Marlin/example_configurations/tvrrug/Round2/Configuration.h +++ b/Marlin/example_configurations/tvrrug/Round2/Configuration.h @@ -345,8 +345,9 @@ #define EXTRUDE_MINTEMP 170 // This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH. +// Note that for Bowden Extruders a too-small value here may prevent loading. #define PREVENT_LENGTHY_EXTRUDE -#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) +#define EXTRUDE_MAXLENGTH 200 //=========================================================================== //======================== Thermal Runaway Protection ======================= @@ -426,24 +427,62 @@ //============================================================================= // @section motion +/** + * Default Settings + * + * These settings can be reset by M502 + * + * Note that if EEPROM is enabled, saved values will override these. + */ + +/** + * Default Axis Steps Per Unit (steps/mm) + * Override with M92 + */ +#define DEFAULT_AXIS_STEPS_PER_UNIT { 71.1, 71.1, 2560, 600 } // David TVRR + //#define DEFAULT_AXIS_STEPS_PER_UNIT {79.87, 79.87, 2566, 563,78} // Al's TVRR -//#define DEFAULT_AXIS_STEPS_PER_UNIT {81.26, 80.01, 2561, 599.14} // Michel TVRR old -//#define DEFAULT_AXIS_STEPS_PER_UNIT {71.1, 71.1, 2560, 739.65} // Michel TVRR -#define DEFAULT_AXIS_STEPS_PER_UNIT {71.1, 71.1, 2560, 600} // David TVRR -#define DEFAULT_MAX_FEEDRATE {500, 500, 5, 45} // (mm/sec) David TVRR -#define DEFAULT_MAX_ACCELERATION {9000,9000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot. +//#define DEFAULT_AXIS_STEPS_PER_UNIT { 81.26, 80.01, 2561, 599.14 } // Michel TVRR old +//#define DEFAULT_AXIS_STEPS_PER_UNIT { 71.1, 71.1, 2560, 739.65 } // Michel TVRR + +/** + * Default Max Feed Rate (mm/s) + * Override with M203 + */ +#define DEFAULT_MAX_FEEDRATE { 500, 500, 5, 45 } // David TVRR + +/** + * Default Max Acceleration (change/s) change = mm/s + * Override with M201 + * + * Maximum start speed for accelerated moves: { X, Y, Z, E } + */ +#define DEFAULT_MAX_ACCELERATION { 9000, 9000, 100, 10000 } /* MICHEL: This has an impact on the "ripples" in print walls */ -#define DEFAULT_ACCELERATION 500 // X, Y, Z and E acceleration in mm/s^2 for printing moves -#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts -#define DEFAULT_TRAVEL_ACCELERATION 500 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves - -// "Jerk" specifies the minimum speed change that requires acceleration. -// When changing speed and direction, if the difference is less than the -// value set here, it may happen instantaneously. -#define DEFAULT_XYJERK 20.0 // (mm/sec) -#define DEFAULT_ZJERK 0.4 // (mm/sec) -#define DEFAULT_EJERK 5.0 // (mm/sec) + +/** + * Default Acceleration (change/s) change = mm/s + * Override with M204 + * + * M204 P Acceleration + * M204 R Retract Acceleration + * M204 T Travel Acceleration + */ +#define DEFAULT_ACCELERATION 500 // X, Y, Z and E acceleration for printing moves +#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration for retracts +#define DEFAULT_TRAVEL_ACCELERATION 500 // X, Y, Z acceleration for travel (non printing) moves + +/** + * Defult Jerk (mm/s) + * + * "Jerk" specifies the minimum speed change that requires acceleration. + * When changing speed and direction, if the difference is less than the + * value set here, it may happen instantaneously. + */ +#define DEFAULT_XYJERK 20.0 +#define DEFAULT_ZJERK 0.4 +#define DEFAULT_EJERK 5.0 //=========================================================================== diff --git a/Marlin/pins_PRINTRBOARD_REVF.h b/Marlin/pins_PRINTRBOARD_REVF.h index 61b23fb4cd..1b49f8986a 100644 --- a/Marlin/pins_PRINTRBOARD_REVF.h +++ b/Marlin/pins_PRINTRBOARD_REVF.h @@ -83,7 +83,7 @@ // uncomment to enable an I2C based DAC like on the Printrboard REVF #define DAC_STEPPER_CURRENT // Number of channels available for DAC, For Printrboar REVF there are 4 -#define DAC_STEPPER_ORDER {3,2,1,0} +#define DAC_STEPPER_ORDER { 3, 2, 1, 0 } #define DAC_STEPPER_SENSE 0.11 #define DAC_STEPPER_ADDRESS 0 diff --git a/Marlin/pins_RIGIDBOARD_V2.h b/Marlin/pins_RIGIDBOARD_V2.h index 7aad12e9ac..4f0171ad20 100644 --- a/Marlin/pins_RIGIDBOARD_V2.h +++ b/Marlin/pins_RIGIDBOARD_V2.h @@ -32,7 +32,7 @@ // I2C based DAC like on the Printrboard REVF #define DAC_STEPPER_CURRENT // Channels available for DAC, For Rigidboard there are 4 -#define DAC_STEPPER_ORDER {0,1,2,3} +#define DAC_STEPPER_ORDER { 0, 1, 2, 3 } #define DAC_STEPPER_SENSE 0.11 #define DAC_STEPPER_ADDRESS 0