Bob Kuhn
5 years ago
committed by
Scott Lahteine
Scott Lahteine
6 changed files with 144 additions and 22 deletions
@ -0,0 +1,99 @@ |
|||
/**
|
|||
* Marlin 3D Printer Firmware |
|||
* Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
|||
* |
|||
* Based on Sprinter and grbl. |
|||
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm |
|||
* |
|||
* This program is free software: you can redistribute it and/or modify |
|||
* it under the terms of the GNU General Public License as published by |
|||
* the Free Software Foundation, either version 3 of the License, or |
|||
* (at your option) any later version. |
|||
* |
|||
* This program is distributed in the hope that it will be useful, |
|||
* but WITHOUT ANY WARRANTY; without even the implied warranty of |
|||
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
|||
* GNU General Public License for more details. |
|||
* |
|||
* You should have received a copy of the GNU General Public License |
|||
* along with this program. If not, see <http://www.gnu.org/licenses/>.
|
|||
* |
|||
*/ |
|||
|
|||
#include "../../inc/MarlinConfig.h" |
|||
|
|||
#if ENABLED(SMART_EFFECTOR) && PIN_EXISTS(SMART_EFFECTOR_MOD) |
|||
|
|||
#include "../gcode.h" |
|||
#include "../../HAL/shared/Delay.h" |
|||
#include "../parser.h" |
|||
|
|||
/**
|
|||
* M672 - Set/reset Duet Smart Effector sensitivity |
|||
* |
|||
* One of these is required: |
|||
* S<sensitivity> - 0-255 |
|||
* R - Flag to reset sensitivity to default |
|||
*/ |
|||
|
|||
/**
|
|||
* The Marlin format for the M672 command is different than shown in the Duet Smart Effector |
|||
* documentation https://duet3d.dozuki.com/Wiki/Smart_effector_and_carriage_adapters_for_delta_printer
|
|||
* |
|||
* To set custom sensitivity: |
|||
* Duet: M672 S105:aaa:bbb |
|||
* Marlin: M672 Saaa |
|||
* |
|||
* (where aaa is the desired sensitivity and bbb is 255 - aaa). |
|||
* |
|||
* Revert sensitivity to factory settings: |
|||
* Duet: M672 S105:131:131 |
|||
* Marlin: M672 R |
|||
*/ |
|||
|
|||
#define M672_PROGBYTE 105 // magic byte to start programming custom sensitivity
|
|||
#define M672_ERASEBYTE 131 // magic byte to clear custom sensitivity
|
|||
|
|||
//
|
|||
// Smart Effector byte send protocol:
|
|||
//
|
|||
// 0 0 1 0 ... always 0010
|
|||
// b7 b6 b5 b4 ~b4 ... hi bits, NOT last bit
|
|||
// b3 b2 b1 b0 ~b0 ... lo bits, NOT last bit
|
|||
//
|
|||
void M672_send(uint8_t b) { // bit rate requirement: 1KHz +/- 30%
|
|||
for (uint8_t bits = 0; bits < 14; bits++) { |
|||
switch (bits) { |
|||
default: { OUT_WRITE(SMART_EFFECTOR_MOD_PIN, !!(b & 0x80)); b <<= 1; break; } // send bit, shift next into place
|
|||
case 7: |
|||
case 12: { OUT_WRITE(SMART_EFFECTOR_MOD_PIN, !!(b & 0x80)); break; } // send bit. no shift
|
|||
case 8: |
|||
case 13: { OUT_WRITE(SMART_EFFECTOR_MOD_PIN, !(b & 0x80)); b <<= 1; break; } // send inverted previous bit
|
|||
case 0: case 1: // 00
|
|||
case 3: { OUT_WRITE(SMART_EFFECTOR_MOD_PIN, LOW); break; } // 0010
|
|||
case 2: { OUT_WRITE(SMART_EFFECTOR_MOD_PIN, HIGH); break; } // 001
|
|||
} |
|||
DELAY_US(1000); |
|||
} |
|||
} |
|||
|
|||
void GcodeSuite::M672() { |
|||
if (parser.seen('R')) { |
|||
M672_send(M672_ERASEBYTE); |
|||
M672_send(M672_ERASEBYTE); |
|||
} |
|||
else if (parser.seenval('S')) { |
|||
const int8_t M672_sensitivity = parser.value_byte(); |
|||
M672_send(M672_PROGBYTE); |
|||
M672_send(M672_sensitivity); |
|||
M672_send(255 - M672_sensitivity); |
|||
} |
|||
else { |
|||
SERIAL_ECHO_MSG("!'S' or 'R' parameter required."); |
|||
return; |
|||
} |
|||
|
|||
OUT_WRITE(SMART_EFFECTOR_MOD_PIN, LOW); // Keep Smart Effector in NORMAL mode
|
|||
} |
|||
|
|||
#endif // SMART_EFFECTOR && SMART_EFFECTOR_MOD_PIN
|
|||
Loading…
Reference in new issue