andrey
/
Marlin_FB4S
1
0
Fork 0
Code Issues Pull Requests Projects Releases Wiki Activity
Browse Source

lcd panel bed support 

advance and ultipanel not any more in default config
pull/1/head
Bernhard 13 years ago
parent
4bababf5b0
commit
415aadf704
6 changed files with 159 additions and 26 deletions
Whitespace
Show all changes Ignore whitespace when comparing lines Ignore changes in amount of whitespace Ignore changes in whitespace at EOL
Split View
Diff Options
Show Stats Download Patch File Download Diff File
  1. 9
      Marlin/Configuration.h
  2. 1
      Marlin/cardreader.pde
  3. 4
      Marlin/pins.h
  4. 48
      Marlin/temperature.cpp
  5. 30
      Marlin/temperature.h
  6. 93
      Marlin/ultralcd.pde

9
Marlin/Configuration.h
View File

@ -58,6 +58,10 @@
// Select one of these only to define how the bed temp is read.
//#define THERMISTORBED 1
//#define BED_USES_THERMISTOR
//#define BED_LIMIT_SWITCHING
#ifdef BED_LIMIT_SWITCHING
#define BED_HYSTERESIS 2 //only disable heating if T>target+BED_HYSTERESIS and enable heating if T>target-BED_HYSTERESIS
#endif
//#define BED_USES_AD595
#define BED_CHECK_INTERVAL 5000 //ms
@ -167,6 +171,7 @@
#define EXTRUDER_RUNOUT_SECONDS 30.
#define EXTRUDER_RUNOUT_ESTEPS 14. //mm filament
#define EXTRUDER_RUNOUT_SPEED 1500. //extrusion speed
#define EXTRUDER_RUNOUT_EXTRUDE 100
//===========================================================================
@ -296,7 +301,7 @@ const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of th
// hooke's law says: force = k * distance
// bernoulli's priniciple says: v ^ 2 / 2 + g . h + pressure / density = constant
// so: v ^ 2 is proportional to number of steps we advance the extruder
#define ADVANCE
//#define ADVANCE
#ifdef ADVANCE
#define EXTRUDER_ADVANCE_K .0
@ -315,7 +320,7 @@ const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of th
#define SD_FINISHED_STEPPERRELEASE true //if sd support and the file is finished: disable steppers?
#define SD_FINISHED_RELEASECOMMAND "M84 X Y E" // no z because of layer shift.
#define ULTIPANEL
//#define ULTIPANEL
#ifdef ULTIPANEL
//#define NEWPANEL //enable this if you have a click-encoder panel
#define SDSUPPORT

1
Marlin/cardreader.pde
View File

@ -432,6 +432,7 @@ void CardReader::updir()
void CardReader::printingHasFinished()
{
st_synchronize();
quickStop();
sdprinting = false;
stop_heating_wait=true;

4
Marlin/pins.h
View File

@ -555,7 +555,7 @@
#define Z_ENABLE_PIN 35
#define HEATER_BED_PIN 4
#define TEMP_BED_PIN 11
#define TEMP_BED_PIN 10
#define HEATER_0_PIN 2
#define TEMP_0_PIN 8
@ -734,4 +734,4 @@
HEATER_BED_PIN, FAN_PIN, \
_E0_PINS, _E1_PINS, _E2_PINS, \
TEMP_0_PIN, TEMP_1_PIN, TEMP_2_PIN, TEMP_BED_PIN }
#endif
#endif

48
Marlin/temperature.cpp
View File

@ -42,6 +42,10 @@
//===========================================================================
int target_raw[EXTRUDERS] = { 0 };
int target_raw_bed = 0;
#ifdef BED_LIMIT_SWITCHING
int target_bed_low_temp =0;
int target_bed_high_temp =0;
#endif
int current_raw[EXTRUDERS] = { 0 };
int current_raw_bed = 0;
@ -233,20 +237,39 @@ void manage_heater()
previous_millis_bed_heater = millis();
#if TEMP_BED_PIN > -1
// Check if temperature is within the correct range
if((current_raw_bed > bed_minttemp) && (current_raw_bed < bed_maxttemp)) {
if(current_raw_bed >= target_raw_bed)
{
#ifndef BED_LIMIT_SWITCHING
// Check if temperature is within the correct range
if((current_raw_bed > bed_minttemp) && (current_raw_bed < bed_maxttemp)) {
if(current_raw_bed >= target_raw_bed)
{
WRITE(HEATER_BED_PIN,LOW);
}
else
{
WRITE(HEATER_BED_PIN,HIGH);
}
}
else {
WRITE(HEATER_BED_PIN,LOW);
}
else
{
WRITE(HEATER_BED_PIN,HIGH);
#else //#ifdef BED_LIMIT_SWITCHING
// Check if temperature is within the correct band
if((current_raw_bed > bed_minttemp) && (current_raw_bed < bed_maxttemp)) {
if(current_raw_bed > target_bed_high_temp)
{
WRITE(HEATER_BED_PIN,LOW);
}
else
if(current_raw_bed <= target_bed_low_temp)
{
WRITE(HEATER_BED_PIN,HIGH);
}
}
}
else {
WRITE(HEATER_BED_PIN,LOW);
}
else {
WRITE(HEATER_BED_PIN,LOW);
}
#endif
#endif
}
@ -520,6 +543,9 @@ void setWatch()
void disable_heater()
{
for(int i=0;i<EXTRUDERS;i++)
setTargetHotend(0,i);
setTargetBed(0);
#if TEMP_0_PIN > -1
target_raw[0]=0;
soft_pwm[0]=0;

30
Marlin/temperature.h
View File

@ -43,6 +43,10 @@ extern int heatingtarget_raw[EXTRUDERS];
extern int current_raw[EXTRUDERS];
extern int target_raw_bed;
extern int current_raw_bed;
#ifdef BED_LIMIT_SWITCHING
extern int target_bed_low_temp ;
extern int target_bed_high_temp ;
#endif
extern float Kp,Ki,Kd,Kc;
#ifdef PIDTEMP
@ -83,7 +87,20 @@ FORCE_INLINE void setTargetHotend(const float &celsius, uint8_t extruder) {
};
FORCE_INLINE void setTargetBed(const float &celsius) {
target_raw_bed = temp2analogBed(celsius);
#ifdef BED_LIMIT_SWITCHING
if(celsius>BED_HYSTERESIS)
{
target_bed_low_temp= temp2analogBed(celsius-BED_HYSTERESIS);
target_bed_high_temp= temp2analogBed(celsius+BED_HYSTERESIS);
}
else
{
target_bed_low_temp=0;
target_bed_high_temp=0;
}
#endif
};
FORCE_INLINE bool isHeatingHotend(uint8_t extruder){
@ -125,6 +142,13 @@ FORCE_INLINE bool isCoolingBed() {
#error Invalid number of extruders
#endif
int getHeaterPower(int heater);
void disable_heater();
void setWatch();
void updatePID();
FORCE_INLINE void autotempShutdown(){
#ifdef AUTOTEMP
if(autotemp_enabled)
@ -135,11 +159,5 @@ FORCE_INLINE void autotempShutdown(){
}
#endif
}
int getHeaterPower(int heater);
void disable_heater();
void setWatch();
void updatePID();
#endif

