diff --git a/.travis.yml b/.travis.yml
index f844a29eb7..8154ace313 100644
--- a/.travis.yml
+++ b/.travis.yml
@@ -161,6 +161,3 @@ script:
   #- rm -rf .build/
   #- ino build -m mega2560
   ######## Board Types #############
-  - sed -i 's/#define MOTHERBOARD BOARD_RAMPS_13_EFB/#define MOTHERBOARD BOARD_DUEMILANOVE_328P/g' Marlin/Configuration.h
-  - rm -rf .build/
-  - ino build -m atmega328
\ No newline at end of file
diff --git a/Marlin/Conditionals.h b/Marlin/Conditionals.h
index f09a8a2fe8..358131e4ae 100644
--- a/Marlin/Conditionals.h
+++ b/Marlin/Conditionals.h
@@ -22,15 +22,20 @@
     #define NEWPANEL
   #endif
 
-  #if defined(miniVIKI) || defined(VIKI2)
+  #if defined(miniVIKI) || defined(VIKI2) || defined(ELB_FULL_GRAPHIC_CONTROLLER)
     #define ULTRA_LCD  //general LCD support, also 16x2
     #define DOGLCD  // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family)
     #define ULTIMAKERCONTROLLER //as available from the Ultimaker online store.
 
     #ifdef miniVIKI
       #define DEFAULT_LCD_CONTRAST 95
-    #else
+    #elif defined(VIKI2)
       #define DEFAULT_LCD_CONTRAST 40
+    #elif defined(ELB_FULL_GRAPHIC_CONTROLLER)
+      #define DEFAULT_LCD_CONTRAST 110
+      #define SDCARDDETECTINVERTED
+      #define SDSLOW
+      #define U8GLIB_LM6059_AF
     #endif
 
     #define ENCODER_PULSES_PER_STEP 4
diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h
index 8e520fa96a..ccd9786811 100644
--- a/Marlin/Configuration.h
+++ b/Marlin/Configuration.h
@@ -660,6 +660,11 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
 //#define VIKI2
 //#define miniVIKI
 
+// This is a new controller currently under development.  https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/
+//
+// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib
+//#define ELB_FULL_GRAPHIC_CONTROLLER
+
 // The RepRapDiscount Smart Controller (white PCB)
 // http://reprap.org/wiki/RepRapDiscount_Smart_Controller
 //#define REPRAP_DISCOUNT_SMART_CONTROLLER
diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h
index fd41e9d0dc..8818b1b665 100644
--- a/Marlin/Configuration_adv.h
+++ b/Marlin/Configuration_adv.h
@@ -23,7 +23,7 @@
 
   /**
    * Whenever an M104 or M109 increases the target temperature the firmware will wait for the
-   * WATCH_TEMP_PERIOD to transpire, and if the temperature hasn't increased by WATCH_TEMP_INCREASE
+   * WATCH_TEMP_PERIOD to expire, and if the temperature hasn't increased by WATCH_TEMP_INCREASE
    * degrees, the machine is halted, requiring a hard reset. This test restarts with any M104/M109,
    * but only if the current temperature is far enough below the target for a reliable test.
    */
@@ -315,6 +315,17 @@
 
 #endif // SDSUPPORT
 
+// for dogm lcd displays you can choose some additional fonts:
+#ifdef DOGLCD
+  // save 3120 bytes of PROGMEM by commenting out #define USE_BIG_EDIT_FONT
+  // we don't have a big font for Cyrillic, Kana
+  //#define USE_BIG_EDIT_FONT
+ 
+  // If you have spare 2300Byte of progmem and want to use a 
+  // smaller font on the Info-screen uncomment the next line.
+  //#define USE_SMALL_INFOFONT
+#endif // DOGLCD
+
 // @section more
 
 // The hardware watchdog should reset the microcontroller disabling all outputs, in case the firmware gets stuck and doesn't do temperature regulation.
diff --git a/Marlin/Makefile b/Marlin/Makefile
index 34ad1340da..b22cca6713 100644
--- a/Marlin/Makefile
+++ b/Marlin/Makefile
@@ -99,12 +99,6 @@ else ifeq  ($(HARDWARE_MOTHERBOARD),34)
 HARDWARE_VARIANT ?= arduino
 MCU              ?= atmega2560
 
-#Duemilanove w/ ATMega328P pin assignment
-else ifeq  ($(HARDWARE_MOTHERBOARD),4)
-HARDWARE_VARIANT ?= arduino
-HARDWARE_SUB_VARIANT ?= standard
-MCU              ?= atmega328p
-
 #Gen6
 else ifeq  ($(HARDWARE_MOTHERBOARD),5)
 HARDWARE_VARIANT ?= Gen6
diff --git a/Marlin/Marlin_main.cpp b/Marlin/Marlin_main.cpp
index 7282adeb90..3b915306c6 100644
--- a/Marlin/Marlin_main.cpp
+++ b/Marlin/Marlin_main.cpp
@@ -6374,7 +6374,9 @@ void manage_inactivity(bool ignore_stepper_queue/*=false*/) {
 }
 
 void kill(const char *lcd_msg) {
-  lcd_setalertstatuspgm(lcd_msg);
+  #ifdef ULTRA_LCD
+    lcd_setalertstatuspgm(lcd_msg);
+  #endif
 
