From becbfe106538b7844d71d6717feeac0eedbaa396 Mon Sep 17 00:00:00 2001 From: Ruwan J Egoda Gamage Date: Sat, 12 Dec 2015 20:57:36 -0500 Subject: [PATCH 1/7] Fixing Rigidbot LCD Panel Support --- Marlin/cardreader.cpp | 2 +- .../RigidBot/Configuration.h | 11 ++-- .../RigidBot/Configuration_adv.h | 8 +-- Marlin/pins_RIGIDBOARD.h | 31 +++++------ Marlin/ultralcd.cpp | 51 ++++++++++++++++--- Marlin/ultralcd.h | 3 ++ 6 files changed, 77 insertions(+), 29 deletions(-) diff --git a/Marlin/cardreader.cpp b/Marlin/cardreader.cpp index 61f4a93ccf..f6b55f9301 100644 --- a/Marlin/cardreader.cpp +++ b/Marlin/cardreader.cpp @@ -196,7 +196,7 @@ void CardReader::initsd() { if (root.isOpen()) root.close(); #if ENABLED(SDEXTRASLOW) - #define SPI_SPEED SPI_QUARTER_SPEED + #define SPI_SPEED SPI_SIXTEENTH_SPEED #elif ENABLED(SDSLOW) #define SPI_SPEED SPI_HALF_SPEED #else diff --git a/Marlin/example_configurations/RigidBot/Configuration.h b/Marlin/example_configurations/RigidBot/Configuration.h index 987fc36d33..e0c956e17f 100644 --- a/Marlin/example_configurations/RigidBot/Configuration.h +++ b/Marlin/example_configurations/RigidBot/Configuration.h @@ -219,6 +219,11 @@ Here are some standard links for getting your machine calibrated: //#define DEFAULT_Ki 0.85 //#define DEFAULT_Kd 245 + // E3D w/ rigidbot cartridge + //#define DEFAULT_Kp 16.30 + //#define DEFAULT_Ki 0.95 + //#define DEFAULT_Kd 69.69 + #endif // PIDTEMP //=========================================================================== @@ -611,7 +616,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily). // M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to. //define this to enable EEPROM support -//#define EEPROM_SETTINGS +#define EEPROM_SETTINGS #if ENABLED(EEPROM_SETTINGS) // To disable EEPROM Serial responses and decrease program space by ~1700 byte: comment this out: @@ -651,10 +656,10 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //#define ULTRA_LCD //general LCD support, also 16x2 //#define DOGLCD // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family) -//#define SDSUPPORT // Enable SD Card Support in Hardware Console +#define SDSUPPORT // Enable SD Card Support in Hardware Console // Changed behaviour! If you need SDSUPPORT uncomment it! //#define SDSLOW // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) -//#define SDEXTRASLOW // Use even slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) +#define SDEXTRASLOW // Use even slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) //#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication //#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder //#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking diff --git a/Marlin/example_configurations/RigidBot/Configuration_adv.h b/Marlin/example_configurations/RigidBot/Configuration_adv.h index fe8e2db97d..5a70c9d5cc 100644 --- a/Marlin/example_configurations/RigidBot/Configuration_adv.h +++ b/Marlin/example_configurations/RigidBot/Configuration_adv.h @@ -279,9 +279,9 @@ //=============================Additional Features=========================== //=========================================================================== -#define ENCODER_RATE_MULTIPLIER // If defined, certain menu edit operations automatically multiply the steps when the encoder is moved quickly -#define ENCODER_10X_STEPS_PER_SEC 75 // If the encoder steps per sec exceeds this value, multiply steps moved x10 to quickly advance the value -#define ENCODER_100X_STEPS_PER_SEC 160 // If the encoder steps per sec exceeds this value, multiply steps moved x100 to really quickly advance the value +//#define ENCODER_RATE_MULTIPLIER // If defined, certain menu edit operations automatically multiply the steps when the encoder is moved quickly +//#define ENCODER_10X_STEPS_PER_SEC 75 // If the encoder steps per sec exceeds this value, multiply steps moved x10 to quickly advance the value +//#define ENCODER_100X_STEPS_PER_SEC 160 // If the encoder steps per sec exceeds this value, multiply steps moved x100 to really quickly advance the value //#define CHDK 4 //Pin for triggering CHDK to take a picture see how to use it here http://captain-slow.dk/2014/03/09/3d-printing-timelapses/ #define CHDK_DELAY 50 //How long in ms the pin should stay HIGH before going LOW again @@ -414,7 +414,7 @@ const unsigned int dropsegments = 5; //everything with less than this number of //The ASCII buffer for receiving from the serial: #define MAX_CMD_SIZE 96 -#define BUFSIZE 4 +#define BUFSIZE 8 // Bad Serial-connections can miss a received command by sending an 'ok' // Therefore some clients abort after 30 seconds in a timeout. diff --git a/Marlin/pins_RIGIDBOARD.h b/Marlin/pins_RIGIDBOARD.h index 4f8abc1266..3fe46a9ff6 100644 --- a/Marlin/pins_RIGIDBOARD.h +++ b/Marlin/pins_RIGIDBOARD.h @@ -5,7 +5,10 @@ #include "pins_RAMPS_13.h" #if ENABLED(Z_MIN_PROBE_ENDSTOP) - #define Z_MIN_PROBE_PIN 19 + #undef Z_MAX_PIN + #define Z_MAX_PIN -1 + #undef Z_MIN_PROBE_PIN + #define Z_MIN_PROBE_PIN 19 // Z-MAX pin J14 End Stops #endif #undef HEATER_0_PIN @@ -25,24 +28,22 @@ #undef BEEPER_PIN #define BEEPER_PIN -1 - #undef SD_DETECT_PIN - #define SD_DETECT_PIN 22 - - // Extra button definitions, substitute for EN1 / EN2 - #define BTN_UP 37 // BTN_EN1 - #define BTN_DWN 35 // BTN_EN2 - #define BTN_LFT 33 - #define BTN_RT 32 - - // Marlin can respond to UP/DOWN by default - // #undef BTN_EN1 - // #undef BTN_EN2 - //#define BTN_EN1 -1 - //#define BTN_EN2 -1 + // Direction buttons + #define BTN_UP 37 + #define BTN_DWN 35 + #define BTN_LFT 33 + #define BTN_RT 32 + // 'R' button #undef BTN_ENC #define BTN_ENC 31 + // Disable encoder + #undef BTN_EN1 + #define BTN_EN1 -1 + #undef BTN_EN2 + #define BTN_EN2 -1 + #undef SD_DETECT_PIN #define SD_DETECT_PIN 22 diff --git a/Marlin/ultralcd.cpp b/Marlin/ultralcd.cpp index a23995d7c8..2f835a3c69 100644 --- a/Marlin/ultralcd.cpp +++ b/Marlin/ultralcd.cpp @@ -218,6 +218,9 @@ static void lcd_status_screen(); #if ENABLED(REPRAPWORLD_KEYPAD) volatile uint8_t buttons_reprapworld_keypad; // to store the keypad shift register values #endif + #if ENABLED(RIGIDBOT_PANEL) + volatile millis_t next_fake_encoder_update_ms; + #endif #if ENABLED(LCD_HAS_SLOW_BUTTONS) volatile uint8_t slow_buttons; // Bits of the pressed buttons. @@ -1524,11 +1527,15 @@ void lcd_init() { lcd_implementation_init(); #if ENABLED(NEWPANEL) + #if BTN_EN1 > 0 + SET_INPUT(BTN_EN1); + WRITE(BTN_EN1, HIGH); + #endif - SET_INPUT(BTN_EN1); - SET_INPUT(BTN_EN2); - WRITE(BTN_EN1, HIGH); - WRITE(BTN_EN2, HIGH); + #if BTN_EN2 > 0 + SET_INPUT(BTN_EN2); + WRITE(BTN_EN2, HIGH); + #endif #if BTN_ENC > 0 SET_INPUT(BTN_ENC); @@ -1543,6 +1550,14 @@ void lcd_init() { WRITE(SHIFT_LD, HIGH); #endif + #ifdef RIGIDBOT_PANEL + pinMode(BTN_UP,INPUT); + pinMode(BTN_DWN,INPUT); + pinMode(BTN_LFT,INPUT); + pinMode(BTN_RT,INPUT); + next_fake_encoder_update_ms = 0; + #endif + #else // Not NEWPANEL #if ENABLED(SR_LCD_2W_NL) // Non latching 2 wire shift register @@ -1843,8 +1858,32 @@ void lcd_reset_alert_level() { lcd_status_message_level = 0; } void lcd_buttons_update() { #if ENABLED(NEWPANEL) uint8_t newbutton = 0; - if (READ(BTN_EN1) == 0) newbutton |= EN_A; - if (READ(BTN_EN2) == 0) newbutton |= EN_B; + #if BTN_EN1 > 0 + if (READ(BTN_EN1) == 0) newbutton |= EN_A; + #endif + #if BTN_EN2 > 0 + if (READ(BTN_EN2) == 0) newbutton |= EN_B; + #endif + #if ENABLED(RIGIDBOT_PANEL) + if (millis() > next_fake_encoder_update_ms && READ(BTN_UP) == 0) { + encoderDiff = -1 * ENCODER_STEPS_PER_MENU_ITEM; + next_fake_encoder_update_ms = millis() + 300; + } + if (millis() > next_fake_encoder_update_ms && READ(BTN_DWN) == 0) { + encoderDiff = ENCODER_STEPS_PER_MENU_ITEM; + next_fake_encoder_update_ms = millis() + 300; + } + if (millis() > next_fake_encoder_update_ms && READ(BTN_LFT) == 0) { + encoderDiff = -1 * ENCODER_PULSES_PER_STEP; + next_fake_encoder_update_ms = millis() + 300; + } + if (millis() > next_fake_encoder_update_ms && READ(BTN_RT) == 0) { + encoderDiff = ENCODER_PULSES_PER_STEP; + next_fake_encoder_update_ms = millis() + 300; + } + #endif + + #if BTN_ENC > 0 if (millis() > next_button_update_ms && READ(BTN_ENC) == 0) newbutton |= EN_C; #endif diff --git a/Marlin/ultralcd.h b/Marlin/ultralcd.h index 23df71cc44..b73b26f163 100644 --- a/Marlin/ultralcd.h +++ b/Marlin/ultralcd.h @@ -41,6 +41,9 @@ #if ENABLED(REPRAPWORLD_KEYPAD) extern volatile uint8_t buttons_reprapworld_keypad; // to store the keypad shift register values #endif + #if ENABLED(RIGIDBOT_PANEL) + extern volatile millis_t next_fake_encoder_update_ms; + #endif #else FORCE_INLINE void lcd_buttons_update() {} #endif From 6f9e9c0e4f97ebb0b22fbb4b9957762d1434ac31 Mon Sep 17 00:00:00 2001 From: Ruwan J Egoda Gamage Date: Sun, 13 Dec 2015 12:40:48 -0500 Subject: [PATCH 2/7] Cleaning up, getting rid of the fake encoder count variable. --- Marlin/ultralcd.cpp | 40 +++++++++++++++++++--------------------- Marlin/ultralcd.h | 3 --- 2 files changed, 19 insertions(+), 24 deletions(-) diff --git a/Marlin/ultralcd.cpp b/Marlin/ultralcd.cpp index 2f835a3c69..c6a951c7fa 100644 --- a/Marlin/ultralcd.cpp +++ b/Marlin/ultralcd.cpp @@ -218,9 +218,6 @@ static void lcd_status_screen(); #if ENABLED(REPRAPWORLD_KEYPAD) volatile uint8_t buttons_reprapworld_keypad; // to store the keypad shift register values #endif - #if ENABLED(RIGIDBOT_PANEL) - volatile millis_t next_fake_encoder_update_ms; - #endif #if ENABLED(LCD_HAS_SLOW_BUTTONS) volatile uint8_t slow_buttons; // Bits of the pressed buttons. @@ -1555,7 +1552,6 @@ void lcd_init() { pinMode(BTN_DWN,INPUT); pinMode(BTN_LFT,INPUT); pinMode(BTN_RT,INPUT); - next_fake_encoder_update_ms = 0; #endif #else // Not NEWPANEL @@ -1685,7 +1681,7 @@ void lcd_update() { int32_t encoderMovementSteps = abs(encoderDiff) / ENCODER_PULSES_PER_STEP; if (lastEncoderMovementMillis != 0) { - // Note that the rate is always calculated between to passes through the + // Note that the rate is always calculated between to passes through the // loop and that the abs of the encoderDiff value is tracked. float encoderStepRate = (float)(encoderMovementSteps) / ((float)(ms - lastEncoderMovementMillis)) * 1000.0; @@ -1865,25 +1861,27 @@ void lcd_reset_alert_level() { lcd_status_message_level = 0; } if (READ(BTN_EN2) == 0) newbutton |= EN_B; #endif #if ENABLED(RIGIDBOT_PANEL) - if (millis() > next_fake_encoder_update_ms && READ(BTN_UP) == 0) { - encoderDiff = -1 * ENCODER_STEPS_PER_MENU_ITEM; - next_fake_encoder_update_ms = millis() + 300; - } - if (millis() > next_fake_encoder_update_ms && READ(BTN_DWN) == 0) { - encoderDiff = ENCODER_STEPS_PER_MENU_ITEM; - next_fake_encoder_update_ms = millis() + 300; - } - if (millis() > next_fake_encoder_update_ms && READ(BTN_LFT) == 0) { - encoderDiff = -1 * ENCODER_PULSES_PER_STEP; - next_fake_encoder_update_ms = millis() + 300; - } - if (millis() > next_fake_encoder_update_ms && READ(BTN_RT) == 0) { - encoderDiff = ENCODER_PULSES_PER_STEP; - next_fake_encoder_update_ms = millis() + 300; + millis_t now = millis(); + if (now > next_button_update_ms) { + if (READ(BTN_UP) == 0) { + encoderDiff = -1 * ENCODER_STEPS_PER_MENU_ITEM; + next_button_update_ms = now + 300; + } + else if (READ(BTN_DWN) == 0) { + encoderDiff = ENCODER_STEPS_PER_MENU_ITEM; + next_button_update_ms = now + 300; + } + else if (READ(BTN_LFT) == 0) { + encoderDiff = -1 * ENCODER_PULSES_PER_STEP; + next_button_update_ms = now + 300; + } + else if (READ(BTN_RT) == 0) { + encoderDiff = ENCODER_PULSES_PER_STEP; + next_button_update_ms = now + 300; + } } #endif - #if BTN_ENC > 0 if (millis() > next_button_update_ms && READ(BTN_ENC) == 0) newbutton |= EN_C; #endif diff --git a/Marlin/ultralcd.h b/Marlin/ultralcd.h index b73b26f163..23df71cc44 100644 --- a/Marlin/ultralcd.h +++ b/Marlin/ultralcd.h @@ -41,9 +41,6 @@ #if ENABLED(REPRAPWORLD_KEYPAD) extern volatile uint8_t buttons_reprapworld_keypad; // to store the keypad shift register values #endif - #if ENABLED(RIGIDBOT_PANEL) - extern volatile millis_t next_fake_encoder_update_ms; - #endif #else FORCE_INLINE void lcd_buttons_update() {} #endif From 1b7c44362872650b6ae9a792dc49742966a47aed Mon Sep 17 00:00:00 2001 From: Ruwan J Egoda Gamage Date: Sun, 13 Dec 2015 15:47:10 -0500 Subject: [PATCH 3/7] Adding SDULTRASLOW variable. Instead of changing SDEXTRASLOW variable to a slower speed, the new SDULTRASLOW is used for rigidbot panel. --- Marlin/cardreader.cpp | 4 +++- Marlin/example_configurations/Felix/Configuration.h | 1 + Marlin/example_configurations/Felix/Configuration_DUAL.h | 1 + Marlin/example_configurations/Hephestos/Configuration.h | 1 + Marlin/example_configurations/K8200/Configuration.h | 1 + .../RepRapWorld/Megatronics/Configuration.h | 1 + Marlin/example_configurations/RigidBot/Configuration.h | 3 ++- Marlin/example_configurations/SCARA/Configuration.h | 1 + Marlin/example_configurations/TAZ4/Configuration.h | 1 + Marlin/example_configurations/WITBOX/Configuration.h | 1 + Marlin/example_configurations/adafruit/ST7565/Configuration.h | 1 + Marlin/example_configurations/delta/biv2.5/Configuration.h | 1 + Marlin/example_configurations/delta/generic/Configuration.h | 1 + .../example_configurations/delta/kossel_mini/Configuration.h | 1 + .../example_configurations/delta/kossel_pro/Configuration.h | 1 + Marlin/example_configurations/makibox/Configuration.h | 1 + Marlin/example_configurations/tvrrug/Round2/Configuration.h | 1 + 17 files changed, 20 insertions(+), 2 deletions(-) diff --git a/Marlin/cardreader.cpp b/Marlin/cardreader.cpp index f6b55f9301..5b69174da5 100644 --- a/Marlin/cardreader.cpp +++ b/Marlin/cardreader.cpp @@ -195,8 +195,10 @@ void CardReader::initsd() { cardOK = false; if (root.isOpen()) root.close(); - #if ENABLED(SDEXTRASLOW) + #if ENABLED(SDULTRASLOW) #define SPI_SPEED SPI_SIXTEENTH_SPEED + #elif ENABLED(SDEXTRASLOW) + #define SPI_SPEED SPI_QUARTER_SPEED #elif ENABLED(SDSLOW) #define SPI_SPEED SPI_HALF_SPEED #else diff --git a/Marlin/example_configurations/Felix/Configuration.h b/Marlin/example_configurations/Felix/Configuration.h index f946d35c0a..ba67118989 100644 --- a/Marlin/example_configurations/Felix/Configuration.h +++ b/Marlin/example_configurations/Felix/Configuration.h @@ -651,6 +651,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // Changed behaviour! If you need SDSUPPORT uncomment it! //#define SDSLOW // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) //#define SDEXTRASLOW // Use even slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) +//#define SDULTRASLOW // Use slowest SD transfer mode (not normally needed - uncomment if you're getting volume init error) //#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication //#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder //#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking diff --git a/Marlin/example_configurations/Felix/Configuration_DUAL.h b/Marlin/example_configurations/Felix/Configuration_DUAL.h index bd7b8eed4e..1d21b37531 100644 --- a/Marlin/example_configurations/Felix/Configuration_DUAL.h +++ b/Marlin/example_configurations/Felix/Configuration_DUAL.h @@ -620,6 +620,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // Changed behaviour! If you need SDSUPPORT uncomment it! //#define SDSLOW // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) //#define SDEXTRASLOW // Use even slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) +//#define SDULTRASLOW // Use slowest SD transfer mode (not normally needed - uncomment if you're getting volume init error) //#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication //#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder //#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking diff --git a/Marlin/example_configurations/Hephestos/Configuration.h b/Marlin/example_configurations/Hephestos/Configuration.h index 9fe3715f7f..4e7bc9c713 100644 --- a/Marlin/example_configurations/Hephestos/Configuration.h +++ b/Marlin/example_configurations/Hephestos/Configuration.h @@ -660,6 +660,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo #define SDSUPPORT // Enable SD Card Support in Hardware Console //#define SDSLOW // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) //#define SDEXTRASLOW // Use even slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) +//#define SDULTRASLOW // Use slowest SD transfer mode (not normally needed - uncomment if you're getting volume init error) //#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication //#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder //#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking diff --git a/Marlin/example_configurations/K8200/Configuration.h b/Marlin/example_configurations/K8200/Configuration.h index 426d8e9b68..220532af31 100644 --- a/Marlin/example_configurations/K8200/Configuration.h +++ b/Marlin/example_configurations/K8200/Configuration.h @@ -656,6 +656,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // Changed behaviour! If you need SDSUPPORT uncomment it! //#define SDSLOW // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) //#define SDEXTRASLOW // Use even slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) +//#define