Browse Source

Fix STM32F1 SPI device init, MKS_LCD12864 (#19271)

vanilla_fb_2.0.x
Victor Oliveira 4 years ago
committed by Scott Lahteine
parent
commit
24fbfae0fd
  1. 5
      Marlin/src/HAL/STM32F1/SPI.cpp
  2. 1
      Marlin/src/lcd/dogm/u8g_dev_uc1701_mini12864_HAL.cpp
  3. 60
      Marlin/src/lcd/dogm/ultralcd_DOGM.cpp
  4. 3
      Marlin/src/pins/stm32f1/pins_MKS_ROBIN_E3_common.h
  5. 2
      Marlin/src/pins/stm32f1/pins_MKS_ROBIN_LITE3.h
  6. 4
      Marlin/src/pins/stm32f1/pins_MKS_ROBIN_NANO_V2.h

5
Marlin/src/HAL/STM32F1/SPI.cpp

@ -40,6 +40,9 @@
#include <boards.h>
#include <wirish.h>
#include "../../inc/MarlinConfig.h"
#include "spi_pins.h"
/** Time in ms for DMA receive timeout */
#define DMA_TIMEOUT 100
@ -710,6 +713,6 @@ static spi_baud_rate determine_baud_rate(spi_dev *dev, uint32_t freq) {
return baud_rates[i];
}
SPIClass SPI(1);
SPIClass SPI(SPI_DEVICE);
#endif // __STM32F1__

1
Marlin/src/lcd/dogm/u8g_dev_uc1701_mini12864_HAL.cpp

@ -112,6 +112,7 @@ static const uint8_t u8g_dev_uc1701_mini12864_HAL_init_seq[] PROGMEM = {
U8G_ESC_CS(1), // enable chip
UC1701_ALL_PIX(0), // normal display
U8G_ESC_CS(0), // disable chip
U8G_ESC_DLY(150), // delay 150 ms before sending any data
U8G_ESC_END // end of sequence
};

60
Marlin/src/lcd/dogm/ultralcd_DOGM.cpp

@ -240,39 +240,35 @@ bool MarlinUI::detected() { return true; }
// Initialize or re-initialize the LCD
void MarlinUI::init_lcd() {
#if DISABLED(MKS_LCD12864)
#if PIN_EXISTS(LCD_BACKLIGHT)
OUT_WRITE(LCD_BACKLIGHT_PIN, DISABLED(DELAYED_BACKLIGHT_INIT)); // Illuminate after reset or right away
#endif
#if ANY(MKS_12864OLED, MKS_12864OLED_SSD1306, FYSETC_242_OLED_12864, ZONESTAR_12864OLED)
SET_OUTPUT(LCD_PINS_DC);
#ifndef LCD_RESET_PIN
#define LCD_RESET_PIN LCD_PINS_RS
#endif
#endif
#if PIN_EXISTS(LCD_RESET)
// Perform a clean hardware reset with needed delays
OUT_WRITE(LCD_RESET_PIN, LOW);
_delay_ms(5);
WRITE(LCD_RESET_PIN, HIGH);
_delay_ms(5);
u8g.begin();
#if PIN_EXISTS(LCD_BACKLIGHT)
OUT_WRITE(LCD_BACKLIGHT_PIN, DISABLED(DELAYED_BACKLIGHT_INIT)); // Illuminate after reset or right away
#endif
#if ANY(MKS_12864OLED, MKS_12864OLED_SSD1306, FYSETC_242_OLED_12864, ZONESTAR_12864OLED)
SET_OUTPUT(LCD_PINS_DC);
#ifndef LCD_RESET_PIN
#define LCD_RESET_PIN LCD_PINS_RS
#endif
#if PIN_EXISTS(LCD_BACKLIGHT) && ENABLED(DELAYED_BACKLIGHT_INIT)
WRITE(LCD_BACKLIGHT_PIN, HIGH);
#endif
TERN_(HAS_LCD_CONTRAST, refresh_contrast());
TERN_(LCD_SCREEN_ROT_90, u8g.setRot90());
TERN_(LCD_SCREEN_ROT_180, u8g.setRot180());
TERN_(LCD_SCREEN_ROT_270, u8g.setRot270());
#endif // !MKS_LCD12864
#endif
#if PIN_EXISTS(LCD_RESET)
// Perform a clean hardware reset with needed delays
OUT_WRITE(LCD_RESET_PIN, LOW);
_delay_ms(5);
WRITE(LCD_RESET_PIN, HIGH);
_delay_ms(5);
u8g.begin();
#endif
#if PIN_EXISTS(LCD_BACKLIGHT) && ENABLED(DELAYED_BACKLIGHT_INIT)
WRITE(LCD_BACKLIGHT_PIN, HIGH);
#endif
TERN_(HAS_LCD_CONTRAST, refresh_contrast());
TERN_(LCD_SCREEN_ROT_90, u8g.setRot90());
TERN_(LCD_SCREEN_ROT_180, u8g.setRot180());
TERN_(LCD_SCREEN_ROT_270, u8g.setRot270());
uxg_SetUtf8Fonts(g_fontinfo, COUNT(g_fontinfo));
}

3
Marlin/src/pins/stm32f1/pins_MKS_ROBIN_E3_common.h

@ -33,7 +33,6 @@
//#define DISABLE_DEBUG
#define DISABLE_JTAG
#define ENABLE_SPI2
//
// EEPROM
@ -152,8 +151,6 @@
#define DOGLCD_SCK PB13
#define DOGLCD_MOSI PB15
#undef SHOW_BOOTSCREEN
#else
#define LCD_PINS_D4 PA6

2
Marlin/src/pins/stm32f1/pins_MKS_ROBIN_LITE3.h

@ -115,8 +115,6 @@
#define DOGLCD_SCK PB13
#define DOGLCD_MOSI PB15
#undef SHOW_BOOTSCREEN
#else // !MKS_MINI_12864
#define LCD_PINS_D4 PA6

4
Marlin/src/pins/stm32f1/pins_MKS_ROBIN_NANO_V2.h

@ -351,10 +351,6 @@
#define DOGLCD_SCK PA5
#define DOGLCD_MOSI PA7
// Required for MKS_MINI_12864 with this board
#define MKS_LCD12864B
#undef SHOW_BOOTSCREEN
#else // !MKS_MINI_12864
#define LCD_PINS_D4 PE14

Loading…
Cancel
Save