Merge pull request #11264 from teemuatlut/bf2_define_drivers

[2.0.x] Configure stepper drivers per axis
6 years ago · 4dfbae0e5c
116 changed files with 3546 additions and 5196 deletions
--- a/Marlin/Configuration.h
+++ b/Marlin/Configuration.h
@ -551,6 +551,29 @@
 #define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
 #define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.

+/**
+ * Specify Stepper Driver types
+ * The options are used to determine driver pulse timings as well as more advanced functionality.
+ * Stepper timing options can be overridden in Configuration_adv.h
+ *
+ * Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
+ *          TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
+ *          TMC26X,  TMC26X_STANDALONE,  TMC2660, TMC2660_STANDALONE,
+ *          TMC5130, TMC5130_STANDALONE
+ * :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
+ */
+#define X_DRIVER_TYPE  A4988
+#define Y_DRIVER_TYPE  A4988
+#define Z_DRIVER_TYPE  A4988
+#define X2_DRIVER_TYPE A4988
+#define Y2_DRIVER_TYPE A4988
+#define Z2_DRIVER_TYPE A4988
+#define E0_DRIVER_TYPE A4988
+#define E1_DRIVER_TYPE A4988
+#define E2_DRIVER_TYPE A4988
+#define E3_DRIVER_TYPE A4988
+#define E4_DRIVER_TYPE A4988
+
 // Enable this feature if all enabled endstop pins are interrupt-capable.
 // This will remove the need to poll the interrupt pins, saving many CPU cycles.
 //#define ENDSTOP_INTERRUPTS_FEATURE
--- a/Marlin/Configuration_adv.h
+++ b/Marlin/Configuration_adv.h
@ -837,15 +837,17 @@

 /**
 * Minimum delay after setting the stepper DIR (in ns)
- *    0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
- *   20 : Minimum for TMC2xxx drivers
- *  200 : Minimum for A4988 drivers
- *  500 : Minimum for LV8729 drivers (guess, no info in datasheet)
- *  650 : Minimum for DRV8825 drivers
- * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
- *15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *     0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
+ *    20 : Minimum for TMC2xxx drivers
+ *   200 : Minimum for A4988 drivers
+ *   500 : Minimum for LV8729 drivers (guess, no info in datasheet)
+ *   650 : Minimum for DRV8825 drivers
+ *  1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
+ * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_DIR_DELAY 0
+//#define MINIMUM_STEPPER_DIR_DELAY 650

 /**
 * Minimum stepper driver pulse width (in µs)
@ -855,8 +857,10 @@
 *   2 : Minimum for DRV8825 stepper drivers
 *   3 : Minimum for TB6600 stepper drivers
 *  30 : Minimum for TB6560 stepper drivers
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_PULSE 2
+//#define MINIMUM_STEPPER_PULSE 2

 /**
 * Maximum stepping rate (in Hz) the stepper driver allows
@ -867,8 +871,10 @@
 *  150000 : Maximum for TB6600 stepper driver
 *  130000 : Maximum for LV8729 stepper driver
 *   15000 : Maximum for TB6560 stepper driver
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MAXIMUM_STEPPER_RATE 250000
+//#define MAXIMUM_STEPPER_RATE 250000

 // @section temperature

@ -1036,23 +1042,12 @@
 // @section tmc

 /**
- * Enable this section if you have TMC26X motor drivers.
- * You will need to import the TMC26XStepper library into the Arduino IDE for this
- * (https://github.com/trinamic/TMC26XStepper.git)
+ * TMC26X Stepper Driver options
+ *
+ * The TMC26XStepper library is required for this stepper driver.
+ * https://github.com/trinamic/TMC26XStepper
 */
-//#define HAVE_TMC26X
-#if ENABLED(HAVE_TMC26X)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC26X
-  //#define X2_IS_TMC26X
-  //#define Y_IS_TMC26X
-  //#define Y2_IS_TMC26X
-  //#define Z_IS_TMC26X
-  //#define Z2_IS_TMC26X
-  //#define E0_IS_TMC26X
-  //#define E1_IS_TMC26X
-  //#define E2_IS_TMC26X
-  //#define E3_IS_TMC26X
-  //#define E4_IS_TMC26X
+#if HAS_DRIVER(TMC26X)

  #define X_MAX_CURRENT     1000 // in mA
  #define X_SENSE_RESISTOR    91 // in mOhms
@ -1098,62 +1093,29 @@
  #define E4_SENSE_RESISTOR   91
  #define E4_MICROSTEPS       16

-#endif
+#endif // TMC26X

 // @section tmc_smart

 /**
- * Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
- *
- * You'll also need the TMC2130Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2130Stepper).
- *
 * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
 * the hardware SPI interface on your board and define the required CS pins
 * in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
 * You may also use software SPI if you wish to use general purpose IO pins.
- */
-//#define HAVE_TMC2130
-#if ENABLED(HAVE_TMC2130)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2130
-  //#define X2_IS_TMC2130
-  //#define Y_IS_TMC2130
-  //#define Y2_IS_TMC2130
-  //#define Z_IS_TMC2130
-  //#define Z2_IS_TMC2130
-  //#define E0_IS_TMC2130
-  //#define E1_IS_TMC2130
-  //#define E2_IS_TMC2130
-  //#define E3_IS_TMC2130
-  //#define E4_IS_TMC2130
-#endif
-
-/**
- * Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
- * Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
+ *
+ * The TMC2130Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2130Stepper
+ *
+ * To use TMC2208 stepper UART-configurable stepper drivers
+ * connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
 * To use the reading capabilities, also connect #_SERIAL_RX_PIN
 * to PDN_UART without a resistor.
 * The drivers can also be used with hardware serial.
 *
- * You'll also need the TMC2208Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2208Stepper).
+ * The TMC2208Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2208Stepper
 */
-//#define HAVE_TMC2208
-#if ENABLED(HAVE_TMC2208)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2208
-  //#define X2_IS_TMC2208
-  //#define Y_IS_TMC2208
-  //#define Y2_IS_TMC2208
-  //#define Z_IS_TMC2208
-  //#define Z2_IS_TMC2208
-  //#define E0_IS_TMC2208
-  //#define E1_IS_TMC2208
-  //#define E2_IS_TMC2208
-  //#define E3_IS_TMC2208
-  //#define E4_IS_TMC2208
-#endif
-
-#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
+#if HAS_TRINAMIC

  #define R_SENSE           0.11  // R_sense resistor for SilentStepStick2130
  #define HOLD_MULTIPLIER    0.5  // Scales down the holding current from run current
@ -1308,25 +1270,12 @@
 // @section L6470

 /**
- * Enable this section if you have L6470 motor drivers.
- * You need to import the L6470 library into the Arduino IDE for this.
- * (https://github.com/ameyer/Arduino-L6470)
+ * L6470 Stepper Driver options
+ *
+ * The Arduino-L6470 library is required for this stepper driver.
+ * https://github.com/ameyer/Arduino-L6470
 */
-
-//#define HAVE_L6470DRIVER
-#if ENABLED(HAVE_L6470DRIVER)
-
-  //#define X_IS_L6470
-  //#define X2_IS_L6470
-  //#define Y_IS_L6470
-  //#define Y2_IS_L6470
-  //#define Z_IS_L6470
-  //#define Z2_IS_L6470
-  //#define E0_IS_L6470
-  //#define E1_IS_L6470
-  //#define E2_IS_L6470
-  //#define E3_IS_L6470
-  //#define E4_IS_L6470
+#if HAS_DRIVER(L6470)

  #define X_MICROSTEPS      16 // number of microsteps
  #define X_OVERCURRENT   2000 // maxc current in mA. If the current goes over this value, the driver will switch off
@ -1372,7 +1321,7 @@
  #define E4_OVERCURRENT  2000
  #define E4_STALLCURRENT 1500

-#endif
+#endif // L6470

 /**
 * TWI/I2C BUS
--- a/Marlin/src/HAL/HAL_AVR/SanityCheck.h
+++ b/Marlin/src/HAL/HAL_AVR/SanityCheck.h
@ -99,7 +99,7 @@
 /**
 * TMC2208 software UART and ENDSTOP_INTERRUPTS both use pin change interrupts (PCI)
 */
-#if ENABLED(HAVE_TMC2208) && ENABLED(ENDSTOP_INTERRUPTS_FEATURE) && !( \
+#if HAS_DRIVER(TMC2208) && ENABLED(ENDSTOP_INTERRUPTS_FEATURE) && !( \
       defined(X_HARDWARE_SERIAL ) \
    || defined(X2_HARDWARE_SERIAL) \
    || defined(Y_HARDWARE_SERIAL ) \
--- a/Marlin/src/HAL/HAL_DUE/SanityCheck.h
+++ b/Marlin/src/HAL/HAL_DUE/SanityCheck.h
@ -41,7 +41,7 @@
 */
 #define _IS_HW_SPI(P) (defined(TMC_SW_##P) && (TMC_SW_##P == MOSI_PIN || TMC_SW_##P == MISO_PIN || TMC_SW_##P == SCK_PIN))

-#if ENABLED(SDSUPPORT) && ENABLED(HAVE_TMC2130)
+#if ENABLED(SDSUPPORT) && HAS_DRIVER(TMC2130)
  #if ENABLED(TMC_USE_SW_SPI)
    #if DISABLED(DUE_SOFTWARE_SPI) && (_IS_HW_SPI(MOSI) || _IS_HW_SPI(MISO) || _IS_HW_SPI(SCK))
      #error "DUE hardware SPI is required but is incompatible with TMC2130 software SPI. Either disable TMC_USE_SW_SPI or use separate pins for the two SPIs."
--- a/Marlin/src/HAL/HAL_LPC1768/SanityCheck.h
+++ b/Marlin/src/HAL/HAL_LPC1768/SanityCheck.h
@ -66,7 +66,7 @@
  #endif
 #endif // SPINDLE_LASER_ENABLE

-#if ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) && ENABLED(HAVE_TMC2130) && DISABLED(TMC_USE_SW_SPI) \
+#if ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) && HAS_DRIVER(TMC2130) && DISABLED(TMC_USE_SW_SPI) \
    && (MB(RAMPS_14_RE_ARM_EFB) \
    ||  MB(RAMPS_14_RE_ARM_EEB) \
    ||  MB(RAMPS_14_RE_ARM_EFF) \
--- a/Marlin/src/Marlin.cpp
+++ b/Marlin/src/Marlin.cpp
@ -712,10 +712,10 @@ void setup() {
  SERIAL_PROTOCOLLNPGM("start");
  SERIAL_ECHO_START();

-  #if ENABLED(HAVE_TMC2130)
+  #if HAS_DRIVER(TMC2130)
    tmc_init_cs_pins();
  #endif
-  #if ENABLED(HAVE_TMC2208)
+  #if HAS_DRIVER(TMC2208)
    tmc2208_serial_begin();
  #endif

--- a/Marlin/src/config/default/Configuration.h
+++ b/Marlin/src/config/default/Configuration.h
@ -551,6 +551,29 @@
 #define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
 #define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.

+/**
+ * Specify Stepper Driver types
+ * The options are used to determine driver pulse timings as well as more advanced functionality.
+ * Stepper timing options can be overridden in Configuration_adv.h
+ *
+ * Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
+ *          TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
+ *          TMC26X,  TMC26X_STANDALONE,  TMC2660, TMC2660_STANDALONE,
+ *          TMC5130, TMC5130_STANDALONE
+ * :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
+ */
+#define X_DRIVER_TYPE  A4988
+#define Y_DRIVER_TYPE  A4988
+#define Z_DRIVER_TYPE  A4988
+#define X2_DRIVER_TYPE A4988
+#define Y2_DRIVER_TYPE A4988
+#define Z2_DRIVER_TYPE A4988
+#define E0_DRIVER_TYPE A4988
+#define E1_DRIVER_TYPE A4988
+#define E2_DRIVER_TYPE A4988
+#define E3_DRIVER_TYPE A4988
+#define E4_DRIVER_TYPE A4988
+
 // Enable this feature if all enabled endstop pins are interrupt-capable.
 // This will remove the need to poll the interrupt pins, saving many CPU cycles.
 //#define ENDSTOP_INTERRUPTS_FEATURE
--- a/Marlin/src/config/default/Configuration_adv.h
+++ b/Marlin/src/config/default/Configuration_adv.h
@ -837,15 +837,17 @@

 /**
 * Minimum delay after setting the stepper DIR (in ns)
- *    0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
- *   20 : Minimum for TMC2xxx drivers
- *  200 : Minimum for A4988 drivers
- *  500 : Minimum for LV8729 drivers (guess, no info in datasheet)
- *  650 : Minimum for DRV8825 drivers
- * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
- *15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *     0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
+ *    20 : Minimum for TMC2xxx drivers
+ *   200 : Minimum for A4988 drivers
+ *   500 : Minimum for LV8729 drivers (guess, no info in datasheet)
+ *   650 : Minimum for DRV8825 drivers
+ *  1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
+ * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_DIR_DELAY 0
+//#define MINIMUM_STEPPER_DIR_DELAY 650

 /**
 * Minimum stepper driver pulse width (in µs)
@ -855,8 +857,10 @@
 *   2 : Minimum for DRV8825 stepper drivers
 *   3 : Minimum for TB6600 stepper drivers
 *  30 : Minimum for TB6560 stepper drivers
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_PULSE 2
+//#define MINIMUM_STEPPER_PULSE 2

 /**
 * Maximum stepping rate (in Hz) the stepper driver allows
@ -867,8 +871,10 @@
 *  150000 : Maximum for TB6600 stepper driver
 *  130000 : Maximum for LV8729 stepper driver
 *   15000 : Maximum for TB6560 stepper driver
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MAXIMUM_STEPPER_RATE 250000
+//#define MAXIMUM_STEPPER_RATE 250000

 // @section temperature

@ -1036,23 +1042,12 @@
 // @section tmc

 /**
- * Enable this section if you have TMC26X motor drivers.
- * You will need to import the TMC26XStepper library into the Arduino IDE for this
- * (https://github.com/trinamic/TMC26XStepper.git)
+ * TMC26X Stepper Driver options
+ *
+ * The TMC26XStepper library is required for this stepper driver.
+ * https://github.com/trinamic/TMC26XStepper
 */
-//#define HAVE_TMC26X
-#if ENABLED(HAVE_TMC26X)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC26X
-  //#define X2_IS_TMC26X
-  //#define Y_IS_TMC26X
-  //#define Y2_IS_TMC26X
-  //#define Z_IS_TMC26X
-  //#define Z2_IS_TMC26X
-  //#define E0_IS_TMC26X
-  //#define E1_IS_TMC26X
-  //#define E2_IS_TMC26X
-  //#define E3_IS_TMC26X
-  //#define E4_IS_TMC26X
+#if HAS_DRIVER(TMC26X)

  #define X_MAX_CURRENT     1000 // in mA
  #define X_SENSE_RESISTOR    91 // in mOhms
@ -1098,62 +1093,29 @@
  #define E4_SENSE_RESISTOR   91
  #define E4_MICROSTEPS       16

-#endif
+#endif // TMC26X

 // @section tmc_smart

 /**
- * Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
- *
- * You'll also need the TMC2130Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2130Stepper).
- *
 * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
 * the hardware SPI interface on your board and define the required CS pins
 * in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
 * You may also use software SPI if you wish to use general purpose IO pins.
- */
-//#define HAVE_TMC2130
-#if ENABLED(HAVE_TMC2130)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2130
-  //#define X2_IS_TMC2130
-  //#define Y_IS_TMC2130
-  //#define Y2_IS_TMC2130
-  //#define Z_IS_TMC2130
-  //#define Z2_IS_TMC2130
-  //#define E0_IS_TMC2130
-  //#define E1_IS_TMC2130
-  //#define E2_IS_TMC2130
-  //#define E3_IS_TMC2130
-  //#define E4_IS_TMC2130
-#endif
-
-/**
- * Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
- * Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
+ *
+ * The TMC2130Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2130Stepper
+ *
+ * To use TMC2208 stepper UART-configurable stepper drivers
+ * connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
 * To use the reading capabilities, also connect #_SERIAL_RX_PIN
 * to PDN_UART without a resistor.
 * The drivers can also be used with hardware serial.
 *
- * You'll also need the TMC2208Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2208Stepper).
+ * The TMC2208Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2208Stepper
 */
-//#define HAVE_TMC2208
-#if ENABLED(HAVE_TMC2208)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2208
-  //#define X2_IS_TMC2208
-  //#define Y_IS_TMC2208
-  //#define Y2_IS_TMC2208
-  //#define Z_IS_TMC2208
-  //#define Z2_IS_TMC2208
-  //#define E0_IS_TMC2208
-  //#define E1_IS_TMC2208
-  //#define E2_IS_TMC2208
-  //#define E3_IS_TMC2208
-  //#define E4_IS_TMC2208
-#endif
-
-#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
+#if HAS_TRINAMIC

  #define R_SENSE           0.11  // R_sense resistor for SilentStepStick2130
  #define HOLD_MULTIPLIER    0.5  // Scales down the holding current from run current
@ -1308,25 +1270,12 @@
 // @section L6470

 /**
- * Enable this section if you have L6470 motor drivers.
- * You need to import the L6470 library into the Arduino IDE for this.
- * (https://github.com/ameyer/Arduino-L6470)
+ * L6470 Stepper Driver options
+ *
+ * The Arduino-L6470 library is required for this stepper driver.
+ * https://github.com/ameyer/Arduino-L6470
 */
-
-//#define HAVE_L6470DRIVER
-#if ENABLED(HAVE_L6470DRIVER)
-
-  //#define X_IS_L6470
-  //#define X2_IS_L6470
-  //#define Y_IS_L6470
-  //#define Y2_IS_L6470
-  //#define Z_IS_L6470
-  //#define Z2_IS_L6470
-  //#define E0_IS_L6470
-  //#define E1_IS_L6470
-  //#define E2_IS_L6470
-  //#define E3_IS_L6470
-  //#define E4_IS_L6470
+#if HAS_DRIVER(L6470)

  #define X_MICROSTEPS      16 // number of microsteps
  #define X_OVERCURRENT   2000 // maxc current in mA. If the current goes over this value, the driver will switch off
@ -1372,7 +1321,7 @@
  #define E4_OVERCURRENT  2000
  #define E4_STALLCURRENT 1500

-#endif
+#endif // L6470

 /**
 * TWI/I2C BUS
--- a/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration_adv.h
+++ b/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration_adv.h
@ -837,15 +837,17 @@

 /**
 * Minimum delay after setting the stepper DIR (in ns)
- *    0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
- *   20 : Minimum for TMC2xxx drivers
- *  200 : Minimum for A4988 drivers
- *  500 : Minimum for LV8729 drivers (guess, no info in datasheet)
- *  650 : Minimum for DRV8825 drivers
- * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
- *15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *     0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
+ *    20 : Minimum for TMC2xxx drivers
+ *   200 : Minimum for A4988 drivers
+ *   500 : Minimum for LV8729 drivers (guess, no info in datasheet)
+ *   650 : Minimum for DRV8825 drivers
+ *  1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
+ * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_DIR_DELAY 0
+//#define MINIMUM_STEPPER_DIR_DELAY 650

 /**
 * Minimum stepper driver pulse width (in µs)
@ -855,8 +857,10 @@
 *   2 : Minimum for DRV8825 stepper drivers
 *   3 : Minimum for TB6600 stepper drivers
 *  30 : Minimum for TB6560 stepper drivers
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_PULSE 2
+//#define MINIMUM_STEPPER_PULSE 2

 /**
 * Maximum stepping rate (in Hz) the stepper driver allows
@ -867,8 +871,10 @@
 *  150000 : Maximum for TB6600 stepper driver
 *  130000 : Maximum for LV8729 stepper driver
 *   15000 : Maximum for TB6560 stepper driver
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MAXIMUM_STEPPER_RATE 250000
+//#define MAXIMUM_STEPPER_RATE 250000

 // @section temperature

@ -1036,23 +1042,12 @@
 // @section tmc

 /**
- * Enable this section if you have TMC26X motor drivers.
- * You will need to import the TMC26XStepper library into the Arduino IDE for this
- * (https://github.com/trinamic/TMC26XStepper.git)
+ * TMC26X Stepper Driver options
+ *
+ * The TMC26XStepper library is required for this stepper driver.
+ * https://github.com/trinamic/TMC26XStepper
 */
-//#define HAVE_TMC26X
-#if ENABLED(HAVE_TMC26X)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC26X
-  //#define X2_IS_TMC26X
-  //#define Y_IS_TMC26X
-  //#define Y2_IS_TMC26X
-  //#define Z_IS_TMC26X
-  //#define Z2_IS_TMC26X
-  //#define E0_IS_TMC26X
-  //#define E1_IS_TMC26X
-  //#define E2_IS_TMC26X
-  //#define E3_IS_TMC26X
-  //#define E4_IS_TMC26X
+#if HAS_DRIVER(TMC26X)

  #define X_MAX_CURRENT     1000 // in mA
  #define X_SENSE_RESISTOR    91 // in mOhms
@ -1098,62 +1093,29 @@
  #define E4_SENSE_RESISTOR   91
  #define E4_MICROSTEPS       16

-#endif
+#endif // TMC26X

 // @section tmc_smart

 /**
- * Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
- *
- * You'll also need the TMC2130Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2130Stepper).
- *
 * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
 * the hardware SPI interface on your board and define the required CS pins
 * in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
 * You may also use software SPI if you wish to use general purpose IO pins.
- */
-//#define HAVE_TMC2130
-#if ENABLED(HAVE_TMC2130)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2130
-  //#define X2_IS_TMC2130
-  //#define Y_IS_TMC2130
-  //#define Y2_IS_TMC2130
-  //#define Z_IS_TMC2130
-  //#define Z2_IS_TMC2130
-  //#define E0_IS_TMC2130
-  //#define E1_IS_TMC2130
-  //#define E2_IS_TMC2130
-  //#define E3_IS_TMC2130
-  //#define E4_IS_TMC2130
-#endif
-
-/**
- * Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
- * Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
+ *
+ * The TMC2130Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2130Stepper
+ *
+ * To use TMC2208 stepper UART-configurable stepper drivers
+ * connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
 * To use the reading capabilities, also connect #_SERIAL_RX_PIN
 * to PDN_UART without a resistor.
 * The drivers can also be used with hardware serial.
 *
- * You'll also need the TMC2208Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2208Stepper).
+ * The TMC2208Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2208Stepper
 */
-//#define HAVE_TMC2208
-#if ENABLED(HAVE_TMC2208)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2208
-  //#define X2_IS_TMC2208
-  //#define Y_IS_TMC2208
-  //#define Y2_IS_TMC2208
-  //#define Z_IS_TMC2208
-  //#define Z2_IS_TMC2208
-  //#define E0_IS_TMC2208
-  //#define E1_IS_TMC2208
-  //#define E2_IS_TMC2208
-  //#define E3_IS_TMC2208
-  //#define E4_IS_TMC2208
-#endif
-
-#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
+#if HAS_TRINAMIC

  #define R_SENSE           0.11  // R_sense resistor for SilentStepStick2130
  #define HOLD_MULTIPLIER    0.5  // Scales down the holding current from run current
@ -1308,25 +1270,12 @@
 // @section L6470

 /**
- * Enable this section if you have L6470 motor drivers.
- * You need to import the L6470 library into the Arduino IDE for this.
- * (https://github.com/ameyer/Arduino-L6470)
+ * L6470 Stepper Driver options
+ *
+ * The Arduino-L6470 library is required for this stepper driver.
+ * https://github.com/ameyer/Arduino-L6470
 */
-
-//#define HAVE_L6470DRIVER
-#if ENABLED(HAVE_L6470DRIVER)
-
-  //#define X_IS_L6470
-  //#define X2_IS_L6470
-  //#define Y_IS_L6470
-  //#define Y2_IS_L6470
-  //#define Z_IS_L6470
-  //#define Z2_IS_L6470
-  //#define E0_IS_L6470
-  //#define E1_IS_L6470
-  //#define E2_IS_L6470
-  //#define E3_IS_L6470
-  //#define E4_IS_L6470
+#if HAS_DRIVER(L6470)

  #define X_MICROSTEPS      16 // number of microsteps
  #define X_OVERCURRENT   2000 // maxc current in mA. If the current goes over this value, the driver will switch off
@ -1372,7 +1321,7 @@
  #define E4_OVERCURRENT  2000
  #define E4_STALLCURRENT 1500

-#endif
+#endif // L6470

 /**
 * TWI/I2C BUS
--- a/Marlin/src/config/examples/AliExpress/CL-260/Configuration.h
+++ b/Marlin/src/config/examples/AliExpress/CL-260/Configuration.h
@ -551,6 +551,29 @@
 #define Z_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
 #define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.

+/**
+ * Specify Stepper Driver types
+ * The options are used to determine driver pulse timings as well as more advanced functionality.
+ * Stepper timing options can be overridden in Configuration_adv.h
+ *
+ * Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
+ *          TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
+ *          TMC26X,  TMC26X_STANDALONE,  TMC2660, TMC2660_STANDALONE,
+ *          TMC5130, TMC5130_STANDALONE
+ * :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
+ */
+#define X_DRIVER_TYPE  A4988
+#define Y_DRIVER_TYPE  A4988
+#define Z_DRIVER_TYPE  A4988
+#define X2_DRIVER_TYPE A4988
+#define Y2_DRIVER_TYPE A4988
+#define Z2_DRIVER_TYPE A4988
+#define E0_DRIVER_TYPE A4988
+#define E1_DRIVER_TYPE A4988
+#define E2_DRIVER_TYPE A4988
+#define E3_DRIVER_TYPE A4988
+#define E4_DRIVER_TYPE A4988
+
 // Enable this feature if all enabled endstop pins are interrupt-capable.
 // This will remove the need to poll the interrupt pins, saving many CPU cycles.
 //#define ENDSTOP_INTERRUPTS_FEATURE
--- a/Marlin/src/config/examples/Anet/A6/Configuration.h
+++ b/Marlin/src/config/examples/Anet/A6/Configuration.h
@ -571,6 +571,29 @@
 #define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
 #define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.

+/**
+ * Specify Stepper Driver types
+ * The options are used to determine driver pulse timings as well as more advanced functionality.
+ * Stepper timing options can be overridden in Configuration_adv.h
+ *
+ * Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
+ *          TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
+ *          TMC26X,  TMC26X_STANDALONE,  TMC2660, TMC2660_STANDALONE,
+ *          TMC5130, TMC5130_STANDALONE
+ * :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
+ */
+#define X_DRIVER_TYPE  A4988
+#define Y_DRIVER_TYPE  A4988
+#define Z_DRIVER_TYPE  A4988
+#define X2_DRIVER_TYPE A4988
+#define Y2_DRIVER_TYPE A4988
+#define Z2_DRIVER_TYPE A4988
+#define E0_DRIVER_TYPE A4988
+#define E1_DRIVER_TYPE A4988
+#define E2_DRIVER_TYPE A4988
+#define E3_DRIVER_TYPE A4988
+#define E4_DRIVER_TYPE A4988
+
 // Enable this feature if all enabled endstop pins are interrupt-capable.
 // This will remove the need to poll the interrupt pins, saving many CPU cycles.
 #define ENDSTOP_INTERRUPTS_FEATURE
--- a/Marlin/src/config/examples/Anet/A6/Configuration_adv.h
+++ b/Marlin/src/config/examples/Anet/A6/Configuration_adv.h
@ -837,15 +837,17 @@

 /**
 * Minimum delay after setting the stepper DIR (in ns)
- *    0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
- *   20 : Minimum for TMC2xxx drivers
- *  200 : Minimum for A4988 drivers
- *  500 : Minimum for LV8729 drivers (guess, no info in datasheet)
- *  650 : Minimum for DRV8825 drivers
- * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
- *15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *     0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
+ *    20 : Minimum for TMC2xxx drivers
+ *   200 : Minimum for A4988 drivers
+ *   500 : Minimum for LV8729 drivers (guess, no info in datasheet)
+ *   650 : Minimum for DRV8825 drivers
+ *  1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
+ * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_DIR_DELAY 0
+//#define MINIMUM_STEPPER_DIR_DELAY 650

 /**
 * Minimum stepper driver pulse width (in µs)
@ -855,8 +857,10 @@
 *   2 : Minimum for DRV8825 stepper drivers
 *   3 : Minimum for TB6600 stepper drivers
 *  30 : Minimum for TB6560 stepper drivers
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_PULSE 2
+//#define MINIMUM_STEPPER_PULSE 2

 /**
 * Maximum stepping rate (in Hz) the stepper driver allows
@ -867,8 +871,10 @@
 *  150000 : Maximum for TB6600 stepper driver
 *  130000 : Maximum for LV8729 stepper driver
 *   15000 : Maximum for TB6560 stepper driver
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MAXIMUM_STEPPER_RATE 250000
+//#define MAXIMUM_STEPPER_RATE 250000

 // @section temperature

@ -1036,23 +1042,12 @@
 // @section tmc

 /**
- * Enable this section if you have TMC26X motor drivers.
- * You will need to import the TMC26XStepper library into the Arduino IDE for this
- * (https://github.com/trinamic/TMC26XStepper.git)
+ * TMC26X Stepper Driver options
+ *
+ * The TMC26XStepper library is required for this stepper driver.
+ * https://github.com/trinamic/TMC26XStepper
 */
-//#define HAVE_TMC26X
-#if ENABLED(HAVE_TMC26X)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC26X
-  //#define X2_IS_TMC26X
-  //#define Y_IS_TMC26X
-  //#define Y2_IS_TMC26X
-  //#define Z_IS_TMC26X
-  //#define Z2_IS_TMC26X
-  //#define E0_IS_TMC26X
-  //#define E1_IS_TMC26X
-  //#define E2_IS_TMC26X
-  //#define E3_IS_TMC26X
-  //#define E4_IS_TMC26X
+#if HAS_DRIVER(TMC26X)

  #define X_MAX_CURRENT     1000 // in mA
  #define X_SENSE_RESISTOR    91 // in mOhms
@ -1098,62 +1093,29 @@
  #define E4_SENSE_RESISTOR   91
  #define E4_MICROSTEPS       16

-#endif
+#endif // TMC26X

 // @section tmc_smart

 /**
- * Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
- *
- * You'll also need the TMC2130Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2130Stepper).
- *
 * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
 * the hardware SPI interface on your board and define the required CS pins
 * in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
 * You may also use software SPI if you wish to use general purpose IO pins.
- */
-//#define HAVE_TMC2130
-#if ENABLED(HAVE_TMC2130)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2130
-  //#define X2_IS_TMC2130
-  //#define Y_IS_TMC2130
-  //#define Y2_IS_TMC2130
-  //#define Z_IS_TMC2130
-  //#define Z2_IS_TMC2130
-  //#define E0_IS_TMC2130
-  //#define E1_IS_TMC2130
-  //#define E2_IS_TMC2130
-  //#define E3_IS_TMC2130
-  //#define E4_IS_TMC2130
-#endif
-
-/**
- * Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
- * Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
+ *
+ * The TMC2130Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2130Stepper
+ *
+ * To use TMC2208 stepper UART-configurable stepper drivers
+ * connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
 * To use the reading capabilities, also connect #_SERIAL_RX_PIN
 * to PDN_UART without a resistor.
 * The drivers can also be used with hardware serial.
 *
- * You'll also need the TMC2208Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2208Stepper).
+ * The TMC2208Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2208Stepper
 */
-//#define HAVE_TMC2208
-#if ENABLED(HAVE_TMC2208)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2208
-  //#define X2_IS_TMC2208
-  //#define Y_IS_TMC2208
-  //#define Y2_IS_TMC2208
-  //#define Z_IS_TMC2208
-  //#define Z2_IS_TMC2208
-  //#define E0_IS_TMC2208
-  //#define E1_IS_TMC2208
-  //#define E2_IS_TMC2208
-  //#define E3_IS_TMC2208
-  //#define E4_IS_TMC2208
-#endif
-
-#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
+#if HAS_TRINAMIC

  #define R_SENSE           0.11  // R_sense resistor for SilentStepStick2130
  #define HOLD_MULTIPLIER    0.5  // Scales down the holding current from run current
@ -1308,25 +1270,12 @@
 // @section L6470

 /**
- * Enable this section if you have L6470 motor drivers.
- * You need to import the L6470 library into the Arduino IDE for this.
- * (https://github.com/ameyer/Arduino-L6470)
+ * L6470 Stepper Driver options
+ *
+ * The Arduino-L6470 library is required for this stepper driver.
+ * https://github.com/ameyer/Arduino-L6470
 */
-
-//#define HAVE_L6470DRIVER
-#if ENABLED(HAVE_L6470DRIVER)
-
-  //#define X_IS_L6470
-  //#define X2_IS_L6470
-  //#define Y_IS_L6470
-  //#define Y2_IS_L6470
-  //#define Z_IS_L6470
-  //#define Z2_IS_L6470
-  //#define E0_IS_L6470
-  //#define E1_IS_L6470
-  //#define E2_IS_L6470
-  //#define E3_IS_L6470
-  //#define E4_IS_L6470
+#if HAS_DRIVER(L6470)

  #define X_MICROSTEPS      16 // number of microsteps
  #define X_OVERCURRENT   2000 // maxc current in mA. If the current goes over this value, the driver will switch off
@ -1372,7 +1321,7 @@
  #define E4_OVERCURRENT  2000
  #define E4_STALLCURRENT 1500

-#endif
+#endif // L6470

 /**
 * TWI/I2C BUS
--- a/Marlin/src/config/examples/Anet/A8/Configuration_adv.h
+++ b/Marlin/src/config/examples/Anet/A8/Configuration_adv.h
@ -837,15 +837,17 @@

 /**
 * Minimum delay after setting the stepper DIR (in ns)
- *    0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
- *   20 : Minimum for TMC2xxx drivers
- *  200 : Minimum for A4988 drivers
- *  500 : Minimum for LV8729 drivers (guess, no info in datasheet)
- *  650 : Minimum for DRV8825 drivers
- * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
- *15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *     0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
+ *    20 : Minimum for TMC2xxx drivers
+ *   200 : Minimum for A4988 drivers
+ *   500 : Minimum for LV8729 drivers (guess, no info in datasheet)
+ *   650 : Minimum for DRV8825 drivers
+ *  1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
+ * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_DIR_DELAY 0
+//#define MINIMUM_STEPPER_DIR_DELAY 650

 /**
 * Minimum stepper driver pulse width (in µs)
@ -855,8 +857,10 @@
 *   2 : Minimum for DRV8825 stepper drivers
 *   3 : Minimum for TB6600 stepper drivers
 *  30 : Minimum for TB6560 stepper drivers
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_PULSE 2
+//#define MINIMUM_STEPPER_PULSE 2

 /**
 * Maximum stepping rate (in Hz) the stepper driver allows
@ -867,8 +871,10 @@
 *  150000 : Maximum for TB6600 stepper driver
 *  130000 : Maximum for LV8729 stepper driver
 *   15000 : Maximum for TB6560 stepper driver
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MAXIMUM_STEPPER_RATE 250000
+//#define MAXIMUM_STEPPER_RATE 250000

 // @section temperature

@ -1036,23 +1042,12 @@
 // @section tmc

 /**
- * Enable this section if you have TMC26X motor drivers.
- * You will need to import the TMC26XStepper library into the Arduino IDE for this
- * (https://github.com/trinamic/TMC26XStepper.git)
+ * TMC26X Stepper Driver options
+ *
+ * The TMC26XStepper library is required for this stepper driver.
+ * https://github.com/trinamic/TMC26XStepper
 */
-//#define HAVE_TMC26X
-#if ENABLED(HAVE_TMC26X)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC26X
-  //#define X2_IS_TMC26X
-  //#define Y_IS_TMC26X
-  //#define Y2_IS_TMC26X
-  //#define Z_IS_TMC26X
-  //#define Z2_IS_TMC26X
-  //#define E0_IS_TMC26X
-  //#define E1_IS_TMC26X
-  //#define E2_IS_TMC26X
-  //#define E3_IS_TMC26X
-  //#define E4_IS_TMC26X
+#if HAS_DRIVER(TMC26X)

  #define X_MAX_CURRENT     1000 // in mA
  #define X_SENSE_RESISTOR    91 // in mOhms
@ -1098,62 +1093,29 @@
  #define E4_SENSE_RESISTOR   91
  #define E4_MICROSTEPS       16

-#endif
+#endif // TMC26X

 // @section tmc_smart

 /**
- * Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
- *
- * You'll also need the TMC2130Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2130Stepper).
- *
 * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
 * the hardware SPI interface on your board and define the required CS pins
 * in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
 * You may also use software SPI if you wish to use general purpose IO pins.
- */
-//#define HAVE_TMC2130
-#if ENABLED(HAVE_TMC2130)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2130
-  //#define X2_IS_TMC2130
-  //#define Y_IS_TMC2130
-  //#define Y2_IS_TMC2130
-  //#define Z_IS_TMC2130
-  //#define Z2_IS_TMC2130
-  //#define E0_IS_TMC2130
-  //#define E1_IS_TMC2130
-  //#define E2_IS_TMC2130
-  //#define E3_IS_TMC2130
-  //#define E4_IS_TMC2130
-#endif
-
-/**
- * Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
- * Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
+ *
+ * The TMC2130Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2130Stepper
+ *
+ * To use TMC2208 stepper UART-configurable stepper drivers
+ * connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
 * To use the reading capabilities, also connect #_SERIAL_RX_PIN
 * to PDN_UART without a resistor.
 * The drivers can also be used with hardware serial.
 *
- * You'll also need the TMC2208Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2208Stepper).
+ * The TMC2208Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2208Stepper
 */
-//#define HAVE_TMC2208
-#if ENABLED(HAVE_TMC2208)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2208
-  //#define X2_IS_TMC2208
-  //#define Y_IS_TMC2208
-  //#define Y2_IS_TMC2208
-  //#define Z_IS_TMC2208
-  //#define Z2_IS_TMC2208
-  //#define E0_IS_TMC2208
-  //#define E1_IS_TMC2208
-  //#define E2_IS_TMC2208
-  //#define E3_IS_TMC2208
-  //#define E4_IS_TMC2208
-#endif
-
-#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
+#if HAS_TRINAMIC

  #define R_SENSE           0.11  // R_sense resistor for SilentStepStick2130
  #define HOLD_MULTIPLIER    0.5  // Scales down the holding current from run current
@ -1308,25 +1270,12 @@
 // @section L6470

 /**
- * Enable this section if you have L6470 motor drivers.
- * You need to import the L6470 library into the Arduino IDE for this.
- * (https://github.com/ameyer/Arduino-L6470)
+ * L6470 Stepper Driver options
+ *
+ * The Arduino-L6470 library is required for this stepper driver.
+ * https://github.com/ameyer/Arduino-L6470
 */
-
-//#define HAVE_L6470DRIVER
-#if ENABLED(HAVE_L6470DRIVER)
-
-  //#define X_IS_L6470
-  //#define X2_IS_L6470
-  //#define Y_IS_L6470
-  //#define Y2_IS_L6470
-  //#define Z_IS_L6470
-  //#define Z2_IS_L6470
-  //#define E0_IS_L6470
-  //#define E1_IS_L6470
-  //#define E2_IS_L6470
-  //#define E3_IS_L6470
-  //#define E4_IS_L6470
+#if HAS_DRIVER(L6470)

  #define X_MICROSTEPS      16 // number of microsteps
  #define X_OVERCURRENT   2000 // maxc current in mA. If the current goes over this value, the driver will switch off
@ -1372,7 +1321,7 @@
  #define E4_OVERCURRENT  2000
  #define E4_STALLCURRENT 1500

-#endif
+#endif // L6470

 /**
 * TWI/I2C BUS
--- a/Marlin/src/config/examples/Azteeg/X5GT/Configuration.h
+++ b/Marlin/src/config/examples/Azteeg/X5GT/Configuration.h
@ -551,6 +551,29 @@
 #define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
 #define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.

+/**
+ * Specify Stepper Driver types
+ * The options are used to determine driver pulse timings as well as more advanced functionality.
+ * Stepper timing options can be overridden in Configuration_adv.h
+ *
+ * Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
+ *          TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
+ *          TMC26X,  TMC26X_STANDALONE,  TMC2660, TMC2660_STANDALONE,
+ *          TMC5130, TMC5130_STANDALONE
+ * :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
+ */
+#define X_DRIVER_TYPE  A4988
+#define Y_DRIVER_TYPE  A4988
+#define Z_DRIVER_TYPE  A4988
+#define X2_DRIVER_TYPE A4988
+#define Y2_DRIVER_TYPE A4988
+#define Z2_DRIVER_TYPE A4988
+#define E0_DRIVER_TYPE A4988
+#define E1_DRIVER_TYPE A4988
+#define E2_DRIVER_TYPE A4988
+#define E3_DRIVER_TYPE A4988
+#define E4_DRIVER_TYPE A4988
+
 // Enable this feature if all enabled endstop pins are interrupt-capable.
 // This will remove the need to poll the interrupt pins, saving many CPU cycles.
 //#define ENDSTOP_INTERRUPTS_FEATURE
--- a/Marlin/src/config/examples/Azteeg/X5GT/Configuration_adv.h
+++ b/Marlin/src/config/examples/Azteeg/X5GT/Configuration_adv.h
@ -837,15 +837,17 @@

 /**
 * Minimum delay after setting the stepper DIR (in ns)
- *    0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
- *   20 : Minimum for TMC2xxx drivers
- *  200 : Minimum for A4988 drivers
- *  500 : Minimum for LV8729 drivers (guess, no info in datasheet)
- *  650 : Minimum for DRV8825 drivers
- * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
- *15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *     0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
+ *    20 : Minimum for TMC2xxx drivers
+ *   200 : Minimum for A4988 drivers
+ *   500 : Minimum for LV8729 drivers (guess, no info in datasheet)
+ *   650 : Minimum for DRV8825 drivers
+ *  1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
+ * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_DIR_DELAY 0
+//#define MINIMUM_STEPPER_DIR_DELAY 650

 /**
 * Minimum stepper driver pulse width (in µs)
@ -855,8 +857,10 @@
 *   2 : Minimum for DRV8825 stepper drivers
 *   3 : Minimum for TB6600 stepper drivers
 *  30 : Minimum for TB6560 stepper drivers
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_PULSE 2
+//#define MINIMUM_STEPPER_PULSE 2

 /**
 * Maximum stepping rate (in Hz) the stepper driver allows
@ -867,8 +871,10 @@
 *  150000 : Maximum for TB6600 stepper driver
 *  130000 : Maximum for LV8729 stepper driver
 *   15000 : Maximum for TB6560 stepper driver
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MAXIMUM_STEPPER_RATE 250000
+//#define MAXIMUM_STEPPER_RATE 250000

 // @section temperature

@ -1036,23 +1042,12 @@
 // @section tmc

 /**
- * Enable this section if you have TMC26X motor drivers.
- * You will need to import the TMC26XStepper library into the Arduino IDE for this
- * (https://github.com/trinamic/TMC26XStepper.git)
+ * TMC26X Stepper Driver options
+ *
+ * The TMC26XStepper library is required for this stepper driver.
+ * https://github.com/trinamic/TMC26XStepper
 */
-//#define HAVE_TMC26X
-#if ENABLED(HAVE_TMC26X)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC26X
-  //#define X2_IS_TMC26X
-  //#define Y_IS_TMC26X
-  //#define Y2_IS_TMC26X
-  //#define Z_IS_TMC26X
-  //#define Z2_IS_TMC26X
-  //#define E0_IS_TMC26X
-  //#define E1_IS_TMC26X
-  //#define E2_IS_TMC26X
-  //#define E3_IS_TMC26X
-  //#define E4_IS_TMC26X
+#if HAS_DRIVER(TMC26X)

  #define X_MAX_CURRENT     1000 // in mA
  #define X_SENSE_RESISTOR    91 // in mOhms
@ -1098,62 +1093,29 @@
  #define E4_SENSE_RESISTOR   91
  #define E4_MICROSTEPS       16

-#endif
+#endif // TMC26X

 // @section tmc_smart

 /**
- * Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
- *
- * You'll also need the TMC2130Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2130Stepper).
- *
 * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
 * the hardware SPI interface on your board and define the required CS pins
 * in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
 * You may also use software SPI if you wish to use general purpose IO pins.
- */
-//#define HAVE_TMC2130
-#if ENABLED(HAVE_TMC2130)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2130
-  //#define X2_IS_TMC2130
-  //#define Y_IS_TMC2130
-  //#define Y2_IS_TMC2130
-  //#define Z_IS_TMC2130
-  //#define Z2_IS_TMC2130
-  //#define E0_IS_TMC2130
-  //#define E1_IS_TMC2130
-  //#define E2_IS_TMC2130
-  //#define E3_IS_TMC2130
-  //#define E4_IS_TMC2130
-#endif
-
-/**
- * Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
- * Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
+ *
+ * The TMC2130Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2130Stepper
+ *
+ * To use TMC2208 stepper UART-configurable stepper drivers
+ * connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
 * To use the reading capabilities, also connect #_SERIAL_RX_PIN
 * to PDN_UART without a resistor.
 * The drivers can also be used with hardware serial.
 *
- * You'll also need the TMC2208Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2208Stepper).
+ * The TMC2208Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2208Stepper
 */
-//#define HAVE_TMC2208
-#if ENABLED(HAVE_TMC2208)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2208
-  //#define X2_IS_TMC2208
-  //#define Y_IS_TMC2208
-  //#define Y2_IS_TMC2208
-  //#define Z_IS_TMC2208
-  //#define Z2_IS_TMC2208
-  //#define E0_IS_TMC2208
-  //#define E1_IS_TMC2208
-  //#define E2_IS_TMC2208
-  //#define E3_IS_TMC2208
-  //#define E4_IS_TMC2208
-#endif
-
-#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
+#if HAS_TRINAMIC

  #define R_SENSE           0.11  // R_sense resistor for SilentStepStick2130
  #define HOLD_MULTIPLIER    0.5  // Scales down the holding current from run current
@ -1308,25 +1270,12 @@
 // @section L6470

 /**
- * Enable this section if you have L6470 motor drivers.
- * You need to import the L6470 library into the Arduino IDE for this.
- * (https://github.com/ameyer/Arduino-L6470)
+ * L6470 Stepper Driver options
+ *
+ * The Arduino-L6470 library is required for this stepper driver.
+ * https://github.com/ameyer/Arduino-L6470
 */
-
-//#define HAVE_L6470DRIVER
-#if ENABLED(HAVE_L6470DRIVER)
-
-  //#define X_IS_L6470
-  //#define X2_IS_L6470
-  //#define Y_IS_L6470
-  //#define Y2_IS_L6470
-  //#define Z_IS_L6470
-  //#define Z2_IS_L6470
-  //#define E0_IS_L6470
-  //#define E1_IS_L6470
-  //#define E2_IS_L6470
-  //#define E3_IS_L6470
-  //#define E4_IS_L6470
+#if HAS_DRIVER(L6470)

  #define X_MICROSTEPS      16 // number of microsteps
  #define X_OVERCURRENT   2000 // maxc current in mA. If the current goes over this value, the driver will switch off
@ -1372,7 +1321,7 @@
  #define E4_OVERCURRENT  2000
  #define E4_STALLCURRENT 1500

-#endif
+#endif // L6470

 /**
 * TWI/I2C BUS
--- a/Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h
+++ b/Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h
@ -837,15 +837,17 @@

 /**
 * Minimum delay after setting the stepper DIR (in ns)
- *    0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
- *   20 : Minimum for TMC2xxx drivers
- *  200 : Minimum for A4988 drivers
- *  500 : Minimum for LV8729 drivers (guess, no info in datasheet)
- *  650 : Minimum for DRV8825 drivers
- * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
- *15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *     0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
+ *    20 : Minimum for TMC2xxx drivers
+ *   200 : Minimum for A4988 drivers
+ *   500 : Minimum for LV8729 drivers (guess, no info in datasheet)
+ *   650 : Minimum for DRV8825 drivers
+ *  1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
+ * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_DIR_DELAY 0
+//#define MINIMUM_STEPPER_DIR_DELAY 650

 /**
 * Minimum stepper driver pulse width (in µs)
@ -855,8 +857,10 @@
 *   2 : Minimum for DRV8825 stepper drivers
 *   3 : Minimum for TB6600 stepper drivers
 *  30 : Minimum for TB6560 stepper drivers
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_PULSE 2
+//#define MINIMUM_STEPPER_PULSE 2

