From 33752de12d8f1af6fa85bb0c689b618e37a56674 Mon Sep 17 00:00:00 2001 From: Scott Lahteine Date: Sat, 10 Feb 2018 19:39:32 -0600 Subject: [PATCH] Update some outdated configs --- .../examples/MakerParts/Configuration.h | 37 +- .../examples/stm32f103ret6/Configuration.h | 340 +++++++++++++----- 2 files changed, 266 insertions(+), 111 deletions(-) diff --git a/Marlin/src/config/examples/MakerParts/Configuration.h b/Marlin/src/config/examples/MakerParts/Configuration.h index 7b21cb3875..54c56a752e 100644 --- a/Marlin/src/config/examples/MakerParts/Configuration.h +++ b/Marlin/src/config/examples/MakerParts/Configuration.h @@ -126,6 +126,15 @@ */ #define SERIAL_PORT 0 +/** + * Select a secondary serial port on the board to use for communication with the host. + * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if avaialble. + * + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] + */ +#define SERIAL_PORT_2 -1 + /** * This setting determines the communication speed of the printer. * @@ -373,8 +382,9 @@ // Comment the following line to disable PID and enable bang-bang. #define PIDTEMP -#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current -#define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current +#define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current +#define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current +#define PID_K1 0.95 // Smoothing factor within any PID loop #if ENABLED(PIDTEMP) #define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result. //#define PID_DEBUG // Sends debug data to the serial port. @@ -384,7 +394,6 @@ // Set/get with gcode: M301 E[extruder number, 0-2] #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max. - #define K1 0.95 //smoothing factor within the PID // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it @@ -465,12 +474,13 @@ //=========================================================================== /** - * Thermal Protection protects your printer from damage and fire if a - * thermistor falls out or temperature sensors fail in any way. + * Thermal Protection provides additional protection to your printer from damage + * and fire. Marlin always includes safe min and max temperature ranges which + * protect against a broken or disconnected thermistor wire. * - * The issue: If a thermistor falls out or a temperature sensor fails, - * Marlin can no longer sense the actual temperature. Since a disconnected - * thermistor reads as a low temperature, the firmware will keep the heater on. + * The issue: If a thermistor falls out, it will report the much lower + * temperature of the air in the room, and the the firmware will keep + * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the * details can be tuned in Configuration_adv.h @@ -723,14 +733,16 @@ // X and Y axis travel speed (mm/m) between probes #define XY_PROBE_SPEED 8000 -// Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH) +// Speed for the first approach when double-probing (MULTIPLE_PROBING == 2) #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z // Speed for the "accurate" probe of each point #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2) -// Use double touch for probing -//#define PROBE_DOUBLE_TOUCH +// The number of probes to perform at each point. +// Set to 2 for a fast/slow probe, using the second probe result. +// Set to 3 or more for slow probes, averaging the results. +//#define MULTIPLE_PROBING 2 /** * Z probes require clearance when deploying, stowing, and moving between @@ -920,7 +932,8 @@ #define ENABLE_LEVELING_FADE_HEIGHT // For Cartesian machines, instead of dividing moves on mesh boundaries, - // split up moves into short segments like a Delta. + // split up moves into short segments like a Delta. This follows the + // contours of the bed more closely than edge-to-edge straight moves. #define SEGMENT_LEVELED_MOVES #define LEVELED_SEGMENT_LENGTH 5.0 // (mm) Length of all segments (except the last one) diff --git a/Marlin/src/config/examples/stm32f103ret6/Configuration.h b/Marlin/src/config/examples/stm32f103ret6/Configuration.h index ec6ed2799b..40e9a85a17 100644 --- a/Marlin/src/config/examples/stm32f103ret6/Configuration.h +++ b/Marlin/src/config/examples/stm32f103ret6/Configuration.h @@ -100,19 +100,29 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port 0 is always used by the Arduino bootloader regardless of this setting. + * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * - * :[0, 1, 2, 3, 4, 5, 6, 7] + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ #define SERIAL_PORT 0 +/** + * Select a secondary serial port on the board to use for communication with the host. + * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if avaialble. + * + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] + */ +#define SERIAL_PORT_2 -1 + /** * This