93
Marlin/ultralcd.pde
View File

@ -165,8 +165,13 @@ void lcd_status()
//previous_millis_buttons=millis();
long ms=millis();
for(int8_t i=0; i<8; i++) {
#ifndef NEWPANEL
if((blocking[i]>ms))
buttons &= ~(1<<i);
#else
if((blocking>ms))
buttons &= ~(1<<i);
#endif
}
if((buttons==oldbuttons) && ((millis() - previous_millis_lcd) < LCD_UPDATE_INTERVAL) )
return;
@ -326,14 +331,14 @@ void MainMenu::showStatus()
int tBed=intround(degBed());
if((tBed!=oldtBed)||force_lcd_update)
{
lcd.setCursor(1,0);
lcd.setCursor(11,0);
lcd.print(ftostr3(tBed));
oldtBed=tBed;
}
int targetBed=intround(degTargetBed());
if((targetBed!=oldtargetBed)||force_lcd_update)
{
lcd.setCursor(5,0);
lcd.setCursor(15,0);
lcd.print(ftostr3(targetBed));
oldtargetBed=targetBed;
}
@ -352,11 +357,11 @@ void MainMenu::showStatus()
}
}
static int oldzpos=0;
int currentz=current_position[2]*10;
int currentz=current_position[2]*100;
if((currentz!=oldzpos)||force_lcd_update)
{
lcd.setCursor(10,1);
lcdprintPGM("Z:");lcd.print(itostr31(currentz));
lcdprintPGM("Z:");lcd.print(ftostr32(current_position[2]));
oldzpos=currentz;
}
static int oldfeedmultiply=0;
@ -490,7 +495,11 @@ void MainMenu::showPrepare()
updateActiveLines(ItemP_extrude,encoderpos);
}
enum {ItemT_exit,ItemT_speed,ItemT_flow,ItemT_nozzle,ItemT_fan};
enum {ItemT_exit,ItemT_speed,ItemT_flow,ItemT_nozzle,
#if (HEATER_BED_PIN > -1)
ItemT_bed,
#endif
ItemT_fan};
void MainMenu::showTune()
{
@ -572,6 +581,42 @@ void MainMenu::showTune()
lcd.setCursor(13,line);lcd.print(itostr3(encoderpos));
}
}break;
#if (HEATER_BED_PIN > -1)
case ItemT_bed:
{
if(force_lcd_update)
{
lcd.setCursor(0,line);lcdprintPGM(" \002Bed:");
lcd.setCursor(13,line);lcd.print(ftostr3(intround(degTargetBed())));
}
if((activeline!=line) )
break;
if(CLICKED)
{
linechanging=!linechanging;
if(linechanging)
{
encoderpos=intround(degTargetBed());
}
else
{
setTargetBed(encoderpos);
encoderpos=activeline*lcdslow;
beepshort();
}
BLOCK;
}
if(linechanging)
{
if(encoderpos<0) encoderpos=0;
if(encoderpos>260) encoderpos=260;
lcd.setCursor(13,line);lcd.print(itostr3(encoderpos));
}
}break;
#endif
case ItemT_fan:
{
@ -677,6 +722,9 @@ enum {
ItemCT_autotempactive,
ItemCT_autotempmin,ItemCT_autotempmax,ItemCT_autotempfact,
#endif
#if (HEATER_BED_PIN > -1)
ItemCT_bed,
#endif
ItemCT_fan,
ItemCT_PID_P,ItemCT_PID_I,ItemCT_PID_D,ItemCT_PID_C
};
@ -857,6 +905,41 @@ void MainMenu::showControlTemp()
}break;
#endif //autotemp
#if (HEATER_BED_PIN > -1)
case ItemCT_bed:
{
if(force_lcd_update)
{
lcd.setCursor(0,line);lcdprintPGM(" \002Bed:");
lcd.setCursor(13,line);lcd.print(ftostr3(intround(degTargetBed())));
}
if((activeline!=line) )
break;
if(CLICKED)
{
linechanging=!linechanging;
if(linechanging)
{
encoderpos=intround(degTargetBed());
}
else
{
setTargetBed(encoderpos);
encoderpos=activeline*lcdslow;
beepshort();
}
BLOCK;
}
if(linechanging)
{
if(encoderpos<0) encoderpos=0;
if(encoderpos>260) encoderpos=260;
lcd.setCursor(13,line);lcd.print(itostr3(encoderpos));
}
}break;
#endif
case ItemCT_fan:
{
if(force_lcd_update)

Write Preview
Loading…
Cancel
Save