SDULTRASLOW // Use slowest SD transfer mode (not normally needed - uncomment if you're getting volume init error) //#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication //#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder //#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking diff --git a/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h b/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h index e03debc8fc..9b628d9ff1 100644 --- a/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h +++ b/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h @@ -668,6 +668,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l #define SDSUPPORT // Enable SD Card Support in Hardware Console //#define SDSLOW // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) //#define SDEXTRASLOW // Use even slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) +//#define SDULTRASLOW // Use slowest SD transfer mode (not normally needed - uncomment if you're getting volume init error) #define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication //#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder //#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking diff --git a/Marlin/example_configurations/RigidBot/Configuration.h b/Marlin/example_configurations/RigidBot/Configuration.h index e0c956e17f..ca1df7fc3e 100644 --- a/Marlin/example_configurations/RigidBot/Configuration.h +++ b/Marlin/example_configurations/RigidBot/Configuration.h @@ -659,7 +659,8 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l #define SDSUPPORT // Enable SD Card Support in Hardware Console // Changed behaviour! If you need SDSUPPORT uncomment it! //#define SDSLOW // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) -#define SDEXTRASLOW // Use even slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) +//#define SDEXTRASLOW // Use even slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) +#define SDULTRASLOW // Use slowest SD transfer mode (not normally needed - uncomment if you're getting volume init error) //#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication //#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder //#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking diff --git a/Marlin/example_configurations/SCARA/Configuration.h b/Marlin/example_configurations/SCARA/Configuration.h index 05c315917f..881c607656 100644 --- a/Marlin/example_configurations/SCARA/Configuration.h +++ b/Marlin/example_configurations/SCARA/Configuration.h @@ -676,6 +676,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // Changed behaviour! If you need SDSUPPORT uncomment it! //#define SDSLOW // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) //#define SDEXTRASLOW // Use even slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) +//#define SDULTRASLOW // Use slowest SD transfer mode (not normally needed - uncomment if you're getting volume init error) //#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication //#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder //#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking diff --git a/Marlin/example_configurations/TAZ4/Configuration.h b/Marlin/example_configurations/TAZ4/Configuration.h index 484d32da14..aa839b8b95 100644 --- a/Marlin/example_configurations/TAZ4/Configuration.h +++ b/Marlin/example_configurations/TAZ4/Configuration.h @@ -687,6 +687,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // Changed behaviour! If you need SDSUPPORT uncomment it! //#define SDSLOW // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) //#define SDEXTRASLOW // Use even slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) +//#define SDULTRASLOW // Use slowest SD transfer mode (not normally needed - uncomment if you're getting volume init error) //#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication #define ENCODER_PULSES_PER_STEP 2 // Increase if you have a high resolution encoder #define ENCODER_STEPS_PER_MENU_ITEM 1 // Set according to ENCODER_PULSES_PER_STEP or your liking diff --git a/Marlin/example_configurations/WITBOX/Configuration.h b/Marlin/example_configurations/WITBOX/Configuration.h index 2d235e59e7..5443f51ee5 100644 --- a/Marlin/example_configurations/WITBOX/Configuration.h +++ b/Marlin/example_configurations/WITBOX/Configuration.h @@ -659,6 +659,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo #define SDSUPPORT // Enable SD Card Support in Hardware Console //#define SDSLOW // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) //#define SDEXTRASLOW // Use even slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) +//#define SDULTRASLOW // Use slowest SD transfer mode (not normally needed - uncomment if you're getting volume init error) //#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication //#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder //#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking diff --git a/Marlin/example_configurations/adafruit/ST7565/Configuration.h b/Marlin/example_configurations/adafruit/ST7565/Configuration.h index 442ee1d7b4..4032fbdde0 100644 --- a/Marlin/example_configurations/adafruit/ST7565/Configuration.h +++ b/Marlin/example_configurations/adafruit/ST7565/Configuration.h @@ -668,6 +668,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l #define SDSUPPORT // Enable SD Card Support in Hardware Console #define SDSLOW // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) //#define SDEXTRASLOW // Use even slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) +//#define SDULTRASLOW // Use slowest SD transfer mode (not normally needed - uncomment if you're getting volume init error) //#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication //#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder //#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking diff --git a/Marlin/example_configurations/delta/biv2.5/Configuration.h b/Marlin/example_configurations/delta/biv2.5/Configuration.h index faa271dab5..2289d3d0d4 100644 --- a/Marlin/example_configurations/delta/biv2.5/Configuration.h +++ b/Marlin/example_configurations/delta/biv2.5/Configuration.h @@ -790,6 +790,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo // Changed behaviour! If you need SDSUPPORT uncomment it! //#define SDSLOW // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) //#define SDEXTRASLOW // Use even slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) +//#define SDULTRASLOW // Use slowest SD transfer mode (not normally needed - uncomment if you're getting volume init error) //#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication //#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder //#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking diff --git a/Marlin/example_configurations/delta/generic/Configuration.h b/Marlin/example_configurations/delta/generic/Configuration.h index f488163333..11e263c81b 100644 --- a/Marlin/example_configurations/delta/generic/Configuration.h +++ b/Marlin/example_configurations/delta/generic/Configuration.h @@ -791,6 +791,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo // Changed behaviour! If you need SDSUPPORT uncomment it! //#define SDSLOW // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) //#define SDEXTRASLOW // Use even slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) +//#define SDULTRASLOW // Use slowest SD transfer mode (not normally needed - uncomment if you're getting volume init error) //#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication //#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder //#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking diff --git a/Marlin/example_configurations/delta/kossel_mini/Configuration.h b/Marlin/example_configurations/delta/kossel_mini/Configuration.h index 3a94ce2f51..fe458ed0f7 100644 --- a/Marlin/example_configurations/delta/kossel_mini/Configuration.h +++ b/Marlin/example_configurations/delta/kossel_mini/Configuration.h @@ -795,6 +795,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // Changed behaviour! If you need SDSUPPORT uncomment it! //#define SDSLOW // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) //#define SDEXTRASLOW // Use even slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) +//#define SDULTRASLOW // Use slowest SD transfer mode (not normally needed - uncomment if you're getting volume init error) //#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication //#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder //#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking diff --git a/Marlin/example_configurations/delta/kossel_pro/Configuration.h b/Marlin/example_configurations/delta/kossel_pro/Configuration.h index 592471dd25..e3510fb741 100644 --- a/Marlin/example_configurations/delta/kossel_pro/Configuration.h +++ b/Marlin/example_configurations/delta/kossel_pro/Configuration.h @@ -785,6 +785,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l #define SDSUPPORT // Enable SD Card Support in Hardware Console //#define SDSLOW // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) //#define SDEXTRASLOW // Use even slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) +//#define SDULTRASLOW // Use slowest SD transfer mode (not normally needed - uncomment if you're getting volume init error) //#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication //#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder //#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking diff --git a/Marlin/example_configurations/makibox/Configuration.h b/Marlin/example_configurations/makibox/Configuration.h index 2f8fd73ba8..c16da81014 100644 --- a/Marlin/example_configurations/makibox/Configuration.h +++ b/Marlin/example_configurations/makibox/Configuration.h @@ -670,6 +670,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l #define SDSUPPORT // Enable SD Card Support in Hardware Console #define SDSLOW // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) //#define SDEXTRASLOW // Use even slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) +//#define SDULTRASLOW // Use slowest SD transfer mode (not normally needed - uncomment if you're getting volume init error) //#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication //#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder //#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking diff --git a/Marlin/example_configurations/tvrrug/Round2/Configuration.h b/Marlin/example_configurations/tvrrug/Round2/Configuration.h index 9a6aac98d3..a74d2e51bc 100644 --- a/Marlin/example_configurations/tvrrug/Round2/Configuration.h +++ b/Marlin/example_configurations/tvrrug/Round2/Configuration.h @@ -663,6 +663,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo // Changed behaviour! If you need SDSUPPORT uncomment it! //#define SDSLOW // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) //#define SDEXTRASLOW // Use even slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) +//#define SDULTRASLOW // Use slowest SD transfer mode (not normally needed - uncomment if you're getting volume init error) //#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication //#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder //#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking From 1833049b8a043994b33e57459370a7f9de75456e Mon Sep 17 00:00:00 2001 From: Ruwan J Egoda Gamage Date: Sun, 13 Dec 2015 22:06:03 -0500 Subject: [PATCH 4/7] reusing millis() --- Marlin/ultralcd.cpp | 7 ++++--- 1 file changed, 4 insertions(+), 3 deletions(-) diff --git a/Marlin/ultralcd.cpp b/Marlin/ultralcd.cpp index c6a951c7fa..a671a707e3 100644 --- a/Marlin/ultralcd.cpp +++ b/Marlin/ultralcd.cpp @@ -1860,8 +1860,10 @@ void lcd_reset_alert_level() { lcd_status_message_level = 0; } #if BTN_EN2 > 0 if (READ(BTN_EN2) == 0) newbutton |= EN_B; #endif - #if ENABLED(RIGIDBOT_PANEL) + #if ENABLED(RIGIDBOT_PANEL) || BTN_ENC > 0 millis_t now = millis(); + #endif + #if ENABLED(RIGIDBOT_PANEL) if (now > next_button_update_ms) { if (READ(BTN_UP) == 0) { encoderDiff = -1 * ENCODER_STEPS_PER_MENU_ITEM; @@ -1881,9 +1883,8 @@ void lcd_reset_alert_level() { lcd_status_message_level = 0; } } } #endif - #if BTN_ENC > 0 - if (millis() > next_button_update_ms && READ(BTN_ENC) == 0) newbutton |= EN_C; + if (now > next_button_update_ms && READ(BTN_ENC) == 0) newbutton |= EN_C; #endif buttons = newbutton; #if ENABLED(LCD_HAS_SLOW_BUTTONS) From b58083b0fa9af218689efcc1b0c042f2acfc8d30 Mon Sep 17 00:00:00 2001 From: Ruwan J Egoda Gamage Date: Sun, 13 Dec 2015 23:23:01 -0500 Subject: [PATCH 5/7] Getting rid of SDEXTRASLOW, SDSLOW variables. --- Marlin/cardreader.cpp | 8 +------- Marlin/example_configurations/Felix/Configuration.h | 4 +--- Marlin/example_configurations/Felix/Configuration_DUAL.h | 4 +--- Marlin/example_configurations/Hephestos/Configuration.h | 4 +--- Marlin/example_configurations/K8200/Configuration.h | 4 +--- .../RepRapWorld/Megatronics/Configuration.h | 4 +--- Marlin/example_configurations/RigidBot/Configuration.h | 4 +--- Marlin/example_configurations/SCARA/Configuration.h | 4 +--- Marlin/example_configurations/TAZ4/Configuration.h | 4 +--- Marlin/example_configurations/WITBOX/Configuration.h | 4 +--- .../adafruit/ST7565/Configuration.h | 4 +--- .../example_configurations/delta/biv2.5/Configuration.h | 4 +--- .../example_configurations/delta/generic/Configuration.h | 4 +--- .../delta/kossel_mini/Configuration.h | 4 +--- .../delta/kossel_pro/Configuration.h | 4 +--- Marlin/example_configurations/makibox/Configuration.h | 4 +--- .../example_configurations/tvrrug/Round2/Configuration.h | 4 +--- 17 files changed, 17 insertions(+), 55 deletions(-) diff --git a/Marlin/cardreader.cpp b/Marlin/cardreader.cpp index 5b69174da5..dd4dee3af6 100644 --- a/Marlin/cardreader.cpp +++ b/Marlin/cardreader.cpp @@ -195,13 +195,7 @@ void CardReader::initsd() { cardOK = false; if (root.isOpen()) root.close(); - #if ENABLED(SDULTRASLOW) - #define SPI_SPEED SPI_SIXTEENTH_SPEED - #elif ENABLED(SDEXTRASLOW) - #define SPI_SPEED SPI_QUARTER_SPEED - #elif ENABLED(SDSLOW) - #define SPI_SPEED SPI_HALF_SPEED - #else + #ifndef SPI_SPEED #define SPI_SPEED SPI_FULL_SPEED #endif diff --git a/Marlin/example_configurations/Felix/Configuration.h b/Marlin/example_configurations/Felix/Configuration.h index ba67118989..0d1eb86460 100644 --- a/Marlin/example_configurations/Felix/Configuration.h +++ b/Marlin/example_configurations/Felix/Configuration.h @@ -649,9 +649,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //#define DOGLCD // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family) //#define SDSUPPORT // Enable SD Card Support in Hardware Console // Changed behaviour! If you need SDSUPPORT uncomment it! -//#define SDSLOW // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) -//#define SDEXTRASLOW // Use even slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) -//#define SDULTRASLOW // Use slowest SD transfer mode (not normally needed - uncomment if you're getting volume init error) +//#define SPI_SPEED SPI_HALF_SPEED // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) //#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication //#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder //#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking diff --git a/Marlin/example_configurations/Felix/Configuration_DUAL.h b/Marlin/example_configurations/Felix/Configuration_DUAL.h index 1d21b37531..d91caae685 100644 --- a/Marlin/example_configurations/Felix/Configuration_DUAL.h +++ b/Marlin/example_configurations/Felix/Configuration_DUAL.h @@ -618,9 +618,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //#define DOGLCD // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family) //#define SDSUPPORT // Enable SD Card Support in Hardware Console // Changed behaviour! If you need SDSUPPORT uncomment it! -//#define SDSLOW // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) -//#define SDEXTRASLOW // Use even slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) -//#define SDULTRASLOW // Use slowest SD transfer mode (not normally needed - uncomment if you're getting volume init error) +//#define SPI_SPEED SPI_HALF_SPEED // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) //#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication //#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder //#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking diff --git a/Marlin/example_configurations/Hephestos/Configuration.h b/Marlin/example_configurations/Hephestos/Configuration.h index 4e7bc9c713..10950b27bc 100644 --- a/Marlin/example_configurations/Hephestos/Configuration.h +++ b/Marlin/example_configurations/Hephestos/Configuration.h @@ -658,9 +658,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo #define ULTRA_LCD //general LCD support, also 16x2 //#define DOGLCD // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family) #define SDSUPPORT // Enable SD Card Support in Hardware Console -//#define SDSLOW // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) -//#define SDEXTRASLOW // Use even slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) -//#define SDULTRASLOW // Use slowest SD transfer mode (not normally needed - uncomment if you're getting volume init error) +//#define SPI_SPEED SPI_HALF_SPEED // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) //#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication //#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder //#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking diff --git a/Marlin/example_configurations/K8200/Configuration.h b/Marlin/example_configurations/K8200/Configuration.h index 220532af31..4c79570bad 100644 --- a/Marlin/example_configurations/K8200/Configuration.h +++ b/Marlin/example_configurations/K8200/Configuration.h @@ -654,9 +654,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //#define DOGLCD // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family) //#define SDSUPPORT // Enable SD Card Support in Hardware Console // Changed behaviour! If you need SDSUPPORT uncomment it! -//#define SDSLOW // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) -//#define SDEXTRASLOW // Use even slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) -//#define SDULTRASLOW // Use slowest SD transfer mode (not normally needed - uncomment if you're getting volume init error) +//#define SPI_SPEED SPI_HALF_SPEED // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) //#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication //#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder //#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking diff --git a/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h b/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h index 9b628d9ff1..df92706ece 100644 --- a/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h +++ b/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h @@ -666,9 +666,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l #define ULTRA_LCD //general LCD support, also 16x2 //#define DOGLCD // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family) #define SDSUPPORT // Enable SD Card Support in Hardware Console -//#define SDSLOW // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) -//#define SDEXTRASLOW // Use even slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) -//#define SDULTRASLOW // Use slowest SD transfer mode (not normally needed - uncomment if you're getting volume init error) +//#define SPI_SPEED SPI_HALF_SPEED // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) #define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication //#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder //#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking diff --git a/Marlin/example_configurations/RigidBot/Configuration.h b/Marlin/example_configurations/RigidBot/Configuration.h index ca1df7fc3e..8ec53268cf 100644 --- a/Marlin/example_configurations/RigidBot/Configuration.h +++ b/Marlin/example_configurations/RigidBot/Configuration.h @@ -658,9 +658,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //#define DOGLCD // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family) #define SDSUPPORT // Enable SD Card Support in Hardware Console // Changed behaviour! If you need SDSUPPORT uncomment it! -//#define SDSLOW // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) -//#define SDEXTRASLOW // Use even slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) -#define SDULTRASLOW // Use slowest SD transfer mode (not normally needed - uncomment if you're getting volume init error) +#define SPI_SPEED SPI_EIGHTH_SPEED // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) //#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication //#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder //#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking diff --git a/Marlin/example_configurations/SCARA/Configuration.h b/Marlin/example_configurations/SCARA/Configuration.h index 881c607656..1cd2600093 100644 --- a/Marlin/example_configurations/SCARA/Configuration.h +++ b/Marlin/example_configurations/SCARA/Configuration.h @@ -674,9 +674,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //#define DOGLCD // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family) //#define SDSUPPORT // Enable SD Card Support in Hardware Console // Changed behaviour! If you need SDSUPPORT uncomment it! -//#define SDSLOW // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) -//#define SDEXTRASLOW // Use even slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) -//#define SDULTRASLOW // Use slowest SD transfer mode (not normally needed - uncomment if you're getting volume init error) +//#define SPI_SPEED SPI_HALF_SPEED // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) //#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication //#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder //#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking diff --git a/Marlin/example_configurations/TAZ4/Configuration.h b/Marlin/example_configurations/TAZ4/Configuration.h index aa839b8b95..55ce81c14a 100644 --- a/Marlin/example_configurations/TAZ4/Configuration.h +++ b/Marlin/example_configurations/TAZ4/Configuration.h @@ -685,9 +685,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //#define DOGLCD // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family) //#define SDSUPPORT // Enable SD Card Support in Hardware Console // Changed behaviour! If you need SDSUPPORT uncomment it! -//#define SDSLOW // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) -//#define SDEXTRASLOW // Use even slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) -//#define SDULTRASLOW // Use slowest SD transfer mode (not normally needed - uncomment if you're getting volume init error) +//#define SPI_SPEED SPI_HALF_SPEED // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) //#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication #define ENCODER_PULSES_PER_STEP 2 // Increase if you have a high resolution encoder #define ENCODER_STEPS_PER_MENU_ITEM 1 // Set according to ENCODER_PULSES_PER_STEP or your liking diff --git a/Marlin/example_configurations/WITBOX/Configuration.h b/Marlin/example_configurations/WITBOX/Configuration.h index 5443f51ee5..03a06cd398 100644 --- a/Marlin/example_configurations/WITBOX/Configuration.h +++ b/Marlin/example_configurations/WITBOX/Configuration.h @@ -657,9 +657,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo #define ULTRA_LCD //general LCD support, also 16x2 //#define DOGLCD // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family) #define SDSUPPORT // Enable SD Card Support in Hardware Console -//#define SDSLOW // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) -//#define SDEXTRASLOW // Use even slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) -//#define SDULTRASLOW // Use slowest SD transfer mode (not normally needed - uncomment if you're getting volume init error) +//#define SPI_SPEED SPI_HALF_SPEED // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) //#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication //#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder //#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking diff --git a/Marlin/example_configurations/adafruit/ST7565/Configuration.h b/Marlin/example_configurations/adafruit/ST7565/Configuration.h index 4032fbdde0..d166fa72b0 100644 --- a/Marlin/example_configurations/adafruit/ST7565/Configuration.h +++ b/Marlin/example_configurations/adafruit/ST7565/Configuration.h @@ -666,9 +666,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //#define ULTRA_LCD //general LCD support, also 16x2 //#define DOGLCD // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family) #define SDSUPPORT // Enable SD Card Support in Hardware Console -#define SDSLOW // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) -//#define SDEXTRASLOW // Use even slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) -//#define SDULTRASLOW // Use slowest SD transfer mode (not normally needed - uncomment if you're getting volume init error) +#define SPI_SPEED SPI_HALF_SPEED // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) //#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication //#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder //#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking diff --git a/Marlin/example_configurations/delta/biv2.5/Configuration.h b/Marlin/example_configurations/delta/biv2.5/Configuration.h index 2289d3d0d4..a7a5e34c2d 100644 --- a/Marlin/example_configurations/delta/biv2.5/Configuration.h +++ b/Marlin/example_configurations/delta/biv2.5/Configuration.h @@ -788,9 +788,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo //#define DOGLCD // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family) //#define SDSUPPORT // Enable SD Card Support in Hardware Console // Changed behaviour! If you need SDSUPPORT uncomment it! -//#define SDSLOW // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) -//#define SDEXTRASLOW // Use even slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) -//#define SDULTRASLOW // Use slowest SD transfer mode (not normally needed - uncomment if you're getting volume init error) +//#define SPI_SPEED SPI_HALF_SPEED // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) //#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication //#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder //#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking diff --git a/Marlin/example_configurations/delta/generic/Configuration.h b/Marlin/example_configurations/delta/generic/Configuration.h index 11e263c81b..6c57a1be70 100644 --- a/Marlin/example_configurations/delta/generic/Configuration.h +++ b/Marlin/example_configurations/delta/generic/Configuration.h @@ -789,9 +789,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo //#define DOGLCD // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family) //#define SDSUPPORT // Enable SD Card Support in Hardware Console // Changed behaviour! If you need SDSUPPORT uncomment it! -//#define SDSLOW // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) -//#define SDEXTRASLOW // Use even slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) -//#define SDULTRASLOW // Use slowest SD transfer mode (not normally needed - uncomment if you're getting volume init error) +//#define SPI_SPEED SPI_HALF_SPEED // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) //#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication //#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder //#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking diff --git a/Marlin/example_configurations/delta/kossel_mini/Configuration.h b/Marlin/example_configurations/delta/kossel_mini/Configuration.h index fe458ed0f7..68cf825628 100644 --- a/Marlin/example_configurations/delta/kossel_mini/Configuration.h +++ b/Marlin/example_configurations/delta/kossel_mini/Configuration.h @@ -793,9 +793,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //#define DOGLCD // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family) //#define SDSUPPORT // Enable SD Card Support in Hardware Console // Changed behaviour! If you need SDSUPPORT uncomment it! -//#define SDSLOW // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) -//#define SDEXTRASLOW // Use even slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) -//#define SDULTRASLOW // Use slowest SD transfer mode (not normally needed - uncomment if you're getting volume init error) +//#define SPI_SPEED SPI_HALF_SPEED // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) //#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication //#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder //#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking diff --git a/Marlin/example_configurations/delta/kossel_pro/Configuration.h b/Marlin/example_configurations/delta/kossel_pro/Configuration.h index e3510fb741..4a3800cbc5 100644 --- a/Marlin/example_configurations/delta/kossel_pro/Configuration.h +++ b/Marlin/example_configurations/delta/kossel_pro/Configuration.h @@ -783,9 +783,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //#define ULTRA_LCD //general LCD support, also 16x2 //#define DOGLCD // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family) #define SDSUPPORT // Enable SD Card Support in Hardware Console -//#define SDSLOW // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) -//#define SDEXTRASLOW // Use even slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) -//#define SDULTRASLOW // Use slowest SD transfer mode (not normally needed - uncomment if you're getting volume init error) +//#define SPI_SPEED SPI_HALF_SPEED // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) //#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication //#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder //#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking diff --git a/Marlin/example_configurations/makibox/Configuration.h b/Marlin/example_configurations/makibox/Configuration.h index c16da81014..5d99544d87 100644 --- a/Marlin/example_configurations/makibox/Configuration.h +++ b/Marlin/example_configurations/makibox/Configuration.h @@ -668,9 +668,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //#define ULTRA_LCD //general LCD support, also 16x2 //#define DOGLCD // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family) #define SDSUPPORT // Enable SD Card Support in Hardware Console -#define SDSLOW // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) -//#define SDEXTRASLOW // Use even slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) -//#define SDULTRASLOW // Use slowest SD transfer mode (not normally needed - uncomment if you're getting volume init error) +#define SPI_SPEED SPI_HALF_SPEED // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) //#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication //#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder //#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking diff --git a/Marlin/example_configurations/tvrrug/Round2/Configuration.h b/Marlin/example_configurations/tvrrug/Round2/Configuration.h index a74d2e51bc..9091073611 100644 --- a/Marlin/example_configurations/tvrrug/Round2/Configuration.h +++ b/Marlin/example_configurations/tvrrug/Round2/Configuration.h @@ -661,9 +661,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo //#define DOGLCD // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family) //#define SDSUPPORT // Enable SD Card Support in Hardware Console // Changed behaviour! If you need SDSUPPORT uncomment it! -//#define SDSLOW // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) -//#define SDEXTRASLOW // Use even slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) -//#define SDULTRASLOW // Use slowest SD transfer mode (not normally needed - uncomment if you're getting volume init error) +//#define SPI_SPEED SPI_HALF_SPEED // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) //#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication //#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder //#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking From 1270fbfd38b4a6589eba563d9cd63d48d56c3aa0 Mon Sep 17 00:00:00 2001 From: Ruwan J Egoda Gamage Date: Thu, 24 Dec 2015 12:12:25 -0500 Subject: [PATCH 6/7] Using SET_INPUT instead of pinMode --- Marlin/ultralcd.cpp | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) diff --git a/Marlin/ultralcd.cpp b/Marlin/ultralcd.cpp index a671a707e3..b8b9769e74 100644 --- a/Marlin/ultralcd.cpp +++ b/Marlin/ultralcd.cpp @@ -1548,10 +1548,10 @@ void lcd_init() { #endif #ifdef RIGIDBOT_PANEL - pinMode(BTN_UP,INPUT); - pinMode(BTN_DWN,INPUT); - pinMode(BTN_LFT,INPUT); - pinMode(BTN_RT,INPUT); + SET_INPUT(BTN_UP); + SET_INPUT(BTN_DWN); + SET_INPUT(BTN_LFT); + SET_INPUT(BTN_RT); #endif #else // Not NEWPANEL From 159ff94afdb6c3def7b1ae583dc3b9a9baf5b746 Mon Sep 17 00:00:00 2001 From: Scott Lahteine Date: Sun, 7 Feb 2016 02:07:21 -0800 Subject: [PATCH 7/7] Remove obsolete HEATER_BED_DUTY_CYCLE_DIVIDER #2977 --- Marlin/Configuration.h | 5 ----- Marlin/configurator/config/Configuration.h | 5 ----- Marlin/example_configurations/Felix/Configuration.h | 5 ----- Marlin/example_configurations/Felix/Configuration_DUAL.h | 5 ----- Marlin/example_configurations/Hephestos/Configuration.h | 5 ----- Marlin/example_configurations/K8200/Configuration.h | 5 ----- .../RepRapWorld/Megatronics/Configuration.h | 5 ----- Marlin/example_configurations/RigidBot/Configuration.h | 5 ----- Marlin/example_configurations/SCARA/Configuration.h | 5 ----- Marlin/example_configurations/TAZ4/Configuration.h | 5 ----- Marlin/example_configurations/WITBOX/Configuration.h | 5 ----- .../example_configurations/adafruit/ST7565/Configuration.h | 5 ----- Marlin/example_configurations/delta/biv2.5/Configuration.h | 5 ----- Marlin/example_configurations/delta/generic/Configuration.h | 5 ----- .../example_configurations/delta/kossel_mini/Configuration.h | 5 ----- .../example_configurations/delta/kossel_pro/Configuration.h | 5 ----- Marlin/example_configurations/makibox/Configuration.h | 5 ----- Marlin/example_configurations/tvrrug/Round2/Configuration.h | 5 ----- 18 files changed, 90 deletions(-) diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h index b7f8f4f1df..61712921fd 100644 --- a/Marlin/Configuration.h +++ b/Marlin/Configuration.h @@ -178,11 +178,6 @@ Here are some standard links for getting your machine calibrated: #define HEATER_3_MAXTEMP 275 #define BED_MAXTEMP 150 -// If your bed has low resistance e.g. .6 ohm and throws the fuse you can duty cycle it to reduce the -// average current. The value should be an integer and the heat bed will be turned on for 1 interval of -// HEATER_BED_DUTY_CYCLE_DIVIDER intervals. -//#define HEATER_BED_DUTY_CYCLE_DIVIDER 4 - // If you want the M105 heater power reported in watts, define the BED_WATTS, and (shared for all extruders) EXTRUDER_WATTS //#define EXTRUDER_WATTS (12.0*12.0/6.7) // P=I^2/R //#define BED_WATTS (12.0*12.0/1.1) // P=I^2/R diff --git a/Marlin/configurator/config/Configuration.h b/Marlin/configurator/config/Configuration.h index 3d00134fb0..2ffe574181 100644 --- a/Marlin/configurator/config/Configuration.h +++ b/Marlin/configurator/config/Configuration.h @@ -178,11 +178,6 @@ Here are some standard links for getting your machine calibrated: #define HEATER_3_MAXTEMP 275 #define BED_MAXTEMP 150 -// If your bed has low resistance e.g. .6 ohm and throws the fuse you can duty cycle it to reduce the -// average current. The value should be an integer and the heat bed will be turned on for 1 interval of -// HEATER_BED_DUTY_CYCLE_DIVIDER intervals. -//#define HEATER_BED_DUTY_CYCLE_DIVIDER 4 - // If you want the M105 heater power reported in watts, define the BED_WATTS, and (shared for all extruders) EXTRUDER_WATTS //#define EXTRUDER_WATTS (12.0*12.0/6.7) // P=I^2/R //#define BED_WATTS (12.0*12.0/1.1) // P=I^2/R diff --git a/Marlin/example_configurations/Felix/Configuration.h b/Marlin/example_configurations/Felix/Configuration.h index 0d1eb86460..eda6e5e01e 100644 --- a/Marlin/example_configurations/Felix/Configuration.h +++ b/Marlin/example_configurations/Felix/Configuration.h @@ -178,11 +178,6 @@ Here are some standard links for getting your machine calibrated: #define HEATER_3_MAXTEMP 275 #define BED_MAXTEMP 150 -// If your bed has low resistance e.g. .6 ohm and throws the fuse you can duty cycle it to reduce the -// average current. The value should be an integer and the heat bed will be turned on for 1 interval of -// HEATER_BED_DUTY_CYCLE_DIVIDER intervals. -//#define HEATER_BED_DUTY_CYCLE_DIVIDER 4 - // If you want the M105 heater power reported in watts, define the BED_WATTS, and (shared for all extruders) EXTRUDER_WATTS //#define EXTRUDER_WATTS (12.0*12.0/6.7) // P=I^2/R //#define BED_WATTS (12.0*12.0/1.1) // P=I^2/R diff --git a/Marlin/example_configurations/Felix/Configuration_DUAL.h b/Marlin/example_configurations/Felix/Configuration_DUAL.h index d91caae685..160e844267 100644 --- a/Marlin/example_configurations/Felix/Configuration_DUAL.h +++ b/Marlin/example_configurations/Felix/Configuration_DUAL.h @@ -167,11 +167,6 @@ Here are some standard links for getting your machine calibrated: #define HEATER_3_MAXTEMP 275 #define BED_MAXTEMP 150 -// If your bed has low resistance e.g. .6 ohm and throws the fuse you can duty cycle it to reduce the -// average current. The value should be an integer and the heat bed will be turned on for 1 interval of -// HEATER_BED_DUTY_CYCLE_DIVIDER intervals. -//#define HEATER_BED_DUTY_CYCLE_DIVIDER 4 - // If you want the M105 heater power reported in watts, define the BED_WATTS, and (shared for all extruders) EXTRUDER_WATTS //#define EXTRUDER_WATTS (12.0*12.0/6.7) // P=I^2/R //#define BED_WATTS (12.0*12.0/1.1) // P=I^2/R diff --git a/Marlin/example_configurations/Hephestos/Configuration.h b/Marlin/example_configurations/Hephestos/Configuration.h index 10950b27bc..b86df6aff7 100644 --- a/Marlin/example_configurations/Hephestos/Configuration.h +++ b/Marlin/example_configurations/Hephestos/Configuration.h @@ -181,11 +181,6 @@ Here are some standard links for getting your machine calibrated: #define HEATER_3_MAXTEMP 260 #define BED_MAXTEMP 150 -// If your bed has low resistance e.g. .6 ohm and throws the fuse you can duty cycle it to reduce the -// average current. The value should be an integer and the heat bed will be turned on for 1 interval of -// HEATER_BED_DUTY_CYCLE_DIVIDER intervals. -//#define HEATER_BED_DUTY_CYCLE_DIVIDER 4 - // If you want the M105 heater power reported in watts, define the BED_WATTS, and (shared for all extruders) EXTRUDER_WATTS //#define EXTRUDER_WATTS (12.0*12.0/6.7) // P=I^2/R //#define BED_WATTS (12.0*12.0/1.1) // P=I^2/R diff --git a/Marlin/example_configurations/K8200/Configuration.h b/Marlin/example_configurations/K8200/Configuration.h index 4c79570bad..ba61cb52b1 100644 --- a/Marlin/example_configurations/K8200/Configuration.h +++ b/Marlin/example_configurations/K8200/Configuration.h @@ -183,11 +183,6 @@ Here are some standard links for getting your machine calibrated: #define HEATER_3_MAXTEMP 275 #define BED_MAXTEMP 150 -// If your bed has low resistance e.g. .6 ohm and throws the fuse you can duty cycle it to reduce the -// average current. The value should be an integer and the heat bed will be turned on for 1 interval of -// HEATER_BED_DUTY_CYCLE_DIVIDER intervals. -//#define HEATER_BED_DUTY_CYCLE_DIVIDER 4 - // If you want the M105 heater power reported in watts, define the BED_WATTS, and (shared for all extruders) EXTRUDER_WATTS //#define EXTRUDER_WATTS (12.0*12.0/6.7) // P=I^2/R //#define BED_WATTS (12.0*12.0/1.1) // P=I^2/R diff --git a/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h b/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h index df92706ece..7524af5cfd 100644 --- a/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h +++ b/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h @@ -178,11 +178,6 @@ Here are some standard links for getting your machine calibrated: #define HEATER_3_MAXTEMP 275 #define BED_MAXTEMP 150 -// If your bed has low resistance e.g. .6 ohm and throws the fuse you can duty cycle it to reduce the -// average current. The value should be an integer and the heat bed will be turned on for 1 interval of -// HEATER_BED_DUTY_CYCLE_DIVIDER intervals. -//#define HEATER_BED_DUTY_CYCLE_DIVIDER 4 - // If you want the M105 heater power reported in watts, define the BED_WATTS, and (shared for all extruders) EXTRUDER_WATTS //#define EXTRUDER_WATTS (12.0*12.0/6.7) // P=I^2/R //#define BED_WATTS (12.0*12.0/1.1) // P=I^2/R diff --git a/Marlin/example_configurations/RigidBot/Configuration.h b/Marlin/example_configurations/RigidBot/Configuration.h index 8ec53268cf..bcbc7219b9 100644 --- a/Marlin/example_configurations/RigidBot/Configuration.h +++ b/Marlin/example_configurations/RigidBot/Configuration.h @@ -178,11 +178,6 @@ Here are some standard links for getting your machine calibrated: #define HEATER_3_MAXTEMP 275 #define BED_MAXTEMP 150 -// If your bed has low resistance e.g. .6 ohm and throws the fuse you can duty cycle it to reduce the -// average current. The value should be an integer and the heat bed will be turned on for 1 interval of -// HEATER_BED_DUTY_CYCLE_DIVIDER intervals. -//#define HEATER_BED_DUTY_CYCLE_DIVIDER 4 - // If you want the M105 heater power reported in watts, define the BED_WATTS, and (shared for all extruders) EXTRUDER_WATTS //#define EXTRUDER_WATTS (12.0*12.0/6.7) // P=I^2/R //#define BED_WATTS (12.0*12.0/1.1) // P=I^2/R diff --git a/Marlin/example_configurations/SCARA/Configuration.h b/Marlin/example_configurations/SCARA/Configuration.h index 1cd2600093..957568d4ce 100644 --- a/Marlin/example_configurations/SCARA/Configuration.h +++ b/Marlin/example_configurations/SCARA/Configuration.h @@ -203,11 +203,6 @@ Here are some standard links for getting your machine calibrated: #define HEATER_3_MAXTEMP 275 #define BED_MAXTEMP 150 -// If your bed has low resistance e.g. .6 ohm and throws the fuse you can duty cycle it to reduce the -// average current. The value should be an integer and the heat bed will be turned on for 1 interval of -// HEATER_BED_DUTY_CYCLE_DIVIDER intervals. -//#define HEATER_BED_DUTY_CYCLE_DIVIDER 4 - // If you want the M105 heater power reported in watts, define the BED_WATTS, and (shared for all extruders) EXTRUDER_WATTS #define EXTRUDER_WATTS (2*2/5.9) // P=I^2/R #define BED_WATTS (5.45*5.45/2.2) // P=I^2/R diff --git a/Marlin/example_configurations/TAZ4/Configuration.h