   cli(); // Stop interrupts
   disable_all_heaters();
diff --git a/Marlin/boards.h b/Marlin/boards.h
index cc9d1f2897..5ccf0f82e2 100644
--- a/Marlin/boards.h
+++ b/Marlin/boards.h
@@ -16,7 +16,6 @@
 #define BOARD_RAMPS_13_EEF      36   // RAMPS 1.3 / 1.4 (Power outputs: Extruder0, Extruder1, Fan)
 #define BOARD_RAMPS_13_SF       38   // RAMPS 1.3 / 1.4 (Power outputs: Spindle, Controller Fan)
 #define BOARD_FELIX2            37   // Felix 2.0+ Electronics Board (RAMPS like)
-#define BOARD_DUEMILANOVE_328P  4    // Duemilanove w/ ATMega328P pin assignments
 #define BOARD_GEN6              5    // Gen6
 #define BOARD_GEN6_DELUXE       51   // Gen6 deluxe
 #define BOARD_SANGUINOLOLU_11   6    // Sanguinololu < 1.2
diff --git a/Marlin/configurator/config/Configuration.h b/Marlin/configurator/config/Configuration.h
index de4c8a5f71..0d8a5d4228 100644
--- a/Marlin/configurator/config/Configuration.h
+++ b/Marlin/configurator/config/Configuration.h
@@ -661,6 +661,11 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
 //#define VIKI2
 //#define miniVIKI
 
+// This is a new controller currently under development.  https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/
+//
+// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib
+//#define ELB_FULL_GRAPHIC_CONTROLLER
+
 // The RepRapDiscount Smart Controller (white PCB)
 // http://reprap.org/wiki/RepRapDiscount_Smart_Controller
 //#define REPRAP_DISCOUNT_SMART_CONTROLLER
diff --git a/Marlin/configurator/config/Configuration_adv.h b/Marlin/configurator/config/Configuration_adv.h
index 1119e51814..91d8c9dc01 100644
--- a/Marlin/configurator/config/Configuration_adv.h
+++ b/Marlin/configurator/config/Configuration_adv.h
@@ -23,7 +23,7 @@
 
   /**
    * Whenever an M104 or M109 increases the target temperature the firmware will wait for the
-   * WATCH_TEMP_PERIOD to transpire, and if the temperature hasn't increased by WATCH_TEMP_INCREASE
+   * WATCH_TEMP_PERIOD to expire, and if the temperature hasn't increased by WATCH_TEMP_INCREASE
    * degrees, the machine is halted, requiring a hard reset. This test restarts with any M104/M109,
    * but only if the current temperature is far enough below the target for a reliable test.
    */
@@ -323,6 +323,17 @@
 
 #endif // SDSUPPORT
 
+// for dogm lcd displays you can choose some additional fonts:
+#ifdef DOGLCD
+  // save 3120 bytes of PROGMEM by commenting out #define USE_BIG_EDIT_FONT
+  // we don't have a big font for Cyrillic, Kana
+  //#define USE_BIG_EDIT_FONT
+ 
+  // If you have spare 2300Byte of progmem and want to use a 
+  // smaller font on the Info-screen uncomment the next line.
+  //#define USE_SMALL_INFOFONT
+#endif // DOGLCD
+
 // @section more
 
 // The hardware watchdog should reset the microcontroller disabling all outputs, in case the firmware gets stuck and doesn't do temperature regulation.
diff --git a/Marlin/configurator/config/boards.h b/Marlin/configurator/config/boards.h
index 8a60f011d5..0e9c8c20a1 100644
--- a/Marlin/configurator/config/boards.h
+++ b/Marlin/configurator/config/boards.h
@@ -15,7 +15,6 @@
 #define BOARD_RAMPS_13_EFF      35   // RAMPS 1.3 / 1.4 (Power outputs: Extruder, Fan, Fan)
 #define BOARD_RAMPS_13_EEF      36   // RAMPS 1.3 / 1.4 (Power outputs: Extruder0, Extruder1, Fan)
 #define BOARD_FELIX2            37   // Felix 2.0+ Electronics Board (RAMPS like)
-#define BOARD_DUEMILANOVE_328P  4    // Duemilanove w/ ATMega328P pin assignments
 #define BOARD_GEN6              5    // Gen6
 #define BOARD_GEN6_DELUXE       51   // Gen6 deluxe
 #define BOARD_SANGUINOLOLU_11   6    // Sanguinololu < 1.2
diff --git a/Marlin/dogm_lcd_implementation.h b/Marlin/dogm_lcd_implementation.h
index 47e4a9244d..d935d767a9 100644
--- a/Marlin/dogm_lcd_implementation.h
+++ b/Marlin/dogm_lcd_implementation.h
@@ -35,15 +35,11 @@
 #include "ultralcd_st7920_u8glib_rrd.h"
 #include "Configuration.h"
 
-// save 3120 bytes of PROGMEM by commenting out #define USE_BIG_EDIT_FONT
-// we don't have a big font for Cyrillic, Kana
-#if defined(MAPPER_C2C3) || defined(MAPPER_NON)
-  //#define USE_BIG_EDIT_FONT
+#if !defined(MAPPER_C2C3) && !defined(MAPPER_NON) && defined(USE_BIG_EDIT_FONT)
+   #undef USE_BIG_EDIT_FONT
 #endif
 
