Update Z probe offset comment

Marlin/Configuration.h

@@ -857,23 +857,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 10  // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 10  // Y offset: -front +behind [the nozzle]

config/default/Configuration.h

@@ -857,23 +857,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 10  // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 10  // Y offset: -front +behind [the nozzle]

config/examples/3DFabXYZ/Migbot/Configuration.h

@@ -863,23 +863,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 21  // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 61  // Y offset: -front +behind [the nozzle]

config/examples/AlephObjects/TAZ4/Configuration.h

@@ -877,23 +877,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER -25     // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER -29     // Y offset: -front +behind [the nozzle]

config/examples/AliExpress/CL-260/Configuration.h

@@ -857,23 +857,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 10  // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 10  // Y offset: -front +behind [the nozzle]

config/examples/AliExpress/UM2pExt/Configuration.h

@@ -868,23 +868,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 10  // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 10  // Y offset: -front +behind [the nozzle]

config/examples/Anet/A2/Configuration.h

@@ -857,23 +857,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 //#define X_PROBE_OFFSET_FROM_EXTRUDER 10  // X offset: -left  +right  [of the nozzle]
 //#define Y_PROBE_OFFSET_FROM_EXTRUDER 10  // Y offset: -front +behind [the nozzle]

config/examples/Anet/A2plus/Configuration.h

@@ -857,23 +857,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 //#define X_PROBE_OFFSET_FROM_EXTRUDER 10  // X offset: -left  +right  [of the nozzle]
 //#define Y_PROBE_OFFSET_FROM_EXTRUDER 10  // Y offset: -front +behind [the nozzle]

config/examples/Anet/A6/Configuration.h

@@ -904,23 +904,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 //#define X_PROBE_OFFSET_FROM_EXTRUDER 10   // X offset: -left  +right  [of the nozzle]
 //#define Y_PROBE_OFFSET_FROM_EXTRUDER 10   // Y offset: -front +behind [the nozzle]

config/examples/Anet/A8/Configuration.h

@@ -870,23 +870,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 0   // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 0   // Y offset: -front +behind [the nozzle]

config/examples/Anet/A8plus/Configuration.h

@@ -868,23 +868,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 10  // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 10  // Y offset: -front +behind [the nozzle]

config/examples/Anet/E16/Configuration.h

@@ -869,23 +869,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 10  // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 10  // Y offset: -front +behind [the nozzle]

config/examples/AnyCubic/i3/Configuration.h

@@ -867,23 +867,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 75  // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 5  // Y offset: -front +behind [the nozzle]

config/examples/ArmEd/Configuration.h

@@ -858,23 +858,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 10  // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 10  // Y offset: -front +behind [the nozzle]

config/examples/Azteeg/X5GT/Configuration.h

@@ -857,23 +857,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 10  // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 10  // Y offset: -front +behind [the nozzle]

config/examples/BIBO/TouchX/cyclops/Configuration.h

@@ -857,23 +857,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 10  // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 10  // Y offset: -front +behind [the nozzle]

config/examples/BIBO/TouchX/default/Configuration.h

@@ -857,23 +857,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 10  // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 10  // Y offset: -front +behind [the nozzle]

config/examples/BQ/Hephestos/Configuration.h

@@ -845,23 +845,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER -25     // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER -29     // Y offset: -front +behind [the nozzle]

config/examples/BQ/Hephestos_2/Configuration.h

@@ -858,23 +858,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 34  // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 15  // Y offset: -front +behind [the nozzle]

config/examples/BQ/WITBOX/Configuration.h

@@ -845,23 +845,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER -25     // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER -29     // Y offset: -front +behind [the nozzle]

config/examples/Cartesio/Configuration.h

@@ -856,23 +856,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 10  // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 10  // Y offset: -front +behind [the nozzle]

config/examples/Creality/CR-10/Configuration.h

@@ -867,23 +867,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 10  // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 10  // Y offset: -front +behind [the nozzle]

config/examples/Creality/CR-10S/Configuration.h

@@ -857,23 +857,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 10  // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 10  // Y offset: -front +behind [the nozzle]

config/examples/Creality/CR-10_5S/Configuration.h

@@ -858,23 +858,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 10  // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 10  // Y offset: -front +behind [the nozzle]

config/examples/Creality/CR-10mini/Configuration.h

@@ -876,23 +876,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 10  // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 10  // Y offset: -front +behind [the nozzle]