 /**
 * Maximum stepping rate (in Hz) the stepper driver allows
@ -867,8 +871,10 @@
 *  150000 : Maximum for TB6600 stepper driver
 *  130000 : Maximum for LV8729 stepper driver
 *   15000 : Maximum for TB6560 stepper driver
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MAXIMUM_STEPPER_RATE 250000
+//#define MAXIMUM_STEPPER_RATE 250000

 // @section temperature

@ -1036,23 +1042,12 @@
 // @section tmc

 /**
- * Enable this section if you have TMC26X motor drivers.
- * You will need to import the TMC26XStepper library into the Arduino IDE for this
- * (https://github.com/trinamic/TMC26XStepper.git)
+ * TMC26X Stepper Driver options
+ *
+ * The TMC26XStepper library is required for this stepper driver.
+ * https://github.com/trinamic/TMC26XStepper
 */
-//#define HAVE_TMC26X
-#if ENABLED(HAVE_TMC26X)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC26X
-  //#define X2_IS_TMC26X
-  //#define Y_IS_TMC26X
-  //#define Y2_IS_TMC26X
-  //#define Z_IS_TMC26X
-  //#define Z2_IS_TMC26X
-  //#define E0_IS_TMC26X
-  //#define E1_IS_TMC26X
-  //#define E2_IS_TMC26X
-  //#define E3_IS_TMC26X
-  //#define E4_IS_TMC26X
+#if HAS_DRIVER(TMC26X)

  #define X_MAX_CURRENT     1000 // in mA
  #define X_SENSE_RESISTOR    91 // in mOhms
@ -1098,62 +1093,29 @@
  #define E4_SENSE_RESISTOR   91
  #define E4_MICROSTEPS       16

-#endif
+#endif // TMC26X

 // @section tmc_smart

 /**
- * Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
- *
- * You'll also need the TMC2130Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2130Stepper).
- *
 * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
 * the hardware SPI interface on your board and define the required CS pins
 * in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
 * You may also use software SPI if you wish to use general purpose IO pins.
- */
-//#define HAVE_TMC2130
-#if ENABLED(HAVE_TMC2130)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2130
-  //#define X2_IS_TMC2130
-  //#define Y_IS_TMC2130
-  //#define Y2_IS_TMC2130
-  //#define Z_IS_TMC2130
-  //#define Z2_IS_TMC2130
-  //#define E0_IS_TMC2130
-  //#define E1_IS_TMC2130
-  //#define E2_IS_TMC2130
-  //#define E3_IS_TMC2130
-  //#define E4_IS_TMC2130
-#endif
-
-/**
- * Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
- * Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
+ *
+ * The TMC2130Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2130Stepper
+ *
+ * To use TMC2208 stepper UART-configurable stepper drivers
+ * connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
 * To use the reading capabilities, also connect #_SERIAL_RX_PIN
 * to PDN_UART without a resistor.
 * The drivers can also be used with hardware serial.
 *
- * You'll also need the TMC2208Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2208Stepper).
+ * The TMC2208Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2208Stepper
 */
-//#define HAVE_TMC2208
-#if ENABLED(HAVE_TMC2208)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2208
-  //#define X2_IS_TMC2208
-  //#define Y_IS_TMC2208
-  //#define Y2_IS_TMC2208
-  //#define Z_IS_TMC2208
-  //#define Z2_IS_TMC2208
-  //#define E0_IS_TMC2208
-  //#define E1_IS_TMC2208
-  //#define E2_IS_TMC2208
-  //#define E3_IS_TMC2208
-  //#define E4_IS_TMC2208
-#endif
-
-#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
+#if HAS_TRINAMIC

  #define R_SENSE           0.11  // R_sense resistor for SilentStepStick2130
  #define HOLD_MULTIPLIER    0.5  // Scales down the holding current from run current
@ -1308,25 +1270,12 @@
 // @section L6470

 /**
- * Enable this section if you have L6470 motor drivers.
- * You need to import the L6470 library into the Arduino IDE for this.
- * (https://github.com/ameyer/Arduino-L6470)
+ * L6470 Stepper Driver options
+ *
+ * The Arduino-L6470 library is required for this stepper driver.
+ * https://github.com/ameyer/Arduino-L6470
 */
-
-//#define HAVE_L6470DRIVER
-#if ENABLED(HAVE_L6470DRIVER)
-
-  //#define X_IS_L6470
-  //#define X2_IS_L6470
-  //#define Y_IS_L6470
-  //#define Y2_IS_L6470
-  //#define Z_IS_L6470
-  //#define Z2_IS_L6470
-  //#define E0_IS_L6470
-  //#define E1_IS_L6470
-  //#define E2_IS_L6470
-  //#define E3_IS_L6470
-  //#define E4_IS_L6470
+#if HAS_DRIVER(L6470)

  #define X_MICROSTEPS      16 // number of microsteps
  #define X_OVERCURRENT   2000 // maxc current in mA. If the current goes over this value, the driver will switch off
@ -1372,7 +1321,7 @@
  #define E4_OVERCURRENT  2000
  #define E4_STALLCURRENT 1500

-#endif
+#endif // L6470

 /**
 * TWI/I2C BUS
--- a/Marlin/src/config/examples/BIBO/TouchX/default/Configuration_adv.h
+++ b/Marlin/src/config/examples/BIBO/TouchX/default/Configuration_adv.h
@ -837,15 +837,17 @@

 /**
 * Minimum delay after setting the stepper DIR (in ns)
- *    0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
- *   20 : Minimum for TMC2xxx drivers
- *  200 : Minimum for A4988 drivers
- *  500 : Minimum for LV8729 drivers (guess, no info in datasheet)
- *  650 : Minimum for DRV8825 drivers
- * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
- *15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *     0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
+ *    20 : Minimum for TMC2xxx drivers
+ *   200 : Minimum for A4988 drivers
+ *   500 : Minimum for LV8729 drivers (guess, no info in datasheet)
+ *   650 : Minimum for DRV8825 drivers
+ *  1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
+ * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_DIR_DELAY 0
+//#define MINIMUM_STEPPER_DIR_DELAY 650

 /**
 * Minimum stepper driver pulse width (in µs)
@ -855,8 +857,10 @@
 *   2 : Minimum for DRV8825 stepper drivers
 *   3 : Minimum for TB6600 stepper drivers
 *  30 : Minimum for TB6560 stepper drivers
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_PULSE 2
+//#define MINIMUM_STEPPER_PULSE 2

 /**
 * Maximum stepping rate (in Hz) the stepper driver allows
@ -867,8 +871,10 @@
 *  150000 : Maximum for TB6600 stepper driver
 *  130000 : Maximum for LV8729 stepper driver
 *   15000 : Maximum for TB6560 stepper driver
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MAXIMUM_STEPPER_RATE 250000
+//#define MAXIMUM_STEPPER_RATE 250000

 // @section temperature

@ -1036,23 +1042,12 @@
 // @section tmc

 /**
- * Enable this section if you have TMC26X motor drivers.
- * You will need to import the TMC26XStepper library into the Arduino IDE for this
- * (https://github.com/trinamic/TMC26XStepper.git)
+ * TMC26X Stepper Driver options
+ *
+ * The TMC26XStepper library is required for this stepper driver.
+ * https://github.com/trinamic/TMC26XStepper
 */
-//#define HAVE_TMC26X
-#if ENABLED(HAVE_TMC26X)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC26X
-  //#define X2_IS_TMC26X
-  //#define Y_IS_TMC26X
-  //#define Y2_IS_TMC26X
-  //#define Z_IS_TMC26X
-  //#define Z2_IS_TMC26X
-  //#define E0_IS_TMC26X
-  //#define E1_IS_TMC26X
-  //#define E2_IS_TMC26X
-  //#define E3_IS_TMC26X
-  //#define E4_IS_TMC26X
+#if HAS_DRIVER(TMC26X)

  #define X_MAX_CURRENT     1000 // in mA
  #define X_SENSE_RESISTOR    91 // in mOhms
@ -1098,62 +1093,29 @@
  #define E4_SENSE_RESISTOR   91
  #define E4_MICROSTEPS       16

-#endif
+#endif // TMC26X

 // @section tmc_smart

 /**
- * Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
- *
- * You'll also need the TMC2130Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2130Stepper).
- *
 * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
 * the hardware SPI interface on your board and define the required CS pins
 * in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
 * You may also use software SPI if you wish to use general purpose IO pins.
- */
-//#define HAVE_TMC2130
-#if ENABLED(HAVE_TMC2130)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2130
-  //#define X2_IS_TMC2130
-  //#define Y_IS_TMC2130
-  //#define Y2_IS_TMC2130
-  //#define Z_IS_TMC2130
-  //#define Z2_IS_TMC2130
-  //#define E0_IS_TMC2130
-  //#define E1_IS_TMC2130
-  //#define E2_IS_TMC2130
-  //#define E3_IS_TMC2130
-  //#define E4_IS_TMC2130
-#endif
-
-/**
- * Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
- * Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
+ *
+ * The TMC2130Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2130Stepper
+ *
+ * To use TMC2208 stepper UART-configurable stepper drivers
+ * connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
 * To use the reading capabilities, also connect #_SERIAL_RX_PIN
 * to PDN_UART without a resistor.
 * The drivers can also be used with hardware serial.
 *
- * You'll also need the TMC2208Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2208Stepper).
+ * The TMC2208Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2208Stepper
 */
-//#define HAVE_TMC2208
-#if ENABLED(HAVE_TMC2208)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2208
-  //#define X2_IS_TMC2208
-  //#define Y_IS_TMC2208
-  //#define Y2_IS_TMC2208
-  //#define Z_IS_TMC2208
-  //#define Z2_IS_TMC2208
-  //#define E0_IS_TMC2208
-  //#define E1_IS_TMC2208
-  //#define E2_IS_TMC2208
-  //#define E3_IS_TMC2208
-  //#define E4_IS_TMC2208
-#endif
-
-#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
+#if HAS_TRINAMIC

  #define R_SENSE           0.11  // R_sense resistor for SilentStepStick2130
  #define HOLD_MULTIPLIER    0.5  // Scales down the holding current from run current
@ -1308,25 +1270,12 @@
 // @section L6470

 /**
- * Enable this section if you have L6470 motor drivers.
- * You need to import the L6470 library into the Arduino IDE for this.
- * (https://github.com/ameyer/Arduino-L6470)
+ * L6470 Stepper Driver options
+ *
+ * The Arduino-L6470 library is required for this stepper driver.
+ * https://github.com/ameyer/Arduino-L6470
 */
-
-//#define HAVE_L6470DRIVER
-#if ENABLED(HAVE_L6470DRIVER)
-
-  //#define X_IS_L6470
-  //#define X2_IS_L6470
-  //#define Y_IS_L6470
-  //#define Y2_IS_L6470
-  //#define Z_IS_L6470
-  //#define Z2_IS_L6470
-  //#define E0_IS_L6470
-  //#define E1_IS_L6470
-  //#define E2_IS_L6470
-  //#define E3_IS_L6470
-  //#define E4_IS_L6470
+#if HAS_DRIVER(L6470)

  #define X_MICROSTEPS      16 // number of microsteps
  #define X_OVERCURRENT   2000 // maxc current in mA. If the current goes over this value, the driver will switch off
@ -1372,7 +1321,7 @@
  #define E4_OVERCURRENT  2000
  #define E4_STALLCURRENT 1500

-#endif
+#endif // L6470

 /**
 * TWI/I2C BUS
--- a/Marlin/src/config/examples/BQ/Hephestos/Configuration_adv.h
+++ b/Marlin/src/config/examples/BQ/Hephestos/Configuration_adv.h
@ -837,15 +837,17 @@

 /**
 * Minimum delay after setting the stepper DIR (in ns)
- *    0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
- *   20 : Minimum for TMC2xxx drivers
- *  200 : Minimum for A4988 drivers
- *  500 : Minimum for LV8729 drivers (guess, no info in datasheet)
- *  650 : Minimum for DRV8825 drivers
- * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
- *15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *     0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
+ *    20 : Minimum for TMC2xxx drivers
+ *   200 : Minimum for A4988 drivers
+ *   500 : Minimum for LV8729 drivers (guess, no info in datasheet)
+ *   650 : Minimum for DRV8825 drivers
+ *  1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
+ * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_DIR_DELAY 0
+//#define MINIMUM_STEPPER_DIR_DELAY 650

 /**
 * Minimum stepper driver pulse width (in µs)
@ -855,8 +857,10 @@
 *   2 : Minimum for DRV8825 stepper drivers
 *   3 : Minimum for TB6600 stepper drivers
 *  30 : Minimum for TB6560 stepper drivers
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_PULSE 2
+//#define MINIMUM_STEPPER_PULSE 2

 /**
 * Maximum stepping rate (in Hz) the stepper driver allows
@ -867,8 +871,10 @@
 *  150000 : Maximum for TB6600 stepper driver
 *  130000 : Maximum for LV8729 stepper driver
 *   15000 : Maximum for TB6560 stepper driver
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MAXIMUM_STEPPER_RATE 250000
+//#define MAXIMUM_STEPPER_RATE 250000

 // @section temperature

@ -1036,23 +1042,12 @@
 // @section tmc

 /**
- * Enable this section if you have TMC26X motor drivers.
- * You will need to import the TMC26XStepper library into the Arduino IDE for this
- * (https://github.com/trinamic/TMC26XStepper.git)
+ * TMC26X Stepper Driver options
+ *
+ * The TMC26XStepper library is required for this stepper driver.
+ * https://github.com/trinamic/TMC26XStepper
 */
-//#define HAVE_TMC26X
-#if ENABLED(HAVE_TMC26X)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC26X
-  //#define X2_IS_TMC26X
-  //#define Y_IS_TMC26X
-  //#define Y2_IS_TMC26X
-  //#define Z_IS_TMC26X
-  //#define Z2_IS_TMC26X
-  //#define E0_IS_TMC26X
-  //#define E1_IS_TMC26X
-  //#define E2_IS_TMC26X
-  //#define E3_IS_TMC26X
-  //#define E4_IS_TMC26X
+#if HAS_DRIVER(TMC26X)

  #define X_MAX_CURRENT     1000 // in mA
  #define X_SENSE_RESISTOR    91 // in mOhms
@ -1098,62 +1093,29 @@
  #define E4_SENSE_RESISTOR   91
  #define E4_MICROSTEPS       16

-#endif
+#endif // TMC26X

 // @section tmc_smart

 /**
- * Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
- *
- * You'll also need the TMC2130Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2130Stepper).
- *
 * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
 * the hardware SPI interface on your board and define the required CS pins
 * in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
 * You may also use software SPI if you wish to use general purpose IO pins.
- */
-//#define HAVE_TMC2130
-#if ENABLED(HAVE_TMC2130)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2130
-  //#define X2_IS_TMC2130
-  //#define Y_IS_TMC2130
-  //#define Y2_IS_TMC2130
-  //#define Z_IS_TMC2130
-  //#define Z2_IS_TMC2130
-  //#define E0_IS_TMC2130
-  //#define E1_IS_TMC2130
-  //#define E2_IS_TMC2130
-  //#define E3_IS_TMC2130
-  //#define E4_IS_TMC2130
-#endif
-
-/**
- * Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
- * Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
+ *
+ * The TMC2130Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2130Stepper
+ *
+ * To use TMC2208 stepper UART-configurable stepper drivers
+ * connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
 * To use the reading capabilities, also connect #_SERIAL_RX_PIN
 * to PDN_UART without a resistor.
 * The drivers can also be used with hardware serial.
 *
- * You'll also need the TMC2208Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2208Stepper).
+ * The TMC2208Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2208Stepper
 */
-//#define HAVE_TMC2208
-#if ENABLED(HAVE_TMC2208)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2208
-  //#define X2_IS_TMC2208
-  //#define Y_IS_TMC2208
-  //#define Y2_IS_TMC2208
-  //#define Z_IS_TMC2208
-  //#define Z2_IS_TMC2208
-  //#define E0_IS_TMC2208
-  //#define E1_IS_TMC2208
-  //#define E2_IS_TMC2208
-  //#define E3_IS_TMC2208
-  //#define E4_IS_TMC2208
-#endif
-
-#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
+#if HAS_TRINAMIC

  #define R_SENSE           0.11  // R_sense resistor for SilentStepStick2130
  #define HOLD_MULTIPLIER    0.5  // Scales down the holding current from run current
@ -1308,25 +1270,12 @@
 // @section L6470

 /**
- * Enable this section if you have L6470 motor drivers.
- * You need to import the L6470 library into the Arduino IDE for this.
- * (https://github.com/ameyer/Arduino-L6470)
+ * L6470 Stepper Driver options
+ *
+ * The Arduino-L6470 library is required for this stepper driver.
+ * https://github.com/ameyer/Arduino-L6470
 */
-
-//#define HAVE_L6470DRIVER
-#if ENABLED(HAVE_L6470DRIVER)
-
-  //#define X_IS_L6470
-  //#define X2_IS_L6470
-  //#define Y_IS_L6470
-  //#define Y2_IS_L6470
-  //#define Z_IS_L6470
-  //#define Z2_IS_L6470
-  //#define E0_IS_L6470
-  //#define E1_IS_L6470
-  //#define E2_IS_L6470
-  //#define E3_IS_L6470
-  //#define E4_IS_L6470
+#if HAS_DRIVER(L6470)

  #define X_MICROSTEPS      16 // number of microsteps
  #define X_OVERCURRENT   2000 // maxc current in mA. If the current goes over this value, the driver will switch off
@ -1372,7 +1321,7 @@
  #define E4_OVERCURRENT  2000
  #define E4_STALLCURRENT 1500

-#endif
+#endif // L6470

 /**
 * TWI/I2C BUS
--- a/Marlin/src/config/examples/BQ/Hephestos_2/Configuration.h
+++ b/Marlin/src/config/examples/BQ/Hephestos_2/Configuration.h
@ -552,6 +552,29 @@
 #define Z_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
 #define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.

+/**
+ * Specify Stepper Driver types
+ * The options are used to determine driver pulse timings as well as more advanced functionality.
+ * Stepper timing options can be overridden in Configuration_adv.h
+ *
+ * Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
+ *          TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
+ *          TMC26X,  TMC26X_STANDALONE,  TMC2660, TMC2660_STANDALONE,
+ *          TMC5130, TMC5130_STANDALONE
+ * :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
+ */
+#define X_DRIVER_TYPE  A4988
+#define Y_DRIVER_TYPE  A4988
+#define Z_DRIVER_TYPE  A4988
+#define X2_DRIVER_TYPE A4988
+#define Y2_DRIVER_TYPE A4988
+#define Z2_DRIVER_TYPE A4988
+#define E0_DRIVER_TYPE A4988
+#define E1_DRIVER_TYPE A4988
+#define E2_DRIVER_TYPE A4988
+#define E3_DRIVER_TYPE A4988
+#define E4_DRIVER_TYPE A4988
+
 // Enable this feature if all enabled endstop pins are interrupt-capable.
 // This will remove the need to poll the interrupt pins, saving many CPU cycles.
 #define ENDSTOP_INTERRUPTS_FEATURE
--- a/Marlin/src/config/examples/BQ/Hephestos_2/Configuration_adv.h
+++ b/Marlin/src/config/examples/BQ/Hephestos_2/Configuration_adv.h
@ -845,15 +845,17 @@

 /**
 * Minimum delay after setting the stepper DIR (in ns)
- *    0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
- *   20 : Minimum for TMC2xxx drivers
- *  200 : Minimum for A4988 drivers
- *  500 : Minimum for LV8729 drivers (guess, no info in datasheet)
- *  650 : Minimum for DRV8825 drivers
- * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
- *15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *     0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
+ *    20 : Minimum for TMC2xxx drivers
+ *   200 : Minimum for A4988 drivers
+ *   500 : Minimum for LV8729 drivers (guess, no info in datasheet)
+ *   650 : Minimum for DRV8825 drivers
+ *  1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
+ * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_DIR_DELAY 0
+//#define MINIMUM_STEPPER_DIR_DELAY 650

 /**
 * Minimum stepper driver pulse width (in µs)
@ -863,8 +865,10 @@
 *   2 : Minimum for DRV8825 stepper drivers
 *   3 : Minimum for TB6600 stepper drivers
 *  30 : Minimum for TB6560 stepper drivers
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_PULSE 2
+//#define MINIMUM_STEPPER_PULSE 2

 /**
 * Maximum stepping rate (in Hz) the stepper driver allows
@ -875,8 +879,10 @@
 *  150000 : Maximum for TB6600 stepper driver
 *  130000 : Maximum for LV8729 stepper driver
 *   15000 : Maximum for TB6560 stepper driver
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MAXIMUM_STEPPER_RATE 250000
+//#define MAXIMUM_STEPPER_RATE 250000

 // @section temperature

@ -1044,23 +1050,12 @@
 // @section tmc

 /**
- * Enable this section if you have TMC26X motor drivers.
- * You will need to import the TMC26XStepper library into the Arduino IDE for this
- * (https://github.com/trinamic/TMC26XStepper.git)
+ * TMC26X Stepper Driver options
+ *
+ * The TMC26XStepper library is required for this stepper driver.
+ * https://github.com/trinamic/TMC26XStepper
 */
-//#define HAVE_TMC26X
-#if ENABLED(HAVE_TMC26X)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC26X
-  //#define X2_IS_TMC26X
-  //#define Y_IS_TMC26X
-  //#define Y2_IS_TMC26X
-  //#define Z_IS_TMC26X
-  //#define Z2_IS_TMC26X
-  //#define E0_IS_TMC26X
-  //#define E1_IS_TMC26X
-  //#define E2_IS_TMC26X
-  //#define E3_IS_TMC26X
-  //#define E4_IS_TMC26X
+#if HAS_DRIVER(TMC26X)

  #define X_MAX_CURRENT     1000 // in mA
  #define X_SENSE_RESISTOR    91 // in mOhms
@ -1106,62 +1101,29 @@
  #define E4_SENSE_RESISTOR   91
  #define E4_MICROSTEPS       16

-#endif
+#endif // TMC26X

 // @section tmc_smart

 /**
- * Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
- *
- * You'll also need the TMC2130Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2130Stepper).
- *
 * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
 * the hardware SPI interface on your board and define the required CS pins
 * in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
 * You may also use software SPI if you wish to use general purpose IO pins.
- */
-//#define HAVE_TMC2130
-#if ENABLED(HAVE_TMC2130)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2130
-  //#define X2_IS_TMC2130
-  //#define Y_IS_TMC2130
-  //#define Y2_IS_TMC2130
-  //#define Z_IS_TMC2130
-  //#define Z2_IS_TMC2130
-  //#define E0_IS_TMC2130
-  //#define E1_IS_TMC2130
-  //#define E2_IS_TMC2130
-  //#define E3_IS_TMC2130
-  //#define E4_IS_TMC2130
-#endif
-
-/**
- * Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
- * Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
+ *
+ * The TMC2130Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2130Stepper
+ *
+ * To use TMC2208 stepper UART-configurable stepper drivers
+ * connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
 * To use the reading capabilities, also connect #_SERIAL_RX_PIN
 * to PDN_UART without a resistor.
 * The drivers can also be used with hardware serial.
 *
- * You'll also need the TMC2208Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2208Stepper).
+ * The TMC2208Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2208Stepper
 */
-//#define HAVE_TMC2208
-#if ENABLED(HAVE_TMC2208)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2208
-  //#define X2_IS_TMC2208
-  //#define Y_IS_TMC2208
-  //#define Y2_IS_TMC2208
-  //#define Z_IS_TMC2208
-  //#define Z2_IS_TMC2208
-  //#define E0_IS_TMC2208
-  //#define E1_IS_TMC2208
-  //#define E2_IS_TMC2208
-  //#define E3_IS_TMC2208
-  //#define E4_IS_TMC2208
-#endif
-
-#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
+#if HAS_TRINAMIC

  #define R_SENSE           0.11  // R_sense resistor for SilentStepStick2130
  #define HOLD_MULTIPLIER    0.5  // Scales down the holding current from run current
@ -1316,25 +1278,12 @@
 // @section L6470

 /**
- * Enable this section if you have L6470 motor drivers.
- * You need to import the L6470 library into the Arduino IDE for this.
- * (https://github.com/ameyer/Arduino-L6470)
+ * L6470 Stepper Driver options
+ *
+ * The Arduino-L6470 library is required for this stepper driver.
+ * https://github.com/ameyer/Arduino-L6470
 */
-
-//#define HAVE_L6470DRIVER
-#if ENABLED(HAVE_L6470DRIVER)
-
-  //#define X_IS_L6470
-  //#define X2_IS_L6470
-  //#define Y_IS_L6470
-  //#define Y2_IS_L6470
-  //#define Z_IS_L6470
-  //#define Z2_IS_L6470
-  //#define E0_IS_L6470
-  //#define E1_IS_L6470
-  //#define E2_IS_L6470
-  //#define E3_IS_L6470
-  //#define E4_IS_L6470
+#if HAS_DRIVER(L6470)

  #define X_MICROSTEPS      16 // number of microsteps
  #define X_OVERCURRENT   2000 // maxc current in mA. If the current goes over this value, the driver will switch off
@ -1380,7 +1329,7 @@
  #define E4_OVERCURRENT  2000
  #define E4_STALLCURRENT 1500

-#endif
+#endif // L6470

 /**
 * TWI/I2C BUS
--- a/Marlin/src/config/examples/BQ/WITBOX/Configuration_adv.h
+++ b/Marlin/src/config/examples/BQ/WITBOX/Configuration_adv.h
@ -837,15 +837,17 @@

 /**
 * Minimum delay after setting the stepper DIR (in ns)
- *    0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
- *   20 : Minimum for TMC2xxx drivers
- *  200 : Minimum for A4988 drivers
- *  500 : Minimum for LV8729 drivers (guess, no info in datasheet)
- *  650 : Minimum for DRV8825 drivers
- * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
- *15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *     0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
+ *    20 : Minimum for TMC2xxx drivers
+ *   200 : Minimum for A4988 drivers
+ *   500 : Minimum for LV8729 drivers (guess, no info in datasheet)
+ *   650 : Minimum for DRV8825 drivers
+ *  1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
+ * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_DIR_DELAY 0
+//#define MINIMUM_STEPPER_DIR_DELAY 650

 /**
 * Minimum stepper driver pulse width (in µs)
@ -855,8 +857,10 @@
 *   2 : Minimum for DRV8825 stepper drivers
 *   3 : Minimum for TB6600 stepper drivers
 *  30 : Minimum for TB6560 stepper drivers
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_PULSE 2
+//#define MINIMUM_STEPPER_PULSE 2

 /**
 * Maximum stepping rate (in Hz) the stepper driver allows
@ -867,8 +871,10 @@
 *  150000 : Maximum for TB6600 stepper driver
 *  130000 : Maximum for LV8729 stepper driver
 *   15000 : Maximum for TB6560 stepper driver
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MAXIMUM_STEPPER_RATE 250000
+//#define MAXIMUM_STEPPER_RATE 250000

 // @section temperature

@ -1036,23 +1042,12 @@
 // @section tmc

 /**
- * Enable this section if you have TMC26X motor drivers.
- * You will need to import the TMC26XStepper library into the Arduino IDE for this
- * (https://github.com/trinamic/TMC26XStepper.git)
+ * TMC26X Stepper Driver options
+ *
+ * The TMC26XStepper library is required for this stepper driver.
+ * https://github.com/trinamic/TMC26XStepper
 */
-//#define HAVE_TMC26X
-#if ENABLED(HAVE_TMC26X)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC26X
-  //#define X2_IS_TMC26X
-  //#define Y_IS_TMC26X
-  //#define Y2_IS_TMC26X
-  //#define Z_IS_TMC26X
-  //#define Z2_IS_TMC26X
-  //#define E0_IS_TMC26X
-  //#define E1_IS_TMC26X
-  //#define E2_IS_TMC26X
-  //#define E3_IS_TMC26X
-  //#define E4_IS_TMC26X
+#if HAS_DRIVER(TMC26X)

  #define X_MAX_CURRENT     1000 // in mA
  #define X_SENSE_RESISTOR    91 // in mOhms
@ -1098,62 +1093,29 @@
  #define E4_SENSE_RESISTOR   91
  #define E4_MICROSTEPS       16

-#endif
+#endif // TMC26X

 // @section tmc_smart

 /**
- * Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
- *
- * You'll also need the TMC2130Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2130Stepper).
- *
 * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
 * the hardware SPI interface on your board and define the required CS pins
 * in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
 * You may also use software SPI if you wish to use general purpose IO pins.
- */
-//#define HAVE_TMC2130
-#if ENABLED(HAVE_TMC2130)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2130
-  //#define X2_IS_TMC2130
-  //#define Y_IS_TMC2130
-  //#define Y2_IS_TMC2130
-  //#define Z_IS_TMC2130
-  //#define Z2_IS_TMC2130
-  //#define E0_IS_TMC2130
-  //#define E1_IS_TMC2130
-  //#define E2_IS_TMC2130
-  //#define E3_IS_TMC2130
-  //#define E4_IS_TMC2130
-#endif
-
-/**
- * Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
- * Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
+ *
+ * The TMC2130Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2130Stepper
+ *
+ * To use TMC2208 stepper UART-configurable stepper drivers
+ * connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
 * To use the reading capabilities, also connect #_SERIAL_RX_PIN
 * to PDN_UART without a resistor.
 * The drivers can also be used with hardware serial.
 *
- * You'll also need the TMC2208Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2208Stepper).
+ * The TMC2208Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2208Stepper
 */
-//#define HAVE_TMC2208
-#if ENABLED(HAVE_TMC2208)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2208
-  //#define X2_IS_TMC2208
-  //#define Y_IS_TMC2208
-  //#define Y2_IS_TMC2208
-  //#define Z_IS_TMC2208
-  //#define Z2_IS_TMC2208
-  //#define E0_IS_TMC2208
-  //#define E1_IS_TMC2208
-  //#define E2_IS_TMC2208
-  //#define E3_IS_TMC2208
-  //#define E4_IS_TMC2208
-#endif
-
-#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
+#if HAS_TRINAMIC

  #define R_SENSE           0.11  // R_sense resistor for SilentStepStick2130
  #define HOLD_MULTIPLIER    0.5  // Scales down the holding current from run current
@ -1308,25 +1270,12 @@
 // @section L6470

 /**
- * Enable this section if you have L6470 motor drivers.
- * You need to import the L6470 library into the Arduino IDE for this.
- * (https://github.com/ameyer/Arduino-L6470)
+ * L6470 Stepper Driver options
+ *
+ * The Arduino-L6470 library is required for this stepper driver.
+ * https://github.com/ameyer/Arduino-L6470
 */
-
-//#define HAVE_L6470DRIVER
-#if ENABLED(HAVE_L6470DRIVER)
-
-  //#define X_IS_L6470
-  //#define X2_IS_L6470
-  //#define Y_IS_L6470
-  //#define Y2_IS_L6470
-  //#define Z_IS_L6470
-  //#define Z2_IS_L6470
-  //#define E0_IS_L6470
-  //#define E1_IS_L6470
-  //#define E2_IS_L6470
-  //#define E3_IS_L6470
-  //#define E4_IS_L6470
+#if HAS_DRIVER(L6470)

  #define X_MICROSTEPS      16 // number of microsteps
  #define X_OVERCURRENT   2000 // maxc current in mA. If the current goes over this value, the driver will switch off
@ -1372,7 +1321,7 @@
  #define E4_OVERCURRENT  2000
  #define E4_STALLCURRENT 1500

-#endif
+#endif // L6470

 /**
 * TWI/I2C BUS
--- a/Marlin/src/config/examples/Cartesio/Configuration_adv.h
+++ b/Marlin/src/config/examples/Cartesio/Configuration_adv.h
@ -837,15 +837,17 @@

 /**
 * Minimum delay after setting the stepper DIR (in ns)
- *    0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
- *   20 : Minimum for TMC2xxx drivers
- *  200 : Minimum for A4988 drivers
- *  500 : Minimum for LV8729 drivers (guess, no info in datasheet)
- *  650 : Minimum for DRV8825 drivers
- * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
- *15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *     0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
+ *    20 : Minimum for TMC2xxx drivers
+ *   200 : Minimum for A4988 drivers
+ *   500 : Minimum for LV8729 drivers (guess, no info in datasheet)
+ *   650 : Minimum for DRV8825 drivers
+ *  1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
+ * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_DIR_DELAY 0
+//#define MINIMUM_STEPPER_DIR_DELAY 650

 /**
 * Minimum stepper driver pulse width (in µs)
@ -855,8 +857,10 @@
 *   2 : Minimum for DRV8825 stepper drivers
 *   3 : Minimum for TB6600 stepper drivers
 *  30 : Minimum for TB6560 stepper drivers
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_PULSE 2
+//#define MINIMUM_STEPPER_PULSE 2

 /**
 * Maximum stepping rate (in Hz) the stepper driver allows
@ -867,8 +871,10 @@
 *  150000 : Maximum for TB6600 stepper driver
 *  130000 : Maximum for LV8729 stepper driver
 *   15000 : Maximum for TB6560 stepper driver
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MAXIMUM_STEPPER_RATE 250000
+//#define MAXIMUM_STEPPER_RATE 250000

 // @section temperature

@ -1036,23 +1042,12 @@
 // @section tmc

 /**
- * Enable this section if you have TMC26X motor drivers.
- * You will need to import the TMC26XStepper library into the Arduino IDE for this
- * (https://github.com/trinamic/TMC26XStepper.git)
+ * TMC26X Stepper Driver options
+ *
+ * The TMC26XStepper library is required for this stepper driver.
+ * https://github.com/trinamic/TMC26XStepper
 */
-//#define HAVE_TMC26X
-#if ENABLED(HAVE_TMC26X)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC26X
-  //#define X2_IS_TMC26X
-  //#define Y_IS_TMC26X
-  //#define Y2_IS_TMC26X
-  //#define Z_IS_TMC26X
-  //#define Z2_IS_TMC26X
-  //#define E0_IS_TMC26X
-  //#define E1_IS_TMC26X
-  //#define E2_IS_TMC26X
-  //#define E3_IS_TMC26X
-  //#define E4_IS_TMC26X
+#if HAS_DRIVER(TMC26X)

  #define X_MAX_CURRENT     1000 // in mA
  #define X_SENSE_RESISTOR    91 // in mOhms
@ -1098,62 +1093,29 @@
  #define E4_SENSE_RESISTOR   91
  #define E4_MICROSTEPS       16

-#endif
+#endif // TMC26X

 // @section tmc_smart

 /**
- * Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
- *
- * You'll also need the TMC2130Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2130Stepper).
- *
 * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
 * the hardware SPI interface on your board and define the required CS pins
 * in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
 * You may also use software SPI if you wish to use general purpose IO pins.
- */
-//#define HAVE_TMC2130
-#if ENABLED(HAVE_TMC2130)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2130
-  //#define X2_IS_TMC2130
-  //#define Y_IS_TMC2130
-  //#define Y2_IS_TMC2130
-  //#define Z_IS_TMC2130
-  //#define Z2_IS_TMC2130
-  //#define E0_IS_TMC2130
-  //#define E1_IS_TMC2130
-  //#define E2_IS_TMC2130
-  //#define E3_IS_TMC2130
-  //#define E4_IS_TMC2130
-#endif
-
-/**
- * Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
- * Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
+ *
+ * The TMC2130Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2130Stepper
+ *
+ * To use TMC2208 stepper UART-configurable stepper drivers
+ * connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
 * To use the reading capabilities, also connect #_SERIAL_RX_PIN
 * to PDN_UART without a resistor.
 * The drivers can also be used with hardware serial.
 *
- * You'll also need the TMC2208Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2208Stepper).
+ * The TMC2208Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2208Stepper
 */
-//#define HAVE_TMC2208
-#if ENABLED(HAVE_TMC2208)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2208
-  //#define X2_IS_TMC2208
-  //#define Y_IS_TMC2208
-  //#define Y2_IS_TMC2208
-  //#define Z_IS_TMC2208
-  //#define Z2_IS_TMC2208
-  //#define E0_IS_TMC2208
-  //#define E1_IS_TMC2208
-  //#define E2_IS_TMC2208
-  //#define E3_IS_TMC2208
-  //#define E4_IS_TMC2208
-#endif
-
-#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
+#if HAS_TRINAMIC

  #define R_SENSE           0.11  // R_sense resistor for SilentStepStick2130
  #define HOLD_MULTIPLIER    0.5  // Scales down the holding current from run current
@ -1308,25 +1270,12 @@
 // @section L6470

 /**
- * Enable this section if you have L6470 motor drivers.
- * You need to import the L6470 library into the Arduino IDE for this.
- * (https://github.com/ameyer/Arduino-L6470)
+ * L6470 Stepper Driver options
+ *
+ * The Arduino-L6470 library is required for this stepper driver.
+ * https://github.com/ameyer/Arduino-L6470
 */
-
-//#define HAVE_L6470DRIVER
-#if ENABLED(HAVE_L6470DRIVER)
-
-  //#define X_IS_L6470
-  //#define X2_IS_L6470
-  //#define Y_IS_L6470
-  //#define Y2_IS_L6470
-  //#define Z_IS_L6470
-  //#define Z2_IS_L6470
-  //#define E0_IS_L6470
-  //#define E1_IS_L6470
-  //#define E2_IS_L6470
-  //#define E3_IS_L6470
-  //#define E4_IS_L6470
+#if HAS_DRIVER(L6470)

  #define X_MICROSTEPS      16 // number of microsteps
  #define X_OVERCURRENT   2000 // maxc current in mA. If the current goes over this value, the driver will switch off
@ -1372,7 +1321,7 @@
  #define E4_OVERCURRENT  2000
  #define E4_STALLCURRENT 1500

-#endif
+#endif // L6470

 /**
 * TWI/I2C BUS
--- a/Marlin/src/config/examples/Creality/CR-10/Configuration.h
+++ b/Marlin/src/config/examples/Creality/CR-10/Configuration.h
@ -561,6 +561,29 @@
 #define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
 #define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.

+/**
+ * Specify Stepper Driver types
+ * The options are used to determine driver pulse timings as well as more advanced functionality.
+ * Stepper timing options can be overridden in Configuration_adv.h
+ *
+ * Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
+ *          TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
+ *          TMC26X,  TMC26X_STANDALONE,  TMC2660, TMC2660_STANDALONE,
+ *          TMC5130, TMC5130_STANDALONE
+ * :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
+ */
+#define X_DRIVER_TYPE  A4988
+#define Y_DRIVER_TYPE  A4988
+#define Z_DRIVER_TYPE  A4988
+#define X2_DRIVER_TYPE A4988
+#define Y2_DRIVER_TYPE A4988
+#define Z2_DRIVER_TYPE A4988
+#define E0_DRIVER_TYPE A4988
+#define E1_DRIVER_TYPE A4988
+#define E2_DRIVER_TYPE A4988
+#define E3_DRIVER_TYPE A4988
+#define E4_DRIVER_TYPE A4988
+
 // Enable this feature if all enabled endstop pins are interrupt-capable.
 // This will remove the need to poll the interrupt pins, saving many CPU cycles.
 //#define ENDSTOP_INTERRUPTS_FEATURE
--- a/Marlin/src/config/examples/Creality/CR-10/Configuration_adv.h
+++ b/Marlin/src/config/examples/Creality/CR-10/Configuration_adv.h
@ -837,15 +837,17 @@

 /**
 * Minimum delay after setting the stepper DIR (in ns)
- *    0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
- *   20 : Minimum for TMC2xxx drivers
- *  200 : Minimum for A4988 drivers
- *  500 : Minimum for LV8729 drivers (guess, no info in datasheet)
- *  650 : Minimum for DRV8825 drivers
- * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
- *15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *     0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
+ *    20 : Minimum for TMC2xxx drivers
+ *   200 : Minimum for A4988 drivers
+ *   500 : Minimum for LV8729 drivers (guess, no info in datasheet)
+ *   650 : Minimum for DRV8825 drivers
+ *  1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
+ * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_DIR_DELAY 0
+//#define MINIMUM_STEPPER_DIR_DELAY 650

 /**
 * Minimum stepper driver pulse width (in µs)
@ -855,8 +857,10 @@
 *   2 : Minimum for DRV8825 stepper drivers
 *   3 : Minimum for TB6600 stepper drivers
 *  30 : Minimum for TB6560 stepper drivers
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_PULSE 2
+//#define MINIMUM_STEPPER_PULSE 2

 /**
 * Maximum stepping rate (in Hz) the stepper driver allows
@ -867,8 +871,10 @@
 *  150000 : Maximum for TB6600 stepper driver
 *  130000 : Maximum for LV8729 stepper driver
 *   15000 : Maximum for TB6560 stepper driver
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MAXIMUM_STEPPER_RATE 250000
+//#define MAXIMUM_STEPPER_RATE 250000

 // @section temperature

@ -1036,23 +1042,12 @@
 // @section tmc

 /**
- * Enable this section if you have TMC26X motor drivers.
- * You will need to import the TMC26XStepper library into the Arduino IDE for this
- * (https://github.com/trinamic/TMC26XStepper.git)
+ * TMC26X Stepper Driver options
+ *
+ * The TMC26XStepper library is required for this stepper driver.
+ * https://github.com/trinamic/TMC26XStepper
 */
-//#define HAVE_TMC26X
-#if ENABLED(HAVE_TMC26X)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC26X
-  //#define X2_IS_TMC26X
-  //#define Y_IS_TMC26X
-  //#define Y2_IS_TMC26X
-  //#define Z_IS_TMC26X
-  //#define Z2_IS_TMC26X
-  //#define E0_IS_TMC26X
-  //#define E1_IS_TMC26X
-  //#define E2_IS_TMC26X
-  //#define E3_IS_TMC26X
-  //#define E4_IS_TMC26X
+#if HAS_DRIVER(TMC26X)

  #define X_MAX_CURRENT     1000 // in mA
  #define X_SENSE_RESISTOR    91 // in mOhms
@ -1098,62 +1093,29 @@
  #define E4_SENSE_RESISTOR   91
  #define E4_MICROSTEPS       16

-#endif
+#endif // TMC26X

 // @section tmc_smart

 /**
- * Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
- *
- * You'll also need the TMC2130Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2130Stepper).
- *
 * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
 * the hardware SPI interface on your board and define the required CS pins
 * in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
 * You may also use software SPI if you wish to use general purpose IO pins.
- */
-//#define HAVE_TMC2130
-#if ENABLED(HAVE_TMC2130)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2130
-  //#define X2_IS_TMC2130
-  //#define Y_IS_TMC2130
-  //#define Y2_IS_TMC2130
-  //#define Z_IS_TMC2130
-  //#define Z2_IS_TMC2130
-  //#define E0_IS_TMC2130
-  //#define E1_IS_TMC2130
-  //#define E2_IS_TMC2130
-  //#define E3_IS_TMC2130
-  //#define E4_IS_TMC2130
-#endif
-
-/**
- * Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
- * Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
+ *
+ * The TMC2130Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2130Stepper
+ *
+ * To use TMC2208 stepper UART-configurable stepper drivers
+ * connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
 * To use the reading capabilities, also connect #_SERIAL_RX_PIN
 * to PDN_UART without a resistor.
 * The drivers can also be used with hardware serial.
 *
- * You'll also need the TMC2208Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2208Stepper).
+ * The TMC2208Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2208Stepper
 */
-//#define HAVE_TMC2208
-#if ENABLED(HAVE_TMC2208)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2208
-  //#define X2_IS_TMC2208
-  //#define Y_IS_TMC2208
-  //#define Y2_IS_TMC2208
-  //#define Z_IS_TMC2208
-  //#define Z2_IS_TMC2208
-  //#define E0_IS_TMC2208
-  //#define E1_IS_TMC2208
-  //#define E2_IS_TMC2208
-  //#define E3_IS_TMC2208
-  //#define E4_IS_TMC2208
-#endif
-
-#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
+#if HAS_TRINAMIC

  #define R_SENSE           0.11  // R_sense resistor for SilentStepStick2130
  #define HOLD_MULTIPLIER    0.5  // Scales down the holding current from run current
@ -1308,25 +1270,12 @@
 // @section L6470

 /**
- * Enable this section if you have L6470 motor drivers.
- * You need to import the L6470 library into the Arduino IDE for this.
- * (https://github.com/ameyer/Arduino-L6470)
+ * L6470 Stepper Driver options
+ *
+ * The Arduino-L6470 library is required for this stepper driver.
+ * https://github.com/ameyer/Arduino-L6470
 */
-
-//#define HAVE_L6470DRIVER
-#if ENABLED(HAVE_L6470DRIVER)
-
-  //#define X_IS_L6470
-  //#define X2_IS_L6470
-  //#define Y_IS_L6470
-  //#define Y2_IS_L6470
-  //#define Z_IS_L6470
-  //#define Z2_IS_L6470
-  //#define E0_IS_L6470
-  //#define E1_IS_L6470
-  //#define E2_IS_L6470
-  //#define E3_IS_L6470
-  //#define E4_IS_L6470
+#if HAS_DRIVER(L6470)

  #define X_MICROSTEPS      16 // number of microsteps
  #define X_OVERCURRENT   2000 // maxc current in mA. If the current goes over this value, the driver will switch off
@ -1372,7 +1321,7 @@
  #define E4_OVERCURRENT  2000
  #define E4_STALLCURRENT 1500

-#endif
+#endif // L6470

 /**
 * TWI/I2C BUS
--- a/Marlin/src/config/examples/Creality/CR-10S/Configuration.h
+++ b/Marlin/src/config/examples/Creality/CR-10S/Configuration.h
@ -551,6 +551,29 @@
 #define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
 #define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.