-// If you have spare 2300Byte of progmem and want to use a 
-// smaller font on the Info-screen uncomment the next line.
-//#define USE_SMALL_INFOFONT
+
 #ifdef USE_SMALL_INFOFONT
   #include "dogm_font_data_6x9_marlin.h"
   #define FONT_STATUSMENU_NAME u8g_font_6x9
@@ -126,6 +122,9 @@
 #elif defined(VIKI2) || defined(miniVIKI)
   // Mini Viki and Viki 2.0 LCD, ST7565 controller as well
   U8GLIB_NHD_C12864 u8g(DOGLCD_CS, DOGLCD_A0);
+#elif defined(U8GLIB_LM6059_AF)
+  // Based on the Adafruit ST7565 (http://www.adafruit.com/products/250)
+  U8GLIB_LM6059 u8g(DOGLCD_CS, DOGLCD_A0);
 #else
   // for regular DOGM128 display with HW-SPI
   U8GLIB_DOGM128 u8g(DOGLCD_CS, DOGLCD_A0);  // HW-SPI Com: CS, A0
diff --git a/Marlin/example_configurations/Felix/Configuration.h b/Marlin/example_configurations/Felix/Configuration.h
index 078af2a0d5..9df608264d 100644
--- a/Marlin/example_configurations/Felix/Configuration.h
+++ b/Marlin/example_configurations/Felix/Configuration.h
@@ -595,6 +595,11 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
 //#define VIKI2
 //#define miniVIKI
 
+// This is a new controller currently under development.  https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/
+//
+// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib
+//#define ELB_FULL_GRAPHIC_CONTROLLER
+
 // The RepRapDiscount Smart Controller (white PCB)
 // http://reprap.org/wiki/RepRapDiscount_Smart_Controller
 //#define REPRAP_DISCOUNT_SMART_CONTROLLER
diff --git a/Marlin/example_configurations/Felix/Configuration_adv.h b/Marlin/example_configurations/Felix/Configuration_adv.h
index 678ebbe083..24b0b93ebf 100644
--- a/Marlin/example_configurations/Felix/Configuration_adv.h
+++ b/Marlin/example_configurations/Felix/Configuration_adv.h
@@ -23,7 +23,7 @@
 
   /**
    * Whenever an M104 or M109 increases the target temperature the firmware will wait for the
-   * WATCH_TEMP_PERIOD to transpire, and if the temperature hasn't increased by WATCH_TEMP_INCREASE
+   * WATCH_TEMP_PERIOD to expire, and if the temperature hasn't increased by WATCH_TEMP_INCREASE
    * degrees, the machine is halted, requiring a hard reset. This test restarts with any M104/M109,
    * but only if the current temperature is far enough below the target for a reliable test.
    */
@@ -323,6 +323,18 @@
 
 #endif // SDSUPPORT
 
+// for dogm lcd displays you can choose some additional fonts:
+#ifdef DOGLCD
+  // save 3120 bytes of PROGMEM by commenting out #define USE_BIG_EDIT_FONT
+  // we don't have a big font for Cyrillic, Kana
+  //#define USE_BIG_EDIT_FONT
+ 
+  // If you have spare 2300Byte of progmem and want to use a 
+  // smaller font on the Info-screen uncomment the next line.
+  //#define USE_SMALL_INFOFONT
+#endif // DOGLCD
+
+
 // @section more
 
 // The hardware watchdog should reset the microcontroller disabling all outputs, in case the firmware gets stuck and doesn't do temperature regulation.
diff --git a/Marlin/example_configurations/Hephestos/Configuration.h b/Marlin/example_configurations/Hephestos/Configuration.h
index c5184ac6e4..4e8503aa6f 100644
--- a/Marlin/example_configurations/Hephestos/Configuration.h
+++ b/Marlin/example_configurations/Hephestos/Configuration.h
@@ -615,6 +615,11 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
 //#define VIKI2
 //#define miniVIKI
 
+// This is a new controller currently under development.  https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/
+//
+// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib
+//#define ELB_FULL_GRAPHIC_CONTROLLER
+
 // The RepRapDiscount Smart Controller (white PCB)
 // http://reprap.org/wiki/RepRapDiscount_Smart_Controller
 #define REPRAP_DISCOUNT_SMART_CONTROLLER
diff --git a/Marlin/example_configurations/Hephestos/Configuration_adv.h b/Marlin/example_configurations/Hephestos/Configuration_adv.h
index e1ec3fa6a7..485afd15b5 100644
--- a/Marlin/example_configurations/Hephestos/Configuration_adv.h
+++ b/Marlin/example_configurations/Hephestos/Configuration_adv.h
@@ -23,7 +23,7 @@
 
   /**
    * Whenever an M104 or M109 increases the target temperature the firmware will wait for the
-   * WATCH_TEMP_PERIOD to transpire, and if the temperature hasn't increased by WATCH_TEMP_INCREASE
+   * WATCH_TEMP_PERIOD to expire, and if the temperature hasn't increased by WATCH_TEMP_INCREASE
    * degrees, the machine is halted, requiring a hard reset. This test restarts with any M104/M109,
    * but only if the current temperature is far enough below the target for a reliable test.
    */
@@ -323,6 +323,18 @@
 
 #endif // SDSUPPORT
 
+// for dogm lcd displays you can choose some additional fonts:
+#ifdef DOGLCD
+  // save 3120 bytes of PROGMEM by commenting out #define USE_BIG_EDIT_FONT
+  // we don't have a big font for Cyrillic, Kana
+  //#define USE_BIG_EDIT_FONT
+ 
+  // If you have spare 2300Byte of progmem and want to use a 
+  // smaller font on the Info-screen uncomment the next line.
+  //#define USE_SMALL_INFOFONT
+#endif // DOGLCD
+
+
 // @section more
 