setting determines the communication speed of the printer. * * 250000 works in most cases, but you might try a lower speed if * you commonly experience drop-outs during host printing. + * You may try up to 1000000 to speed up SD file transfer. * - * :[2400, 9600, 19200, 38400, 57600, 115200, 250000] + * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000] */ #define BAUDRATE 250000 @@ -139,6 +149,9 @@ // :[1, 2, 3, 4, 5] #define EXTRUDERS 1 +// Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc. +#define DEFAULT_NOMINAL_FILAMENT_DIA 3.0 + // For Cyclops or any "multi-extruder" that shares a single nozzle. //#define SINGLENOZZLE @@ -179,6 +192,21 @@ //#define HOTEND_OFFSET_Z { 0.0, 0.0 } #endif +/** + * Two separate X-carriages with extruders that connect to a moving part + * via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN. + */ +//#define PARKING_EXTRUDER +#if ENABLED(PARKING_EXTRUDER) + #define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage + #define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil + #define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined. + #define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders + #define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder + #define PARKING_EXTRUDER_SECURITY_RAISE 5 // Z-raise before parking + #define HOTEND_OFFSET_Z { 0.0, 1.3 } // Z-offsets of the two hotends. The first must be 0. +#endif + /** * "Mixing Extruder" * - Adds a new code, M165, to set the current mix factors. @@ -335,8 +363,9 @@ // Comment the following line to disable PID and enable bang-bang. #define PIDTEMP -#define BANG_MAX 180 // limits current to nozzle while in bang-bang mode; 255=full current -#define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current +#define BANG_MAX 180 // Limits current to nozzle while in bang-bang mode; 255=full current +#define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current +#define PID_K1 0.95 // Smoothing factor within any PID loop #if ENABLED(PIDTEMP) #define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result. //#define PID_DEBUG // Sends debug data to the serial port. @@ -346,7 +375,6 @@ // Set/get with gcode: M301 E[extruder number, 0-2] #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max. - #define K1 0.95 //smoothing factor within the PID // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it @@ -427,12 +455,13 @@ //=========================================================================== /** - * Thermal Protection protects your printer from damage and fire if a - * thermistor falls out or temperature sensors fail in any way. + * Thermal Protection provides additional protection to your printer from damage + * and fire. Marlin always includes safe min and max temperature ranges which + * protect against a broken or disconnected thermistor wire. * - * The issue: If a thermistor falls out or a temperature sensor fails, - * Marlin can no longer sense the actual temperature. Since a disconnected - * thermistor reads as a low temperature, the firmware will keep the heater on. + * The issue: If a thermistor falls out, it will report the much lower + * temperature of the air in the room, and the the firmware will keep + * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the * details can be tuned in Configuration_adv.h @@ -567,14 +596,13 @@ #define DEFAULT_ZJERK 0.3 #define DEFAULT_EJERK 5.0 - //=========================================================================== //============================= Z Probe Options ============================= //=========================================================================== // @section probes // -// See http://marlinfw.org/configuration/probes.html +// See http://marlinfw.org/docs/configuration/probes.html // /** @@ -609,7 +637,7 @@ * Probe Type * * Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc. - * You must activate one of these to use Auto Bed Leveling below. + * Activate one of these to use Auto Bed Leveling below. */ /** @@ -640,11 +668,11 @@ #endif /** - * Enable if probing seems unreliable. Heaters and/or fans - consistent with the - * options selected below - will be disabled during probing so as to minimize - * potential EM interference by quieting/silencing the source of the 'noise' (the change - * in current flowing through the wires). This is likely most useful to users of the - * BLTouch probe, but may also help those with inductive or other probe types. + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. */ //#define PROBING_HEATERS_OFF // Turn heaters off when probing //#define PROBING_FANS_OFF // Turn fans off when probing @@ -686,14 +714,16 @@ // X and Y axis travel speed (mm/m) between probes #define XY_PROBE_SPEED 8000 -// Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH) +// Speed for the first approach when