+/**
+ * Specify Stepper Driver types
+ * The options are used to determine driver pulse timings as well as more advanced functionality.
+ * Stepper timing options can be overridden in Configuration_adv.h
+ *
+ * Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
+ *          TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
+ *          TMC26X,  TMC26X_STANDALONE,  TMC2660, TMC2660_STANDALONE,
+ *          TMC5130, TMC5130_STANDALONE
+ * :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
+ */
+#define X_DRIVER_TYPE  A4988
+#define Y_DRIVER_TYPE  A4988
+#define Z_DRIVER_TYPE  A4988
+#define X2_DRIVER_TYPE A4988
+#define Y2_DRIVER_TYPE A4988
+#define Z2_DRIVER_TYPE A4988
+#define E0_DRIVER_TYPE A4988
+#define E1_DRIVER_TYPE A4988
+#define E2_DRIVER_TYPE A4988
+#define E3_DRIVER_TYPE A4988
+#define E4_DRIVER_TYPE A4988
+
 // Enable this feature if all enabled endstop pins are interrupt-capable.
 // This will remove the need to poll the interrupt pins, saving many CPU cycles.
 //#define ENDSTOP_INTERRUPTS_FEATURE
--- a/Marlin/src/config/examples/Creality/CR-10S/Configuration_adv.h
+++ b/Marlin/src/config/examples/Creality/CR-10S/Configuration_adv.h
@ -837,15 +837,17 @@

 /**
 * Minimum delay after setting the stepper DIR (in ns)
- *    0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
- *   20 : Minimum for TMC2xxx drivers
- *  200 : Minimum for A4988 drivers
- *  500 : Minimum for LV8729 drivers (guess, no info in datasheet)
- *  650 : Minimum for DRV8825 drivers
- * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
- *15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *     0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
+ *    20 : Minimum for TMC2xxx drivers
+ *   200 : Minimum for A4988 drivers
+ *   500 : Minimum for LV8729 drivers (guess, no info in datasheet)
+ *   650 : Minimum for DRV8825 drivers
+ *  1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
+ * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_DIR_DELAY 0
+//#define MINIMUM_STEPPER_DIR_DELAY 650

 /**
 * Minimum stepper driver pulse width (in µs)
@ -855,8 +857,10 @@
 *   2 : Minimum for DRV8825 stepper drivers
 *   3 : Minimum for TB6600 stepper drivers
 *  30 : Minimum for TB6560 stepper drivers
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_PULSE 2
+//#define MINIMUM_STEPPER_PULSE 2

 /**
 * Maximum stepping rate (in Hz) the stepper driver allows
@ -867,8 +871,10 @@
 *  150000 : Maximum for TB6600 stepper driver
 *  130000 : Maximum for LV8729 stepper driver
 *   15000 : Maximum for TB6560 stepper driver
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MAXIMUM_STEPPER_RATE 250000
+//#define MAXIMUM_STEPPER_RATE 250000

 // @section temperature

@ -1036,23 +1042,12 @@
 // @section tmc

 /**
- * Enable this section if you have TMC26X motor drivers.
- * You will need to import the TMC26XStepper library into the Arduino IDE for this
- * (https://github.com/trinamic/TMC26XStepper.git)
+ * TMC26X Stepper Driver options
+ *
+ * The TMC26XStepper library is required for this stepper driver.
+ * https://github.com/trinamic/TMC26XStepper
 */
-//#define HAVE_TMC26X
-#if ENABLED(HAVE_TMC26X)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC26X
-  //#define X2_IS_TMC26X
-  //#define Y_IS_TMC26X
-  //#define Y2_IS_TMC26X
-  //#define Z_IS_TMC26X
-  //#define Z2_IS_TMC26X
-  //#define E0_IS_TMC26X
-  //#define E1_IS_TMC26X
-  //#define E2_IS_TMC26X
-  //#define E3_IS_TMC26X
-  //#define E4_IS_TMC26X
+#if HAS_DRIVER(TMC26X)

  #define X_MAX_CURRENT     1000 // in mA
  #define X_SENSE_RESISTOR    91 // in mOhms
@ -1098,62 +1093,29 @@
  #define E4_SENSE_RESISTOR   91
  #define E4_MICROSTEPS       16

-#endif
+#endif // TMC26X

 // @section tmc_smart

 /**
- * Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
- *
- * You'll also need the TMC2130Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2130Stepper).
- *
 * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
 * the hardware SPI interface on your board and define the required CS pins
 * in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
 * You may also use software SPI if you wish to use general purpose IO pins.
- */
-//#define HAVE_TMC2130
-#if ENABLED(HAVE_TMC2130)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2130
-  //#define X2_IS_TMC2130
-  //#define Y_IS_TMC2130
-  //#define Y2_IS_TMC2130
-  //#define Z_IS_TMC2130
-  //#define Z2_IS_TMC2130
-  //#define E0_IS_TMC2130
-  //#define E1_IS_TMC2130
-  //#define E2_IS_TMC2130
-  //#define E3_IS_TMC2130
-  //#define E4_IS_TMC2130
-#endif
-
-/**
- * Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
- * Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
+ *
+ * The TMC2130Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2130Stepper
+ *
+ * To use TMC2208 stepper UART-configurable stepper drivers
+ * connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
 * To use the reading capabilities, also connect #_SERIAL_RX_PIN
 * to PDN_UART without a resistor.
 * The drivers can also be used with hardware serial.
 *
- * You'll also need the TMC2208Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2208Stepper).
+ * The TMC2208Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2208Stepper
 */
-//#define HAVE_TMC2208
-#if ENABLED(HAVE_TMC2208)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2208
-  //#define X2_IS_TMC2208
-  //#define Y_IS_TMC2208
-  //#define Y2_IS_TMC2208
-  //#define Z_IS_TMC2208
-  //#define Z2_IS_TMC2208
-  //#define E0_IS_TMC2208
-  //#define E1_IS_TMC2208
-  //#define E2_IS_TMC2208
-  //#define E3_IS_TMC2208
-  //#define E4_IS_TMC2208
-#endif
-
-#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
+#if HAS_TRINAMIC

  #define R_SENSE           0.11  // R_sense resistor for SilentStepStick2130
  #define HOLD_MULTIPLIER    0.5  // Scales down the holding current from run current
@ -1308,25 +1270,12 @@
 // @section L6470

 /**
- * Enable this section if you have L6470 motor drivers.
- * You need to import the L6470 library into the Arduino IDE for this.
- * (https://github.com/ameyer/Arduino-L6470)
+ * L6470 Stepper Driver options
+ *
+ * The Arduino-L6470 library is required for this stepper driver.
+ * https://github.com/ameyer/Arduino-L6470
 */
-
-//#define HAVE_L6470DRIVER
-#if ENABLED(HAVE_L6470DRIVER)
-
-  //#define X_IS_L6470
-  //#define X2_IS_L6470
-  //#define Y_IS_L6470
-  //#define Y2_IS_L6470
-  //#define Z_IS_L6470
-  //#define Z2_IS_L6470
-  //#define E0_IS_L6470
-  //#define E1_IS_L6470
-  //#define E2_IS_L6470
-  //#define E3_IS_L6470
-  //#define E4_IS_L6470
+#if HAS_DRIVER(L6470)

  #define X_MICROSTEPS      16 // number of microsteps
  #define X_OVERCURRENT   2000 // maxc current in mA. If the current goes over this value, the driver will switch off
@ -1372,7 +1321,7 @@
  #define E4_OVERCURRENT  2000
  #define E4_STALLCURRENT 1500

-#endif
+#endif // L6470

 /**
 * TWI/I2C BUS
--- a/Marlin/src/config/examples/Creality/CR-10mini/Configuration.h
+++ b/Marlin/src/config/examples/Creality/CR-10mini/Configuration.h
@ -570,6 +570,29 @@
 #define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
 #define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.

+/**
+ * Specify Stepper Driver types
+ * The options are used to determine driver pulse timings as well as more advanced functionality.
+ * Stepper timing options can be overridden in Configuration_adv.h
+ *
+ * Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
+ *          TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
+ *          TMC26X,  TMC26X_STANDALONE,  TMC2660, TMC2660_STANDALONE,
+ *          TMC5130, TMC5130_STANDALONE
+ * :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
+ */
+#define X_DRIVER_TYPE  A4988
+#define Y_DRIVER_TYPE  A4988
+#define Z_DRIVER_TYPE  A4988
+#define X2_DRIVER_TYPE A4988
+#define Y2_DRIVER_TYPE A4988
+#define Z2_DRIVER_TYPE A4988
+#define E0_DRIVER_TYPE A4988
+#define E1_DRIVER_TYPE A4988
+#define E2_DRIVER_TYPE A4988
+#define E3_DRIVER_TYPE A4988
+#define E4_DRIVER_TYPE A4988
+
 // Enable this feature if all enabled endstop pins are interrupt-capable.
 // This will remove the need to poll the interrupt pins, saving many CPU cycles.
 //#define ENDSTOP_INTERRUPTS_FEATURE
--- a/Marlin/src/config/examples/Creality/CR-10mini/Configuration_adv.h
+++ b/Marlin/src/config/examples/Creality/CR-10mini/Configuration_adv.h
@ -837,15 +837,17 @@

 /**
 * Minimum delay after setting the stepper DIR (in ns)
- *    0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
- *   20 : Minimum for TMC2xxx drivers
- *  200 : Minimum for A4988 drivers
- *  500 : Minimum for LV8729 drivers (guess, no info in datasheet)
- *  650 : Minimum for DRV8825 drivers
- * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
- *15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *     0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
+ *    20 : Minimum for TMC2xxx drivers
+ *   200 : Minimum for A4988 drivers
+ *   500 : Minimum for LV8729 drivers (guess, no info in datasheet)
+ *   650 : Minimum for DRV8825 drivers
+ *  1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
+ * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_DIR_DELAY 0
+//#define MINIMUM_STEPPER_DIR_DELAY 650

 /**
 * Minimum stepper driver pulse width (in µs)
@ -855,8 +857,10 @@
 *   2 : Minimum for DRV8825 stepper drivers
 *   3 : Minimum for TB6600 stepper drivers
 *  30 : Minimum for TB6560 stepper drivers
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_PULSE 2
+//#define MINIMUM_STEPPER_PULSE 2

 /**
 * Maximum stepping rate (in Hz) the stepper driver allows
@ -867,8 +871,10 @@
 *  150000 : Maximum for TB6600 stepper driver
 *  130000 : Maximum for LV8729 stepper driver
 *   15000 : Maximum for TB6560 stepper driver
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MAXIMUM_STEPPER_RATE 250000
+//#define MAXIMUM_STEPPER_RATE 250000

 // @section temperature

@ -1036,23 +1042,12 @@
 // @section tmc

 /**
- * Enable this section if you have TMC26X motor drivers.
- * You will need to import the TMC26XStepper library into the Arduino IDE for this
- * (https://github.com/trinamic/TMC26XStepper.git)
+ * TMC26X Stepper Driver options
+ *
+ * The TMC26XStepper library is required for this stepper driver.
+ * https://github.com/trinamic/TMC26XStepper
 */
-//#define HAVE_TMC26X
-#if ENABLED(HAVE_TMC26X)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC26X
-  //#define X2_IS_TMC26X
-  //#define Y_IS_TMC26X
-  //#define Y2_IS_TMC26X
-  //#define Z_IS_TMC26X
-  //#define Z2_IS_TMC26X
-  //#define E0_IS_TMC26X
-  //#define E1_IS_TMC26X
-  //#define E2_IS_TMC26X
-  //#define E3_IS_TMC26X
-  //#define E4_IS_TMC26X
+#if HAS_DRIVER(TMC26X)

  #define X_MAX_CURRENT     1000 // in mA
  #define X_SENSE_RESISTOR    91 // in mOhms
@ -1098,62 +1093,29 @@
  #define E4_SENSE_RESISTOR   91
  #define E4_MICROSTEPS       16

-#endif
+#endif // TMC26X

 // @section tmc_smart

 /**
- * Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
- *
- * You'll also need the TMC2130Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2130Stepper).
- *
 * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
 * the hardware SPI interface on your board and define the required CS pins
 * in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
 * You may also use software SPI if you wish to use general purpose IO pins.
- */
-//#define HAVE_TMC2130
-#if ENABLED(HAVE_TMC2130)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2130
-  //#define X2_IS_TMC2130
-  //#define Y_IS_TMC2130
-  //#define Y2_IS_TMC2130
-  //#define Z_IS_TMC2130
-  //#define Z2_IS_TMC2130
-  //#define E0_IS_TMC2130
-  //#define E1_IS_TMC2130
-  //#define E2_IS_TMC2130
-  //#define E3_IS_TMC2130
-  //#define E4_IS_TMC2130
-#endif
-
-/**
- * Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
- * Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
+ *
+ * The TMC2130Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2130Stepper
+ *
+ * To use TMC2208 stepper UART-configurable stepper drivers
+ * connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
 * To use the reading capabilities, also connect #_SERIAL_RX_PIN
 * to PDN_UART without a resistor.
 * The drivers can also be used with hardware serial.
 *
- * You'll also need the TMC2208Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2208Stepper).
+ * The TMC2208Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2208Stepper
 */
-//#define HAVE_TMC2208
-#if ENABLED(HAVE_TMC2208)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2208
-  //#define X2_IS_TMC2208
-  //#define Y_IS_TMC2208
-  //#define Y2_IS_TMC2208
-  //#define Z_IS_TMC2208
-  //#define Z2_IS_TMC2208
-  //#define E0_IS_TMC2208
-  //#define E1_IS_TMC2208
-  //#define E2_IS_TMC2208
-  //#define E3_IS_TMC2208
-  //#define E4_IS_TMC2208
-#endif
-
-#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
+#if HAS_TRINAMIC

  #define R_SENSE           0.11  // R_sense resistor for SilentStepStick2130
  #define HOLD_MULTIPLIER    0.5  // Scales down the holding current from run current
@ -1308,25 +1270,12 @@
 // @section L6470

 /**
- * Enable this section if you have L6470 motor drivers.
- * You need to import the L6470 library into the Arduino IDE for this.
- * (https://github.com/ameyer/Arduino-L6470)
+ * L6470 Stepper Driver options
+ *
+ * The Arduino-L6470 library is required for this stepper driver.
+ * https://github.com/ameyer/Arduino-L6470
 */
-
-//#define HAVE_L6470DRIVER
-#if ENABLED(HAVE_L6470DRIVER)
-
-  //#define X_IS_L6470
-  //#define X2_IS_L6470
-  //#define Y_IS_L6470
-  //#define Y2_IS_L6470
-  //#define Z_IS_L6470
-  //#define Z2_IS_L6470
-  //#define E0_IS_L6470
-  //#define E1_IS_L6470
-  //#define E2_IS_L6470
-  //#define E3_IS_L6470
-  //#define E4_IS_L6470
+#if HAS_DRIVER(L6470)

  #define X_MICROSTEPS      16 // number of microsteps
  #define X_OVERCURRENT   2000 // maxc current in mA. If the current goes over this value, the driver will switch off
@ -1372,7 +1321,7 @@
  #define E4_OVERCURRENT  2000
  #define E4_STALLCURRENT 1500

-#endif
+#endif // L6470

 /**
 * TWI/I2C BUS
--- a/Marlin/src/config/examples/Creality/CR-8/Configuration.h
+++ b/Marlin/src/config/examples/Creality/CR-8/Configuration.h
@ -561,6 +561,29 @@
 #define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
 #define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.

+/**
+ * Specify Stepper Driver types
+ * The options are used to determine driver pulse timings as well as more advanced functionality.
+ * Stepper timing options can be overridden in Configuration_adv.h
+ *
+ * Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
+ *          TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
+ *          TMC26X,  TMC26X_STANDALONE,  TMC2660, TMC2660_STANDALONE,
+ *          TMC5130, TMC5130_STANDALONE
+ * :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
+ */
+#define X_DRIVER_TYPE  A4988
+#define Y_DRIVER_TYPE  A4988
+#define Z_DRIVER_TYPE  A4988
+#define X2_DRIVER_TYPE A4988
+#define Y2_DRIVER_TYPE A4988
+#define Z2_DRIVER_TYPE A4988
+#define E0_DRIVER_TYPE A4988
+#define E1_DRIVER_TYPE A4988
+#define E2_DRIVER_TYPE A4988
+#define E3_DRIVER_TYPE A4988
+#define E4_DRIVER_TYPE A4988
+
 // Enable this feature if all enabled endstop pins are interrupt-capable.
 // This will remove the need to poll the interrupt pins, saving many CPU cycles.
 //#define ENDSTOP_INTERRUPTS_FEATURE
--- a/Marlin/src/config/examples/Creality/CR-8/Configuration_adv.h
+++ b/Marlin/src/config/examples/Creality/CR-8/Configuration_adv.h
@ -837,15 +837,17 @@

 /**
 * Minimum delay after setting the stepper DIR (in ns)
- *    0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
- *   20 : Minimum for TMC2xxx drivers
- *  200 : Minimum for A4988 drivers
- *  500 : Minimum for LV8729 drivers (guess, no info in datasheet)
- *  650 : Minimum for DRV8825 drivers
- * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
- *15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *     0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
+ *    20 : Minimum for TMC2xxx drivers
+ *   200 : Minimum for A4988 drivers
+ *   500 : Minimum for LV8729 drivers (guess, no info in datasheet)
+ *   650 : Minimum for DRV8825 drivers
+ *  1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
+ * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_DIR_DELAY 0
+//#define MINIMUM_STEPPER_DIR_DELAY 650

 /**
 * Minimum stepper driver pulse width (in µs)
@ -855,8 +857,10 @@
 *   2 : Minimum for DRV8825 stepper drivers
 *   3 : Minimum for TB6600 stepper drivers
 *  30 : Minimum for TB6560 stepper drivers
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_PULSE 2
+//#define MINIMUM_STEPPER_PULSE 2

 /**
 * Maximum stepping rate (in Hz) the stepper driver allows
@ -867,8 +871,10 @@
 *  150000 : Maximum for TB6600 stepper driver
 *  130000 : Maximum for LV8729 stepper driver
 *   15000 : Maximum for TB6560 stepper driver
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MAXIMUM_STEPPER_RATE 250000
+//#define MAXIMUM_STEPPER_RATE 250000

 // @section temperature

@ -1036,23 +1042,12 @@
 // @section tmc

 /**
- * Enable this section if you have TMC26X motor drivers.
- * You will need to import the TMC26XStepper library into the Arduino IDE for this
- * (https://github.com/trinamic/TMC26XStepper.git)
+ * TMC26X Stepper Driver options
+ *
+ * The TMC26XStepper library is required for this stepper driver.
+ * https://github.com/trinamic/TMC26XStepper
 */
-//#define HAVE_TMC26X
-#if ENABLED(HAVE_TMC26X)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC26X
-  //#define X2_IS_TMC26X
-  //#define Y_IS_TMC26X
-  //#define Y2_IS_TMC26X
-  //#define Z_IS_TMC26X
-  //#define Z2_IS_TMC26X
-  //#define E0_IS_TMC26X
-  //#define E1_IS_TMC26X
-  //#define E2_IS_TMC26X
-  //#define E3_IS_TMC26X
-  //#define E4_IS_TMC26X
+#if HAS_DRIVER(TMC26X)

  #define X_MAX_CURRENT     1000 // in mA
  #define X_SENSE_RESISTOR    91 // in mOhms
@ -1098,62 +1093,29 @@
  #define E4_SENSE_RESISTOR   91
  #define E4_MICROSTEPS       16

-#endif
+#endif // TMC26X

 // @section tmc_smart

 /**
- * Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
- *
- * You'll also need the TMC2130Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2130Stepper).
- *
 * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
 * the hardware SPI interface on your board and define the required CS pins
 * in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
 * You may also use software SPI if you wish to use general purpose IO pins.
- */
-//#define HAVE_TMC2130
-#if ENABLED(HAVE_TMC2130)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2130
-  //#define X2_IS_TMC2130
-  //#define Y_IS_TMC2130
-  //#define Y2_IS_TMC2130
-  //#define Z_IS_TMC2130
-  //#define Z2_IS_TMC2130
-  //#define E0_IS_TMC2130
-  //#define E1_IS_TMC2130
-  //#define E2_IS_TMC2130
-  //#define E3_IS_TMC2130
-  //#define E4_IS_TMC2130
-#endif
-
-/**
- * Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
- * Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
+ *
+ * The TMC2130Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2130Stepper
+ *
+ * To use TMC2208 stepper UART-configurable stepper drivers
+ * connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
 * To use the reading capabilities, also connect #_SERIAL_RX_PIN
 * to PDN_UART without a resistor.
 * The drivers can also be used with hardware serial.
 *
- * You'll also need the TMC2208Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2208Stepper).
+ * The TMC2208Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2208Stepper
 */
-//#define HAVE_TMC2208
-#if ENABLED(HAVE_TMC2208)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2208
-  //#define X2_IS_TMC2208
-  //#define Y_IS_TMC2208
-  //#define Y2_IS_TMC2208
-  //#define Z_IS_TMC2208
-  //#define Z2_IS_TMC2208
-  //#define E0_IS_TMC2208
-  //#define E1_IS_TMC2208
-  //#define E2_IS_TMC2208
-  //#define E3_IS_TMC2208
-  //#define E4_IS_TMC2208
-#endif
-
-#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
+#if HAS_TRINAMIC

  #define R_SENSE           0.11  // R_sense resistor for SilentStepStick2130
  #define HOLD_MULTIPLIER    0.5  // Scales down the holding current from run current
@ -1308,25 +1270,12 @@
 // @section L6470

 /**
- * Enable this section if you have L6470 motor drivers.
- * You need to import the L6470 library into the Arduino IDE for this.
- * (https://github.com/ameyer/Arduino-L6470)
+ * L6470 Stepper Driver options
+ *
+ * The Arduino-L6470 library is required for this stepper driver.
+ * https://github.com/ameyer/Arduino-L6470
 */
-
-//#define HAVE_L6470DRIVER
-#if ENABLED(HAVE_L6470DRIVER)
-
-  //#define X_IS_L6470
-  //#define X2_IS_L6470
-  //#define Y_IS_L6470
-  //#define Y2_IS_L6470
-  //#define Z_IS_L6470
-  //#define Z2_IS_L6470
-  //#define E0_IS_L6470
-  //#define E1_IS_L6470
-  //#define E2_IS_L6470
-  //#define E3_IS_L6470
-  //#define E4_IS_L6470
+#if HAS_DRIVER(L6470)

  #define X_MICROSTEPS      16 // number of microsteps
  #define X_OVERCURRENT   2000 // maxc current in mA. If the current goes over this value, the driver will switch off
@ -1372,7 +1321,7 @@
  #define E4_OVERCURRENT  2000
  #define E4_STALLCURRENT 1500

-#endif
+#endif // L6470

 /**
 * TWI/I2C BUS
--- a/Marlin/src/config/examples/Creality/Ender-2/Configuration.h
+++ b/Marlin/src/config/examples/Creality/Ender-2/Configuration.h
@ -555,6 +555,29 @@
 #define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
 #define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.

+/**
+ * Specify Stepper Driver types
+ * The options are used to determine driver pulse timings as well as more advanced functionality.
+ * Stepper timing options can be overridden in Configuration_adv.h
+ *
+ * Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
+ *          TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
+ *          TMC26X,  TMC26X_STANDALONE,  TMC2660, TMC2660_STANDALONE,
+ *          TMC5130, TMC5130_STANDALONE
+ * :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
+ */
+#define X_DRIVER_TYPE  A4988
+#define Y_DRIVER_TYPE  A4988
+#define Z_DRIVER_TYPE  A4988
+#define X2_DRIVER_TYPE A4988
+#define Y2_DRIVER_TYPE A4988
+#define Z2_DRIVER_TYPE A4988
+#define E0_DRIVER_TYPE A4988
+#define E1_DRIVER_TYPE A4988
+#define E2_DRIVER_TYPE A4988
+#define E3_DRIVER_TYPE A4988
+#define E4_DRIVER_TYPE A4988
+
 // Enable this feature if all enabled endstop pins are interrupt-capable.
 // This will remove the need to poll the interrupt pins, saving many CPU cycles.
 //#define ENDSTOP_INTERRUPTS_FEATURE
--- a/Marlin/src/config/examples/Creality/Ender-2/Configuration_adv.h
+++ b/Marlin/src/config/examples/Creality/Ender-2/Configuration_adv.h
@ -837,15 +837,17 @@

 /**
 * Minimum delay after setting the stepper DIR (in ns)
- *    0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
- *   20 : Minimum for TMC2xxx drivers
- *  200 : Minimum for A4988 drivers
- *  500 : Minimum for LV8729 drivers (guess, no info in datasheet)
- *  650 : Minimum for DRV8825 drivers
- * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
- *15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *     0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
+ *    20 : Minimum for TMC2xxx drivers
+ *   200 : Minimum for A4988 drivers
+ *   500 : Minimum for LV8729 drivers (guess, no info in datasheet)
+ *   650 : Minimum for DRV8825 drivers
+ *  1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
+ * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_DIR_DELAY 0
+//#define MINIMUM_STEPPER_DIR_DELAY 650

 /**
 * Minimum stepper driver pulse width (in µs)
@ -855,8 +857,10 @@
 *   2 : Minimum for DRV8825 stepper drivers
 *   3 : Minimum for TB6600 stepper drivers
 *  30 : Minimum for TB6560 stepper drivers
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_PULSE 2
+//#define MINIMUM_STEPPER_PULSE 2

 /**
 * Maximum stepping rate (in Hz) the stepper driver allows
@ -867,8 +871,10 @@
 *  150000 : Maximum for TB6600 stepper driver
 *  130000 : Maximum for LV8729 stepper driver
 *   15000 : Maximum for TB6560 stepper driver
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MAXIMUM_STEPPER_RATE 250000
+//#define MAXIMUM_STEPPER_RATE 250000

 // @section temperature

@ -1036,23 +1042,12 @@
 // @section tmc

 /**
- * Enable this section if you have TMC26X motor drivers.
- * You will need to import the TMC26XStepper library into the Arduino IDE for this
- * (https://github.com/trinamic/TMC26XStepper.git)
+ * TMC26X Stepper Driver options
+ *
+ * The TMC26XStepper library is required for this stepper driver.
+ * https://github.com/trinamic/TMC26XStepper
 */
-//#define HAVE_TMC26X
-#if ENABLED(HAVE_TMC26X)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC26X
-  //#define X2_IS_TMC26X
-  //#define Y_IS_TMC26X
-  //#define Y2_IS_TMC26X
-  //#define Z_IS_TMC26X
-  //#define Z2_IS_TMC26X
-  //#define E0_IS_TMC26X
-  //#define E1_IS_TMC26X
-  //#define E2_IS_TMC26X
-  //#define E3_IS_TMC26X
-  //#define E4_IS_TMC26X
+#if HAS_DRIVER(TMC26X)

  #define X_MAX_CURRENT     1000 // in mA
  #define X_SENSE_RESISTOR    91 // in mOhms
@ -1098,62 +1093,29 @@
  #define E4_SENSE_RESISTOR   91
  #define E4_MICROSTEPS       16

-#endif
+#endif // TMC26X

 // @section tmc_smart

 /**
- * Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
- *
- * You'll also need the TMC2130Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2130Stepper).
- *
 * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
 * the hardware SPI interface on your board and define the required CS pins
 * in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
 * You may also use software SPI if you wish to use general purpose IO pins.
- */
-//#define HAVE_TMC2130
-#if ENABLED(HAVE_TMC2130)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2130
-  //#define X2_IS_TMC2130
-  //#define Y_IS_TMC2130
-  //#define Y2_IS_TMC2130
-  //#define Z_IS_TMC2130
-  //#define Z2_IS_TMC2130
-  //#define E0_IS_TMC2130
-  //#define E1_IS_TMC2130
-  //#define E2_IS_TMC2130
-  //#define E3_IS_TMC2130
-  //#define E4_IS_TMC2130
-#endif
-
-/**
- * Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
- * Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
+ *
+ * The TMC2130Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2130Stepper
+ *
+ * To use TMC2208 stepper UART-configurable stepper drivers
+ * connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
 * To use the reading capabilities, also connect #_SERIAL_RX_PIN
 * to PDN_UART without a resistor.
 * The drivers can also be used with hardware serial.
 *
- * You'll also need the TMC2208Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2208Stepper).
+ * The TMC2208Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2208Stepper
 */
-//#define HAVE_TMC2208
-#if ENABLED(HAVE_TMC2208)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2208
-  //#define X2_IS_TMC2208
-  //#define Y_IS_TMC2208
-  //#define Y2_IS_TMC2208
-  //#define Z_IS_TMC2208
-  //#define Z2_IS_TMC2208
-  //#define E0_IS_TMC2208
-  //#define E1_IS_TMC2208
-  //#define E2_IS_TMC2208
-  //#define E3_IS_TMC2208
-  //#define E4_IS_TMC2208
-#endif
-
-#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
+#if HAS_TRINAMIC

  #define R_SENSE           0.11  // R_sense resistor for SilentStepStick2130
  #define HOLD_MULTIPLIER    0.5  // Scales down the holding current from run current
@ -1308,25 +1270,12 @@
 // @section L6470

 /**
- * Enable this section if you have L6470 motor drivers.
- * You need to import the L6470 library into the Arduino IDE for this.
- * (https://github.com/ameyer/Arduino-L6470)
+ * L6470 Stepper Driver options
+ *
+ * The Arduino-L6470 library is required for this stepper driver.
+ * https://github.com/ameyer/Arduino-L6470
 */
-
-//#define HAVE_L6470DRIVER
-#if ENABLED(HAVE_L6470DRIVER)
-
-  //#define X_IS_L6470
-  //#define X2_IS_L6470
-  //#define Y_IS_L6470
-  //#define Y2_IS_L6470
-  //#define Z_IS_L6470
-  //#define Z2_IS_L6470
-  //#define E0_IS_L6470
-  //#define E1_IS_L6470
-  //#define E2_IS_L6470
-  //#define E3_IS_L6470
-  //#define E4_IS_L6470
+#if HAS_DRIVER(L6470)

  #define X_MICROSTEPS      16 // number of microsteps
  #define X_OVERCURRENT   2000 // maxc current in mA. If the current goes over this value, the driver will switch off
@ -1372,7 +1321,7 @@
  #define E4_OVERCURRENT  2000
  #define E4_STALLCURRENT 1500

-#endif
+#endif // L6470

 /**
 * TWI/I2C BUS
--- a/Marlin/src/config/examples/Creality/Ender-3/Configuration.h
+++ b/Marlin/src/config/examples/Creality/Ender-3/Configuration.h
@ -555,6 +555,29 @@
 #define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
 #define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.

+/**
+ * Specify Stepper Driver types
+ * The options are used to determine driver pulse timings as well as more advanced functionality.
+ * Stepper timing options can be overridden in Configuration_adv.h
+ *
+ * Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
+ *          TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
+ *          TMC26X,  TMC26X_STANDALONE,  TMC2660, TMC2660_STANDALONE,
+ *          TMC5130, TMC5130_STANDALONE
+ * :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
+ */
+#define X_DRIVER_TYPE  A4988
+#define Y_DRIVER_TYPE  A4988
+#define Z_DRIVER_TYPE  A4988
+#define X2_DRIVER_TYPE A4988
+#define Y2_DRIVER_TYPE A4988
+#define Z2_DRIVER_TYPE A4988
+#define E0_DRIVER_TYPE A4988
+#define E1_DRIVER_TYPE A4988
+#define E2_DRIVER_TYPE A4988
+#define E3_DRIVER_TYPE A4988
+#define E4_DRIVER_TYPE A4988
+
 // Enable this feature if all enabled endstop pins are interrupt-capable.
 // This will remove the need to poll the interrupt pins, saving many CPU cycles.
 //#define ENDSTOP_INTERRUPTS_FEATURE
--- a/Marlin/src/config/examples/Creality/Ender-3/Configuration_adv.h
+++ b/Marlin/src/config/examples/Creality/Ender-3/Configuration_adv.h
@ -837,15 +837,17 @@

 /**
 * Minimum delay after setting the stepper DIR (in ns)
- *    0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
- *   20 : Minimum for TMC2xxx drivers
- *  200 : Minimum for A4988 drivers
- *  500 : Minimum for LV8729 drivers (guess, no info in datasheet)
- *  650 : Minimum for DRV8825 drivers
- * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
- *15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *     0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
+ *    20 : Minimum for TMC2xxx drivers
+ *   200 : Minimum for A4988 drivers
+ *   500 : Minimum for LV8729 drivers (guess, no info in datasheet)
+ *   650 : Minimum for DRV8825 drivers
+ *  1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
+ * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_DIR_DELAY 0
+//#define MINIMUM_STEPPER_DIR_DELAY 650

 /**
 * Minimum stepper driver pulse width (in µs)
@ -855,8 +857,10 @@
 *   2 : Minimum for DRV8825 stepper drivers
 *   3 : Minimum for TB6600 stepper drivers
 *  30 : Minimum for TB6560 stepper drivers
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_PULSE 2
+//#define MINIMUM_STEPPER_PULSE 2

 /**
 * Maximum stepping rate (in Hz) the stepper driver allows
@ -867,8 +871,10 @@
 *  150000 : Maximum for TB6600 stepper driver
 *  130000 : Maximum for LV8729 stepper driver
 *   15000 : Maximum for TB6560 stepper driver
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MAXIMUM_STEPPER_RATE 250000
+//#define MAXIMUM_STEPPER_RATE 250000

 // @section temperature

@ -1036,23 +1042,12 @@
 // @section tmc

 /**
- * Enable this section if you have TMC26X motor drivers.
- * You will need to import the TMC26XStepper library into the Arduino IDE for this
- * (https://github.com/trinamic/TMC26XStepper.git)
+ * TMC26X Stepper Driver options
+ *
+ * The TMC26XStepper library is required for this stepper driver.
+ * https://github.com/trinamic/TMC26XStepper
 */
-//#define HAVE_TMC26X
-#if ENABLED(HAVE_TMC26X)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC26X
-  //#define X2_IS_TMC26X
-  //#define Y_IS_TMC26X
-  //#define Y2_IS_TMC26X
-  //#define Z_IS_TMC26X
-  //#define Z2_IS_TMC26X
-  //#define E0_IS_TMC26X
-  //#define E1_IS_TMC26X
-  //#define E2_IS_TMC26X
-  //#define E3_IS_TMC26X
-  //#define E4_IS_TMC26X
+#if HAS_DRIVER(TMC26X)

  #define X_MAX_CURRENT     1000 // in mA
  #define X_SENSE_RESISTOR    91 // in mOhms
@ -1098,62 +1093,29 @@
  #define E4_SENSE_RESISTOR   91
  #define E4_MICROSTEPS       16

-#endif
+#endif // TMC26X

 // @section tmc_smart

 /**
- * Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
- *
- * You'll also need the TMC2130Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2130Stepper).
- *
 * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
 * the hardware SPI interface on your board and define the required CS pins
 * in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
 * You may also use software SPI if you wish to use general purpose IO pins.
- */
-//#define HAVE_TMC2130
-#if ENABLED(HAVE_TMC2130)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2130
-  //#define X2_IS_TMC2130
-  //#define Y_IS_TMC2130
-  //#define Y2_IS_TMC2130
-  //#define Z_IS_TMC2130
-  //#define Z2_IS_TMC2130
-  //#define E0_IS_TMC2130
-  //#define E1_IS_TMC2130
-  //#define E2_IS_TMC2130
-  //#define E3_IS_TMC2130
-  //#define E4_IS_TMC2130
-#endif
-
-/**
- * Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
- * Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
+ *
+ * The TMC2130Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2130Stepper
+ *
+ * To use TMC2208 stepper UART-configurable stepper drivers
+ * connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
 * To use the reading capabilities, also connect #_SERIAL_RX_PIN
 * to PDN_UART without a resistor.
 * The drivers can also be used with hardware serial.
 *
- * You'll also need the TMC2208Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2208Stepper).
+ * The TMC2208Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2208Stepper
 */
-//#define HAVE_TMC2208
-#if ENABLED(HAVE_TMC2208)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2208
-  //#define X2_IS_TMC2208
-  //#define Y_IS_TMC2208
-  //#define Y2_IS_TMC2208
-  //#define Z_IS_TMC2208
-  //#define Z2_IS_TMC2208
-  //#define E0_IS_TMC2208
-  //#define E1_IS_TMC2208
-  //#define E2_IS_TMC2208
-  //#define E3_IS_TMC2208
-  //#define E4_IS_TMC2208
-#endif
-
-#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
+#if HAS_TRINAMIC

  #define R_SENSE           0.11  // R_sense resistor for SilentStepStick2130
  #define HOLD_MULTIPLIER    0.5  // Scales down the holding current from run current
@ -1308,25 +1270,12 @@
 // @section L6470

 /**
- * Enable this section if you have L6470 motor drivers.
- * You need to import the L6470 library into the Arduino IDE for this.
- * (https://github.com/ameyer/Arduino-L6470)
+ * L6470 Stepper Driver options
+ *
+ * The Arduino-L6470 library is required for this stepper driver.
+ * https://github.com/ameyer/Arduino-L6470
 */
-
-//#define HAVE_L6470DRIVER
-#if ENABLED(HAVE_L6470DRIVER)
-
-  //#define X_IS_L6470
-  //#define X2_IS_L6470
-  //#define Y_IS_L6470
-  //#define Y2_IS_L6470
-  //#define Z_IS_L6470
-  //#define Z2_IS_L6470
-  //#define E0_IS_L6470
-  //#define E1_IS_L6470
-  //#define E2_IS_L6470
-  //#define E3_IS_L6470
-  //#define E4_IS_L6470
+#if HAS_DRIVER(L6470)

  #define X_MICROSTEPS      16 // number of microsteps
  #define X_OVERCURRENT   2000 // maxc current in mA. If the current goes over this value, the driver will switch off
@ -1372,7 +1321,7 @@
  #define E4_OVERCURRENT  2000
  #define E4_STALLCURRENT 1500

-#endif
+#endif // L6470

 /**
 * TWI/I2C BUS
--- a/Marlin/src/config/examples/Creality/Ender-4/Configuration.h
+++ b/Marlin/src/config/examples/Creality/Ender-4/Configuration.h
@ -561,6 +561,29 @@
 #define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
 #define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.

+/**
+ * Specify Stepper Driver types
+ * The options are used to determine driver pulse timings as well as more advanced functionality.
+ * Stepper timing options can be overridden in Configuration_adv.h
+ *
+ * Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
+ *          TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
+ *          TMC26X,  TMC26X_STANDALONE,  TMC2660, TMC2660_STANDALONE,
+ *          TMC5130, TMC5130_STANDALONE
+ * :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
+ */
+#define X_DRIVER_TYPE  A4988
+#define Y_DRIVER_TYPE  A4988
+#define Z_DRIVER_TYPE  A4988
+#define X2_DRIVER_TYPE A4988
+#define Y2_DRIVER_TYPE A4988
+#define Z2_DRIVER_TYPE A4988
+#define E0_DRIVER_TYPE A4988
+#define E1_DRIVER_TYPE A4988
+#define E2_DRIVER_TYPE A4988
+#define E3_DRIVER_TYPE A4988
+#define E4_DRIVER_TYPE A4988
+
 // Enable this feature if all enabled endstop pins are interrupt-capable.
 // This will remove the need to poll the interrupt pins, saving many CPU cycles.
 //#define ENDSTOP_INTERRUPTS_FEATURE
--- a/Marlin/src/config/examples/Creality/Ender-4/Configuration_adv.h
+++ b/Marlin/src/config/examples/Creality/Ender-4/Configuration_adv.h
@ -837,15 +837,17 @@

 /**
 * Minimum delay after setting the stepper DIR (in ns)
- *    0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
- *   20 : Minimum for TMC2xxx drivers
- *  200 : Minimum for A4988 drivers
- *  500 : Minimum for LV8729 drivers (guess, no info in datasheet)
- *  650 : Minimum for DRV8825 drivers
- * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
- *15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *     0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
+ *    20 : Minimum for TMC2xxx drivers
+ *   200 : Minimum for A4988 drivers
+ *   500 : Minimum for LV8729 drivers (guess, no info in datasheet)
+ *   650 : Minimum for DRV8825 drivers
+ *  1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
+ * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_DIR_DELAY 0
+//#define MINIMUM_STEPPER_DIR_DELAY 650

 /**
 * Minimum stepper driver pulse width (in µs)
@ -855,8 +857,10 @@
 *   2 : Minimum for DRV8825 stepper drivers
 *   3 : Minimum for TB6600 stepper drivers
 *  30 : Minimum for TB6560 stepper drivers
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_PULSE 2
+//#define MINIMUM_STEPPER_PULSE 2

 /**
 * Maximum stepping rate (in Hz) the stepper driver allows
@ -867,8 +871,10 @@
 *  150000 : Maximum for TB6600 stepper driver
 *  130000 : Maximum for LV8729 stepper driver
 *   15000 : Maximum for TB6560 stepper driver
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MAXIMUM_STEPPER_RATE 250000
+//#define MAXIMUM_STEPPER_RATE 250000

 // @section temperature

@ -1036,23 +1042,12 @@
 // @section tmc

 /**
- * Enable this section if you have TMC26X motor drivers.
- * You will need to import the TMC26XStepper library into the Arduino IDE for this
- * (https://github.com/trinamic/TMC26XStepper.git)
+ * TMC26X Stepper Driver options
+ *
+ * The TMC26XStepper library is required for this stepper driver.
+ * https://github.com/trinamic/TMC26XStepper
 */
-//#define HAVE_TMC26X
-#if ENABLED(HAVE_TMC26X)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC26X
-  //#define X2_IS_TMC26X
-  //#define Y_IS_TMC26X
-  //#define Y2_IS_TMC26X
-  //#define Z_IS_TMC26X
-  //#define Z2_IS_TMC26X
-  //#define E0_IS_TMC26X
-  //#define E1_IS_TMC26X
-  //#define E2_IS_TMC26X
-  //#define E3_IS_TMC26X
-  //#define E4_IS_TMC26X
+#if HAS_DRIVER(TMC26X)

  #define X_MAX_CURRENT     1000 // in mA
  #define X_SENSE_RESISTOR    91 // in mOhms
@ -1098,62 +1093,29 @@
  #define E4_SENSE_RESISTOR   91
  #define E4_MICROSTEPS       16

-#endif
+#endif // TMC26X

 // @section tmc_smart

 /**
- * Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
- *
- * You'll also need the TMC2130Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2130Stepper).
- *
 * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
 * the hardware SPI interface on your board and define the required CS pins
 * in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
 * You may also use software SPI if you wish to use general purpose IO pins.
- */
-//#define HAVE_TMC2130
-#if ENABLED(HAVE_TMC2130)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2130
-  //#define X2_IS_TMC2130
-  //#define Y_IS_TMC2130
-  //#define Y2_IS_TMC2130
-  //#define Z_IS_TMC2130
-  //#define Z2_IS_TMC2130
-  //#define E0_IS_TMC2130
-  //#define E1_IS_TMC2130
-  //#define E2_IS_TMC2130
-  //#define E3_IS_TMC2130
-  //#define E4_IS_TMC2130
-#endif
-
-/**
- * Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
- * Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
+ *
+ * The TMC2130Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2130Stepper
+ *
+ * To use TMC2208 stepper UART-configurable stepper drivers
+ * connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
 * To use the reading capabilities, also connect #_SERIAL_RX_PIN
 * to PDN_UART without a resistor.
 * The drivers can also be used with hardware serial.
 *
- * You'll also need the TMC2208Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2208Stepper).
+ * The TMC2208Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2208Stepper
 */
-//#define HAVE_TMC2208
-#if ENABLED(HAVE_TMC2208)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2208
-  //#define X2_IS_TMC2208
-  //#define Y_IS_TMC2208
-  //#define Y2_IS_TMC2208
-  //#define Z_IS_TMC2208
-  //#define Z2_IS_TMC2208
-  //#define E0_IS_TMC2208
-  //#define E1_IS_TMC2208
-  //#define E2_IS_TMC2208
-  //#define E3_IS_TMC2208
-  //#define E4_IS_TMC2208
-#endif
-
-#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
+#if HAS_TRINAMIC

  #define R_SENSE           0.11  // R_sense resistor for SilentStepStick2130
  #define HOLD_MULTIPLIER    0.5  // Scales down the holding current from run current
@ -1308,25 +1270,12 @@
 // @section L6470

 /**
- * Enable this section if you have L6470 motor drivers.
- * You need to import the L6470 library into the Arduino IDE for this.
- * (https://github.com/ameyer/Arduino-L6470)
+ * L6470 Stepper Driver options
+ *
+ * The Arduino-L6470 library is required for this stepper driver.
+ * https://github.com/ameyer/Arduino-L6470
 */
-
-//#define HAVE_L6470DRIVER
-#if ENABLED(HAVE_L6470DRIVER)
-
-  //#define X_IS_L6470
-  //#define X2_IS_L6470
-  //#define Y_IS_L6470
-  //#define Y2_IS_L6470
-  //#define Z_IS_L6470
-  //#define Z2_IS_L6470
-  //#define E0_IS_L6470
-  //#define E1_IS_L6470
-  //#define E2_IS_L6470
-  //#define E3_IS_L6470
-  //#define E4_IS_L6470
+#if HAS_DRIVER(L6470)

  #define X_MICROSTEPS      16 // number of microsteps
  #define X_OVERCURRENT   2000 // maxc current in mA. If the current goes over this value, the driver will switch off
@ -1372,7 +1321,7 @@
  #define E4_OVERCURRENT  2000
  #define E4_STALLCURRENT 1500

-#endif
+#endif // L6470

 /**
 * TWI/I2C BUS
--- a/Marlin/src/config/examples/Felix/Configuration.h
+++ b/Marlin/src/config/examples/Felix/Configuration.h
@ -532,6 +532,29 @@
 #define Z_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
 #define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.

+/**
+ * Specify Stepper Driver types
+ * The options are used to determine driver pulse timings as well as more advanced functionality.
+ * Stepper timing options can be overridden in Configuration_adv.h
+ *
+ * Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
+ *          TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
+ *          TMC26X,  TMC26X_STANDALONE,  TMC2660, TMC2660_STANDALONE,
+ *          TMC5130, TMC5130_STANDALONE
+ * :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
+ */
+#define X_DRIVER_TYPE  A4988
+#define Y_DRIVER_TYPE  A4988
+#define Z_DRIVER_TYPE  A4988
+#define X2_DRIVER_TYPE A4988
+#define Y2_DRIVER_TYPE A4988
+#define Z2_DRIVER_TYPE A4988
+#define E0_DRIVER_TYPE A4988
+#define E1_DRIVER_TYPE A4988
+#define E2_DRIVER_TYPE A4988
+#define E3_DRIVER_TYPE A4988
+#define E4_DRIVER_TYPE A4988
+
 // Enable this feature if all enabled endstop pins are interrupt-capable.
 // This will remove the need to poll the interrupt pins, saving many CPU cycles.
 //#define ENDSTOP_INTERRUPTS_FEATURE
--- a/Marlin/src/config/examples/Felix/Configuration_adv.h
+++ b/Marlin/src/config/examples/Felix/Configuration_adv.h
@ -837,15 +837,17 @@

 /**
 * Minimum delay after setting the stepper DIR (in ns)
- *    0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
- *   20 : Minimum for TMC2xxx drivers
- *  200 : Minimum for A4988 drivers
- *  500 : Minimum for LV8729 drivers (guess, no info in datasheet)
- *  650 : Minimum for DRV8825 drivers
- * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
- *15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *     0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
+ *    20 : Minimum for TMC2xxx drivers
+ *   200 : Minimum for A4988 drivers
+ *   500 : Minimum for LV8729 drivers (guess, no info in datasheet)
+ *   650 : Minimum for DRV8825 drivers
+ *  1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
+ * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_DIR_DELAY 0
+//#define MINIMUM_STEPPER_DIR_DELAY 650

 /**
 * Minimum stepper driver pulse width (in µs)
@ -855,8 +857,10 @@
 *   2 : Minimum for DRV8825 stepper drivers
 *   3 : Minimum for TB6600 stepper drivers
 *  30 : Minimum for TB6560 stepper drivers
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_PULSE 2
+//#define MINIMUM_STEPPER_PULSE 2

 /**
 * Maximum stepping rate (in Hz) the stepper driver allows
@ -867,8 +871,10 @@
 *  150000 : Maximum for TB6600 stepper driver
 *  130000 : Maximum for LV8729 stepper driver
 *   15000 : Maximum for TB6560 stepper driver
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MAXIMUM_STEPPER_RATE 250000
+//#define MAXIMUM_STEPPER_RATE 250000

 // @section temperature

@ -1036,23 +1042,12 @@
 // @section tmc

 /**
- * Enable this section if you have TMC26X motor drivers.
- * You will need to import the TMC26XStepper library into the Arduino IDE for this
- * (https://github.com/trinamic/TMC26XStepper.git)
+ * TMC26X Stepper Driver options
+ *
+ * The TMC26XStepper library is required for this stepper driver.
+ * https://github.com/trinamic/TMC26XStepper
 */
-//#define HAVE_TMC26X
-#if ENABLED(HAVE_TMC26X)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC26X
-  //#define X2_IS_TMC26X
-  //#define Y_IS_TMC26X
-  //#define Y2_IS_TMC26X
-  //#define Z_IS_TMC26X
-  //#define Z2_IS_TMC26X
-  //#define E0_IS_TMC26X
-  //#define E1_IS_TMC26X
-  //#define E2_IS_TMC26X
-  //#define E3_IS_TMC26X
-  //#define E4_IS_TMC26X
+#if HAS_DRIVER(TMC26X)

  #define X_MAX_CURRENT     1000 // in mA
  #define X_SENSE_RESISTOR    91 // in mOhms
@ -1098,62 +1093,29 @@
  #define E4_SENSE_RESISTOR   91
  #define E4_MICROSTEPS       16

-#endif
+#endif // TMC26X

 // @section tmc_smart

 /**
- * Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
- *
- * You'll also need the TMC2130Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2130Stepper).
- *
 * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
 * the hardware SPI interface on your board and define the required CS pins
 * in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
 * You may also use software SPI if you wish to use general purpose IO pins.
- */
-//#define HAVE_TMC2130
-#if ENABLED(HAVE_TMC2130)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2130
-  //#define X2_IS_TMC2130
-  //#define Y_IS_TMC2130
-  //#define Y2_IS_TMC2130
-  //#define Z_IS_TMC2130
-  //#define Z2_IS_TMC2130
-  //#define E0_IS_TMC2130
-  //#define E1_IS_TMC2130
-  //#define E2_IS_TMC2130
-  //#define E3_IS_TMC2130
-  //#define E4_IS_TMC2130
-#endif
-
-/**
- * Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
- * Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
+ *
+ * The TMC2130Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2130Stepper
+ *
+ * To use TMC2208 stepper UART-configurable stepper drivers
+ * connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
 * To use the reading capabilities, also connect #_SERIAL_RX_PIN
 * to PDN_UART without a resistor.
 * The drivers can also be used with hardware serial.
 *
- * You'll also need the TMC2208Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2208Stepper).
+ * The TMC2208Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2208Stepper
 */
-//#define HAVE_TMC2208
-#if ENABLED(HAVE_TMC2208)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2208
-  //#define X2_IS_TMC2208
-  //#define Y_IS_TMC2208
-  //#define Y2_IS_TMC2208
-  //#define Z_IS_TMC2208
-  //#define Z2_IS_TMC2208
-  //#define E0_IS_TMC2208
-  //#define E1_IS_TMC2208
-  //#define E2_IS_TMC2208
-  //#define E3_IS_TMC2208
-  //#define E4_IS_TMC2208
-#endif
-
-#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
+#if HAS_TRINAMIC

  #define R_SENSE           0.11  // R_sense resistor for SilentStepStick2130
  #define HOLD_MULTIPLIER    0.5  // Scales down the holding current from run current
@ -1308,25 +1270,12 @@
 // @section L6470

 /**
- * Enable this section if you have L6470 motor drivers.
- * You need to import the L6470 library into the Arduino IDE for this.
- * (https://github.com/ameyer/Arduino-L6470)
+ * L6470 Stepper Driver options
+ *
+ * The Arduino-L6470 library is required for this stepper driver.
+ * https://github.com/ameyer/Arduino-L6470
 */
-
-//#define HAVE_L6470DRIVER
-#if ENABLED(HAVE_L6470DRIVER)
-
-  //#define X_IS_L6470
-  //#define X2_IS_L6470
-  //#define Y_IS_L6470
-  //#define Y2_IS_L6470
-  //#define Z_IS_L6470
-  //#define Z2_IS_L6470
-  //#define E0_IS_L6470
-  //#define E1_IS_L6470
-  //#define E2_IS_L6470
-  //#define E3_IS_L6470
-  //#define E4_IS_L6470
+#if HAS_DRIVER(L6470)

  #define X_MICROSTEPS      16 // number of microsteps
  #define X_OVERCURRENT   2000 // maxc current in mA. If the current goes over this value, the driver will switch off
@ -1372,7 +1321,7 @@
  #define E4_OVERCURRENT  2000
  #define E4_STALLCURRENT 1500

-#endif
+#endif // L6470

 /**
 * TWI/I2C BUS
--- a/Marlin/src/config/examples/Felix/DUAL/Configuration.h
+++ b/Marlin/src/config/examples/Felix/DUAL/Configuration.h
@ -532,6 +532,29 @@
 #define Z_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
 #define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.