 // The hardware watchdog should reset the microcontroller disabling all outputs, in case the firmware gets stuck and doesn't do temperature regulation.
diff --git a/Marlin/example_configurations/K8200/Configuration.h b/Marlin/example_configurations/K8200/Configuration.h
index f4fccc82ac..b430543ef5 100644
--- a/Marlin/example_configurations/K8200/Configuration.h
+++ b/Marlin/example_configurations/K8200/Configuration.h
@@ -678,6 +678,11 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
 //#define VIKI2
 //#define miniVIKI
 
+// This is a new controller currently under development.  https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/
+//
+// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib
+//#define ELB_FULL_GRAPHIC_CONTROLLER
+
 // The RepRapDiscount Smart Controller (white PCB)
 // http://reprap.org/wiki/RepRapDiscount_Smart_Controller
 //#define REPRAP_DISCOUNT_SMART_CONTROLLER
diff --git a/Marlin/example_configurations/K8200/Configuration_adv.h b/Marlin/example_configurations/K8200/Configuration_adv.h
index 678ebbe083..24b0b93ebf 100644
--- a/Marlin/example_configurations/K8200/Configuration_adv.h
+++ b/Marlin/example_configurations/K8200/Configuration_adv.h
@@ -23,7 +23,7 @@
 
   /**
    * Whenever an M104 or M109 increases the target temperature the firmware will wait for the
-   * WATCH_TEMP_PERIOD to transpire, and if the temperature hasn't increased by WATCH_TEMP_INCREASE
+   * WATCH_TEMP_PERIOD to expire, and if the temperature hasn't increased by WATCH_TEMP_INCREASE
    * degrees, the machine is halted, requiring a hard reset. This test restarts with any M104/M109,
    * but only if the current temperature is far enough below the target for a reliable test.
    */
@@ -323,6 +323,18 @@
 
 #endif // SDSUPPORT
 
+// for dogm lcd displays you can choose some additional fonts:
+#ifdef DOGLCD
+  // save 3120 bytes of PROGMEM by commenting out #define USE_BIG_EDIT_FONT
+  // we don't have a big font for Cyrillic, Kana
+  //#define USE_BIG_EDIT_FONT
+ 
+  // If you have spare 2300Byte of progmem and want to use a 
+  // smaller font on the Info-screen uncomment the next line.
+  //#define USE_SMALL_INFOFONT
+#endif // DOGLCD
+
+
 // @section more
 
 // The hardware watchdog should reset the microcontroller disabling all outputs, in case the firmware gets stuck and doesn't do temperature regulation.
diff --git a/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h b/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h
index 27a2582900..b98c72437a 100644
--- a/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h
+++ b/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h
@@ -661,6 +661,11 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
 //#define VIKI2
 //#define miniVIKI
 
+// This is a new controller currently under development.  https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/
+//
+// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib
+//#define ELB_FULL_GRAPHIC_CONTROLLER
+
 // The RepRapDiscount Smart Controller (white PCB)
 // http://reprap.org/wiki/RepRapDiscount_Smart_Controller
 //#define REPRAP_DISCOUNT_SMART_CONTROLLER
diff --git a/Marlin/example_configurations/SCARA/Configuration.h b/Marlin/example_configurations/SCARA/Configuration.h
index e4941a7fd6..aa623d2db5 100644
--- a/Marlin/example_configurations/SCARA/Configuration.h
+++ b/Marlin/example_configurations/SCARA/Configuration.h
@@ -646,6 +646,11 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
 //#define VIKI2
 //#define miniVIKI
 
+// This is a new controller currently under development.  https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/
+//
+// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib
+//#define ELB_FULL_GRAPHIC_CONTROLLER
+
 // The RepRapDiscount Smart Controller (white PCB)
 // http://reprap.org/wiki/RepRapDiscount_Smart_Controller
 //#define REPRAP_DISCOUNT_SMART_CONTROLLER
diff --git a/Marlin/example_configurations/SCARA/Configuration_adv.h b/Marlin/example_configurations/SCARA/Configuration_adv.h
index af4429b7e6..b2e05ef373 100644
--- a/Marlin/example_configurations/SCARA/Configuration_adv.h
+++ b/Marlin/example_configurations/SCARA/Configuration_adv.h
@@ -23,7 +23,7 @@
 
   /**
    * Whenever an M104 or M109 increases the target temperature the firmware will wait for the
-   * WATCH_TEMP_PERIOD to transpire, and if the temperature hasn't increased by WATCH_TEMP_INCREASE
+   * WATCH_TEMP_PERIOD to expire, and if the temperature hasn't increased by WATCH_TEMP_INCREASE
    * degrees, the machine is halted, requiring a hard reset. This test restarts with any M104/M109,
    * but only if the current temperature is far enough below the target for a reliable test.
    */
@@ -323,6 +323,18 @@
 
 #endif // SDSUPPORT
 
+// for dogm lcd displays you can choose some additional fonts:
+#ifdef DOGLCD
+  // save 3120 bytes of PROGMEM by commenting out #define USE_BIG_EDIT_FONT
+  // we don't have a big font for Cyrillic, Kana
+  //#define USE_BIG_EDIT_FONT
+ 
+  // If you have spare 2300Byte of progmem and want to use a 
+  // smaller font on the Info-screen uncomment the next line.
+  //#define USE_SMALL_INFOFONT
+#endif // DOGLCD
+
+
 // @section more
 