double-probing (MULTIPLE_PROBING == 2) #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z // Speed for the "accurate" probe of each point #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2) -// Use double touch for probing -//#define PROBE_DOUBLE_TOUCH +// The number of probes to perform at each point. +// Set to 2 for a fast/slow probe, using the second probe result. +// Set to 3 or more for slow probes, averaging the results. +//#define MULTIPLE_PROBING 2 /** * Z probes require clearance when deploying, stowing, and moving between @@ -760,6 +790,8 @@ // @section homing +//#define NO_MOTION_BEFORE_HOMING // Inhibit movement until all axes have been homed + //#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ... // Be sure you have this distance over your Z_MAX_POS in case. @@ -783,10 +815,30 @@ #define Y_MAX_POS Y_BED_SIZE #define Z_MAX_POS 180 -// If enabled, axes won't move below MIN_POS in response to movement commands. +/** + * Software Endstops + * + * - Prevent moves outside the set machine bounds. + * - Individual axes can be disabled, if desired. + * - X and Y only apply to Cartesian robots. + * - Use 'M211' to set software endstops on/off or report current state + */ + +// Min software endstops constrain movement within minimum coordinate bounds #define MIN_SOFTWARE_ENDSTOPS -// If enabled, axes won't move above MAX_POS in response to movement commands. +#if ENABLED(MIN_SOFTWARE_ENDSTOPS) + #define MIN_SOFTWARE_ENDSTOP_X + #define MIN_SOFTWARE_ENDSTOP_Y + #define MIN_SOFTWARE_ENDSTOP_Z +#endif + +// Max software endstops constrain movement within maximum coordinate bounds #define MAX_SOFTWARE_ENDSTOPS +#if ENABLED(MAX_SOFTWARE_ENDSTOPS) + #define MAX_SOFTWARE_ENDSTOP_X + #define MAX_SOFTWARE_ENDSTOP_Y + #define MAX_SOFTWARE_ENDSTOP_Z +#endif /** * Filament Runout Sensor @@ -806,7 +858,7 @@ //=========================================================================== //=============================== Bed Leveling ============================== //=========================================================================== -// @section bedlevel +// @section calibrate /** * Choose one of the options below to enable G29 Bed Leveling. The parameters @@ -832,12 +884,7 @@ * - AUTO_BED_LEVELING_UBL (Unified Bed Leveling) * A comprehensive bed leveling system combining the features and benefits * of other systems. UBL also includes integrated Mesh Generation, Mesh - * Validation and Mesh Editing systems. Currently, UBL is only checked out - * for Cartesian Printers. That said, it was primarily designed to correct - * poor quality Delta Printers. If you feel adventurous and have a Delta, - * please post an issue if something doesn't work correctly. Initially, - * you will need to set a reduced bed size so you have a rectangular area - * to test on. + * Validation and Mesh Editing systems. * * - MESH_BED_LEVELING * Probe a grid manually @@ -864,6 +911,24 @@ // at which point movement will be level to the machine's XY plane. // The height can be set with M420 Z #define ENABLE_LEVELING_FADE_HEIGHT + + // For Cartesian machines, instead of dividing moves on mesh boundaries, + // split up moves into short segments like a Delta. This follows the + // contours of the bed more closely than edge-to-edge straight moves. + #define SEGMENT_LEVELED_MOVES + #define LEVELED_SEGMENT_LENGTH 5.0 // (mm) Length of all segments (except the last one) + + /** + * Enable the G26 Mesh Validation Pattern tool. + */ + //#define G26_MESH_VALIDATION + #if ENABLED(G26_MESH_VALIDATION) + #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle. + #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool. + #define MESH_TEST_HOTEND_TEMP 205.0 // (°C) Default nozzle temperature for the G26 Mesh Validation Tool. + #define MESH_TEST_BED_TEMP 60.0 // (°C) Default bed temperature for the G26 Mesh Validation Tool. + #endif + #endif #if ENABLED(AUTO_BED_LEVELING_LINEAR) || ENABLED(AUTO_BED_LEVELING_BILINEAR) @@ -919,7 +984,9 @@ //========================= Unified Bed Leveling ============================ //=========================================================================== - #define UBL_MESH_INSET 1 // Mesh inset margin on print area + //#define MESH_EDIT_GFX_OVERLAY // Display a graphics overlay while editing the mesh + + #define MESH_INSET 1 // Mesh inset margin on print area #define GRID_MAX_POINTS_X 10 // Don't use more than 15 points per axis, implementation limited. #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X @@ -930,8 +997,8 @@ #define UBL_PROBE_PT_3_X 180 #define UBL_PROBE_PT_3_Y 20 - #define UBL_G26_MESH_VALIDATION // Enable G26 mesh validation #define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle + #define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500 #elif ENABLED(MESH_BED_LEVELING) @@ -958,6 +1025,9 @@ #define LCD_PROBE_Z_RANGE 