+/**
+ * Specify Stepper Driver types
+ * The options are used to determine driver pulse timings as well as more advanced functionality.
+ * Stepper timing options can be overridden in Configuration_adv.h
+ *
+ * Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
+ *          TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
+ *          TMC26X,  TMC26X_STANDALONE,  TMC2660, TMC2660_STANDALONE,
+ *          TMC5130, TMC5130_STANDALONE
+ * :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
+ */
+#define X_DRIVER_TYPE  A4988
+#define Y_DRIVER_TYPE  A4988
+#define Z_DRIVER_TYPE  A4988
+#define X2_DRIVER_TYPE A4988
+#define Y2_DRIVER_TYPE A4988
+#define Z2_DRIVER_TYPE A4988
+#define E0_DRIVER_TYPE A4988
+#define E1_DRIVER_TYPE A4988
+#define E2_DRIVER_TYPE A4988
+#define E3_DRIVER_TYPE A4988
+#define E4_DRIVER_TYPE A4988
+
 // Enable this feature if all enabled endstop pins are interrupt-capable.
 // This will remove the need to poll the interrupt pins, saving many CPU cycles.
 //#define ENDSTOP_INTERRUPTS_FEATURE
--- a/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration_adv.h
+++ b/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration_adv.h
@ -837,15 +837,17 @@

 /**
 * Minimum delay after setting the stepper DIR (in ns)
- *    0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
- *   20 : Minimum for TMC2xxx drivers
- *  200 : Minimum for A4988 drivers
- *  500 : Minimum for LV8729 drivers (guess, no info in datasheet)
- *  650 : Minimum for DRV8825 drivers
- * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
- *15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *     0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
+ *    20 : Minimum for TMC2xxx drivers
+ *   200 : Minimum for A4988 drivers
+ *   500 : Minimum for LV8729 drivers (guess, no info in datasheet)
+ *   650 : Minimum for DRV8825 drivers
+ *  1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
+ * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_DIR_DELAY 0
+//#define MINIMUM_STEPPER_DIR_DELAY 650

 /**
 * Minimum stepper driver pulse width (in µs)
@ -855,8 +857,10 @@
 *   2 : Minimum for DRV8825 stepper drivers
 *   3 : Minimum for TB6600 stepper drivers
 *  30 : Minimum for TB6560 stepper drivers
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_PULSE 2
+//#define MINIMUM_STEPPER_PULSE 2

 /**
 * Maximum stepping rate (in Hz) the stepper driver allows
@ -867,8 +871,10 @@
 *  150000 : Maximum for TB6600 stepper driver
 *  130000 : Maximum for LV8729 stepper driver
 *   15000 : Maximum for TB6560 stepper driver
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MAXIMUM_STEPPER_RATE 250000
+//#define MAXIMUM_STEPPER_RATE 250000

 // @section temperature

@ -1036,23 +1042,12 @@
 // @section tmc

 /**
- * Enable this section if you have TMC26X motor drivers.
- * You will need to import the TMC26XStepper library into the Arduino IDE for this
- * (https://github.com/trinamic/TMC26XStepper.git)
+ * TMC26X Stepper Driver options
+ *
+ * The TMC26XStepper library is required for this stepper driver.
+ * https://github.com/trinamic/TMC26XStepper
 */
-//#define HAVE_TMC26X
-#if ENABLED(HAVE_TMC26X)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC26X
-  //#define X2_IS_TMC26X
-  //#define Y_IS_TMC26X
-  //#define Y2_IS_TMC26X
-  //#define Z_IS_TMC26X
-  //#define Z2_IS_TMC26X
-  //#define E0_IS_TMC26X
-  //#define E1_IS_TMC26X
-  //#define E2_IS_TMC26X
-  //#define E3_IS_TMC26X
-  //#define E4_IS_TMC26X
+#if HAS_DRIVER(TMC26X)

  #define X_MAX_CURRENT     1000 // in mA
  #define X_SENSE_RESISTOR    91 // in mOhms
@ -1098,62 +1093,29 @@
  #define E4_SENSE_RESISTOR   91
  #define E4_MICROSTEPS       16

-#endif
+#endif // TMC26X

 // @section tmc_smart

 /**
- * Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
- *
- * You'll also need the TMC2130Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2130Stepper).
- *
 * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
 * the hardware SPI interface on your board and define the required CS pins
 * in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
 * You may also use software SPI if you wish to use general purpose IO pins.
- */
-//#define HAVE_TMC2130
-#if ENABLED(HAVE_TMC2130)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2130
-  //#define X2_IS_TMC2130
-  //#define Y_IS_TMC2130
-  //#define Y2_IS_TMC2130
-  //#define Z_IS_TMC2130
-  //#define Z2_IS_TMC2130
-  //#define E0_IS_TMC2130
-  //#define E1_IS_TMC2130
-  //#define E2_IS_TMC2130
-  //#define E3_IS_TMC2130
-  //#define E4_IS_TMC2130
-#endif
-
-/**
- * Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
- * Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
+ *
+ * The TMC2130Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2130Stepper
+ *
+ * To use TMC2208 stepper UART-configurable stepper drivers
+ * connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
 * To use the reading capabilities, also connect #_SERIAL_RX_PIN
 * to PDN_UART without a resistor.
 * The drivers can also be used with hardware serial.
 *
- * You'll also need the TMC2208Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2208Stepper).
+ * The TMC2208Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2208Stepper
 */
-//#define HAVE_TMC2208
-#if ENABLED(HAVE_TMC2208)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2208
-  //#define X2_IS_TMC2208
-  //#define Y_IS_TMC2208
-  //#define Y2_IS_TMC2208
-  //#define Z_IS_TMC2208
-  //#define Z2_IS_TMC2208
-  //#define E0_IS_TMC2208
-  //#define E1_IS_TMC2208
-  //#define E2_IS_TMC2208
-  //#define E3_IS_TMC2208
-  //#define E4_IS_TMC2208
-#endif
-
-#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
+#if HAS_TRINAMIC

  #define R_SENSE           0.11  // R_sense resistor for SilentStepStick2130
  #define HOLD_MULTIPLIER    0.5  // Scales down the holding current from run current
@ -1308,25 +1270,12 @@
 // @section L6470

 /**
- * Enable this section if you have L6470 motor drivers.
- * You need to import the L6470 library into the Arduino IDE for this.
- * (https://github.com/ameyer/Arduino-L6470)
+ * L6470 Stepper Driver options
+ *
+ * The Arduino-L6470 library is required for this stepper driver.
+ * https://github.com/ameyer/Arduino-L6470
 */
-
-//#define HAVE_L6470DRIVER
-#if ENABLED(HAVE_L6470DRIVER)
-
-  //#define X_IS_L6470
-  //#define X2_IS_L6470
-  //#define Y_IS_L6470
-  //#define Y2_IS_L6470
-  //#define Z_IS_L6470
-  //#define Z2_IS_L6470
-  //#define E0_IS_L6470
-  //#define E1_IS_L6470
-  //#define E2_IS_L6470
-  //#define E3_IS_L6470
-  //#define E4_IS_L6470
+#if HAS_DRIVER(L6470)

  #define X_MICROSTEPS      16 // number of microsteps
  #define X_OVERCURRENT   2000 // maxc current in mA. If the current goes over this value, the driver will switch off
@ -1372,7 +1321,7 @@
  #define E4_OVERCURRENT  2000
  #define E4_STALLCURRENT 1500

-#endif
+#endif // L6470

 /**
 * TWI/I2C BUS
--- a/Marlin/src/config/examples/Geeetech/GT2560/Configuration.h
+++ b/Marlin/src/config/examples/Geeetech/GT2560/Configuration.h
@ -566,6 +566,29 @@
 #define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
 #define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.

+/**
+ * Specify Stepper Driver types
+ * The options are used to determine driver pulse timings as well as more advanced functionality.
+ * Stepper timing options can be overridden in Configuration_adv.h
+ *
+ * Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
+ *          TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
+ *          TMC26X,  TMC26X_STANDALONE,  TMC2660, TMC2660_STANDALONE,
+ *          TMC5130, TMC5130_STANDALONE
+ * :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
+ */
+#define X_DRIVER_TYPE  A4988
+#define Y_DRIVER_TYPE  A4988
+#define Z_DRIVER_TYPE  A4988
+#define X2_DRIVER_TYPE A4988
+#define Y2_DRIVER_TYPE A4988
+#define Z2_DRIVER_TYPE A4988
+#define E0_DRIVER_TYPE A4988
+#define E1_DRIVER_TYPE A4988
+#define E2_DRIVER_TYPE A4988
+#define E3_DRIVER_TYPE A4988
+#define E4_DRIVER_TYPE A4988
+
 // Enable this feature if all enabled endstop pins are interrupt-capable.
 // This will remove the need to poll the interrupt pins, saving many CPU cycles.
 //#define ENDSTOP_INTERRUPTS_FEATURE
--- a/Marlin/src/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h
+++ b/Marlin/src/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h
@ -551,6 +551,29 @@
 #define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
 #define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.

+/**
+ * Specify Stepper Driver types
+ * The options are used to determine driver pulse timings as well as more advanced functionality.
+ * Stepper timing options can be overridden in Configuration_adv.h
+ *
+ * Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
+ *          TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
+ *          TMC26X,  TMC26X_STANDALONE,  TMC2660, TMC2660_STANDALONE,
+ *          TMC5130, TMC5130_STANDALONE
+ * :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
+ */
+#define X_DRIVER_TYPE  A4988
+#define Y_DRIVER_TYPE  A4988
+#define Z_DRIVER_TYPE  A4988
+#define X2_DRIVER_TYPE A4988
+#define Y2_DRIVER_TYPE A4988
+#define Z2_DRIVER_TYPE A4988
+#define E0_DRIVER_TYPE A4988
+#define E1_DRIVER_TYPE A4988
+#define E2_DRIVER_TYPE A4988
+#define E3_DRIVER_TYPE A4988
+#define E4_DRIVER_TYPE A4988
+
 // Enable this feature if all enabled endstop pins are interrupt-capable.
 // This will remove the need to poll the interrupt pins, saving many CPU cycles.
 //#define ENDSTOP_INTERRUPTS_FEATURE
--- a/Marlin/src/config/examples/Geeetech/Prusa
+++ b/Marlin/src/config/examples/Geeetech/Prusa
@ -566,6 +566,29 @@
 #define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
 #define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.

+/**
+ * Specify Stepper Driver types
+ * The options are used to determine driver pulse timings as well as more advanced functionality.
+ * Stepper timing options can be overridden in Configuration_adv.h
+ *
+ * Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
+ *          TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
+ *          TMC26X,  TMC26X_STANDALONE,  TMC2660, TMC2660_STANDALONE,
+ *          TMC5130, TMC5130_STANDALONE
+ * :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
+ */
+#define X_DRIVER_TYPE  A4988
+#define Y_DRIVER_TYPE  A4988
+#define Z_DRIVER_TYPE  A4988
+#define X2_DRIVER_TYPE A4988
+#define Y2_DRIVER_TYPE A4988
+#define Z2_DRIVER_TYPE A4988
+#define E0_DRIVER_TYPE A4988
+#define E1_DRIVER_TYPE A4988
+#define E2_DRIVER_TYPE A4988
+#define E3_DRIVER_TYPE A4988
+#define E4_DRIVER_TYPE A4988
+
 // Enable this feature if all enabled endstop pins are interrupt-capable.
 // This will remove the need to poll the interrupt pins, saving many CPU cycles.
 //#define ENDSTOP_INTERRUPTS_FEATURE
--- a/Marlin/src/config/examples/Geeetech/Prusa
+++ b/Marlin/src/config/examples/Geeetech/Prusa
@ -566,6 +566,29 @@
 #define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
 #define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.

+/**
+ * Specify Stepper Driver types
+ * The options are used to determine driver pulse timings as well as more advanced functionality.
+ * Stepper timing options can be overridden in Configuration_adv.h
+ *
+ * Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
+ *          TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
+ *          TMC26X,  TMC26X_STANDALONE,  TMC2660, TMC2660_STANDALONE,
+ *          TMC5130, TMC5130_STANDALONE
+ * :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
+ */
+#define X_DRIVER_TYPE  A4988
+#define Y_DRIVER_TYPE  A4988
+#define Z_DRIVER_TYPE  A4988
+#define X2_DRIVER_TYPE A4988
+#define Y2_DRIVER_TYPE A4988
+#define Z2_DRIVER_TYPE A4988
+#define E0_DRIVER_TYPE A4988
+#define E1_DRIVER_TYPE A4988
+#define E2_DRIVER_TYPE A4988
+#define E3_DRIVER_TYPE A4988
+#define E4_DRIVER_TYPE A4988
+
 // Enable this feature if all enabled endstop pins are interrupt-capable.
 // This will remove the need to poll the interrupt pins, saving many CPU cycles.
 //#define ENDSTOP_INTERRUPTS_FEATURE
--- a/Marlin/src/config/examples/Geeetech/Prusa
+++ b/Marlin/src/config/examples/Geeetech/Prusa
@ -551,6 +551,29 @@
 #define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
 #define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.

+/**
+ * Specify Stepper Driver types
+ * The options are used to determine driver pulse timings as well as more advanced functionality.
+ * Stepper timing options can be overridden in Configuration_adv.h
+ *
+ * Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
+ *          TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
+ *          TMC26X,  TMC26X_STANDALONE,  TMC2660, TMC2660_STANDALONE,
+ *          TMC5130, TMC5130_STANDALONE
+ * :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
+ */
+#define X_DRIVER_TYPE  A4988
+#define Y_DRIVER_TYPE  A4988
+#define Z_DRIVER_TYPE  A4988
+#define X2_DRIVER_TYPE A4988
+#define Y2_DRIVER_TYPE A4988
+#define Z2_DRIVER_TYPE A4988
+#define E0_DRIVER_TYPE A4988
+#define E1_DRIVER_TYPE A4988
+#define E2_DRIVER_TYPE A4988
+#define E3_DRIVER_TYPE A4988
+#define E4_DRIVER_TYPE A4988
+
 // Enable this feature if all enabled endstop pins are interrupt-capable.
 // This will remove the need to poll the interrupt pins, saving many CPU cycles.
 //#define ENDSTOP_INTERRUPTS_FEATURE
--- a/Marlin/src/config/examples/Geeetech/Prusa
+++ b/Marlin/src/config/examples/Geeetech/Prusa
@ -837,15 +837,17 @@

 /**
 * Minimum delay after setting the stepper DIR (in ns)
- *    0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
- *   20 : Minimum for TMC2xxx drivers
- *  200 : Minimum for A4988 drivers
- *  500 : Minimum for LV8729 drivers (guess, no info in datasheet)
- *  650 : Minimum for DRV8825 drivers
- * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
- *15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *     0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
+ *    20 : Minimum for TMC2xxx drivers
+ *   200 : Minimum for A4988 drivers
+ *   500 : Minimum for LV8729 drivers (guess, no info in datasheet)
+ *   650 : Minimum for DRV8825 drivers
+ *  1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
+ * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_DIR_DELAY 0
+//#define MINIMUM_STEPPER_DIR_DELAY 650

 /**
 * Minimum stepper driver pulse width (in µs)
@ -855,8 +857,10 @@
 *   2 : Minimum for DRV8825 stepper drivers
 *   3 : Minimum for TB6600 stepper drivers
 *  30 : Minimum for TB6560 stepper drivers
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_PULSE 2
+//#define MINIMUM_STEPPER_PULSE 2

 /**
 * Maximum stepping rate (in Hz) the stepper driver allows
@ -867,8 +871,10 @@
 *  150000 : Maximum for TB6600 stepper driver
 *  130000 : Maximum for LV8729 stepper driver
 *   15000 : Maximum for TB6560 stepper driver
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MAXIMUM_STEPPER_RATE 250000
+//#define MAXIMUM_STEPPER_RATE 250000

 // @section temperature

@ -1036,23 +1042,12 @@
 // @section tmc

 /**
- * Enable this section if you have TMC26X motor drivers.
- * You will need to import the TMC26XStepper library into the Arduino IDE for this
- * (https://github.com/trinamic/TMC26XStepper.git)
+ * TMC26X Stepper Driver options
+ *
+ * The TMC26XStepper library is required for this stepper driver.
+ * https://github.com/trinamic/TMC26XStepper
 */
-//#define HAVE_TMC26X
-#if ENABLED(HAVE_TMC26X)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC26X
-  //#define X2_IS_TMC26X
-  //#define Y_IS_TMC26X
-  //#define Y2_IS_TMC26X
-  //#define Z_IS_TMC26X
-  //#define Z2_IS_TMC26X
-  //#define E0_IS_TMC26X
-  //#define E1_IS_TMC26X
-  //#define E2_IS_TMC26X
-  //#define E3_IS_TMC26X
-  //#define E4_IS_TMC26X
+#if HAS_DRIVER(TMC26X)

  #define X_MAX_CURRENT     1000 // in mA
  #define X_SENSE_RESISTOR    91 // in mOhms
@ -1098,62 +1093,29 @@
  #define E4_SENSE_RESISTOR   91
  #define E4_MICROSTEPS       16

-#endif
+#endif // TMC26X

 // @section tmc_smart

 /**
- * Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
- *
- * You'll also need the TMC2130Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2130Stepper).
- *
 * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
 * the hardware SPI interface on your board and define the required CS pins
 * in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
 * You may also use software SPI if you wish to use general purpose IO pins.
- */
-//#define HAVE_TMC2130
-#if ENABLED(HAVE_TMC2130)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2130
-  //#define X2_IS_TMC2130
-  //#define Y_IS_TMC2130
-  //#define Y2_IS_TMC2130
-  //#define Z_IS_TMC2130
-  //#define Z2_IS_TMC2130
-  //#define E0_IS_TMC2130
-  //#define E1_IS_TMC2130
-  //#define E2_IS_TMC2130
-  //#define E3_IS_TMC2130
-  //#define E4_IS_TMC2130
-#endif
-
-/**
- * Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
- * Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
+ *
+ * The TMC2130Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2130Stepper
+ *
+ * To use TMC2208 stepper UART-configurable stepper drivers
+ * connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
 * To use the reading capabilities, also connect #_SERIAL_RX_PIN
 * to PDN_UART without a resistor.
 * The drivers can also be used with hardware serial.
 *
- * You'll also need the TMC2208Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2208Stepper).
+ * The TMC2208Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2208Stepper
 */
-//#define HAVE_TMC2208
-#if ENABLED(HAVE_TMC2208)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2208
-  //#define X2_IS_TMC2208
-  //#define Y_IS_TMC2208
-  //#define Y2_IS_TMC2208
-  //#define Z_IS_TMC2208
-  //#define Z2_IS_TMC2208
-  //#define E0_IS_TMC2208
-  //#define E1_IS_TMC2208
-  //#define E2_IS_TMC2208
-  //#define E3_IS_TMC2208
-  //#define E4_IS_TMC2208
-#endif
-
-#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
+#if HAS_TRINAMIC

  #define R_SENSE           0.11  // R_sense resistor for SilentStepStick2130
  #define HOLD_MULTIPLIER    0.5  // Scales down the holding current from run current
@ -1308,25 +1270,12 @@
 // @section L6470

 /**
- * Enable this section if you have L6470 motor drivers.
- * You need to import the L6470 library into the Arduino IDE for this.
- * (https://github.com/ameyer/Arduino-L6470)
+ * L6470 Stepper Driver options
+ *
+ * The Arduino-L6470 library is required for this stepper driver.
+ * https://github.com/ameyer/Arduino-L6470
 */
-
-//#define HAVE_L6470DRIVER
-#if ENABLED(HAVE_L6470DRIVER)
-
-  //#define X_IS_L6470
-  //#define X2_IS_L6470
-  //#define Y_IS_L6470
-  //#define Y2_IS_L6470
-  //#define Z_IS_L6470
-  //#define Z2_IS_L6470
-  //#define E0_IS_L6470
-  //#define E1_IS_L6470
-  //#define E2_IS_L6470
-  //#define E3_IS_L6470
-  //#define E4_IS_L6470
+#if HAS_DRIVER(L6470)

  #define X_MICROSTEPS      16 // number of microsteps
  #define X_OVERCURRENT   2000 // maxc current in mA. If the current goes over this value, the driver will switch off
@ -1372,7 +1321,7 @@
  #define E4_OVERCURRENT  2000
  #define E4_STALLCURRENT 1500

-#endif
+#endif // L6470

 /**
 * TWI/I2C BUS
--- a/Marlin/src/config/examples/Geeetech/Prusa
+++ b/Marlin/src/config/examples/Geeetech/Prusa
@ -551,6 +551,29 @@
 #define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
 #define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.

+/**
+ * Specify Stepper Driver types
+ * The options are used to determine driver pulse timings as well as more advanced functionality.
+ * Stepper timing options can be overridden in Configuration_adv.h
+ *
+ * Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
+ *          TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
+ *          TMC26X,  TMC26X_STANDALONE,  TMC2660, TMC2660_STANDALONE,
+ *          TMC5130, TMC5130_STANDALONE
+ * :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
+ */
+#define X_DRIVER_TYPE  A4988
+#define Y_DRIVER_TYPE  A4988
+#define Z_DRIVER_TYPE  A4988
+#define X2_DRIVER_TYPE A4988
+#define Y2_DRIVER_TYPE A4988
+#define Z2_DRIVER_TYPE A4988
+#define E0_DRIVER_TYPE A4988
+#define E1_DRIVER_TYPE A4988
+#define E2_DRIVER_TYPE A4988
+#define E3_DRIVER_TYPE A4988
+#define E4_DRIVER_TYPE A4988
+
 // Enable this feature if all enabled endstop pins are interrupt-capable.
 // This will remove the need to poll the interrupt pins, saving many CPU cycles.
 //#define ENDSTOP_INTERRUPTS_FEATURE
--- a/Marlin/src/config/examples/Geeetech/Prusa
+++ b/Marlin/src/config/examples/Geeetech/Prusa
@ -837,15 +837,17 @@

 /**
 * Minimum delay after setting the stepper DIR (in ns)
- *    0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
- *   20 : Minimum for TMC2xxx drivers
- *  200 : Minimum for A4988 drivers
- *  500 : Minimum for LV8729 drivers (guess, no info in datasheet)
- *  650 : Minimum for DRV8825 drivers
- * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
- *15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *     0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
+ *    20 : Minimum for TMC2xxx drivers
+ *   200 : Minimum for A4988 drivers
+ *   500 : Minimum for LV8729 drivers (guess, no info in datasheet)
+ *   650 : Minimum for DRV8825 drivers
+ *  1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
+ * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_DIR_DELAY 0
+//#define MINIMUM_STEPPER_DIR_DELAY 650

 /**
 * Minimum stepper driver pulse width (in µs)
@ -855,8 +857,10 @@
 *   2 : Minimum for DRV8825 stepper drivers
 *   3 : Minimum for TB6600 stepper drivers
 *  30 : Minimum for TB6560 stepper drivers
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_PULSE 2
+//#define MINIMUM_STEPPER_PULSE 2

 /**
 * Maximum stepping rate (in Hz) the stepper driver allows
@ -867,8 +871,10 @@
 *  150000 : Maximum for TB6600 stepper driver
 *  130000 : Maximum for LV8729 stepper driver
 *   15000 : Maximum for TB6560 stepper driver
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MAXIMUM_STEPPER_RATE 250000
+//#define MAXIMUM_STEPPER_RATE 250000

 // @section temperature

@ -1036,23 +1042,12 @@
 // @section tmc

 /**
- * Enable this section if you have TMC26X motor drivers.
- * You will need to import the TMC26XStepper library into the Arduino IDE for this
- * (https://github.com/trinamic/TMC26XStepper.git)
+ * TMC26X Stepper Driver options
+ *
+ * The TMC26XStepper library is required for this stepper driver.
+ * https://github.com/trinamic/TMC26XStepper
 */
-//#define HAVE_TMC26X
-#if ENABLED(HAVE_TMC26X)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC26X
-  //#define X2_IS_TMC26X
-  //#define Y_IS_TMC26X
-  //#define Y2_IS_TMC26X
-  //#define Z_IS_TMC26X
-  //#define Z2_IS_TMC26X
-  //#define E0_IS_TMC26X
-  //#define E1_IS_TMC26X
-  //#define E2_IS_TMC26X
-  //#define E3_IS_TMC26X
-  //#define E4_IS_TMC26X
+#if HAS_DRIVER(TMC26X)

  #define X_MAX_CURRENT     1000 // in mA
  #define X_SENSE_RESISTOR    91 // in mOhms
@ -1098,62 +1093,29 @@
  #define E4_SENSE_RESISTOR   91
  #define E4_MICROSTEPS       16

-#endif
+#endif // TMC26X

 // @section tmc_smart

 /**
- * Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
- *
- * You'll also need the TMC2130Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2130Stepper).
- *
 * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
 * the hardware SPI interface on your board and define the required CS pins
 * in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
 * You may also use software SPI if you wish to use general purpose IO pins.
- */
-//#define HAVE_TMC2130
-#if ENABLED(HAVE_TMC2130)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2130
-  //#define X2_IS_TMC2130
-  //#define Y_IS_TMC2130
-  //#define Y2_IS_TMC2130
-  //#define Z_IS_TMC2130
-  //#define Z2_IS_TMC2130
-  //#define E0_IS_TMC2130
-  //#define E1_IS_TMC2130
-  //#define E2_IS_TMC2130
-  //#define E3_IS_TMC2130
-  //#define E4_IS_TMC2130
-#endif
-
-/**
- * Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
- * Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
+ *
+ * The TMC2130Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2130Stepper
+ *
+ * To use TMC2208 stepper UART-configurable stepper drivers
+ * connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
 * To use the reading capabilities, also connect #_SERIAL_RX_PIN
 * to PDN_UART without a resistor.
 * The drivers can also be used with hardware serial.
 *
- * You'll also need the TMC2208Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2208Stepper).
+ * The TMC2208Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2208Stepper
 */
-//#define HAVE_TMC2208
-#if ENABLED(HAVE_TMC2208)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2208
-  //#define X2_IS_TMC2208
-  //#define Y_IS_TMC2208
-  //#define Y2_IS_TMC2208
-  //#define Z_IS_TMC2208
-  //#define Z2_IS_TMC2208
-  //#define E0_IS_TMC2208
-  //#define E1_IS_TMC2208
-  //#define E2_IS_TMC2208
-  //#define E3_IS_TMC2208
-  //#define E4_IS_TMC2208
-#endif
-
-#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
+#if HAS_TRINAMIC

  #define R_SENSE           0.11  // R_sense resistor for SilentStepStick2130
  #define HOLD_MULTIPLIER    0.5  // Scales down the holding current from run current
@ -1308,25 +1270,12 @@
 // @section L6470

 /**
- * Enable this section if you have L6470 motor drivers.
- * You need to import the L6470 library into the Arduino IDE for this.
- * (https://github.com/ameyer/Arduino-L6470)
+ * L6470 Stepper Driver options
+ *
+ * The Arduino-L6470 library is required for this stepper driver.
+ * https://github.com/ameyer/Arduino-L6470
 */
-
-//#define HAVE_L6470DRIVER
-#if ENABLED(HAVE_L6470DRIVER)
-
-  //#define X_IS_L6470
-  //#define X2_IS_L6470
-  //#define Y_IS_L6470
-  //#define Y2_IS_L6470
-  //#define Z_IS_L6470
-  //#define Z2_IS_L6470
-  //#define E0_IS_L6470
-  //#define E1_IS_L6470
-  //#define E2_IS_L6470
-  //#define E3_IS_L6470
-  //#define E4_IS_L6470
+#if HAS_DRIVER(L6470)

  #define X_MICROSTEPS      16 // number of microsteps
  #define X_OVERCURRENT   2000 // maxc current in mA. If the current goes over this value, the driver will switch off
@ -1372,7 +1321,7 @@
  #define E4_OVERCURRENT  2000
  #define E4_STALLCURRENT 1500

-#endif
+#endif // L6470

 /**
 * TWI/I2C BUS
--- a/Marlin/src/config/examples/Infitary/i3-M508/Configuration_adv.h
+++ b/Marlin/src/config/examples/Infitary/i3-M508/Configuration_adv.h
@ -837,15 +837,17 @@

 /**
 * Minimum delay after setting the stepper DIR (in ns)
- *    0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
- *   20 : Minimum for TMC2xxx drivers
- *  200 : Minimum for A4988 drivers
- *  500 : Minimum for LV8729 drivers (guess, no info in datasheet)
- *  650 : Minimum for DRV8825 drivers
- * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
- *15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *     0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
+ *    20 : Minimum for TMC2xxx drivers
+ *   200 : Minimum for A4988 drivers
+ *   500 : Minimum for LV8729 drivers (guess, no info in datasheet)
+ *   650 : Minimum for DRV8825 drivers
+ *  1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
+ * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_DIR_DELAY 0
+//#define MINIMUM_STEPPER_DIR_DELAY 650

 /**
 * Minimum stepper driver pulse width (in µs)
@ -855,8 +857,10 @@
 *   2 : Minimum for DRV8825 stepper drivers
 *   3 : Minimum for TB6600 stepper drivers
 *  30 : Minimum for TB6560 stepper drivers
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_PULSE 2
+//#define MINIMUM_STEPPER_PULSE 2

 /**
 * Maximum stepping rate (in Hz) the stepper driver allows
@ -867,8 +871,10 @@
 *  150000 : Maximum for TB6600 stepper driver
 *  130000 : Maximum for LV8729 stepper driver
 *   15000 : Maximum for TB6560 stepper driver
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MAXIMUM_STEPPER_RATE 250000
+//#define MAXIMUM_STEPPER_RATE 250000

 // @section temperature

@ -1036,23 +1042,12 @@
 // @section tmc

 /**
- * Enable this section if you have TMC26X motor drivers.
- * You will need to import the TMC26XStepper library into the Arduino IDE for this
- * (https://github.com/trinamic/TMC26XStepper.git)
+ * TMC26X Stepper Driver options
+ *
+ * The TMC26XStepper library is required for this stepper driver.
+ * https://github.com/trinamic/TMC26XStepper
 */
-//#define HAVE_TMC26X
-#if ENABLED(HAVE_TMC26X)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC26X
-  //#define X2_IS_TMC26X
-  //#define Y_IS_TMC26X
-  //#define Y2_IS_TMC26X
-  //#define Z_IS_TMC26X
-  //#define Z2_IS_TMC26X
-  //#define E0_IS_TMC26X
-  //#define E1_IS_TMC26X
-  //#define E2_IS_TMC26X
-  //#define E3_IS_TMC26X
-  //#define E4_IS_TMC26X
+#if HAS_DRIVER(TMC26X)

  #define X_MAX_CURRENT     1000 // in mA
  #define X_SENSE_RESISTOR    91 // in mOhms
@ -1098,62 +1093,29 @@
  #define E4_SENSE_RESISTOR   91
  #define E4_MICROSTEPS       16

-#endif
+#endif // TMC26X

 // @section tmc_smart

 /**
- * Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
- *
- * You'll also need the TMC2130Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2130Stepper).
- *
 * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
 * the hardware SPI interface on your board and define the required CS pins
 * in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
 * You may also use software SPI if you wish to use general purpose IO pins.
- */
-//#define HAVE_TMC2130
-#if ENABLED(HAVE_TMC2130)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2130
-  //#define X2_IS_TMC2130
-  //#define Y_IS_TMC2130
-  //#define Y2_IS_TMC2130
-  //#define Z_IS_TMC2130
-  //#define Z2_IS_TMC2130
-  //#define E0_IS_TMC2130
-  //#define E1_IS_TMC2130
-  //#define E2_IS_TMC2130
-  //#define E3_IS_TMC2130
-  //#define E4_IS_TMC2130
-#endif
-
-/**
- * Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
- * Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
+ *
+ * The TMC2130Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2130Stepper
+ *
+ * To use TMC2208 stepper UART-configurable stepper drivers
+ * connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
 * To use the reading capabilities, also connect #_SERIAL_RX_PIN
 * to PDN_UART without a resistor.
 * The drivers can also be used with hardware serial.
 *
- * You'll also need the TMC2208Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2208Stepper).
+ * The TMC2208Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2208Stepper
 */
-//#define HAVE_TMC2208
-#if ENABLED(HAVE_TMC2208)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2208
-  //#define X2_IS_TMC2208
-  //#define Y_IS_TMC2208
-  //#define Y2_IS_TMC2208
-  //#define Z_IS_TMC2208
-  //#define Z2_IS_TMC2208
-  //#define E0_IS_TMC2208
-  //#define E1_IS_TMC2208
-  //#define E2_IS_TMC2208
-  //#define E3_IS_TMC2208
-  //#define E4_IS_TMC2208
-#endif
-
-#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
+#if HAS_TRINAMIC

  #define R_SENSE           0.11  // R_sense resistor for SilentStepStick2130
  #define HOLD_MULTIPLIER    0.5  // Scales down the holding current from run current
@ -1308,25 +1270,12 @@
 // @section L6470

 /**
- * Enable this section if you have L6470 motor drivers.
- * You need to import the L6470 library into the Arduino IDE for this.
- * (https://github.com/ameyer/Arduino-L6470)
+ * L6470 Stepper Driver options
+ *
+ * The Arduino-L6470 library is required for this stepper driver.
+ * https://github.com/ameyer/Arduino-L6470
 */
-
-//#define HAVE_L6470DRIVER
-#if ENABLED(HAVE_L6470DRIVER)
-
-  //#define X_IS_L6470
-  //#define X2_IS_L6470
-  //#define Y_IS_L6470
-  //#define Y2_IS_L6470
-  //#define Z_IS_L6470
-  //#define Z2_IS_L6470
-  //#define E0_IS_L6470
-  //#define E1_IS_L6470
-  //#define E2_IS_L6470
-  //#define E3_IS_L6470
-  //#define E4_IS_L6470
+#if HAS_DRIVER(L6470)

  #define X_MICROSTEPS      16 // number of microsteps
  #define X_OVERCURRENT   2000 // maxc current in mA. If the current goes over this value, the driver will switch off
@ -1372,7 +1321,7 @@
  #define E4_OVERCURRENT  2000
  #define E4_STALLCURRENT 1500

-#endif
+#endif // L6470

 /**
 * TWI/I2C BUS
--- a/Marlin/src/config/examples/JGAurora/A5/Configuration.h
+++ b/Marlin/src/config/examples/JGAurora/A5/Configuration.h
@ -563,6 +563,29 @@
 #define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
 #define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.

+/**
+ * Specify Stepper Driver types
+ * The options are used to determine driver pulse timings as well as more advanced functionality.
+ * Stepper timing options can be overridden in Configuration_adv.h
+ *
+ * Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
+ *          TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
+ *          TMC26X,  TMC26X_STANDALONE,  TMC2660, TMC2660_STANDALONE,
+ *          TMC5130, TMC5130_STANDALONE
+ * :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
+ */
+#define X_DRIVER_TYPE  A4988
+#define Y_DRIVER_TYPE  A4988
+#define Z_DRIVER_TYPE  A4988
+#define X2_DRIVER_TYPE A4988
+#define Y2_DRIVER_TYPE A4988
+#define Z2_DRIVER_TYPE A4988
+#define E0_DRIVER_TYPE A4988
+#define E1_DRIVER_TYPE A4988
+#define E2_DRIVER_TYPE A4988
+#define E3_DRIVER_TYPE A4988
+#define E4_DRIVER_TYPE A4988
+
 // Enable this feature if all enabled endstop pins are interrupt-capable.
 // This will remove the need to poll the interrupt pins, saving many CPU cycles.
 //#define ENDSTOP_INTERRUPTS_FEATURE
--- a/Marlin/src/config/examples/JGAurora/A5/Configuration_adv.h
+++ b/Marlin/src/config/examples/JGAurora/A5/Configuration_adv.h
@ -837,15 +837,17 @@

 /**
 * Minimum delay after setting the stepper DIR (in ns)
- *    0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
- *   20 : Minimum for TMC2xxx drivers
- *  200 : Minimum for A4988 drivers
- *  500 : Minimum for LV8729 drivers (guess, no info in datasheet)
- *  650 : Minimum for DRV8825 drivers
- * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
- *15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *     0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
+ *    20 : Minimum for TMC2xxx drivers
+ *   200 : Minimum for A4988 drivers
+ *   500 : Minimum for LV8729 drivers (guess, no info in datasheet)
+ *   650 : Minimum for DRV8825 drivers
+ *  1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
+ * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_DIR_DELAY 0
+//#define MINIMUM_STEPPER_DIR_DELAY 650

 /**
 * Minimum stepper driver pulse width (in µs)
@ -855,8 +857,10 @@
 *   2 : Minimum for DRV8825 stepper drivers
 *   3 : Minimum for TB6600 stepper drivers
 *  30 : Minimum for TB6560 stepper drivers
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_PULSE 2
+//#define MINIMUM_STEPPER_PULSE 2

 /**
 * Maximum stepping rate (in Hz) the stepper driver allows
@ -867,8 +871,10 @@
 *  150000 : Maximum for TB6600 stepper driver
 *  130000 : Maximum for LV8729 stepper driver
 *   15000 : Maximum for TB6560 stepper driver
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MAXIMUM_STEPPER_RATE 250000
+//#define MAXIMUM_STEPPER_RATE 250000

 // @section temperature

@ -1036,23 +1042,12 @@
 // @section tmc

 /**
- * Enable this section if you have TMC26X motor drivers.
- * You will need to import the TMC26XStepper library into the Arduino IDE for this
- * (https://github.com/trinamic/TMC26XStepper.git)
+ * TMC26X Stepper Driver options
+ *
+ * The TMC26XStepper library is required for this stepper driver.
+ * https://github.com/trinamic/TMC26XStepper
 */
-//#define HAVE_TMC26X
-#if ENABLED(HAVE_TMC26X)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC26X
-  //#define X2_IS_TMC26X
-  //#define Y_IS_TMC26X
-  //#define Y2_IS_TMC26X
-  //#define Z_IS_TMC26X
-  //#define Z2_IS_TMC26X
-  //#define E0_IS_TMC26X
-  //#define E1_IS_TMC26X
-  //#define E2_IS_TMC26X
-  //#define E3_IS_TMC26X
-  //#define E4_IS_TMC26X
+#if HAS_DRIVER(TMC26X)

  #define X_MAX_CURRENT     1000 // in mA
  #define X_SENSE_RESISTOR    91 // in mOhms
@ -1098,62 +1093,29 @@
  #define E4_SENSE_RESISTOR   91
  #define E4_MICROSTEPS       16

-#endif
+#endif // TMC26X

 // @section tmc_smart

 /**
- * Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
- *
- * You'll also need the TMC2130Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2130Stepper).
- *
 * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
 * the hardware SPI interface on your board and define the required CS pins
 * in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
 * You may also use software SPI if you wish to use general purpose IO pins.
- */
-//#define HAVE_TMC2130
-#if ENABLED(HAVE_TMC2130)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2130
-  //#define X2_IS_TMC2130
-  //#define Y_IS_TMC2130
-  //#define Y2_IS_TMC2130
-  //#define Z_IS_TMC2130
-  //#define Z2_IS_TMC2130
-  //#define E0_IS_TMC2130
-  //#define E1_IS_TMC2130
-  //#define E2_IS_TMC2130
-  //#define E3_IS_TMC2130
-  //#define E4_IS_TMC2130
-#endif
-
-/**
- * Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
- * Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
+ *
+ * The TMC2130Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2130Stepper
+ *
+ * To use TMC2208 stepper UART-configurable stepper drivers
+ * connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
 * To use the reading capabilities, also connect #_SERIAL_RX_PIN
 * to PDN_UART without a resistor.
 * The drivers can also be used with hardware serial.
 *
- * You'll also need the TMC2208Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2208Stepper).
+ * The TMC2208Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2208Stepper
 */
-//#define HAVE_TMC2208
-#if ENABLED(HAVE_TMC2208)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2208
-  //#define X2_IS_TMC2208
-  //#define Y_IS_TMC2208
-  //#define Y2_IS_TMC2208
-  //#define Z_IS_TMC2208
-  //#define Z2_IS_TMC2208
-  //#define E0_IS_TMC2208
-  //#define E1_IS_TMC2208
-  //#define E2_IS_TMC2208
-  //#define E3_IS_TMC2208
-  //#define E4_IS_TMC2208
-#endif
-
-#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
+#if HAS_TRINAMIC

  #define R_SENSE           0.11  // R_sense resistor for SilentStepStick2130
  #define HOLD_MULTIPLIER    0.5  // Scales down the holding current from run current
@ -1308,25 +1270,12 @@
 // @section L6470

 /**
- * Enable this section if you have L6470 motor drivers.
- * You need to import the L6470 library into the Arduino IDE for this.
- * (https://github.com/ameyer/Arduino-L6470)
+ * L6470 Stepper Driver options
+ *
+ * The Arduino-L6470 library is required for this stepper driver.
+ * https://github.com/ameyer/Arduino-L6470
 */
-
-//#define HAVE_L6470DRIVER
-#if ENABLED(HAVE_L6470DRIVER)
-
-  //#define X_IS_L6470
-  //#define X2_IS_L6470
-  //#define Y_IS_L6470
-  //#define Y2_IS_L6470
-  //#define Z_IS_L6470
-  //#define Z2_IS_L6470
-  //#define E0_IS_L6470
-  //#define E1_IS_L6470
-  //#define E2_IS_L6470
-  //#define E3_IS_L6470
-  //#define E4_IS_L6470
+#if HAS_DRIVER(L6470)

  #define X_MICROSTEPS      16 // number of microsteps
  #define X_OVERCURRENT   2000 // maxc current in mA. If the current goes over this value, the driver will switch off
@ -1372,7 +1321,7 @@
  #define E4_OVERCURRENT  2000
  #define E4_STALLCURRENT 1500

-#endif
+#endif // L6470

 /**
 * TWI/I2C BUS
--- a/Marlin/src/config/examples/MakerParts/Configuration_adv.h
+++ b/Marlin/src/config/examples/MakerParts/Configuration_adv.h
@ -837,15 +837,17 @@

 /**
 * Minimum delay after setting the stepper DIR (in ns)
- *    0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
- *   20 : Minimum for TMC2xxx drivers
- *  200 : Minimum for A4988 drivers
- *  500 : Minimum for LV8729 drivers (guess, no info in datasheet)
- *  650 : Minimum for DRV8825 drivers
- * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
- *15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *     0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
+ *    20 : Minimum for TMC2xxx drivers
+ *   200 : Minimum for A4988 drivers
+ *   500 : Minimum for LV8729 drivers (guess, no info in datasheet)
+ *   650 : Minimum for DRV8825 drivers
+ *  1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
+ * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_DIR_DELAY 0
+//#define MINIMUM_STEPPER_DIR_DELAY 650

 /**
 * Minimum stepper driver pulse width (in µs)
@ -855,8 +857,10 @@
 *   2 : Minimum for DRV8825 stepper drivers
 *   3 : Minimum for TB6600 stepper drivers
 *  30 : Minimum for TB6560 stepper drivers
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_PULSE 2
+//#define MINIMUM_STEPPER_PULSE 2

 /**
 * Maximum stepping rate (in Hz) the stepper driver allows
@ -867,8 +871,10 @@
 *  150000 : Maximum for TB6600 stepper driver
 *  130000 : Maximum for LV8729 stepper driver
 *   15000 : Maximum for TB6560 stepper driver
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MAXIMUM_STEPPER_RATE 250000
+//#define MAXIMUM_STEPPER_RATE 250000

 // @section temperature

@ -1036,23 +1042,12 @@
 // @section tmc

 /**
- * Enable this section if you have TMC26X motor drivers.
- * You will need to import the TMC26XStepper library into the Arduino IDE for this
- * (https://github.com/trinamic/TMC26XStepper.git)
+ * TMC26X Stepper Driver options
+ *
+ * The TMC26XStepper library is required for this stepper driver.
+ * https://github.com/trinamic/TMC26XStepper
 */
-//#define HAVE_TMC26X
-#if ENABLED(HAVE_TMC26X)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC26X
-  //#define X2_IS_TMC26X
-  //#define Y_IS_TMC26X
-  //#define Y2_IS_TMC26X
-  //#define Z_IS_TMC26X
-  //#define Z2_IS_TMC26X
-  //#define E0_IS_TMC26X
-  //#define E1_IS_TMC26X
-  //#define E2_IS_TMC26X
-  //#define E3_IS_TMC26X
-  //#define E4_IS_TMC26X
+#if HAS_DRIVER(TMC26X)

  #define X_MAX_CURRENT     1000 // in mA
  #define X_SENSE_RESISTOR    91 // in mOhms
@ -1098,62 +1093,29 @@
  #define E4_SENSE_RESISTOR   91
  #define E4_MICROSTEPS       16

-#endif
+#endif // TMC26X

 // @section tmc_smart

 /**
- * Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
- *
- * You'll also need the TMC2130Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2130Stepper).
- *
 * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
 * the hardware SPI interface on your board and define the required CS pins
 * in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
 * You may also use software SPI if you wish to use general purpose IO pins.
- */
-//#define HAVE_TMC2130
-#if ENABLED(HAVE_TMC2130)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2130
-  //#define X2_IS_TMC2130
-  //#define Y_IS_TMC2130
-  //#define Y2_IS_TMC2130
-  //#define Z_IS_TMC2130
-  //#define Z2_IS_TMC2130
-  //#define E0_IS_TMC2130
-  //#define E1_IS_TMC2130
-  //#define E2_IS_TMC2130
-  //#define E3_IS_TMC2130
-  //#define E4_IS_TMC2130
-#endif
-
-/**
- * Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
- * Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
+ *
+ * The TMC2130Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2130Stepper
+ *
+ * To use TMC2208 stepper UART-configurable stepper drivers
+ * connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
 * To use the reading capabilities, also connect #_SERIAL_RX_PIN
 * to PDN_UART without a resistor.
 * The drivers can also be used with hardware serial.
 *
- * You'll also need the TMC2208Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2208Stepper).
+ * The TMC2208Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2208Stepper
 */
-//#define HAVE_TMC2208
-#if ENABLED(HAVE_TMC2208)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2208
-  //#define X2_IS_TMC2208
-  //#define Y_IS_TMC2208
-  //#define Y2_IS_TMC2208
-  //#define Z_IS_TMC2208
-  //#define Z2_IS_TMC2208
-  //#define E0_IS_TMC2208
-  //#define E1_IS_TMC2208
-  //#define E2_IS_TMC2208
-  //#define E3_IS_TMC2208
-  //#define E4_IS_TMC2208
-#endif
-
-#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
+#if HAS_TRINAMIC

