diff --git a/Marlin/example_configurations/Felix/Configuration.h b/Marlin/example_configurations/Felix/Configuration.h index c06bfa0517..f946d35c0a 100644 --- a/Marlin/example_configurations/Felix/Configuration.h +++ b/Marlin/example_configurations/Felix/Configuration.h @@ -460,14 +460,14 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l #else // !AUTO_BED_LEVELING_GRID - // Arbitrary points to probe. - // A simple cross-product is used to estimate the plane of the bed. - #define ABL_PROBE_PT_1_X 15 - #define ABL_PROBE_PT_1_Y 180 - #define ABL_PROBE_PT_2_X 15 - #define ABL_PROBE_PT_2_Y 20 - #define ABL_PROBE_PT_3_X 170 - #define ABL_PROBE_PT_3_Y 20 + // Arbitrary points to probe. + // A simple cross-product is used to estimate the plane of the bed. + #define ABL_PROBE_PT_1_X 15 + #define ABL_PROBE_PT_1_Y 180 + #define ABL_PROBE_PT_2_X 15 + #define ABL_PROBE_PT_2_Y 20 + #define ABL_PROBE_PT_3_X 170 + #define ABL_PROBE_PT_3_Y 20 #endif // AUTO_BED_LEVELING_GRID @@ -486,14 +486,14 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l #define Z_RAISE_BETWEEN_PROBINGS 5 // How much the Z axis will be raised when traveling from between next probing points. #define Z_RAISE_AFTER_PROBING 15 // How much the Z axis will be raised after the last probing point. -//#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine. - // Useful to retract a deployable Z probe. + //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine. + // Useful to retract a deployable Z probe. //#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. -// If you have enabled the bed auto leveling and are using the same Z probe for Z homing, -// it is highly recommended you let this Z_SAFE_HOMING enabled!!! + // If you have enabled the bed auto leveling and are using the same Z probe for Z homing, + // it is highly recommended you let this Z_SAFE_HOMING enabled!!! #define Z_SAFE_HOMING // This feature is meant to avoid Z homing with Z probe outside the bed area. // When defined, it will: diff --git a/Marlin/example_configurations/Felix/Configuration_DUAL.h b/Marlin/example_configurations/Felix/Configuration_DUAL.h index a0368c40e9..bd7b8eed4e 100644 --- a/Marlin/example_configurations/Felix/Configuration_DUAL.h +++ b/Marlin/example_configurations/Felix/Configuration_DUAL.h @@ -228,10 +228,10 @@ Here are some standard links for getting your machine calibrated: //#define PID_BED_DEBUG // Sends debug data to the serial port. #if ENABLED(PIDTEMPBED) -// Felix Foil Heater - #define DEFAULT_bedKp 103.37 - #define DEFAULT_bedKi 2.79 - #define DEFAULT_bedKd 956.94 + // Felix Foil Heater + #define DEFAULT_bedKp 103.37 + #define DEFAULT_bedKi 2.79 + #define DEFAULT_bedKd 956.94 // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. #endif // PIDTEMPBED @@ -431,14 +431,14 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l #else // !AUTO_BED_LEVELING_GRID - // Arbitrary points to probe. - // A simple cross-product is used to estimate the plane of the bed. - #define ABL_PROBE_PT_1_X 15 - #define ABL_PROBE_PT_1_Y 180 - #define ABL_PROBE_PT_2_X 15 - #define ABL_PROBE_PT_2_Y 20 - #define ABL_PROBE_PT_3_X 170 - #define ABL_PROBE_PT_3_Y 20 + // Arbitrary points to probe. + // A simple cross-product is used to estimate the plane of the bed. + #define ABL_PROBE_PT_1_X 15 + #define ABL_PROBE_PT_1_Y 180 + #define ABL_PROBE_PT_2_X 15 + #define ABL_PROBE_PT_2_Y 20 + #define ABL_PROBE_PT_3_X 170 + #define ABL_PROBE_PT_3_Y 20 #endif // AUTO_BED_LEVELING_GRID @@ -457,14 +457,14 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l #define Z_RAISE_BETWEEN_PROBINGS 5 // How much the Z axis will be raised when traveling from between next probing points. #define Z_RAISE_AFTER_PROBING 15 // How much the Z axis will be raised after the last probing point. -//#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine. - // Useful to retract a deployable Z probe. + //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine. + // Useful to retract a deployable Z probe. //#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. -// If you have enabled the bed auto leveling and are using the same Z probe for Z homing, -// it is highly recommended you let this Z_SAFE_HOMING enabled!!! + // If you have enabled the bed auto leveling and are using the same Z probe for Z homing, + // it is highly recommended you