whitespace

Marlin/Configuration_adv.h

@@ -47,7 +47,7 @@
  * is reported.  This allows us to ignore intermittent error conditions while
  * still detecting an actual failure, which should result in a continuous
  * stream of errors from the sensor.
- * 
+ *
  * Set this value to 0 to fail on the first error to occur.
  */
 #define THERMOCOUPLE_MAX_ERRORS 15

Marlin/src/feature/direct_stepping.cpp

@@ -61,7 +61,7 @@ namespace DirectStepping {
 
   template<typename Cfg>
   uint8_t SerialPageManager<Cfg>::pages[Cfg::NUM_PAGES][Cfg::PAGE_SIZE];
-          
+
   template<typename Cfg>
   uint8_t SerialPageManager<Cfg>::checksum;
 

Marlin/src/module/temperature.cpp

@@ -2075,7 +2075,7 @@ void Temperature::disable_all_heaters() {
       // Needed to return the correct temp when this is called too soon
       static uint16_t max6675_temp_previous[COUNT_6675] = { 0 };
     #endif
-    
+
     static uint8_t max6675_errors[COUNT_6675] = { 0 };
 
     #define MAX6675_HEAT_INTERVAL 250UL

Marlin/src/pins/ramps/pins_RAMPS_CREALITY.h

@@ -47,7 +47,6 @@
   #define PS_ON_PIN                           40  // Used by CR2020 Industrial series
 #endif
 
-
 #if ENABLED(CASE_LIGHT_ENABLE) && !defined(CASE_LIGHT_PIN)
   #define CASE_LIGHT_PIN                      65
 #endif
@@ -65,5 +64,5 @@
 
 #define SUICIDE_PIN                           12  // Used by CR2020 Industrial series
 #ifndef SUICIDE_PIN_INVERTING
-  #define SUICIDE_PIN_INVERTING             true
+  #define SUICIDE_PIN_INVERTING true
 #endif

Marlin/src/pins/ramps/pins_TRIGORILLA_14.h

@@ -59,7 +59,7 @@
 
 #define RAMPS_D10_PIN            TG_HEATER_0_PIN  // HEATER_0_PIN is always RAMPS_D10_PIN in pins_RAMPS.h
 
-#if HAS_MULTI_HOTEND                                   // EEF and EEB
+#if HAS_MULTI_HOTEND                              // EEF and EEB
   #define RAMPS_D9_PIN           TG_HEATER_1_PIN
   #if !TEMP_SENSOR_BED
     // EEF
@@ -79,7 +79,7 @@
   #define RAMPS_D8_PIN               TG_FAN0_PIN
 #endif
 
-#if HAS_MULTI_HOTEND || TEMP_SENSOR_BED                // EEF, EEB, EFB
+#if HAS_MULTI_HOTEND || TEMP_SENSOR_BED           // EEF, EEB, EFB
   #define FAN1_PIN                   TG_FAN1_PIN
 #endif
 #define FAN2_PIN                     TG_FAN2_PIN

Marlin/src/pins/stm32f4/pins_BTT_SKR_PRO_V1_1.h

@@ -352,8 +352,8 @@
  *           ￣￣
  *            W1
  */
-#define ESP_WIFI_MODULE_COM 6                         // Must also set either SERIAL_PORT or SERIAL_PORT_2 to this
+#define ESP_WIFI_MODULE_COM 6                     // Must also set either SERIAL_PORT or SERIAL_PORT_2 to this
-#define ESP_WIFI_MODULE_BAUDRATE            BAUDRATE  // Must use same BAUDRATE as SERIAL_PORT & SERIAL_PORT_2
+#define ESP_WIFI_MODULE_BAUDRATE        BAUDRATE  // Must use same BAUDRATE as SERIAL_PORT & SERIAL_PORT_2
 #define ESP_WIFI_MODULE_RESET_PIN           PG0
 #define ESP_WIFI_MODULE_ENABLE_PIN          PG1
 #define ESP_WIFI_MODULE_GPIO0_PIN           PF14