Merge pull request #8667 from Wackerbarth/PID_on_bed_only

[2.0.x] Compilation errors with PIDTEMPBED only

Marlin/Configuration.h

@@ -339,8 +339,9 @@
 
 // Comment the following line to disable PID and enable bang-bang.
 #define PIDTEMP
-#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
+#define BANG_MAX 255     // Limits current to nozzle while in bang-bang mode; 255=full current
-#define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_K1 0.95      // Smoothing factor within any PID loop
 #if ENABLED(PIDTEMP)
   //#define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
   //#define PID_DEBUG // Sends debug data to the serial port.
@@ -350,7 +351,6 @@
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
-  #define K1 0.95 //smoothing factor within the PID
 
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 

Marlin/src/config/default/Configuration.h

@@ -339,8 +339,9 @@
 
 // Comment the following line to disable PID and enable bang-bang.
 #define PIDTEMP
-#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
+#define BANG_MAX 255     // Limits current to nozzle while in bang-bang mode; 255=full current
-#define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_K1 0.95      // Smoothing factor within any PID loop
 #if ENABLED(PIDTEMP)
   //#define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
   //#define PID_DEBUG // Sends debug data to the serial port.
@@ -350,7 +351,6 @@
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
-  #define K1 0.95 //smoothing factor within the PID
 
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 

Marlin/src/config/examples/AlephObjects/TAZ4/Configuration.h

@@ -339,8 +339,9 @@
 
 // Comment the following line to disable PID and enable bang-bang.
 #define PIDTEMP
-#define BANG_MAX 70 // limits current to nozzle while in bang-bang mode; 255=full current
+#define BANG_MAX 70      // Limits current to nozzle while in bang-bang mode; 255=full current
-#define PID_MAX 74 // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_MAX  74      // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_K1 0.95      // Smoothing factor within any PID loop
 #if ENABLED(PIDTEMP)
   //#define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
   //#define PID_DEBUG // Sends debug data to the serial port.
@@ -350,7 +351,6 @@
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
   #define PID_FUNCTIONAL_RANGE 16 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
-  #define K1 0.95 //smoothing factor within the PID
 
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
   // Buda 2.0 on 24V

Marlin/src/config/examples/AliExpress/CL-260/Configuration.h

@@ -339,8 +339,9 @@
 
 // Comment the following line to disable PID and enable bang-bang.
 #define PIDTEMP
-#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
+#define BANG_MAX 255     // Limits current to nozzle while in bang-bang mode; 255=full current
-#define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_K1 0.95      // Smoothing factor within any PID loop
 #if ENABLED(PIDTEMP)
   //#define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
   //#define PID_DEBUG // Sends debug data to the serial port.
@@ -350,7 +351,6 @@
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
-  #define K1 0.95 //smoothing factor within the PID
 
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 

Marlin/src/config/examples/Anet/A6/Configuration.h

@@ -339,8 +339,9 @@
 
 // Comment the following line to disable PID and enable bang-bang.
 #define PIDTEMP
-#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
+#define BANG_MAX 255     // Limits current to nozzle while in bang-bang mode; 255=full current
-#define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_K1 0.95      // Smoothing factor within any PID loop
 #if ENABLED(PIDTEMP)
   //#define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
   //#define PID_DEBUG // Sends debug data to the serial port.
@@ -350,7 +351,6 @@
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
-  #define K1 0.95 //smoothing factor within the PID
 
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 

Marlin/src/config/examples/Anet/A8/Configuration.h

@@ -339,8 +339,9 @@
 
 // Comment the following line to disable PID and enable bang-bang.
 #define PIDTEMP
-#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
+#define BANG_MAX 255     // Limits current to nozzle while in bang-bang mode; 255=full current
-#define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_K1 0.95      // Smoothing factor within any PID loop
 #if ENABLED(PIDTEMP)
   //#define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
   //#define PID_DEBUG // Sends debug data to the serial port.
@@ -350,7 +351,6 @@
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
   #define PID_FUNCTIONAL_RANGE 15 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
-  #define K1 0.95 //smoothing factor within the PID
 
