diff --git a/Marlin/example_configurations/delta/biv2.5/Configuration.h b/Marlin/example_configurations/delta/biv2.5/Configuration.h index 829d918a24..9a03e860c0 100644 --- a/Marlin/example_configurations/delta/biv2.5/Configuration.h +++ b/Marlin/example_configurations/delta/biv2.5/Configuration.h @@ -99,38 +99,6 @@ Here are some standard links for getting your machine calibrated: // Define this to have the electronics keep the power supply off on startup. If you don't know what this is leave it. // #define PS_DEFAULT_OFF - -//=========================================================================== -//============================== Delta Settings ============================= -//=========================================================================== -// Enable DELTA kinematics and most of the default configuration for Deltas -#define DELTA - -// Make delta curves from many straight lines (linear interpolation). -// This is a trade-off between visible corners (not enough segments) -// and processor overload (too many expensive sqrt calls). -#define DELTA_SEGMENTS_PER_SECOND 100 - -// NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them - -// Center-to-center distance of the holes in the diagonal push rods. -#define DELTA_DIAGONAL_ROD 440.0 // mm - -// Horizontal offset from middle of printer to smooth rod center. -#define DELTA_SMOOTH_ROD_OFFSET 330.0 // mm - -// Horizontal offset of the universal joints on the end effector. -#define DELTA_EFFECTOR_OFFSET 50.0 // mm - -// Horizontal offset of the universal joints on the carriages. -#define DELTA_CARRIAGE_OFFSET 20.0 // mm - -// Horizontal distance bridged by diagonal push rods when effector is centered. -#define DELTA_RADIUS (DELTA_SMOOTH_ROD_OFFSET-DELTA_EFFECTOR_OFFSET-DELTA_CARRIAGE_OFFSET) - -// Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers). -#define DELTA_PRINTABLE_RADIUS 160 - // @section temperature //=========================================================================== @@ -336,6 +304,41 @@ Here are some standard links for getting your machine calibrated: // Uncomment this option to enable CoreXY kinematics // #define COREXY +//=========================================================================== +//============================== Delta Settings ============================= +//=========================================================================== +// Enable DELTA kinematics and most of the default configuration for Deltas +#define DELTA + +#ifdef DELTA + +// Make delta curves from many straight lines (linear interpolation). +// This is a trade-off between visible corners (not enough segments) +// and processor overload (too many expensive sqrt calls). +#define DELTA_SEGMENTS_PER_SECOND 100 + +// NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them + +// Center-to-center distance of the holes in the diagonal push rods. +#define DELTA_DIAGONAL_ROD 440.0 // mm + +// Horizontal offset from middle of printer to smooth rod center. +#define DELTA_SMOOTH_ROD_OFFSET 330.0 // mm + +// Horizontal offset of the universal joints on the end effector. +#define DELTA_EFFECTOR_OFFSET 50.0 // mm + +// Horizontal offset of the universal joints on the carriages. +#define DELTA_CARRIAGE_OFFSET 20.0 // mm + +// Horizontal distance bridged by diagonal push rods when effector is centered. +#define DELTA_RADIUS (DELTA_SMOOTH_ROD_OFFSET-DELTA_EFFECTOR_OFFSET-DELTA_CARRIAGE_OFFSET) + +// Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers). +#define DELTA_PRINTABLE_RADIUS 160 + +#endif + // Enable this option for Toshiba steppers // #define CONFIG_STEPPERS_TOSHIBA diff --git a/Marlin/example_configurations/delta/generic/Configuration.h b/Marlin/example_configurations/delta/generic/Configuration.h index 205e400e4a..1c374514bb 100644 --- a/Marlin/example_configurations/delta/generic/Configuration.h +++ b/Marlin/example_configurations/delta/generic/Configuration.h @@ -99,38 +99,6 @@ Here are some standard links for getting your machine calibrated: // Define this to have the electronics keep the power supply off on startup. If you don't know what this is leave it. // #define PS_DEFAULT_OFF - -//=========================================================================== -//============================== Delta Settings ============================= -//=========================================================================== -// Enable DELTA kinematics and most of the default configuration for Deltas -#define DELTA - -// Make delta curves from many straight lines (linear interpolation). -// This is a trade-off between visible corners (not enough segments) -// and processor overload (too many expensive sqrt calls). -#define DELTA_SEGMENTS_PER_SECOND 200 - -// NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them - -// Center-to-center distance of the holes in the diagonal push rods. -#define DELTA_DIAGONAL_ROD 250.0 // mm - -// Horizontal offset from middle of printer to smooth rod center. -#define DELTA_SMOOTH_ROD_OFFSET 175.0 // mm - -// Horizontal offset of the universal joints on the end effector. -#define DELTA_EFFECTOR_OFFSET 33.0 // mm - -// Horizontal offset of the universal joints on the carriages. -#define DELTA_CARRIAGE_OFFSET 18.0 // mm - -// Horizontal distance bridged by diagonal push rods when effector is centered. -#define DELTA_RADIUS (DELTA_SMOOTH_ROD_OFFSET-DELTA_EFFECTOR_OFFSET-DELTA_CARRIAGE_OFFSET) - -// Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers). -#define