config/examples/Creality/CR-8/Configuration.h

@@ -867,23 +867,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 10  // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 10  // Y offset: -front +behind [the nozzle]

config/examples/Creality/Ender-2/Configuration.h

@@ -861,23 +861,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 10  // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 10  // Y offset: -front +behind [the nozzle]

config/examples/Creality/Ender-3/Configuration.h

@@ -861,23 +861,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 10  // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 10  // Y offset: -front +behind [the nozzle]

config/examples/Creality/Ender-4/Configuration.h

@@ -867,23 +867,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 10  // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 10  // Y offset: -front +behind [the nozzle]

config/examples/Einstart-S/Configuration.h

@@ -866,23 +866,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 10  // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 10  // Y offset: -front +behind [the nozzle]

config/examples/Felix/Configuration.h

@@ -839,23 +839,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER -25     // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER -29     // Y offset: -front +behind [the nozzle]

config/examples/Felix/DUAL/Configuration.h

@@ -839,23 +839,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER -25     // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER -29     // Y offset: -front +behind [the nozzle]

config/examples/FlashForge/CreatorPro/Configuration.h

@@ -849,23 +849,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 10  // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 10  // Y offset: -front +behind [the nozzle]

config/examples/FolgerTech/i3-2020/Configuration.h

@@ -863,23 +863,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 38     // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER -7     // Y offset: -front +behind [the nozzle]

config/examples/Formbot/Raptor/Configuration.h

@@ -940,23 +940,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER -22  // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 0  // Y offset: -front +behind [the nozzle]

config/examples/Formbot/T_Rex_2+/Configuration.h

@@ -887,23 +887,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER -3      // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 31      // Y offset: -front +behind [the nozzle]

config/examples/Formbot/T_Rex_3/Configuration.h

@@ -873,23 +873,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER -3      // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 31      // Y offset: -front +behind [the nozzle]

config/examples/Geeetech/A10M/Configuration.h

@@ -841,23 +841,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER -37    // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER   0    // Y offset: -front +behind [the nozzle]

config/examples/Geeetech/A20M/Configuration.h

@@ -841,23 +841,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER -37    // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER   0    // Y offset: -front +behind [the nozzle]

config/examples/Geeetech/GT2560/Configuration.h

@@ -872,23 +872,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 10  // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 10  // Y offset: -front +behind [the nozzle]

config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h

@@ -850,23 +850,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 10  // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 10  // Y offset: -front +behind [the nozzle]

config/examples/Geeetech/MeCreator2/Configuration.h

@@ -864,23 +864,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 10  // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 10  // Y offset: -front +behind [the nozzle]

config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h

@@ -877,23 +877,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 4     // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER -44   // Y offset: -front +behind [the nozzle]

config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h

@@ -877,23 +877,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 10  // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 10  // Y offset: -front +behind [the nozzle]

config/examples/Geeetech/Prusa i3 Pro C/Configuration.h

@@ -857,23 +857,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 10  // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 10  // Y offset: -front +behind [the nozzle]

config/examples/Geeetech/Prusa i3 Pro W/Configuration.h

@@ -857,23 +857,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 10  // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 10  // Y offset: -front +behind [the nozzle]

config/examples/Infitary/i3-M508/Configuration.h

@@ -861,23 +861,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 10  // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 10  // Y offset: -front +behind [the nozzle]

config/examples/JGAurora/A5/Configuration.h

@@ -869,23 +869,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 10  // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 10  // Y offset: -front +behind [the nozzle]

config/examples/MakerParts/Configuration.h

@@ -877,23 +877,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 10  // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 10  // Y offset: -front +behind [the nozzle]

config/examples/Malyan/M150/Configuration.h

@@ -877,23 +877,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 
 // Set for HoolyHoo's probe mount

config/examples/Malyan/M200/Configuration.h

@@ -856,23 +856,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 10  // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 10  // Y offset: -front +behind [the nozzle]

config/examples/Micromake/C1/basic/Configuration.h

@@ -861,23 +861,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 0  // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 0  // Y offset: -front +behind [the nozzle]

config/examples/Micromake/C1/enhanced/Configuration.h

@@ -861,23 +861,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 0  // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 0  // Y offset: -front +behind [the nozzle]

