|
|
|
@ -707,9 +707,9 @@ |
|
|
|
* M204 R Retract Acceleration |
|
|
|
* M204 T Travel Acceleration |
|
|
|
*/ |
|
|
|
#define DEFAULT_ACCELERATION 500 // X, Y, Z and E acceleration for printing moves
|
|
|
|
#define DEFAULT_RETRACT_ACCELERATION 500 // E acceleration for retracts
|
|
|
|
#define DEFAULT_TRAVEL_ACCELERATION 500 // X, Y, Z acceleration for travel (non printing) moves
|
|
|
|
#define DEFAULT_ACCELERATION 1000 // X, Y, Z and E acceleration for printing moves
|
|
|
|
#define DEFAULT_RETRACT_ACCELERATION 2000 // E acceleration for retracts
|
|
|
|
#define DEFAULT_TRAVEL_ACCELERATION 1000 // X, Y, Z acceleration for travel (non printing) moves
|
|
|
|
|
|
|
|
//
|
|
|
|
// Use Junction Deviation instead of traditional Jerk Limiting
|
|
|
|
@ -811,7 +811,8 @@ |
|
|
|
*/ |
|
|
|
//#define BLTOUCH
|
|
|
|
#if ENABLED(BLTOUCH) |
|
|
|
//#define BLTOUCH_DELAY 500 // Minimum Command delay (ms). Enable and increase if needed
|
|
|
|
#define BLTOUCH_DELAY 200 // Minimum Command delay (ms). Enable and increase if needed
|
|
|
|
#define BLTOUCH_HS_MODE |
|
|
|
|
|
|
|
/**
|
|
|
|
* BLTouch V3.0 and newer smart series |
|
|
|
@ -860,7 +861,7 @@ |
|
|
|
*/ |
|
|
|
#define X_PROBE_OFFSET_FROM_EXTRUDER -37 // X offset: -left +right [of the nozzle]
|
|
|
|
#define Y_PROBE_OFFSET_FROM_EXTRUDER 0 // Y offset: -front +behind [the nozzle]
|
|
|
|
#define Z_PROBE_OFFSET_FROM_EXTRUDER -0.5 // Z offset: -below +above [the nozzle]
|
|
|
|
#define Z_PROBE_OFFSET_FROM_EXTRUDER -3.6 // Z offset: -below +above [the nozzle]
|
|
|
|
|
|
|
|
// Certain types of probes need to stay away from edges
|
|
|
|
#define MIN_PROBE_EDGE 10 |
|
|
|
@ -893,16 +894,16 @@ |
|
|
|
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle. |
|
|
|
* But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle. |
|
|
|
*/ |
|
|
|
#define Z_CLEARANCE_DEPLOY_PROBE 10 // Z Clearance for Deploy/Stow
|
|
|
|
#define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points
|
|
|
|
#define Z_CLEARANCE_MULTI_PROBE 5 // Z Clearance between multiple probes
|
|
|
|
//#define Z_AFTER_PROBING 5 // Z position after probing is done
|
|
|
|
#define Z_CLEARANCE_DEPLOY_PROBE 5 // Z Clearance for Deploy/Stow
|
|
|
|
#define Z_CLEARANCE_BETWEEN_PROBES 3 // Z Clearance between probe points
|
|
|
|
#define Z_CLEARANCE_MULTI_PROBE 2 // Z Clearance between multiple probes
|
|
|
|
#define Z_AFTER_PROBING 3 // Z position after probing is done
|
|
|
|
|
|
|
|
#define Z_PROBE_LOW_POINT -2 // Farthest distance below the trigger-point to go before stopping
|
|
|
|
|
|
|
|
// For M851 give a range for adjusting the Z probe offset
|
|
|
|
#define Z_PROBE_OFFSET_RANGE_MIN -20 |
|
|
|
#define Z_PROBE_OFFSET_RANGE_MAX 20 |
|
|
|
#define Z_PROBE_OFFSET_RANGE_MIN -5 |
|
|
|
#define Z_PROBE_OFFSET_RANGE_MAX -0.2 |
|
|
|
|
|
|
|
// Enable the M48 repeatability test to test probe accuracy
|
|
|
|
//#define Z_MIN_PROBE_REPEATABILITY_TEST
|
|
|
|
@ -926,7 +927,7 @@ |
|
|
|
#endif |
|
|
|
#define PROBING_FANS_OFF // Turn fans off when probing
|
|
|
|
//#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing
|
|
|
|
#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
|
|
|
|
#define DELAY_BEFORE_PROBING 100 // (ms) To prevent vibrations from triggering piezo sensors
|
|
|
|
|
|
|
|
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
|
|
|
|
// :{ 0:'Low', 1:'High' }
|
|
|
|
@ -1130,7 +1131,7 @@ |
|
|
|
/**
|
|
|
|
* Enable the G26 Mesh Validation Pattern tool. |
|
|
|
*/ |
|
|
|
//#define G26_MESH_VALIDATION
|
|
|
|
#define G26_MESH_VALIDATION |
|
|
|
#if ENABLED(G26_MESH_VALIDATION) |
|
|
|
#define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
|
|
|
|
#define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool.