let this Z_SAFE_HOMING enabled!!! #define Z_SAFE_HOMING // This feature is meant to avoid Z homing with Z probe outside the bed area. // When defined, it will: diff --git a/Marlin/example_configurations/Hephestos/Configuration.h b/Marlin/example_configurations/Hephestos/Configuration.h index cd71535488..9fe3715f7f 100644 --- a/Marlin/example_configurations/Hephestos/Configuration.h +++ b/Marlin/example_configurations/Hephestos/Configuration.h @@ -471,14 +471,14 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo #else // !AUTO_BED_LEVELING_GRID - // Arbitrary points to probe. - // A simple cross-product is used to estimate the plane of the bed. - #define ABL_PROBE_PT_1_X 15 - #define ABL_PROBE_PT_1_Y 180 - #define ABL_PROBE_PT_2_X 15 - #define ABL_PROBE_PT_2_Y 20 - #define ABL_PROBE_PT_3_X 170 - #define ABL_PROBE_PT_3_Y 20 + // Arbitrary points to probe. + // A simple cross-product is used to estimate the plane of the bed. + #define ABL_PROBE_PT_1_X 15 + #define ABL_PROBE_PT_1_Y 180 + #define ABL_PROBE_PT_2_X 15 + #define ABL_PROBE_PT_2_Y 20 + #define ABL_PROBE_PT_3_X 170 + #define ABL_PROBE_PT_3_Y 20 #endif // AUTO_BED_LEVELING_GRID @@ -497,14 +497,14 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo #define Z_RAISE_BETWEEN_PROBINGS 5 // How much the Z axis will be raised when traveling from between next probing points. #define Z_RAISE_AFTER_PROBING 15 // How much the Z axis will be raised after the last probing point. -//#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine. - // Useful to retract a deployable Z probe. + //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine. + // Useful to retract a deployable Z probe. //#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. -// If you have enabled the bed auto leveling and are using the same Z probe for Z homing, -// it is highly recommended you let this Z_SAFE_HOMING enabled!!! + // If you have enabled the bed auto leveling and are using the same Z probe for Z homing, + // it is highly recommended you let this Z_SAFE_HOMING enabled!!! #define Z_SAFE_HOMING // This feature is meant to avoid Z homing with Z probe outside the bed area. // When defined, it will: diff --git a/Marlin/example_configurations/K8200/Configuration.h b/Marlin/example_configurations/K8200/Configuration.h index 3287924dc5..426d8e9b68 100644 --- a/Marlin/example_configurations/K8200/Configuration.h +++ b/Marlin/example_configurations/K8200/Configuration.h @@ -466,14 +466,14 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l #else // !AUTO_BED_LEVELING_GRID - // Arbitrary points to probe. - // A simple cross-product is used to estimate the plane of the bed. - #define ABL_PROBE_PT_1_X 15 - #define ABL_PROBE_PT_1_Y 180 - #define ABL_PROBE_PT_2_X 15 - #define ABL_PROBE_PT_2_Y 20 - #define ABL_PROBE_PT_3_X 170 - #define ABL_PROBE_PT_3_Y 20 + // Arbitrary points to probe. + // A simple cross-product is used to estimate the plane of the bed. + #define ABL_PROBE_PT_1_X 15 + #define ABL_PROBE_PT_1_Y 180 + #define ABL_PROBE_PT_2_X 15 + #define ABL_PROBE_PT_2_Y 20 + #define ABL_PROBE_PT_3_X 170 + #define ABL_PROBE_PT_3_Y 20 #endif // AUTO_BED_LEVELING_GRID @@ -492,14 +492,14 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l #define Z_RAISE_BETWEEN_PROBINGS 5 // How much the Z axis will be raised when traveling from between next probing points. #define Z_RAISE_AFTER_PROBING 15 // How much the Z axis will be raised after the last probing point. -//#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine. - // Useful to retract a deployable Z probe. + //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine. + // Useful to retract a deployable Z probe. //#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. -// If you have enabled the bed auto leveling and are using the same Z probe for Z homing, -// it is highly recommended you let this Z_SAFE_HOMING enabled!!! + // If you have enabled the bed auto leveling and are using the same Z probe for Z homing, + // it is highly recommended you let this Z_SAFE_HOMING enabled!!! #define Z_SAFE_HOMING // This feature is meant to avoid Z homing with Z probe outside the bed area. // When defined, it will: diff --git a/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h b/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h index 115baee3cd..e03debc8fc 100644 --- a/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h +++ b/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h @@ -479,14 +479,14 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l #else // !AUTO_BED_LEVELING_GRID - // Arbitrary points to probe. - // A simple cross-product is used to estimate the plane of the bed. - #define ABL_PROBE_PT_1_X 15 - #define ABL_PROBE_PT_1_Y 180 - #define ABL_PROBE_PT_2_X 15 - #define ABL_PROBE_PT_2_Y 20 - #define ABL_PROBE_PT_3_X 170 - #define ABL_PROBE_PT_3_Y 20 + // Arbitrary points to probe. + // A simple cross-product is used to estimate the plane of the bed. + #define ABL_PROBE_PT_1_X 15 + #define ABL_PROBE_PT_1_Y 180 + #define ABL_PROBE_PT_2_X 15 + #define ABL_PROBE_PT_2_Y 20 + #define ABL_PROBE_PT_3_X 170 + #define ABL_PROBE_PT_3_Y 20 #endif // AUTO_BED_LEVELING_GRID @@ -505,14 +505,14 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l #define Z_RAISE_BETWEEN_PROBINGS 5 // How much the Z axis will be raised when traveling from between next probing points. #define Z_RAISE_AFTER_PROBING 15 // How much the Z axis will be raised after the last probing point. -//#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine. - // Useful to retract a deployable Z probe. + //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine. + // Useful to retract a deployable Z probe. //#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. -// If you have enabled the bed auto leveling and are using the same Z probe for Z homing, -// it is highly recommended you let this Z_SAFE_HOMING enabled!!! + // If you have enabled the bed auto leveling and are using the same Z probe for Z homing, + // it is highly recommended you let this Z_SAFE_HOMING enabled!!! #define Z_SAFE_HOMING // This feature is meant to avoid Z homing with Z probe outside the bed area. // When defined, it will: diff --git a/Marlin/example_configurations/RigidBot/Configuration.h b/Marlin/example_configurations/RigidBot/Configuration.h index 154a5da778..987fc36d33 100644 --- a/Marlin/example_configurations/RigidBot/Configuration.h +++ b/Marlin/example_configurations/RigidBot/Configuration.h @@ -464,14 +464,14 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l #else // !AUTO_BED_LEVELING_GRID - // Arbitrary points to probe. - // A simple cross-product is used to estimate the plane of the bed. - #define ABL_PROBE_PT_1_X 15 - #define ABL_PROBE_PT_1_Y 180 - #define ABL_PROBE_PT_2_X 15 - #define ABL_PROBE_PT_2_Y 20 - #define ABL_PROBE_PT_3_X 170 - #define ABL_PROBE_PT_3_Y 20 + // Arbitrary points to probe. + // A simple cross-product is used to estimate the plane of the bed. + #define ABL_PROBE_PT_1_X 15 + #define ABL_PROBE_PT_1_Y 180 + #define ABL_PROBE_PT_2_X 15 + #define ABL_PROBE_PT_2_Y 20 + #define ABL_PROBE_PT_3_X 170 + #define ABL_PROBE_PT_3_Y 20 #endif // AUTO_BED_LEVELING_GRID @@ -490,14 +490,14 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l #define Z_RAISE_BETWEEN_PROBINGS 5 // How much the Z axis will be raised when traveling from between next probing points. #define Z_RAISE_AFTER_PROBING 15 // How much the Z axis will be raised after the last probing point. -//#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine. - // Useful to retract a deployable Z probe. + //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine. + // Useful to retract a deployable Z probe. //#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. -// If you have enabled the bed auto leveling and are using the same Z probe for Z homing, -// it is highly recommended you let this Z_SAFE_HOMING enabled!!! + // If you have enabled the bed auto leveling and are using the same Z probe for Z homing, + // it is highly recommended you let this Z_SAFE_HOMING enabled!!! #define Z_SAFE_HOMING // This feature is meant to avoid Z homing with Z probe outside the bed area. // When defined, it will: diff --git a/Marlin/example_configurations/SCARA/Configuration.h b/Marlin/example_configurations/SCARA/Configuration.h index da24a5b214..05c315917f 100644 --- a/Marlin/example_configurations/SCARA/Configuration.h +++ b/Marlin/example_configurations/SCARA/Configuration.h @@ -331,9 +331,9 @@ Here are some standard links for getting your machine calibrated: // fine endstop settings: Individual pullups. will be ignored if ENDSTOPPULLUPS is defined //#define ENDSTOPPULLUP_XMAX //#define ENDSTOPPULLUP_YMAX - #define ENDSTOPPULLUP_ZMAX // open pin, inverted - #define ENDSTOPPULLUP_XMIN // open pin, inverted - #define ENDSTOPPULLUP_YMIN // open pin, inverted + #define ENDSTOPPULLUP_ZMAX // open pin, inverted + #define ENDSTOPPULLUP_XMIN // open pin, inverted + #define ENDSTOPPULLUP_YMIN // open pin, inverted //#define ENDSTOPPULLUP_ZMIN //#define ENDSTOPPULLUP_ZMIN_PROBE #endif @@ -486,14 +486,14 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l #else // !AUTO_BED_LEVELING_GRID - // Arbitrary points to probe. - // A simple cross-product is used to estimate the plane of the bed. - #define ABL_PROBE_PT_1_X 15 - #define ABL_PROBE_PT_1_Y 180 - #define ABL_PROBE_PT_2_X 15 - #define ABL_PROBE_PT_2_Y 20 - #define ABL_PROBE_PT_3_X 170 - #define ABL_PROBE_PT_3_Y 20 + // Arbitrary points to probe. + // A simple cross-product is used to estimate the plane of the bed. + #define ABL_PROBE_PT_1_X 15 + #define ABL_PROBE_PT_1_Y 180 + #define ABL_PROBE_PT_2_X 15 + #define ABL_PROBE_PT_2_Y 20 + #define ABL_PROBE_PT_3_X 170 + #define ABL_PROBE_PT_3_Y 20 #endif // AUTO_BED_LEVELING_GRID @@ -512,21 +512,21 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l #define Z_RAISE_BETWEEN_PROBINGS 5 // How much the Z axis will be raised when traveling from between next probing points. #define Z_RAISE_AFTER_PROBING 15 // How much the Z axis will be raised after the last probing point. -//#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine. - // Useful to retract a deployable Z probe. + //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine. + // Useful to retract a deployable Z probe. //#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. -// If you have enabled the bed auto leveling and are using the same Z probe for Z homing, -// it is highly recommended you let this Z_SAFE_HOMING enabled!!! + // If you have enabled the bed auto leveling and are using the same Z probe for Z homing, + // it is highly recommended you let this Z_SAFE_HOMING enabled!!! - //#define Z_SAFE_HOMING // This feature is meant to avoid Z homing with Z probe outside the bed area. - // When defined, it will: - // - Allow Z homing only after X and Y homing AND stepper drivers still enabled. - // - If stepper drivers timeout, it will need X and Y homing again before Z homing. - // - Position the Z probe in a defined XY point before Z Homing when homing all axis (G28). - // - Block Z homing only when the Z probe is outside bed area. + //#define Z_SAFE_HOMING // This feature is meant to avoid Z homing with Z probe outside the bed area. + // When defined, it will: + // - Allow Z homing only after X and Y homing AND stepper drivers still enabled. + // - If stepper drivers timeout, it will need X and Y homing again before Z homing. + // - Position the Z probe in a defined XY point before Z Homing when homing all axis (G28). + // - Block Z homing only when the Z probe is outside bed area. #if ENABLED(Z_SAFE_HOMING) diff --git a/Marlin/example_configurations/TAZ4/Configuration.h b/Marlin/example_configurations/TAZ4/Configuration.h index d7f312a4fc..484d32da14 100644 --- a/Marlin/example_configurations/TAZ4/Configuration.h +++ b/Marlin/example_configurations/TAZ4/Configuration.h @@ -497,14 +497,14 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l #else // !AUTO_BED_LEVELING_GRID - // Arbitrary points to probe. - // A simple cross-product is used to estimate the plane of the bed. - #define ABL_PROBE_PT_1_X 15 - #define ABL_PROBE_PT_1_Y 180 - #define ABL_PROBE_PT_2_X 15 - #define ABL_PROBE_PT_2_Y 20 - #define ABL_PROBE_PT_3_X 170 - #define ABL_PROBE_PT_3_Y 20 + // Arbitrary points to probe. + // A simple cross-product is used to estimate the plane of the bed. + #define ABL_PROBE_PT_1_X 15 + #define ABL_PROBE_PT_1_Y 180 + #define ABL_PROBE_PT_2_X 15 + #define ABL_PROBE_PT_2_Y 20 + #define ABL_PROBE_PT_3_X 170 + #define ABL_PROBE_PT_3_Y 20 #endif // AUTO_BED_LEVELING_GRID @@ -523,14 +523,14 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l #define Z_RAISE_BETWEEN_PROBINGS 5 // How much the Z axis will be raised when traveling from between next probing points. #define Z_RAISE_AFTER_PROBING 15 // How much the Z axis will be raised after the last probing point. -//#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine. - // Useful to retract a deployable Z