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 

Marlin/src/config/examples/Azteeg/X5GT/Configuration.h

@@ -339,8 +339,9 @@
 
 // Comment the following line to disable PID and enable bang-bang.
 #define PIDTEMP
-#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
+#define BANG_MAX 255     // Limits current to nozzle while in bang-bang mode; 255=full current
-#define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_K1 0.95      // Smoothing factor within any PID loop
 #if ENABLED(PIDTEMP)
   //#define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
   //#define PID_DEBUG // Sends debug data to the serial port.
@@ -350,7 +351,6 @@
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
-  #define K1 0.95 //smoothing factor within the PID
 
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 

Marlin/src/config/examples/BQ/Hephestos/Configuration.h

@@ -342,8 +342,9 @@
 
 // Comment the following line to disable PID and enable bang-bang.
 #define PIDTEMP
-#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
+#define BANG_MAX 255     // Limits current to nozzle while in bang-bang mode; 255=full current
-#define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_K1 0.95      // Smoothing factor within any PID loop
 #if ENABLED(PIDTEMP)
   //#define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
   //#define PID_DEBUG // Sends debug data to the serial port.
@@ -353,7 +354,6 @@
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
-  #define K1 0.95 //smoothing factor within the PID
 
   // Hephestos i3
   #define  DEFAULT_Kp 23.05

Marlin/src/config/examples/BQ/Hephestos_2/Configuration.h

@@ -344,8 +344,9 @@
 
 // Comment the following line to disable PID and enable bang-bang.
 #define PIDTEMP
-#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
+#define BANG_MAX 255     // Limits current to nozzle while in bang-bang mode; 255=full current
-#define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_K1 0.95      // Smoothing factor within any PID loop
 #if ENABLED(PIDTEMP)
   //#define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
   //#define PID_DEBUG // Sends debug data to the serial port.
@@ -355,7 +356,6 @@
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
   #define PID_FUNCTIONAL_RANGE 50 // If the temperature difference between the target temperature and the actual temperature
                                     // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
-  #define K1 0.95 //smoothing factor within the PID
 
   // Tuned PID values using M303
   #define  DEFAULT_Kp 19.18

Marlin/src/config/examples/BQ/WITBOX/Configuration.h

@@ -342,8 +342,9 @@
 
 // Comment the following line to disable PID and enable bang-bang.
 #define PIDTEMP
-#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
+#define BANG_MAX 255     // Limits current to nozzle while in bang-bang mode; 255=full current
-#define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_K1 0.95      // Smoothing factor within any PID loop
 #if ENABLED(PIDTEMP)
   //#define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
   //#define PID_DEBUG // Sends debug data to the serial port.
@@ -353,7 +354,6 @@
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
-  #define K1 0.95 //smoothing factor within the PID
 
   // Witbox
   #define  DEFAULT_Kp 22.2

Marlin/src/config/examples/Cartesio/Configuration.h

@@ -340,8 +340,9 @@
 
 // Comment the following line to disable PID and enable bang-bang.
 #define PIDTEMP
-#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
+#define BANG_MAX 255     // Limits current to nozzle while in bang-bang mode; 255=full current
-#define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_K1 0.95      // Smoothing factor within any PID loop
 #if ENABLED(PIDTEMP)
   //#define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
   //#define PID_DEBUG // Sends debug data to the serial port.
@@ -351,7 +352,6 @@
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
-  #define K1 0.95 //smoothing factor within the PID
 
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 

Marlin/src/config/examples/Creality/CR-10/Configuration.h

@@ -339,8 +339,9 @@
 
 // Comment the following line to disable PID and enable bang-bang.
 #define PIDTEMP
-#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
+#define BANG_MAX 255     // Limits current to nozzle while in bang-bang mode; 255=full current
-#define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_K1 0.95      // Smoothing factor within any PID loop
 #if ENABLED(PIDTEMP)
   //#define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
   //#define PID_DEBUG // Sends debug data to the serial port.
@@ -350,7 +351,6 @@
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
-  #define K1 0.95 //smoothing factor within the PID
 
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 

Marlin/src/config/examples/Felix/Configuration.h

@@ -339,8 +339,9 @@
 
 // Comment the following line to disable PID and enable bang-bang.
 #define PIDTEMP
-#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
+#define BANG_MAX 255     // Limits current to nozzle while in bang-bang mode; 255=full current
-#define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_K1 0.95      // Smoothing factor within any PID loop
 #if ENABLED(PIDTEMP)
   //#define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
   //#define PID_DEBUG // Sends debug data to the serial port.
@@ -350,7 +351,6 @@
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
-  #define K1 0.95 //smoothing factor within the PID
 
