andrey
/
Marlin_FB4S
1
0
Fork 0
Code Issues Pull Requests Projects Releases Wiki Activity
Browse Source

FLSun Hispeedv1 Board update (#19959) 

Co-authored-by: Scott Lahteine <thinkyhead@users.noreply.github.com>
vanilla_fb_2.0.x
Foxies 4 years ago
committed by Scott Lahteine
parent
172cc0dd03
commit
292e83466e
1 changed files with 86 additions and 102 deletions
Whitespace
Show all changes Ignore whitespace when comparing lines Ignore changes in amount of whitespace Ignore changes in whitespace at EOL
Split View
Diff Options
Show Stats Download Patch File Download Diff File
  1. 188
      Marlin/src/pins/stm32f1/pins_FLSUN_HISPEED.h

188
Marlin/src/pins/stm32f1/pins_FLSUN_HISPEED.h
View File

@ -50,15 +50,16 @@
//
#if EITHER(NO_EEPROM_SELECTED, FLASH_EEPROM_EMULATION)
#define FLASH_EEPROM_EMULATION
#define EEPROM_PAGE_SIZE (0x800U) // 2KB
#define EEPROM_PAGE_SIZE (0x800U) // 2KB
#define EEPROM_START_ADDRESS (0x8000000UL + (STM32_FLASH_SIZE) * 1024UL - (EEPROM_PAGE_SIZE) * 2UL)
#define MARLIN_EEPROM_SIZE EEPROM_PAGE_SIZE // 2KB
#endif
//
// SPI
// Note: FLSun Hispeed (clone MKS_Robin_miniV2) board is using SPI2 interface.
//
#define SPI_DEVICE 2
#define SPI_DEVICE 2
// SPI Flash
#define HAS_SPI_FLASH 1
@ -108,49 +109,26 @@
#define E0_STEP_PIN PD6 // E0_STEP
#define E0_DIR_PIN PD3 // E0_DIR
/**
* FLSUN Hi-Speed has no hard-wired UART pins for TMC drivers.
* Several wiring options are provided below, defaulting to
* to the most compatible.
*/
//
// Drivers
//
#if HAS_TMC220x
#if ENABLED(HARDWARE_SERIAL) /* TMC2209 */
#define X_SLAVE_ADDRESS 3 // | | :
#define Y_SLAVE_ADDRESS 2 // : | :
#define Z_SLAVE_ADDRESS 1 // | : :
//#define E0_SLAVE_ADDRESS 0 // : : :
#define X_SERIAL_TX_PIN PA9 // TXD1
#define X_SERIAL_RX_PIN PA9 // TXD1
#define Y_SERIAL_TX_PIN PA9 // TXD1
#define Y_SERIAL_RX_PIN PA9 // TXD1
#define Z_SERIAL_TX_PIN PA9 // TXD1
#define Z_SERIAL_RX_PIN PA9 // TXD1
#elif ENABLED(SOFTWARE_SERIAL) /* TMC220x */
/**
* TMC2208 stepper UART-configurable by PDN_UART pin
* Software serial
*/
#define X_SLAVE_ADDRESS 0
#define Y_SLAVE_ADDRESS 0
#define Z_SLAVE_ADDRESS 0
#define X_SERIAL_TX_PIN PA10 // RXD1
#define X_SERIAL_RX_PIN PA10 // RXD1
#define Y_SERIAL_TX_PIN PA9 // TXD1
#define Y_SERIAL_RX_PIN PA9 // TXD1
#define Z_SERIAL_TX_PIN PC7 // IO1
#define Z_SERIAL_RX_PIN PC7 // IO1
#endif
// Reduce baud rate to improve software serial reliability
#define TMC_BAUD_RATE 19200
// SoftwareSerial with one pin per driver
// Compatible with TMC2208 and TMC2209 drivers
#define X_SERIAL_TX_PIN PA10 // RXD1
#define X_SERIAL_RX_PIN PA10 // RXD1
#define Y_SERIAL_TX_PIN PA9 // TXD1
#define Y_SERIAL_RX_PIN PA9 // TXD1
#define Z_SERIAL_TX_PIN PC7 // IO1
#define Z_SERIAL_RX_PIN PC7 // IO1
#define TMC_BAUD_RATE 19200
#else
// Motor current PWM pins
#define MOTOR_CURRENT_PWM_XY_PIN PA6 // VREF2/3 CONTROL XY