  #define R_SENSE           0.11  // R_sense resistor for SilentStepStick2130
  #define HOLD_MULTIPLIER    0.5  // Scales down the holding current from run current
@ -1308,25 +1270,12 @@
 // @section L6470

 /**
- * Enable this section if you have L6470 motor drivers.
- * You need to import the L6470 library into the Arduino IDE for this.
- * (https://github.com/ameyer/Arduino-L6470)
+ * L6470 Stepper Driver options
+ *
+ * The Arduino-L6470 library is required for this stepper driver.
+ * https://github.com/ameyer/Arduino-L6470
 */
-
-//#define HAVE_L6470DRIVER
-#if ENABLED(HAVE_L6470DRIVER)
-
-  //#define X_IS_L6470
-  //#define X2_IS_L6470
-  //#define Y_IS_L6470
-  //#define Y2_IS_L6470
-  //#define Z_IS_L6470
-  //#define Z2_IS_L6470
-  //#define E0_IS_L6470
-  //#define E1_IS_L6470
-  //#define E2_IS_L6470
-  //#define E3_IS_L6470
-  //#define E4_IS_L6470
+#if HAS_DRIVER(L6470)

  #define X_MICROSTEPS      16 // number of microsteps
  #define X_OVERCURRENT   2000 // maxc current in mA. If the current goes over this value, the driver will switch off
@ -1372,7 +1321,7 @@
  #define E4_OVERCURRENT  2000
  #define E4_STALLCURRENT 1500

-#endif
+#endif // L6470

 /**
 * TWI/I2C BUS
--- a/Marlin/src/config/examples/Malyan/M150/Configuration_adv.h
+++ b/Marlin/src/config/examples/Malyan/M150/Configuration_adv.h
@ -837,15 +837,17 @@

 /**
 * Minimum delay after setting the stepper DIR (in ns)
- *    0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
- *   20 : Minimum for TMC2xxx drivers
- *  200 : Minimum for A4988 drivers
- *  500 : Minimum for LV8729 drivers (guess, no info in datasheet)
- *  650 : Minimum for DRV8825 drivers
- * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
- *15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *     0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
+ *    20 : Minimum for TMC2xxx drivers
+ *   200 : Minimum for A4988 drivers
+ *   500 : Minimum for LV8729 drivers (guess, no info in datasheet)
+ *   650 : Minimum for DRV8825 drivers
+ *  1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
+ * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_DIR_DELAY 0
+//#define MINIMUM_STEPPER_DIR_DELAY 650

 /**
 * Minimum stepper driver pulse width (in µs)
@ -855,8 +857,10 @@
 *   2 : Minimum for DRV8825 stepper drivers
 *   3 : Minimum for TB6600 stepper drivers
 *  30 : Minimum for TB6560 stepper drivers
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_PULSE 2
+//#define MINIMUM_STEPPER_PULSE 2

 /**
 * Maximum stepping rate (in Hz) the stepper driver allows
@ -867,8 +871,10 @@
 *  150000 : Maximum for TB6600 stepper driver
 *  130000 : Maximum for LV8729 stepper driver
 *   15000 : Maximum for TB6560 stepper driver
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MAXIMUM_STEPPER_RATE 250000
+//#define MAXIMUM_STEPPER_RATE 250000

 // @section temperature

@ -1036,23 +1042,12 @@
 // @section tmc

 /**
- * Enable this section if you have TMC26X motor drivers.
- * You will need to import the TMC26XStepper library into the Arduino IDE for this
- * (https://github.com/trinamic/TMC26XStepper.git)
+ * TMC26X Stepper Driver options
+ *
+ * The TMC26XStepper library is required for this stepper driver.
+ * https://github.com/trinamic/TMC26XStepper
 */
-//#define HAVE_TMC26X
-#if ENABLED(HAVE_TMC26X)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC26X
-  //#define X2_IS_TMC26X
-  //#define Y_IS_TMC26X
-  //#define Y2_IS_TMC26X
-  //#define Z_IS_TMC26X
-  //#define Z2_IS_TMC26X
-  //#define E0_IS_TMC26X
-  //#define E1_IS_TMC26X
-  //#define E2_IS_TMC26X
-  //#define E3_IS_TMC26X
-  //#define E4_IS_TMC26X
+#if HAS_DRIVER(TMC26X)

  #define X_MAX_CURRENT     1000 // in mA
  #define X_SENSE_RESISTOR    91 // in mOhms
@ -1098,62 +1093,29 @@
  #define E4_SENSE_RESISTOR   91
  #define E4_MICROSTEPS       16

-#endif
+#endif // TMC26X

 // @section tmc_smart

 /**
- * Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
- *
- * You'll also need the TMC2130Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2130Stepper).
- *
 * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
 * the hardware SPI interface on your board and define the required CS pins
 * in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
 * You may also use software SPI if you wish to use general purpose IO pins.
- */
-//#define HAVE_TMC2130
-#if ENABLED(HAVE_TMC2130)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2130
-  //#define X2_IS_TMC2130
-  //#define Y_IS_TMC2130
-  //#define Y2_IS_TMC2130
-  //#define Z_IS_TMC2130
-  //#define Z2_IS_TMC2130
-  //#define E0_IS_TMC2130
-  //#define E1_IS_TMC2130
-  //#define E2_IS_TMC2130
-  //#define E3_IS_TMC2130
-  //#define E4_IS_TMC2130
-#endif
-
-/**
- * Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
- * Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
+ *
+ * The TMC2130Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2130Stepper
+ *
+ * To use TMC2208 stepper UART-configurable stepper drivers
+ * connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
 * To use the reading capabilities, also connect #_SERIAL_RX_PIN
 * to PDN_UART without a resistor.
 * The drivers can also be used with hardware serial.
 *
- * You'll also need the TMC2208Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2208Stepper).
+ * The TMC2208Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2208Stepper
 */
-//#define HAVE_TMC2208
-#if ENABLED(HAVE_TMC2208)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2208
-  //#define X2_IS_TMC2208
-  //#define Y_IS_TMC2208
-  //#define Y2_IS_TMC2208
-  //#define Z_IS_TMC2208
-  //#define Z2_IS_TMC2208
-  //#define E0_IS_TMC2208
-  //#define E1_IS_TMC2208
-  //#define E2_IS_TMC2208
-  //#define E3_IS_TMC2208
-  //#define E4_IS_TMC2208
-#endif
-
-#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
+#if HAS_TRINAMIC

  #define R_SENSE           0.11  // R_sense resistor for SilentStepStick2130
  #define HOLD_MULTIPLIER    0.5  // Scales down the holding current from run current
@ -1308,25 +1270,12 @@
 // @section L6470

 /**
- * Enable this section if you have L6470 motor drivers.
- * You need to import the L6470 library into the Arduino IDE for this.
- * (https://github.com/ameyer/Arduino-L6470)
+ * L6470 Stepper Driver options
+ *
+ * The Arduino-L6470 library is required for this stepper driver.
+ * https://github.com/ameyer/Arduino-L6470
 */
-
-//#define HAVE_L6470DRIVER
-#if ENABLED(HAVE_L6470DRIVER)
-
-  //#define X_IS_L6470
-  //#define X2_IS_L6470
-  //#define Y_IS_L6470
-  //#define Y2_IS_L6470
-  //#define Z_IS_L6470
-  //#define Z2_IS_L6470
-  //#define E0_IS_L6470
-  //#define E1_IS_L6470
-  //#define E2_IS_L6470
-  //#define E3_IS_L6470
-  //#define E4_IS_L6470
+#if HAS_DRIVER(L6470)

  #define X_MICROSTEPS      16 // number of microsteps
  #define X_OVERCURRENT   2000 // maxc current in mA. If the current goes over this value, the driver will switch off
@ -1372,7 +1321,7 @@
  #define E4_OVERCURRENT  2000
  #define E4_STALLCURRENT 1500

-#endif
+#endif // L6470

 /**
 * TWI/I2C BUS
--- a/Marlin/src/config/examples/Malyan/M200/Configuration.h
+++ b/Marlin/src/config/examples/Malyan/M200/Configuration.h
@ -550,6 +550,29 @@
 #define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
 #define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.

+/**
+ * Specify Stepper Driver types
+ * The options are used to determine driver pulse timings as well as more advanced functionality.
+ * Stepper timing options can be overridden in Configuration_adv.h
+ *
+ * Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
+ *          TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
+ *          TMC26X,  TMC26X_STANDALONE,  TMC2660, TMC2660_STANDALONE,
+ *          TMC5130, TMC5130_STANDALONE
+ * :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
+ */
+#define X_DRIVER_TYPE  A4988
+#define Y_DRIVER_TYPE  A4988
+#define Z_DRIVER_TYPE  A4988
+#define X2_DRIVER_TYPE A4988
+#define Y2_DRIVER_TYPE A4988
+#define Z2_DRIVER_TYPE A4988
+#define E0_DRIVER_TYPE A4988
+#define E1_DRIVER_TYPE A4988
+#define E2_DRIVER_TYPE A4988
+#define E3_DRIVER_TYPE A4988
+#define E4_DRIVER_TYPE A4988
+
 // Enable this feature if all enabled endstop pins are interrupt-capable.
 // This will remove the need to poll the interrupt pins, saving many CPU cycles.
 //#define ENDSTOP_INTERRUPTS_FEATURE
--- a/Marlin/src/config/examples/Malyan/M200/Configuration_adv.h
+++ b/Marlin/src/config/examples/Malyan/M200/Configuration_adv.h
@ -837,15 +837,17 @@

 /**
 * Minimum delay after setting the stepper DIR (in ns)
- *    0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
- *   20 : Minimum for TMC2xxx drivers
- *  200 : Minimum for A4988 drivers
- *  500 : Minimum for LV8729 drivers (guess, no info in datasheet)
- *  650 : Minimum for DRV8825 drivers
- * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
- *15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *     0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
+ *    20 : Minimum for TMC2xxx drivers
+ *   200 : Minimum for A4988 drivers
+ *   500 : Minimum for LV8729 drivers (guess, no info in datasheet)
+ *   650 : Minimum for DRV8825 drivers
+ *  1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
+ * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_DIR_DELAY 0
+//#define MINIMUM_STEPPER_DIR_DELAY 650

 /**
 * Minimum stepper driver pulse width (in µs)
@ -855,8 +857,10 @@
 *   2 : Minimum for DRV8825 stepper drivers
 *   3 : Minimum for TB6600 stepper drivers
 *  30 : Minimum for TB6560 stepper drivers
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_PULSE 2
+//#define MINIMUM_STEPPER_PULSE 2

 /**
 * Maximum stepping rate (in Hz) the stepper driver allows
@ -867,8 +871,10 @@
 *  150000 : Maximum for TB6600 stepper driver
 *  130000 : Maximum for LV8729 stepper driver
 *   15000 : Maximum for TB6560 stepper driver
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MAXIMUM_STEPPER_RATE 250000
+//#define MAXIMUM_STEPPER_RATE 250000

 // @section temperature

@ -1036,23 +1042,12 @@
 // @section tmc

 /**
- * Enable this section if you have TMC26X motor drivers.
- * You will need to import the TMC26XStepper library into the Arduino IDE for this
- * (https://github.com/trinamic/TMC26XStepper.git)
+ * TMC26X Stepper Driver options
+ *
+ * The TMC26XStepper library is required for this stepper driver.
+ * https://github.com/trinamic/TMC26XStepper
 */
-//#define HAVE_TMC26X
-#if ENABLED(HAVE_TMC26X)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC26X
-  //#define X2_IS_TMC26X
-  //#define Y_IS_TMC26X
-  //#define Y2_IS_TMC26X
-  //#define Z_IS_TMC26X
-  //#define Z2_IS_TMC26X
-  //#define E0_IS_TMC26X
-  //#define E1_IS_TMC26X
-  //#define E2_IS_TMC26X
-  //#define E3_IS_TMC26X
-  //#define E4_IS_TMC26X
+#if HAS_DRIVER(TMC26X)

  #define X_MAX_CURRENT     1000 // in mA
  #define X_SENSE_RESISTOR    91 // in mOhms
@ -1098,62 +1093,29 @@
  #define E4_SENSE_RESISTOR   91
  #define E4_MICROSTEPS       16

-#endif
+#endif // TMC26X

 // @section tmc_smart

 /**
- * Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
- *
- * You'll also need the TMC2130Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2130Stepper).
- *
 * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
 * the hardware SPI interface on your board and define the required CS pins
 * in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
 * You may also use software SPI if you wish to use general purpose IO pins.
- */
-//#define HAVE_TMC2130
-#if ENABLED(HAVE_TMC2130)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2130
-  //#define X2_IS_TMC2130
-  //#define Y_IS_TMC2130
-  //#define Y2_IS_TMC2130
-  //#define Z_IS_TMC2130
-  //#define Z2_IS_TMC2130
-  //#define E0_IS_TMC2130
-  //#define E1_IS_TMC2130
-  //#define E2_IS_TMC2130
-  //#define E3_IS_TMC2130
-  //#define E4_IS_TMC2130
-#endif
-
-/**
- * Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
- * Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
+ *
+ * The TMC2130Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2130Stepper
+ *
+ * To use TMC2208 stepper UART-configurable stepper drivers
+ * connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
 * To use the reading capabilities, also connect #_SERIAL_RX_PIN
 * to PDN_UART without a resistor.
 * The drivers can also be used with hardware serial.
 *
- * You'll also need the TMC2208Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2208Stepper).
+ * The TMC2208Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2208Stepper
 */
-//#define HAVE_TMC2208
-#if ENABLED(HAVE_TMC2208)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2208
-  //#define X2_IS_TMC2208
-  //#define Y_IS_TMC2208
-  //#define Y2_IS_TMC2208
-  //#define Z_IS_TMC2208
-  //#define Z2_IS_TMC2208
-  //#define E0_IS_TMC2208
-  //#define E1_IS_TMC2208
-  //#define E2_IS_TMC2208
-  //#define E3_IS_TMC2208
-  //#define E4_IS_TMC2208
-#endif
-
-#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
+#if HAS_TRINAMIC

  #define R_SENSE           0.11  // R_sense resistor for SilentStepStick2130
  #define HOLD_MULTIPLIER    0.5  // Scales down the holding current from run current
@ -1308,25 +1270,12 @@
 // @section L6470

 /**
- * Enable this section if you have L6470 motor drivers.
- * You need to import the L6470 library into the Arduino IDE for this.
- * (https://github.com/ameyer/Arduino-L6470)
+ * L6470 Stepper Driver options
+ *
+ * The Arduino-L6470 library is required for this stepper driver.
+ * https://github.com/ameyer/Arduino-L6470
 */
-
-//#define HAVE_L6470DRIVER
-#if ENABLED(HAVE_L6470DRIVER)
-
-  //#define X_IS_L6470
-  //#define X2_IS_L6470
-  //#define Y_IS_L6470
-  //#define Y2_IS_L6470
-  //#define Z_IS_L6470
-  //#define Z2_IS_L6470
-  //#define E0_IS_L6470
-  //#define E1_IS_L6470
-  //#define E2_IS_L6470
-  //#define E3_IS_L6470
-  //#define E4_IS_L6470
+#if HAS_DRIVER(L6470)

  #define X_MICROSTEPS      16 // number of microsteps
  #define X_OVERCURRENT   2000 // maxc current in mA. If the current goes over this value, the driver will switch off
@ -1372,7 +1321,7 @@
  #define E4_OVERCURRENT  2000
  #define E4_STALLCURRENT 1500

-#endif
+#endif // L6470

 /**
 * TWI/I2C BUS
--- a/Marlin/src/config/examples/Micromake/C1/basic/Configuration.h
+++ b/Marlin/src/config/examples/Micromake/C1/basic/Configuration.h
@ -551,6 +551,29 @@
 #define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
 #define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.

+/**
+ * Specify Stepper Driver types
+ * The options are used to determine driver pulse timings as well as more advanced functionality.
+ * Stepper timing options can be overridden in Configuration_adv.h
+ *
+ * Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
+ *          TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
+ *          TMC26X,  TMC26X_STANDALONE,  TMC2660, TMC2660_STANDALONE,
+ *          TMC5130, TMC5130_STANDALONE
+ * :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
+ */
+#define X_DRIVER_TYPE  A4988
+#define Y_DRIVER_TYPE  A4988
+#define Z_DRIVER_TYPE  A4988
+#define X2_DRIVER_TYPE A4988
+#define Y2_DRIVER_TYPE A4988
+#define Z2_DRIVER_TYPE A4988
+#define E0_DRIVER_TYPE A4988
+#define E1_DRIVER_TYPE A4988
+#define E2_DRIVER_TYPE A4988
+#define E3_DRIVER_TYPE A4988
+#define E4_DRIVER_TYPE A4988
+
 // Enable this feature if all enabled endstop pins are interrupt-capable.
 // This will remove the need to poll the interrupt pins, saving many CPU cycles.
 //#define ENDSTOP_INTERRUPTS_FEATURE
--- a/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration_adv.h
+++ b/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration_adv.h
@ -837,15 +837,17 @@

 /**
 * Minimum delay after setting the stepper DIR (in ns)
- *    0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
- *   20 : Minimum for TMC2xxx drivers
- *  200 : Minimum for A4988 drivers
- *  500 : Minimum for LV8729 drivers (guess, no info in datasheet)
- *  650 : Minimum for DRV8825 drivers
- * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
- *15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *     0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
+ *    20 : Minimum for TMC2xxx drivers
+ *   200 : Minimum for A4988 drivers
+ *   500 : Minimum for LV8729 drivers (guess, no info in datasheet)
+ *   650 : Minimum for DRV8825 drivers
+ *  1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
+ * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_DIR_DELAY 0
+//#define MINIMUM_STEPPER_DIR_DELAY 650

 /**
 * Minimum stepper driver pulse width (in µs)
@ -855,8 +857,10 @@
 *   2 : Minimum for DRV8825 stepper drivers
 *   3 : Minimum for TB6600 stepper drivers
 *  30 : Minimum for TB6560 stepper drivers
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_PULSE 2
+//#define MINIMUM_STEPPER_PULSE 2

 /**
 * Maximum stepping rate (in Hz) the stepper driver allows
@ -867,8 +871,10 @@
 *  150000 : Maximum for TB6600 stepper driver
 *  130000 : Maximum for LV8729 stepper driver
 *   15000 : Maximum for TB6560 stepper driver
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MAXIMUM_STEPPER_RATE 250000
+//#define MAXIMUM_STEPPER_RATE 250000

 // @section temperature

@ -1036,23 +1042,12 @@
 // @section tmc

 /**
- * Enable this section if you have TMC26X motor drivers.
- * You will need to import the TMC26XStepper library into the Arduino IDE for this
- * (https://github.com/trinamic/TMC26XStepper.git)
+ * TMC26X Stepper Driver options
+ *
+ * The TMC26XStepper library is required for this stepper driver.
+ * https://github.com/trinamic/TMC26XStepper
 */
-//#define HAVE_TMC26X
-#if ENABLED(HAVE_TMC26X)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC26X
-  //#define X2_IS_TMC26X
-  //#define Y_IS_TMC26X
-  //#define Y2_IS_TMC26X
-  //#define Z_IS_TMC26X
-  //#define Z2_IS_TMC26X
-  //#define E0_IS_TMC26X
-  //#define E1_IS_TMC26X
-  //#define E2_IS_TMC26X
-  //#define E3_IS_TMC26X
-  //#define E4_IS_TMC26X
+#if HAS_DRIVER(TMC26X)

  #define X_MAX_CURRENT     1000 // in mA
  #define X_SENSE_RESISTOR    91 // in mOhms
@ -1098,62 +1093,29 @@
  #define E4_SENSE_RESISTOR   91
  #define E4_MICROSTEPS       16

-#endif
+#endif // TMC26X

 // @section tmc_smart

 /**
- * Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
- *
- * You'll also need the TMC2130Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2130Stepper).
- *
 * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
 * the hardware SPI interface on your board and define the required CS pins
 * in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
 * You may also use software SPI if you wish to use general purpose IO pins.
- */
-//#define HAVE_TMC2130
-#if ENABLED(HAVE_TMC2130)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2130
-  //#define X2_IS_TMC2130
-  //#define Y_IS_TMC2130
-  //#define Y2_IS_TMC2130
-  //#define Z_IS_TMC2130
-  //#define Z2_IS_TMC2130
-  //#define E0_IS_TMC2130
-  //#define E1_IS_TMC2130
-  //#define E2_IS_TMC2130
-  //#define E3_IS_TMC2130
-  //#define E4_IS_TMC2130
-#endif
-
-/**
- * Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
- * Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
+ *
+ * The TMC2130Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2130Stepper
+ *
+ * To use TMC2208 stepper UART-configurable stepper drivers
+ * connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
 * To use the reading capabilities, also connect #_SERIAL_RX_PIN
 * to PDN_UART without a resistor.
 * The drivers can also be used with hardware serial.
 *
- * You'll also need the TMC2208Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2208Stepper).
+ * The TMC2208Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2208Stepper
 */
-//#define HAVE_TMC2208
-#if ENABLED(HAVE_TMC2208)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2208
-  //#define X2_IS_TMC2208
-  //#define Y_IS_TMC2208
-  //#define Y2_IS_TMC2208
-  //#define Z_IS_TMC2208
-  //#define Z2_IS_TMC2208
-  //#define E0_IS_TMC2208
-  //#define E1_IS_TMC2208
-  //#define E2_IS_TMC2208
-  //#define E3_IS_TMC2208
-  //#define E4_IS_TMC2208
-#endif
-
-#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
+#if HAS_TRINAMIC

  #define R_SENSE           0.11  // R_sense resistor for SilentStepStick2130
  #define HOLD_MULTIPLIER    0.5  // Scales down the holding current from run current
@ -1308,25 +1270,12 @@
 // @section L6470

 /**
- * Enable this section if you have L6470 motor drivers.
- * You need to import the L6470 library into the Arduino IDE for this.
- * (https://github.com/ameyer/Arduino-L6470)
+ * L6470 Stepper Driver options
+ *
+ * The Arduino-L6470 library is required for this stepper driver.
+ * https://github.com/ameyer/Arduino-L6470
 */
-
-//#define HAVE_L6470DRIVER
-#if ENABLED(HAVE_L6470DRIVER)
-
-  //#define X_IS_L6470
-  //#define X2_IS_L6470
-  //#define Y_IS_L6470
-  //#define Y2_IS_L6470
-  //#define Z_IS_L6470
-  //#define Z2_IS_L6470
-  //#define E0_IS_L6470
-  //#define E1_IS_L6470
-  //#define E2_IS_L6470
-  //#define E3_IS_L6470
-  //#define E4_IS_L6470
+#if HAS_DRIVER(L6470)

  #define X_MICROSTEPS      16 // number of microsteps
  #define X_OVERCURRENT   2000 // maxc current in mA. If the current goes over this value, the driver will switch off
@ -1372,7 +1321,7 @@
  #define E4_OVERCURRENT  2000
  #define E4_STALLCURRENT 1500

-#endif
+#endif // L6470

 /**
 * TWI/I2C BUS
--- a/Marlin/src/config/examples/Mks/Sbase/Configuration_adv.h
+++ b/Marlin/src/config/examples/Mks/Sbase/Configuration_adv.h
@ -845,15 +845,17 @@

 /**
 * Minimum delay after setting the stepper DIR (in ns)
- *    0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
- *   20 : Minimum for TMC2xxx drivers
- *  200 : Minimum for A4988 drivers
- *  500 : Minimum for LV8729 drivers (guess, no info in datasheet)
- *  650 : Minimum for DRV8825 drivers
- * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
- *15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *     0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
+ *    20 : Minimum for TMC2xxx drivers
+ *   200 : Minimum for A4988 drivers
+ *   500 : Minimum for LV8729 drivers (guess, no info in datasheet)
+ *   650 : Minimum for DRV8825 drivers
+ *  1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
+ * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_DIR_DELAY 0
+//#define MINIMUM_STEPPER_DIR_DELAY 650

 /**
 * Minimum stepper driver pulse width (in µs)
@ -863,8 +865,10 @@
 *   2 : Minimum for DRV8825 stepper drivers
 *   3 : Minimum for TB6600 stepper drivers
 *  30 : Minimum for TB6560 stepper drivers
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_PULSE 4
+//#define MINIMUM_STEPPER_PULSE 2

 /**
 * Maximum stepping rate (in Hz) the stepper driver allows
@ -875,8 +879,10 @@
 *  150000 : Maximum for TB6600 stepper driver
 *  130000 : Maximum for LV8729 stepper driver
 *   15000 : Maximum for TB6560 stepper driver
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MAXIMUM_STEPPER_RATE 250000
+//#define MAXIMUM_STEPPER_RATE 250000

 // @section temperature

@ -1044,23 +1050,12 @@
 // @section tmc

 /**
- * Enable this section if you have TMC26X motor drivers.
- * You will need to import the TMC26XStepper library into the Arduino IDE for this
- * (https://github.com/trinamic/TMC26XStepper.git)
+ * TMC26X Stepper Driver options
+ *
+ * The TMC26XStepper library is required for this stepper driver.
+ * https://github.com/trinamic/TMC26XStepper
 */
-//#define HAVE_TMC26X
-#if ENABLED(HAVE_TMC26X)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC26X
-  //#define X2_IS_TMC26X
-  //#define Y_IS_TMC26X
-  //#define Y2_IS_TMC26X
-  //#define Z_IS_TMC26X
-  //#define Z2_IS_TMC26X
-  //#define E0_IS_TMC26X
-  //#define E1_IS_TMC26X
-  //#define E2_IS_TMC26X
-  //#define E3_IS_TMC26X
-  //#define E4_IS_TMC26X
+#if HAS_DRIVER(TMC26X)

  #define X_MAX_CURRENT     1000 // in mA
  #define X_SENSE_RESISTOR    91 // in mOhms
@ -1106,62 +1101,29 @@
  #define E4_SENSE_RESISTOR   91
  #define E4_MICROSTEPS       16

-#endif
+#endif // TMC26X

 // @section tmc_smart

 /**
- * Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
- *
- * You'll also need the TMC2130Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2130Stepper).
- *
 * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
 * the hardware SPI interface on your board and define the required CS pins
 * in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
 * You may also use software SPI if you wish to use general purpose IO pins.
- */
-//#define HAVE_TMC2130
-#if ENABLED(HAVE_TMC2130)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2130
-  //#define X2_IS_TMC2130
-  //#define Y_IS_TMC2130
-  //#define Y2_IS_TMC2130
-  //#define Z_IS_TMC2130
-  //#define Z2_IS_TMC2130
-  //#define E0_IS_TMC2130
-  //#define E1_IS_TMC2130
-  //#define E2_IS_TMC2130
-  //#define E3_IS_TMC2130
-  //#define E4_IS_TMC2130
-#endif
-
-/**
- * Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
- * Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
+ *
+ * The TMC2130Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2130Stepper
+ *
+ * To use TMC2208 stepper UART-configurable stepper drivers
+ * connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
 * To use the reading capabilities, also connect #_SERIAL_RX_PIN
 * to PDN_UART without a resistor.
 * The drivers can also be used with hardware serial.
 *
- * You'll also need the TMC2208Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2208Stepper).
+ * The TMC2208Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2208Stepper
 */
-//#define HAVE_TMC2208
-#if ENABLED(HAVE_TMC2208)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2208
-  //#define X2_IS_TMC2208
-  //#define Y_IS_TMC2208
-  //#define Y2_IS_TMC2208
-  //#define Z_IS_TMC2208
-  //#define Z2_IS_TMC2208
-  //#define E0_IS_TMC2208
-  //#define E1_IS_TMC2208
-  //#define E2_IS_TMC2208
-  //#define E3_IS_TMC2208
-  //#define E4_IS_TMC2208
-#endif
-
-#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
+#if HAS_TRINAMIC

  #define R_SENSE           0.11  // R_sense resistor for SilentStepStick2130
  #define HOLD_MULTIPLIER    0.5  // Scales down the holding current from run current
@ -1316,25 +1278,12 @@
 // @section L6470

 /**
- * Enable this section if you have L6470 motor drivers.
- * You need to import the L6470 library into the Arduino IDE for this.
- * (https://github.com/ameyer/Arduino-L6470)
+ * L6470 Stepper Driver options
+ *
+ * The Arduino-L6470 library is required for this stepper driver.
+ * https://github.com/ameyer/Arduino-L6470
 */
-
-//#define HAVE_L6470DRIVER
-#if ENABLED(HAVE_L6470DRIVER)
-
-  //#define X_IS_L6470
-  //#define X2_IS_L6470
-  //#define Y_IS_L6470
-  //#define Y2_IS_L6470
-  //#define Z_IS_L6470
-  //#define Z2_IS_L6470
-  //#define E0_IS_L6470
-  //#define E1_IS_L6470
-  //#define E2_IS_L6470
-  //#define E3_IS_L6470
-  //#define E4_IS_L6470
+#if HAS_DRIVER(L6470)

  #define X_MICROSTEPS      16 // number of microsteps
  #define X_OVERCURRENT   2000 // maxc current in mA. If the current goes over this value, the driver will switch off
@ -1380,7 +1329,7 @@
  #define E4_OVERCURRENT  2000
  #define E4_STALLCURRENT 1500

-#endif
+#endif // L6470

 /**
 * TWI/I2C BUS
--- a/Marlin/src/config/examples/RepRapPro/Huxley/Configuration.h
+++ b/Marlin/src/config/examples/RepRapPro/Huxley/Configuration.h
@ -551,6 +551,29 @@
 #define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
 #define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.

+/**
+ * Specify Stepper Driver types
+ * The options are used to determine driver pulse timings as well as more advanced functionality.
+ * Stepper timing options can be overridden in Configuration_adv.h
+ *
+ * Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
+ *          TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
+ *          TMC26X,  TMC26X_STANDALONE,  TMC2660, TMC2660_STANDALONE,
+ *          TMC5130, TMC5130_STANDALONE
+ * :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
+ */
+#define X_DRIVER_TYPE  A4988
+#define Y_DRIVER_TYPE  A4988
+#define Z_DRIVER_TYPE  A4988
+#define X2_DRIVER_TYPE A4988
+#define Y2_DRIVER_TYPE A4988
+#define Z2_DRIVER_TYPE A4988
+#define E0_DRIVER_TYPE A4988
+#define E1_DRIVER_TYPE A4988
+#define E2_DRIVER_TYPE A4988
+#define E3_DRIVER_TYPE A4988
+#define E4_DRIVER_TYPE A4988
+
 // Enable this feature if all enabled endstop pins are interrupt-capable.
 // This will remove the need to poll the interrupt pins, saving many CPU cycles.
 //#define ENDSTOP_INTERRUPTS_FEATURE
--- a/Marlin/src/config/examples/RigidBot/Configuration_adv.h
+++ b/Marlin/src/config/examples/RigidBot/Configuration_adv.h
@ -837,15 +837,17 @@

 /**
 * Minimum delay after setting the stepper DIR (in ns)
- *    0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
- *   20 : Minimum for TMC2xxx drivers
- *  200 : Minimum for A4988 drivers
- *  500 : Minimum for LV8729 drivers (guess, no info in datasheet)
- *  650 : Minimum for DRV8825 drivers
- * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
- *15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *     0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
+ *    20 : Minimum for TMC2xxx drivers
+ *   200 : Minimum for A4988 drivers
+ *   500 : Minimum for LV8729 drivers (guess, no info in datasheet)
+ *   650 : Minimum for DRV8825 drivers
+ *  1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
+ * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_DIR_DELAY 0
+//#define MINIMUM_STEPPER_DIR_DELAY 650

 /**
 * Minimum stepper driver pulse width (in µs)
@ -855,8 +857,10 @@
 *   2 : Minimum for DRV8825 stepper drivers
 *   3 : Minimum for TB6600 stepper drivers
 *  30 : Minimum for TB6560 stepper drivers
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_PULSE 2
+//#define MINIMUM_STEPPER_PULSE 2

 /**
 * Maximum stepping rate (in Hz) the stepper driver allows
@ -867,8 +871,10 @@
 *  150000 : Maximum for TB6600 stepper driver
 *  130000 : Maximum for LV8729 stepper driver
 *   15000 : Maximum for TB6560 stepper driver
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MAXIMUM_STEPPER_RATE 250000
+//#define MAXIMUM_STEPPER_RATE 250000

 // @section temperature

@ -1036,23 +1042,12 @@
 // @section tmc

 /**
- * Enable this section if you have TMC26X motor drivers.
- * You will need to import the TMC26XStepper library into the Arduino IDE for this
- * (https://github.com/trinamic/TMC26XStepper.git)
+ * TMC26X Stepper Driver options
+ *
+ * The TMC26XStepper library is required for this stepper driver.
+ * https://github.com/trinamic/TMC26XStepper
 */
-//#define HAVE_TMC26X
-#if ENABLED(HAVE_TMC26X)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC26X
-  //#define X2_IS_TMC26X
-  //#define Y_IS_TMC26X
-  //#define Y2_IS_TMC26X
-  //#define Z_IS_TMC26X
-  //#define Z2_IS_TMC26X
-  //#define E0_IS_TMC26X
-  //#define E1_IS_TMC26X
-  //#define E2_IS_TMC26X
-  //#define E3_IS_TMC26X
-  //#define E4_IS_TMC26X
+#if HAS_DRIVER(TMC26X)

  #define X_MAX_CURRENT     1000 // in mA
  #define X_SENSE_RESISTOR    91 // in mOhms
@ -1098,62 +1093,29 @@
  #define E4_SENSE_RESISTOR   91
  #define E4_MICROSTEPS       16

-#endif
+#endif // TMC26X

 // @section tmc_smart

 /**
- * Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
- *
- * You'll also need the TMC2130Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2130Stepper).
- *
 * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
 * the hardware SPI interface on your board and define the required CS pins
 * in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
 * You may also use software SPI if you wish to use general purpose IO pins.
- */
-//#define HAVE_TMC2130
-#if ENABLED(HAVE_TMC2130)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2130
-  //#define X2_IS_TMC2130
-  //#define Y_IS_TMC2130
-  //#define Y2_IS_TMC2130
-  //#define Z_IS_TMC2130
-  //#define Z2_IS_TMC2130
-  //#define E0_IS_TMC2130
-  //#define E1_IS_TMC2130
-  //#define E2_IS_TMC2130
-  //#define E3_IS_TMC2130
-  //#define E4_IS_TMC2130
-#endif
-
-/**
- * Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
- * Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
+ *
+ * The TMC2130Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2130Stepper
+ *
+ * To use TMC2208 stepper UART-configurable stepper drivers
+ * connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
 * To use the reading capabilities, also connect #_SERIAL_RX_PIN
 * to PDN_UART without a resistor.
 * The drivers can also be used with hardware serial.
 *
- * You'll also need the TMC2208Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2208Stepper).
+ * The TMC2208Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2208Stepper
 */
-//#define HAVE_TMC2208
-#if ENABLED(HAVE_TMC2208)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2208
-  //#define X2_IS_TMC2208
-  //#define Y_IS_TMC2208
-  //#define Y2_IS_TMC2208
-  //#define Z_IS_TMC2208
-  //#define Z2_IS_TMC2208
-  //#define E0_IS_TMC2208
-  //#define E1_IS_TMC2208
-  //#define E2_IS_TMC2208
-  //#define E3_IS_TMC2208
-  //#define E4_IS_TMC2208
-#endif
-
-#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
+#if HAS_TRINAMIC

  #define R_SENSE           0.11  // R_sense resistor for SilentStepStick2130
  #define HOLD_MULTIPLIER    0.5  // Scales down the holding current from run current
@ -1308,25 +1270,12 @@
 // @section L6470

 /**
- * Enable this section if you have L6470 motor drivers.
- * You need to import the L6470 library into the Arduino IDE for this.
- * (https://github.com/ameyer/Arduino-L6470)
+ * L6470 Stepper Driver options
+ *
+ * The Arduino-L6470 library is required for this stepper driver.
+ * https://github.com/ameyer/Arduino-L6470
 */
-
-//#define HAVE_L6470DRIVER
-#if ENABLED(HAVE_L6470DRIVER)
-
-  //#define X_IS_L6470
-  //#define X2_IS_L6470
-  //#define Y_IS_L6470
-  //#define Y2_IS_L6470
-  //#define Z_IS_L6470
-  //#define Z2_IS_L6470
-  //#define E0_IS_L6470
-  //#define E1_IS_L6470
-  //#define E2_IS_L6470
-  //#define E3_IS_L6470
-  //#define E4_IS_L6470
+#if HAS_DRIVER(L6470)

  #define X_MICROSTEPS      16 // number of microsteps
  #define X_OVERCURRENT   2000 // maxc current in mA. If the current goes over this value, the driver will switch off
@ -1372,7 +1321,7 @@
  #define E4_OVERCURRENT  2000
  #define E4_STALLCURRENT 1500

-#endif
+#endif // L6470

 /**
 * TWI/I2C BUS
--- a/Marlin/src/config/examples/SCARA/Configuration_adv.h
+++ b/Marlin/src/config/examples/SCARA/Configuration_adv.h
@ -837,15 +837,17 @@

 /**
 * Minimum delay after setting the stepper DIR (in ns)
- *    0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
- *   20 : Minimum for TMC2xxx drivers
- *  200 : Minimum for A4988 drivers
- *  500 : Minimum for LV8729 drivers (guess, no info in datasheet)
- *  650 : Minimum for DRV8825 drivers
- * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
- *15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *     0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
+ *    20 : Minimum for TMC2xxx drivers
+ *   200 : Minimum for A4988 drivers
+ *   500 : Minimum for LV8729 drivers (guess, no info in datasheet)
+ *   650 : Minimum for DRV8825 drivers
+ *  1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
+ * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_DIR_DELAY 0
+//#define MINIMUM_STEPPER_DIR_DELAY 650

 /**
 * Minimum stepper driver pulse width (in µs)
@ -855,8 +857,10 @@
 *   2 : Minimum for DRV8825 stepper drivers
 *   3 : Minimum for TB6600 stepper drivers
 *  30 : Minimum for TB6560 stepper drivers
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_PULSE 2
+//#define MINIMUM_STEPPER_PULSE 2

 /**
 * Maximum stepping rate (in Hz) the stepper driver allows
@ -867,8 +871,10 @@
 *  150000 : Maximum for TB6600 stepper driver
 *  130000 : Maximum for LV8729 stepper driver
 *   15000 : Maximum for TB6560 stepper driver
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MAXIMUM_STEPPER_RATE 250000
+//#define MAXIMUM_STEPPER_RATE 250000

 // @section temperature

@ -1036,23 +1042,12 @@
 // @section tmc

 /**
- * Enable this section if you have TMC26X motor drivers.
- * You will need to import the TMC26XStepper library into the Arduino IDE for this
- * (https://github.com/trinamic/TMC26XStepper.git)
+ * TMC26X Stepper Driver options
+ *
+ * The TMC26XStepper library is required for this stepper driver.
+ * https://github.com/trinamic/TMC26XStepper
 */
-//#define HAVE_TMC26X
-#if ENABLED(HAVE_TMC26X)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC26X
-  //#define X2_IS_TMC26X
-  //#define Y_IS_TMC26X
-  //#define Y2_IS_TMC26X
-  //#define Z_IS_TMC26X
-  //#define Z2_IS_TMC26X
-  //#define E0_IS_TMC26X
-  //#define E1_IS_TMC26X
-  //#define E2_IS_TMC26X
-  //#define E3_IS_TMC26X
-  //#define E4_IS_TMC26X
+#if HAS_DRIVER(TMC26X)

  #define X_MAX_CURRENT     1000 // in mA
  #define X_SENSE_RESISTOR    91 // in mOhms
@ -1098,62 +1093,29 @@
  #define E4_SENSE_RESISTOR   91
  #define E4_MICROSTEPS       16

-#endif
+#endif // TMC26X

 // @section tmc_smart

 /**
- * Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
- *
- * You'll also need the TMC2130Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2130Stepper).
- *
 * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
 * the hardware SPI interface on your board and define the required CS pins
 * in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
 * You may also use software SPI if you wish to use general purpose IO pins.
- */
-//#define HAVE_TMC2130
-#if ENABLED(HAVE_TMC2130)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2130
-  //#define X2_IS_TMC2130
-  //#define Y_IS_TMC2130
-  //#define Y2_IS_TMC2130
-  //#define Z_IS_TMC2130
-  //#define Z2_IS_TMC2130
-  //#define E0_IS_TMC2130
-  //#define E1_IS_TMC2130
-  //#define E2_IS_TMC2130
-  //#define E3_IS_TMC2130
-  //#define E4_IS_TMC2130
-#endif
-
-/**
- * Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
- * Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
+ *
+ * The TMC2130Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2130Stepper
+ *
+ * To use TMC2208 stepper UART-configurable stepper drivers
+ * connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
 * To use the reading capabilities, also connect #_SERIAL_RX_PIN
 * to PDN_UART without a resistor.
 * The drivers can also be used with hardware serial.
 *
- * You'll also need the TMC2208Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2208Stepper).
+ * The TMC2208Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2208Stepper
 */
-//#define HAVE_TMC2208
-#if ENABLED(HAVE_TMC2208)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2208
-  //#define X2_IS_TMC2208
-  //#define Y_IS_TMC2208
-  //#define Y2_IS_TMC2208
-  //#define Z_IS_TMC2208
-  //#define Z2_IS_TMC2208
-  //#define E0_IS_TMC2208
-  //#define E1_IS_TMC2208
-  //#define E2_IS_TMC2208
-  //#define E3_IS_TMC2208
-  //#define E4_IS_TMC2208
-#endif
-
-#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
+#if HAS_TRINAMIC

  #define R_SENSE           0.11  // R_sense resistor for SilentStepStick2130
  #define HOLD_MULTIPLIER    0.5  // Scales down the holding current from run current
@ -1308,25 +1270,12 @@
 // @section L6470

 /**
- * Enable this section if you have L6470 motor drivers.
- * You need to import the L6470 library into the Arduino IDE for this.
- * (https://github.com/ameyer/Arduino-L6470)
+ * L6470 Stepper Driver options
+ *
+ * The Arduino-L6470 library is required for this stepper driver.
+ * https://github.com/ameyer/Arduino-L6470
 */
-
-//#define HAVE_L6470DRIVER
-#if ENABLED(HAVE_L6470DRIVER)
-
-  //#define X_IS_L6470
-  //#define X2_IS_L6470
-  //#define Y_IS_L6470
-  //#define Y2_IS_L6470
-  //#define Z_IS_L6470
-  //#define Z2_IS_L6470
-  //#define E0_IS_L6470
-  //#define E1_IS_L6470
-  //#define E2_IS_L6470
-  //#define E3_IS_L6470
-  //#define E4_IS_L6470
+#if HAS_DRIVER(L6470)

  #define X_MICROSTEPS      16 // number of microsteps
  #define X_OVERCURRENT   2000 // maxc current in mA. If the current goes over this value, the driver will switch off
@ -1372,7 +1321,7 @@
  #define E4_OVERCURRENT  2000
  #define E4_STALLCURRENT 1500

-#endif
+#endif // L6470

 /**
 * TWI/I2C BUS
--- a/Marlin/src/config/examples/STM32F10/Configuration.h
+++ b/Marlin/src/config/examples/STM32F10/Configuration.h
@ -553,6 +553,29 @@
 #define Z_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
 #define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.

+/**
+ * Specify Stepper Driver types
+ * The options are used to determine driver pulse timings as well as more advanced functionality.
+ * Stepper timing options can be overridden in Configuration_adv.h
+ *
+ * Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
+ *          TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
+ *          TMC26X,  TMC26X_STANDALONE,  TMC2660, TMC2660_STANDALONE,
+ *          TMC5130, TMC5130_STANDALONE
+ * :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
+ */
+#define X_DRIVER_TYPE  A4988
+#define Y_DRIVER_TYPE  A4988
+#define Z_DRIVER_TYPE  A4988
+#define X2_DRIVER_TYPE A4988
+#define Y2_DRIVER_TYPE A4988
+#define Z2_DRIVER_TYPE A4988
+#define E0_DRIVER_TYPE A4988
+#define E1_DRIVER_TYPE A4988
+#define E2_DRIVER_TYPE A4988
+#define E3_DRIVER_TYPE A4988
+#define E4_DRIVER_TYPE A4988
+
 // Enable this feature if all enabled endstop pins are interrupt-capable.
 // This will remove the need to poll the interrupt pins, saving many CPU cycles.
 //#define ENDSTOP_INTERRUPTS_FEATURE
--- a/Marlin/src/config/examples/STM32F4/Configuration.h
+++ b/Marlin/src/config/examples/STM32F4/Configuration.h
@ -551,6 +551,29 @@
 #define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
 #define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.

+/**
+ * Specify Stepper Driver types
+ * The options are used to determine driver pulse timings as well as more advanced functionality.
+ * Stepper timing options can be overridden in Configuration_adv.h
+ *
+ * Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
+ *          TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
+ *          TMC26X,  TMC26X_STANDALONE,  TMC2660, TMC2660_STANDALONE,
+ *          TMC5130, TMC5130_STANDALONE
+ * :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
+ */
+#define X_DRIVER_TYPE  A4988
+#define Y_DRIVER_TYPE  A4988
+#define Z_DRIVER_TYPE  A4988
+#define X2_DRIVER_TYPE A4988
+#define Y2_DRIVER_TYPE A4988
+#define Z2_DRIVER_TYPE A4988
+#define E0_DRIVER_TYPE A4988
+#define E1_DRIVER_TYPE A4988
+#define E2_DRIVER_TYPE A4988
+#define E3_DRIVER_TYPE A4988
+#define E4_DRIVER_TYPE A4988
+
 // Enable this feature if all enabled endstop pins are interrupt-capable.
 // This will remove the need to poll the interrupt pins, saving many CPU cycles.
 //#define ENDSTOP_INTERRUPTS_FEATURE
--- a/Marlin/src/config/examples/Sanguinololu/Configuration.h
+++ b/Marlin/src/config/examples/Sanguinololu/Configuration.h
@ -551,6 +551,29 @@
 #define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
 #define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.