probe. + //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine. + // Useful to retract a deployable Z probe. //#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. -// If you have enabled the bed auto leveling and are using the same Z probe for Z homing, -// it is highly recommended you let this Z_SAFE_HOMING enabled!!! + // If you have enabled the bed auto leveling and are using the same Z probe for Z homing, + // it is highly recommended you let this Z_SAFE_HOMING enabled!!! #define Z_SAFE_HOMING // This feature is meant to avoid Z homing with Z probe outside the bed area. // When defined, it will: diff --git a/Marlin/example_configurations/WITBOX/Configuration.h b/Marlin/example_configurations/WITBOX/Configuration.h index 19fc03403f..2d235e59e7 100644 --- a/Marlin/example_configurations/WITBOX/Configuration.h +++ b/Marlin/example_configurations/WITBOX/Configuration.h @@ -470,14 +470,14 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo #else // !AUTO_BED_LEVELING_GRID - // Arbitrary points to probe. - // A simple cross-product is used to estimate the plane of the bed. - #define ABL_PROBE_PT_1_X 15 - #define ABL_PROBE_PT_1_Y 180 - #define ABL_PROBE_PT_2_X 15 - #define ABL_PROBE_PT_2_Y 20 - #define ABL_PROBE_PT_3_X 170 - #define ABL_PROBE_PT_3_Y 20 + // Arbitrary points to probe. + // A simple cross-product is used to estimate the plane of the bed. + #define ABL_PROBE_PT_1_X 15 + #define ABL_PROBE_PT_1_Y 180 + #define ABL_PROBE_PT_2_X 15 + #define ABL_PROBE_PT_2_Y 20 + #define ABL_PROBE_PT_3_X 170 + #define ABL_PROBE_PT_3_Y 20 #endif // AUTO_BED_LEVELING_GRID @@ -496,14 +496,14 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo #define Z_RAISE_BETWEEN_PROBINGS 5 // How much the Z axis will be raised when traveling from between next probing points. #define Z_RAISE_AFTER_PROBING 15 // How much the Z axis will be raised after the last probing point. -//#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine. - // Useful to retract a deployable Z probe. + //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine. + // Useful to retract a deployable Z probe. //#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. -// If you have enabled the bed auto leveling and are using the same Z probe for Z homing, -// it is highly recommended you let this Z_SAFE_HOMING enabled!!! + // If you have enabled the bed auto leveling and are using the same Z probe for Z homing, + // it is highly recommended you let this Z_SAFE_HOMING enabled!!! #define Z_SAFE_HOMING // This feature is meant to avoid Z homing with Z probe outside the bed area. // When defined, it will: diff --git a/Marlin/example_configurations/adafruit/ST7565/Configuration.h b/Marlin/example_configurations/adafruit/ST7565/Configuration.h index 90935308de..442ee1d7b4 100644 --- a/Marlin/example_configurations/adafruit/ST7565/Configuration.h +++ b/Marlin/example_configurations/adafruit/ST7565/Configuration.h @@ -479,14 +479,14 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l #else // !AUTO_BED_LEVELING_GRID - // Arbitrary points to probe. - // A simple cross-product is used to estimate the plane of the bed. - #define ABL_PROBE_PT_1_X 15 - #define ABL_PROBE_PT_1_Y 180 - #define ABL_PROBE_PT_2_X 15 - #define ABL_PROBE_PT_2_Y 20 - #define ABL_PROBE_PT_3_X 170 - #define ABL_PROBE_PT_3_Y 20 + // Arbitrary points to probe. + // A simple cross-product is used to estimate the plane of the bed. + #define ABL_PROBE_PT_1_X 15 + #define ABL_PROBE_PT_1_Y 180 + #define ABL_PROBE_PT_2_X 15 + #define ABL_PROBE_PT_2_Y 20 + #define ABL_PROBE_PT_3_X 170 + #define ABL_PROBE_PT_3_Y 20 #endif // AUTO_BED_LEVELING_GRID @@ -505,14 +505,14 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l #define Z_RAISE_BETWEEN_PROBINGS 5 // How much the Z axis will be raised when traveling from between next probing points. #define Z_RAISE_AFTER_PROBING 15 // How much the Z axis will be raised after the last probing point. -//#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine. - // Useful to retract a deployable Z probe. + //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine. + // Useful to retract a deployable Z probe. //#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. -// If you have enabled the bed auto leveling and are using the same Z probe for Z homing, -// it is highly recommended you let