config/examples/Mks/Robin/Configuration.h

@@ -858,23 +858,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 10  // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 10  // Y offset: -front +behind [the nozzle]

config/examples/Mks/Sbase/Configuration.h

@@ -857,23 +857,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 32  // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 5     // Y offset: -front +behind [the nozzle]

config/examples/Printrbot/PrintrboardG2/Configuration.h

@@ -865,23 +865,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 10  // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 10  // Y offset: -front +behind [the nozzle]

config/examples/RapideLite/RL200/Configuration.h

@@ -857,23 +857,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 10  // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 10  // Y offset: -front +behind [the nozzle]

config/examples/RepRapPro/Huxley/Configuration.h

@@ -897,23 +897,23 @@ Black rubber belt(MXL), 18 - tooth aluminium pulley : 87.489 step per mm (Huxley
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 10  // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 10  // Y offset: -front +behind [the nozzle]

config/examples/RepRapWorld/Megatronics/Configuration.h

@@ -857,23 +857,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER -25     // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER -29     // Y offset: -front +behind [the nozzle]

config/examples/RigidBot/Configuration.h

@@ -855,23 +855,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER -25     // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER -29     // Y offset: -front +behind [the nozzle]

config/examples/SCARA/Configuration.h

@@ -870,23 +870,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER -25     // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER -29     // Y offset: -front +behind [the nozzle]

config/examples/STM32/Black_STM32F407VET6/Configuration.h

@@ -857,23 +857,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 10  // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 10  // Y offset: -front +behind [the nozzle]

config/examples/STM32/STM32F10/Configuration.h

@@ -859,23 +859,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER -25  // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER -29  // Y offset: -front +behind [the nozzle]

config/examples/STM32/STM32F4/Configuration.h

@@ -857,23 +857,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 10  // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 10  // Y offset: -front +behind [the nozzle]

config/examples/STM32/stm32f103ret6/Configuration.h

@@ -859,23 +859,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER -25  // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER -29  // Y offset: -front +behind [the nozzle]

config/examples/Sanguinololu/Configuration.h

@@ -888,23 +888,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 10  // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 10  // Y offset: -front +behind [the nozzle]

config/examples/TheBorg/Configuration.h

@@ -857,23 +857,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 32  // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 5     // Y offset: -front +behind [the nozzle]

config/examples/TinyBoy2/Configuration.h

@@ -908,23 +908,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 34  // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 15  // Y offset: -front +behind [the nozzle]

config/examples/Tronxy/X1/Configuration.h

@@ -857,23 +857,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 10  // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 10  // Y offset: -front +behind [the nozzle]

config/examples/Tronxy/X3A/Configuration.h

@@ -857,23 +857,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER -32  // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER -10  // Y offset: -front +behind [the nozzle]

config/examples/Tronxy/X5S-2E/Configuration.h

@@ -878,23 +878,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 10  // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 10  // Y offset: -front +behind [the nozzle]

config/examples/Tronxy/X5S/Configuration.h

@@ -856,23 +856,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER -45  // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER -55  // Y offset: -front +behind [the nozzle]

config/examples/Tronxy/XY100/Configuration.h

@@ -868,23 +868,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 10  // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 10  // Y offset: -front +behind [the nozzle]

config/examples/UltiMachine/Archim1/Configuration.h

@@ -857,23 +857,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 10  // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 10  // Y offset: -front +behind [the nozzle]

config/examples/UltiMachine/Archim2/Configuration.h

@@ -857,23 +857,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 10  // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 10  // Y offset: -front +behind [the nozzle]

config/examples/VORONDesign/Configuration.h

@@ -866,23 +866,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 0   // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 0   // Y offset: -front +behind [the nozzle]

config/examples/Velleman/K8200/Configuration.h

@@ -886,23 +886,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 10  // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 10  // Y offset: -front +behind [the nozzle]

config/examples/Velleman/K8400/Configuration.h

@@ -857,23 +857,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 10  // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 10  // Y offset: -front +behind [the nozzle]

config/examples/Velleman/K8400/Dual-head/Configuration.h

@@ -857,23 +857,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 10  // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 10  // Y offset: -front +behind [the nozzle]

config/examples/WASP/PowerWASP/Configuration.h

@@ -876,23 +876,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 10  // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 10  // Y offset: -front +behind [the nozzle]

