From 2f1b89bd1f4ae88e9b1b9e62ea567ac3a4d1178a Mon Sep 17 00:00:00 2001 From: Stephen Hawes Date: Sat, 3 Sep 2022 21:55:37 -0400 Subject: [PATCH] =?UTF-8?q?=E2=9C=A8=20Opulo=20LumenPnP=20REV04=20(#24718)?= MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit --- Marlin/src/core/boards.h | 1 + Marlin/src/pins/pins.h | 2 + .../src/pins/stm32f4/pins_OPULO_LUMEN_REV4.h | 206 ++++++++++++++++++ .../boards/marlin_opulo_lumen_rev4.json | 51 +++++ ini/stm32f4.ini | 11 + 5 files changed, 271 insertions(+) create mode 100644 Marlin/src/pins/stm32f4/pins_OPULO_LUMEN_REV4.h create mode 100644 buildroot/share/PlatformIO/boards/marlin_opulo_lumen_rev4.json diff --git a/Marlin/src/core/boards.h b/Marlin/src/core/boards.h index 4e3227ba58..272a82f3b7 100644 --- a/Marlin/src/core/boards.h +++ b/Marlin/src/core/boards.h @@ -421,6 +421,7 @@ #define BOARD_ARTILLERY_RUBY 4238 // Artillery Ruby (STM32F401RC) #define BOARD_FYSETC_SPIDER_V2_2 4239 // FYSETC Spider V2.2 (STM32F446VE) #define BOARD_CREALITY_V24S1_301F4 4240 // Creality v2.4.S1_301F4 (STM32F401RC) as found in the Ender-3 S1 F4 +#define BOARD_OPULO_LUMEN_REV4 4241 // Opulo Lumen PnP Controller REV4 (STM32F407VE / STM32F407VG) // // ARM Cortex M7 diff --git a/Marlin/src/pins/pins.h b/Marlin/src/pins/pins.h index 14d16c5415..e2f6ea2924 100644 --- a/Marlin/src/pins/pins.h +++ b/Marlin/src/pins/pins.h @@ -701,6 +701,8 @@ #include "stm32f4/pins_ARTILLERY_RUBY.h" // STM32F4 env:Artillery_Ruby #elif MB(CREALITY_V24S1_301F4) #include "stm32f4/pins_CREALITY_V24S1_301F4.h" // STM32F4 env:STM32F401RC_creality env:STM32F401RC_creality_jlink env:STM32F401RC_creality_stlink +#elif MB(OPULO_LUMEN_REV4) + #include "stm32f4/pins_OPULO_LUMEN_REV4.h" // STM32F4 env:Opulo_Lumen_REV4 // // ARM Cortex M7 diff --git a/Marlin/src/pins/stm32f4/pins_OPULO_LUMEN_REV4.h b/Marlin/src/pins/stm32f4/pins_OPULO_LUMEN_REV4.h new file mode 100644 index 0000000000..d16d7b200b --- /dev/null +++ b/Marlin/src/pins/stm32f4/pins_OPULO_LUMEN_REV4.h @@ -0,0 +1,206 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2022 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +/** + * STM32F407VET6 on Opulo Lumen PnP Rev3 + * Website - https://opulo.io/ + */ + +#define ALLOW_STM32DUINO +#include "env_validate.h" + +#define BOARD_INFO_NAME "LumenPnP Motherboard REV04" +#define DEFAULT_MACHINE_NAME "LumenPnP" + +/** + * By default, the extra stepper motor configuration is: + * I = Left Head + * J = Right Head + * K = Auxiliary (Conveyor belt) + */ + +#define SRAM_EEPROM_EMULATION +#define MARLIN_EEPROM_SIZE 0x2000 // 8K + +// I2C MCP3426 (16-Bit, 