this Z_SAFE_HOMING enabled!!! + // If you have enabled the bed auto leveling and are using the same Z probe for Z homing, + // it is highly recommended you let this Z_SAFE_HOMING enabled!!! #define Z_SAFE_HOMING // This feature is meant to avoid Z homing with Z probe outside the bed area. // When defined, it will: diff --git a/Marlin/example_configurations/delta/biv2.5/Configuration.h b/Marlin/example_configurations/delta/biv2.5/Configuration.h index bbb15ffa8f..ec78143c63 100644 --- a/Marlin/example_configurations/delta/biv2.5/Configuration.h +++ b/Marlin/example_configurations/delta/biv2.5/Configuration.h @@ -517,14 +517,14 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo #else // !AUTO_BED_LEVELING_GRID - // Arbitrary points to probe. - // A simple cross-product is used to estimate the plane of the bed. - #define ABL_PROBE_PT_1_X 15 - #define ABL_PROBE_PT_1_Y 180 - #define ABL_PROBE_PT_2_X 15 - #define ABL_PROBE_PT_2_Y 20 - #define ABL_PROBE_PT_3_X 170 - #define ABL_PROBE_PT_3_Y 20 + // Arbitrary points to probe. + // A simple cross-product is used to estimate the plane of the bed. + #define ABL_PROBE_PT_1_X 15 + #define ABL_PROBE_PT_1_Y 180 + #define ABL_PROBE_PT_2_X 15 + #define ABL_PROBE_PT_2_Y 20 + #define ABL_PROBE_PT_3_X 170 + #define ABL_PROBE_PT_3_Y 20 #endif // AUTO_BED_LEVELING_GRID @@ -543,8 +543,8 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo #define Z_RAISE_BETWEEN_PROBINGS 5 // How much the Z axis will be raised when traveling from between next probing points. #define Z_RAISE_AFTER_PROBING 50 // How much the Z axis will be raised after the last probing point. -//#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine. - // Useful to retract a deployable Z probe. + //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine. + // Useful to retract a deployable Z probe. //#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. @@ -630,8 +630,8 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE HOMING_FEEDRATE_XYZ #endif -// If you have enabled the bed auto leveling and are using the same Z probe for Z homing, -// it is highly recommended you let this Z_SAFE_HOMING enabled!!! + // If you have enabled the bed auto leveling and are using the same Z probe for Z homing, + // it is highly recommended you let this Z_SAFE_HOMING enabled!!! #define Z_SAFE_HOMING // This feature is meant to avoid Z homing with Z probe outside the bed area. // When defined, it will: diff --git a/Marlin/example_configurations/delta/generic/Configuration.h b/Marlin/example_configurations/delta/generic/Configuration.h index 7b8afbef08..78284a928d 100644 --- a/Marlin/example_configurations/delta/generic/Configuration.h +++ b/Marlin/example_configurations/delta/generic/Configuration.h @@ -518,14 +518,14 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo #else // !AUTO_BED_LEVELING_GRID - // Arbitrary points to probe. - // A simple cross-product is used to estimate the plane of the bed. - #define ABL_PROBE_PT_1_X 15 - #define ABL_PROBE_PT_1_Y 180 - #define ABL_PROBE_PT_2_X 15 - #define ABL_PROBE_PT_2_Y 20 - #define ABL_PROBE_PT_3_X 170 - #define ABL_PROBE_PT_3_Y 20 + // Arbitrary points to probe. + // A simple cross-product is used to estimate the plane of the bed. + #define ABL_PROBE_PT_1_X 15 + #define ABL_PROBE_PT_1_Y 180 + #define ABL_PROBE_PT_2_X 15 + #define ABL_PROBE_PT_2_Y 20 + #define ABL_PROBE_PT_3_X 170 + #define ABL_PROBE_PT_3_Y 20 #endif // AUTO_BED_LEVELING_GRID @@ -544,8 +544,8 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo #define Z_RAISE_BETWEEN_PROBINGS 5 // How much the Z axis will be raised when traveling from between next probing points #define Z_RAISE_AFTER_PROBING 50 // How much the Z axis will be raised after the last probing point. -//#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine. - // Useful to retract a deployable Z probe. + //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine. + // Useful to retract a deployable Z probe. //#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. @@ -631,8 +631,8 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo //#define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE HOMING_FEEDRATE_XYZ #endif -// If you have enabled the bed auto leveling and are using the same Z probe for Z homing, -// it is highly recommended you let this Z_SAFE_HOMING