#define MOTOR_CURRENT_PWM_Z_PIN PA7 // VREF4 CONTROL Z
@ -159,33 +137,33 @@
#define DEFAULT_PWM_MOTOR_CURRENT { 800, 800, 800 }
#endif
/**
* src: MKS Robin_Mini V2
* __ESP(M1)__ -J1-
* GND| 15 | | 08 |+3v3 (22)=>RXD1(PA10) //
* | 16 | | 07 |MOSI (21)=>TXD1(PA9) // active low, probably OK to leave floating
* IO2| 17 | | 06 |MISO (19)=>IO1(PC7) // Leave as unused (ESP3D software configures this with a pullup so OK to leave as floating)
* IO0| 18 | | 05 |CLK (18)=>IO0(PA8) // must be high (ESP3D software configures this with a pullup so OK to leave as floating)
* IO1| 19 | | 03 |EN (03)=>WIFI_EN() // Must be high for module to run
* | nc | | nc | (01)=>WIFI_CTRL(PA5)
* RX| 21 | | nc |
* TX| 22 | | 01 |RST
* ￣￣ AE￣￣
*
*/
#ifdef ESP_WIFI
#define WIFI_IO0_PIN PA8 // PC13 MKS ESP WIFI IO0 PIN
#define WIFI_IO1_PIN PC7 // MKS ESP WIFI IO1 PIN
#define WIFI_RESET_PIN PA5 // MKS ESP WIFI RESET PIN
#endif
/**
* MKS Robin_Wifi or another ESP8266 module
*
* __ESP(M1)__ -J1-
* GND| 15 | | 08 |+3v3 (22) RXD1 (PA10)
* | 16 | | 07 |MOSI (21) TXD1 (PA9) Active LOW, probably OK to leave floating
* IO2| 17 | | 06 |MISO (19) IO1 (PC7) Leave as unused (ESP3D software configures this with a pullup so OK to leave as floating)
* IO0| 18 | | 05 |CLK (18) IO0 (PA8) Must be HIGH (ESP3D software configures this with a pullup so OK to leave as floating)
* IO1| 19 | | 03 |EN (03) WIFI_EN Must be HIGH for module to run
* | nc | | nc | (01) WIFI_CTRL (PA5)
* RX| 21 | | nc |
* TX| 22 | | 01 |RST
* ￣￣ AE￣￣
*/
// Module ESP-WIFI
#define ESP_WIFI_MODULE_COM 2 // Must also set either SERIAL_PORT or SERIAL_PORT_2 to this
#define ESP_WIFI_MODULE_BAUDRATE BAUDRATE // Must use same BAUDRATE as SERIAL_PORT & SERIAL_PORT_2
#define ESP_WIFI_MODULE_RESET_PIN PA5 // WIFI CTRL/RST
#define ESP_WIFI_MODULE_ENABLE_PIN -1
#define ESP_WIFI_MODULE_TXD_PIN PA9 // MKS or ESP WIFI RX PIN
#define ESP_WIFI_MODULE_RXD_PIN PA10 // MKS or ESP WIFI TX PIN
#endif
//
// EXTRUDER
//
#if AXIS_DRIVER_TYPE(E0,TMC2208)||AXIS_DRIVER_TYPE(E0,TMC2209)
#define E0_SLAVE_ADDRESS 0
#if AXIS_DRIVER_TYPE_E0(TMC2208) || AXIS_DRIVER_TYPE_E0(TMC2209)
#define E0_SERIAL_TX_PIN PA8 // IO0
#define E0_SERIAL_RX_PIN PA8 // IO0
#define TMC_BAUD_RATE 19200
@ -199,7 +177,7 @@
#endif
//
// Temperature Sensors(THM)
// Temperature Sensors (THM)
//
#define TEMP_0_PIN PC1 // TEMP_E0
#define TEMP_BED_PIN PC0 // TEMP_BED
@ -211,7 +189,6 @@
#define HEATER_BED_PIN PA0 // HEATER_BED-WKUP
#define FAN_PIN PB1 // E_FAN
//#define CONTROLLER_FAN_PIN PD6 // BOARD FAN
//
// Misc. Functions
@ -221,12 +198,24 @@
#define POWER_LOSS_PIN PA2 // PW_DET (UPS) MKSPWC
#endif
/**
* Connector J2
* -------
* DIO O|1 2|O 3v3
* CSK O|3 5|O GND
* RST O|5 6|O GND
* -------
*/
//#define SW_DIO PA13
//#define SW_CLK PA14
//#define SW_RST NRST // (14)
//
// Power Supply Control
//
#if ENABLED(PSU_CONTROL)
#define KILL_PIN PA2 // PW_DET