240SPS, dual-channel ADC) +#define HAS_MCP3426_ADC + +// +// Servos +// +#define SERVO0_PIN PB10 +#define SERVO1_PIN PB11 + +// +// Limit Switches +// +#define X_STOP_PIN PC6 +#define Y_STOP_PIN PD15 +#define Z_STOP_PIN PD14 + +// None of these require limit switches by default, so we leave these commented +// here for your reference. +//#define I_MIN_PIN PA8 +//#define I_MAX_PIN PA8 +//#define J_MIN_PIN PD13 +//#define J_MAX_PIN PD13 +//#define K_MIN_PIN PC9 +//#define K_MAX_PIN PC9 + +// +// Steppers +// +#define X_STEP_PIN PB15 +#define X_DIR_PIN PB14 +#define X_ENABLE_PIN PD9 + +#define Y_STEP_PIN PE15 +#define Y_DIR_PIN PE14 +#define Y_ENABLE_PIN PB13 + +#define Z_STEP_PIN PE7 +#define Z_DIR_PIN PB1 +#define Z_ENABLE_PIN PE9 + +#define I_STEP_PIN PC4 +#define I_DIR_PIN PA4 +#define I_ENABLE_PIN PB0 + +#define J_STEP_PIN PE11 +#define J_DIR_PIN PE10 +#define J_ENABLE_PIN PE13 + +#define K_STEP_PIN PD6 +#define K_DIR_PIN PD7 +#define K_ENABLE_PIN PA3 + +#if HAS_TMC_SPI + /** + * Make sure to configure the jumpers on the back side of the Mobo according to + * this diagram: https://github.com/MarlinFirmware/Marlin/pull/23851 + */ + #error "SPI drivers require a custom jumper configuration, see comment above! Comment out this line to continue." + + #if AXIS_HAS_SPI(X) + #define X_CS_PIN PD8 + #endif + #if AXIS_HAS_SPI(Y) + #define Y_CS_PIN PB12 + #endif + #if AXIS_HAS_SPI(Z) + #define Z_CS_PIN PE8 + #endif + #if AXIS_HAS_SPI(I) + #define I_CS_PIN PC5 + #endif + #if AXIS_HAS_SPI(J) + #define J_CS_PIN PE12 + #endif + #if AXIS_HAS_SPI(K) + #define K_CS_PIN PA2 + #endif + +#elif HAS_TMC_UART + + #define X_SERIAL_TX_PIN PD8 + #define X_SERIAL_RX_PIN X_SERIAL_TX_PIN + + #define Y_SERIAL_TX_PIN PB12 + #define Y_SERIAL_RX_PIN Y_SERIAL_TX_PIN + + #define Z_SERIAL_TX_PIN PE8 + #define Z_SERIAL_RX_PIN Z_SERIAL_TX_PIN + + #define I_SERIAL_TX_PIN PC5 + #define I_SERIAL_RX_PIN I_SERIAL_TX_PIN + + #define J_SERIAL_TX_PIN PE12 + #define J_SERIAL_RX_PIN J_SERIAL_TX_PIN + + #define K_SERIAL_TX_PIN PA2 + #define K_SERIAL_RX_PIN K_SERIAL_TX_PIN + + // Reduce baud rate to improve software serial reliability + #define TMC_BAUD_RATE 19200 + +#endif + +// +// Heaters / Fans +// +#define FAN_PIN PE2 +#define FAN1_PIN PE3 +#define FAN2_PIN PE4 +#define FAN3_PIN PE5 + +#define FAN_SOFT_PWM_REQUIRED + +// +// Neopixel +// +#define NEOPIXEL_PIN PC7 +#define NEOPIXEL2_PIN PC8 + +// +// SPI +// +#define MISO_PIN PB4 +#define MOSI_PIN PB5 +#define SCK_PIN PB3 + +#define TMC_SW_MISO MISO_PIN +#define TMC_SW_MOSI MOSI_PIN +#define TMC_SW_SCK SCK_PIN + +// +// I2C +// +#define