diff --git a/Marlin/src/module/temperature.cpp b/Marlin/src/module/temperature.cpp index 5bed31b1a1..de64c28c85 100644 --- a/Marlin/src/module/temperature.cpp +++ b/Marlin/src/module/temperature.cpp @@ -2798,133 +2798,23 @@ void Temperature::tick() { if ((do_buttons ^= true)) ui.update_buttons(); /** - * On each call to the ISR one sensor is Sampled and - * the next sensor is Prepared. + * One sensor is sampled on every other call of the ISR. + * Each sensor is read 16 (OVERSAMPLENR) times, taking the average. * - * Sensors are read 16 (OVERSAMPLENR) times and the - * final reading takes the average. + * On each Prepare pass, ADC is started for a sensor pin. + * On the next pass, the ADC value is read and accumulated. * - * Extra do-nothing passes may exist when there are - * only a few sensors. This is set by MIN_ADC_ISR_LOOPS. - * - * The timing of this ISR gives ADCs 0.9765ms to charge up. + * This gives each ADC 0.9765ms to charge up. */ - #define ACCUMULATE_ADC(obj) do{ \ - if (HAL_ADC_READY()) \ - obj.sample(HAL_READ_ADC()); \ - else \ - next_sensor_state = adc_sensor_state; \ + #define ACCUMULATE_ADC(obj) do{ \ + if (!HAL_ADC_READY()) next_sensor_state = adc_sensor_state; \ + else obj.sample(HAL_READ_ADC()); \ }while(0) - #define NEXT_ENUM(A) (typeof(A))(int(A) + 1) - #define NEXT_ADC_STATE(N) ((N) >= SensorsReady ? StartSampling : NEXT_ENUM(N)) - - // Assume the machine will go on to the next state - ADCSensorState next_sensor_state = NEXT_ADC_STATE(adc_sensor_state); - - switch (adc_sensor_state) { - - default: break; - - #if HAS_TEMP_ADC_0 - case MeasureTemp_0: ACCUMULATE_ADC(temp_hotend[0]); break; - #endif - #if HAS_HEATED_BED - case MeasureTemp_BED: ACCUMULATE_ADC(temp_bed); break; - #endif - #if HAS_TEMP_CHAMBER - case MeasureTemp_CHAMBER: ACCUMULATE_ADC(temp_chamber); break; - #endif - #if HAS_TEMP_PROBE - case MeasureTemp_PROBE: ACCUMULATE_ADC(temp_probe); break; - #endif - #if HAS_TEMP_ADC_1 - case MeasureTemp_1: ACCUMULATE_ADC(temp_hotend[1]); break; - #endif - #if HAS_TEMP_ADC_2 - case MeasureTemp_2: ACCUMULATE_ADC(temp_hotend[2]); break; - #endif - #if HAS_TEMP_ADC_3 - case MeasureTemp_3: ACCUMULATE_ADC(temp_hotend[3]); break; - #endif - #if HAS_TEMP_ADC_4 - case MeasureTemp_4: ACCUMULATE_ADC(temp_hotend[4]); break; - #endif - #if HAS_TEMP_ADC_5 - case MeasureTemp_5: ACCUMULATE_ADC(temp_hotend[5]); break; - #endif - #if HAS_TEMP_ADC_6 - case MeasureTemp_6: ACCUMULATE_ADC(temp_hotend[6]); break; - #endif - #if HAS_TEMP_ADC_7 - case MeasureTemp_7: ACCUMULATE_ADC(temp_hotend[7]); break; - #endif - - #if ENABLED(FILAMENT_WIDTH_SENSOR) - case Measure_FILWIDTH: - if (HAL_ADC_READY()) - filwidth.accumulate(HAL_READ_ADC()); - else - next_sensor_state = adc_sensor_state; // redo this state - break; - #endif - - #if HAS_JOY_ADC_X - case MeasureJoy_X: ACCUMULATE_ADC(joystick.x); break; - #endif - #if HAS_JOY_ADC_Y - case MeasureJoy_Y: ACCUMULATE_ADC(joystick.y); break; - #endif - #if HAS_JOY_ADC_Z - case MeasureJoy_Z: ACCUMULATE_ADC(joystick.z); break; - #endif - - #if HAS_ADC_BUTTONS - #ifndef ADC_BUTTON_DEBOUNCE_DELAY - #define ADC_BUTTON_DEBOUNCE_DELAY 16 - #endif - case