|
|
|
|
@ -1144,7 +1145,7 @@ |
|
|
|
#if EITHER(AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_BILINEAR) |
|
|
|
|
|
|
|
// Set the number of grid points per dimension.
|
|
|
|
#define GRID_MAX_POINTS_X 3 |
|
|
|
#define GRID_MAX_POINTS_X 5 |
|
|
|
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X |
|
|
|
|
|
|
|
// Set the boundaries for probing (where the probe can reach).
|
|
|
|
@ -1223,12 +1224,11 @@ |
|
|
|
* Add a bed leveling sub-menu for ABL or MBL. |
|
|
|
* Include a guided procedure if manual probing is enabled. |
|
|
|
*/ |
|
|
|
//#define LCD_BED_LEVELING
|
|
|
|
|
|
|
|
#define LCD_BED_LEVELING |
|
|
|
#if ENABLED(LCD_BED_LEVELING) |
|
|
|
#define MESH_EDIT_Z_STEP 0.025 // (mm) Step size while manually probing Z axis.
|
|
|
|
#define LCD_PROBE_Z_RANGE 4 // (mm) Z Range centered on Z_MIN_POS for LCD Z adjustment
|
|
|
|
//#define MESH_EDIT_MENU // Add a menu to edit mesh points
|
|
|
|
#define MESH_EDIT_MENU // Add a menu to edit mesh points
|
|
|
|
#endif |
|
|
|
|
|
|
|
// Add a menu item to move between bed corners for manual bed adjustment
|
|
|
|
@ -1276,7 +1276,7 @@ |
|
|
|
#endif |
|
|
|
|
|
|
|
// Homing speeds (mm/m)
|
|
|
|
#define HOMING_FEEDRATE_XY (100*60) |
|
|
|
#define HOMING_FEEDRATE_XY (80*60) |
|
|
|
#define HOMING_FEEDRATE_Z (20*60) |
|
|
|
|
|
|
|
// Validate that endstops are triggered on homing moves
|
|
|
|
@ -1414,7 +1414,7 @@ |
|
|
|
|
|
|
|
#if ENABLED(NOZZLE_PARK_FEATURE) |
|
|
|
// Specify a park position as { X, Y, Z_raise }
|
|
|
|
#define NOZZLE_PARK_POINT { 3, 3, 10 } |
|
|
|
#define NOZZLE_PARK_POINT { 3, (Y_MAX_POS - 3), 10 } |
|
|
|
#define NOZZLE_PARK_XY_FEEDRATE 100 // (mm/s) X and Y axes feedrate (also used for delta Z axis)
|
|
|
|
#define NOZZLE_PARK_Z_FEEDRATE 5 // (mm/s) Z axis feedrate (not used for delta printers)
|
|
|
|
#endif |
|
|
|
|
Scott Lahteine
5 years ago