enabled!!! + // If you have enabled the bed auto leveling and are using the same Z probe for Z homing, + // it is highly recommended you let this Z_SAFE_HOMING enabled!!! #define Z_SAFE_HOMING // This feature is meant to avoid Z homing with Z probe outside the bed area. // When defined, it will: diff --git a/Marlin/example_configurations/delta/kossel_mini/Configuration.h b/Marlin/example_configurations/delta/kossel_mini/Configuration.h index ba37cff436..75e4d11ba4 100644 --- a/Marlin/example_configurations/delta/kossel_mini/Configuration.h +++ b/Marlin/example_configurations/delta/kossel_mini/Configuration.h @@ -518,14 +518,14 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l #else // !AUTO_BED_LEVELING_GRID - // Arbitrary points to probe. - // A simple cross-product is used to estimate the plane of the bed. - #define ABL_PROBE_PT_1_X 15 - #define ABL_PROBE_PT_1_Y 180 - #define ABL_PROBE_PT_2_X 15 - #define ABL_PROBE_PT_2_Y 20 - #define ABL_PROBE_PT_3_X 170 - #define ABL_PROBE_PT_3_Y 20 + // Arbitrary points to probe. + // A simple cross-product is used to estimate the plane of the bed. + #define ABL_PROBE_PT_1_X 15 + #define ABL_PROBE_PT_1_Y 180 + #define ABL_PROBE_PT_2_X 15 + #define ABL_PROBE_PT_2_Y 20 + #define ABL_PROBE_PT_3_X 170 + #define ABL_PROBE_PT_3_Y 20 #endif // AUTO_BED_LEVELING_GRID @@ -544,8 +544,8 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l #define Z_RAISE_BETWEEN_PROBINGS 5 // How much the Z axis will be raised when traveling from between next probing points #define Z_RAISE_AFTER_PROBING 50 // How much the Z axis will be raised after the last probing point. -//#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine. - // Useful to retract a deployable Z probe. + //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine. + // Useful to retract a deployable Z probe. //#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. @@ -635,8 +635,8 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //#define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE HOMING_FEEDRATE_XYZ #endif -// If you have enabled the bed auto leveling and are using the same Z probe for Z homing, -// it is highly recommended you let this Z_SAFE_HOMING enabled!!! + // If you have enabled the bed auto leveling and are using the same Z probe for Z homing, + // it is highly recommended you let this Z_SAFE_HOMING enabled!!! #define Z_SAFE_HOMING // This feature is meant to avoid Z homing with Z probe outside the bed area. // When defined, it will: diff --git a/Marlin/example_configurations/delta/kossel_pro/Configuration.h b/Marlin/example_configurations/delta/kossel_pro/Configuration.h index ed798c4e49..43fc9ae738 100644 --- a/Marlin/example_configurations/delta/kossel_pro/Configuration.h +++ b/Marlin/example_configurations/delta/kossel_pro/Configuration.h @@ -505,14 +505,14 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l #else // !AUTO_BED_LEVELING_GRID - // Arbitrary points to probe. - // A simple cross-product is used to estimate the plane of the bed. - #define ABL_PROBE_PT_1_X 15 - #define ABL_PROBE_PT_1_Y 180 - #define ABL_PROBE_PT_2_X 15 - #define ABL_PROBE_PT_2_Y 20 - #define ABL_PROBE_PT_3_X 170 - #define ABL_PROBE_PT_3_Y 20 + // Arbitrary points to probe. + // A simple cross-product is used to estimate the plane of the bed. + #define ABL_PROBE_PT_1_X 15 + #define ABL_PROBE_PT_1_Y 180 + #define ABL_PROBE_PT_2_X 15 + #define ABL_PROBE_PT_2_Y 20 + #define ABL_PROBE_PT_3_X 170 + #define ABL_PROBE_PT_3_Y 20 #endif // AUTO_BED_LEVELING_GRID @@ -533,8 +533,8 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l #define Z_RAISE_BETWEEN_PROBINGS 5 // How much the Z axis will be raised when traveling from between next probing points. #define Z_RAISE_AFTER_PROBING 15 // How much the Z axis will be raised after the last probing point. -//#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine. - // Useful to retract a deployable Z probe. + //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine. + // Useful to retract a deployable Z probe. //#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. @@ -620,8 +620,8 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE HOMING_FEEDRATE_XYZ #endif -// If you have enabled the bed auto leveling and are using the same Z probe for Z homing, -// it is highly recommended you let this Z_SAFE_HOMING