Measure_ADC_KEY: { - if (HAL_ADC_READY()) { - if (ADCKey_count < ADC_BUTTON_DEBOUNCE_DELAY) { - raw_ADCKey_value = HAL_READ_ADC(); - if (raw_ADCKey_value <= (HAL_ADC_RANGE) * 900UL / 1024UL) { - NOMORE(current_ADCKey_raw, raw_ADCKey_value); - ADCKey_count++; - } - else { // ADC Key release - if (ADCKey_count > 0) { - if (ADCKey_pressed) { - ADCKey_count = 0; - current_ADCKey_raw = HAL_ADC_RANGE; - } - else - ADCKey_count++; - } - else - ADCKey_pressed = false; - } - if (ADCKey_count == ADC_BUTTON_DEBOUNCE_DELAY) ADCKey_pressed = true; - } - } - else - next_sensor_state = adc_sensor_state; // redo this state - - } break; - - #endif // HAS_ADC_BUTTONS - - } // switch(adc_sensor_state) - - // Go to the next state (may be unchanged) - adc_sensor_state = next_sensor_state; - - // Assume that the state advances - next_sensor_state = NEXT_ADC_STATE(adc_sensor_state); + ADCSensorState next_sensor_state = adc_sensor_state < SensorsReady ? (ADCSensorState)(int(adc_sensor_state) + 1) : StartSampling; switch (adc_sensor_state) { - default: break; - case SensorsReady: { // All sensors have been read. Stay in this state for a few // ISRs to save on calls to temp update/checking code below. @@ -2934,72 +2824,128 @@ void Temperature::tick() { if (delay_count == 0) delay_count = extra_loops; // Init this delay if (--delay_count) // While delaying... next_sensor_state = SensorsReady; // retain this state (else, next state will be 0) - break; // No fallthru + break; } else { - adc_sensor_state = StartSampling; // Fall through to count up oversamples - next_sensor_state = NEXT_ENUM(StartSampling); // and possibly send the final readings. + adc_sensor_state = StartSampling; // Fall-through to start sampling + next_sensor_state = (ADCSensorState)(int(StartSampling) + 1); } } - // fallthru case StartSampling: // Start of sampling loops. Do updates/checks. - if (++temp_count >= OVERSAMPLENR) { // 10 * 16 * 1 / (16000000 / 64 / 256) = 164ms. + if (++temp_count >= OVERSAMPLENR) { // 10 * 16 * 1/(16000000/64/256) = 164ms. temp_count = 0; readings_ready(); } - adc_sensor_state = NEXT_ENUM(StartSampling); // Do one Prepare phase before exiting - next_sensor_state = NEXT_ENUM(adc_sensor_state); // Also update the next state - // fallthru + break; #if HAS_TEMP_ADC_0 - case PrepareTemp_0: HAL_START_ADC(TEMP_0_PIN); break; + case PrepareTemp_0: HAL_START_ADC(TEMP_0_PIN); break; + case MeasureTemp_0: ACCUMULATE_ADC(temp_hotend[0]); break; #endif + #if HAS_HEATED_BED - case PrepareTemp_BED: HAL_START_ADC(TEMP_BED_PIN); break; + case PrepareTemp_BED: HAL_START_ADC(TEMP_BED_PIN); break; + case MeasureTemp_BED: ACCUMULATE_ADC(temp_bed); break; #endif + #if HAS_TEMP_CHAMBER case PrepareTemp_CHAMBER: HAL_START_ADC(TEMP_CHAMBER_PIN); break; + case MeasureTemp_CHAMBER: ACCUMULATE_ADC(temp_chamber); break; #endif + #if HAS_TEMP_PROBE - case PrepareTemp_PROBE: HAL_START_ADC(TEMP_PROBE_PIN); break; + case PrepareTemp_PROBE: HAL_START_ADC(TEMP_PROBE_PIN); break; + case MeasureTemp_PROBE: ACCUMULATE_ADC(temp_probe); break; #endif + #if HAS_TEMP_ADC_1 - case PrepareTemp_1: HAL_START_ADC(TEMP_1_PIN); break; + case PrepareTemp_1: HAL_START_ADC(TEMP_1_PIN); break; + case MeasureTemp_1: ACCUMULATE_ADC(temp_hotend[1]); break; #endif + #if HAS_TEMP_ADC_2 - case PrepareTemp_2: HAL_START_ADC(TEMP_2_PIN); break; + case PrepareTemp_2: HAL_START_ADC(TEMP_2_PIN); break; + case MeasureTemp_2: ACCUMULATE_ADC(temp_hotend[2]); break; #endif + #if HAS_TEMP_ADC_3 - case PrepareTemp_3: HAL_START_ADC(TEMP_3_PIN); break; + case PrepareTemp_3: HAL_START_ADC(TEMP_3_PIN); break; + case MeasureTemp_3: ACCUMULATE_ADC(temp_hotend[3]); break; #endif + #if HAS_TEMP_ADC_4 - case PrepareTemp_4: HAL_START_ADC(TEMP_4_PIN); break; + case PrepareTemp_4: HAL_START_ADC(TEMP_4_PIN); break; + case MeasureTemp_4: ACCUMULATE_ADC(temp_hotend[4]); break; #endif + #if HAS_TEMP_ADC_5 - case PrepareTemp_5: HAL_START_ADC(TEMP_5_PIN); break; + case PrepareTemp_5: HAL_START_ADC(TEMP_5_PIN); break; + case MeasureTemp_5: ACCUMULATE_ADC(temp_hotend[5]); break; #endif + #if HAS_TEMP_ADC_6 - case PrepareTemp_6: HAL_START_ADC(TEMP_6_PIN); break; + case PrepareTemp_6: HAL_START_ADC(TEMP_6_PIN); break; + case MeasureTemp_6: ACCUMULATE_ADC(temp_hotend[6]); break; #endif + #if HAS_TEMP_ADC_7 - case PrepareTemp_7: HAL_START_ADC(TEMP_7_PIN); break; + case PrepareTemp_7: HAL_START_ADC(TEMP_7_PIN); break; + case MeasureTemp_7: ACCUMULATE_ADC(temp_hotend[7]); break; #endif + #if ENABLED(FILAMENT_WIDTH_SENSOR) - case Prepare_FILWIDTH: HAL_START_ADC(FILWIDTH_PIN); break; + case Prepare_FILWIDTH: HAL_START_ADC(FILWIDTH_PIN); break; + case Measure_FILWIDTH: + if (!HAL_ADC_READY()) + next_sensor_state = adc_sensor_state; // redo this state + else + filwidth.accumulate(HAL_READ_ADC()); + break; #endif + #if HAS_JOY_ADC_X - case PrepareJoy_X: HAL_START_ADC(JOY_X_PIN); break; + case PrepareJoy_X: HAL_START_ADC(JOY_X_PIN); break; + case MeasureJoy_X: ACCUMULATE_ADC(joystick.x); break; #endif + #if HAS_JOY_ADC_Y - case PrepareJoy_Y: HAL_START_ADC(JOY_Y_PIN); break; + case PrepareJoy_Y: HAL_START_ADC(JOY_Y_PIN); break; + case MeasureJoy_Y: ACCUMULATE_ADC(joystick.y); break; #endif + #if HAS_JOY_ADC_Z - case PrepareJoy_Z: HAL_START_ADC(JOY_Z_PIN); break; + case PrepareJoy_Z: HAL_START_ADC(JOY_Z_PIN); break; + case MeasureJoy_Z: ACCUMULATE_ADC(joystick.z); break; #endif + #if HAS_ADC_BUTTONS - case Prepare_ADC_KEY: HAL_START_ADC(ADC_KEYPAD_PIN); break; - #endif + #ifndef ADC_BUTTON_DEBOUNCE_DELAY + #define ADC_BUTTON_DEBOUNCE_DELAY 16 + #endif + case Prepare_ADC_KEY: HAL_START_ADC(ADC_KEYPAD_PIN); break; + case Measure_ADC_KEY: + if (!HAL_ADC_READY()) + next_sensor_state = adc_sensor_state; // redo this state + else if (ADCKey_count < ADC_BUTTON_DEBOUNCE_DELAY) { + raw_ADCKey_value = HAL_READ_ADC(); + if (raw_ADCKey_value <= 900UL * HAL_ADC_RANGE / 1024UL) { + NOMORE(current_ADCKey_raw, raw_ADCKey_value); + ADCKey_count++; + } + else { //ADC Key release + if (ADCKey_count > 0) ADCKey_count++; else ADCKey_pressed = false; + if (ADCKey_pressed) { + ADCKey_count = 0; + current_ADCKey_raw = HAL_ADC_RANGE; + } + } + } + if (ADCKey_count == ADC_BUTTON_DEBOUNCE_DELAY) ADCKey_pressed = true; + break; + #endif // HAS_ADC_BUTTONS + + case StartupDelay: break; } // switch(adc_sensor_state)