DELTA_PRINTABLE_RADIUS 140 - // @section temperature //=========================================================================== @@ -336,6 +304,41 @@ Here are some standard links for getting your machine calibrated: // Uncomment this option to enable CoreXY kinematics // #define COREXY +//=========================================================================== +//============================== Delta Settings ============================= +//=========================================================================== +// Enable DELTA kinematics and most of the default configuration for Deltas +#define DELTA + +#ifdef DELTA + +// Make delta curves from many straight lines (linear interpolation). +// This is a trade-off between visible corners (not enough segments) +// and processor overload (too many expensive sqrt calls). +#define DELTA_SEGMENTS_PER_SECOND 200 + +// NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them + +// Center-to-center distance of the holes in the diagonal push rods. +#define DELTA_DIAGONAL_ROD 250.0 // mm + +// Horizontal offset from middle of printer to smooth rod center. +#define DELTA_SMOOTH_ROD_OFFSET 175.0 // mm + +// Horizontal offset of the universal joints on the end effector. +#define DELTA_EFFECTOR_OFFSET 33.0 // mm + +// Horizontal offset of the universal joints on the carriages. +#define DELTA_CARRIAGE_OFFSET 18.0 // mm + +// Horizontal distance bridged by diagonal push rods when effector is centered. +#define DELTA_RADIUS (DELTA_SMOOTH_ROD_OFFSET-DELTA_EFFECTOR_OFFSET-DELTA_CARRIAGE_OFFSET) + +// Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers). +#define DELTA_PRINTABLE_RADIUS 140 + +#endif + // Enable this option for Toshiba steppers // #define CONFIG_STEPPERS_TOSHIBA diff --git a/Marlin/example_configurations/delta/kossel_mini/Configuration.h b/Marlin/example_configurations/delta/kossel_mini/Configuration.h index 4399095c3c..4972d9ffdd 100644 --- a/Marlin/example_configurations/delta/kossel_mini/Configuration.h +++ b/Marlin/example_configurations/delta/kossel_mini/Configuration.h @@ -99,38 +99,6 @@ Here are some standard links for getting your machine calibrated: // Define this to have the electronics keep the power supply off on startup. If you don't know what this is leave it. // #define PS_DEFAULT_OFF - -//=========================================================================== -//============================== Delta Settings ============================= -//=========================================================================== -// Enable DELTA kinematics and most of the default configuration for Deltas -#define DELTA - -// Make delta curves from many straight lines (linear interpolation). -// This is a trade-off between visible corners (not enough segments) -// and processor overload (too many expensive sqrt calls). -#define DELTA_SEGMENTS_PER_SECOND 200 - -// NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them - -// Center-to-center distance of the holes in the diagonal push rods. -#define DELTA_DIAGONAL_ROD 215.0 // mm - -// Horizontal offset from middle of printer to smooth rod center. -#define DELTA_SMOOTH_ROD_OFFSET 145.0 // mm - -// Horizontal offset of the universal joints on the end effector. -#define DELTA_EFFECTOR_OFFSET 19.9 // mm - -// Horizontal offset of the universal joints on the carriages. -#define DELTA_CARRIAGE_OFFSET 19.5 // mm - -// Horizontal distance bridged by diagonal push rods when effector is centered. -#define DELTA_RADIUS (DELTA_SMOOTH_ROD_OFFSET-DELTA_EFFECTOR_OFFSET-DELTA_CARRIAGE_OFFSET) - -// Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers). -#define DELTA_PRINTABLE_RADIUS 90 - // @section temperature //=========================================================================== @@ -336,6 +304,41 @@ Here are some standard links for getting your machine calibrated: // Uncomment this option to enable CoreXY kinematics // #define COREXY +//=========================================================================== +//============================== Delta Settings ============================= +//=========================================================================== +// Enable DELTA kinematics and most of the default configuration for Deltas +#define DELTA + +#ifdef DELTA + +// Make delta curves from many straight lines (linear interpolation). +// This is a trade-off between visible corners (not enough segments) +// and processor overload (too many expensive sqrt calls). +#define DELTA_SEGMENTS_PER_SECOND 200 + +// NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them + +// Center-to-center distance of the holes in the diagonal push rods. +#define DELTA_DIAGONAL_ROD 215.0 // mm + +// Horizontal offset from middle of printer to smooth rod center. +#define DELTA_SMOOTH_ROD_OFFSET 145.0 // mm + +// Horizontal offset of the universal joints on the end effector. +#define DELTA_EFFECTOR_OFFSET 19.9 // mm + +// Horizontal offset of the universal joints on the carriages. +#define DELTA_CARRIAGE_OFFSET 19.5 // mm + +// Horizontal distance bridged by diagonal push rods when effector is centered. +#define DELTA_RADIUS (DELTA_SMOOTH_ROD_OFFSET-DELTA_EFFECTOR_OFFSET-DELTA_CARRIAGE_OFFSET) + +// Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers). +#define DELTA_PRINTABLE_RADIUS 90 + +#endif + // Enable this option for Toshiba steppers // #define CONFIG_STEPPERS_TOSHIBA