enabled!!! + // If you have enabled the bed auto leveling and are using the same Z probe for Z homing, + // it is highly recommended you let this Z_SAFE_HOMING enabled!!! #define Z_SAFE_HOMING // This feature is meant to avoid Z homing with Z probe outside the bed area. // When defined, it will: diff --git a/Marlin/example_configurations/makibox/Configuration.h b/Marlin/example_configurations/makibox/Configuration.h index db943ee528..2f8fd73ba8 100644 --- a/Marlin/example_configurations/makibox/Configuration.h +++ b/Marlin/example_configurations/makibox/Configuration.h @@ -481,14 +481,14 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l #else // !AUTO_BED_LEVELING_GRID - // Arbitrary points to probe. - // A simple cross-product is used to estimate the plane of the bed. - #define ABL_PROBE_PT_1_X 15 - #define ABL_PROBE_PT_1_Y 180 - #define ABL_PROBE_PT_2_X 15 - #define ABL_PROBE_PT_2_Y 20 - #define ABL_PROBE_PT_3_X 170 - #define ABL_PROBE_PT_3_Y 20 + // Arbitrary points to probe. + // A simple cross-product is used to estimate the plane of the bed. + #define ABL_PROBE_PT_1_X 15 + #define ABL_PROBE_PT_1_Y 180 + #define ABL_PROBE_PT_2_X 15 + #define ABL_PROBE_PT_2_Y 20 + #define ABL_PROBE_PT_3_X 170 + #define ABL_PROBE_PT_3_Y 20 #endif // AUTO_BED_LEVELING_GRID @@ -507,14 +507,14 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l #define Z_RAISE_BETWEEN_PROBINGS 5 // How much the Z axis will be raised when traveling from between next probing points. #define Z_RAISE_AFTER_PROBING 15 // How much the Z axis will be raised after the last probing point. -//#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine. - // Useful to retract a deployable Z probe. + //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine. + // Useful to retract a deployable Z probe. //#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. -// If you have enabled the bed auto leveling and are using the same Z probe for Z homing, -// it is highly recommended you let this Z_SAFE_HOMING enabled!!! + // If you have enabled the bed auto leveling and are using the same Z probe for Z homing, + // it is highly recommended you let this Z_SAFE_HOMING enabled!!! #define Z_SAFE_HOMING // This feature is meant to avoid Z homing with Z probe outside the bed area. // When defined, it will: diff --git a/Marlin/example_configurations/tvrrug/Round2/Configuration.h b/Marlin/example_configurations/tvrrug/Round2/Configuration.h index 50b9a28801..9a6aac98d3 100644 --- a/Marlin/example_configurations/tvrrug/Round2/Configuration.h +++ b/Marlin/example_configurations/tvrrug/Round2/Configuration.h @@ -469,14 +469,14 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo #else // !AUTO_BED_LEVELING_GRID - // Arbitrary points to probe. - // A simple cross-product is used to estimate the plane of the bed. - #define ABL_PROBE_PT_1_X 15 - #define ABL_PROBE_PT_1_Y 180 - #define ABL_PROBE_PT_2_X 15 - #define ABL_PROBE_PT_2_Y 20 - #define ABL_PROBE_PT_3_X 170 - #define ABL_PROBE_PT_3_Y 20 + // Arbitrary points to probe. + // A simple cross-product is used to estimate the plane of the bed. + #define ABL_PROBE_PT_1_X 15 + #define ABL_PROBE_PT_1_Y 180 + #define ABL_PROBE_PT_2_X 15 + #define ABL_PROBE_PT_2_Y 20 + #define ABL_PROBE_PT_3_X 170 + #define ABL_PROBE_PT_3_Y 20 #endif // AUTO_BED_LEVELING_GRID @@ -495,14 +495,14 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo #define Z_RAISE_BETWEEN_PROBINGS 5 // How much the Z axis will be raised when traveling from between next probing points. #define Z_RAISE_AFTER_PROBING 15 // How much the Z axis will be raised after the last probing point. -//#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine. - // Useful to retract a deployable Z probe. + //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine. + // Useful to retract a deployable Z probe. //#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. -// If you have enabled the bed auto leveling and are using the same Z probe for Z homing, -// it is highly recommended you let this Z_SAFE_HOMING enabled!!! + // If you have enabled the bed auto leveling and are using the same Z probe for Z homing, + // it is highly recommended you let this Z_SAFE_HOMING enabled!!! #define Z_SAFE_HOMING // This feature is meant to avoid Z homing with Z probe outside the bed area. // When defined, it will: