Adjust park position description

Marlin/Configuration.h

@@ -1413,7 +1413,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

Marlin/Configuration_adv.h

@@ -1002,7 +1002,7 @@
   #if ENABLED(DOUBLECLICK_FOR_Z_BABYSTEPPING)
     #define DOUBLECLICK_MAX_INTERVAL 1250   // Maximum interval between clicks, in milliseconds.
                                             // Note: Extra time may be added to mitigate controller latency.
-    //#define BABYSTEP_ALWAYS_AVAILABLE     // Allow babystepping at all times (not just during movement).
+    #define BABYSTEP_ALWAYS_AVAILABLE     // Allow babystepping at all times (not just during movement).
     //#define MOVE_Z_WHEN_IDLE              // Jump to the move Z menu on doubleclick when printer is idle.
     #if ENABLED(MOVE_Z_WHEN_IDLE)
       #define MOVE_Z_IDLE_MULTIPLICATOR 1   // Multiply 1mm by this factor for the move step size.

config/default/Configuration.h

@@ -1413,7 +1413,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/3DFabXYZ/Migbot/Configuration.h

@@ -1444,7 +1444,7 @@
 #define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/AlephObjects/TAZ4/Configuration.h

@@ -1433,7 +1433,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/AliExpress/CL-260/Configuration.h

@@ -1413,7 +1413,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/AliExpress/UM2pExt/Configuration.h

@@ -1424,7 +1424,7 @@
 #define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/Anet/A2/Configuration.h

@@ -1413,7 +1413,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/Anet/A2plus/Configuration.h

@@ -1413,7 +1413,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/Anet/A6/Configuration.h

@@ -1565,7 +1565,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/Anet/A8/Configuration.h

@@ -1426,7 +1426,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/AnyCubic/i3/Configuration.h

@@ -1423,7 +1423,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/ArmEd/Configuration.h

@@ -1414,7 +1414,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/Azteeg/X5GT/Configuration.h

@@ -1413,7 +1413,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/BIBO/TouchX/cyclops/Configuration.h

@@ -1413,7 +1413,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/BIBO/TouchX/default/Configuration.h

@@ -1413,7 +1413,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/BQ/Hephestos/Configuration.h

@@ -1401,7 +1401,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/BQ/Hephestos_2/Configuration.h

@@ -1413,7 +1413,7 @@
 #define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 10 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/BQ/WITBOX/Configuration.h

@@ -1401,7 +1401,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/Cartesio/Configuration.h

@@ -1412,7 +1412,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/Creality/CR-10/Configuration.h

@@ -1423,7 +1423,7 @@
 #define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/Creality/CR-10S/Configuration.h

@@ -1414,7 +1414,7 @@
 #define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 3), (Y_MAX_POS - 3), 10 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/Creality/CR-10_5S/Configuration.h

@@ -1416,7 +1416,7 @@
 #define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 20), (Y_MAX_POS - 20), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/Creality/CR-10mini/Configuration.h

@@ -1432,7 +1432,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/Creality/CR-8/Configuration.h

@@ -1423,7 +1423,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/Creality/Ender-2/Configuration.h

@@ -1417,7 +1417,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/Creality/Ender-3/Configuration.h

@@ -1417,7 +1417,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/Creality/Ender-4/Configuration.h

@@ -1423,7 +1423,7 @@
 #define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/Einstart-S/Configuration.h

@@ -1423,7 +1423,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/Felix/Configuration.h

@@ -1395,7 +1395,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/Felix/DUAL/Configuration.h

@@ -1395,7 +1395,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/FlashForge/CreatorPro/Configuration.h

@@ -1404,7 +1404,7 @@
 #define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MAX_POS - 2), (Y_MAX_POS - 2), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/FolgerTech/i3-2020/Configuration.h

@@ -1419,7 +1419,7 @@
 #define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/Formbot/Raptor/Configuration.h

@@ -1518,7 +1518,7 @@
 #define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { 10, 10, 20}
   #define NOZZLE_PARK_XY_FEEDRATE 70    // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/Formbot/T_Rex_2+/Configuration.h

@@ -1448,7 +1448,7 @@
 #define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { 50, (Y_MIN_POS + 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/Formbot/T_Rex_3/Configuration.h

@@ -1438,7 +1438,7 @@
 #define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { 100, (Y_MIN_POS + 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/Geeetech/A10M/Configuration.h

@@ -1398,7 +1398,7 @@
 #define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { 3, 3, 10 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/Geeetech/A20M/Configuration.h

@@ -1398,7 +1398,7 @@
 #define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { 3, 3, 10 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/Geeetech/GT2560/Configuration.h

@@ -1428,7 +1428,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h

@@ -1402,7 +1402,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/Geeetech/MeCreator2/Configuration.h

@@ -1420,7 +1420,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h

@@ -1429,7 +1429,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h

@@ -1428,7 +1428,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/Geeetech/Prusa i3 Pro C/Configuration.h

@@ -1413,7 +1413,7 @@
 #define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/Geeetech/Prusa i3 Pro W/Configuration.h