 // The hardware watchdog should reset the microcontroller disabling all outputs, in case the firmware gets stuck and doesn't do temperature regulation.
diff --git a/Marlin/example_configurations/WITBOX/Configuration.h b/Marlin/example_configurations/WITBOX/Configuration.h
index f0c71c16de..f9543b0c45 100644
--- a/Marlin/example_configurations/WITBOX/Configuration.h
+++ b/Marlin/example_configurations/WITBOX/Configuration.h
@@ -614,6 +614,11 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
 //#define VIKI2
 //#define miniVIKI
 
+// This is a new controller currently under development.  https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/
+//
+// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib
+//#define ELB_FULL_GRAPHIC_CONTROLLER
+
 // The RepRapDiscount Smart Controller (white PCB)
 // http://reprap.org/wiki/RepRapDiscount_Smart_Controller
 #define REPRAP_DISCOUNT_SMART_CONTROLLER
diff --git a/Marlin/example_configurations/WITBOX/Configuration_adv.h b/Marlin/example_configurations/WITBOX/Configuration_adv.h
index da2281eaf8..2d187ae45f 100644
--- a/Marlin/example_configurations/WITBOX/Configuration_adv.h
+++ b/Marlin/example_configurations/WITBOX/Configuration_adv.h
@@ -23,7 +23,7 @@
 
   /**
    * Whenever an M104 or M109 increases the target temperature the firmware will wait for the
-   * WATCH_TEMP_PERIOD to transpire, and if the temperature hasn't increased by WATCH_TEMP_INCREASE
+   * WATCH_TEMP_PERIOD to expire, and if the temperature hasn't increased by WATCH_TEMP_INCREASE
    * degrees, the machine is halted, requiring a hard reset. This test restarts with any M104/M109,
    * but only if the current temperature is far enough below the target for a reliable test.
    */
@@ -323,6 +323,18 @@
 
 #endif // SDSUPPORT
 
+// for dogm lcd displays you can choose some additional fonts:
+#ifdef DOGLCD
+  // save 3120 bytes of PROGMEM by commenting out #define USE_BIG_EDIT_FONT
+  // we don't have a big font for Cyrillic, Kana
+  //#define USE_BIG_EDIT_FONT
+ 
+  // If you have spare 2300Byte of progmem and want to use a 
+  // smaller font on the Info-screen uncomment the next line.
+  //#define USE_SMALL_INFOFONT
+#endif // DOGLCD
+
+
 // @section more
 
 // The hardware watchdog should reset the microcontroller disabling all outputs, in case the firmware gets stuck and doesn't do temperature regulation.
diff --git a/Marlin/example_configurations/delta/biv2.5/Configuration.h b/Marlin/example_configurations/delta/biv2.5/Configuration.h
index 908acce5ab..f86b2da382 100644
--- a/Marlin/example_configurations/delta/biv2.5/Configuration.h
+++ b/Marlin/example_configurations/delta/biv2.5/Configuration.h
@@ -660,6 +660,11 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
 //#define VIKI2
 //#define miniVIKI
 
+// This is a new controller currently under development.  https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/
+//
+// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib
+//#define ELB_FULL_GRAPHIC_CONTROLLER
+
 // The RepRapDiscount Smart Controller (white PCB)
 // http://reprap.org/wiki/RepRapDiscount_Smart_Controller
 //#define REPRAP_DISCOUNT_SMART_CONTROLLER
diff --git a/Marlin/example_configurations/delta/biv2.5/Configuration_adv.h b/Marlin/example_configurations/delta/biv2.5/Configuration_adv.h
index e193015cc3..9a9104e60c 100644
--- a/Marlin/example_configurations/delta/biv2.5/Configuration_adv.h
+++ b/Marlin/example_configurations/delta/biv2.5/Configuration_adv.h
@@ -23,7 +23,7 @@
 
   /**
    * Whenever an M104 or M109 increases the target temperature the firmware will wait for the
-   * WATCH_TEMP_PERIOD to transpire, and if the temperature hasn't increased by WATCH_TEMP_INCREASE
+   * WATCH_TEMP_PERIOD to expire, and if the temperature hasn't increased by WATCH_TEMP_INCREASE
    * degrees, the machine is halted, requiring a hard reset. This test restarts with any M104/M109,
    * but only if the current temperature is far enough below the target for a reliable test.
    */
@@ -324,6 +324,17 @@
 
 #endif // SDSUPPORT
 
+// for dogm lcd displays you can choose some additional fonts:
+#ifdef DOGLCD
+  // save 3120 bytes of PROGMEM by commenting out #define USE_BIG_EDIT_FONT
+  // we don't have a big font for Cyrillic, Kana
+  //#define USE_BIG_EDIT_FONT
+ 
+  // If you have spare 2300Byte of progmem and want to use a 
+  // smaller font on the Info-screen uncomment the next line.
+  //#define USE_SMALL_INFOFONT
+#endif // DOGLCD
+
 // @section more
 
 // The hardware watchdog should reset the microcontroller disabling all outputs, in case the firmware gets stuck and doesn't do temperature regulation.
diff --git a/Marlin/example_configurations/delta/generic/Configuration.h b/Marlin/example_configurations/delta/generic/Configuration.h
index 0a5b7e6711..6aeb7fa41f 100644
--- a/Marlin/example_configurations/delta/generic/Configuration.h
+++ b/Marlin/example_configurations/delta/generic/Configuration.h
@@ -663,6 +663,11 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
 //#define VIKI2
 //#define miniVIKI
 
+// This is a new controller currently under development.  https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/
+//
+// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib
+//#define ELB_FULL_GRAPHIC_CONTROLLER
+
 // The RepRapDiscount Smart Controller (white PCB)
 // http://reprap.org/wiki/RepRapDiscount_Smart_Controller
 //#define REPRAP_DISCOUNT_SMART_CONTROLLER
diff --git a/Marlin/example_configurations/delta/generic/Configuration_adv.h b/Marlin/example_configurations/delta/generic/Configuration_adv.h
index a003186d81..9a86fc83ff 100644
--- a/Marlin/example_configurations/delta/generic/Configuration_adv.h
+++ b/Marlin/example_configurations/delta/generic/Configuration_adv.h
@@ -23,7 +23,7 @@
 
   /**
    * Whenever an M104 or M109 increases the target temperature the firmware will wait for the
-   * WATCH_TEMP_PERIOD to transpire, and if the temperature hasn't increased by WATCH_TEMP_INCREASE
+   * WATCH_TEMP_PERIOD to expire, and if the temperature hasn't increased by WATCH_TEMP_INCREASE
    * degrees, the machine is halted, requiring a hard reset. This test restarts with any M104/M109,
    * but only if the current temperature is far enough below the target for a reliable test.
    */
@@ -324,6 +324,18 @@
 
 #endif // SDSUPPORT
 
+// for dogm lcd displays you can choose some additional fonts:
+#ifdef DOGLCD
+  // save 3120 bytes of PROGMEM by commenting out #define USE_BIG_EDIT_FONT
+  // we don't have a big font for Cyrillic, Kana
+  //#define USE_BIG_EDIT_FONT
+ 
+  // If you have spare 2300Byte of progmem and want to use a 
+  // smaller font on the Info-screen uncomment the next line.
+  //#define USE_SMALL_INFOFONT
+#endif // DOGLCD
+
+
 // @section more
 
 // The hardware watchdog should reset the microcontroller disabling all outputs, in case the firmware gets stuck and doesn't do temperature regulation.
diff --git a/Marlin/example_configurations/delta/kossel_mini/Configuration.h b/Marlin/example_configurations/delta/kossel_mini/Configuration.h
index 87d1cd2a1e..0f7662892e 100644
--- a/Marlin/example_configurations/delta/kossel_mini/Configuration.h
+++ b/Marlin/example_configurations/delta/kossel_mini/Configuration.h
@@ -667,6 +667,11 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
 //#define VIKI2
 //#define miniVIKI
 
+// This is a new controller currently under development.  https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/
+//
+// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib
+//#define ELB_FULL_GRAPHIC_CONTROLLER
+
 // The RepRapDiscount Smart Controller (white PCB)
 // http://reprap.org/wiki/RepRapDiscount_Smart_Controller
 //#define REPRAP_DISCOUNT_SMART_CONTROLLER
diff --git a/Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h b/Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h
index c8ac659c32..8cd7786172 100644
--- a/Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h
+++ b/Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h
@@ -23,7 +23,7 @@
 
   /**
    * Whenever an M104 or M109 increases the target temperature the firmware will wait for the
-   * WATCH_TEMP_PERIOD to transpire, and if the temperature hasn't increased by WATCH_TEMP_INCREASE
+   * WATCH_TEMP_PERIOD to expire, and if the temperature hasn't increased by WATCH_TEMP_INCREASE
    * degrees, the machine is halted, requiring a hard reset. This test restarts with any M104/M109,
    * but only if the current temperature is far enough below the target for a reliable test.
    */
@@ -323,6 +323,18 @@
 
 #endif // SDSUPPORT
 
+// for dogm lcd displays you can choose some additional fonts:
+#ifdef DOGLCD
+  // save 3120 bytes of PROGMEM by commenting out #define USE_BIG_EDIT_FONT
+  // we don't have a big font for Cyrillic, Kana
+  //#define USE_BIG_EDIT_FONT
+ 
+  // If you have spare 2300Byte of progmem and want to use a 
+  // smaller font on the Info-screen uncomment the next line.
+  //#define USE_SMALL_INFOFONT
+#endif // DOGLCD
+
+
 // @section more
 
 // The hardware watchdog should reset the microcontroller disabling all outputs, in case the firmware gets stuck and doesn't do temperature regulation.
diff --git a/Marlin/example_configurations/makibox/Configuration.h b/Marlin/example_configurations/makibox/Configuration.h
index 63a4024673..33419bd87a 100644
--- a/Marlin/example_configurations/makibox/Configuration.h
+++ b/Marlin/example_configurations/makibox/Configuration.h
@@ -614,6 +614,11 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
 //#define VIKI2
 //#define miniVIKI
 
+// This is a new controller currently under development.  https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/
+//
+// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib
+//#define ELB_FULL_GRAPHIC_CONTROLLER
+
 // The RepRapDiscount Smart Controller (white PCB)
 // http://reprap.org/wiki/RepRapDiscount_Smart_Controller
 //#define REPRAP_DISCOUNT_SMART_CONTROLLER
diff --git a/Marlin/example_configurations/makibox/Configuration_adv.h b/Marlin/example_configurations/makibox/Configuration_adv.h
index b08e8bc2ff..d502852d44 100644
--- a/Marlin/example_configurations/makibox/Configuration_adv.h
+++ b/Marlin/example_configurations/makibox/Configuration_adv.h
@@ -23,7 +23,7 @@
 