b/Marlin/example_configurations/TAZ4/Configuration.h index 55ce81c14a..b216277aae 100644 --- a/Marlin/example_configurations/TAZ4/Configuration.h +++ b/Marlin/example_configurations/TAZ4/Configuration.h @@ -178,11 +178,6 @@ Here are some standard links for getting your machine calibrated: #define HEATER_3_MAXTEMP 250 #define BED_MAXTEMP 150 -// If your bed has low resistance e.g. .6 ohm and throws the fuse you can duty cycle it to reduce the -// average current. The value should be an integer and the heat bed will be turned on for 1 interval of -// HEATER_BED_DUTY_CYCLE_DIVIDER intervals. -//#define HEATER_BED_DUTY_CYCLE_DIVIDER 4 - // If you want the M105 heater power reported in watts, define the BED_WATTS, and (shared for all extruders) EXTRUDER_WATTS //#define EXTRUDER_WATTS (12.0*12.0/6.7) // P=I^2/R //#define BED_WATTS (12.0*12.0/1.1) // P=I^2/R diff --git a/Marlin/example_configurations/WITBOX/Configuration.h b/Marlin/example_configurations/WITBOX/Configuration.h index 03a06cd398..9b7859348d 100644 --- a/Marlin/example_configurations/WITBOX/Configuration.h +++ b/Marlin/example_configurations/WITBOX/Configuration.h @@ -181,11 +181,6 @@ Here are some standard links for getting your machine calibrated: #define HEATER_3_MAXTEMP 260 #define BED_MAXTEMP 150 -// If your bed has low resistance e.g. .6 ohm and throws the fuse you can duty cycle it to reduce the -// average current. The value should be an integer and the heat bed will be turned on for 1 interval of -// HEATER_BED_DUTY_CYCLE_DIVIDER intervals. -//#define HEATER_BED_DUTY_CYCLE_DIVIDER 4 - // If you want the M105 heater power reported in watts, define the BED_WATTS, and (shared for all extruders) EXTRUDER_WATTS //#define EXTRUDER_WATTS (12.0*12.0/6.7) // P=I^2/R //#define BED_WATTS (12.0*12.0/1.1) // P=I^2/R diff --git a/Marlin/example_configurations/adafruit/ST7565/Configuration.h b/Marlin/example_configurations/adafruit/ST7565/Configuration.h index d166fa72b0..72f4396210 100644 --- a/Marlin/example_configurations/adafruit/ST7565/Configuration.h +++ b/Marlin/example_configurations/adafruit/ST7565/Configuration.h @@ -178,11 +178,6 @@ Here are some standard links for getting your machine calibrated: #define HEATER_3_MAXTEMP 275 #define BED_MAXTEMP 150 -// If your bed has low resistance e.g. .6 ohm and throws the fuse you can duty cycle it to reduce the -// average current. The value should be an integer and the heat bed will be turned on for 1 interval of -// HEATER_BED_DUTY_CYCLE_DIVIDER intervals. -//#define HEATER_BED_DUTY_CYCLE_DIVIDER 4 - // If you want the M105 heater power reported in watts, define the BED_WATTS, and (shared for all extruders) EXTRUDER_WATTS //#define EXTRUDER_WATTS (12.0*12.0/6.7) // P=I^2/R //#define BED_WATTS (12.0*12.0/1.1) // P=I^2/R diff --git a/Marlin/example_configurations/delta/biv2.5/Configuration.h b/Marlin/example_configurations/delta/biv2.5/Configuration.h index a7a5e34c2d..509dc971d9 100644 --- a/Marlin/example_configurations/delta/biv2.5/Configuration.h +++ b/Marlin/example_configurations/delta/biv2.5/Configuration.h @@ -178,11 +178,6 @@ Here are some standard links for getting your machine calibrated: #define HEATER_3_MAXTEMP 275 #define BED_MAXTEMP 150 -// If your bed has low resistance e.g. .6 ohm and throws the fuse you can duty cycle it to reduce the -// average current. The value should be an integer and the heat bed will be turned on for 1 interval of -// HEATER_BED_DUTY_CYCLE_DIVIDER intervals. -//#define HEATER_BED_DUTY_CYCLE_DIVIDER 4 - // If you want the M105 heater power reported in watts, define the BED_WATTS, and (shared for all extruders) EXTRUDER_WATTS //#define EXTRUDER_WATTS (12.0*12.0/6.7) // P=I^2/R //#define BED_WATTS (12.0*12.0/1.1) // P=I^2/R diff --git a/Marlin/example_configurations/delta/generic/Configuration.h b/Marlin/example_configurations/delta/generic/Configuration.h index 6c57a1be70..f38a63b171 100644 --- a/Marlin/example_configurations/delta/generic/Configuration.h +++ b/Marlin/example_configurations/delta/generic/Configuration.h @@ -178,11 +178,6 @@ Here are some standard links for getting your machine calibrated: #define HEATER_3_MAXTEMP 275 #define BED_MAXTEMP 150 -// If your bed has low resistance e.g. .6 ohm and throws the fuse you can duty cycle it to reduce the -// average current. The value should be an integer and the heat bed will be turned on for 1 interval of -// HEATER_BED_DUTY_CYCLE_DIVIDER intervals. -//#define HEATER_BED_DUTY_CYCLE_DIVIDER 4 - // If you want the M105 heater power reported in watts, define the BED_WATTS, and (shared for all extruders) EXTRUDER_WATTS //#define EXTRUDER_WATTS (12.0*12.0/6.7) // P=I^2/R //#define BED_WATTS (12.0*12.0/1.1) // P=I^2/R diff --git a/Marlin/example_configurations/delta/kossel_mini/Configuration.h b/Marlin/example_configurations/delta/kossel_mini/Configuration.h index 68cf825628..6d017494a4 100644 --- a/Marlin/example_configurations/delta/kossel_mini/Configuration.h +++ b/Marlin/example_configurations/delta/kossel_mini/Configuration.h @@ -178,11 +178,6 @@ Here are some standard links for getting your machine calibrated: #define HEATER_3_MAXTEMP 275 #define BED_MAXTEMP 150 -// If your bed has low resistance e.g. .6 ohm and throws the fuse you can duty cycle it to reduce the -// average current. The value should be an integer and the heat bed will be turned on for 1 interval of -// HEATER_BED_DUTY_CYCLE_DIVIDER intervals. -//#define HEATER_BED_DUTY_CYCLE_DIVIDER 4 - // If you want the M105 heater power reported in watts, define the BED_WATTS, and (shared for all extruders) EXTRUDER_WATTS //#define EXTRUDER_WATTS (12.0*12.0/6.7) // P=I^2/R //#define BED_WATTS (12.0*12.0/1.1) // P=I^2/R diff --git a/Marlin/example_configurations/delta/kossel_pro/Configuration.h b/Marlin/example_configurations/delta/kossel_pro/Configuration.h index 4a3800cbc5..c8077ad1cb 100644 --- a/Marlin/example_configurations/delta/kossel_pro/Configuration.h +++ b/Marlin/example_configurations/delta/kossel_pro/Configuration.h @@ -182,11 +182,6 @@ Here are some standard links for getting your machine calibrated: #define HEATER_3_MAXTEMP 275 #define BED_MAXTEMP 150 -// If your bed has low resistance e.g. .6 ohm and throws the fuse you can duty cycle it to reduce the -// average current. The value should be an integer and the heat bed will be turned on for 1 interval of -// HEATER_BED_DUTY_CYCLE_DIVIDER intervals. -//#define HEATER_BED_DUTY_CYCLE_DIVIDER 4 - // If you want the M105 heater power reported in watts, define the BED_WATTS, and (shared for all extruders) EXTRUDER_WATTS //#define EXTRUDER_WATTS (12.0*12.0/6.7) // P=I^2/R //#define BED_WATTS (12.0*12.0/1.1) // P=I^2/R diff --git a/Marlin/example_configurations/makibox/Configuration.h b/Marlin/example_configurations/makibox/Configuration.h index 5d99544d87..080abb2c5f 100644 --- a/Marlin/example_configurations/makibox/Configuration.h +++ b/Marlin/example_configurations/makibox/Configuration.h @@ -178,11 +178,6 @@ Here are some standard links for getting your machine calibrated: #define HEATER_3_MAXTEMP 275 #define BED_MAXTEMP 150 -// If your bed has low resistance e.g. .6 ohm and throws the fuse you can duty cycle it to reduce the -// average current. The value should be an integer and the heat bed will be turned on for 1 interval of -// HEATER_BED_DUTY_CYCLE_DIVIDER intervals. -//#define HEATER_BED_DUTY_CYCLE_DIVIDER 4 - // If you want the M105 heater power reported in watts, define the BED_WATTS, and (shared for all extruders) EXTRUDER_WATTS //#define EXTRUDER_WATTS (12.0*12.0/6.7) // P=I^2/R //#define BED_WATTS (12.0*12.0/1.1) // P=I^2/R diff --git a/Marlin/example_configurations/tvrrug/Round2/Configuration.h b/Marlin/example_configurations/tvrrug/Round2/Configuration.h index 9091073611..80cf1d1a40 100644 --- a/Marlin/example_configurations/tvrrug/Round2/Configuration.h +++ b/Marlin/example_configurations/tvrrug/Round2/Configuration.h @@ -178,11 +178,6 @@ Here are some standard links for getting your machine calibrated: #define HEATER_3_MAXTEMP 275 #define BED_MAXTEMP 150 -// If your bed has low resistance e.g. .6 ohm and throws the fuse you can duty cycle it to reduce the -// average current. The value should be an integer and the heat bed will be turned on for 1 interval of -// HEATER_BED_DUTY_CYCLE_DIVIDER intervals. -//#define HEATER_BED_DUTY_CYCLE_DIVIDER 4 - // If you want the M105 heater power reported in watts, define the BED_WATTS, and (shared for all extruders) EXTRUDER_WATTS //#define EXTRUDER_WATTS (12.0*12.0/6.7) // P=I^2/R //#define BED_WATTS (12.0*12.0/1.1) // P=I^2/R