#define KILL_PIN_INVERTING true //
#define KILL_PIN_INVERTING true
//#define PS_ON_PIN PA3 // PW_CN /PW_OFF
#endif
@ -240,28 +229,33 @@
//#define LED_PIN PB2 // BOOT1
#if ENABLED(NEOPIXEL_LED)
#define LED_PWM PA8
#define LED_PWM PC7 // IO1
#ifndef NEOPIXEL_PIN
#define NEOPIXEL_PIN LED_PWM // USED WIFI IO0/IO1/TX/RX PIN
#define NEOPIXEL_PIN LED_PWM // USED WIFI IO0/IO1 PIN
#endif
#endif
//Others test.
//#define SERVO0_PIN PA5 // WIFI CRTL
//#define GPIO_CLEAR PA8 // IO0
//#define GPIO_SET PA5
//
// SD Card
//
#define SDIO_SUPPORT
#define SDIO_CLOCK 4500000 // 4.5 MHz /* 18 MHz (18000000) or 4.5MHz (450000) */
//#define SDIO_CLOCK 18000000 // 18 MHz (18000000)
#if ENABLED(SDIO_SUPPORT)
#define SCK_PIN PB13 // SPI2
#define MISO_PIN PB14 // SPI2
#define MOSI_PIN PB15 // SPI2
#define SD_DETECT_PIN PD12 // SD_CD
#ifndef SDCARD_CONNECTION
#define SDCARD_CONNECTION ONBOARD
#endif
// Use the on-board card socket labeled SD_Extender
#if SD_CONNECTION_IS(CUSTOM_CABLE)
#define SCK_PIN PC12
#define MISO_PIN PC8
#define MOSI_PIN PD2
#define SS_PIN -1
#define SD_DETECT_PIN PD12 // SD_CD (if -1 no detection)
#else
#define SDIO_SUPPORT
#define SDIO_CLOCK 4500000 // 4.5 MHz
#define SDIO_READ_RETRIES 16
#define ONBOARD_SPI_DEVICE 1 // SPI1
#define ONBOARD_SD_CS_PIN PC11
#define SD_DETECT_PIN -1 // SD_CD (-1 active refresh)
#endif
//
@ -271,6 +265,10 @@
#define BEEPER_PIN PC5
#endif
#if ENABLED(SPEAKER) && BEEPER_PIN == PC5
#error "FLSun HiSpeed default BEEPER_PIN is not a SPEAKER."
#endif
/**
* Note: MKS Robin TFT screens use various TFT controllers
* Supported screens are based on the ILI9341, ST7789V and ILI9328 (320x240)
@ -284,26 +282,7 @@
* because Marlin uses the reset as a failsafe to revive a glitchy LCD.
*/
// MKS Robin TFT v2.0 with ILI9341
// Read display identification information (0xD3 on ILI9341)
//#define TOUCH_CALIBRATION_X 12013
//#define TOUCH_CALIBRATION_Y -8711
//#define TOUCH_OFFSET_X -32
//#define TOUCH_OFFSET_Y 256
// MKS Robin TFT v1.1 with ILI9328
//#define TOUCH_CALIBRATION_X -11792
//#define TOUCH_CALIBRATION_Y 8947
//#define TOUCH_OFFSET_X 342
//#define TOUCH_OFFSET_Y -19
// MKS Robin TFT v1.1 with R61505
//#define TOUCH_CALIBRATION_X 12489
//#define TOUCH_CALIBRATION_Y 9210
//#define TOUCH_OFFSET_X -52
//#define TOUCH_OFFSET_Y -17
// QQS-Pro uses MKS Robin TFT v2.0
// QQS-Pro uses MKS Robin TFT v2.0 320x240
// Shared FSMC Configs
#if HAS_FSMC_TFT
@ -320,8 +299,13 @@
#define FSMC_DMA_DEV DMA2
#define FSMC_DMA_CHANNEL DMA_CH5
#define TOUCH_BUTTONS_HW_SPI
#define TOUCH_BUTTONS_HW_SPI_DEVICE 2
#define TFT_BUFFER_SIZE 14400
#if ENABLED(TFT_CLASSIC_UI)
#define TFT_MARLINBG_COLOR 0x3186 // White
#define TFT_MARLINUI_COLOR 0xC7B6 // green
#define TFT_BTARROWS_COLOR 0xDEE6 // Yellow
#define TFT_BTOKMENU_COLOR 0x145F // Cyan
#endif
#endif
#if NEED_TOUCH_PINS

Write Preview
Loading…
Cancel
Save