   /**
    * Whenever an M104 or M109 increases the target temperature the firmware will wait for the
-   * WATCH_TEMP_PERIOD to transpire, and if the temperature hasn't increased by WATCH_TEMP_INCREASE
+   * WATCH_TEMP_PERIOD to expire, and if the temperature hasn't increased by WATCH_TEMP_INCREASE
    * degrees, the machine is halted, requiring a hard reset. This test restarts with any M104/M109,
    * but only if the current temperature is far enough below the target for a reliable test.
    */
@@ -323,6 +323,18 @@
 
 #endif // SDSUPPORT
 
+// for dogm lcd displays you can choose some additional fonts:
+#ifdef DOGLCD
+  // save 3120 bytes of PROGMEM by commenting out #define USE_BIG_EDIT_FONT
+  // we don't have a big font for Cyrillic, Kana
+  //#define USE_BIG_EDIT_FONT
+ 
+  // If you have spare 2300Byte of progmem and want to use a 
+  // smaller font on the Info-screen uncomment the next line.
+  //#define USE_SMALL_INFOFONT
+#endif // DOGLCD
+
+
 // @section more
 
 // The hardware watchdog should reset the microcontroller disabling all outputs, in case the firmware gets stuck and doesn't do temperature regulation.
diff --git a/Marlin/example_configurations/tvrrug/Round2/Configuration.h b/Marlin/example_configurations/tvrrug/Round2/Configuration.h
index 0dd00045b2..a317358a9d 100644
--- a/Marlin/example_configurations/tvrrug/Round2/Configuration.h
+++ b/Marlin/example_configurations/tvrrug/Round2/Configuration.h
@@ -620,6 +620,11 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
 //#define VIKI2
 //#define miniVIKI
 
+// This is a new controller currently under development.  https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/
+//
+// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib
+//#define ELB_FULL_GRAPHIC_CONTROLLER
+
 // The RepRapDiscount Smart Controller (white PCB)
 // http://reprap.org/wiki/RepRapDiscount_Smart_Controller
 //#define REPRAP_DISCOUNT_SMART_CONTROLLER
diff --git a/Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h b/Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h
index a86b3279d4..85b75e1a11 100644
--- a/Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h
+++ b/Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h
@@ -23,7 +23,7 @@
 
   /**
    * Whenever an M104 or M109 increases the target temperature the firmware will wait for the
-   * WATCH_TEMP_PERIOD to transpire, and if the temperature hasn't increased by WATCH_TEMP_INCREASE
+   * WATCH_TEMP_PERIOD to expire, and if the temperature hasn't increased by WATCH_TEMP_INCREASE
    * degrees, the machine is halted, requiring a hard reset. This test restarts with any M104/M109,
    * but only if the current temperature is far enough below the target for a reliable test.
    */
@@ -323,6 +323,18 @@
 
 #endif // SDSUPPORT
 
+// for dogm lcd displays you can choose some additional fonts:
+#ifdef DOGLCD
+  // save 3120 bytes of PROGMEM by commenting out #define USE_BIG_EDIT_FONT
+  // we don't have a big font for Cyrillic, Kana
+  //#define USE_BIG_EDIT_FONT
+ 
+  // If you have spare 2300Byte of progmem and want to use a 
+  // smaller font on the Info-screen uncomment the next line.
+  //#define USE_SMALL_INFOFONT
+#endif // DOGLCD
+
+
 // @section more
 
 // The hardware watchdog should reset the microcontroller disabling all outputs, in case the firmware gets stuck and doesn't do temperature regulation.
diff --git a/Marlin/language.h b/Marlin/language.h
index 096b416c04..6e078d1dbc 100644
--- a/Marlin/language.h
+++ b/Marlin/language.h
@@ -32,8 +32,8 @@
 // kana_utf Japanese
 // cn       Chinese
 
+// fallback if no language is set, don't change
 #ifndef LANGUAGE_INCLUDE
-  // pick your language from the list above
   #define LANGUAGE_INCLUDE GENERATE_LANGUAGE_INCLUDE(en)
 #endif
 