4 // Z Range centered on Z_MIN_POS for LCD Z adjustment #endif +// Add a menu item to move between bed corners for manual bed adjustment +//#define LEVEL_BED_CORNERS + /** * Commands to execute at the end of G29 probing. * Useful to retract or move the Z probe out of the way. @@ -988,14 +1058,71 @@ //#define Z_SAFE_HOMING #if ENABLED(Z_SAFE_HOMING) - #define Z_SAFE_HOMING_X_POINT ((X_BED_SIZE) / 2) // X point for Z homing when homing all axis (G28). - #define Z_SAFE_HOMING_Y_POINT ((Y_BED_SIZE) / 2) // Y point for Z homing when homing all axis (G28). + #define Z_SAFE_HOMING_X_POINT ((X_BED_SIZE) / 2) // X point for Z homing when homing all axes (G28). + #define Z_SAFE_HOMING_Y_POINT ((Y_BED_SIZE) / 2) // Y point for Z homing when homing all axes (G28). #endif // Homing speeds (mm/m) #define HOMING_FEEDRATE_XY (50*60) #define HOMING_FEEDRATE_Z (4*60) +// @section calibrate + +/** + * Bed Skew Compensation + * + * This feature corrects for misalignment in the XYZ axes. + * + * Take the following steps to get the bed skew in the XY plane: + * 1. Print a test square (e.g., https://www.thingiverse.com/thing:2563185) + * 2. For XY_DIAG_AC measure the diagonal A to C + * 3. For XY_DIAG_BD measure the diagonal B to D + * 4. For XY_SIDE_AD measure the edge A to D + * + * Marlin automatically computes skew factors from these measurements. + * Skew factors may also be computed and set manually: + * + * - Compute AB : SQRT(2*AC*AC+2*BD*BD-4*AD*AD)/2 + * - XY_SKEW_FACTOR : TAN(PI/2-ACOS((AC*AC-AB*AB-AD*AD)/(2*AB*AD))) + * + * If desired, follow the same procedure for XZ and YZ. + * Use these diagrams for reference: + * + * Y Z Z + * ^ B-------C ^ B-------C ^ B-------C + * | / / | / / | / / + * | / / | / / | / / + * | A-------D | A-------D | A-------D + * +-------------->X +-------------->X +-------------->Y + * XY_SKEW_FACTOR XZ_SKEW_FACTOR YZ_SKEW_FACTOR + */ +//#define SKEW_CORRECTION + +#if ENABLED(SKEW_CORRECTION) + // Input all length measurements here: + #define XY_DIAG_AC 282.8427124746 + #define XY_DIAG_BD 282.8427124746 + #define XY_SIDE_AD 200 + + // Or, set the default skew factors directly here + // to override the above measurements: + #define XY_SKEW_FACTOR 0.0 + + //#define SKEW_CORRECTION_FOR_Z + #if ENABLED(SKEW_CORRECTION_FOR_Z) + #define XZ_DIAG_AC 282.8427124746 + #define XZ_DIAG_BD 282.8427124746 + #define YZ_DIAG_AC 282.8427124746 + #define YZ_DIAG_BD 282.8427124746 + #define YZ_SIDE_AD 200 + #define XZ_SKEW_FACTOR 0.0 + #define YZ_SKEW_FACTOR 0.0 + #endif + + // Enable this option for M852 to set skew at runtime + //#define SKEW_CORRECTION_GCODE +#endif + //============================================================================= //============================= Additional Features =========================== //============================================================================= @@ -1174,11 +1301,11 @@ * * Select the language to display on the LCD. These languages are available: * - * en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, eu, fi, fr, gl, hr, - * it, kana, kana_utf8, nl, pl, pt, pt_utf8, pt-br, pt-br_utf8, ru, tr, uk, - * zh_CN, zh_TW, test + * en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, eu, fi, fr, fr_utf8, gl, + * hr, it, kana, kana_utf8, nl, pl, pt, pt_utf8, pt-br, pt-br_utf8, ru, sk_utf8, + * tr, uk, zh_CN, zh_TW, test * - * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', test':'TEST' } + * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', test':'TEST' } */ #define LCD_LANGUAGE en @@ -1200,7 +1327,7 @@ * - Click the controller to view the LCD menu * - The LCD will display Japanese, Western, or Cyrillic text * - * See https://github.com/MarlinFirmware/Marlin/wiki/LCD-Language + * See http://marlinfw.org/docs/development/lcd_language.html * * :['JAPANESE', 'WESTERN', 'CYRILLIC'] */ @@ -1332,12 +1459,6 @@ // //#define ULTIPANEL -// -// Cartesio UI -// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface -// -//#define CARTESIO_UI - // // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3) // http://reprap.org/wiki/PanelOne @@ -1420,6 +1541,12 @@ // //#define BQ_LCD_SMART_CONTROLLER +// +// Cartesio UI +// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface +// +//#define CARTESIO_UI + // // ANET and Tronxy Controller supported displays. // @@ -1520,6 +1647,47 @@ // //#define OLED_PANEL_TINYBOY2 +// +// Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller +// https://www.aliexpress.com/item/Micromake-Makeboard-3D-Printer-Parts-3D-Printer-Mini-Display-1602-Mini-Controller-Compatible-with-Ramps-1/32765887917.html +// +//#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602 + +// +// MKS MINI12864 with graphic controller and SD support +// http://reprap.org/wiki/MKS_MINI_12864 +// +//#define MKS_MINI_12864 + +// +// Factory display for Creality CR-10 +// https://www.aliexpress.com/item/Universal-LCD-12864-3D-Printer-Display-Screen-With-Encoder-For-CR-10-CR-7-Model/32833148327.html +// +// This is RAMPS-compatible using a single 10-pin connector. +// (For CR-10 owners who want to replace the Melzi Creality board but retain the display) +// +//#define CR10_STOCKDISPLAY + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// AZSMZ 12864 LCD with SD +// https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html +// +//#define AZSMZ_12864 + +// Silvergate GLCD controller +// http://github.com/android444/Silvergate +// +//#define SILVER_GATE_GLCD_CONTROLLER + //============================================================================= //=============================== Extra Features ============================== //============================================================================= @@ -1576,16 +1744,22 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. + * For Neopixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOFSET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! + * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * + * LED Type. Enable only one of the following two options. + * */ //#define RGB_LED //#define RGBW_LED + #if ENABLED(RGB_LED) || ENABLED(RGBW_LED) #define RGB_LED_R_PIN 34 #define RGB_LED_G_PIN 43 @@ -1594,11 +1768,14 @@ #endif // Support for Adafruit Neopixel LED driver -//#define NEOPIXEL_RGBW_LED -#if ENABLED(NEOPIXEL_RGBW_LED) - #define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard) - #define NEOPIXEL_PIXELS 3 - //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup +//#define NEOPIXEL_LED +#if ENABLED(NEOPIXEL_LED) + #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) + #define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba) + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. + #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) + //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup #endif /** @@ -1612,67 +1789,32 @@ * - Change to green once print has finished * - Turn off after the print has finished and the user has pushed a button */ -#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED) +#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED) #define PRINTER_EVENT_LEDS #endif -/*********************************************************************\ -* R/C SERVO support -* Sponsored by TrinityLabs, Reworked by codexmas -**********************************************************************/ +/** + * R/C SERVO support + * Sponsored by TrinityLabs, Reworked by codexmas + */ -// Number of servos -// -// If you select a configuration below, this will receive a default value and does not need to be set manually -// set it manually if you have more servos than extruders and wish to manually control some -// leaving it undefined or defining as 0 will disable the servo subsystem -// If unsure, leave commented / disabled -// +/** + * Number of servos + * + * For some servo-related options NUM_SERVOS will be set automatically. + * Set this manually if there are extra servos needing manual control. + * Leave undefined or set to 0 to entirely disable the servo subsystem. + */ //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command // Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle. // 300ms is a good value but you can try less delay. // If the servo can't reach the requested position, increase it. -#define SERVO_DELAY 300 +#define SERVO_DELAY { 300 } // Servo deactivation // // With this option servos are powered only during movement, then turned off to prevent jitter. //#define DEACTIVATE_SERVOS_AFTER_MOVE -/** - * Filament Width Sensor - * - * Measures the filament width in real-time and adjusts - * flow rate to compensate for any irregularities. - * - * Also allows the measured filament diameter to set the - * extrusion rate, so the slicer only has to specify the - * volume. - * - * Only a single extruder is supported at this time. - * - * 34 RAMPS_14 : Analog input 5 on the AUX2 connector - * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) - * 301 RAMBO : Analog input 3 - * - * Note: May require analog pins to be defined for other boards. - */ -//#define FILAMENT_WIDTH_SENSOR - -#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading. - -#if ENABLED(FILAMENT_WIDTH_SENSOR) - #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3) - #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber - - #define FILWIDTH_ERROR_MARGIN 1.0 // (mm) If a measurement differs too much from nominal width ignore it - #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. - - #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially - - // Display filament width on the LCD status line. Status messages will expire after 5 seconds. - //#define FILAMENT_LCD_DISPLAY -#endif - #endif // CONFIGURATION_H