   // Felix 2.0+ electronics with v4 Hotend
   #define DEFAULT_Kp 12

Marlin/src/config/examples/Felix/DUAL/Configuration.h

@@ -339,8 +339,9 @@
 
 // Comment the following line to disable PID and enable bang-bang.
 #define PIDTEMP
-#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
+#define BANG_MAX 255     // Limits current to nozzle while in bang-bang mode; 255=full current
-#define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_K1 0.95      // Smoothing factor within any PID loop
 #if ENABLED(PIDTEMP)
   //#define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
   //#define PID_DEBUG // Sends debug data to the serial port.
@@ -350,7 +351,6 @@
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
-  #define K1 0.95 //smoothing factor within the PID
 
   // Felix 2.0+ electronics with v4 Hotend
   #define DEFAULT_Kp 12

Marlin/src/config/examples/FolgerTech/i3-2020/Configuration.h

@@ -340,8 +340,9 @@
 
 // Comment the following line to disable PID and enable bang-bang.
 #define PIDTEMP
-#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
+#define BANG_MAX 255     // Limits current to nozzle while in bang-bang mode; 255=full current
-#define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_K1 0.95      // Smoothing factor within any PID loop
 #if ENABLED(PIDTEMP)
   //#define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
   //#define PID_DEBUG // Sends debug data to the serial port.
@@ -351,7 +352,6 @@
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
-  #define K1 0.95 //smoothing factor within the PID
 
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 

Marlin/src/config/examples/Geeetech/GT2560/Configuration.h

@@ -339,8 +339,9 @@
 
 // Comment the following line to disable PID and enable bang-bang.
 #define PIDTEMP
-#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
+#define BANG_MAX 255     // Limits current to nozzle while in bang-bang mode; 255=full current
-#define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_K1 0.95      // Smoothing factor within any PID loop
 #if ENABLED(PIDTEMP)
   //#define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
   //#define PID_DEBUG // Sends debug data to the serial port.
@@ -350,7 +351,6 @@
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
-  #define K1 0.95 //smoothing factor within the PID
 
   // Geeetech MK8 Extruder
   #define  DEFAULT_Kp 12.33

Marlin/src/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h

@@ -339,8 +339,9 @@
 
 // Comment the following line to disable PID and enable bang-bang.
 #define PIDTEMP
-#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
+#define BANG_MAX 255     // Limits current to nozzle while in bang-bang mode; 255=full current
-#define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_K1 0.95      // Smoothing factor within any PID loop
 #if ENABLED(PIDTEMP)
   //#define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
   //#define PID_DEBUG // Sends debug data to the serial port.
@@ -350,7 +351,6 @@
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
-  #define K1 0.95 //smoothing factor within the PID
 
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 

Marlin/src/config/examples/Infitary/i3-M508/Configuration.h

@@ -339,8 +339,9 @@
 
 // Comment the following line to disable PID and enable bang-bang.
 #define PIDTEMP
-#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
+#define BANG_MAX 255     // Limits current to nozzle while in bang-bang mode; 255=full current
-#define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_K1 0.95      // Smoothing factor within any PID loop
 #if ENABLED(PIDTEMP)
   //#define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
   //#define PID_DEBUG // Sends debug data to the serial port.
@@ -350,7 +351,6 @@
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
-  #define K1 0.95 //smoothing factor within the PID
 
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 

Marlin/src/config/examples/Malyan/M150/Configuration.h

@@ -347,8 +347,9 @@
 
 // Comment the following line to disable PID and enable bang-bang.
 #define PIDTEMP
-#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
+#define BANG_MAX 255     // Limits current to nozzle while in bang-bang mode; 255=full current
-#define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_K1 0.95      // Smoothing factor within any PID loop
 #if ENABLED(PIDTEMP)
   //#define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
   //#define PID_DEBUG // Sends debug data to the serial port.
@@ -358,7 +359,6 @@
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
-  #define K1 0.95 //smoothing factor within the PID
 
