diff --git a/Marlin/src/lcd/language/language_fr.h b/Marlin/src/lcd/language/language_fr.h index 7ea021cc0c..bd7b1114d8 100644 --- a/Marlin/src/lcd/language/language_fr.h +++ b/Marlin/src/lcd/language/language_fr.h @@ -36,9 +36,14 @@ #define MSG_YES _UxGT("Oui") #define MSG_NO _UxGT("Non") #define MSG_BACK _UxGT("Retour") +#define MSG_MEDIA_ABORTING _UxGT("Annulation...") #define MSG_MEDIA_INSERTED _UxGT("Média inséré") #define MSG_MEDIA_REMOVED _UxGT("Média retiré") #define MSG_MEDIA_RELEASED _UxGT("Média libéré") +#define MSG_MEDIA_WAITING _UxGT("Attente média") +#define MSG_MEDIA_READ_ERROR _UxGT("Err lecture média") +#define MSG_MEDIA_USB_REMOVED _UxGT("USB débranché") +#define MSG_MEDIA_USB_FAILED _UxGT("Erreur média USB") #define MSG_LCD_ENDSTOPS _UxGT("Butées") #define MSG_LCD_SOFT_ENDSTOPS _UxGT("Butées SW") #define MSG_MAIN _UxGT("Menu principal") @@ -89,6 +94,7 @@ #define MSG_LEVEL_BED _UxGT("Niveau du lit") #define MSG_LEVEL_CORNERS _UxGT("Niveau des coins") #define MSG_NEXT_CORNER _UxGT("Coin suivant") +#define MSG_MESH_EDITOR _UxGT("Edition Maillage") #define MSG_EDIT_MESH _UxGT("Modifier maille") #define MSG_EDITING_STOPPED _UxGT("Arrêt édit. maillage") #define MSG_PROBING_MESH _UxGT("Mesure point") @@ -110,6 +116,13 @@ #define MSG_X_OFFSET _UxGT("Buse 2 X") #define MSG_Y_OFFSET _UxGT("Buse 2 Y") #define MSG_Z_OFFSET _UxGT("Buse 2 Z") +#define MSG_G26_HEATING_BED _UxGT("G26 Chauffe lit") +#define MSG_G26_HEATING_NOZZLE _UxGT("G26 Chauffe buse") +#define MSG_G26_MANUAL_PRIME _UxGT("Amorce manuelle...") +#define MSG_G26_FIXED_LENGTH _UxGT("Amorce longueur fixe") +#define MSG_G26_PRIME_DONE _UxGT("Amorce terminée") +#define MSG_G26_CANCELED _UxGT("G26 annulé") +#define MSG_G26_LEAVING _UxGT("Sortie G26") #define MSG_UBL_DOING_G29 _UxGT("G29 en cours") #define MSG_UBL_UNHOMED _UxGT("Origine XYZ requise") #define MSG_UBL_TOOLS _UxGT("Outils UBL") @@ -169,6 +182,7 @@ #define MSG_UBL_NO_STORAGE _UxGT("Pas de mémoire") #define MSG_UBL_SAVE_ERROR _UxGT("Err: Enreg. UBL") #define MSG_UBL_RESTORE_ERROR _UxGT("Err: Ouvrir UBL") +#define MSG_UBL_Z_OFFSET _UxGT("Z-Offset: ") #define MSG_UBL_Z_OFFSET_STOPPED _UxGT("Décal. Z arrêté") #define MSG_UBL_STEP_BY_STEP_MENU _UxGT("UBL Pas à pas") @@ -432,6 +446,7 @@ #define MSG_DRIVE_STRENGTH _UxGT("Puiss. moteur ") #define MSG_DAC_PERCENT _UxGT("Driver %") #define MSG_DAC_EEPROM_WRITE _UxGT("DAC EEPROM sauv.") +#define MSG_ERROR_TMC _UxGT("ERREUR CONNEXION TMC") #define MSG_FILAMENT_CHANGE_HEADER_PAUSE _UxGT("IMPR. PAUSE") #define MSG_FILAMENT_CHANGE_HEADER_LOAD _UxGT("CHARGER FIL")