+/**
+ * Specify Stepper Driver types
+ * The options are used to determine driver pulse timings as well as more advanced functionality.
+ * Stepper timing options can be overridden in Configuration_adv.h
+ *
+ * Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
+ *          TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
+ *          TMC26X,  TMC26X_STANDALONE,  TMC2660, TMC2660_STANDALONE,
+ *          TMC5130, TMC5130_STANDALONE
+ * :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
+ */
+#define X_DRIVER_TYPE  A4988
+#define Y_DRIVER_TYPE  A4988
+#define Z_DRIVER_TYPE  A4988
+#define X2_DRIVER_TYPE A4988
+#define Y2_DRIVER_TYPE A4988
+#define Z2_DRIVER_TYPE A4988
+#define E0_DRIVER_TYPE A4988
+#define E1_DRIVER_TYPE A4988
+#define E2_DRIVER_TYPE A4988
+#define E3_DRIVER_TYPE A4988
+#define E4_DRIVER_TYPE A4988
+
 // Enable this feature if all enabled endstop pins are interrupt-capable.
 // This will remove the need to poll the interrupt pins, saving many CPU cycles.
 //#define ENDSTOP_INTERRUPTS_FEATURE
--- a/Marlin/src/config/examples/Sanguinololu/Configuration_adv.h
+++ b/Marlin/src/config/examples/Sanguinololu/Configuration_adv.h
@ -837,15 +837,17 @@

 /**
 * Minimum delay after setting the stepper DIR (in ns)
- *    0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
- *   20 : Minimum for TMC2xxx drivers
- *  200 : Minimum for A4988 drivers
- *  500 : Minimum for LV8729 drivers (guess, no info in datasheet)
- *  650 : Minimum for DRV8825 drivers
- * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
- *15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *     0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
+ *    20 : Minimum for TMC2xxx drivers
+ *   200 : Minimum for A4988 drivers
+ *   500 : Minimum for LV8729 drivers (guess, no info in datasheet)
+ *   650 : Minimum for DRV8825 drivers
+ *  1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
+ * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_DIR_DELAY 0
+//#define MINIMUM_STEPPER_DIR_DELAY 650

 /**
 * Minimum stepper driver pulse width (in µs)
@ -855,8 +857,10 @@
 *   2 : Minimum for DRV8825 stepper drivers
 *   3 : Minimum for TB6600 stepper drivers
 *  30 : Minimum for TB6560 stepper drivers
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_PULSE 2
+//#define MINIMUM_STEPPER_PULSE 2

 /**
 * Maximum stepping rate (in Hz) the stepper driver allows
@ -867,8 +871,10 @@
 *  150000 : Maximum for TB6600 stepper driver
 *  130000 : Maximum for LV8729 stepper driver
 *   15000 : Maximum for TB6560 stepper driver
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MAXIMUM_STEPPER_RATE 250000
+//#define MAXIMUM_STEPPER_RATE 250000

 // @section temperature

@ -1036,23 +1042,12 @@
 // @section tmc

 /**
- * Enable this section if you have TMC26X motor drivers.
- * You will need to import the TMC26XStepper library into the Arduino IDE for this
- * (https://github.com/trinamic/TMC26XStepper.git)
+ * TMC26X Stepper Driver options
+ *
+ * The TMC26XStepper library is required for this stepper driver.
+ * https://github.com/trinamic/TMC26XStepper
 */
-//#define HAVE_TMC26X
-#if ENABLED(HAVE_TMC26X)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC26X
-  //#define X2_IS_TMC26X
-  //#define Y_IS_TMC26X
-  //#define Y2_IS_TMC26X
-  //#define Z_IS_TMC26X
-  //#define Z2_IS_TMC26X
-  //#define E0_IS_TMC26X
-  //#define E1_IS_TMC26X
-  //#define E2_IS_TMC26X
-  //#define E3_IS_TMC26X
-  //#define E4_IS_TMC26X
+#if HAS_DRIVER(TMC26X)

  #define X_MAX_CURRENT     1000 // in mA
  #define X_SENSE_RESISTOR    91 // in mOhms
@ -1098,62 +1093,29 @@
  #define E4_SENSE_RESISTOR   91
  #define E4_MICROSTEPS       16

-#endif
+#endif // TMC26X

 // @section tmc_smart

 /**
- * Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
- *
- * You'll also need the TMC2130Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2130Stepper).
- *
 * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
 * the hardware SPI interface on your board and define the required CS pins
 * in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
 * You may also use software SPI if you wish to use general purpose IO pins.
- */
-//#define HAVE_TMC2130
-#if ENABLED(HAVE_TMC2130)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2130
-  //#define X2_IS_TMC2130
-  //#define Y_IS_TMC2130
-  //#define Y2_IS_TMC2130
-  //#define Z_IS_TMC2130
-  //#define Z2_IS_TMC2130
-  //#define E0_IS_TMC2130
-  //#define E1_IS_TMC2130
-  //#define E2_IS_TMC2130
-  //#define E3_IS_TMC2130
-  //#define E4_IS_TMC2130
-#endif
-
-/**
- * Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
- * Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
+ *
+ * The TMC2130Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2130Stepper
+ *
+ * To use TMC2208 stepper UART-configurable stepper drivers
+ * connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
 * To use the reading capabilities, also connect #_SERIAL_RX_PIN
 * to PDN_UART without a resistor.
 * The drivers can also be used with hardware serial.
 *
- * You'll also need the TMC2208Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2208Stepper).
+ * The TMC2208Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2208Stepper
 */
-//#define HAVE_TMC2208
-#if ENABLED(HAVE_TMC2208)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2208
-  //#define X2_IS_TMC2208
-  //#define Y_IS_TMC2208
-  //#define Y2_IS_TMC2208
-  //#define Z_IS_TMC2208
-  //#define Z2_IS_TMC2208
-  //#define E0_IS_TMC2208
-  //#define E1_IS_TMC2208
-  //#define E2_IS_TMC2208
-  //#define E3_IS_TMC2208
-  //#define E4_IS_TMC2208
-#endif
-
-#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
+#if HAS_TRINAMIC

  #define R_SENSE           0.11  // R_sense resistor for SilentStepStick2130
  #define HOLD_MULTIPLIER    0.5  // Scales down the holding current from run current
@ -1308,25 +1270,12 @@
 // @section L6470

 /**
- * Enable this section if you have L6470 motor drivers.
- * You need to import the L6470 library into the Arduino IDE for this.
- * (https://github.com/ameyer/Arduino-L6470)
+ * L6470 Stepper Driver options
+ *
+ * The Arduino-L6470 library is required for this stepper driver.
+ * https://github.com/ameyer/Arduino-L6470
 */
-
-//#define HAVE_L6470DRIVER
-#if ENABLED(HAVE_L6470DRIVER)
-
-  //#define X_IS_L6470
-  //#define X2_IS_L6470
-  //#define Y_IS_L6470
-  //#define Y2_IS_L6470
-  //#define Z_IS_L6470
-  //#define Z2_IS_L6470
-  //#define E0_IS_L6470
-  //#define E1_IS_L6470
-  //#define E2_IS_L6470
-  //#define E3_IS_L6470
-  //#define E4_IS_L6470
+#if HAS_DRIVER(L6470)

  #define X_MICROSTEPS      16 // number of microsteps
  #define X_OVERCURRENT   2000 // maxc current in mA. If the current goes over this value, the driver will switch off
@ -1372,7 +1321,7 @@
  #define E4_OVERCURRENT  2000
  #define E4_STALLCURRENT 1500

-#endif
+#endif // L6470

 /**
 * TWI/I2C BUS
--- a/Marlin/src/config/examples/TheBorg/Configuration_adv.h
+++ b/Marlin/src/config/examples/TheBorg/Configuration_adv.h
@ -837,15 +837,17 @@

 /**
 * Minimum delay after setting the stepper DIR (in ns)
- *    0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
- *   20 : Minimum for TMC2xxx drivers
- *  200 : Minimum for A4988 drivers
- *  500 : Minimum for LV8729 drivers (guess, no info in datasheet)
- *  650 : Minimum for DRV8825 drivers
- * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
- *15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *     0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
+ *    20 : Minimum for TMC2xxx drivers
+ *   200 : Minimum for A4988 drivers
+ *   500 : Minimum for LV8729 drivers (guess, no info in datasheet)
+ *   650 : Minimum for DRV8825 drivers
+ *  1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
+ * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_DIR_DELAY 0
+//#define MINIMUM_STEPPER_DIR_DELAY 650

 /**
 * Minimum stepper driver pulse width (in µs)
@ -855,8 +857,10 @@
 *   2 : Minimum for DRV8825 stepper drivers
 *   3 : Minimum for TB6600 stepper drivers
 *  30 : Minimum for TB6560 stepper drivers
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_PULSE 2
+//#define MINIMUM_STEPPER_PULSE 2

 /**
 * Maximum stepping rate (in Hz) the stepper driver allows
@ -867,8 +871,10 @@
 *  150000 : Maximum for TB6600 stepper driver
 *  130000 : Maximum for LV8729 stepper driver
 *   15000 : Maximum for TB6560 stepper driver
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MAXIMUM_STEPPER_RATE 250000
+//#define MAXIMUM_STEPPER_RATE 250000

 // @section temperature

@ -1036,125 +1042,80 @@
 // @section tmc

 /**
- * Enable this section if you have TMC26X motor drivers.
- * You will need to import the TMC26XStepper library into the Arduino IDE for this
- * (https://github.com/trinamic/TMC26XStepper.git)
+ * TMC26X Stepper Driver options
+ *
+ * The TMC26XStepper library is required for this stepper driver.
+ * https://github.com/trinamic/TMC26XStepper
 */
-#define HAVE_TMC26X
-
-#if ENABLED(HAVE_TMC26X)  // Choose your axes here. This is mandatory!
-  #define X_IS_TMC26X
-  //#define X2_IS_TMC26X
-  #define Y_IS_TMC26X
-  //#define Y2_IS_TMC26X
-  #define Z_IS_TMC26X
-  #define Z2_IS_TMC26X
-  #define E0_IS_TMC26X
-  //#define E1_IS_TMC26X
-  //#define E2_IS_TMC26X
-  //#define E3_IS_TMC26X
-  //#define E4_IS_TMC26X
-
-  #define X_MAX_CURRENT     1200 // in mA
-  #define X_SENSE_RESISTOR    50 // in mOhms
-  #define X_MICROSTEPS        32 // number of microsteps
-
-  #define X2_MAX_CURRENT    1200
-  #define X2_SENSE_RESISTOR   50
-  #define X2_MICROSTEPS       32
-
-  #define Y_MAX_CURRENT     1200
-  #define Y_SENSE_RESISTOR    50
-  #define Y_MICROSTEPS        32
-
-  #define Y2_MAX_CURRENT    1200
-  #define Y2_SENSE_RESISTOR   50
-  #define Y2_MICROSTEPS       32
-
-  #define Z_MAX_CURRENT     1200
-  #define Z_SENSE_RESISTOR    50
-  #define Z_MICROSTEPS        32
-
-  #define Z2_MAX_CURRENT    1200
-  #define Z2_SENSE_RESISTOR   50
-  #define Z2_MICROSTEPS       32
-
-  #define E0_MAX_CURRENT    1200
-  #define E0_SENSE_RESISTOR   50
-  #define E0_MICROSTEPS       32
-
-  #define E1_MAX_CURRENT    1200
-  #define E1_SENSE_RESISTOR   50
-  #define E1_MICROSTEPS       32
-
-  #define E2_MAX_CURRENT    1200
-  #define E2_SENSE_RESISTOR   50
-  #define E2_MICROSTEPS       32
-
-  #define E3_MAX_CURRENT    1200
-  #define E3_SENSE_RESISTOR   50
-  #define E3_MICROSTEPS       32
-
-  #define E4_MAX_CURRENT    1200
-  #define E4_SENSE_RESISTOR   50
-  #define E4_MICROSTEPS       32
+#if HAS_DRIVER(TMC26X)

-#endif
+  #define X_MAX_CURRENT     1000 // in mA
+  #define X_SENSE_RESISTOR    91 // in mOhms
+  #define X_MICROSTEPS        16 // number of microsteps
+
+  #define X2_MAX_CURRENT    1000
+  #define X2_SENSE_RESISTOR   91
+  #define X2_MICROSTEPS       16
+
+  #define Y_MAX_CURRENT     1000
+  #define Y_SENSE_RESISTOR    91
+  #define Y_MICROSTEPS        16
+
+  #define Y2_MAX_CURRENT    1000
+  #define Y2_SENSE_RESISTOR   91
+  #define Y2_MICROSTEPS       16
+
+  #define Z_MAX_CURRENT     1000
+  #define Z_SENSE_RESISTOR    91
+  #define Z_MICROSTEPS        16
+
+  #define Z2_MAX_CURRENT    1000
+  #define Z2_SENSE_RESISTOR   91
+  #define Z2_MICROSTEPS       16
+
+  #define E0_MAX_CURRENT    1000
+  #define E0_SENSE_RESISTOR   91
+  #define E0_MICROSTEPS       16
+
+  #define E1_MAX_CURRENT    1000
+  #define E1_SENSE_RESISTOR   91
+  #define E1_MICROSTEPS       16
+
+  #define E2_MAX_CURRENT    1000
+  #define E2_SENSE_RESISTOR   91
+  #define E2_MICROSTEPS       16
+
+  #define E3_MAX_CURRENT    1000
+  #define E3_SENSE_RESISTOR   91
+  #define E3_MICROSTEPS       16
+
+  #define E4_MAX_CURRENT    1000
+  #define E4_SENSE_RESISTOR   91
+  #define E4_MICROSTEPS       16
+
+#endif // TMC26X

 // @section tmc_smart

 /**
- * Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
- *
- * You'll also need the TMC2130Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2130Stepper).
- *
 * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
 * the hardware SPI interface on your board and define the required CS pins
 * in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
 * You may also use software SPI if you wish to use general purpose IO pins.
- */
-//#define HAVE_TMC2130
-#if ENABLED(HAVE_TMC2130)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2130
-  //#define X2_IS_TMC2130
-  //#define Y_IS_TMC2130
-  //#define Y2_IS_TMC2130
-  //#define Z_IS_TMC2130
-  //#define Z2_IS_TMC2130
-  //#define E0_IS_TMC2130
-  //#define E1_IS_TMC2130
-  //#define E2_IS_TMC2130
-  //#define E3_IS_TMC2130
-  //#define E4_IS_TMC2130
-#endif
-
-/**
- * Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
- * Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
+ *
+ * The TMC2130Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2130Stepper
+ *
+ * To use TMC2208 stepper UART-configurable stepper drivers
+ * connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
 * To use the reading capabilities, also connect #_SERIAL_RX_PIN
 * to PDN_UART without a resistor.
 * The drivers can also be used with hardware serial.
 *
- * You'll also need the TMC2208Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2208Stepper).
+ * The TMC2208Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2208Stepper
 */
-//#define HAVE_TMC2208
-#if ENABLED(HAVE_TMC2208)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2208
-  //#define X2_IS_TMC2208
-  //#define Y_IS_TMC2208
-  //#define Y2_IS_TMC2208
-  //#define Z_IS_TMC2208
-  //#define Z2_IS_TMC2208
-  //#define E0_IS_TMC2208
-  //#define E1_IS_TMC2208
-  //#define E2_IS_TMC2208
-  //#define E3_IS_TMC2208
-  //#define E4_IS_TMC2208
-#endif
-
-#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
+#if HAS_TRINAMIC

  #define R_SENSE           0.11  // R_sense resistor for SilentStepStick2130
  #define HOLD_MULTIPLIER    0.5  // Scales down the holding current from run current
@ -1309,25 +1270,12 @@
 // @section L6470

 /**
- * Enable this section if you have L6470 motor drivers.
- * You need to import the L6470 library into the Arduino IDE for this.
- * (https://github.com/ameyer/Arduino-L6470)
+ * L6470 Stepper Driver options
+ *
+ * The Arduino-L6470 library is required for this stepper driver.
+ * https://github.com/ameyer/Arduino-L6470
 */
-
-//#define HAVE_L6470DRIVER
-#if ENABLED(HAVE_L6470DRIVER)
-
-  //#define X_IS_L6470
-  //#define X2_IS_L6470
-  //#define Y_IS_L6470
-  //#define Y2_IS_L6470
-  //#define Z_IS_L6470
-  //#define Z2_IS_L6470
-  //#define E0_IS_L6470
-  //#define E1_IS_L6470
-  //#define E2_IS_L6470
-  //#define E3_IS_L6470
-  //#define E4_IS_L6470
+#if HAS_DRIVER(L6470)

  #define X_MICROSTEPS      16 // number of microsteps
  #define X_OVERCURRENT   2000 // maxc current in mA. If the current goes over this value, the driver will switch off
@ -1373,7 +1321,7 @@
  #define E4_OVERCURRENT  2000
  #define E4_STALLCURRENT 1500

-#endif
+#endif // L6470

 /**
 * TWI/I2C BUS
--- a/Marlin/src/config/examples/TinyBoy2/Configuration.h
+++ b/Marlin/src/config/examples/TinyBoy2/Configuration.h
@ -602,9 +602,32 @@
 #define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
 #define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.

+/**
+ * Specify Stepper Driver types
+ * The options are used to determine driver pulse timings as well as more advanced functionality.
+ * Stepper timing options can be overridden in Configuration_adv.h
+ *
+ * Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
+ *          TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
+ *          TMC26X,  TMC26X_STANDALONE,  TMC2660, TMC2660_STANDALONE,
+ *          TMC5130, TMC5130_STANDALONE
+ * :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
+ */
+#define X_DRIVER_TYPE  A4988
+#define Y_DRIVER_TYPE  A4988
+#define Z_DRIVER_TYPE  A4988
+#define X2_DRIVER_TYPE A4988
+#define Y2_DRIVER_TYPE A4988
+#define Z2_DRIVER_TYPE A4988
+#define E0_DRIVER_TYPE A4988
+#define E1_DRIVER_TYPE A4988
+#define E2_DRIVER_TYPE A4988
+#define E3_DRIVER_TYPE A4988
+#define E4_DRIVER_TYPE A4988
+
 // Enable this feature if all enabled endstop pins are interrupt-capable.
 // This will remove the need to poll the interrupt pins, saving many CPU cycles.
-#define ENDSTOP_INTERRUPTS_FEATURE
+//#define ENDSTOP_INTERRUPTS_FEATURE

 /**
 * Endstop Noise Filter
--- a/Marlin/src/config/examples/TinyBoy2/Configuration_adv.h
+++ b/Marlin/src/config/examples/TinyBoy2/Configuration_adv.h
@ -837,15 +837,17 @@

 /**
 * Minimum delay after setting the stepper DIR (in ns)
- *    0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
- *   20 : Minimum for TMC2xxx drivers
- *  200 : Minimum for A4988 drivers
- *  500 : Minimum for LV8729 drivers (guess, no info in datasheet)
- *  650 : Minimum for DRV8825 drivers
- * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
- *15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *     0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
+ *    20 : Minimum for TMC2xxx drivers
+ *   200 : Minimum for A4988 drivers
+ *   500 : Minimum for LV8729 drivers (guess, no info in datasheet)
+ *   650 : Minimum for DRV8825 drivers
+ *  1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
+ * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_DIR_DELAY 0
+//#define MINIMUM_STEPPER_DIR_DELAY 650

 /**
 * Minimum stepper driver pulse width (in µs)
@ -855,8 +857,10 @@
 *   2 : Minimum for DRV8825 stepper drivers
 *   3 : Minimum for TB6600 stepper drivers
 *  30 : Minimum for TB6560 stepper drivers
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_PULSE 2
+//#define MINIMUM_STEPPER_PULSE 2

 /**
 * Maximum stepping rate (in Hz) the stepper driver allows
@ -867,8 +871,10 @@
 *  150000 : Maximum for TB6600 stepper driver
 *  130000 : Maximum for LV8729 stepper driver
 *   15000 : Maximum for TB6560 stepper driver
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MAXIMUM_STEPPER_RATE 250000
+//#define MAXIMUM_STEPPER_RATE 250000

 // @section temperature

@ -1036,23 +1042,12 @@
 // @section tmc

 /**
- * Enable this section if you have TMC26X motor drivers.
- * You will need to import the TMC26XStepper library into the Arduino IDE for this
- * (https://github.com/trinamic/TMC26XStepper.git)
+ * TMC26X Stepper Driver options
+ *
+ * The TMC26XStepper library is required for this stepper driver.
+ * https://github.com/trinamic/TMC26XStepper
 */
-//#define HAVE_TMC26X
-#if ENABLED(HAVE_TMC26X)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC26X
-  //#define X2_IS_TMC26X
-  //#define Y_IS_TMC26X
-  //#define Y2_IS_TMC26X
-  //#define Z_IS_TMC26X
-  //#define Z2_IS_TMC26X
-  //#define E0_IS_TMC26X
-  //#define E1_IS_TMC26X
-  //#define E2_IS_TMC26X
-  //#define E3_IS_TMC26X
-  //#define E4_IS_TMC26X
+#if HAS_DRIVER(TMC26X)

  #define X_MAX_CURRENT     1000 // in mA
  #define X_SENSE_RESISTOR    91 // in mOhms
@ -1098,62 +1093,29 @@
  #define E4_SENSE_RESISTOR   91
  #define E4_MICROSTEPS       16

-#endif
+#endif // TMC26X

 // @section tmc_smart

 /**
- * Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
- *
- * You'll also need the TMC2130Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2130Stepper).
- *
 * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
 * the hardware SPI interface on your board and define the required CS pins
 * in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
 * You may also use software SPI if you wish to use general purpose IO pins.
- */
-//#define HAVE_TMC2130
-#if ENABLED(HAVE_TMC2130)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2130
-  //#define X2_IS_TMC2130
-  //#define Y_IS_TMC2130
-  //#define Y2_IS_TMC2130
-  //#define Z_IS_TMC2130
-  //#define Z2_IS_TMC2130
-  //#define E0_IS_TMC2130
-  //#define E1_IS_TMC2130
-  //#define E2_IS_TMC2130
-  //#define E3_IS_TMC2130
-  //#define E4_IS_TMC2130
-#endif
-
-/**
- * Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
- * Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
+ *
+ * The TMC2130Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2130Stepper
+ *
+ * To use TMC2208 stepper UART-configurable stepper drivers
+ * connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
 * To use the reading capabilities, also connect #_SERIAL_RX_PIN
 * to PDN_UART without a resistor.
 * The drivers can also be used with hardware serial.
 *
- * You'll also need the TMC2208Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2208Stepper).
+ * The TMC2208Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2208Stepper
 */
-//#define HAVE_TMC2208
-#if ENABLED(HAVE_TMC2208)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2208
-  //#define X2_IS_TMC2208
-  //#define Y_IS_TMC2208
-  //#define Y2_IS_TMC2208
-  //#define Z_IS_TMC2208
-  //#define Z2_IS_TMC2208
-  //#define E0_IS_TMC2208
-  //#define E1_IS_TMC2208
-  //#define E2_IS_TMC2208
-  //#define E3_IS_TMC2208
-  //#define E4_IS_TMC2208
-#endif
-
-#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
+#if HAS_TRINAMIC

  #define R_SENSE           0.11  // R_sense resistor for SilentStepStick2130
  #define HOLD_MULTIPLIER    0.5  // Scales down the holding current from run current
@ -1308,25 +1270,12 @@
 // @section L6470

 /**
- * Enable this section if you have L6470 motor drivers.
- * You need to import the L6470 library into the Arduino IDE for this.
- * (https://github.com/ameyer/Arduino-L6470)
+ * L6470 Stepper Driver options
+ *
+ * The Arduino-L6470 library is required for this stepper driver.
+ * https://github.com/ameyer/Arduino-L6470
 */
-
-//#define HAVE_L6470DRIVER
-#if ENABLED(HAVE_L6470DRIVER)
-
-  //#define X_IS_L6470
-  //#define X2_IS_L6470
-  //#define Y_IS_L6470
-  //#define Y2_IS_L6470
-  //#define Z_IS_L6470
-  //#define Z2_IS_L6470
-  //#define E0_IS_L6470
-  //#define E1_IS_L6470
-  //#define E2_IS_L6470
-  //#define E3_IS_L6470
-  //#define E4_IS_L6470
+#if HAS_DRIVER(L6470)

  #define X_MICROSTEPS      16 // number of microsteps
  #define X_OVERCURRENT   2000 // maxc current in mA. If the current goes over this value, the driver will switch off
@ -1372,7 +1321,7 @@
  #define E4_OVERCURRENT  2000
  #define E4_STALLCURRENT 1500

-#endif
+#endif // L6470

 /**
 * TWI/I2C BUS
--- a/Marlin/src/config/examples/Tronxy/X1/Configuration.h
+++ b/Marlin/src/config/examples/Tronxy/X1/Configuration.h
@ -551,6 +551,29 @@
 #define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
 #define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.

+/**
+ * Specify Stepper Driver types
+ * The options are used to determine driver pulse timings as well as more advanced functionality.
+ * Stepper timing options can be overridden in Configuration_adv.h
+ *
+ * Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
+ *          TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
+ *          TMC26X,  TMC26X_STANDALONE,  TMC2660, TMC2660_STANDALONE,
+ *          TMC5130, TMC5130_STANDALONE
+ * :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
+ */
+#define X_DRIVER_TYPE  A4988
+#define Y_DRIVER_TYPE  A4988
+#define Z_DRIVER_TYPE  A4988
+#define X2_DRIVER_TYPE A4988
+#define Y2_DRIVER_TYPE A4988
+#define Z2_DRIVER_TYPE A4988
+#define E0_DRIVER_TYPE A4988
+#define E1_DRIVER_TYPE A4988
+#define E2_DRIVER_TYPE A4988
+#define E3_DRIVER_TYPE A4988
+#define E4_DRIVER_TYPE A4988
+
 // Enable this feature if all enabled endstop pins are interrupt-capable.
 // This will remove the need to poll the interrupt pins, saving many CPU cycles.
 //#define ENDSTOP_INTERRUPTS_FEATURE
--- a/Marlin/src/config/examples/Tronxy/X3A/Configuration_adv.h
+++ b/Marlin/src/config/examples/Tronxy/X3A/Configuration_adv.h
@ -837,15 +837,17 @@

 /**
 * Minimum delay after setting the stepper DIR (in ns)
- *    0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
- *   20 : Minimum for TMC2xxx drivers
- *  200 : Minimum for A4988 drivers
- *  500 : Minimum for LV8729 drivers (guess, no info in datasheet)
- *  650 : Minimum for DRV8825 drivers
- * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
- *15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *     0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
+ *    20 : Minimum for TMC2xxx drivers
+ *   200 : Minimum for A4988 drivers
+ *   500 : Minimum for LV8729 drivers (guess, no info in datasheet)
+ *   650 : Minimum for DRV8825 drivers
+ *  1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
+ * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_DIR_DELAY 0
+//#define MINIMUM_STEPPER_DIR_DELAY 650

 /**
 * Minimum stepper driver pulse width (in µs)
@ -855,8 +857,10 @@
 *   2 : Minimum for DRV8825 stepper drivers
 *   3 : Minimum for TB6600 stepper drivers
 *  30 : Minimum for TB6560 stepper drivers
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_PULSE 2
+//#define MINIMUM_STEPPER_PULSE 2

 /**
 * Maximum stepping rate (in Hz) the stepper driver allows
@ -867,8 +871,10 @@
 *  150000 : Maximum for TB6600 stepper driver
 *  130000 : Maximum for LV8729 stepper driver
 *   15000 : Maximum for TB6560 stepper driver
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MAXIMUM_STEPPER_RATE 250000
+//#define MAXIMUM_STEPPER_RATE 250000

 // @section temperature

@ -1036,23 +1042,12 @@
 // @section tmc

 /**
- * Enable this section if you have TMC26X motor drivers.
- * You will need to import the TMC26XStepper library into the Arduino IDE for this
- * (https://github.com/trinamic/TMC26XStepper.git)
+ * TMC26X Stepper Driver options
+ *
+ * The TMC26XStepper library is required for this stepper driver.
+ * https://github.com/trinamic/TMC26XStepper
 */
-//#define HAVE_TMC26X
-#if ENABLED(HAVE_TMC26X)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC26X
-  //#define X2_IS_TMC26X
-  //#define Y_IS_TMC26X
-  //#define Y2_IS_TMC26X
-  //#define Z_IS_TMC26X
-  //#define Z2_IS_TMC26X
-  //#define E0_IS_TMC26X
-  //#define E1_IS_TMC26X
-  //#define E2_IS_TMC26X
-  //#define E3_IS_TMC26X
-  //#define E4_IS_TMC26X
+#if HAS_DRIVER(TMC26X)

  #define X_MAX_CURRENT     1000 // in mA
  #define X_SENSE_RESISTOR    91 // in mOhms
@ -1098,62 +1093,29 @@
  #define E4_SENSE_RESISTOR   91
  #define E4_MICROSTEPS       16

-#endif
+#endif // TMC26X

 // @section tmc_smart

 /**
- * Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
- *
- * You'll also need the TMC2130Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2130Stepper).
- *
 * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
 * the hardware SPI interface on your board and define the required CS pins
 * in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
 * You may also use software SPI if you wish to use general purpose IO pins.
- */
-//#define HAVE_TMC2130
-#if ENABLED(HAVE_TMC2130)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2130
-  //#define X2_IS_TMC2130
-  //#define Y_IS_TMC2130
-  //#define Y2_IS_TMC2130
-  //#define Z_IS_TMC2130
-  //#define Z2_IS_TMC2130
-  //#define E0_IS_TMC2130
-  //#define E1_IS_TMC2130
-  //#define E2_IS_TMC2130
-  //#define E3_IS_TMC2130
-  //#define E4_IS_TMC2130
-#endif
-
-/**
- * Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
- * Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
+ *
+ * The TMC2130Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2130Stepper
+ *
+ * To use TMC2208 stepper UART-configurable stepper drivers
+ * connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
 * To use the reading capabilities, also connect #_SERIAL_RX_PIN
 * to PDN_UART without a resistor.
 * The drivers can also be used with hardware serial.
 *
- * You'll also need the TMC2208Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2208Stepper).
+ * The TMC2208Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2208Stepper
 */
-//#define HAVE_TMC2208
-#if ENABLED(HAVE_TMC2208)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2208
-  //#define X2_IS_TMC2208
-  //#define Y_IS_TMC2208
-  //#define Y2_IS_TMC2208
-  //#define Z_IS_TMC2208
-  //#define Z2_IS_TMC2208
-  //#define E0_IS_TMC2208
-  //#define E1_IS_TMC2208
-  //#define E2_IS_TMC2208
-  //#define E3_IS_TMC2208
-  //#define E4_IS_TMC2208
-#endif
-
-#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
+#if HAS_TRINAMIC

  #define R_SENSE           0.11  // R_sense resistor for SilentStepStick2130
  #define HOLD_MULTIPLIER    0.5  // Scales down the holding current from run current
@ -1308,25 +1270,12 @@
 // @section L6470

 /**
- * Enable this section if you have L6470 motor drivers.
- * You need to import the L6470 library into the Arduino IDE for this.
- * (https://github.com/ameyer/Arduino-L6470)
+ * L6470 Stepper Driver options
+ *
+ * The Arduino-L6470 library is required for this stepper driver.
+ * https://github.com/ameyer/Arduino-L6470
 */
-
-//#define HAVE_L6470DRIVER
-#if ENABLED(HAVE_L6470DRIVER)
-
-  //#define X_IS_L6470
-  //#define X2_IS_L6470
-  //#define Y_IS_L6470
-  //#define Y2_IS_L6470
-  //#define Z_IS_L6470
-  //#define Z2_IS_L6470
-  //#define E0_IS_L6470
-  //#define E1_IS_L6470
-  //#define E2_IS_L6470
-  //#define E3_IS_L6470
-  //#define E4_IS_L6470
+#if HAS_DRIVER(L6470)

  #define X_MICROSTEPS      16 // number of microsteps
  #define X_OVERCURRENT   2000 // maxc current in mA. If the current goes over this value, the driver will switch off
@ -1372,7 +1321,7 @@
  #define E4_OVERCURRENT  2000
  #define E4_STALLCURRENT 1500

-#endif
+#endif // L6470

 /**
 * TWI/I2C BUS
--- a/Marlin/src/config/examples/Tronxy/XY100/Configuration.h
+++ b/Marlin/src/config/examples/Tronxy/XY100/Configuration.h
@ -562,6 +562,29 @@
 #define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
 #define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.

+/**
+ * Specify Stepper Driver types
+ * The options are used to determine driver pulse timings as well as more advanced functionality.
+ * Stepper timing options can be overridden in Configuration_adv.h
+ *
+ * Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
+ *          TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
+ *          TMC26X,  TMC26X_STANDALONE,  TMC2660, TMC2660_STANDALONE,
+ *          TMC5130, TMC5130_STANDALONE
+ * :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
+ */
+#define X_DRIVER_TYPE  A4988
+#define Y_DRIVER_TYPE  A4988
+#define Z_DRIVER_TYPE  A4988
+#define X2_DRIVER_TYPE A4988
+#define Y2_DRIVER_TYPE A4988
+#define Z2_DRIVER_TYPE A4988
+#define E0_DRIVER_TYPE A4988
+#define E1_DRIVER_TYPE A4988
+#define E2_DRIVER_TYPE A4988
+#define E3_DRIVER_TYPE A4988
+#define E4_DRIVER_TYPE A4988
+
 // Enable this feature if all enabled endstop pins are interrupt-capable.
 // This will remove the need to poll the interrupt pins, saving many CPU cycles.
 //#define ENDSTOP_INTERRUPTS_FEATURE
--- a/Marlin/src/config/examples/UltiMachine/Archim2/Configuration.h
+++ b/Marlin/src/config/examples/UltiMachine/Archim2/Configuration.h
@ -551,6 +551,29 @@
 #define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
 #define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.

+/**
+ * Specify Stepper Driver types
+ * The options are used to determine driver pulse timings as well as more advanced functionality.
+ * Stepper timing options can be overridden in Configuration_adv.h
+ *
+ * Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
+ *          TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
+ *          TMC26X,  TMC26X_STANDALONE,  TMC2660, TMC2660_STANDALONE,
+ *          TMC5130, TMC5130_STANDALONE
+ * :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
+ */
+#define X_DRIVER_TYPE  TMC2130
+#define Y_DRIVER_TYPE  TMC2130
+#define Z_DRIVER_TYPE  TMC2130
+//#define X2_DRIVER_TYPE A4988
+//#define Y2_DRIVER_TYPE A4988
+//#define Z2_DRIVER_TYPE A4988
+#define E0_DRIVER_TYPE TMC2130
+//#define E1_DRIVER_TYPE A4988
+//#define E2_DRIVER_TYPE A4988
+//#define E3_DRIVER_TYPE A4988
+//#define E4_DRIVER_TYPE A4988
+
 // Enable this feature if all enabled endstop pins are interrupt-capable.
 // This will remove the need to poll the interrupt pins, saving many CPU cycles.
 //#define ENDSTOP_INTERRUPTS_FEATURE
--- a/Marlin/src/config/examples/UltiMachine/Archim2/Configuration_adv.h
+++ b/Marlin/src/config/examples/UltiMachine/Archim2/Configuration_adv.h
@ -837,15 +837,17 @@

 /**
 * Minimum delay after setting the stepper DIR (in ns)
- *    0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
- *   20 : Minimum for TMC2xxx drivers
- *  200 : Minimum for A4988 drivers
- *  500 : Minimum for LV8729 drivers (guess, no info in datasheet)
- *  650 : Minimum for DRV8825 drivers
- * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
- *15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *     0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
+ *    20 : Minimum for TMC2xxx drivers
+ *   200 : Minimum for A4988 drivers
+ *   500 : Minimum for LV8729 drivers (guess, no info in datasheet)
+ *   650 : Minimum for DRV8825 drivers
+ *  1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
+ * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_DIR_DELAY 0
+//#define MINIMUM_STEPPER_DIR_DELAY 650

 /**
 * Minimum stepper driver pulse width (in µs)
@ -855,8 +857,10 @@
 *   2 : Minimum for DRV8825 stepper drivers
 *   3 : Minimum for TB6600 stepper drivers
 *  30 : Minimum for TB6560 stepper drivers
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_PULSE 2
+//#define MINIMUM_STEPPER_PULSE 2

 /**
 * Maximum stepping rate (in Hz) the stepper driver allows
@ -867,8 +871,10 @@
 *  150000 : Maximum for TB6600 stepper driver
 *  130000 : Maximum for LV8729 stepper driver
 *   15000 : Maximum for TB6560 stepper driver
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MAXIMUM_STEPPER_RATE 250000
+//#define MAXIMUM_STEPPER_RATE 250000

 // @section temperature

@ -1036,23 +1042,12 @@
 // @section tmc

 /**
- * Enable this section if you have TMC26X motor drivers.
- * You will need to import the TMC26XStepper library into the Arduino IDE for this
- * (https://github.com/trinamic/TMC26XStepper.git)
+ * TMC26X Stepper Driver options
+ *
+ * The TMC26XStepper library is required for this stepper driver.
+ * https://github.com/trinamic/TMC26XStepper
 */
-//#define HAVE_TMC26X
-#if ENABLED(HAVE_TMC26X)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC26X
-  //#define X2_IS_TMC26X
-  //#define Y_IS_TMC26X
-  //#define Y2_IS_TMC26X
-  //#define Z_IS_TMC26X
-  //#define Z2_IS_TMC26X
-  //#define E0_IS_TMC26X
-  //#define E1_IS_TMC26X
-  //#define E2_IS_TMC26X
-  //#define E3_IS_TMC26X
-  //#define E4_IS_TMC26X
+#if HAS_DRIVER(TMC26X)

  #define X_MAX_CURRENT     1000 // in mA
  #define X_SENSE_RESISTOR    91 // in mOhms
@ -1098,62 +1093,29 @@
  #define E4_SENSE_RESISTOR   91
  #define E4_MICROSTEPS       16

-#endif
+#endif // TMC26X

 // @section tmc_smart

 /**
- * Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
- *
- * You'll also need the TMC2130Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2130Stepper).
- *
 * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
 * the hardware SPI interface on your board and define the required CS pins
 * in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
 * You may also use software SPI if you wish to use general purpose IO pins.
- */
-//#define HAVE_TMC2130
-#if ENABLED(HAVE_TMC2130)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2130
-  //#define X2_IS_TMC2130
-  //#define Y_IS_TMC2130
-  //#define Y2_IS_TMC2130
-  //#define Z_IS_TMC2130
-  //#define Z2_IS_TMC2130
-  //#define E0_IS_TMC2130
-  //#define E1_IS_TMC2130
-  //#define E2_IS_TMC2130
-  //#define E3_IS_TMC2130
-  //#define E4_IS_TMC2130
-#endif
-
-/**
- * Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
- * Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
+ *
+ * The TMC2130Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2130Stepper
+ *
+ * To use TMC2208 stepper UART-configurable stepper drivers
+ * connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
 * To use the reading capabilities, also connect #_SERIAL_RX_PIN
 * to PDN_UART without a resistor.
 * The drivers can also be used with hardware serial.
 *
- * You'll also need the TMC2208Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2208Stepper).
+ * The TMC2208Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2208Stepper
 */
-//#define HAVE_TMC2208
-#if ENABLED(HAVE_TMC2208)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2208
-  //#define X2_IS_TMC2208
-  //#define Y_IS_TMC2208
-  //#define Y2_IS_TMC2208
-  //#define Z_IS_TMC2208
-  //#define Z2_IS_TMC2208
-  //#define E0_IS_TMC2208
-  //#define E1_IS_TMC2208
-  //#define E2_IS_TMC2208
-  //#define E3_IS_TMC2208
-  //#define E4_IS_TMC2208
-#endif
-
-#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
+#if HAS_TRINAMIC

  #define R_SENSE           0.11  // R_sense resistor for SilentStepStick2130
  #define HOLD_MULTIPLIER    0.5  // Scales down the holding current from run current
@ -1308,25 +1270,12 @@
 // @section L6470

 /**
- * Enable this section if you have L6470 motor drivers.
- * You need to import the L6470 library into the Arduino IDE for this.
- * (https://github.com/ameyer/Arduino-L6470)
+ * L6470 Stepper Driver options
+ *
+ * The Arduino-L6470 library is required for this stepper driver.
+ * https://github.com/ameyer/Arduino-L6470
 */
-
-//#define HAVE_L6470DRIVER
-#if ENABLED(HAVE_L6470DRIVER)
-
-  //#define X_IS_L6470
-  //#define X2_IS_L6470
-  //#define Y_IS_L6470
-  //#define Y2_IS_L6470
-  //#define Z_IS_L6470
-  //#define Z2_IS_L6470
-  //#define E0_IS_L6470
-  //#define E1_IS_L6470
-  //#define E2_IS_L6470
-  //#define E3_IS_L6470
-  //#define E4_IS_L6470
+#if HAS_DRIVER(L6470)

  #define X_MICROSTEPS      16 // number of microsteps
  #define X_OVERCURRENT   2000 // maxc current in mA. If the current goes over this value, the driver will switch off
@ -1372,7 +1321,7 @@
  #define E4_OVERCURRENT  2000
  #define E4_STALLCURRENT 1500

-#endif
+#endif // L6470

 /**
 * TWI/I2C BUS
--- a/Marlin/src/config/examples/Velleman/K8200/Configuration.h
+++ b/Marlin/src/config/examples/Velleman/K8200/Configuration.h
@ -581,6 +581,29 @@
 #define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
 #define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.

+/**
+ * Specify Stepper Driver types
+ * The options are used to determine driver pulse timings as well as more advanced functionality.
+ * Stepper timing options can be overridden in Configuration_adv.h
+ *
+ * Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
+ *          TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
+ *          TMC26X,  TMC26X_STANDALONE,  TMC2660, TMC2660_STANDALONE,
+ *          TMC5130, TMC5130_STANDALONE
+ * :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
+ */
+#define X_DRIVER_TYPE  A4988
+#define Y_DRIVER_TYPE  A4988
+#define Z_DRIVER_TYPE  A4988
+#define X2_DRIVER_TYPE A4988
+#define Y2_DRIVER_TYPE A4988
+#define Z2_DRIVER_TYPE A4988
+#define E0_DRIVER_TYPE A4988
+#define E1_DRIVER_TYPE A4988
+#define E2_DRIVER_TYPE A4988
+#define E3_DRIVER_TYPE A4988
+#define E4_DRIVER_TYPE A4988
+
 // Enable this feature if all enabled endstop pins are interrupt-capable.
 // This will remove the need to poll the interrupt pins, saving many CPU cycles.
 //#define ENDSTOP_INTERRUPTS_FEATURE
--- a/Marlin/src/config/examples/Velleman/K8200/Configuration_adv.h
+++ b/Marlin/src/config/examples/Velleman/K8200/Configuration_adv.h
@ -840,15 +840,17 @@

 /**
 * Minimum delay after setting the stepper DIR (in ns)
- *    0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
- *   20 : Minimum for TMC2xxx drivers
- *  200 : Minimum for A4988 drivers
- *  500 : Minimum for LV8729 drivers (guess, no info in datasheet)
- *  650 : Minimum for DRV8825 drivers
- * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
- *15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *     0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
+ *    20 : Minimum for TMC2xxx drivers
+ *   200 : Minimum for A4988 drivers
+ *   500 : Minimum for LV8729 drivers (guess, no info in datasheet)
+ *   650 : Minimum for DRV8825 drivers
+ *  1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
+ * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_DIR_DELAY 0
+//#define MINIMUM_STEPPER_DIR_DELAY 650

 /**
 * Minimum stepper driver pulse width (in µs)
@ -858,8 +860,10 @@
 *   2 : Minimum for DRV8825 stepper drivers
 *   3 : Minimum for TB6600 stepper drivers
 *  30 : Minimum for TB6560 stepper drivers
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_PULSE 2
+//#define MINIMUM_STEPPER_PULSE 2

 /**
 * Maximum stepping rate (in Hz) the stepper driver allows
@ -870,8 +874,10 @@
 *  150000 : Maximum for TB6600 stepper driver
 *  130000 : Maximum for LV8729 stepper driver
 *   15000 : Maximum for TB6560 stepper driver
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MAXIMUM_STEPPER_RATE 250000
+//#define MAXIMUM_STEPPER_RATE 250000

 // @section temperature

@ -1039,23 +1045,12 @@
 // @section tmc

 /**
- * Enable this section if you have TMC26X motor drivers.
- * You will need to import the TMC26XStepper library into the Arduino IDE for this
- * (https://github.com/trinamic/TMC26XStepper.git)
+ * TMC26X Stepper Driver options
+ *
+ * The TMC26XStepper library is required for this stepper driver.
+ * https://github.com/trinamic/TMC26XStepper
 */
-//#define HAVE_TMC26X
-#if ENABLED(HAVE_TMC26X)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC26X
-  //#define X2_IS_TMC26X
-  //#define Y_IS_TMC26X
-  //#define Y2_IS_TMC26X
-  //#define Z_IS_TMC26X
-  //#define Z2_IS_TMC26X
-  //#define E0_IS_TMC26X
-  //#define E1_IS_TMC26X
-  //#define E2_IS_TMC26X
-  //#define E3_IS_TMC26X
-  //#define E4_IS_TMC26X
+#if HAS_DRIVER(TMC26X)

  #define X_MAX_CURRENT     1000 // in mA
  #define X_SENSE_RESISTOR    91 // in mOhms
@ -1101,62 +1096,29 @@
  #define E4_SENSE_RESISTOR   91
  #define E4_MICROSTEPS       16

-#endif
+#endif // TMC26X

 // @section tmc_smart

 /**
- * Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
- *
- * You'll also need the TMC2130Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2130Stepper).
- *
 * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
 * the hardware SPI interface on your board and define the required CS pins
 * in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
 * You may also use software SPI if you wish to use general purpose IO pins.
- */
-//#define HAVE_TMC2130
-#if ENABLED(HAVE_TMC2130)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2130
-  //#define X2_IS_TMC2130
-  //#define Y_IS_TMC2130
-  //#define Y2_IS_TMC2130
-  //#define Z_IS_TMC2130
-  //#define Z2_IS_TMC2130
-  //#define E0_IS_TMC2130
-  //#define E1_IS_TMC2130
-  //#define E2_IS_TMC2130
-  //#define E3_IS_TMC2130
-  //#define E4_IS_TMC2130
-#endif
-
-/**
- * Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
- * Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
+ *
+ * The TMC2130Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2130Stepper
+ *
+ * To use TMC2208 stepper UART-configurable stepper drivers
+ * connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
 * To use the reading capabilities, also connect #_SERIAL_RX_PIN
 * to PDN_UART without a resistor.
 * The drivers can also be used with hardware serial.
 *
- * You'll also need the TMC2208Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2208Stepper).
+ * The TMC2208Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2208Stepper
 */
-//#define HAVE_TMC2208
-#if ENABLED(HAVE_TMC2208)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2208
-  //#define X2_IS_TMC2208
-  //#define Y_IS_TMC2208
-  //#define Y2_IS_TMC2208
-  //#define Z_IS_TMC2208
-  //#define Z2_IS_TMC2208
-  //#define E0_IS_TMC2208
-  //#define E1_IS_TMC2208
-  //#define E2_IS_TMC2208
-  //#define E3_IS_TMC2208
-  //#define E4_IS_TMC2208
-#endif
-
-#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
+#if HAS_TRINAMIC

  #define R_SENSE           0.11  // R_sense resistor for SilentStepStick2130
  #define HOLD_MULTIPLIER    0.5  // Scales down the holding current from run current
@ -1311,25 +1273,12 @@
 // @section L6470

 /**
- * Enable this section if you have L6470 motor drivers.
- * You need to import the L6470 library into the Arduino IDE for this.
- * (https://github.com/ameyer/Arduino-L6470)
+ * L6470 Stepper Driver options
+ *
+ * The Arduino-L6470 library is required for this stepper driver.
+ * https://github.com/ameyer/Arduino-L6470
 */
-
-//#define HAVE_L6470DRIVER
-#if ENABLED(HAVE_L6470DRIVER)
-
-  //#define X_IS_L6470
-  //#define X2_IS_L6470
-  //#define Y_IS_L6470
-  //#define Y2_IS_L6470
-  //#define Z_IS_L6470
-  //#define Z2_IS_L6470
-  //#define E0_IS_L6470
-  //#define E1_IS_L6470
-  //#define E2_IS_L6470
-  //#define E3_IS_L6470
-  //#define E4_IS_L6470
+#if HAS_DRIVER(L6470)

  #define X_MICROSTEPS      16 // number of microsteps
  #define X_OVERCURRENT   2000 // maxc current in mA. If the current goes over this value, the driver will switch off
@ -1375,7 +1324,7 @@
  #define E4_OVERCURRENT  2000
  #define E4_STALLCURRENT 1500

-#endif
+#endif // L6470

 /**
 * TWI/I2C BUS
--- a/Marlin/src/config/examples/Velleman/K8400/Configuration_adv.h
+++ b/Marlin/src/config/examples/Velleman/K8400/Configuration_adv.h
@ -837,15 +837,17 @@

 /**
 * Minimum delay after setting the stepper DIR (in ns)
- *    0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
- *   20 : Minimum for TMC2xxx drivers
- *  200 : Minimum for A4988 drivers
- *  500 : Minimum for LV8729 drivers (guess, no info in datasheet)
- *  650 : Minimum for DRV8825 drivers
- * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
- *15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *     0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
+ *    20 : Minimum for TMC2xxx drivers
+ *   200 : Minimum for A4988 drivers
+ *   500 : Minimum for LV8729 drivers (guess, no info in datasheet)
+ *   650 : Minimum for DRV8825 drivers
+ *  1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
+ * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_DIR_DELAY 0
+//#define MINIMUM_STEPPER_DIR_DELAY 650

 /**
 * Minimum stepper driver pulse width (in µs)
@ -855,8 +857,10 @@
 *   2 : Minimum for DRV8825 stepper drivers
 *   3 : Minimum for TB6600 stepper drivers
 *  30 : Minimum for TB6560 stepper drivers
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_PULSE 2
+//#define MINIMUM_STEPPER_PULSE 2

 /**
 * Maximum stepping rate (in Hz) the stepper driver allows
@ -867,8 +871,10 @@
 *  150000 : Maximum for TB6600 stepper driver
 *  130000 : Maximum for LV8729 stepper driver
 *   15000 : Maximum for TB6560 stepper driver
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MAXIMUM_STEPPER_RATE 250000
+//#define MAXIMUM_STEPPER_RATE 250000

 // @section temperature

@ -1036,23 +1042,12 @@
 // @section tmc

 /**
- * Enable this section if you have TMC26X motor drivers.
- * You will need to import the TMC26XStepper library into the Arduino IDE for this
- * (https://github.com/trinamic/TMC26XStepper.git)
+ * TMC26X Stepper Driver options
+ *
+ * The TMC26XStepper library is required for this stepper driver.
+ * https://github.com/trinamic/TMC26XStepper
 */
-//#define HAVE_TMC26X
-#if ENABLED(HAVE_TMC26X)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC26X
-  //#define X2_IS_TMC26X
-  //#define Y_IS_TMC26X
-  //#define Y2_IS_TMC26X
-  //#define Z_IS_TMC26X
-  //#define Z2_IS_TMC26X
-  //#define E0_IS_TMC26X
-  //#define E1_IS_TMC26X
-  //#define E2_IS_TMC26X
-  //#define E3_IS_TMC26X
-  //#define E4_IS_TMC26X
+#if HAS_DRIVER(TMC26X)

  #define X_MAX_CURRENT     1000 // in mA
  #define X_SENSE_RESISTOR    91 // in mOhms
@ -1098,62 +1093,29 @@
  #define E4_SENSE_RESISTOR   91
  #define E4_MICROSTEPS       16

-#endif
+#endif // TMC26X

 // @section tmc_smart

 /**
- * Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
- *
- * You'll also need the TMC2130Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2130Stepper).
- *
 * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
 * the hardware SPI interface on your board and define the required CS pins
 * in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
 * You may also use software SPI if you wish to use general purpose IO pins.
- */
-//#define HAVE_TMC2130
-#if ENABLED(HAVE_TMC2130)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2130
-  //#define X2_IS_TMC2130
-  //#define Y_IS_TMC2130
-  //#define Y2_IS_TMC2130
-  //#define Z_IS_TMC2130
-  //#define Z2_IS_TMC2130
-  //#define E0_IS_TMC2130
-  //#define E1_IS_TMC2130
-  //#define E2_IS_TMC2130
-  //#define E3_IS_TMC2130
-  //#define E4_IS_TMC2130
-#endif
-
-/**
- * Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
- * Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
+ *
+ * The TMC2130Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2130Stepper
+ *
+ * To use TMC2208 stepper UART-configurable stepper drivers
+ * connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
 * To use the reading capabilities, also connect #_SERIAL_RX_PIN
 * to PDN_UART without a resistor.
 * The drivers can also be used with hardware serial.
 *
- * You'll also need the TMC2208Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2208Stepper).
+ * The TMC2208Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2208Stepper
 */
-//#define HAVE_TMC2208
-#if ENABLED(HAVE_TMC2208)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2208
-  //#define X2_IS_TMC2208
-  //#define Y_IS_TMC2208
-  //#define Y2_IS_TMC2208
-  //#define Z_IS_TMC2208
-  //#define Z2_IS_TMC2208
-  //#define E0_IS_TMC2208
-  //#define E1_IS_TMC2208
-  //#define E2_IS_TMC2208
-  //#define E3_IS_TMC2208
-  //#define E4_IS_TMC2208
-#endif
-
-#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
+#if HAS_TRINAMIC

  #define R_SENSE           0.11  // R_sense resistor for SilentStepStick2130
  #define HOLD_MULTIPLIER    0.5  // Scales down the holding current from run current
@ -1308,25 +1270,12 @@
 // @section L6470

 /**
- * Enable this section if you have L6470 motor drivers.
- * You need to import the L6470 library into the Arduino IDE for this.
- * (https://github.com/ameyer/Arduino-L6470)
+ * L6470 Stepper Driver options
+ *
+ * The Arduino-L6470 library is required for this stepper driver.
+ * https://github.com/ameyer/Arduino-L6470
 */
-
-//#define HAVE_L6470DRIVER
-#if ENABLED(HAVE_L6470DRIVER)
-
-  //#define X_IS_L6470
-  //#define X2_IS_L6470
-  //#define Y_IS_L6470
-  //#define Y2_IS_L6470
-  //#define Z_IS_L6470
-  //#define Z2_IS_L6470
-  //#define E0_IS_L6470
-  //#define E1_IS_L6470
-  //#define E2_IS_L6470
-  //#define E3_IS_L6470
-  //#define E4_IS_L6470
+#if HAS_DRIVER(L6470)

  #define X_MICROSTEPS      16 // number of microsteps
  #define X_OVERCURRENT   2000 // maxc current in mA. If the current goes over this value, the driver will switch off
@ -1372,7 +1321,7 @@
  #define E4_OVERCURRENT  2000
  #define E4_STALLCURRENT 1500

-#endif
+#endif // L6470

 /**
 * TWI/I2C BUS
--- a/Marlin/src/config/examples/Wanhao/Duplicator
+++ b/Marlin/src/config/examples/Wanhao/Duplicator
@ -561,6 +561,29 @@
 #define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
 #define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.