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 

Marlin/src/config/examples/Micromake/C1/basic/Configuration.h

@@ -339,8 +339,9 @@
 
 // Comment the following line to disable PID and enable bang-bang.
 #define PIDTEMP
-#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
+#define BANG_MAX 255     // Limits current to nozzle while in bang-bang mode; 255=full current
-#define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_K1 0.95      // Smoothing factor within any PID loop
 #if ENABLED(PIDTEMP)
   //#define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
   //#define PID_DEBUG // Sends debug data to the serial port.
@@ -350,7 +351,6 @@
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
-  #define K1 0.95 //smoothing factor within the PID
 
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 

Marlin/src/config/examples/Micromake/C1/enhanced/Configuration.h

@@ -339,8 +339,9 @@
 
 // Comment the following line to disable PID and enable bang-bang.
 #define PIDTEMP
-#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
+#define BANG_MAX 255     // Limits current to nozzle while in bang-bang mode; 255=full current
-#define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_K1 0.95      // Smoothing factor within any PID loop
 #if ENABLED(PIDTEMP)
   //#define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
   //#define PID_DEBUG // Sends debug data to the serial port.
@@ -350,7 +351,6 @@
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
-  #define K1 0.95 //smoothing factor within the PID
 
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 

Marlin/src/config/examples/Mks/Sbase/Configuration.h

@@ -340,8 +340,9 @@
 
 // Comment the following line to disable PID and enable bang-bang.
 #define PIDTEMP
-#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
+#define BANG_MAX 255     // Limits current to nozzle while in bang-bang mode; 255=full current
-#define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_K1 0.95      // Smoothing factor within any PID loop
 #if ENABLED(PIDTEMP)
   //#define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
   //#define PID_DEBUG // Sends debug data to the serial port.
@@ -351,7 +352,6 @@
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
-  #define K1 0.95 //smoothing factor within the PID
 
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 

Marlin/src/config/examples/RepRapWorld/Megatronics/Configuration.h

@@ -339,8 +339,9 @@
 
 // Comment the following line to disable PID and enable bang-bang.
 #define PIDTEMP
-#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
+#define BANG_MAX 255     // Limits current to nozzle while in bang-bang mode; 255=full current
-#define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_K1 0.95      // Smoothing factor within any PID loop
 #if ENABLED(PIDTEMP)
   //#define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
   //#define PID_DEBUG // Sends debug data to the serial port.
@@ -350,7 +351,6 @@
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
-  #define K1 0.95 //smoothing factor within the PID
 
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 

Marlin/src/config/examples/RigidBot/Configuration.h

@@ -342,8 +342,9 @@
 
 // Comment the following line to disable PID and enable bang-bang.
 #define PIDTEMP
-#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
+#define BANG_MAX 255     // Limits current to nozzle while in bang-bang mode; 255=full current
-#define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_K1 0.95      // Smoothing factor within any PID loop
 #if ENABLED(PIDTEMP)
   //#define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
   //#define PID_DEBUG // Sends debug data to the serial port.
@@ -353,7 +354,6 @@
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
-  #define K1 0.95 //smoothing factor within the PID
 
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 

Marlin/src/config/examples/SCARA/Configuration.h

@@ -369,8 +369,9 @@
 
 // Comment the following line to disable PID and enable bang-bang.
 #define PIDTEMP
-#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
+#define BANG_MAX 255     // Limits current to nozzle while in bang-bang mode; 255=full current
-#define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_K1 0.95      // Smoothing factor within any PID loop
 #if ENABLED(PIDTEMP)
   //#define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
   //#define PID_DEBUG // Sends debug data to the serial port.
@@ -380,7 +381,6 @@
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
   #define PID_FUNCTIONAL_RANGE 20 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
-  #define K1 0.95 //smoothing factor within the PID
 
   // Merlin Hotend: From Autotune
   #define  DEFAULT_Kp 24.5

Marlin/src/config/examples/STM32F10/Configuration.h

@@ -340,8 +340,9 @@
 
 // Comment the following line to disable PID and enable bang-bang.
 #define PIDTEMP
-#define BANG_MAX 180 // limits current to nozzle while in bang-bang mode; 255=full current
+#define BANG_MAX 180     // Limits current to nozzle while in bang-bang mode; 255=full current
-#define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_K1 0.95      // Smoothing factor within any PID loop
 #if ENABLED(PIDTEMP)
   #define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
   //#define PID_DEBUG // Sends debug data to the serial port.
@@ -351,7 +352,6 @@
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
-  #define K1 0.95 //smoothing factor within the PID
 