config/examples/Wanhao/Duplicator 6/Configuration.h

@@ -867,23 +867,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 10  // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 10  // Y offset: -front +behind [the nozzle]

config/examples/adafruit/ST7565/Configuration.h

@@ -857,23 +857,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER -25     // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER -29     // Y offset: -front +behind [the nozzle]

config/examples/delta/Anycubic/Kossel/Configuration.h

@@ -1036,23 +1036,23 @@
 #endif // Z_PROBE_ALLEN_KEY
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 0     // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 0     // Y offset: -front +behind [the nozzle]

config/examples/delta/FLSUN/auto_calibrate/Configuration.h

@@ -985,23 +985,23 @@
 #endif // Z_PROBE_ALLEN_KEY
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 0     // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 0     // Y offset: -front +behind [the nozzle]

config/examples/delta/FLSUN/kossel/Configuration.h

@@ -984,23 +984,23 @@
 #endif // Z_PROBE_ALLEN_KEY
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 0     // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 0     // Y offset: -front +behind [the nozzle]

config/examples/delta/FLSUN/kossel_mini/Configuration.h

@@ -984,23 +984,23 @@
 #endif // Z_PROBE_ALLEN_KEY
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 0     // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 0   // Y offset: -front +behind [the nozzle]

config/examples/delta/Geeetech/Rostock 301/Configuration.h

@@ -972,23 +972,23 @@
 #endif // Z_PROBE_ALLEN_KEY
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 0     // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER -10   // Y offset: -front +behind [the nozzle]

config/examples/delta/Hatchbox_Alpha/Configuration.h

@@ -987,23 +987,23 @@
 #endif // Z_PROBE_ALLEN_KEY
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 0     // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 0   // Y offset: -front +behind [the nozzle]

config/examples/delta/MKS/SBASE/Configuration.h

@@ -972,23 +972,23 @@
 #endif // Z_PROBE_ALLEN_KEY
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 0     // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER -10   // Y offset: -front +behind [the nozzle]

config/examples/delta/Tevo Little Monster/Configuration.h

@@ -969,23 +969,23 @@
 #endif // Z_PROBE_ALLEN_KEY
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 0     // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 20   // Y offset: -front +behind [the nozzle]

config/examples/delta/generic/Configuration.h

@@ -972,23 +972,23 @@
 #endif // Z_PROBE_ALLEN_KEY
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 0     // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER -10   // Y offset: -front +behind [the nozzle]

config/examples/delta/kossel_mini/Configuration.h

@@ -974,23 +974,23 @@
 #endif // Z_PROBE_ALLEN_KEY
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 0     // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER -10   // Y offset: -front +behind [the nozzle]

config/examples/delta/kossel_pro/Configuration.h

@@ -971,23 +971,23 @@
 #endif // Z_PROBE_ALLEN_KEY
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER -23 // KosselPro actual: -22.919
 #define Y_PROBE_OFFSET_FROM_EXTRUDER -6  // KosselPro actual: -6.304

config/examples/delta/kossel_xl/Configuration.h

@@ -975,23 +975,23 @@
 #endif // Z_PROBE_ALLEN_KEY
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 0.0     // Z probe to nozzle X offset: -left  +right
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 0.0     // Z probe to nozzle Y offset: -front +behind

config/examples/gCreate/gMax1.5+/Configuration.h

@@ -863,23 +863,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER -17    // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER -10    // Y offset: -front +behind [the nozzle]

config/examples/makibox/Configuration.h

@@ -860,23 +860,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER -25     // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER -29     // Y offset: -front +behind [the nozzle]

config/examples/tvrrug/Round2/Configuration.h

@@ -852,23 +852,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER -25     // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER -29     // Y offset: -front +behind [the nozzle]

config/examples/wt150/Configuration.h

@@ -862,23 +862,23 @@
 //
 
 /**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *     +-- BACK ---+
+ *     |           |
+ *   L |    (+) P  | R <-- probe (20,20)
+ *   E |           | I
+ *   F | (-) N (+) | G <-- nozzle (10,10)
+ *   T |           | H
+ *     |    (-)    | T
+ *     |           |
+ *     O-- FRONT --+
+ *   (0,0)
  */
 #define X_PROBE_OFFSET_FROM_EXTRUDER 10  // X offset: -left  +right  [of the nozzle]
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 10  // Y offset: -front +behind [the nozzle]