+/**
+ * Specify Stepper Driver types
+ * The options are used to determine driver pulse timings as well as more advanced functionality.
+ * Stepper timing options can be overridden in Configuration_adv.h
+ *
+ * Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
+ *          TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
+ *          TMC26X,  TMC26X_STANDALONE,  TMC2660, TMC2660_STANDALONE,
+ *          TMC5130, TMC5130_STANDALONE
+ * :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
+ */
+#define X_DRIVER_TYPE  A4988
+#define Y_DRIVER_TYPE  A4988
+#define Z_DRIVER_TYPE  A4988
+#define X2_DRIVER_TYPE A4988
+#define Y2_DRIVER_TYPE A4988
+#define Z2_DRIVER_TYPE A4988
+#define E0_DRIVER_TYPE A4988
+#define E1_DRIVER_TYPE A4988
+#define E2_DRIVER_TYPE A4988
+#define E3_DRIVER_TYPE A4988
+#define E4_DRIVER_TYPE A4988
+
 // Enable this feature if all enabled endstop pins are interrupt-capable.
 // This will remove the need to poll the interrupt pins, saving many CPU cycles.
 //#define ENDSTOP_INTERRUPTS_FEATURE
--- a/Marlin/src/config/examples/Wanhao/Duplicator
+++ b/Marlin/src/config/examples/Wanhao/Duplicator
@ -839,15 +839,17 @@

 /**
 * Minimum delay after setting the stepper DIR (in ns)
- *    0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
- *   20 : Minimum for TMC2xxx drivers
- *  200 : Minimum for A4988 drivers
- *  500 : Minimum for LV8729 drivers (guess, no info in datasheet)
- *  650 : Minimum for DRV8825 drivers
- * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
- *15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *     0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
+ *    20 : Minimum for TMC2xxx drivers
+ *   200 : Minimum for A4988 drivers
+ *   500 : Minimum for LV8729 drivers (guess, no info in datasheet)
+ *   650 : Minimum for DRV8825 drivers
+ *  1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
+ * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_DIR_DELAY 0
+//#define MINIMUM_STEPPER_DIR_DELAY 650

 /**
 * Minimum stepper driver pulse width (in µs)
@ -857,8 +859,10 @@
 *   2 : Minimum for DRV8825 stepper drivers
 *   3 : Minimum for TB6600 stepper drivers
 *  30 : Minimum for TB6560 stepper drivers
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_PULSE 2
+//#define MINIMUM_STEPPER_PULSE 2

 /**
 * Maximum stepping rate (in Hz) the stepper driver allows
@ -869,8 +873,10 @@
 *  150000 : Maximum for TB6600 stepper driver
 *  130000 : Maximum for LV8729 stepper driver
 *   15000 : Maximum for TB6560 stepper driver
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MAXIMUM_STEPPER_RATE 250000
+//#define MAXIMUM_STEPPER_RATE 250000

 // @section temperature

@ -1038,23 +1044,12 @@
 // @section tmc

 /**
- * Enable this section if you have TMC26X motor drivers.
- * You will need to import the TMC26XStepper library into the Arduino IDE for this
- * (https://github.com/trinamic/TMC26XStepper.git)
+ * TMC26X Stepper Driver options
+ *
+ * The TMC26XStepper library is required for this stepper driver.
+ * https://github.com/trinamic/TMC26XStepper
 */
-//#define HAVE_TMC26X
-#if ENABLED(HAVE_TMC26X)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC26X
-  //#define X2_IS_TMC26X
-  //#define Y_IS_TMC26X
-  //#define Y2_IS_TMC26X
-  //#define Z_IS_TMC26X
-  //#define Z2_IS_TMC26X
-  //#define E0_IS_TMC26X
-  //#define E1_IS_TMC26X
-  //#define E2_IS_TMC26X
-  //#define E3_IS_TMC26X
-  //#define E4_IS_TMC26X
+#if HAS_DRIVER(TMC26X)

  #define X_MAX_CURRENT     1000 // in mA
  #define X_SENSE_RESISTOR    91 // in mOhms
@ -1100,62 +1095,29 @@
  #define E4_SENSE_RESISTOR   91
  #define E4_MICROSTEPS       16

-#endif
+#endif // TMC26X

 // @section tmc_smart

 /**
- * Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
- *
- * You'll also need the TMC2130Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2130Stepper).
- *
 * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
 * the hardware SPI interface on your board and define the required CS pins
 * in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
 * You may also use software SPI if you wish to use general purpose IO pins.
- */
-//#define HAVE_TMC2130
-#if ENABLED(HAVE_TMC2130)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2130
-  //#define X2_IS_TMC2130
-  //#define Y_IS_TMC2130
-  //#define Y2_IS_TMC2130
-  //#define Z_IS_TMC2130
-  //#define Z2_IS_TMC2130
-  //#define E0_IS_TMC2130
-  //#define E1_IS_TMC2130
-  //#define E2_IS_TMC2130
-  //#define E3_IS_TMC2130
-  //#define E4_IS_TMC2130
-#endif
-
-/**
- * Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
- * Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
+ *
+ * The TMC2130Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2130Stepper
+ *
+ * To use TMC2208 stepper UART-configurable stepper drivers
+ * connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
 * To use the reading capabilities, also connect #_SERIAL_RX_PIN
 * to PDN_UART without a resistor.
 * The drivers can also be used with hardware serial.
 *
- * You'll also need the TMC2208Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2208Stepper).
+ * The TMC2208Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2208Stepper
 */
-//#define HAVE_TMC2208
-#if ENABLED(HAVE_TMC2208)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2208
-  //#define X2_IS_TMC2208
-  //#define Y_IS_TMC2208
-  //#define Y2_IS_TMC2208
-  //#define Z_IS_TMC2208
-  //#define Z2_IS_TMC2208
-  //#define E0_IS_TMC2208
-  //#define E1_IS_TMC2208
-  //#define E2_IS_TMC2208
-  //#define E3_IS_TMC2208
-  //#define E4_IS_TMC2208
-#endif
-
-#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
+#if HAS_TRINAMIC

  #define R_SENSE           0.11  // R_sense resistor for SilentStepStick2130
  #define HOLD_MULTIPLIER    0.5  // Scales down the holding current from run current
@ -1310,25 +1272,12 @@
 // @section L6470

 /**
- * Enable this section if you have L6470 motor drivers.
- * You need to import the L6470 library into the Arduino IDE for this.
- * (https://github.com/ameyer/Arduino-L6470)
+ * L6470 Stepper Driver options
+ *
+ * The Arduino-L6470 library is required for this stepper driver.
+ * https://github.com/ameyer/Arduino-L6470
 */
-
-//#define HAVE_L6470DRIVER
-#if ENABLED(HAVE_L6470DRIVER)
-
-  //#define X_IS_L6470
-  //#define X2_IS_L6470
-  //#define Y_IS_L6470
-  //#define Y2_IS_L6470
-  //#define Z_IS_L6470
-  //#define Z2_IS_L6470
-  //#define E0_IS_L6470
-  //#define E1_IS_L6470
-  //#define E2_IS_L6470
-  //#define E3_IS_L6470
-  //#define E4_IS_L6470
+#if HAS_DRIVER(L6470)

  #define X_MICROSTEPS      16 // number of microsteps
  #define X_OVERCURRENT   2000 // maxc current in mA. If the current goes over this value, the driver will switch off
@ -1374,7 +1323,7 @@
  #define E4_OVERCURRENT  2000
  #define E4_STALLCURRENT 1500

-#endif
+#endif // L6470

 /**
 * TWI/I2C BUS
--- a/Marlin/src/config/examples/adafruit/ST7565/Configuration.h
+++ b/Marlin/src/config/examples/adafruit/ST7565/Configuration.h
@ -551,6 +551,29 @@
 #define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
 #define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.

+/**
+ * Specify Stepper Driver types
+ * The options are used to determine driver pulse timings as well as more advanced functionality.
+ * Stepper timing options can be overridden in Configuration_adv.h
+ *
+ * Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
+ *          TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
+ *          TMC26X,  TMC26X_STANDALONE,  TMC2660, TMC2660_STANDALONE,
+ *          TMC5130, TMC5130_STANDALONE
+ * :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
+ */
+#define X_DRIVER_TYPE  A4988
+#define Y_DRIVER_TYPE  A4988
+#define Z_DRIVER_TYPE  A4988
+#define X2_DRIVER_TYPE A4988
+#define Y2_DRIVER_TYPE A4988
+#define Z2_DRIVER_TYPE A4988
+#define E0_DRIVER_TYPE A4988
+#define E1_DRIVER_TYPE A4988
+#define E2_DRIVER_TYPE A4988
+#define E3_DRIVER_TYPE A4988
+#define E4_DRIVER_TYPE A4988
+
 // Enable this feature if all enabled endstop pins are interrupt-capable.
 // This will remove the need to poll the interrupt pins, saving many CPU cycles.
 //#define ENDSTOP_INTERRUPTS_FEATURE
--- a/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h
+++ b/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h
@ -839,15 +839,17 @@

 /**
 * Minimum delay after setting the stepper DIR (in ns)
- *    0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
- *   20 : Minimum for TMC2xxx drivers
- *  200 : Minimum for A4988 drivers
- *  500 : Minimum for LV8729 drivers (guess, no info in datasheet)
- *  650 : Minimum for DRV8825 drivers
- * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
- *15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *     0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
+ *    20 : Minimum for TMC2xxx drivers
+ *   200 : Minimum for A4988 drivers
+ *   500 : Minimum for LV8729 drivers (guess, no info in datasheet)
+ *   650 : Minimum for DRV8825 drivers
+ *  1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
+ * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_DIR_DELAY 0
+//#define MINIMUM_STEPPER_DIR_DELAY 650

 /**
 * Minimum stepper driver pulse width (in µs)
@ -857,8 +859,10 @@
 *   2 : Minimum for DRV8825 stepper drivers
 *   3 : Minimum for TB6600 stepper drivers
 *  30 : Minimum for TB6560 stepper drivers
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_PULSE 2
+//#define MINIMUM_STEPPER_PULSE 2

 /**
 * Maximum stepping rate (in Hz) the stepper driver allows
@ -869,8 +873,10 @@
 *  150000 : Maximum for TB6600 stepper driver
 *  130000 : Maximum for LV8729 stepper driver
 *   15000 : Maximum for TB6560 stepper driver
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MAXIMUM_STEPPER_RATE 250000
+//#define MAXIMUM_STEPPER_RATE 250000

 // @section temperature

@ -1038,23 +1044,12 @@
 // @section tmc

 /**
- * Enable this section if you have TMC26X motor drivers.
- * You will need to import the TMC26XStepper library into the Arduino IDE for this
- * (https://github.com/trinamic/TMC26XStepper.git)
+ * TMC26X Stepper Driver options
+ *
+ * The TMC26XStepper library is required for this stepper driver.
+ * https://github.com/trinamic/TMC26XStepper
 */
-//#define HAVE_TMC26X
-#if ENABLED(HAVE_TMC26X)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC26X
-  //#define X2_IS_TMC26X
-  //#define Y_IS_TMC26X
-  //#define Y2_IS_TMC26X
-  //#define Z_IS_TMC26X
-  //#define Z2_IS_TMC26X
-  //#define E0_IS_TMC26X
-  //#define E1_IS_TMC26X
-  //#define E2_IS_TMC26X
-  //#define E3_IS_TMC26X
-  //#define E4_IS_TMC26X
+#if HAS_DRIVER(TMC26X)

  #define X_MAX_CURRENT     1000 // in mA
  #define X_SENSE_RESISTOR    91 // in mOhms
@ -1100,62 +1095,29 @@
  #define E4_SENSE_RESISTOR   91
  #define E4_MICROSTEPS       16

-#endif
+#endif // TMC26X

 // @section tmc_smart

 /**
- * Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
- *
- * You'll also need the TMC2130Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2130Stepper).
- *
 * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
 * the hardware SPI interface on your board and define the required CS pins
 * in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
 * You may also use software SPI if you wish to use general purpose IO pins.
- */
-//#define HAVE_TMC2130
-#if ENABLED(HAVE_TMC2130)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2130
-  //#define X2_IS_TMC2130
-  //#define Y_IS_TMC2130
-  //#define Y2_IS_TMC2130
-  //#define Z_IS_TMC2130
-  //#define Z2_IS_TMC2130
-  //#define E0_IS_TMC2130
-  //#define E1_IS_TMC2130
-  //#define E2_IS_TMC2130
-  //#define E3_IS_TMC2130
-  //#define E4_IS_TMC2130
-#endif
-
-/**
- * Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
- * Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
+ *
+ * The TMC2130Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2130Stepper
+ *
+ * To use TMC2208 stepper UART-configurable stepper drivers
+ * connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
 * To use the reading capabilities, also connect #_SERIAL_RX_PIN
 * to PDN_UART without a resistor.
 * The drivers can also be used with hardware serial.
 *
- * You'll also need the TMC2208Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2208Stepper).
+ * The TMC2208Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2208Stepper
 */
-//#define HAVE_TMC2208
-#if ENABLED(HAVE_TMC2208)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2208
-  //#define X2_IS_TMC2208
-  //#define Y_IS_TMC2208
-  //#define Y2_IS_TMC2208
-  //#define Z_IS_TMC2208
-  //#define Z2_IS_TMC2208
-  //#define E0_IS_TMC2208
-  //#define E1_IS_TMC2208
-  //#define E2_IS_TMC2208
-  //#define E3_IS_TMC2208
-  //#define E4_IS_TMC2208
-#endif
-
-#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
+#if HAS_TRINAMIC

  #define R_SENSE           0.11  // R_sense resistor for SilentStepStick2130
  #define HOLD_MULTIPLIER    0.5  // Scales down the holding current from run current
@ -1310,25 +1272,12 @@
 // @section L6470

 /**
- * Enable this section if you have L6470 motor drivers.
- * You need to import the L6470 library into the Arduino IDE for this.
- * (https://github.com/ameyer/Arduino-L6470)
+ * L6470 Stepper Driver options
+ *
+ * The Arduino-L6470 library is required for this stepper driver.
+ * https://github.com/ameyer/Arduino-L6470
 */
-
-//#define HAVE_L6470DRIVER
-#if ENABLED(HAVE_L6470DRIVER)
-
-  //#define X_IS_L6470
-  //#define X2_IS_L6470
-  //#define Y_IS_L6470
-  //#define Y2_IS_L6470
-  //#define Z_IS_L6470
-  //#define Z2_IS_L6470
-  //#define E0_IS_L6470
-  //#define E1_IS_L6470
-  //#define E2_IS_L6470
-  //#define E3_IS_L6470
-  //#define E4_IS_L6470
+#if HAS_DRIVER(L6470)

  #define X_MICROSTEPS      16 // number of microsteps
  #define X_OVERCURRENT   2000 // maxc current in mA. If the current goes over this value, the driver will switch off
@ -1374,7 +1323,7 @@
  #define E4_OVERCURRENT  2000
  #define E4_STALLCURRENT 1500

-#endif
+#endif // L6470

 /**
 * TWI/I2C BUS
--- a/Marlin/src/config/examples/delta/FLSUN/kossel/Configuration_adv.h
+++ b/Marlin/src/config/examples/delta/FLSUN/kossel/Configuration_adv.h
@ -839,15 +839,17 @@

 /**
 * Minimum delay after setting the stepper DIR (in ns)
- *    0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
- *   20 : Minimum for TMC2xxx drivers
- *  200 : Minimum for A4988 drivers
- *  500 : Minimum for LV8729 drivers (guess, no info in datasheet)
- *  650 : Minimum for DRV8825 drivers
- * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
- *15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *     0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
+ *    20 : Minimum for TMC2xxx drivers
+ *   200 : Minimum for A4988 drivers
+ *   500 : Minimum for LV8729 drivers (guess, no info in datasheet)
+ *   650 : Minimum for DRV8825 drivers
+ *  1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
+ * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_DIR_DELAY 0
+//#define MINIMUM_STEPPER_DIR_DELAY 650

 /**
 * Minimum stepper driver pulse width (in µs)
@ -857,8 +859,10 @@
 *   2 : Minimum for DRV8825 stepper drivers
 *   3 : Minimum for TB6600 stepper drivers
 *  30 : Minimum for TB6560 stepper drivers
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_PULSE 2
+//#define MINIMUM_STEPPER_PULSE 2

 /**
 * Maximum stepping rate (in Hz) the stepper driver allows
@ -869,8 +873,10 @@
 *  150000 : Maximum for TB6600 stepper driver
 *  130000 : Maximum for LV8729 stepper driver
 *   15000 : Maximum for TB6560 stepper driver
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MAXIMUM_STEPPER_RATE 250000
+//#define MAXIMUM_STEPPER_RATE 250000

 // @section temperature

@ -1038,23 +1044,12 @@
 // @section tmc

 /**
- * Enable this section if you have TMC26X motor drivers.
- * You will need to import the TMC26XStepper library into the Arduino IDE for this
- * (https://github.com/trinamic/TMC26XStepper.git)
+ * TMC26X Stepper Driver options
+ *
+ * The TMC26XStepper library is required for this stepper driver.
+ * https://github.com/trinamic/TMC26XStepper
 */
-//#define HAVE_TMC26X
-#if ENABLED(HAVE_TMC26X)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC26X
-  //#define X2_IS_TMC26X
-  //#define Y_IS_TMC26X
-  //#define Y2_IS_TMC26X
-  //#define Z_IS_TMC26X
-  //#define Z2_IS_TMC26X
-  //#define E0_IS_TMC26X
-  //#define E1_IS_TMC26X
-  //#define E2_IS_TMC26X
-  //#define E3_IS_TMC26X
-  //#define E4_IS_TMC26X
+#if HAS_DRIVER(TMC26X)

  #define X_MAX_CURRENT     1000 // in mA
  #define X_SENSE_RESISTOR    91 // in mOhms
@ -1100,62 +1095,29 @@
  #define E4_SENSE_RESISTOR   91
  #define E4_MICROSTEPS       16

-#endif
+#endif // TMC26X

 // @section tmc_smart

 /**
- * Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
- *
- * You'll also need the TMC2130Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2130Stepper).
- *
 * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
 * the hardware SPI interface on your board and define the required CS pins
 * in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
 * You may also use software SPI if you wish to use general purpose IO pins.
- */
-//#define HAVE_TMC2130
-#if ENABLED(HAVE_TMC2130)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2130
-  //#define X2_IS_TMC2130
-  //#define Y_IS_TMC2130
-  //#define Y2_IS_TMC2130
-  //#define Z_IS_TMC2130
-  //#define Z2_IS_TMC2130
-  //#define E0_IS_TMC2130
-  //#define E1_IS_TMC2130
-  //#define E2_IS_TMC2130
-  //#define E3_IS_TMC2130
-  //#define E4_IS_TMC2130
-#endif
-
-/**
- * Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
- * Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
+ *
+ * The TMC2130Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2130Stepper
+ *
+ * To use TMC2208 stepper UART-configurable stepper drivers
+ * connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
 * To use the reading capabilities, also connect #_SERIAL_RX_PIN
 * to PDN_UART without a resistor.
 * The drivers can also be used with hardware serial.
 *
- * You'll also need the TMC2208Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2208Stepper).
+ * The TMC2208Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2208Stepper
 */
-//#define HAVE_TMC2208
-#if ENABLED(HAVE_TMC2208)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2208
-  //#define X2_IS_TMC2208
-  //#define Y_IS_TMC2208
-  //#define Y2_IS_TMC2208
-  //#define Z_IS_TMC2208
-  //#define Z2_IS_TMC2208
-  //#define E0_IS_TMC2208
-  //#define E1_IS_TMC2208
-  //#define E2_IS_TMC2208
-  //#define E3_IS_TMC2208
-  //#define E4_IS_TMC2208
-#endif
-
-#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
+#if HAS_TRINAMIC

  #define R_SENSE           0.11  // R_sense resistor for SilentStepStick2130
  #define HOLD_MULTIPLIER    0.5  // Scales down the holding current from run current
@ -1310,25 +1272,12 @@
 // @section L6470

 /**
- * Enable this section if you have L6470 motor drivers.
- * You need to import the L6470 library into the Arduino IDE for this.
- * (https://github.com/ameyer/Arduino-L6470)
+ * L6470 Stepper Driver options
+ *
+ * The Arduino-L6470 library is required for this stepper driver.
+ * https://github.com/ameyer/Arduino-L6470
 */
-
-//#define HAVE_L6470DRIVER
-#if ENABLED(HAVE_L6470DRIVER)
-
-  //#define X_IS_L6470
-  //#define X2_IS_L6470
-  //#define Y_IS_L6470
-  //#define Y2_IS_L6470
-  //#define Z_IS_L6470
-  //#define Z2_IS_L6470
-  //#define E0_IS_L6470
-  //#define E1_IS_L6470
-  //#define E2_IS_L6470
-  //#define E3_IS_L6470
-  //#define E4_IS_L6470
+#if HAS_DRIVER(L6470)

  #define X_MICROSTEPS      16 // number of microsteps
  #define X_OVERCURRENT   2000 // maxc current in mA. If the current goes over this value, the driver will switch off
@ -1374,7 +1323,7 @@
  #define E4_OVERCURRENT  2000
  #define E4_STALLCURRENT 1500

-#endif
+#endif // L6470

 /**
 * TWI/I2C BUS
--- a/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration.h
+++ b/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration.h
@ -627,6 +627,29 @@
 #define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
 #define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.

+/**
+ * Specify Stepper Driver types
+ * The options are used to determine driver pulse timings as well as more advanced functionality.
+ * Stepper timing options can be overridden in Configuration_adv.h
+ *
+ * Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
+ *          TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
+ *          TMC26X,  TMC26X_STANDALONE,  TMC2660, TMC2660_STANDALONE,
+ *          TMC5130, TMC5130_STANDALONE
+ * :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
+ */
+#define X_DRIVER_TYPE  A4988
+#define Y_DRIVER_TYPE  A4988
+#define Z_DRIVER_TYPE  A4988
+#define X2_DRIVER_TYPE A4988
+#define Y2_DRIVER_TYPE A4988
+#define Z2_DRIVER_TYPE A4988
+#define E0_DRIVER_TYPE A4988
+#define E1_DRIVER_TYPE A4988
+#define E2_DRIVER_TYPE A4988
+#define E3_DRIVER_TYPE A4988
+#define E4_DRIVER_TYPE A4988
+
 // Enable this feature if all enabled endstop pins are interrupt-capable.
 // This will remove the need to poll the interrupt pins, saving many CPU cycles.
 //#define ENDSTOP_INTERRUPTS_FEATURE
--- a/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h
+++ b/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h
@ -839,15 +839,17 @@

 /**
 * Minimum delay after setting the stepper DIR (in ns)
- *    0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
- *   20 : Minimum for TMC2xxx drivers
- *  200 : Minimum for A4988 drivers
- *  500 : Minimum for LV8729 drivers (guess, no info in datasheet)
- *  650 : Minimum for DRV8825 drivers
- * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
- *15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *     0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
+ *    20 : Minimum for TMC2xxx drivers
+ *   200 : Minimum for A4988 drivers
+ *   500 : Minimum for LV8729 drivers (guess, no info in datasheet)
+ *   650 : Minimum for DRV8825 drivers
+ *  1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
+ * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_DIR_DELAY 0
+//#define MINIMUM_STEPPER_DIR_DELAY 650

 /**
 * Minimum stepper driver pulse width (in µs)
@ -857,8 +859,10 @@
 *   2 : Minimum for DRV8825 stepper drivers
 *   3 : Minimum for TB6600 stepper drivers
 *  30 : Minimum for TB6560 stepper drivers
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_PULSE 2
+//#define MINIMUM_STEPPER_PULSE 2

 /**
 * Maximum stepping rate (in Hz) the stepper driver allows
@ -869,8 +873,10 @@
 *  150000 : Maximum for TB6600 stepper driver
 *  130000 : Maximum for LV8729 stepper driver
 *   15000 : Maximum for TB6560 stepper driver
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MAXIMUM_STEPPER_RATE 250000
+//#define MAXIMUM_STEPPER_RATE 250000

 // @section temperature

@ -1038,23 +1044,12 @@
 // @section tmc

 /**
- * Enable this section if you have TMC26X motor drivers.
- * You will need to import the TMC26XStepper library into the Arduino IDE for this
- * (https://github.com/trinamic/TMC26XStepper.git)
+ * TMC26X Stepper Driver options
+ *
+ * The TMC26XStepper library is required for this stepper driver.
+ * https://github.com/trinamic/TMC26XStepper
 */
-//#define HAVE_TMC26X
-#if ENABLED(HAVE_TMC26X)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC26X
-  //#define X2_IS_TMC26X
-  //#define Y_IS_TMC26X
-  //#define Y2_IS_TMC26X
-  //#define Z_IS_TMC26X
-  //#define Z2_IS_TMC26X
-  //#define E0_IS_TMC26X
-  //#define E1_IS_TMC26X
-  //#define E2_IS_TMC26X
-  //#define E3_IS_TMC26X
-  //#define E4_IS_TMC26X
+#if HAS_DRIVER(TMC26X)

  #define X_MAX_CURRENT     1000 // in mA
  #define X_SENSE_RESISTOR    91 // in mOhms
@ -1100,62 +1095,29 @@
  #define E4_SENSE_RESISTOR   91
  #define E4_MICROSTEPS       16

-#endif
+#endif // TMC26X

 // @section tmc_smart

 /**
- * Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
- *
- * You'll also need the TMC2130Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2130Stepper).
- *
 * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
 * the hardware SPI interface on your board and define the required CS pins
 * in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
 * You may also use software SPI if you wish to use general purpose IO pins.
- */
-//#define HAVE_TMC2130
-#if ENABLED(HAVE_TMC2130)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2130
-  //#define X2_IS_TMC2130
-  //#define Y_IS_TMC2130
-  //#define Y2_IS_TMC2130
-  //#define Z_IS_TMC2130
-  //#define Z2_IS_TMC2130
-  //#define E0_IS_TMC2130
-  //#define E1_IS_TMC2130
-  //#define E2_IS_TMC2130
-  //#define E3_IS_TMC2130
-  //#define E4_IS_TMC2130
-#endif
-
-/**
- * Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
- * Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
+ *
+ * The TMC2130Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2130Stepper
+ *
+ * To use TMC2208 stepper UART-configurable stepper drivers
+ * connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
 * To use the reading capabilities, also connect #_SERIAL_RX_PIN
 * to PDN_UART without a resistor.
 * The drivers can also be used with hardware serial.
 *
- * You'll also need the TMC2208Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2208Stepper).
+ * The TMC2208Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2208Stepper
 */
-//#define HAVE_TMC2208
-#if ENABLED(HAVE_TMC2208)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2208
-  //#define X2_IS_TMC2208
-  //#define Y_IS_TMC2208
-  //#define Y2_IS_TMC2208
-  //#define Z_IS_TMC2208
-  //#define Z2_IS_TMC2208
-  //#define E0_IS_TMC2208
-  //#define E1_IS_TMC2208
-  //#define E2_IS_TMC2208
-  //#define E3_IS_TMC2208
-  //#define E4_IS_TMC2208
-#endif
-
-#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
+#if HAS_TRINAMIC

  #define R_SENSE           0.11  // R_sense resistor for SilentStepStick2130
  #define HOLD_MULTIPLIER    0.5  // Scales down the holding current from run current
@ -1310,25 +1272,12 @@
 // @section L6470

 /**
- * Enable this section if you have L6470 motor drivers.
- * You need to import the L6470 library into the Arduino IDE for this.
- * (https://github.com/ameyer/Arduino-L6470)
+ * L6470 Stepper Driver options
+ *
+ * The Arduino-L6470 library is required for this stepper driver.
+ * https://github.com/ameyer/Arduino-L6470
 */
-
-//#define HAVE_L6470DRIVER
-#if ENABLED(HAVE_L6470DRIVER)
-
-  //#define X_IS_L6470
-  //#define X2_IS_L6470
-  //#define Y_IS_L6470
-  //#define Y2_IS_L6470
-  //#define Z_IS_L6470
-  //#define Z2_IS_L6470
-  //#define E0_IS_L6470
-  //#define E1_IS_L6470
-  //#define E2_IS_L6470
-  //#define E3_IS_L6470
-  //#define E4_IS_L6470
+#if HAS_DRIVER(L6470)

  #define X_MICROSTEPS      16 // number of microsteps
  #define X_OVERCURRENT   2000 // maxc current in mA. If the current goes over this value, the driver will switch off
@ -1374,7 +1323,7 @@
  #define E4_OVERCURRENT  2000
  #define E4_STALLCURRENT 1500

-#endif
+#endif // L6470

 /**
 * TWI/I2C BUS
--- a/Marlin/src/config/examples/delta/generic/Configuration_adv.h
+++ b/Marlin/src/config/examples/delta/generic/Configuration_adv.h
@ -839,15 +839,17 @@

 /**
 * Minimum delay after setting the stepper DIR (in ns)
- *    0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
- *   20 : Minimum for TMC2xxx drivers
- *  200 : Minimum for A4988 drivers
- *  500 : Minimum for LV8729 drivers (guess, no info in datasheet)
- *  650 : Minimum for DRV8825 drivers
- * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
- *15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *     0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
+ *    20 : Minimum for TMC2xxx drivers
+ *   200 : Minimum for A4988 drivers
+ *   500 : Minimum for LV8729 drivers (guess, no info in datasheet)
+ *   650 : Minimum for DRV8825 drivers
+ *  1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
+ * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_DIR_DELAY 0
+//#define MINIMUM_STEPPER_DIR_DELAY 650

 /**
 * Minimum stepper driver pulse width (in µs)
@ -857,8 +859,10 @@
 *   2 : Minimum for DRV8825 stepper drivers
 *   3 : Minimum for TB6600 stepper drivers
 *  30 : Minimum for TB6560 stepper drivers
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_PULSE 2
+//#define MINIMUM_STEPPER_PULSE 2

 /**
 * Maximum stepping rate (in Hz) the stepper driver allows
@ -869,8 +873,10 @@
 *  150000 : Maximum for TB6600 stepper driver
 *  130000 : Maximum for LV8729 stepper driver
 *   15000 : Maximum for TB6560 stepper driver
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MAXIMUM_STEPPER_RATE 250000
+//#define MAXIMUM_STEPPER_RATE 250000

 // @section temperature

@ -1038,23 +1044,12 @@
 // @section tmc

 /**
- * Enable this section if you have TMC26X motor drivers.
- * You will need to import the TMC26XStepper library into the Arduino IDE for this
- * (https://github.com/trinamic/TMC26XStepper.git)
+ * TMC26X Stepper Driver options
+ *
+ * The TMC26XStepper library is required for this stepper driver.
+ * https://github.com/trinamic/TMC26XStepper
 */
-//#define HAVE_TMC26X
-#if ENABLED(HAVE_TMC26X)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC26X
-  //#define X2_IS_TMC26X
-  //#define Y_IS_TMC26X
-  //#define Y2_IS_TMC26X
-  //#define Z_IS_TMC26X
-  //#define Z2_IS_TMC26X
-  //#define E0_IS_TMC26X
-  //#define E1_IS_TMC26X
-  //#define E2_IS_TMC26X
-  //#define E3_IS_TMC26X
-  //#define E4_IS_TMC26X
+#if HAS_DRIVER(TMC26X)

  #define X_MAX_CURRENT     1000 // in mA
  #define X_SENSE_RESISTOR    91 // in mOhms
@ -1100,62 +1095,29 @@
  #define E4_SENSE_RESISTOR   91
  #define E4_MICROSTEPS       16

-#endif
+#endif // TMC26X

 // @section tmc_smart

 /**
- * Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
- *
- * You'll also need the TMC2130Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2130Stepper).
- *
 * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
 * the hardware SPI interface on your board and define the required CS pins
 * in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
 * You may also use software SPI if you wish to use general purpose IO pins.
- */
-//#define HAVE_TMC2130
-#if ENABLED(HAVE_TMC2130)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2130
-  //#define X2_IS_TMC2130
-  //#define Y_IS_TMC2130
-  //#define Y2_IS_TMC2130
-  //#define Z_IS_TMC2130
-  //#define Z2_IS_TMC2130
-  //#define E0_IS_TMC2130
-  //#define E1_IS_TMC2130
-  //#define E2_IS_TMC2130
-  //#define E3_IS_TMC2130
-  //#define E4_IS_TMC2130
-#endif
-
-/**
- * Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
- * Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
+ *
+ * The TMC2130Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2130Stepper
+ *
+ * To use TMC2208 stepper UART-configurable stepper drivers
+ * connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
 * To use the reading capabilities, also connect #_SERIAL_RX_PIN
 * to PDN_UART without a resistor.
 * The drivers can also be used with hardware serial.
 *
- * You'll also need the TMC2208Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2208Stepper).
+ * The TMC2208Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2208Stepper
 */
-//#define HAVE_TMC2208
-#if ENABLED(HAVE_TMC2208)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2208
-  //#define X2_IS_TMC2208
-  //#define Y_IS_TMC2208
-  //#define Y2_IS_TMC2208
-  //#define Z_IS_TMC2208
-  //#define Z2_IS_TMC2208
-  //#define E0_IS_TMC2208
-  //#define E1_IS_TMC2208
-  //#define E2_IS_TMC2208
-  //#define E3_IS_TMC2208
-  //#define E4_IS_TMC2208
-#endif
-
-#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
+#if HAS_TRINAMIC

  #define R_SENSE           0.11  // R_sense resistor for SilentStepStick2130
  #define HOLD_MULTIPLIER    0.5  // Scales down the holding current from run current
@ -1310,25 +1272,12 @@
 // @section L6470

 /**
- * Enable this section if you have L6470 motor drivers.
- * You need to import the L6470 library into the Arduino IDE for this.
- * (https://github.com/ameyer/Arduino-L6470)
+ * L6470 Stepper Driver options
+ *
+ * The Arduino-L6470 library is required for this stepper driver.
+ * https://github.com/ameyer/Arduino-L6470
 */
-
-//#define HAVE_L6470DRIVER
-#if ENABLED(HAVE_L6470DRIVER)
-
-  //#define X_IS_L6470
-  //#define X2_IS_L6470
-  //#define Y_IS_L6470
-  //#define Y2_IS_L6470
-  //#define Z_IS_L6470
-  //#define Z2_IS_L6470
-  //#define E0_IS_L6470
-  //#define E1_IS_L6470
-  //#define E2_IS_L6470
-  //#define E3_IS_L6470
-  //#define E4_IS_L6470
+#if HAS_DRIVER(L6470)

  #define X_MICROSTEPS      16 // number of microsteps
  #define X_OVERCURRENT   2000 // maxc current in mA. If the current goes over this value, the driver will switch off
@ -1374,7 +1323,7 @@
  #define E4_OVERCURRENT  2000
  #define E4_STALLCURRENT 1500

-#endif
+#endif // L6470

 /**
 * TWI/I2C BUS
--- a/Marlin/src/config/examples/delta/kossel_mini/Configuration.h
+++ b/Marlin/src/config/examples/delta/kossel_mini/Configuration.h
@ -617,6 +617,29 @@
 #define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
 #define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.

+/**
+ * Specify Stepper Driver types
+ * The options are used to determine driver pulse timings as well as more advanced functionality.
+ * Stepper timing options can be overridden in Configuration_adv.h
+ *
+ * Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
+ *          TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
+ *          TMC26X,  TMC26X_STANDALONE,  TMC2660, TMC2660_STANDALONE,
+ *          TMC5130, TMC5130_STANDALONE
+ * :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
+ */
+#define X_DRIVER_TYPE  A4988
+#define Y_DRIVER_TYPE  A4988
+#define Z_DRIVER_TYPE  A4988
+#define X2_DRIVER_TYPE A4988
+#define Y2_DRIVER_TYPE A4988
+#define Z2_DRIVER_TYPE A4988
+#define E0_DRIVER_TYPE A4988
+#define E1_DRIVER_TYPE A4988
+#define E2_DRIVER_TYPE A4988
+#define E3_DRIVER_TYPE A4988
+#define E4_DRIVER_TYPE A4988
+
 // Enable this feature if all enabled endstop pins are interrupt-capable.
 // This will remove the need to poll the interrupt pins, saving many CPU cycles.
 //#define ENDSTOP_INTERRUPTS_FEATURE
--- a/Marlin/src/config/examples/delta/kossel_mini/Configuration_adv.h
+++ b/Marlin/src/config/examples/delta/kossel_mini/Configuration_adv.h
@ -839,15 +839,17 @@

 /**
 * Minimum delay after setting the stepper DIR (in ns)
- *    0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
- *   20 : Minimum for TMC2xxx drivers
- *  200 : Minimum for A4988 drivers
- *  500 : Minimum for LV8729 drivers (guess, no info in datasheet)
- *  650 : Minimum for DRV8825 drivers
- * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
- *15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *     0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
+ *    20 : Minimum for TMC2xxx drivers
+ *   200 : Minimum for A4988 drivers
+ *   500 : Minimum for LV8729 drivers (guess, no info in datasheet)
+ *   650 : Minimum for DRV8825 drivers
+ *  1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
+ * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_DIR_DELAY 0
+//#define MINIMUM_STEPPER_DIR_DELAY 650

 /**
 * Minimum stepper driver pulse width (in µs)
@ -857,8 +859,10 @@
 *   2 : Minimum for DRV8825 stepper drivers
 *   3 : Minimum for TB6600 stepper drivers
 *  30 : Minimum for TB6560 stepper drivers
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_PULSE 2
+//#define MINIMUM_STEPPER_PULSE 2

 /**
 * Maximum stepping rate (in Hz) the stepper driver allows
@ -869,8 +873,10 @@
 *  150000 : Maximum for TB6600 stepper driver
 *  130000 : Maximum for LV8729 stepper driver
 *   15000 : Maximum for TB6560 stepper driver
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MAXIMUM_STEPPER_RATE 250000
+//#define MAXIMUM_STEPPER_RATE 250000

 // @section temperature

@ -1038,23 +1044,12 @@
 // @section tmc

 /**
- * Enable this section if you have TMC26X motor drivers.
- * You will need to import the TMC26XStepper library into the Arduino IDE for this
- * (https://github.com/trinamic/TMC26XStepper.git)
+ * TMC26X Stepper Driver options
+ *
+ * The TMC26XStepper library is required for this stepper driver.
+ * https://github.com/trinamic/TMC26XStepper
 */
-//#define HAVE_TMC26X
-#if ENABLED(HAVE_TMC26X)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC26X
-  //#define X2_IS_TMC26X
-  //#define Y_IS_TMC26X
-  //#define Y2_IS_TMC26X
-  //#define Z_IS_TMC26X
-  //#define Z2_IS_TMC26X
-  //#define E0_IS_TMC26X
-  //#define E1_IS_TMC26X
-  //#define E2_IS_TMC26X
-  //#define E3_IS_TMC26X
-  //#define E4_IS_TMC26X
+#if HAS_DRIVER(TMC26X)

  #define X_MAX_CURRENT     1000 // in mA
  #define X_SENSE_RESISTOR    91 // in mOhms
@ -1100,62 +1095,29 @@
  #define E4_SENSE_RESISTOR   91
  #define E4_MICROSTEPS       16

-#endif
+#endif // TMC26X

 // @section tmc_smart

 /**
- * Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
- *
- * You'll also need the TMC2130Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2130Stepper).
- *
 * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
 * the hardware SPI interface on your board and define the required CS pins
 * in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
 * You may also use software SPI if you wish to use general purpose IO pins.
- */
-//#define HAVE_TMC2130
-#if ENABLED(HAVE_TMC2130)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2130
-  //#define X2_IS_TMC2130
-  //#define Y_IS_TMC2130
-  //#define Y2_IS_TMC2130
-  //#define Z_IS_TMC2130
-  //#define Z2_IS_TMC2130
-  //#define E0_IS_TMC2130
-  //#define E1_IS_TMC2130
-  //#define E2_IS_TMC2130
-  //#define E3_IS_TMC2130
-  //#define E4_IS_TMC2130
-#endif
-
-/**
- * Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
- * Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
+ *
+ * The TMC2130Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2130Stepper
+ *
+ * To use TMC2208 stepper UART-configurable stepper drivers
+ * connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
 * To use the reading capabilities, also connect #_SERIAL_RX_PIN
 * to PDN_UART without a resistor.
 * The drivers can also be used with hardware serial.
 *
- * You'll also need the TMC2208Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2208Stepper).
+ * The TMC2208Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2208Stepper
 */
-//#define HAVE_TMC2208
-#if ENABLED(HAVE_TMC2208)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2208
-  //#define X2_IS_TMC2208
-  //#define Y_IS_TMC2208
-  //#define Y2_IS_TMC2208
-  //#define Z_IS_TMC2208
-  //#define Z2_IS_TMC2208
-  //#define E0_IS_TMC2208
-  //#define E1_IS_TMC2208
-  //#define E2_IS_TMC2208
-  //#define E3_IS_TMC2208
-  //#define E4_IS_TMC2208
-#endif
-
-#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
+#if HAS_TRINAMIC

  #define R_SENSE           0.11  // R_sense resistor for SilentStepStick2130
  #define HOLD_MULTIPLIER    0.5  // Scales down the holding current from run current
@ -1310,25 +1272,12 @@
 // @section L6470

 /**
- * Enable this section if you have L6470 motor drivers.
- * You need to import the L6470 library into the Arduino IDE for this.
- * (https://github.com/ameyer/Arduino-L6470)
+ * L6470 Stepper Driver options
+ *
+ * The Arduino-L6470 library is required for this stepper driver.
+ * https://github.com/ameyer/Arduino-L6470
 */
-
-//#define HAVE_L6470DRIVER
-#if ENABLED(HAVE_L6470DRIVER)
-
-  //#define X_IS_L6470
-  //#define X2_IS_L6470
-  //#define Y_IS_L6470
-  //#define Y2_IS_L6470
-  //#define Z_IS_L6470
-  //#define Z2_IS_L6470
-  //#define E0_IS_L6470
-  //#define E1_IS_L6470
-  //#define E2_IS_L6470
-  //#define E3_IS_L6470
-  //#define E4_IS_L6470
+#if HAS_DRIVER(L6470)

  #define X_MICROSTEPS      16 // number of microsteps
  #define X_OVERCURRENT   2000 // maxc current in mA. If the current goes over this value, the driver will switch off
@ -1374,7 +1323,7 @@
  #define E4_OVERCURRENT  2000
  #define E4_STALLCURRENT 1500

-#endif
+#endif // L6470

 /**
 * TWI/I2C BUS
--- a/Marlin/src/config/examples/delta/kossel_pro/Configuration.h
+++ b/Marlin/src/config/examples/delta/kossel_pro/Configuration.h
@ -603,6 +603,29 @@
 #define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
 #define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.