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 

Marlin/src/config/examples/Sanguinololu/Configuration.h

@@ -339,8 +339,9 @@
 
 // Comment the following line to disable PID and enable bang-bang.
 #define PIDTEMP
-#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
+#define BANG_MAX 255     // Limits current to nozzle while in bang-bang mode; 255=full current
-#define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_K1 0.95      // Smoothing factor within any PID loop
 #if ENABLED(PIDTEMP)
   //#define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
   //#define PID_DEBUG // Sends debug data to the serial port.
@@ -350,7 +351,6 @@
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
-  #define K1 0.95 //smoothing factor within the PID
 
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 

Marlin/src/config/examples/TinyBoy2/Configuration.h

@@ -366,8 +366,9 @@
 
 // Comment the following line to disable PID and enable bang-bang.
 #define PIDTEMP
-#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
+#define BANG_MAX 255     // Limits current to nozzle while in bang-bang mode; 255=full current
-#define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_K1 0.95      // Smoothing factor within any PID loop
 #if ENABLED(PIDTEMP)
   //#define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
   //#define PID_DEBUG // Sends debug data to the serial port.
@@ -377,7 +378,6 @@
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
-  #define K1 0.95 //smoothing factor within the PID
 
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 

Marlin/src/config/examples/UltiMachine/Archim2/Configuration.h

@@ -339,8 +339,9 @@
 
 // Comment the following line to disable PID and enable bang-bang.
 #define PIDTEMP
-#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
+#define BANG_MAX 255     // Limits current to nozzle while in bang-bang mode; 255=full current
-#define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_K1 0.95      // Smoothing factor within any PID loop
 #if ENABLED(PIDTEMP)
   //#define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
   //#define PID_DEBUG // Sends debug data to the serial port.
@@ -350,7 +351,6 @@
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
-  #define K1 0.95 //smoothing factor within the PID
 
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 

Marlin/src/config/examples/Velleman/K8200/Configuration.h

@@ -359,8 +359,9 @@
 
 // Comment the following line to disable PID and enable bang-bang.
 #define PIDTEMP
-#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
+#define BANG_MAX 255     // Limits current to nozzle while in bang-bang mode; 255=full current
-#define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_K1 0.95      // Smoothing factor within any PID loop
 #if ENABLED(PIDTEMP)
   //#define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
   //#define PID_DEBUG // Sends debug data to the serial port.
@@ -370,7 +371,6 @@
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
-  #define K1 0.95 //smoothing factor within the PID
 
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 

Marlin/src/config/examples/Velleman/K8400/Configuration.h

@@ -339,8 +339,9 @@
 
 // Comment the following line to disable PID and enable bang-bang.
 #define PIDTEMP
-#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
+#define BANG_MAX 255     // Limits current to nozzle while in bang-bang mode; 255=full current
-#define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_K1 0.95      // Smoothing factor within any PID loop
 #if ENABLED(PIDTEMP)
   //#define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
   //#define PID_DEBUG // Sends debug data to the serial port.
@@ -350,7 +351,6 @@
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
-  #define K1 0.95 //smoothing factor within the PID
 
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 

Marlin/src/config/examples/Velleman/K8400/Dual-head/Configuration.h

@@ -339,8 +339,9 @@
 
 // Comment the following line to disable PID and enable bang-bang.
 #define PIDTEMP
-#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
+#define BANG_MAX 255     // Limits current to nozzle while in bang-bang mode; 255=full current
-#define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_K1 0.95      // Smoothing factor within any PID loop
 #if ENABLED(PIDTEMP)
   //#define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
   //#define PID_DEBUG // Sends debug data to the serial port.
@@ -350,7 +351,6 @@
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
-  #define K1 0.95 //smoothing factor within the PID
 
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 

Marlin/src/config/examples/Wanhao/Duplicator 6/Configuration.h

@@ -342,8 +342,9 @@
 
 // Comment the following line to disable PID and enable bang-bang.
 #define PIDTEMP
-#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
+#define BANG_MAX 255     // Limits current to nozzle while in bang-bang mode; 255=full current
-#define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_K1 0.95      // Smoothing factor within any PID loop
 #if ENABLED(PIDTEMP)
   #define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
   //#define PID_DEBUG // Sends debug data to the serial port.
@@ -353,7 +354,6 @@
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
-  #define K1 0.95 //smoothing factor within the PID
 