I2C_SDA_PIN PB7 +#define I2C_SCL_PIN PB6 + +/** + * The index mobo rev03 has 3 aux ports. We define them here so they may be used + * in other places and to make sure someone doesn't have to go look up the pinout + * in the board files. Each 12 pin aux port has this pinout: + * + * VDC 1 2 GND + * 3.3V 3 4 SCL (I2C_SCL_PIN) + * PWM1 5 6 SDA (I2C_SDA_PIN) + * PWM2 7 8 CIPO (MISO_PIN) + * A1 9 10 COPI (MOSI_PIN) + * A2 11 12 SCK (SCK_PIN) + */ +#define LUMEN_AUX1_PWM1 PA15 +#define LUMEN_AUX1_PWM2 PA5 +#define LUMEN_AUX1_A1 PC0 +#define LUMEN_AUX1_A2 PC1 + +#define LUMEN_AUX2_PWM1 PA6 +#define LUMEN_AUX2_PWM2 PA7 +#define LUMEN_AUX2_A1 PC2 +#define LUMEN_AUX2_A2 PC3 + +#define LUMEN_AUX3_PWM1 PB8 +#define LUMEN_AUX3_PWM2 PB9 +#define LUMEN_AUX3_A1 PA0 +#define LUMEN_AUX3_A2 PA1 diff --git a/buildroot/share/PlatformIO/boards/marlin_opulo_lumen_rev4.json b/buildroot/share/PlatformIO/boards/marlin_opulo_lumen_rev4.json new file mode 100644 index 0000000000..ef5ebfa560 --- /dev/null +++ b/buildroot/share/PlatformIO/boards/marlin_opulo_lumen_rev4.json @@ -0,0 +1,51 @@ +{ + "build": { + "core": "stm32", + "cpu": "cortex-m4", + "extra_flags": "-DSTM32F407xx", + "f_cpu": "168000000L", + "hwids": [ + [ + "0x0483", + "0xdf11" + ], + [ + "0x1EAF", + "0x0003" + ], + [ + "0x0483", + "0x3748" + ] + ], + "mcu": "stm32f407vet6", + "variant": "MARLIN_F407VE" + }, + "debug": { + "jlink_device": "STM32F407VE", + "openocd_target": "stm32f4x", + "svd_path": "STM32F40x.svd" + }, + "frameworks": [ + "arduino", + "stm32cube" + ], + "name": "STM32F407VE (192k RAM. 512k Flash)", + "upload": { + "disable_flushing": false, + "maximum_ram_size": 131072, + "maximum_size": 524288, + "protocol": "dfu", + "protocols": [ + "stlink", + "dfu", + "jlink", + "blackmagic" + ], + "require_upload_port": true, + "use_1200bps_touch": false, + "wait_for_upload_port": false + }, + "url": "https://www.st.com/en/microcontrollers-microprocessors/stm32f407ve.html", + "vendor": "Generic" +} diff --git a/ini/stm32f4.ini b/ini/stm32f4.ini index 0857dec398..2c5aedbfe0 100644 --- a/ini/stm32f4.ini +++ b/ini/stm32f4.ini @@ -93,6 +93,17 @@ build_flags = ${stm32_variant.build_flags} -DUSBD_USE_CDC_COMPOSITE -DUSE_USB_FS extra_scripts = ${stm32_variant.extra_scripts} +# +# STM32F407VET6 Opulo Lumen REV4 +# +[env:Opulo_Lumen_REV4] +extends = stm32_variant +board = marlin_opulo_lumen_rev4 +build_flags = ${stm32_variant.build_flags} + -DARDUINO_BLACK_F407VE + -DUSBD_USE_CDC_COMPOSITE -DUSE_USB_FS +extra_scripts = ${stm32_variant.extra_scripts} + # # Anet ET4-MB_V1.x/ET4P-MB_V1.x (STM32F407VGT6 ARM Cortex-M4) #