+/**
+ * Specify Stepper Driver types
+ * The options are used to determine driver pulse timings as well as more advanced functionality.
+ * Stepper timing options can be overridden in Configuration_adv.h
+ *
+ * Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
+ *          TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
+ *          TMC26X,  TMC26X_STANDALONE,  TMC2660, TMC2660_STANDALONE,
+ *          TMC5130, TMC5130_STANDALONE
+ * :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
+ */
+#define X_DRIVER_TYPE  A4988
+#define Y_DRIVER_TYPE  A4988
+#define Z_DRIVER_TYPE  A4988
+#define X2_DRIVER_TYPE A4988
+#define Y2_DRIVER_TYPE A4988
+#define Z2_DRIVER_TYPE A4988
+#define E0_DRIVER_TYPE A4988
+#define E1_DRIVER_TYPE A4988
+#define E2_DRIVER_TYPE A4988
+#define E3_DRIVER_TYPE A4988
+#define E4_DRIVER_TYPE A4988
+
 // Enable this feature if all enabled endstop pins are interrupt-capable.
 // This will remove the need to poll the interrupt pins, saving many CPU cycles.
 //#define ENDSTOP_INTERRUPTS_FEATURE
--- a/Marlin/src/config/examples/delta/kossel_pro/Configuration_adv.h
+++ b/Marlin/src/config/examples/delta/kossel_pro/Configuration_adv.h
@ -844,15 +844,17 @@

 /**
 * Minimum delay after setting the stepper DIR (in ns)
- *    0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
- *   20 : Minimum for TMC2xxx drivers
- *  200 : Minimum for A4988 drivers
- *  500 : Minimum for LV8729 drivers (guess, no info in datasheet)
- *  650 : Minimum for DRV8825 drivers
- * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
- *15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *     0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
+ *    20 : Minimum for TMC2xxx drivers
+ *   200 : Minimum for A4988 drivers
+ *   500 : Minimum for LV8729 drivers (guess, no info in datasheet)
+ *   650 : Minimum for DRV8825 drivers
+ *  1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
+ * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_DIR_DELAY 0
+//#define MINIMUM_STEPPER_DIR_DELAY 650

 /**
 * Minimum stepper driver pulse width (in µs)
@ -862,8 +864,10 @@
 *   2 : Minimum for DRV8825 stepper drivers
 *   3 : Minimum for TB6600 stepper drivers
 *  30 : Minimum for TB6560 stepper drivers
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_PULSE 2
+//#define MINIMUM_STEPPER_PULSE 2

 /**
 * Maximum stepping rate (in Hz) the stepper driver allows
@ -874,8 +878,10 @@
 *  150000 : Maximum for TB6600 stepper driver
 *  130000 : Maximum for LV8729 stepper driver
 *   15000 : Maximum for TB6560 stepper driver
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MAXIMUM_STEPPER_RATE 250000
+//#define MAXIMUM_STEPPER_RATE 250000

 // @section temperature

@ -1043,23 +1049,12 @@
 // @section tmc

 /**
- * Enable this section if you have TMC26X motor drivers.
- * You will need to import the TMC26XStepper library into the Arduino IDE for this
- * (https://github.com/trinamic/TMC26XStepper.git)
+ * TMC26X Stepper Driver options
+ *
+ * The TMC26XStepper library is required for this stepper driver.
+ * https://github.com/trinamic/TMC26XStepper
 */
-//#define HAVE_TMC26X
-#if ENABLED(HAVE_TMC26X)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC26X
-  //#define X2_IS_TMC26X
-  //#define Y_IS_TMC26X
-  //#define Y2_IS_TMC26X
-  //#define Z_IS_TMC26X
-  //#define Z2_IS_TMC26X
-  //#define E0_IS_TMC26X
-  //#define E1_IS_TMC26X
-  //#define E2_IS_TMC26X
-  //#define E3_IS_TMC26X
-  //#define E4_IS_TMC26X
+#if HAS_DRIVER(TMC26X)

  #define X_MAX_CURRENT     1000 // in mA
  #define X_SENSE_RESISTOR    91 // in mOhms
@ -1105,62 +1100,29 @@
  #define E4_SENSE_RESISTOR   91
  #define E4_MICROSTEPS       16

-#endif
+#endif // TMC26X

 // @section tmc_smart

 /**
- * Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
- *
- * You'll also need the TMC2130Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2130Stepper).
- *
 * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
 * the hardware SPI interface on your board and define the required CS pins
 * in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
 * You may also use software SPI if you wish to use general purpose IO pins.
- */
-//#define HAVE_TMC2130
-#if ENABLED(HAVE_TMC2130)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2130
-  //#define X2_IS_TMC2130
-  //#define Y_IS_TMC2130
-  //#define Y2_IS_TMC2130
-  //#define Z_IS_TMC2130
-  //#define Z2_IS_TMC2130
-  //#define E0_IS_TMC2130
-  //#define E1_IS_TMC2130
-  //#define E2_IS_TMC2130
-  //#define E3_IS_TMC2130
-  //#define E4_IS_TMC2130
-#endif
-
-/**
- * Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
- * Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
+ *
+ * The TMC2130Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2130Stepper
+ *
+ * To use TMC2208 stepper UART-configurable stepper drivers
+ * connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
 * To use the reading capabilities, also connect #_SERIAL_RX_PIN
 * to PDN_UART without a resistor.
 * The drivers can also be used with hardware serial.
 *
- * You'll also need the TMC2208Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2208Stepper).
+ * The TMC2208Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2208Stepper
 */
-//#define HAVE_TMC2208
-#if ENABLED(HAVE_TMC2208)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2208
-  //#define X2_IS_TMC2208
-  //#define Y_IS_TMC2208
-  //#define Y2_IS_TMC2208
-  //#define Z_IS_TMC2208
-  //#define Z2_IS_TMC2208
-  //#define E0_IS_TMC2208
-  //#define E1_IS_TMC2208
-  //#define E2_IS_TMC2208
-  //#define E3_IS_TMC2208
-  //#define E4_IS_TMC2208
-#endif
-
-#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
+#if HAS_TRINAMIC

  #define R_SENSE           0.11  // R_sense resistor for SilentStepStick2130
  #define HOLD_MULTIPLIER    0.5  // Scales down the holding current from run current
@ -1315,25 +1277,12 @@
 // @section L6470

 /**
- * Enable this section if you have L6470 motor drivers.
- * You need to import the L6470 library into the Arduino IDE for this.
- * (https://github.com/ameyer/Arduino-L6470)
+ * L6470 Stepper Driver options
+ *
+ * The Arduino-L6470 library is required for this stepper driver.
+ * https://github.com/ameyer/Arduino-L6470
 */
-
-//#define HAVE_L6470DRIVER
-#if ENABLED(HAVE_L6470DRIVER)
-
-  //#define X_IS_L6470
-  //#define X2_IS_L6470
-  //#define Y_IS_L6470
-  //#define Y2_IS_L6470
-  //#define Z_IS_L6470
-  //#define Z2_IS_L6470
-  //#define E0_IS_L6470
-  //#define E1_IS_L6470
-  //#define E2_IS_L6470
-  //#define E3_IS_L6470
-  //#define E4_IS_L6470
+#if HAS_DRIVER(L6470)

  #define X_MICROSTEPS      16 // number of microsteps
  #define X_OVERCURRENT   2000 // maxc current in mA. If the current goes over this value, the driver will switch off
@ -1379,7 +1328,7 @@
  #define E4_OVERCURRENT  2000
  #define E4_STALLCURRENT 1500

-#endif
+#endif // L6470

 /**
 * TWI/I2C BUS
--- a/Marlin/src/config/examples/delta/kossel_xl/Configuration.h
+++ b/Marlin/src/config/examples/delta/kossel_xl/Configuration.h
@ -621,6 +621,29 @@
 #define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
 #define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.

+/**
+ * Specify Stepper Driver types
+ * The options are used to determine driver pulse timings as well as more advanced functionality.
+ * Stepper timing options can be overridden in Configuration_adv.h
+ *
+ * Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
+ *          TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
+ *          TMC26X,  TMC26X_STANDALONE,  TMC2660, TMC2660_STANDALONE,
+ *          TMC5130, TMC5130_STANDALONE
+ * :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
+ */
+#define X_DRIVER_TYPE  A4988
+#define Y_DRIVER_TYPE  A4988
+#define Z_DRIVER_TYPE  A4988
+#define X2_DRIVER_TYPE A4988
+#define Y2_DRIVER_TYPE A4988
+#define Z2_DRIVER_TYPE A4988
+#define E0_DRIVER_TYPE A4988
+#define E1_DRIVER_TYPE A4988
+#define E2_DRIVER_TYPE A4988
+#define E3_DRIVER_TYPE A4988
+#define E4_DRIVER_TYPE A4988
+
 // Enable this feature if all enabled endstop pins are interrupt-capable.
 // This will remove the need to poll the interrupt pins, saving many CPU cycles.
 //#define ENDSTOP_INTERRUPTS_FEATURE
--- a/Marlin/src/config/examples/delta/kossel_xl/Configuration_adv.h
+++ b/Marlin/src/config/examples/delta/kossel_xl/Configuration_adv.h
@ -839,15 +839,17 @@

 /**
 * Minimum delay after setting the stepper DIR (in ns)
- *    0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
- *   20 : Minimum for TMC2xxx drivers
- *  200 : Minimum for A4988 drivers
- *  500 : Minimum for LV8729 drivers (guess, no info in datasheet)
- *  650 : Minimum for DRV8825 drivers
- * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
- *15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *     0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
+ *    20 : Minimum for TMC2xxx drivers
+ *   200 : Minimum for A4988 drivers
+ *   500 : Minimum for LV8729 drivers (guess, no info in datasheet)
+ *   650 : Minimum for DRV8825 drivers
+ *  1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
+ * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_DIR_DELAY 0
+//#define MINIMUM_STEPPER_DIR_DELAY 650

 /**
 * Minimum stepper driver pulse width (in µs)
@ -857,8 +859,10 @@
 *   2 : Minimum for DRV8825 stepper drivers
 *   3 : Minimum for TB6600 stepper drivers
 *  30 : Minimum for TB6560 stepper drivers
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_PULSE 2
+//#define MINIMUM_STEPPER_PULSE 2

 /**
 * Maximum stepping rate (in Hz) the stepper driver allows
@ -869,8 +873,10 @@
 *  150000 : Maximum for TB6600 stepper driver
 *  130000 : Maximum for LV8729 stepper driver
 *   15000 : Maximum for TB6560 stepper driver
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MAXIMUM_STEPPER_RATE 250000
+//#define MAXIMUM_STEPPER_RATE 250000

 // @section temperature

@ -1038,23 +1044,12 @@
 // @section tmc

 /**
- * Enable this section if you have TMC26X motor drivers.
- * You will need to import the TMC26XStepper library into the Arduino IDE for this
- * (https://github.com/trinamic/TMC26XStepper.git)
+ * TMC26X Stepper Driver options
+ *
+ * The TMC26XStepper library is required for this stepper driver.
+ * https://github.com/trinamic/TMC26XStepper
 */
-//#define HAVE_TMC26X
-#if ENABLED(HAVE_TMC26X)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC26X
-  //#define X2_IS_TMC26X
-  //#define Y_IS_TMC26X
-  //#define Y2_IS_TMC26X
-  //#define Z_IS_TMC26X
-  //#define Z2_IS_TMC26X
-  //#define E0_IS_TMC26X
-  //#define E1_IS_TMC26X
-  //#define E2_IS_TMC26X
-  //#define E3_IS_TMC26X
-  //#define E4_IS_TMC26X
+#if HAS_DRIVER(TMC26X)

  #define X_MAX_CURRENT     1000 // in mA
  #define X_SENSE_RESISTOR    91 // in mOhms
@ -1100,62 +1095,29 @@
  #define E4_SENSE_RESISTOR   91
  #define E4_MICROSTEPS       16

-#endif
+#endif // TMC26X

 // @section tmc_smart

 /**
- * Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
- *
- * You'll also need the TMC2130Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2130Stepper).
- *
 * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
 * the hardware SPI interface on your board and define the required CS pins
 * in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
 * You may also use software SPI if you wish to use general purpose IO pins.
- */
-//#define HAVE_TMC2130
-#if ENABLED(HAVE_TMC2130)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2130
-  //#define X2_IS_TMC2130
-  //#define Y_IS_TMC2130
-  //#define Y2_IS_TMC2130
-  //#define Z_IS_TMC2130
-  //#define Z2_IS_TMC2130
-  //#define E0_IS_TMC2130
-  //#define E1_IS_TMC2130
-  //#define E2_IS_TMC2130
-  //#define E3_IS_TMC2130
-  //#define E4_IS_TMC2130
-#endif
-
-/**
- * Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
- * Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
+ *
+ * The TMC2130Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2130Stepper
+ *
+ * To use TMC2208 stepper UART-configurable stepper drivers
+ * connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
 * To use the reading capabilities, also connect #_SERIAL_RX_PIN
 * to PDN_UART without a resistor.
 * The drivers can also be used with hardware serial.
 *
- * You'll also need the TMC2208Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2208Stepper).
+ * The TMC2208Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2208Stepper
 */
-//#define HAVE_TMC2208
-#if ENABLED(HAVE_TMC2208)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2208
-  //#define X2_IS_TMC2208
-  //#define Y_IS_TMC2208
-  //#define Y2_IS_TMC2208
-  //#define Z_IS_TMC2208
-  //#define Z2_IS_TMC2208
-  //#define E0_IS_TMC2208
-  //#define E1_IS_TMC2208
-  //#define E2_IS_TMC2208
-  //#define E3_IS_TMC2208
-  //#define E4_IS_TMC2208
-#endif
-
-#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
+#if HAS_TRINAMIC

  #define R_SENSE           0.11  // R_sense resistor for SilentStepStick2130
  #define HOLD_MULTIPLIER    0.5  // Scales down the holding current from run current
@ -1310,25 +1272,12 @@
 // @section L6470

 /**
- * Enable this section if you have L6470 motor drivers.
- * You need to import the L6470 library into the Arduino IDE for this.
- * (https://github.com/ameyer/Arduino-L6470)
+ * L6470 Stepper Driver options
+ *
+ * The Arduino-L6470 library is required for this stepper driver.
+ * https://github.com/ameyer/Arduino-L6470
 */
-
-//#define HAVE_L6470DRIVER
-#if ENABLED(HAVE_L6470DRIVER)
-
-  //#define X_IS_L6470
-  //#define X2_IS_L6470
-  //#define Y_IS_L6470
-  //#define Y2_IS_L6470
-  //#define Z_IS_L6470
-  //#define Z2_IS_L6470
-  //#define E0_IS_L6470
-  //#define E1_IS_L6470
-  //#define E2_IS_L6470
-  //#define E3_IS_L6470
-  //#define E4_IS_L6470
+#if HAS_DRIVER(L6470)

  #define X_MICROSTEPS      16 // number of microsteps
  #define X_OVERCURRENT   2000 // maxc current in mA. If the current goes over this value, the driver will switch off
@ -1374,7 +1323,7 @@
  #define E4_OVERCURRENT  2000
  #define E4_STALLCURRENT 1500

-#endif
+#endif // L6470

 /**
 * TWI/I2C BUS
--- a/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration.h
+++ b/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration.h
@ -564,9 +564,32 @@
 #define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
 #define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.

+/**
+ * Specify Stepper Driver types
+ * The options are used to determine driver pulse timings as well as more advanced functionality.
+ * Stepper timing options can be overridden in Configuration_adv.h
+ *
+ * Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
+ *          TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
+ *          TMC26X,  TMC26X_STANDALONE,  TMC2660, TMC2660_STANDALONE,
+ *          TMC5130, TMC5130_STANDALONE
+ * :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
+ */
+#define X_DRIVER_TYPE  A4988
+#define Y_DRIVER_TYPE  A4988
+#define Z_DRIVER_TYPE  A4988
+#define X2_DRIVER_TYPE A4988
+#define Y2_DRIVER_TYPE A4988
+#define Z2_DRIVER_TYPE A4988
+#define E0_DRIVER_TYPE A4988
+#define E1_DRIVER_TYPE A4988
+#define E2_DRIVER_TYPE A4988
+#define E3_DRIVER_TYPE A4988
+#define E4_DRIVER_TYPE A4988
+
 // Enable this feature if all enabled endstop pins are interrupt-capable.
 // This will remove the need to poll the interrupt pins, saving many CPU cycles.
-#define ENDSTOP_INTERRUPTS_FEATURE
+//#define ENDSTOP_INTERRUPTS_FEATURE

 /**
 * Endstop Noise Filter
--- a/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration_adv.h
+++ b/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration_adv.h
@ -837,15 +837,17 @@

 /**
 * Minimum delay after setting the stepper DIR (in ns)
- *    0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
- *   20 : Minimum for TMC2xxx drivers
- *  200 : Minimum for A4988 drivers
- *  500 : Minimum for LV8729 drivers (guess, no info in datasheet)
- *  650 : Minimum for DRV8825 drivers
- * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
- *15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *     0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
+ *    20 : Minimum for TMC2xxx drivers
+ *   200 : Minimum for A4988 drivers
+ *   500 : Minimum for LV8729 drivers (guess, no info in datasheet)
+ *   650 : Minimum for DRV8825 drivers
+ *  1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
+ * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_DIR_DELAY 0
+//#define MINIMUM_STEPPER_DIR_DELAY 650

 /**
 * Minimum stepper driver pulse width (in µs)
@ -855,8 +857,10 @@
 *   2 : Minimum for DRV8825 stepper drivers
 *   3 : Minimum for TB6600 stepper drivers
 *  30 : Minimum for TB6560 stepper drivers
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_PULSE 2
+//#define MINIMUM_STEPPER_PULSE 2

 /**
 * Maximum stepping rate (in Hz) the stepper driver allows
@ -867,8 +871,10 @@
 *  150000 : Maximum for TB6600 stepper driver
 *  130000 : Maximum for LV8729 stepper driver
 *   15000 : Maximum for TB6560 stepper driver
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MAXIMUM_STEPPER_RATE 250000
+//#define MAXIMUM_STEPPER_RATE 250000

 // @section temperature

@ -1036,23 +1042,12 @@
 // @section tmc

 /**
- * Enable this section if you have TMC26X motor drivers.
- * You will need to import the TMC26XStepper library into the Arduino IDE for this
- * (https://github.com/trinamic/TMC26XStepper.git)
+ * TMC26X Stepper Driver options
+ *
+ * The TMC26XStepper library is required for this stepper driver.
+ * https://github.com/trinamic/TMC26XStepper
 */
-//#define HAVE_TMC26X
-#if ENABLED(HAVE_TMC26X)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC26X
-  //#define X2_IS_TMC26X
-  //#define Y_IS_TMC26X
-  //#define Y2_IS_TMC26X
-  //#define Z_IS_TMC26X
-  //#define Z2_IS_TMC26X
-  //#define E0_IS_TMC26X
-  //#define E1_IS_TMC26X
-  //#define E2_IS_TMC26X
-  //#define E3_IS_TMC26X
-  //#define E4_IS_TMC26X
+#if HAS_DRIVER(TMC26X)

  #define X_MAX_CURRENT     1000 // in mA
  #define X_SENSE_RESISTOR    91 // in mOhms
@ -1098,62 +1093,29 @@
  #define E4_SENSE_RESISTOR   91
  #define E4_MICROSTEPS       16

-#endif
+#endif // TMC26X

 // @section tmc_smart

 /**
- * Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
- *
- * You'll also need the TMC2130Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2130Stepper).
- *
 * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
 * the hardware SPI interface on your board and define the required CS pins
 * in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
 * You may also use software SPI if you wish to use general purpose IO pins.
- */
-//#define HAVE_TMC2130
-#if ENABLED(HAVE_TMC2130)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2130
-  //#define X2_IS_TMC2130
-  //#define Y_IS_TMC2130
-  //#define Y2_IS_TMC2130
-  //#define Z_IS_TMC2130
-  //#define Z2_IS_TMC2130
-  //#define E0_IS_TMC2130
-  //#define E1_IS_TMC2130
-  //#define E2_IS_TMC2130
-  //#define E3_IS_TMC2130
-  //#define E4_IS_TMC2130
-#endif
-
-/**
- * Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
- * Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
+ *
+ * The TMC2130Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2130Stepper
+ *
+ * To use TMC2208 stepper UART-configurable stepper drivers
+ * connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
 * To use the reading capabilities, also connect #_SERIAL_RX_PIN
 * to PDN_UART without a resistor.
 * The drivers can also be used with hardware serial.
 *
- * You'll also need the TMC2208Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2208Stepper).
+ * The TMC2208Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2208Stepper
 */
-//#define HAVE_TMC2208
-#if ENABLED(HAVE_TMC2208)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2208
-  //#define X2_IS_TMC2208
-  //#define Y_IS_TMC2208
-  //#define Y2_IS_TMC2208
-  //#define Z_IS_TMC2208
-  //#define Z2_IS_TMC2208
-  //#define E0_IS_TMC2208
-  //#define E1_IS_TMC2208
-  //#define E2_IS_TMC2208
-  //#define E3_IS_TMC2208
-  //#define E4_IS_TMC2208
-#endif
-
-#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
+#if HAS_TRINAMIC

  #define R_SENSE           0.11  // R_sense resistor for SilentStepStick2130
  #define HOLD_MULTIPLIER    0.5  // Scales down the holding current from run current
@ -1308,25 +1270,12 @@
 // @section L6470

 /**
- * Enable this section if you have L6470 motor drivers.
- * You need to import the L6470 library into the Arduino IDE for this.
- * (https://github.com/ameyer/Arduino-L6470)
+ * L6470 Stepper Driver options
+ *
+ * The Arduino-L6470 library is required for this stepper driver.
+ * https://github.com/ameyer/Arduino-L6470
 */
-
-//#define HAVE_L6470DRIVER
-#if ENABLED(HAVE_L6470DRIVER)
-
-  //#define X_IS_L6470
-  //#define X2_IS_L6470
-  //#define Y_IS_L6470
-  //#define Y2_IS_L6470
-  //#define Z_IS_L6470
-  //#define Z2_IS_L6470
-  //#define E0_IS_L6470
-  //#define E1_IS_L6470
-  //#define E2_IS_L6470
-  //#define E3_IS_L6470
-  //#define E4_IS_L6470
+#if HAS_DRIVER(L6470)

  #define X_MICROSTEPS      16 // number of microsteps
  #define X_OVERCURRENT   2000 // maxc current in mA. If the current goes over this value, the driver will switch off
@ -1372,7 +1321,7 @@
  #define E4_OVERCURRENT  2000
  #define E4_STALLCURRENT 1500

-#endif
+#endif // L6470

 /**
 * TWI/I2C BUS
--- a/Marlin/src/config/examples/makibox/Configuration.h
+++ b/Marlin/src/config/examples/makibox/Configuration.h
@ -554,6 +554,29 @@
 #define Z_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
 #define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.

+/**
+ * Specify Stepper Driver types
+ * The options are used to determine driver pulse timings as well as more advanced functionality.
+ * Stepper timing options can be overridden in Configuration_adv.h
+ *
+ * Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
+ *          TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
+ *          TMC26X,  TMC26X_STANDALONE,  TMC2660, TMC2660_STANDALONE,
+ *          TMC5130, TMC5130_STANDALONE
+ * :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
+ */
+#define X_DRIVER_TYPE  A4988
+#define Y_DRIVER_TYPE  A4988
+#define Z_DRIVER_TYPE  A4988
+#define X2_DRIVER_TYPE A4988
+#define Y2_DRIVER_TYPE A4988
+#define Z2_DRIVER_TYPE A4988
+#define E0_DRIVER_TYPE A4988
+#define E1_DRIVER_TYPE A4988
+#define E2_DRIVER_TYPE A4988
+#define E3_DRIVER_TYPE A4988
+#define E4_DRIVER_TYPE A4988
+
 // Enable this feature if all enabled endstop pins are interrupt-capable.
 // This will remove the need to poll the interrupt pins, saving many CPU cycles.
 //#define ENDSTOP_INTERRUPTS_FEATURE
--- a/Marlin/src/config/examples/makibox/Configuration_adv.h
+++ b/Marlin/src/config/examples/makibox/Configuration_adv.h
@ -837,15 +837,17 @@

 /**
 * Minimum delay after setting the stepper DIR (in ns)
- *    0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
- *   20 : Minimum for TMC2xxx drivers
- *  200 : Minimum for A4988 drivers
- *  500 : Minimum for LV8729 drivers (guess, no info in datasheet)
- *  650 : Minimum for DRV8825 drivers
- * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
- *15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *     0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
+ *    20 : Minimum for TMC2xxx drivers
+ *   200 : Minimum for A4988 drivers
+ *   500 : Minimum for LV8729 drivers (guess, no info in datasheet)
+ *   650 : Minimum for DRV8825 drivers
+ *  1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
+ * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_DIR_DELAY 0
+//#define MINIMUM_STEPPER_DIR_DELAY 650

 /**
 * Minimum stepper driver pulse width (in µs)
@ -855,8 +857,10 @@
 *   2 : Minimum for DRV8825 stepper drivers
 *   3 : Minimum for TB6600 stepper drivers
 *  30 : Minimum for TB6560 stepper drivers
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_PULSE 2
+//#define MINIMUM_STEPPER_PULSE 2

 /**
 * Maximum stepping rate (in Hz) the stepper driver allows
@ -867,8 +871,10 @@
 *  150000 : Maximum for TB6600 stepper driver
 *  130000 : Maximum for LV8729 stepper driver
 *   15000 : Maximum for TB6560 stepper driver
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MAXIMUM_STEPPER_RATE 250000
+//#define MAXIMUM_STEPPER_RATE 250000

 // @section temperature

@ -1036,23 +1042,12 @@
 // @section tmc

 /**
- * Enable this section if you have TMC26X motor drivers.
- * You will need to import the TMC26XStepper library into the Arduino IDE for this
- * (https://github.com/trinamic/TMC26XStepper.git)
+ * TMC26X Stepper Driver options
+ *
+ * The TMC26XStepper library is required for this stepper driver.
+ * https://github.com/trinamic/TMC26XStepper
 */
-//#define HAVE_TMC26X
-#if ENABLED(HAVE_TMC26X)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC26X
-  //#define X2_IS_TMC26X
-  //#define Y_IS_TMC26X
-  //#define Y2_IS_TMC26X
-  //#define Z_IS_TMC26X
-  //#define Z2_IS_TMC26X
-  //#define E0_IS_TMC26X
-  //#define E1_IS_TMC26X
-  //#define E2_IS_TMC26X
-  //#define E3_IS_TMC26X
-  //#define E4_IS_TMC26X
+#if HAS_DRIVER(TMC26X)

  #define X_MAX_CURRENT     1000 // in mA
  #define X_SENSE_RESISTOR    91 // in mOhms
@ -1098,62 +1093,29 @@
  #define E4_SENSE_RESISTOR   91
  #define E4_MICROSTEPS       16

-#endif
+#endif // TMC26X

 // @section tmc_smart

 /**
- * Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
- *
- * You'll also need the TMC2130Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2130Stepper).
- *
 * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
 * the hardware SPI interface on your board and define the required CS pins
 * in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
 * You may also use software SPI if you wish to use general purpose IO pins.
- */
-//#define HAVE_TMC2130
-#if ENABLED(HAVE_TMC2130)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2130
-  //#define X2_IS_TMC2130
-  //#define Y_IS_TMC2130
-  //#define Y2_IS_TMC2130
-  //#define Z_IS_TMC2130
-  //#define Z2_IS_TMC2130
-  //#define E0_IS_TMC2130
-  //#define E1_IS_TMC2130
-  //#define E2_IS_TMC2130
-  //#define E3_IS_TMC2130
-  //#define E4_IS_TMC2130
-#endif
-
-/**
- * Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
- * Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
+ *
+ * The TMC2130Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2130Stepper
+ *
+ * To use TMC2208 stepper UART-configurable stepper drivers
+ * connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
 * To use the reading capabilities, also connect #_SERIAL_RX_PIN
 * to PDN_UART without a resistor.
 * The drivers can also be used with hardware serial.
 *
- * You'll also need the TMC2208Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2208Stepper).
+ * The TMC2208Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2208Stepper
 */
-//#define HAVE_TMC2208
-#if ENABLED(HAVE_TMC2208)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2208
-  //#define X2_IS_TMC2208
-  //#define Y_IS_TMC2208
-  //#define Y2_IS_TMC2208
-  //#define Z_IS_TMC2208
-  //#define Z2_IS_TMC2208
-  //#define E0_IS_TMC2208
-  //#define E1_IS_TMC2208
-  //#define E2_IS_TMC2208
-  //#define E3_IS_TMC2208
-  //#define E4_IS_TMC2208
-#endif
-
-#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
+#if HAS_TRINAMIC

  #define R_SENSE           0.11  // R_sense resistor for SilentStepStick2130
  #define HOLD_MULTIPLIER    0.5  // Scales down the holding current from run current
@ -1308,25 +1270,12 @@
 // @section L6470

 /**
- * Enable this section if you have L6470 motor drivers.
- * You need to import the L6470 library into the Arduino IDE for this.
- * (https://github.com/ameyer/Arduino-L6470)
+ * L6470 Stepper Driver options
+ *
+ * The Arduino-L6470 library is required for this stepper driver.
+ * https://github.com/ameyer/Arduino-L6470
 */
-
-//#define HAVE_L6470DRIVER
-#if ENABLED(HAVE_L6470DRIVER)
-
-  //#define X_IS_L6470
-  //#define X2_IS_L6470
-  //#define Y_IS_L6470
-  //#define Y2_IS_L6470
-  //#define Z_IS_L6470
-  //#define Z2_IS_L6470
-  //#define E0_IS_L6470
-  //#define E1_IS_L6470
-  //#define E2_IS_L6470
-  //#define E3_IS_L6470
-  //#define E4_IS_L6470
+#if HAS_DRIVER(L6470)

  #define X_MICROSTEPS      16 // number of microsteps
  #define X_OVERCURRENT   2000 // maxc current in mA. If the current goes over this value, the driver will switch off
@ -1372,7 +1321,7 @@
  #define E4_OVERCURRENT  2000
  #define E4_STALLCURRENT 1500

-#endif
+#endif // L6470

 /**
 * TWI/I2C BUS
--- a/Marlin/src/config/examples/stm32f103ret6/Configuration.h
+++ b/Marlin/src/config/examples/stm32f103ret6/Configuration.h
@ -553,6 +553,29 @@
 #define Z_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
 #define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.

+/**
+ * Specify Stepper Driver types
+ * The options are used to determine driver pulse timings as well as more advanced functionality.
+ * Stepper timing options can be overridden in Configuration_adv.h
+ *
+ * Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
+ *          TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
+ *          TMC26X,  TMC26X_STANDALONE,  TMC2660, TMC2660_STANDALONE,
+ *          TMC5130, TMC5130_STANDALONE
+ * :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
+ */
+#define X_DRIVER_TYPE  A4988
+#define Y_DRIVER_TYPE  A4988
+#define Z_DRIVER_TYPE  A4988
+#define X2_DRIVER_TYPE A4988
+#define Y2_DRIVER_TYPE A4988
+#define Z2_DRIVER_TYPE A4988
+#define E0_DRIVER_TYPE A4988
+#define E1_DRIVER_TYPE A4988
+#define E2_DRIVER_TYPE A4988
+#define E3_DRIVER_TYPE A4988
+#define E4_DRIVER_TYPE A4988
+
 // Enable this feature if all enabled endstop pins are interrupt-capable.
 // This will remove the need to poll the interrupt pins, saving many CPU cycles.
 //#define ENDSTOP_INTERRUPTS_FEATURE
--- a/Marlin/src/config/examples/tvrrug/Round2/Configuration_adv.h
+++ b/Marlin/src/config/examples/tvrrug/Round2/Configuration_adv.h
@ -837,15 +837,17 @@

 /**
 * Minimum delay after setting the stepper DIR (in ns)
- *    0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
- *   20 : Minimum for TMC2xxx drivers
- *  200 : Minimum for A4988 drivers
- *  500 : Minimum for LV8729 drivers (guess, no info in datasheet)
- *  650 : Minimum for DRV8825 drivers
- * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
- *15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *     0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
+ *    20 : Minimum for TMC2xxx drivers
+ *   200 : Minimum for A4988 drivers
+ *   500 : Minimum for LV8729 drivers (guess, no info in datasheet)
+ *   650 : Minimum for DRV8825 drivers
+ *  1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
+ * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_DIR_DELAY 0
+//#define MINIMUM_STEPPER_DIR_DELAY 650

 /**
 * Minimum stepper driver pulse width (in µs)
@ -855,8 +857,10 @@
 *   2 : Minimum for DRV8825 stepper drivers
 *   3 : Minimum for TB6600 stepper drivers
 *  30 : Minimum for TB6560 stepper drivers
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_PULSE 30
+//#define MINIMUM_STEPPER_PULSE 2

 /**
 * Maximum stepping rate (in Hz) the stepper driver allows
@ -867,8 +871,10 @@
 *  150000 : Maximum for TB6600 stepper driver
 *  130000 : Maximum for LV8729 stepper driver
 *   15000 : Maximum for TB6560 stepper driver
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MAXIMUM_STEPPER_RATE 15000
+//#define MAXIMUM_STEPPER_RATE 250000

 // @section temperature

@ -1036,23 +1042,12 @@
 // @section tmc

 /**
- * Enable this section if you have TMC26X motor drivers.
- * You will need to import the TMC26XStepper library into the Arduino IDE for this
- * (https://github.com/trinamic/TMC26XStepper.git)
+ * TMC26X Stepper Driver options
+ *
+ * The TMC26XStepper library is required for this stepper driver.
+ * https://github.com/trinamic/TMC26XStepper
 */
-//#define HAVE_TMC26X
-#if ENABLED(HAVE_TMC26X)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC26X
-  //#define X2_IS_TMC26X
-  //#define Y_IS_TMC26X
-  //#define Y2_IS_TMC26X
-  //#define Z_IS_TMC26X
-  //#define Z2_IS_TMC26X
-  //#define E0_IS_TMC26X
-  //#define E1_IS_TMC26X
-  //#define E2_IS_TMC26X
-  //#define E3_IS_TMC26X
-  //#define E4_IS_TMC26X
+#if HAS_DRIVER(TMC26X)

  #define X_MAX_CURRENT     1000 // in mA
  #define X_SENSE_RESISTOR    91 // in mOhms
@ -1098,62 +1093,29 @@
  #define E4_SENSE_RESISTOR   91
  #define E4_MICROSTEPS       16

-#endif
+#endif // TMC26X

 // @section tmc_smart

 /**
- * Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
- *
- * You'll also need the TMC2130Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2130Stepper).
- *
 * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
 * the hardware SPI interface on your board and define the required CS pins
 * in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
 * You may also use software SPI if you wish to use general purpose IO pins.
- */
-//#define HAVE_TMC2130
-#if ENABLED(HAVE_TMC2130)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2130
-  //#define X2_IS_TMC2130
-  //#define Y_IS_TMC2130
-  //#define Y2_IS_TMC2130
-  //#define Z_IS_TMC2130
-  //#define Z2_IS_TMC2130
-  //#define E0_IS_TMC2130
-  //#define E1_IS_TMC2130
-  //#define E2_IS_TMC2130
-  //#define E3_IS_TMC2130
-  //#define E4_IS_TMC2130
-#endif
-
-/**
- * Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
- * Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
+ *
+ * The TMC2130Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2130Stepper
+ *
+ * To use TMC2208 stepper UART-configurable stepper drivers
+ * connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
 * To use the reading capabilities, also connect #_SERIAL_RX_PIN
 * to PDN_UART without a resistor.
 * The drivers can also be used with hardware serial.
 *
- * You'll also need the TMC2208Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2208Stepper).
+ * The TMC2208Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2208Stepper
 */
-//#define HAVE_TMC2208
-#if ENABLED(HAVE_TMC2208)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2208
-  //#define X2_IS_TMC2208
-  //#define Y_IS_TMC2208
-  //#define Y2_IS_TMC2208
-  //#define Z_IS_TMC2208
-  //#define Z2_IS_TMC2208
-  //#define E0_IS_TMC2208
-  //#define E1_IS_TMC2208
-  //#define E2_IS_TMC2208
-  //#define E3_IS_TMC2208
-  //#define E4_IS_TMC2208
-#endif
-
-#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
+#if HAS_TRINAMIC

  #define R_SENSE           0.11  // R_sense resistor for SilentStepStick2130
  #define HOLD_MULTIPLIER    0.5  // Scales down the holding current from run current
@ -1308,25 +1270,12 @@
 // @section L6470

 /**
- * Enable this section if you have L6470 motor drivers.
- * You need to import the L6470 library into the Arduino IDE for this.
- * (https://github.com/ameyer/Arduino-L6470)
+ * L6470 Stepper Driver options
+ *
+ * The Arduino-L6470 library is required for this stepper driver.
+ * https://github.com/ameyer/Arduino-L6470
 */
-
-//#define HAVE_L6470DRIVER
-#if ENABLED(HAVE_L6470DRIVER)
-
-  //#define X_IS_L6470
-  //#define X2_IS_L6470
-  //#define Y_IS_L6470
-  //#define Y2_IS_L6470
-  //#define Z_IS_L6470
-  //#define Z2_IS_L6470
-  //#define E0_IS_L6470
-  //#define E1_IS_L6470
-  //#define E2_IS_L6470
-  //#define E3_IS_L6470
-  //#define E4_IS_L6470
+#if HAS_DRIVER(L6470)

  #define X_MICROSTEPS      16 // number of microsteps
  #define X_OVERCURRENT   2000 // maxc current in mA. If the current goes over this value, the driver will switch off
@ -1372,7 +1321,7 @@
  #define E4_OVERCURRENT  2000
  #define E4_STALLCURRENT 1500

-#endif
+#endif // L6470

 /**
 * TWI/I2C BUS
--- a/Marlin/src/config/examples/wt150/Configuration.h
+++ b/Marlin/src/config/examples/wt150/Configuration.h
@ -556,6 +556,29 @@
 #define Z_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
 #define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.

+/**
+ * Specify Stepper Driver types
+ * The options are used to determine driver pulse timings as well as more advanced functionality.
+ * Stepper timing options can be overridden in Configuration_adv.h
+ *
+ * Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
+ *          TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
+ *          TMC26X,  TMC26X_STANDALONE,  TMC2660, TMC2660_STANDALONE,
+ *          TMC5130, TMC5130_STANDALONE
+ * :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
+ */
+#define X_DRIVER_TYPE  A4988
+#define Y_DRIVER_TYPE  A4988
+#define Z_DRIVER_TYPE  A4988
+#define X2_DRIVER_TYPE A4988
+#define Y2_DRIVER_TYPE A4988
+#define Z2_DRIVER_TYPE A4988
+#define E0_DRIVER_TYPE A4988
+#define E1_DRIVER_TYPE A4988
+#define E2_DRIVER_TYPE A4988
+#define E3_DRIVER_TYPE A4988
+#define E4_DRIVER_TYPE A4988
+
 // Enable this feature if all enabled endstop pins are interrupt-capable.
 // This will remove the need to poll the interrupt pins, saving many CPU cycles.
 //#define ENDSTOP_INTERRUPTS_FEATURE
--- a/Marlin/src/config/examples/wt150/Configuration_adv.h
+++ b/Marlin/src/config/examples/wt150/Configuration_adv.h
@ -838,15 +838,17 @@

 /**
 * Minimum delay after setting the stepper DIR (in ns)
- *    0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
- *   20 : Minimum for TMC2xxx drivers
- *  200 : Minimum for A4988 drivers
- *  500 : Minimum for LV8729 drivers (guess, no info in datasheet)
- *  650 : Minimum for DRV8825 drivers
- * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
- *15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *     0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
+ *    20 : Minimum for TMC2xxx drivers
+ *   200 : Minimum for A4988 drivers
+ *   500 : Minimum for LV8729 drivers (guess, no info in datasheet)
+ *   650 : Minimum for DRV8825 drivers
+ *  1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
+ * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_DIR_DELAY 0
+//#define MINIMUM_STEPPER_DIR_DELAY 650

 /**
 * Minimum stepper driver pulse width (in µs)
@ -856,8 +858,10 @@
 *   2 : Minimum for DRV8825 stepper drivers
 *   3 : Minimum for TB6600 stepper drivers
 *  30 : Minimum for TB6560 stepper drivers
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MINIMUM_STEPPER_PULSE 2
+//#define MINIMUM_STEPPER_PULSE 2

 /**
 * Maximum stepping rate (in Hz) the stepper driver allows
@ -868,8 +872,10 @@
 *  150000 : Maximum for TB6600 stepper driver
 *  130000 : Maximum for LV8729 stepper driver
 *   15000 : Maximum for TB6560 stepper driver
+ *
+ * Override the default value based on the driver type set in Configuration.h.
 */
-#define MAXIMUM_STEPPER_RATE 250000
+//#define MAXIMUM_STEPPER_RATE 250000

 // @section temperature

@ -1037,23 +1043,12 @@
 // @section tmc

 /**
- * Enable this section if you have TMC26X motor drivers.
- * You will need to import the TMC26XStepper library into the Arduino IDE for this
- * (https://github.com/trinamic/TMC26XStepper.git)
+ * TMC26X Stepper Driver options
+ *
+ * The TMC26XStepper library is required for this stepper driver.
+ * https://github.com/trinamic/TMC26XStepper
 */
-//#define HAVE_TMC26X
-#if ENABLED(HAVE_TMC26X)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC26X
-  //#define X2_IS_TMC26X
-  //#define Y_IS_TMC26X
-  //#define Y2_IS_TMC26X
-  //#define Z_IS_TMC26X
-  //#define Z2_IS_TMC26X
-  //#define E0_IS_TMC26X
-  //#define E1_IS_TMC26X
-  //#define E2_IS_TMC26X
-  //#define E3_IS_TMC26X
-  //#define E4_IS_TMC26X
+#if HAS_DRIVER(TMC26X)

  #define X_MAX_CURRENT     1000 // in mA
  #define X_SENSE_RESISTOR    91 // in mOhms
@ -1099,62 +1094,29 @@
  #define E4_SENSE_RESISTOR   91
  #define E4_MICROSTEPS       16

-#endif
+#endif // TMC26X

 // @section tmc_smart

 /**
- * Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
- *
- * You'll also need the TMC2130Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2130Stepper).
- *
 * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
 * the hardware SPI interface on your board and define the required CS pins
 * in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
 * You may also use software SPI if you wish to use general purpose IO pins.
- */
-//#define HAVE_TMC2130
-#if ENABLED(HAVE_TMC2130)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2130
-  //#define X2_IS_TMC2130
-  //#define Y_IS_TMC2130
-  //#define Y2_IS_TMC2130
-  //#define Z_IS_TMC2130
-  //#define Z2_IS_TMC2130
-  //#define E0_IS_TMC2130
-  //#define E1_IS_TMC2130
-  //#define E2_IS_TMC2130
-  //#define E3_IS_TMC2130
-  //#define E4_IS_TMC2130
-#endif
-
-/**
- * Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
- * Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
+ *
+ * The TMC2130Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2130Stepper
+ *
+ * To use TMC2208 stepper UART-configurable stepper drivers
+ * connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
 * To use the reading capabilities, also connect #_SERIAL_RX_PIN
 * to PDN_UART without a resistor.
 * The drivers can also be used with hardware serial.
 *
- * You'll also need the TMC2208Stepper Arduino library
- * (https://github.com/teemuatlut/TMC2208Stepper).
+ * The TMC2208Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2208Stepper
 */
-//#define HAVE_TMC2208
-#if ENABLED(HAVE_TMC2208)  // Choose your axes here. This is mandatory!
-  //#define X_IS_TMC2208
-  //#define X2_IS_TMC2208
-  //#define Y_IS_TMC2208
-  //#define Y2_IS_TMC2208
-  //#define Z_IS_TMC2208
-  //#define Z2_IS_TMC2208
-  //#define E0_IS_TMC2208
-  //#define E1_IS_TMC2208
-  //#define E2_IS_TMC2208
-  //#define E3_IS_TMC2208
-  //#define E4_IS_TMC2208
-#endif
-
-#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
+#if HAS_TRINAMIC

  #define R_SENSE           0.11  // R_sense resistor for SilentStepStick2130
  #define HOLD_MULTIPLIER    0.5  // Scales down the holding current from run current
@ -1309,25 +1271,12 @@
 // @section L6470

 /**
- * Enable this section if you have L6470 motor drivers.
- * You need to import the L6470 library into the Arduino IDE for this.
- * (https://github.com/ameyer/Arduino-L6470)
+ * L6470 Stepper Driver options
+ *
+ * The Arduino-L6470 library is required for this stepper driver.
+ * https://github.com/ameyer/Arduino-L6470
 */
-
-//#define HAVE_L6470DRIVER
-#if ENABLED(HAVE_L6470DRIVER)
-
-  //#define X_IS_L6470
-  //#define X2_IS_L6470
-  //#define Y_IS_L6470
-  //#define Y2_IS_L6470
-  //#define Z_IS_L6470
-  //#define Z2_IS_L6470
-  //#define E0_IS_L6470
-  //#define E1_IS_L6470
-  //#define E2_IS_L6470
-  //#define E3_IS_L6470
-  //#define E4_IS_L6470
+#if HAS_DRIVER(L6470)

  #define X_MICROSTEPS      16 // number of microsteps
  #define X_OVERCURRENT   2000 // maxc current in mA. If the current goes over this value, the driver will switch off
@ -1373,7 +1322,7 @@
  #define E4_OVERCURRENT  2000
  #define E4_STALLCURRENT 1500

-#endif
+#endif // L6470

 /**
 * TWI/I2C BUS
--- a/Marlin/src/core/drivers.h
+++ b/Marlin/src/core/drivers.h
@ -0,0 +1,57 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+#pragma once
+
+#define A4988               0x001
+#define DRV8825             0x002
+#define LV8729              0x003
+#define L6470               0x104
+#define TB6560              0x005
+#define TB6600              0x006
+#define TMC2100             0x007
+#define TMC2130             0x108
+#define TMC2130_STANDALONE  0x008
+#define TMC2208             0x109
+#define TMC2208_STANDALONE  0x009
+#define TMC26X              0x10A
+#define TMC26X_STANDALONE   0x00A
+#define TMC2660             0x10B
+#define TMC2660_STANDALONE  0x00B
+
+#define AXIS_DRIVER_TYPE(A, T) ( defined(A##_DRIVER_TYPE) && (A##_DRIVER_TYPE == T) )
+
+#define HAS_DRIVER(T)  (AXIS_DRIVER_TYPE( X,T) || AXIS_DRIVER_TYPE(X2,T) || \
+                        AXIS_DRIVER_TYPE( Y,T) || AXIS_DRIVER_TYPE(Y2,T) || \
+                        AXIS_DRIVER_TYPE( Z,T) || AXIS_DRIVER_TYPE(Z2,T) || \
+                        AXIS_DRIVER_TYPE(E0,T) || \
+                        AXIS_DRIVER_TYPE(E1,T) || \
+                        AXIS_DRIVER_TYPE(E2,T) || \
+                        AXIS_DRIVER_TYPE(E3,T) || \
+                        AXIS_DRIVER_TYPE(E4,T) )
+
+// Test for supported TMC drivers that require advanced configuration
+// Does not match standalone configurations
+#define HAS_TRINAMIC ( HAS_DRIVER(TMC2130) || HAS_DRIVER(TMC2208) || HAS_DRIVER(TMC2660) )
+
+#define AXIS_IS_TMC(A) ( AXIS_DRIVER_TYPE(A, TMC2130) || \
+                         AXIS_DRIVER_TYPE(A, TMC2208) || \
+                         AXIS_DRIVER_TYPE(A, TMC2660) )
--- a/Marlin/src/core/macros.h
+++ b/Marlin/src/core/macros.h
@ -20,8 +20,8 @@
 *
 */

-#ifndef MACROS_H
-#define MACROS_H
+#ifndef _CORE_MACROS_H_
+#define _CORE_MACROS_H_

 #define NUM_AXIS 4
 #define ABCE 4
@ -270,4 +270,4 @@
 #define FMOD(x, y)  fmodf(x, y)
 #define HYPOT(x,y)  SQRT(HYPOT2(x,y))

-#endif //__MACROS_H
+#endif // _CORE_MACROS_H_