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 

Marlin/src/config/examples/adafruit/ST7565/Configuration.h

@@ -339,8 +339,9 @@
 
 // Comment the following line to disable PID and enable bang-bang.
 #define PIDTEMP
-#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
+#define BANG_MAX 255     // Limits current to nozzle while in bang-bang mode; 255=full current
-#define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_K1 0.95      // Smoothing factor within any PID loop
 #if ENABLED(PIDTEMP)
   //#define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
   //#define PID_DEBUG // Sends debug data to the serial port.
@@ -350,7 +351,6 @@
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
-  #define K1 0.95 //smoothing factor within the PID
 
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 

Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration.h

@@ -339,8 +339,9 @@
 
 // Comment the following line to disable PID and enable bang-bang.
 #define PIDTEMP
-#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
+#define BANG_MAX 255     // Limits current to nozzle while in bang-bang mode; 255=full current
-#define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_K1 0.95      // Smoothing factor within any PID loop
 #if ENABLED(PIDTEMP)
   #define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
   //#define PID_DEBUG // Sends debug data to the serial port.
@@ -350,7 +351,6 @@
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
-  #define K1 0.95 //smoothing factor within the PID
 
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 

Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration.h

@@ -339,8 +339,9 @@
 
 // Comment the following line to disable PID and enable bang-bang.
 #define PIDTEMP
-#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
+#define BANG_MAX 255     // Limits current to nozzle while in bang-bang mode; 255=full current
-#define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_K1 0.95      // Smoothing factor within any PID loop
 #if ENABLED(PIDTEMP)
   #define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
   //#define PID_DEBUG // Sends debug data to the serial port.
@@ -350,7 +351,6 @@
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
-  #define K1 0.95 //smoothing factor within the PID
 
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 

Marlin/src/config/examples/delta/generic/Configuration.h

@@ -339,8 +339,9 @@
 
 // Comment the following line to disable PID and enable bang-bang.
 #define PIDTEMP
-#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
+#define BANG_MAX 255     // Limits current to nozzle while in bang-bang mode; 255=full current
-#define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_K1 0.95      // Smoothing factor within any PID loop
 #if ENABLED(PIDTEMP)
   //#define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
   //#define PID_DEBUG // Sends debug data to the serial port.
@@ -350,7 +351,6 @@
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
-  #define K1 0.95 //smoothing factor within the PID
 
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 

Marlin/src/config/examples/delta/kossel_mini/Configuration.h

@@ -339,8 +339,9 @@
 
 // Comment the following line to disable PID and enable bang-bang.
 #define PIDTEMP
-#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
+#define BANG_MAX 255     // Limits current to nozzle while in bang-bang mode; 255=full current
-#define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_K1 0.95      // Smoothing factor within any PID loop
 #if ENABLED(PIDTEMP)
   //#define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
   //#define PID_DEBUG // Sends debug data to the serial port.
@@ -350,7 +351,6 @@
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
-  #define K1 0.95 //smoothing factor within the PID
 
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 

Marlin/src/config/examples/delta/kossel_pro/Configuration.h

@@ -343,8 +343,9 @@
 
 // Comment the following line to disable PID and enable bang-bang.
 #define PIDTEMP
-#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
+#define BANG_MAX 255     // Limits current to nozzle while in bang-bang mode; 255=full current
-#define PID_MAX  125 // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_MAX  125     // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_K1 0.95      // Smoothing factor within any PID loop
 #if ENABLED(PIDTEMP)
   //#define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
   //#define PID_DEBUG // Sends debug data to the serial port.
@@ -354,7 +355,6 @@
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
   #define PID_FUNCTIONAL_RANGE 50 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
-  #define K1 0.95 //smoothing factor within the PID
 