@@ -53,6 +53,7 @@
   #define FIRMWARE_URL "http://3dprint.elettronicain.it/"
 #elif MB(K8200)
   #define MACHINE_NAME "K8200"
+  #define FIRMWARE_URL "https://github.com/CONSULitAS/Marlin-K8200"
 #elif MB(5DPRINT)
   #define MACHINE_NAME "Makibox"
 #elif MB(SAV_MKI)
diff --git a/Marlin/pins.h b/Marlin/pins.h
index 6af115d63a..abffe2c934 100644
--- a/Marlin/pins.h
+++ b/Marlin/pins.h
@@ -36,8 +36,6 @@
   #include "pins_RAMPS_OLD.h"
 #elif MB(RAMPS_13_EFB) || MB(RAMPS_13_EEB) || MB(RAMPS_13_EFF) || MB(RAMPS_13_EEF) || MB(RAMPS_13_SF)
   #include "pins_RAMPS_13.h"
-#elif MB(DUEMILANOVE_328P)
-  #include "pins_DUEMILANOVE_328P.h"
 #elif MB(GEN6)
   #include "pins_GEN6.h"
 #elif MB(GEN6_DELUXE)
diff --git a/Marlin/pins_DUEMILANOVE_328P.h b/Marlin/pins_DUEMILANOVE_328P.h
deleted file mode 100644
index 9e47055849..0000000000
--- a/Marlin/pins_DUEMILANOVE_328P.h
+++ /dev/null
@@ -1,43 +0,0 @@
-/**
- * Duemilanove w/ ATMega328P pin assignments
- */
-
-#ifndef __AVR_ATmega328P__
-  #error Oops!  Make sure you have 'Arduino Duemilanove w/ ATMega328' selected from the 'Tools -> Boards' menu.
-#endif
-
-#define X_STEP_PIN         19
-#define X_DIR_PIN          18
-#define X_ENABLE_PIN       -1
-#define X_STOP_PIN         17
-
-#define Y_STEP_PIN         10
-#define Y_DIR_PIN           7
-#define Y_ENABLE_PIN       -1
-#define Y_STOP_PIN          8
-
-#define Z_STEP_PIN         13
-#define Z_DIR_PIN           3
-#define Z_ENABLE_PIN        2
-#define Z_STOP_PIN          4
-
-#define E0_STEP_PIN         11
-#define E0_DIR_PIN          12
-#define E0_ENABLE_PIN       -1
-
-#define SDPOWER          -1
-#define SDSS          -1
-#define LED_PIN            -1
-#define FAN_PIN             5
-#define PS_ON_PIN          -1
-#define KILL_PIN           -1
-
-#define HEATER_0_PIN        6
-#define HEATER_1_PIN        -1
-#define HEATER_2_PIN        -1
-#define TEMP_0_PIN          0    // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!!
-#define TEMP_1_PIN          -1
-#define TEMP_2_PIN          -1
-#define HEATER_BED_PIN      -1
-#define TEMP_BED_PIN        -1
-
diff --git a/Marlin/pins_RAMPS_13.h b/Marlin/pins_RAMPS_13.h
index c9c796ed42..37683b8c59 100644
--- a/Marlin/pins_RAMPS_13.h
+++ b/Marlin/pins_RAMPS_13.h
@@ -180,6 +180,17 @@
       #define BTN_ENC -1
       #define LCD_SDSS 53
       #define SDCARDDETECT 49
+    #elif defined(ELB_FULL_GRAPHIC_CONTROLLER)
+      #define BTN_EN1 35  // reverse if the encoder turns the wrong way.
+      #define BTN_EN2 37
+      #define BTN_ENC 31
+      #define SDCARDDETECT 49
+      #define LCD_SDSS 53
+      #define KILL_PIN 41
+      #define BEEPER 23
+      #define DOGLCD_CS 29
+      #define DOGLCD_A0 27
+      #define LCD_PIN_BL 33
     #else
       // arduino pin which triggers an piezzo beeper
       #define BEEPER 33  // Beeper on AUX-4
@@ -209,7 +220,6 @@
       #endif
 
     #endif
-
   #else // Old-style panel with shift register
     // Arduino pin witch triggers an piezzo beeper
     #define BEEPER 33   // No Beeper added
diff --git a/Marlin/temperature.cpp b/Marlin/temperature.cpp
index fea4e96152..9fdcb785cd 100644
--- a/Marlin/temperature.cpp
+++ b/Marlin/temperature.cpp
@@ -312,7 +312,8 @@ void PID_autotune(float temp, int extruder, int ncycles)
         }
       } 
     }
-    if (input > temp + 20) {
+    #define MAX_OVERSHOOT_PID_AUTOTUNE 20
+    if (input > temp + MAX_OVERSHOOT_PID_AUTOTUNE) {
       SERIAL_PROTOCOLLNPGM(MSG_PID_TEMP_TOO_HIGH);
       return;
     }
diff --git a/Marlin/ultralcd.cpp b/Marlin/ultralcd.cpp
index 1bcd3dbaae..8584a963d5 100644
--- a/Marlin/ultralcd.cpp
+++ b/Marlin/ultralcd.cpp
@@ -1110,13 +1110,24 @@ static void lcd_control_volumetric_menu() {
 #ifdef HAS_LCD_CONTRAST
   static void lcd_set_contrast() {
     if (encoderPosition != 0) {
-      lcd_contrast -= encoderPosition;
-      lcd_contrast &= 0x3F;
+      #ifdef U8GLIB_LM6059_AF
+        lcd_contrast += encoderPosition;
+        lcd_contrast &= 0xFF;
+      #else
+        lcd_contrast -= encoderPosition;
+        lcd_contrast &= 0x3F;
+      #endif
       encoderPosition = 0;
       lcdDrawUpdate = 1;
       u8g.setContrast(lcd_contrast);
     }
-    if (lcdDrawUpdate) lcd_implementation_drawedit(PSTR(MSG_CONTRAST), itostr2(lcd_contrast));
+    if (lcdDrawUpdate) {
+      #ifdef U8GLIB_LM6059_AF
+        lcd_implementation_drawedit(PSTR(MSG_CONTRAST), itostr3(lcd_contrast));
+      #else
+        lcd_implementation_drawedit(PSTR(MSG_CONTRAST), itostr2(lcd_contrast));
+      #endif
+    }
     if (LCD_CLICKED) lcd_goto_menu(lcd_control_menu);
   }
 #endif // HAS_LCD_CONTRAST