@@ -1413,7 +1413,7 @@
 #define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/Infitary/i3-M508/Configuration.h

@@ -1417,7 +1417,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/JGAurora/A5/Configuration.h

@@ -1425,7 +1425,7 @@
 #define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/MakerParts/Configuration.h

@@ -1433,7 +1433,7 @@
 #define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/Malyan/M150/Configuration.h

@@ -1441,7 +1441,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/Malyan/M200/Configuration.h

@@ -1412,7 +1412,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/Micromake/C1/basic/Configuration.h

@@ -1417,7 +1417,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/Micromake/C1/enhanced/Configuration.h

@@ -1417,7 +1417,7 @@
 #define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/Mks/Robin/Configuration.h

@@ -1414,7 +1414,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/Mks/Sbase/Configuration.h

@@ -1413,7 +1413,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/Printrbot/PrintrboardG2/Configuration.h

@@ -1421,7 +1421,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/RapideLite/RL200/Configuration.h

@@ -1413,7 +1413,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/RepRapPro/Huxley/Configuration.h

@@ -1462,7 +1462,7 @@ Black rubber belt(MXL), 18 - tooth aluminium pulley : 87.489 step per mm (Huxley
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100                        // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE DEFAULT_MAX_Z_FEEDRATE      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/RepRapWorld/Megatronics/Configuration.h

@@ -1413,7 +1413,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/RigidBot/Configuration.h

@@ -1411,7 +1411,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/SCARA/Configuration.h

@@ -1426,7 +1426,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/STM32/Black_STM32F407VET6/Configuration.h

@@ -1413,7 +1413,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/STM32/STM32F10/Configuration.h

@@ -1415,7 +1415,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/STM32/stm32f103ret6/Configuration.h

@@ -1415,7 +1415,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/Sanguinololu/Configuration.h

@@ -1444,7 +1444,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/TheBorg/Configuration.h

@@ -1413,7 +1413,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/TinyBoy2/Configuration.h

@@ -1469,7 +1469,7 @@
 #define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/Tronxy/X1/Configuration.h

@@ -1413,7 +1413,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/Tronxy/X3A/Configuration.h

@@ -1417,7 +1417,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/Tronxy/X5S-2E/Configuration.h

@@ -1434,7 +1434,7 @@
 #define NOZZLE_PARK_FEATURE P2
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/Tronxy/X5S/Configuration.h

@@ -1412,7 +1412,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/Tronxy/XY100/Configuration.h

@@ -1424,7 +1424,7 @@
 #define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/UltiMachine/Archim1/Configuration.h

@@ -1413,7 +1413,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/UltiMachine/Archim2/Configuration.h

@@ -1413,7 +1413,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/VORONDesign/Configuration.h

@@ -1422,7 +1422,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/Velleman/K8200/Configuration.h

@@ -1443,7 +1443,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/Velleman/K8400/Configuration.h

@@ -1413,7 +1413,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/Velleman/K8400/Dual-head/Configuration.h

@@ -1413,7 +1413,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/WASP/PowerWASP/Configuration.h

@@ -1432,7 +1432,7 @@
 #define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 190 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 10     // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/Wanhao/Duplicator 6/Configuration.h

@@ -1423,7 +1423,7 @@
 #define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/adafruit/ST7565/Configuration.h

@@ -1413,7 +1413,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/delta/Anycubic/Kossel/Configuration.h

@@ -1603,7 +1603,7 @@
 #define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { 0, 0, 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 100    // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/delta/FLSUN/auto_calibrate/Configuration.h

@@ -1541,7 +1541,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), 0, 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/delta/FLSUN/kossel/Configuration.h

@@ -1540,7 +1540,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), 0, 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/delta/FLSUN/kossel_mini/Configuration.h

@@ -1540,7 +1540,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), 0, 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/delta/Geeetech/Rostock 301/Configuration.h

@@ -1531,7 +1531,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), 0, 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/delta/Hatchbox_Alpha/Configuration.h

@@ -1543,7 +1543,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), 0, 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/delta/MKS/SBASE/Configuration.h

@@ -1528,7 +1528,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/delta/Tevo Little Monster/Configuration.h

@@ -1521,7 +1521,7 @@
 #define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { 0, 0, (DELTA_HEIGHT - 10) }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/delta/generic/Configuration.h

@@ -1528,7 +1528,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), 0, 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/delta/kossel_mini/Configuration.h

@@ -1530,7 +1530,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), 0, 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/delta/kossel_pro/Configuration.h

@@ -1531,7 +1531,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), 0, 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/delta/kossel_xl/Configuration.h

@@ -1531,7 +1531,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), 0, 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/gCreate/gMax1.5+/Configuration.h

@@ -1416,7 +1416,7 @@
 #define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/makibox/Configuration.h

@@ -1416,7 +1416,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/stm32/STM32F4/Configuration.h

@@ -1413,7 +1413,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/tvrrug/Round2/Configuration.h

@@ -1408,7 +1408,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)

config/examples/wt150/Configuration.h

@@ -1418,7 +1418,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)