   // Kossel Pro
   #define  DEFAULT_Kp 19.30

Marlin/src/config/examples/delta/kossel_xl/Configuration.h

@@ -339,8 +339,9 @@
 
 // Comment the following line to disable PID and enable bang-bang.
 #define PIDTEMP
-#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
+#define BANG_MAX 255     // Limits current to nozzle while in bang-bang mode; 255=full current
-#define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_K1 0.95      // Smoothing factor within any PID loop
 #if ENABLED(PIDTEMP)
   //#define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
   //#define PID_DEBUG // Sends debug data to the serial port.
@@ -350,7 +351,6 @@
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
-  #define K1 0.95 //smoothing factor within the PID
 
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
   // oXis Kossel k800 XL

Marlin/src/config/examples/gCreate/gMax1.5+/Configuration.h

@@ -347,8 +347,9 @@
 
 // Comment the following line to disable PID and enable bang-bang.
 #define PIDTEMP
-#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
+#define BANG_MAX 255     // Limits current to nozzle while in bang-bang mode; 255=full current
-#define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_K1 0.95      // Smoothing factor within any PID loop
 #if ENABLED(PIDTEMP)
   //#define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
   //#define PID_DEBUG // Sends debug data to the serial port.
@@ -358,7 +359,6 @@
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
-  #define K1 0.95 //smoothing factor within the PID
 
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 

Marlin/src/config/examples/makibox/Configuration.h

@@ -339,8 +339,9 @@
 
 // Comment the following line to disable PID and enable bang-bang.
 #define PIDTEMP
-#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
+#define BANG_MAX 255     // Limits current to nozzle while in bang-bang mode; 255=full current
-#define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_K1 0.95      // Smoothing factor within any PID loop
 #if ENABLED(PIDTEMP)
   //#define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
   //#define PID_DEBUG // Sends debug data to the serial port.
@@ -350,7 +351,6 @@
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
-  #define K1 0.95 //smoothing factor within the PID
 
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 

Marlin/src/config/examples/tvrrug/Round2/Configuration.h

@@ -339,8 +339,9 @@
 
 // Comment the following line to disable PID and enable bang-bang.
 #define PIDTEMP
-#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
+#define BANG_MAX 255     // Limits current to nozzle while in bang-bang mode; 255=full current
-#define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_K1 0.95      // Smoothing factor within any PID loop
 #if ENABLED(PIDTEMP)
   //#define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
   //#define PID_DEBUG // Sends debug data to the serial port.
@@ -350,7 +351,6 @@
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
-  #define K1 0.95 //smoothing factor within the PID
 
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
   // J-Head Mk V-B

Marlin/src/config/examples/wt150/Configuration.h

@@ -339,8 +339,9 @@
 
 // Comment the following line to disable PID and enable bang-bang.
 #define PIDTEMP
-#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
+#define BANG_MAX 255     // Limits current to nozzle while in bang-bang mode; 255=full current
-#define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_K1 0.95      // Smoothing factor within any PID loop
 #if ENABLED(PIDTEMP)
   //#define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
   //#define PID_DEBUG // Sends debug data to the serial port.
@@ -350,7 +351,6 @@
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
-  #define K1 0.95 //smoothing factor within the PID
 
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 

Marlin/src/inc/SanityCheck.h

@@ -225,6 +225,8 @@
   #error "BABYSTEP_ZPROBE_GFX_REVERSE is now set by OVERLAY_GFX_REVERSE. Please update your configurations."
 #elif defined(UBL_GRANULAR_SEGMENTATION_FOR_CARTESIAN)
   #error "UBL_GRANULAR_SEGMENTATION_FOR_CARTESIAN is now SEGMENT_LEVELED_MOVES. Please update your configuration."
+#elif HAS_PID_HEATING && (defined(K1) || !defined(PID_K1))
+  #error "K1 is now PID_K1. Please update your configuration."
 #endif
 
