Browse Source

Support for Gen3 Monolithic electronics

Techzone Monotronics support, ignoring the tip manager and using fan connector as on Sprinter FW
TODO: Add support for tipmanager
pull/1/head
Alejandro Romero 11 years ago
parent
commit
1c9a70cee9
  1. 1
      Marlin/Configuration.h
  2. 5
      Marlin/Makefile
  3. 65
      Marlin/pins.h

1
Marlin/Configuration.h

@ -63,6 +63,7 @@
// 82 = Brainwave (AT90USB646) // 82 = Brainwave (AT90USB646)
// 83 = SAV Mk-I (AT90USB1286) // 83 = SAV Mk-I (AT90USB1286)
// 9 = Gen3+ // 9 = Gen3+
// 22 = Gen3 Monolithic Electronics
// 70 = Megatronics // 70 = Megatronics
// 701= Megatronics v2.0 // 701= Megatronics v2.0
// 702= Minitronics v1.0 // 702= Minitronics v1.0

5
Marlin/Makefile

@ -157,6 +157,11 @@ else ifeq ($(HARDWARE_MOTHERBOARD),9)
HARDWARE_VARIANT ?= Sanguino HARDWARE_VARIANT ?= Sanguino
MCU ?= atmega644p MCU ?= atmega644p
#Gen3 Monolithic Electronics
else ifeq ($(HARDWARE_MOTHERBOARD),22)
HARDWARE_VARIANT ?= Sanguino
MCU ?= atmega644p
#Megatronics #Megatronics
else ifeq ($(HARDWARE_MOTHERBOARD),70) else ifeq ($(HARDWARE_MOTHERBOARD),70)
HARDWARE_VARIANT ?= arduino HARDWARE_VARIANT ?= arduino

65
Marlin/pins.h

@ -1911,7 +1911,72 @@
#endif #endif
/****************************************************************************************
* Gen3 Monolithic Electronics
*
****************************************************************************************/
#if MOTHERBOARD == 22
#define KNOWN_BOARD 1
#ifndef __AVR_ATmega644P__
#error Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu.
#endif
#define DEBUG_PIN 0
// x axis
#define X_STEP_PIN 15
#define X_DIR_PIN 18
#define X_MIN_PIN 20
//Alex Checar #define X_STOP_PIN 20
#define X_ENABLE_PIN 24 //actually uses Y_enable_pin
#define X_MAX_PIN -1
// y axes
#define Y_STEP_PIN 23
#define Y_DIR_PIN 22
#define Y_MIN_PIN 25
//Alex Checar #define Y_STOP_PIN 25
#define Y_ENABLE_PIN 24 //shared with X_enable_pin
#define Y_MAX_PIN -1
// z axes
#define Z_STEP_PIN 27
#define Z_DIR_PIN 28
#define Z_MIN_PIN 30
//Alex Checar #define Z_STOP_PIN 30
#define Z_ENABLE_PIN 29
#define Z_MAX_PIN -1
//extruder pins
#define E0_STEP_PIN 12
#define E0_DIR_PIN 17
#define E0_ENABLE_PIN 3
#define HEATER_0_PIN 16
#define TEMP_0_PIN 0
#define FAN_PIN -1
//bed pins
#define HEATER_BED_PIN -1
#define TEMP_BED_PIN -1
#define SDSS -1
#define SDPOWER -1
#define LED_PIN -1
//pin for controlling the PSU.
#define PS_ON_PIN 14 //Alex, Do this work on the card?
//Alex extras from Gen3+
#define KILL_PIN -1
#define TEMP_1_PIN -1
#define TEMP_2_PIN -1
#define HEATER_2_PIN -1
#endif
/**************************************************************************************** /****************************************************************************************
* Open Motion controller with enable based extruders * Open Motion controller with enable based extruders

Loading…
Cancel
Save