 /**

Marlin/src/module/temperature.cpp

@@ -49,10 +49,6 @@
   #include "../feature/filwidth.h"
 #endif
 
-#ifdef K1 // Defined in Configuration.h in the PID settings
-  #define K2 (1.0-K1)
-#endif
-
 #if ENABLED(TEMP_SENSOR_1_AS_REDUNDANT)
   static void* heater_ttbl_map[2] = { (void*)HEATER_0_TEMPTABLE, (void*)HEATER_1_TEMPTABLE };
   static uint8_t heater_ttbllen_map[2] = { HEATER_0_TEMPTABLE_LEN, HEATER_1_TEMPTABLE_LEN };
@@ -603,7 +599,7 @@ float Temperature::get_pid_output(const int8_t e) {
   #if ENABLED(PIDTEMP)
     #if DISABLED(PID_OPENLOOP)
       pid_error[HOTEND_INDEX] = target_temperature[HOTEND_INDEX] - current_temperature[HOTEND_INDEX];
-      dTerm[HOTEND_INDEX] = K2 * PID_PARAM(Kd, HOTEND_INDEX) * (current_temperature[HOTEND_INDEX] - temp_dState[HOTEND_INDEX]) + K1 * dTerm[HOTEND_INDEX];
+      dTerm[HOTEND_INDEX] = PID_K2 * PID_PARAM(Kd, HOTEND_INDEX) * (current_temperature[HOTEND_INDEX] - temp_dState[HOTEND_INDEX]) + PID_K1 * dTerm[HOTEND_INDEX];
       temp_dState[HOTEND_INDEX] = current_temperature[HOTEND_INDEX];
       #if HEATER_IDLE_HANDLER
         if (heater_idle_timeout_exceeded[HOTEND_INDEX]) {
@@ -700,7 +696,7 @@ float Temperature::get_pid_output(const int8_t e) {
       temp_iState_bed += pid_error_bed;
       iTerm_bed = bedKi * temp_iState_bed;
 
-      dTerm_bed = K2 * bedKd * (current_temperature_bed - temp_dState_bed) + K1 * dTerm_bed;
+      dTerm_bed = PID_K2 * bedKd * (current_temperature_bed - temp_dState_bed) + PID_K1 * dTerm_bed;
       temp_dState_bed = current_temperature_bed;
 
       pid_output = pTerm_bed + iTerm_bed - dTerm_bed;

Marlin/src/module/temperature.h

@@ -88,6 +88,17 @@ enum ADCSensorState {
 
 #define ACTUAL_ADC_SAMPLES max(int(MIN_ADC_ISR_LOOPS), int(SensorsReady))
 
+#if HAS_PID_HEATING
+  #define PID_K2 (1.0-PID_K1)
+  #define PID_dT ((OVERSAMPLENR * float(ACTUAL_ADC_SAMPLES)) / (F_CPU / 64.0 / 256.0))
+
+  // Apply the scale factors to the PID values
+  #define scalePID_i(i)   ( (i) * PID_dT )
+  #define unscalePID_i(i) ( (i) / PID_dT )
+  #define scalePID_d(d)   ( (d) / PID_dT )
+  #define unscalePID_d(d) ( (d) * PID_dT )
+#endif
+
 #if !HAS_HEATER_BED
   constexpr int16_t target_temperature_bed = 0;
 #endif
@@ -116,10 +127,6 @@ class Temperature {
                      soft_pwm_count_fan[FAN_COUNT];
     #endif
 
-    #if ENABLED(PIDTEMP) || ENABLED(PIDTEMPBED)
-      #define PID_dT ((OVERSAMPLENR * float(ACTUAL_ADC_SAMPLES)) / TEMP_TIMER_FREQUENCY)
-    #endif
-
     #if ENABLED(PIDTEMP)
 
       #if ENABLED(PID_PARAMS_PER_HOTEND) && HOTENDS > 1
@@ -140,12 +147,6 @@ class Temperature {
 
       #endif // PID_PARAMS_PER_HOTEND
 
-      // Apply the scale factors to the PID values
-      #define scalePID_i(i)   ( (i) * PID_dT )
-      #define unscalePID_i(i) ( (i) / PID_dT )
-      #define scalePID_d(d)   ( (d) / PID_dT )
-      #define unscalePID_d(d) ( (d) * PID_dT )
-
     #endif
 
     #if ENABLED(PIDTEMPBED)
@@ -431,10 +432,10 @@ class Temperature {
     #if HAS_PID_HEATING
       static void PID_autotune(const float temp, const int8_t hotend, const int8_t ncycles, const bool set_result=false);
 
+      /**
+       * Update the temp manager when PID values change
+       */
       #if ENABLED(PIDTEMP)
-        /**
-         * Update the temp manager when PID values change
-         */
         FORCE_INLINE static void updatePID() {
           #if ENABLED(PID_EXTRUSION_SCALING)
             last_e_position = 0;